From the Sector

Reset
331 results
(c) ZAMG/Niedermoser
Scientists ascending to the research station in the Hohe Tauern National Park
01.02.2022

Plastic snowfall in the Alps - New Empa Study about nanoplastic in the environment

In a new study, Empa researcher Dominik Brunner, together with colleagues from Utrecht University and the Austrian Central Institute for Meteorology and Geophysics, is investigating how much plastic is trickling down on us from the atmosphere. According to the study, some nanoplastics travel over 2000 kilometers through the air. According to the figures from the measurements about 43 trillion miniature plastic particles land in Switzerland every year. Researchers still disagree on the exact number. But according to estimates from the study, it could be as much as 3,000 tonnes of nanoplastics that cover Switzerland every year, from the remote Alps to the urban lowlands. These estimates are very high compared to other studies, and more research is needed to verify these numbers

The study is uncharted scientific territory because the spread of nanoplastics through the air is still largely unexplored.

In a new study, Empa researcher Dominik Brunner, together with colleagues from Utrecht University and the Austrian Central Institute for Meteorology and Geophysics, is investigating how much plastic is trickling down on us from the atmosphere. According to the study, some nanoplastics travel over 2000 kilometers through the air. According to the figures from the measurements about 43 trillion miniature plastic particles land in Switzerland every year. Researchers still disagree on the exact number. But according to estimates from the study, it could be as much as 3,000 tonnes of nanoplastics that cover Switzerland every year, from the remote Alps to the urban lowlands. These estimates are very high compared to other studies, and more research is needed to verify these numbers

The study is uncharted scientific territory because the spread of nanoplastics through the air is still largely unexplored.

The scientists studied a small area at an altitude of 3106 meters at the top of the mountain "Hoher Sonnenblick" in the "Hohe Tauern" National Park in Austria.
Every day, and in all weather conditions, scientists removed a part of the top layer of snow around a marker at 8 AM and carefully stored it. Contamination of the samples by nanoplastics in the air or on the scientists' clothes was a particular challenge. In the laboratory, the researchers sometimes had to remain motionless when a colleague handled an open sample.

The origin of the tiny particles was traced with the help of European wind and weather data. The researchers could show that the greatest emission of nanoplastics into the atmosphere occurs in densely populated, urban areas. About 30% of the nanoplastic particles measured on the mountain top originate from a radius of 200 kilometers, mainly from cities. However, plastics from the world's oceans apparently also get into the air via the spray of the waves. Around 10% of the particles measured in the study were blown onto the mountain by wind and weather over 2000 kilometers – some of them from the Atlantic.

It is estimated that more than 8300 million tonnes of plastic have been produced worldwide to date, about 60% of which is now waste. This waste erodes through weathering effects and mechanical abrasion from macro- to micro- and nanoparticles. But discarded plastic is far from the only source. Everyday use of plastic products such as packaging and clothing releases nanoplastics. Particles in this size range are so light that their movement in the air can best be compared to gases.

Besides plastics, there are all kinds of other tiny particles. From Sahara sand to brake pads, the world is buzzing through the air as abrasion. It is as yet unclear whether this kind of air pollution poses a potential health threat to humans. Nanoparticles, unlike microparticles, do not just end up in the stomach. They are sucked deep into the lungs through respiration, where their size may allow them to cross the cell-blood barrier and enter the human bloodstream. Whether this is harmful or even dangerous, however, remains to be researched.

Source:

Empa, Noé Waldmann

 Hexcel’s innovative surface technology yields parts with paint-ready surfaces for builder of luxury yachts (c) Hexcel
Sunseeker 90 Ocean Luxury Yacht
26.01.2022

Hexcel Selected for Sunseeker 90 Ocean Luxury Yacht

  • Hexcel HexPly® XF Selected for High-Quality, Paint-Ready Parts for Sunseeker 90 Ocean Luxury Yacht
  • Hexcel’s innovative surface technology yields parts with paint-ready surfaces for builder of luxury yachts

Yacht builder Sunseeker has chosen Hexcel’s HexPly® XF surface technology to produce prepreg parts with high-quality, paint-ready surfaces quickly and efficiently for its 90 Ocean luxury yacht, one of its newest models.

The lightweight composite hardtop for the Sunseeker 90 Ocean yacht is manufactured from a combination of HexPly® XF and Hexcel's HexPly® SuperFIT® semi-preg. The hardtop is lighter in weight than versions made using resin-infusion processes, and it de-molds with a pinhole-free surface that needs minimal preparation to be ready for paint. Sunseeker has recorded an overall reduction in process time of around 30%, saving three days of manufacturing time per hardtop.

  • Hexcel HexPly® XF Selected for High-Quality, Paint-Ready Parts for Sunseeker 90 Ocean Luxury Yacht
  • Hexcel’s innovative surface technology yields parts with paint-ready surfaces for builder of luxury yachts

Yacht builder Sunseeker has chosen Hexcel’s HexPly® XF surface technology to produce prepreg parts with high-quality, paint-ready surfaces quickly and efficiently for its 90 Ocean luxury yacht, one of its newest models.

The lightweight composite hardtop for the Sunseeker 90 Ocean yacht is manufactured from a combination of HexPly® XF and Hexcel's HexPly® SuperFIT® semi-preg. The hardtop is lighter in weight than versions made using resin-infusion processes, and it de-molds with a pinhole-free surface that needs minimal preparation to be ready for paint. Sunseeker has recorded an overall reduction in process time of around 30%, saving three days of manufacturing time per hardtop.

The hardtop provides shade and protection for the yacht’s uppermost deck space. Its reduced weight helps to ensure the stability of the vessel, and the paint-ready finish with HexPly XF provides Sunseeker with more options for customizing its color to the individual needs of its clients.
 
HexPly XF is a lightweight, non-woven semi-preg that eliminates the need to use a traditional in-mold gel coat. The innovative surface technology significantly reduces the costly and time-consuming refinishing work typically required to impart a paint-ready finish to prepreg or semi-preg parts, and yields lightweight, consistent components in short cycle times.

Working with Sunseeker, Hexcel developed a material format, a laminate ply sequence, and a production process that satisfied the structural requirements for the hardtop and enabled the yacht builder’s production team to lay up and cure the part in a single shot – slashing cycle times.

Hexcel supplies Sunseeker with a HexPly XF product that comprises both the surface layer and the first structural reinforcement ply, eliminating the need for a cosmetic barrier coat. Neither the HexPly XF surface layer nor the following layers of HexPly SuperFIT require time-consuming debulking steps – significantly reducing lay-up time – and both are based on Hexcel's rapid-curing M79 epoxy resin system. Adhesive resin films are not needed to bond the hardtop’s foam core, as the resin content of the SuperFIT plies has been adjusted to further reduce overall process time.

Once de-molded, the cured hardtops are inspected before they are passed to Sunseeker’s finishing and painting technicians for final preparation and painting. The HexPly XF resin surface allows the yacht builder’s quality technicians to inspect the laminate below quickly and easily, ensuring the quality and consistency of the structural reinforcement plies.

“Composite materials that improve our production processes, as well as great technical support, are what makes working with Hexcel such a success story," said Stuart Vaughan-Jones, Composite Development Manager, Sunseeker. "With the switch from gel coat and resin infusion to HexPly XF and SuperFIT in the new hardtops, we are now building lighter, more consistent parts, more quickly than before, with a higher quality surface finish. XF really has ticked all the boxes.”  

Garth Thomas, Account Manager – Marine, Hexcel, said: "With the HexPly XF surface technology now well established, XF will soon be used in other large moldings where minimizing weight is critical, as well as additional hardtops across the Sunseeker model range."

(c) Messe Frankfurt (HK) Ltd.
21.01.2022

Promising conditions for Cinte Techtextil China in September

Promising conditions in the technical textiles and nonwovens market are expected to provide ample opportunities for suppliers at this year’s Cinte Techtextil China. The fair, which last year saw 366 exhibitors and 14,868 visits, will take place from 6 – 8 September 2022 at the Shanghai New International Expo Centre. Flexible exhibiting options will once again be available for overseas companies.

Ms Wendy Wen, Senior General Manager of Messe Frankfurt (HK) Ltd, explained the positive conditions that exhibitors should expect at the fair thusly: “The pandemic has led to a surge in Chinese exports of both technical textiles and nonwovens, the latter in particular. The country remains the largest supplier of nonwovens, comprising one-third of the global total, yet still requires the advanced offerings of overseas machinery suppliers, as well as supplies of raw materials, to support its export production.”

Promising conditions in the technical textiles and nonwovens market are expected to provide ample opportunities for suppliers at this year’s Cinte Techtextil China. The fair, which last year saw 366 exhibitors and 14,868 visits, will take place from 6 – 8 September 2022 at the Shanghai New International Expo Centre. Flexible exhibiting options will once again be available for overseas companies.

Ms Wendy Wen, Senior General Manager of Messe Frankfurt (HK) Ltd, explained the positive conditions that exhibitors should expect at the fair thusly: “The pandemic has led to a surge in Chinese exports of both technical textiles and nonwovens, the latter in particular. The country remains the largest supplier of nonwovens, comprising one-third of the global total, yet still requires the advanced offerings of overseas machinery suppliers, as well as supplies of raw materials, to support its export production.”

Ms Wen continued: “Domestically, China is seeing increasing consumption of functional apparel, sportswear and personal protection items. Heightened health and sanitary regulations and new hygiene habits will also continue to drive demand, especially for nonwovens, well into the future. There has also been a post-pandemic boost in demand for filter, greenhouse covering and high-density fabrics amongst others. All of this adds up to a wealth of opportunities for overseas companies to take advantage of, as was experienced in the 2021 edition of the fair.”

Exhibitor and visitor experiences in 2021
“Our organisation promotes US cotton and we hope to use this platform to meet more companies and brands in the nonwovens industry who are interested in US cotton, and to meet up with old friends to discuss the current situation and industry trends. We also found some new potential clients this time.” Mr Eric Ni, Senior Manager, China Supply Chain Marketing, Fabrics, Garments and Nonwovens, Cotton Council International, USA

“Cinte Techtextil China is a professional exhibition that brings together cutting-edge technologies and products, allowing us to quickly learn about innovative technology trends in the industry. I’ve been particularly impressed by the biodegradable products in the Innovation Showcase. In addition, I am sourcing mask-related products and mops, and I have found some companies that I’m interested in.” Ms Claire Zhang, Senior Scientist, Personal Health, Philips Research China, Philips (China) Investment Co Ltd, China

Source:

Messe Frankfurt (HK) Ltd.

06.01.2022

Interdisziplinäre Weiterbildung zur Gestaltung der Energie- und Rohstoffwende

  • Berufsbegleitendes Studium
  • Mit DYNERGY zum »Cross-Industry Manager«

Für die Energie- und Rohstoffwende muss sich die Wirtschaft neu aufstellen: weg von großen stationären Anlagen und fossilen Rohstoffen hin zu kleinen flexiblen Einheiten mit variierenden Einsatzstoffen und der Nutzung von erneuerbaren Energien. Für diesen Wandel brauchen Unternehmen Fachkräfte mit Know-how zur Dynamik von Energie- und Rohstoffsystemen. Einen Weg, diese Expertise auf- und auszubauen, bieten die FernUniversität in Hagen und das Fraunhofer UMSICHT mit dem interdisziplinären Studium zur Dynamik der Sektorenkopplung DYNERGY. Die berufsbegleitende Weiterbildung startet zum Sommersemester 2022, Einschreibungen sind bis zum 1. März möglich.

Das modulare Angebot richtet sich an Fach- und Führungskräfte – insbesondere Planungsverantwortliche, Projektleitende und -mitarbeitende sowie Prozess-, Betriebs-, Versorgungs- und Energieingenieur*innen. Aber auch Berufs- und Quereinsteiger*innen aus Unternehmen, Kommunen, Verbänden oder Behörden mit Interesse an der Energie- und Rohstoffwende können teilnehmen.

  • Berufsbegleitendes Studium
  • Mit DYNERGY zum »Cross-Industry Manager«

Für die Energie- und Rohstoffwende muss sich die Wirtschaft neu aufstellen: weg von großen stationären Anlagen und fossilen Rohstoffen hin zu kleinen flexiblen Einheiten mit variierenden Einsatzstoffen und der Nutzung von erneuerbaren Energien. Für diesen Wandel brauchen Unternehmen Fachkräfte mit Know-how zur Dynamik von Energie- und Rohstoffsystemen. Einen Weg, diese Expertise auf- und auszubauen, bieten die FernUniversität in Hagen und das Fraunhofer UMSICHT mit dem interdisziplinären Studium zur Dynamik der Sektorenkopplung DYNERGY. Die berufsbegleitende Weiterbildung startet zum Sommersemester 2022, Einschreibungen sind bis zum 1. März möglich.

Das modulare Angebot richtet sich an Fach- und Führungskräfte – insbesondere Planungsverantwortliche, Projektleitende und -mitarbeitende sowie Prozess-, Betriebs-, Versorgungs- und Energieingenieur*innen. Aber auch Berufs- und Quereinsteiger*innen aus Unternehmen, Kommunen, Verbänden oder Behörden mit Interesse an der Energie- und Rohstoffwende können teilnehmen.

Im Fokus: Sektorenkopplung und cross-industrielle Verbünde
In drei Modulen erarbeiten sich die Studierenden eine fundierte und anwendungsorientierte Begriffs- und Verständnisbasis zu Sektorenkopplung und cross-industriellen Verbünden. Konkret befassen sie sich mit der Frage, wie sie Energie- und Produktionssysteme für sich verändernde Märkte und Rahmenbedingungen gestalten können – und zwar unabhängig von Prozessen und Branchen. Im Themenbereich »Dynamik von Energie- und Rohstoffsystemen« liegt der Fokus auf dynamischen Vorgängen bei der Kopplung von Energie- und Rohstoffsystemen. Hierbei stehen insbesondere Prinzipien der numerischen Modellierung, Simulation und Optimierung von Energie- und Prozesssystemen auf dem Lehrplan.

Lernen via Selbststudium, Modeling based Learning und Online-Veranstaltungen
Das Lernen erfolgt in erster Linie via Selbststudium: Die Teilnehmenden erhalten ein digitales Skript sowie den Zugang zu einer webbasierten Programmierungsumgebung. Dort können sie im Modeling based Learning die Modellierung relevanter Energie- und Produktionssysteme mit Python anhand praxisrelevanter Beispiele sowohl in Einzel- als auch in Gruppenarbeit üben und vertiefen. Darüber hinaus befassen sie sich die Teilnehmenden mit Digitalisierung in der Verfahrens- und Energietechnik, in dessen Rahmen die Möglichkeit besteht, eigene Erfahrungen mit Sensoren, Datenerfassung und Datennutzung in Modellen zu sammeln.

Abschluss als »Cross-Industry Manager«
Wer sich auf diesem Wege zum »Cross-Industry Manager« qualifiziert, erhält ein Zertifikat mit einem Gesamtumfang von 15 ECTS gemäß § 62 des Hochschulgesetzes Nordrhein-Westfalen. Weitere Details zum Abschluss der Weiterbildung sowie zu Inhalten, Aufbau und Betreuung liefern zwei kostenlose Info-Veranstaltungen am 20. Januar und 17. Februar 2022, jeweils von 17.30 bis 18.30 Uhr (digital). Anmeldungen sind über www.weiterbildung-dynergy.de möglich.

Source:

Fraunhofer UMSICHT

photo: pixabay
03.01.2022

Launch of the European project EU-ALLIANCE for advanced materials

EU-ALLIANCE aims to support SMEs internationalisation in the fields of technical textile, connectivity and advanced materials to address dual use markets in four targeted countries: The United States, Canada, Japan and Indonesia. The EU-ALLIANCE project is funded by the European Union's COSME programme. It brings together 6 key clusters representing nearly 900 companies: Techtera (France); Systematic (France); PO.IN.TEX - Textile innovation cluster (Italy); NTT - Next Technology Tecnotessile (Italy); NIDV - Industries for Defence and Security (Netherlands); SIIT - Intelligent System Integrated Technologies (Italy).

EU-ALLIANCE aims to support SMEs internationalisation in the fields of technical textile, connectivity and advanced materials to address dual use markets in four targeted countries: The United States, Canada, Japan and Indonesia. The EU-ALLIANCE project is funded by the European Union's COSME programme. It brings together 6 key clusters representing nearly 900 companies: Techtera (France); Systematic (France); PO.IN.TEX - Textile innovation cluster (Italy); NTT - Next Technology Tecnotessile (Italy); NIDV - Industries for Defence and Security (Netherlands); SIIT - Intelligent System Integrated Technologies (Italy).

On November 25, the partners hosted a webinar to present the project and the opportunities it will generate. This webinar was also an opportunity to position the participants to benefit from the services generated by the project (market research, commercial missions, B2B meetings, etc.), communicate your needs and thus join the selection of companies that will be able to benefit from European support for these actions. Beyond this internationalisation objective, the project also aims to encourage intra-European collaboration and synergies between the various members of the partner clusters.

Source:

EU-ALLIANCE

UMSICHT-Wissenschaftspreis 2022: Die Bewerbungsphase ist gestartet. © Fraunhofer UMSICHT
22.12.2021

UMSICHT-Wissenschaftspreis 2022: Die Bewerbungsphase ist gestartet.

  • Ausschreibung UMSICHT-Wissenschaftspreis 2022: Gesellschaft mit Vertrauen in die Wissenschaft

Nachhaltigkeit ist untrennbar mit gesellschaftlichen Veränderungen verknüpft. Dabei stellt die Wissenschaft Basis und Rahmen zur Verfügung, um nachhaltiges Handeln zu etablieren. Das kann wiederum nur gelingen, wenn die Beteiligten auf Augenhöhe miteinander kommunizieren und sich gegenseitig vertrauen. Mit dem UMSICHT-Wissenschaftspreis werden Menschen ausgezeichnet, die mit ihrer Arbeit das Vertrauen zwischen Wissenschaft und Gesellschaft stärken. Der Preis wird in den Kategorien Wissenschaft und Journalismus verliehen und ist mit insgesamt 10 000 Euro dotiert. Bewerbungen können ab sofort und bis zum 28. Februar 2022 eingereicht werden.

  • Ausschreibung UMSICHT-Wissenschaftspreis 2022: Gesellschaft mit Vertrauen in die Wissenschaft

Nachhaltigkeit ist untrennbar mit gesellschaftlichen Veränderungen verknüpft. Dabei stellt die Wissenschaft Basis und Rahmen zur Verfügung, um nachhaltiges Handeln zu etablieren. Das kann wiederum nur gelingen, wenn die Beteiligten auf Augenhöhe miteinander kommunizieren und sich gegenseitig vertrauen. Mit dem UMSICHT-Wissenschaftspreis werden Menschen ausgezeichnet, die mit ihrer Arbeit das Vertrauen zwischen Wissenschaft und Gesellschaft stärken. Der Preis wird in den Kategorien Wissenschaft und Journalismus verliehen und ist mit insgesamt 10 000 Euro dotiert. Bewerbungen können ab sofort und bis zum 28. Februar 2022 eingereicht werden.

Die aktuellen Diskussionen über die Sicherstellung von Nachhaltigkeit für die nächsten Generationen zeigen, dass Deutschland in vielen Bereichen umwelt- und klimafreundlicher werden muss. Um das zu erreichen, bedarf es einer breiten Akzeptanz in der Gesellschaft. Denn: Die damit einhergehenden gesellschaftlichen Veränderungen – etwa durch die Vermeidung von Plastik, den Kohleausstieg oder die Mobilitätswende – haben direkten Einfluss auf unseren Alltag. Der Wissenschaft wird in dem Zusammenhang eine bedeutende Aufgabe zugeschrieben, indem sie eine vielfältige und verständliche Auseinanderset­zung mit Forschungsergebnissen und neuen Technologien ermöglicht.

Forschungsthemen verständlich kommunizieren

Um den Dialog zwischen Wissenschaft und Gesellschaft zu unterstützen, hat der UMSICHT-Förderverein den UMSICHT-Wissenschaftspreis initiiert. Seit 2010 werden Menschen ausgezeichnet, die Forschungsergebnisse aus den Bereichen Umwelt-, Verfahrens- und Energietechnik – den Kernthemen des Fraunhofer UMSICHT – auf eine herausragende Weise der Gesellschaft zugänglich machen. Das Preisgeld verteilt sich auf einen mit 8000 Euro dotierten Preis in der Kategorie Wissenschaft und einen mit 2000 Euro dotierten Preis für journalistische Arbeiten.

Jetzt online bewerben

Zugelassen sind sämtliche veröffentlichte Arbeiten, die sich mit den Themen Umwelt-, Verfahrens- oder Energietechnik beschäftigen. Die Arbeiten dürfen nicht älter als zwei Jahre sein und können auf Deutsch oder Englisch eingereicht werden. Reine Konzepte, Fotoarbeiten, Bücher sowie nicht veröffentlichte Arbeiten können für den UMSICHT-Wissenschaftspreis nicht angenommen werden. Bei Gemeinschaftsarbeiten ist darauf zu achten, dass die Haupt-Anteilsträgerin bzw. der Haupt-Anteilsträger die Arbeit einreicht.

Bewerbungen sind schnell und unkompliziert über das Online-Formular möglich. Bewerbungsschluss ist der 28. Februar 2022.

Source:

Fraunhofer UMSICHT

© Recyda GmbH
22.12.2021

Fraunhofer UMSICHT testet Verpackungstool

Wie kreislauffähig sind alltägliche Verpackungen?
Verpackungen sind komplex: eine Umverpackung aus Karton, Einzelteile zusätzlich in PET-Folie verpackt, ein wasserlösliches Label oder vielleicht eine Klebefolie. Um die Rezyklierbarkeit alltäglicher Verpackungen zu bewerten, müssen Verpackungsart, -komponenten und -materialien berücksichtigt werden. Zudem sind umfangreiche Kenntnisse über (multi-)nationale Vorgaben notwendig. Die Recyda GmbH hat ein flexibles Bewertungstool entwickelt, welches verschiedene Vorgaben (»Regelwerke«) der Recyclingfähigkeit modellieren kann. Fraunhofer UMSICHT hat die digitale Umsetzung der Vorgaben des MstSZSVr (Mindeststandard der Zentralen Stelle Verpackungsregister) als eines der in Recyda abgebildeten Regelwerke geprüft. Das Ergebnis: Recyda ist ein nutzerfreundliches Bewertungstool, das die Rezyklierbarkeit von Verpackungen analysiert. Es kann auch als Hilfestellung herangezogen werden, um zukünftige Verpackungen so zu gestalten, dass sie auf Recyclingfähigkeit optimiert sind.

Wie kreislauffähig sind alltägliche Verpackungen?
Verpackungen sind komplex: eine Umverpackung aus Karton, Einzelteile zusätzlich in PET-Folie verpackt, ein wasserlösliches Label oder vielleicht eine Klebefolie. Um die Rezyklierbarkeit alltäglicher Verpackungen zu bewerten, müssen Verpackungsart, -komponenten und -materialien berücksichtigt werden. Zudem sind umfangreiche Kenntnisse über (multi-)nationale Vorgaben notwendig. Die Recyda GmbH hat ein flexibles Bewertungstool entwickelt, welches verschiedene Vorgaben (»Regelwerke«) der Recyclingfähigkeit modellieren kann. Fraunhofer UMSICHT hat die digitale Umsetzung der Vorgaben des MstSZSVr (Mindeststandard der Zentralen Stelle Verpackungsregister) als eines der in Recyda abgebildeten Regelwerke geprüft. Das Ergebnis: Recyda ist ein nutzerfreundliches Bewertungstool, das die Rezyklierbarkeit von Verpackungen analysiert. Es kann auch als Hilfestellung herangezogen werden, um zukünftige Verpackungen so zu gestalten, dass sie auf Recyclingfähigkeit optimiert sind.

Das webbasierte Tool zeichnet sich durch einen klar strukturierten Aufbau aus, der es neuen Anwendern nach einer halb- bis einstündigen Einarbeitungszeit ermöglicht, eigene Verpackungsprojekte einzupflegen und ihre Recyclingfähigkeit digital zu bewerten. Unterschieden nach Verpackungsart, Verpackungskomponenten und Verpackungsmaterialien können Anwendende ihre Verpackung in wenigen Prozessschritten — dargestellt in einzelnen Eingabemasken — bewerten. Innerhalb der Masken vereinfachen vordefinierte Verpackungsarten die Eingabe; neben der Art werden auch Gewicht und Volumen der Verpackung abgefragt ebenso wie Fragen zu Farbe und Ablösbarkeit der Verpackungskomponenten. Das Ergebnis wird — je nach verwendetem Regelwerk — skaliert in Prozent bzw. farbig dargestellt und mit Hinweisen zur Einordnung im Vergleich zu den jeweiligen (trans)nationalen Regelungen versehen. Fraunhofer UMSICHT testete das Tool anhand verschiedener Musterverpackungen.

Das Recyda Tool wird stetig weiterentwickelt und mit neuesten Daten zu länderspezifischen Recyclingvorgaben aktualisiert. Fraunhofer UMSICHT empfiehlt als weitere Ergänzung, zusätzlich ein Glossar zu den Begrifflichkeiten des MstSZSVr zur Verfügung zu stellen und regelmäßig zu aktualisieren, damit auch Fachfremde das Tool nutzen können. Zudem halten die Forschenden es für sinnvoll, Handlungsempfehlungen für unterschiedliche Entsorgungsmöglichkeiten oder Trennbarkeiten zu erstellen.

Source:

Fraunhofer-Institut für Umwelt-, Sicherheits- und Energietechnik UMSICHT

(c) Messe Frankfurt, deepak@deepakdavda.com
13.12.2021

Techtextil India: First post-lockdown edition with overwhelming responsive from industry

After three-days of product sourcing and business networking, Techtextil India 2021 in Mumbai concluded in a strong and positive note. The trade fair emerged as a crucial meeting place for the technical textile players to rebuild their supplier links, promote industry integration and engage in lucrative knowledge exchange.

The eighth edition of Techtextil India stood out to be a ground-breaking business platform for the technical textile sector to build a new and strong foundation in the new normal. The aim of the new edition was to promote industry unification and business recovery across the value chain of technical textiles.

The event held at Bombay Exhibition Centre was inaugurated by major dignitaries, including Shri Ajit Chavan, Secretary – Textiles Committee, Ministry of Textiles, Government of India. Over the course of its three buzzing days, the show garnered an attendance of 4,087 visitors drawn by live demonstration of latest products, technologies and innovations exhibited by over 150 technical textile brands on the show floor.

After three-days of product sourcing and business networking, Techtextil India 2021 in Mumbai concluded in a strong and positive note. The trade fair emerged as a crucial meeting place for the technical textile players to rebuild their supplier links, promote industry integration and engage in lucrative knowledge exchange.

The eighth edition of Techtextil India stood out to be a ground-breaking business platform for the technical textile sector to build a new and strong foundation in the new normal. The aim of the new edition was to promote industry unification and business recovery across the value chain of technical textiles.

The event held at Bombay Exhibition Centre was inaugurated by major dignitaries, including Shri Ajit Chavan, Secretary – Textiles Committee, Ministry of Textiles, Government of India. Over the course of its three buzzing days, the show garnered an attendance of 4,087 visitors drawn by live demonstration of latest products, technologies and innovations exhibited by over 150 technical textile brands on the show floor.

The event received an overwhelming response, reflecting industry’s keen interest to explore new developments and opportunities in technical textiles. In regards to the same, Mr Abhijit Kulkarni, President – Textile Engineering Group, A.T.E. India, stated: “It was the first and best physical show also on hybrid mode filled with enthusiastic buyers and customers who visited our booth and had very fruitful discussions with us. Several leading textile manufacturers visited our stalls, including: Strata Geosystems India, SKAPS Industries, Reliance Composites, Paramount Textiles, and Welspun, to name a few.”

Alok Masterbatches Pvt Ltd, Khosla Profile Pvt Ltd, ATE Group, Lucky International, Meera Industries Limited, Park Non-Woven Pvt Ltd, Sarex Chemicals, SICAM, Suntech Geotextile Pvt Ltd and Weavetech Engineers, were among the leading Indian companies exhibiting at the show.

The significance of the three-day fair was further elevated by the German pavilion. Technical textile manufacturers from Germany, such as Autefa Solution Germany GmbH, DILO Systems GmbH, Emtec Electronic GmbH, Georg Sahm GmbH & Co, Karl Mayer Verwaltungsgesellschaft mbH, Merz Maschinenfabrik GmbH and Oerlikon Barmag Zweigniederlassung der Oerlikon Textile GmbH & Co, displayed their latest technologies on the show floor, which garnered significant attention from the Indian buyers.

The first Digital Symposium was another highlight of Techtextil India 2021. The forum delved into a series of crucial topics in technical textiles discussing PLI schemes, FDI opportunities and policies, investment opportunities in Tamil Nadu, & New Investment Opportunities, Sustainable Technical Textiles and Global sustainable approach for Textiles with Antimicrobial Performance.

Concluding on a successful note, Techtextil India 2021 emerged as a platform of new beginnings for the technical textiles sector and for businesses trying to retain their shape and seeking momentum after the tough pandemic phase.

Source:

Messe Frankfurt HK

(c) Fraunhofer UMSICHT
10.12.2021

Fraunhofer UMSICHT: Studium »infernum« ist Vorbild für nachhaltige Entwicklung

Die Weiterbildung infernum von FernUniversität und Fraunhofer UMSICHT erhielt erneut die nationale Auszeichnung des Bundesministeriums für Bildung und Forschung und der Deutschen UNESCO-Kommission für Bildung für nachhaltige Entwicklung.

Am 10. Dezember haben das Bundesministerium für Bildung und Forschung und die Deutsche UNESCO-Kommission die Nationale Auszeichnung – Bildung für nachhaltige Entwicklung (BNE)im neuen UNESCO-Programm »BNE 2030« vergeben.

Das »Interdisziplinäre Fernstudium Umweltwissenschaften« überzeugte die Jury durch ein beispielhaftes Engagement für BNE und einen besonderen Einsatz für die Globalen Nachhaltigkeitsziele (Sustainable Development Goals) der Vereinten Nationen.

Damit wurde das Weiterbildungsstudium infernum, gemeinsam angeboten von der FernUniversität in Hagen und Fraunhofer UMSICHT in Oberhausen, zum nunmehr sechsten Mal von der deutschen UNESCO-Kommission und vom Bundesministerium für Bildung und Forschung für sein Engagement im Bereich Bildung für Nachhaltige Entwicklung ausgezeichnet.

Die Weiterbildung infernum von FernUniversität und Fraunhofer UMSICHT erhielt erneut die nationale Auszeichnung des Bundesministeriums für Bildung und Forschung und der Deutschen UNESCO-Kommission für Bildung für nachhaltige Entwicklung.

Am 10. Dezember haben das Bundesministerium für Bildung und Forschung und die Deutsche UNESCO-Kommission die Nationale Auszeichnung – Bildung für nachhaltige Entwicklung (BNE)im neuen UNESCO-Programm »BNE 2030« vergeben.

Das »Interdisziplinäre Fernstudium Umweltwissenschaften« überzeugte die Jury durch ein beispielhaftes Engagement für BNE und einen besonderen Einsatz für die Globalen Nachhaltigkeitsziele (Sustainable Development Goals) der Vereinten Nationen.

Damit wurde das Weiterbildungsstudium infernum, gemeinsam angeboten von der FernUniversität in Hagen und Fraunhofer UMSICHT in Oberhausen, zum nunmehr sechsten Mal von der deutschen UNESCO-Kommission und vom Bundesministerium für Bildung und Forschung für sein Engagement im Bereich Bildung für Nachhaltige Entwicklung ausgezeichnet.

Andrea Ruyter-Petznek, Leiterin des Referats Bildung in Regionen, Bildung für nachhaltige Entwicklung im Bundesministerium für Bildung und Forschung, und der Generalsekretär der Deutschen UNESCO-Kommission Dr. Roman Luckscheiter zeichneten im Rahmen einer digitalen Auszeichnungsfeier 29 Akteurinnen und Akteure für ihr herausragendes Engagement für Bildung für nachhaltige Entwicklung aus. Die 29 geehrten Initiativen erreichen Menschen mit innovativen Bildungsangeboten, Inhalten und Ideen und befähigen Lernende, aktiv und verantwortungsvoll an der Gestaltung einer nachhaltigen Zukunft mitzuwirken.

Der Studiengang »Interdisziplinäre Fernstudium Umweltwissenschaften – infernum«
Die erfolgreiche und wissenschaftlich fundierte Lösung komplexer Aufgabenstellungen in den Bereichen Umwelt und Nachhaltigkeit setzt eine interdisziplinäre Denk- und Herangehensweise voraus. infernum vermittelt das hierzu notwendige Wissen und befähigt dazu, die „Sprachen“ der unterschiedlichen Disziplinen verstehen zu können. infernum zeichnet sich durch die Interdisziplinarität der Lehrinhalte, die fachliche Breite des Lehrangebotes und die Flexibilität der Organisation aus. Es ist in dieser Form einzigartig in der universitären Weiterbildungslandschaft in Deutschland. Als Fernstudienangebot ermöglicht es eine wissenschaftliche Weiterbildung neben Beruf und Familie. Die Studierenden können sich ihr individuelles Lernprogramm aus einzelnen Modulen zusammenstellen und den Abschluss Master of Science sowie unterschiedliche Zertifikatsabschlüsse erwerben.

Bildung für nachhaltige Entwicklung
Nachhaltige Entwicklung bedeutet, Menschenwürde und Chancengerechtigkeit für alle in einer intakten Umwelt zu verwirklichen. Bildung ist für eine nachhaltige Entwicklung zentral. Sie versetzt Menschen in die Lage, Entscheidungen für die Zukunft zu treffen und abzuschätzen, wie sich eigene Handlungen auf künftige Generationen oder das Leben in anderen Weltregionen auswirken. In der globalen Nachhaltigkeitsagenda 2030 der Vereinten Nationen ist die Umsetzung von BNE als Ziel für die Weltgemeinschaft festgeschrieben. Im Anschluss an das UNESCO-Weltaktionsprogramm Bildung für nachhaltige Entwicklung (2015 – 2019) beteiligt sich Deutschland am UNESCO-Folgeprogramm »BNE 2030«, das eng an die Agenda und ihre 17 globalen Nachhaltigkeitsziel geknüpft ist.

Source:

Fraunhofer UMSICHT

03.12.2021

Heimtextil from 11 - 14 January 2022 is cancelled

Against the background of the worsening pandemic situation in Germany over the past two weeks and the associated restrictions, Heimtextil, scheduled to take place in the second week of January, is cancelled. Messe Frankfurt is working with the industry to determine whether and in what form a new offering in the summer of 2022 can be organised to run parallel to the Techtextil/Texprocess trade fair duo. Later events such as Ambiente, Christmasworld, Creativeworld, Paperworld and Frankfurt Fashion Week are still planning to take place at the present time.

Against the background of the worsening pandemic situation in Germany over the past two weeks and the associated restrictions, Heimtextil, scheduled to take place in the second week of January, is cancelled. Messe Frankfurt is working with the industry to determine whether and in what form a new offering in the summer of 2022 can be organised to run parallel to the Techtextil/Texprocess trade fair duo. Later events such as Ambiente, Christmasworld, Creativeworld, Paperworld and Frankfurt Fashion Week are still planning to take place at the present time.

Due to the unforeseeable dynamics in the development of the pandemic, the reciprocal and cumulative effects of the relevant factors, as well as the extreme escalation and deterioration of the pandemic situation in Germany within a very short period of time, including the decisions taken at the Conference of Minister Presidents on 02.12.2021, the date of Heimtextil right at the beginning of the year, in the second week of January, cannot be kept. Heimtextil, the leading international trade fair for home and contract textiles, will be cancelled. Messe Frankfurt is working closely with all industry partners to find out whether and within what framework Heimtextil can be held parallel to Techtextil and Texprocess from 21 to 24 June 2022.

Heimtextil as an international trade fair has always kicked off the spring trade fair season and is the first major international trade fair in Germany directly after Christmas and New Year with exhibitors and visitors from over 135 countries. The exponential increase in the number of infections in a very short period of time and the accompanying multitude of developments and resolutions that are clearly outside the realm of influence of the organizer have led to a significant deterioration in the general conditions and necessary requirements for holding Heimtextil as a major trade fair of international relevance at this early stage. These developments include in particular the classification of Germany as a high-risk area and the associated travel warnings, international and intercontinental travel restrictions in India, Japan, the United States and Great Britain, as well as the quarantine obligation and “2G” (only with vaccinated and recovered status) requirements without recognition of the WHO vaccine list in Germany. Equally important are the steadily rising infection figures and the accompanying urgent appeal, including by the Robert Koch Institute, to reduce contacts to a minimum and to cancel all major events.

A large number of the exhibiting and visiting companies at Heimtextil are currently reacting to this with travel and trade fair attendance bans out of an obligation of concern towards their employees to protect them from health risks. The global willingness to travel is continuing to fall rapidly.

The planning and staging of the other spring trade fairs Ambiente, Christmasworld, Creativeworld and Paperworld is not affected. Due to their later dates in the year, at the end of January and mid-February respectively, these fairs are still planning to take place at the present time. Compared to Heimtextil, which is the most international trade fair at the Frankfurt location, Frankfurt Fashion Week currently has a much lower international profile and from this perspective can therefore still take place. The extremely volatile situation is continuously reviewed and evaluated in close exchange with the relevant authorities and industry partners.

Source:

Messe Frankfurt

Dr. Berend Lindner, Staatssekretär im Ministerium, Andreas Halle, Geschäftsführer von Seilflechter, Alexandra Gruffke, Assistenz der Geschäftsführung von Seilflechter. (von links nach rechts)
25.11.2021

SEILFLECHTER vom Land Niedersachsen mit Zertifikat „Zukunftsfest“ ausgezeichnet

Mit dem Zertifikat „Zukunftsfest“ zeichnen das Niedersächsische Ministerium für Wirtschaft, Arbeit, Verkehr und Digitalisierung und die Demografieagentur für die Wirtschaft GmbH niedersächsische Unternehmen und Verwaltungen aus, die sich aktuellen Herausforderungen hinsichtlich Digitalisierung, Nachhaltigkeit und demografischem Wandel aktiv stellen und erfolgreiche  Maßnahmen umsetzen.

Das Traditionsunternehmen SEILFLECHTER aus Braunschweig erhielt das Zertifikat für ihre digitale Lösung im Prozess der Seilprüfungen. „Die Ausgangssituation war, dass wir unseren Kunden und uns eine bessere Übersicht über die zur Prüfung anstehenden Produkte zu gewährleisten“, so Geschäftsführer Andreas Halle. Durch die Kennzeichnung der zu prüfenden Produkte mit einem RFID Chip (Radio Frequency Idenfification Chip) und der Aufbau einer dazugehörigen Datenbank wurde dieses Ziel erreicht.

Mit dem Zertifikat „Zukunftsfest“ zeichnen das Niedersächsische Ministerium für Wirtschaft, Arbeit, Verkehr und Digitalisierung und die Demografieagentur für die Wirtschaft GmbH niedersächsische Unternehmen und Verwaltungen aus, die sich aktuellen Herausforderungen hinsichtlich Digitalisierung, Nachhaltigkeit und demografischem Wandel aktiv stellen und erfolgreiche  Maßnahmen umsetzen.

Das Traditionsunternehmen SEILFLECHTER aus Braunschweig erhielt das Zertifikat für ihre digitale Lösung im Prozess der Seilprüfungen. „Die Ausgangssituation war, dass wir unseren Kunden und uns eine bessere Übersicht über die zur Prüfung anstehenden Produkte zu gewährleisten“, so Geschäftsführer Andreas Halle. Durch die Kennzeichnung der zu prüfenden Produkte mit einem RFID Chip (Radio Frequency Idenfification Chip) und der Aufbau einer dazugehörigen Datenbank wurde dieses Ziel erreicht.

Auf dem Chip, der eingenäht, aufgeklebt oder als Kabelbinder fungiert, befinden sich alle wichtigen Daten (welches Produkt, Seriennummer, Hersteller, Standort, nächster Prüftermin, etc.).
Die wichtigen Prüfintervalle und somit gesetzliche Vorgaben können nun sicher eingehalten werden. Darüber hinaus gelangen ab sofort nur die Produkte in die Prüfung, die auch tatsächlich geprüft werden müssen. Das Feedback der Kunden, laut Aussage von SEILFLECHTER, war große Zufriedenheit, da sie Kosten für unnötige Prüfungen zukünftig einsparen werden.

Source:

SEILFLECHTER Tauwerk GmbH

(c) AVK - Industrievereinigung Verstärkte Kunststoffe e. V.
24.11.2021

The AVK – Industrievereinigung Verstärkte Kunststoffe – presents its Innovation Awards 2021

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

Category “Research and Science”
First place in the “Research and Science” category was awarded to the German Aerospace Center (DLR) for its Bondline Control Technology (BCT). This innovative process is used for quality control and assurance of bonded joints. The core element is a porous fabric which is applied to a joining surface using an epoxy adhesive or matrix resin. Peeling away the fabric creates a chemically reactive and undercut surface and can also be used as a test to check adhesion to the substrate. BCT has potential in a variety of possible applications. For example, peel ply can be replaced by BCT fabric to produce composite components with an optimised joining surface. The cost-effective BCT peel test is suitable for coupon testing and process control. In addition, the combined adhesion test and surface pre-treatment can be used for quality assurance of bonded repairs on fibre composite structures.

Second place was taken by the Institute of Textile Technology (ITA) at RWTH Aachen University and its partners AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR with “StoneBlade – Lightweight construction with granite for the wind industry”. This innovation enables manufacturers to reduce the amount of non-recyclable materials used in rotor blade construction. At the same time, it reduces the weight of these components and improves the mechanical properties relating to the stability of wind turbines. The innovative approach replaces glass-fibre reinforced plastic in the blade components with hard rock – a natural, cost-effective and recyclable lightweight material. The slabs of rock are cut and ground to a thickness of just a few millimetres and embedded in a fibre composite laminate with carbon fibre, which stabilises them for alternating load cases. The pre-stressed material is pressure-stable in the composite and can absorb tensile forces in the event of continuously alternating loads without any loss of stiffness.

Third place went to the Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK) with its partner Mercedes Benz AG for the interdisciplinary development of a highly integrated inductive charging module for electric vehicles. The ultra-thin charging module was designed to make optimum use of space in the vehicle underbody without reducing ground clearance. An interdisciplinary approach was adopted for the development process. This involved the electrical, mechanical and process characterisation of high-frequency Litz wires, ferromagnetic foil and metal wire cloth as well as the creation of a simulation model. The result is a demonstrator for a charging system with a structural height of 15 mm and a total weight of 8 kg. It achieves a transmission efficiency of up to 92 percent at 7.2 kW nominal power and active air cooling. The hardware demonstrator was fabricated in a 3-step process using RTM and VARI techniques.

Overview of all the winners in the three categories:
Category “Innovative Products/Applications”
1st Place: “Traffic signs from Nabasco (N-BMC)” – Nabasco Products BV and Lorenz Kunststofftechnik GmbH, partners: Pol Heteren BV and NPSP BV
2nd Place: “Novel, ultratough vinyl ester resin for the construction of large marine vessels” Evonik Operations GmbH
3rd Place: “Air intake housing with a multi-material design for gas turbines” – MAN Energy Solutions SE, Leichtbau-Zentrum Sachsen GmbH and Leichtbau-Systemtechnologien KORROPOL GmbH.
Category “Innovative Processes”
1st Place: “In-mould wrapping” off-tool, film-coated, fibre composite components for exterior applications – BMW Group, Partner: Renolit SE
2nd Place: “Adaptive automated repair of composite structural components in the aviation sector” – Lufthansa Technik AG, Partner: iSAM AG
3rd Place: “Automated surface pre-treatment using VUV excimer lamps” – CTC GmbH
Category “Research and Science”
1st Place: “Bondline Control Technology (BCT)” – German Aerospace Center (DLR)
2nd Place: “StoneBlade – Lightweight construction with granite for the wind industry” – Institute of Textile Technology at RWTH Aachen University, Partners: AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR
3rd Place: “Interdisciplinary development of a highly integrated inductive charging module for electric vehicles” – Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK), Partner: Mercedes Benz AG

Submissions for the next Innovation Award can be made from the end of January 2022.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

24.11.2021

PERFORMANCE DAYS cancelled in Munich on December 1-2, 2021

  • Focus now on digital fair platform

The PERFORMANCE DAYS team regrets having to cancel at short notice the physical edition of PERFORMANCE DAYS which was scheduled to take place on December 1-2, 2021 at the Messe München exhibition center. Right up until today, the event organizers of PERFORMANCE DAYS were in the final stages of preparations for the fair. The goal of being able to realize a fully booked fair with a portfolio like in pre-pandemic times seemed to be within reach. The political regulations agreed in Bavaria from November 19, 2021 and the heavily restricted constraints associated with an incidence of 1000 have far-reaching consequences for PERFORMANCE DAYS. As a result of the current sharp rise in the number of infections in Munich, the planned winter edition must now be cancelled as a precaution. The focus now is now completely on the digital fair on December 1 and 2, 2021.

  • Focus now on digital fair platform

The PERFORMANCE DAYS team regrets having to cancel at short notice the physical edition of PERFORMANCE DAYS which was scheduled to take place on December 1-2, 2021 at the Messe München exhibition center. Right up until today, the event organizers of PERFORMANCE DAYS were in the final stages of preparations for the fair. The goal of being able to realize a fully booked fair with a portfolio like in pre-pandemic times seemed to be within reach. The political regulations agreed in Bavaria from November 19, 2021 and the heavily restricted constraints associated with an incidence of 1000 have far-reaching consequences for PERFORMANCE DAYS. As a result of the current sharp rise in the number of infections in Munich, the planned winter edition must now be cancelled as a precaution. The focus now is now completely on the digital fair on December 1 and 2, 2021.

The new measures are scheduled to come into effect in Munich from the middle of this week, which would lead to very short-term changes. The organizers of PERFORMANCE DAYS therefore see themselves in the responsibility to enable a minimum of planning security as well as a responsible handling of the given situation with this decision.

“Exceptional situations require exceptional decisions – making these all the more difficult. After experiencing a very successful and surprisingly well-attended fair with the Functional Fabric Fair by PERFORMANCE DAYS in Portland, Oregon last week, we have tried everything possible up to the last moment and firmly believed that we would finally set a further positive milestone with the physical edition of PERFORMANCE DAYS in Munich. We fulfilled all the requirements, updated our hygiene concept several times to comply with the dynamically changing measures and took all the necessary precautions for a safe event. Unfortunately, current developments do not allow us to host the trade fair event next week, since the undisputed top priority is the protection and health of our visitors. Now our focus turns to the full implementation of the Digital Fair on December 1 and 2, 2021”, explains Marco Weichert, CEO of PERFORMANCE DAYS

Focus on digital platform
The PERFORMANCE DAYS team is now investing all its efforts into implementing the Digital Fair on December 1 and 2, 2021. As part of THE LOOP, those interested have the opportunity as of now to view online the fabric innovations and news for the Winter Season 2023/24, this year’s Focus Topic “Sustainable Nylon” and the latest color trends. In the Marketplace, visitors will be able to view the numerous exhibitor products, including the PERFORMANCE FORUM’s curated sustainable fabric highlights. In order to present the fabrics to visitors as realistically as possible in terms of feel, design and structure in digital form, the PERFORMANCE FORUM has been equipped with new 3D-technology, including innovative tools such as 3D images, video animations and downloadable U3M files. Throughout the Digital Fair, exhibitors and fair visitors can look forward to extensive networking opportunities. For example, as part of the extensive digital supporting program on December 1, with various expert talks, discussion rounds and speakers via livestream, moderated by Charles Ross live from the studio. On December 2, the “sustain & innovate” conference on this year’s Focus Topic “The Sustainable Future of Nylon” will kick off with discussions and panels, moderated by Astrid Schlüchter, Editor-in-Chief of SAZsport and SPORTSFASHION by saz.  

A very special thank you goes out to the entire PERFORMANCE DAYS community with its exhibitors, visitors and partners for their active support, trust, loyalty and understanding in these still extraordinary times. The team looks forward to the Digital Fair on December 1 and 2, 2021 and further ahead to meeting you all personally on April 27 and 28, 2022 at the summer edition of PERFORMANCE DAYS live in Munich.

Source:

Performance Days

(c) NRW.Energy4Climate
Minister Pinkwart zur Carbon Management Strategie NRW
23.11.2021

Fraunhofer UMSICHT: Carbon Management Strategie NRW

Zahlreiche Produkte unserer Industriegesellschaft wie Stahl, Aluminium, Zement oder Kunststoff bestehen aus Kohlenstoff oder benötigen ihn, um hergestellt werden zu können. Zentrale Ansätze, wie der Umgang mit Kohlenstoff neu und nachhaltig gestaltet werden kann, hat das Ministerium für Wirtschaft, Innovation, Digitalisierung und Energie (MWIDE) mit der Carbon Management Strategie NRW vorgelegt. Ziel ist eine klimaneutrale Industrie. Auf einer gemeinsamen Veranstaltung des Thinktanks IN4climate.NRW und des MWIDE hat Wirtschafts- und Energieminister Prof. Andreas Pinkwart mit Expert*innen aus Industrie, Wissenschaft und Zivilgesellschaft die Inhalte diskutiert.

Zahlreiche Produkte unserer Industriegesellschaft wie Stahl, Aluminium, Zement oder Kunststoff bestehen aus Kohlenstoff oder benötigen ihn, um hergestellt werden zu können. Zentrale Ansätze, wie der Umgang mit Kohlenstoff neu und nachhaltig gestaltet werden kann, hat das Ministerium für Wirtschaft, Innovation, Digitalisierung und Energie (MWIDE) mit der Carbon Management Strategie NRW vorgelegt. Ziel ist eine klimaneutrale Industrie. Auf einer gemeinsamen Veranstaltung des Thinktanks IN4climate.NRW und des MWIDE hat Wirtschafts- und Energieminister Prof. Andreas Pinkwart mit Expert*innen aus Industrie, Wissenschaft und Zivilgesellschaft die Inhalte diskutiert.

»Für uns ist klar: Kohlenstoff kann Klimaschutz«, so Minister Pinkwart. »Mit unserer Carbon Management Strategie zeigen wir ganz konkret, wie eine klimaneutrale Kohlenstoffwirtschaft in Nordrhein-Westfalen aussehen kann. Wir wollen Kohlenstoff nicht nur reduzieren, sondern auch nachhaltig so oft wie möglich im Kreislauf nutzen und die Gesellschaft transparent einbinden. Wir sind damit das erste Bundesland überhaupt, das sich dem Thema annimmt. So können wir unsere ehrgeizigen Klimaschutzziele erreichen und den Industriestandort von morgen gestalten.«

Eine klimaneutrale Industrie braucht nachhaltige Kohlenstoffquellen
Dr. Iris Rieth, Projektmanagerin für Kohlendioxidwirtschaft und Circular Economy bei IN4climate.NRW: »Eine klimaneutrale Industrie braucht nachhaltige Kohlenstoffquellen. Die Circular Economy und die Nutzung von CO2, dessen Ausstoß nicht vermieden werden kann, müssen wir weiter ausbauen. IN4climate.NRW hat in enger Zusammenarbeit mit Unternehmen und der Wissenschaft wichtige Ansätze erarbeitet, die den unterschiedlichen Industrieprozessen gerecht werden. Die Carbon Management Strategie führt nun die Bausteine der Transformation zusammen und setzt die notwendigen politischen Leitplanken, an denen wir uns in unserer weiteren Arbeit orientieren können.«
Infrastruktur für den Transport von CO2 muss aufgebaut werden

Kohlenstoffdioxid war bislang kein Bestandteil von Infrastrukturplanungen in Deutschland. Dabei wird es auch in Zukunft Prozesse geben, bei denen unvermeidlich CO2 entsteht, wie etwa bei der Herstellung von Zement. Verschiedene Projekte arbeiten bereits daran, CO2 direkt am Ofen abzufangen und anderen Branchen, vor allem der chemischen Industrie, als Rohstoff zur Verfügung zu stellen (engl. Carbon Capture and Utilisation, CCU). Eine Infrastruktur für den Transport muss jedoch erst noch aufgebaut werden.

Konkrete Optionen, wie ein solches Pipeline- und Transportsystem aussehen könnte, hat IN4climate.NRW Mitte Oktober in dem Diskussionspapier »CO2 in einer klimaneutralen Grundstoffindustrie« veröffentlicht. In einem weiteren Diskussionspapier »Circular Economy in der Grundstoffindustrie« hat IN4climate.NRW zudem aktuelle Stoffströme analysiert und Lösungsansätze für eine zukünftige industrielle Circular Economy erarbeitet. Beide Papiere sind maßgeblich in die Carbon Management Strategie des Landes eingeflossen.

An der Paneldiskussion haben neben Wirtschafts- und Energieminister Prof. Andreas Pinkwart teilgenommen:

  • Dr. Iris Rieth, Projektmanagerin für Kohlendioxidwirtschaft und Circular Economy bei IN4climate.NRW,
  • Prof. Görge Deerberg, stellvertretender Institutsleiter des Fraunhofer UMSICHT,
  • Dr. Christoph Sievering, Head of Global Energy and Climate Policy & Site Transformation bei Covestro,
  • Arne Grotenrath, Experte für Treibhausgasbilanzierung bei Germanzero sowie
  • Michael Theben, Abteilungsleiter Klimaschutz im Ministerium für Wirtschaft, Innovation, Digitalisierung und Energie.
Source:

Fraunhofer UMSICHT

(c) ANDRITZ
ANDRITZ Laroche textile recycling line
22.11.2021

ANDRITZ at Techtextil India 2021

International technology group ANDRITZ will present its innovative nonwovens and textile technologies at the booth of its Indian representative PRN Techtex at Techtextil India 2021 in Mumbai, India, from November 25 to 27, 2021. A special focus will lie on its technologies for air-through bonding, needlepunch, textile recycling, and processes for biodegradable wipes, like spunlace and WetlaceTM.

Air-through Bonding
Air-through-bonding lines are the preferred choice for producing nonwovens with the best quality of softness and bulk for acquisition distribution layers, top sheets, and back-sheet products. With ANDRITZ carding machines and the new flat belt oven, customers benefit from high-performance fabrics from 16 to 80 gsm, produced with bicomponent fibers. Several Chinese customers have already invested in ANDRITZ aXcess carding machines, which provide perfect web uniformity. In addition, the CETI (European Center for Innovative Textiles) in Lille, France, has installed an air-through-bonding oven from ANDRITZ.

International technology group ANDRITZ will present its innovative nonwovens and textile technologies at the booth of its Indian representative PRN Techtex at Techtextil India 2021 in Mumbai, India, from November 25 to 27, 2021. A special focus will lie on its technologies for air-through bonding, needlepunch, textile recycling, and processes for biodegradable wipes, like spunlace and WetlaceTM.

Air-through Bonding
Air-through-bonding lines are the preferred choice for producing nonwovens with the best quality of softness and bulk for acquisition distribution layers, top sheets, and back-sheet products. With ANDRITZ carding machines and the new flat belt oven, customers benefit from high-performance fabrics from 16 to 80 gsm, produced with bicomponent fibers. Several Chinese customers have already invested in ANDRITZ aXcess carding machines, which provide perfect web uniformity. In addition, the CETI (European Center for Innovative Textiles) in Lille, France, has installed an air-through-bonding oven from ANDRITZ.

Textil-recycling Technologies
Recently, ANDRITZ acquired Laroche SAS, a leading supplier of fiber processing technologies such as opening, blending, dosing, airlay web forming, textile waste recycling, and decortication of bast fibers. The product portfolio further complements and increases the ANDRITZ Nonwoven product range. One focus of this product range lies on complete recycling lines for post-consumer and industrial textile waste to produce fibers for re-spinning and/or nonwoven end uses.

Needlepunch Technologies
Driven by the dynamic market for durable nonwovens, ANDRITZ has developed an elliptical pre-cylinder tacker – the PA3000. With this modern machine, ANDRITZ is responding to customer demands for higher capacities and lighter products. The PA3000 is an optimized cylinder pre-needleloom, which offers greater speeds and widths and has been specially developed for lighter webs. There is no friction between the web and the rolls, and there are no issues with the visual appearance.

ANDRITZ is also focusing on its latest needling technology for producing veloured felts, mainly for applications in the automotive industry.

In addition, ANDRITZ will be presenting the next generation of its batt-forming technology, the ProWin system. ProWin is a further development of ProDynTM and ProWidTM, which have achieved a high level of acceptance on the market with around 200 systems installed. This technology improves the current weight-profiling options and increases the actual production capacity.

Production of Bio-Wipes
For many years now, ANDRITZ has offered different nonwoven processes, such as spunlace and Wetlace, with one goal in mind: reduction and elimination of plastic raw materials while maintaining the high quality of the desired product properties. The latest development in this field is the ANDRITZ neXline wetlace CP line. This is a fully engineered production line, combining the benefits of wetlaid and drylaid technologies to produce a new generation of biodegradable wipes. This process achieves high performance entirely with plastic-free raw materials. The added benefit of using a blend of fibers, like wood pulp, short-cut cellulosic fibers, viscose, cotton, hemp, bamboo, or linen, without chemical additives, results in a 100% sustainable fabric.

(c) Hochschule Reutlingen. Von links nach rechts: Dieter Herrmann, Prof. Dr. Jochen Strähle, Prof. Dr. Ulrich Scholze, Prof. Dr. Hendrik Brumme (alle Hochschule Reutlingen), Dipl.-Ing. (FH) Peter D. Dornier, Wolfgang Schöffl und Zaim Goganov (M.Sc.) (alle Lindauer DORNIER GmbH).
19.11.2021

Hochmoderne, neue Webmaschine für die Fakultät Textil & Design

Die Firma Lindauer DORNIER GmbH spendete der Fakultät Textil & Design der Hochschule Reutlingen eine neue Hochleistungs-Luftdüsenwebmaschine. Das Familienunternehmen mit Sitz in Lindau am Bodensee zählt weltweit zu den Technologieführern im Bereich Textilmaschinenbau.

Die gespendete Maschine verfügt über die hochmoderne, patentierte Antriebstechnik und ist eine wertvolle Ergänzung des weltweit einzigartigen Maschinenparks der Fakultät Textil & Design im Bereich der textilen Lehre. Inhaber und Geschäftsführungsvorsitzender, Dipl.-Ing. (FH) Peter D. Dornier, übergab “das Geschenk“ persönlich und betonte dabei, die seit Jahrzehnten und bereits zu Zeiten der Gründung der Lindauer DORNIER GmbH in den 50er-Jahren bestehende, vertrauensvolle Partnerschaft mit der Fakultät Textil & Design und deren Vorgängerorganisationen.

Studierende der Fakultät Textil & Design erhalten an der neuen Luftwebmaschine Praxis-Unterricht auf dem neuesten Stand der Technik.

Die Firma Lindauer DORNIER GmbH spendete der Fakultät Textil & Design der Hochschule Reutlingen eine neue Hochleistungs-Luftdüsenwebmaschine. Das Familienunternehmen mit Sitz in Lindau am Bodensee zählt weltweit zu den Technologieführern im Bereich Textilmaschinenbau.

Die gespendete Maschine verfügt über die hochmoderne, patentierte Antriebstechnik und ist eine wertvolle Ergänzung des weltweit einzigartigen Maschinenparks der Fakultät Textil & Design im Bereich der textilen Lehre. Inhaber und Geschäftsführungsvorsitzender, Dipl.-Ing. (FH) Peter D. Dornier, übergab “das Geschenk“ persönlich und betonte dabei, die seit Jahrzehnten und bereits zu Zeiten der Gründung der Lindauer DORNIER GmbH in den 50er-Jahren bestehende, vertrauensvolle Partnerschaft mit der Fakultät Textil & Design und deren Vorgängerorganisationen.

Studierende der Fakultät Textil & Design erhalten an der neuen Luftwebmaschine Praxis-Unterricht auf dem neuesten Stand der Technik.

Das Schussgarn wird mittels Luftstrahl ins Webfach eingetragen. Eine Technik, die insbesondere bei hohen Schusseintragsfrequenzen elektronische Regelungen für Luftdrücke und Blaszeiten der Luftdüsen im Millisekundenbereich für einen stabilen Maschinenlauf und eine hohe Gewebequalität erfordert. Die Webmaschine verfügt über die weltweit einzigartige und patentierte Antriebstechnik DORNIER SyncroDrive®. Zwei servogeregelte Motoren sorgen hier für den separaten Antrieb von Webmaschine und Fachbildeeinrichtung mit elektronischer Synchronisierung. Das Ergebnis ist die Minimierung der Gleichlaufschwankungen und die Schwingungsreduktion und damit die Maximierung der Konstanz der Gewebequalität.

Die konsequente, konstruktive Umsetzung physikalisch-technischer Zusammenhänge wird in dieser Maschine an einer Vielzahl von Einzelheiten erfahrbar und begreifbar. Damit wird die Theorie aus der Vorlesung in idealer Weise eindrücklich unterstützt und ergänzt.

In einer, nach aktuellen Verordnungen, klein gehaltenen Feierstunde brachten der Präsident der Hochschule Reutlingen, Prof. Dr. Hendrik Brumme und der Leiter des Fachgebiets Weberei, Prof. Dr.-Ing. Ulrich Scholze der Firma Lindauer DORNIER den Dank für die Spende zum Ausdruck. Dipl.-Ing (FH) Peter D. Dornier wünschte sich in seiner kurzen Rede eine interdisziplinäre Nutzung der Webmaschine durch Textiltechnologie sowie Design-Studierende und zeigte die vielversprechenden Chancen der Textiltechnologie für die Gestaltung einer nachhaltigeren Zukunft auf.
Die großzügige Spende ist ein Meilenstein in der langjährigen Beziehung zwischen der Fakultät Textil & Design und der Firma DORNIER, deren Inhaber sich auch als Stiftungspräsident der Walter-Reiners-Stiftung stark für den textilen Nachwuchs engagiert.

Ergänzt wurde die Spende der Webmaschine mit dem von der Kuenzel GmbH, Münchberg, kostenlos überlassenen Webblatt, sowie der gestifteten Webkette und Schussgarne durch die Zweigart & Sawitzki GmbH & Co.KG, Sindelfingen.

Source:

Hochschule Reutlingen

(c) evo
Christian Basler wurde zum neuen Vorstandsvorsitzenden des UMSICHT-Fördervereins gewählt und tritt die Nachfolge von Bernd Homberg an
16.11.2021

UMSICHT-Förderverein unterstützt Forschungsprojekte

Jedes Jahr unterstützt der Förderverein des Fraunhofer UMSICHT zwei Projekte mit einer Anschubfinanzierung. Die finanzielle Starthilfe ebnet den Weg, um vielversprechende Forschungsvorhaben zeitnah zu realisieren. Sein Engagement um den wissenschaftlichen Nachwuchs unterstreicht der Verein mit der Prämierung herausragender Bachelor- und Masterarbeiten. Die diesjährigen Auszeichnungen erfolgten im Rahmen der gestrigen Mitgliederversammlung, auf der evo-Vorstand Christian Basler als neuer Vorstandsvorsitzender des Fördervereins gewählt wurde.

Jedes Jahr unterstützt der Förderverein des Fraunhofer UMSICHT zwei Projekte mit einer Anschubfinanzierung. Die finanzielle Starthilfe ebnet den Weg, um vielversprechende Forschungsvorhaben zeitnah zu realisieren. Sein Engagement um den wissenschaftlichen Nachwuchs unterstreicht der Verein mit der Prämierung herausragender Bachelor- und Masterarbeiten. Die diesjährigen Auszeichnungen erfolgten im Rahmen der gestrigen Mitgliederversammlung, auf der evo-Vorstand Christian Basler als neuer Vorstandsvorsitzender des Fördervereins gewählt wurde.

Der UMSICHT-Förderverein ist ein wichtiger Partner des Oberhausener Forschungsinstituts und verfügt über ein großes Netzwerk aus Politik, Wirtschaft und Industrie. Neben der Verleihung des UMSICHT-Wissenschaftspreis ist die gezielte Nachwuchs- und Projektförderung ein zentrales Anliegen des mittlerweile über 30 Jahre bestehenden Vereins. So werden auf der jährlichen Mitgliederversammlung Menschen ausgezeichnet, die innovative Projekte bearbeiten und besondere Arbeit geleistet haben. In diesem Jahr erhielten die UMSICHT-Forschenden Laura Huwald und Tobias Rieger eine finanzielle Zuwendung von je 10 000 Euro für ihre Forschungsvorhaben. Die beiden Studentinnen Sonja Frerich und Hannah Brenner freuten sich über insgesamt 750 Euro Preisgeld für ihre herausragenden Bachelor- und Masterarbeiten.

Neuartige Brennstoffzellen
Laura Huwald, Abteilung Elektrochemische Energiespeicher, untersucht die »Entwicklung und Charakterisierung kohlenstoffbasierter poröser Transportlagen für Brennstoffzellen«. Dank der Substitution durch kohlenstoffbasierte Materialien kann das neuartige Zellkonzept mittels kostengünstiger und langzeitstabiler Komponenten realisiert werden. Ihre Arbeit bietet die Grundlage zur Initiierung eines Nachfolgeprojekts mit Industriebeteiligung, in dem ein Prototyp des neuartigen Brennstoffzellenkonzepts mit den am Fraunhofer UMSICHT entwickelten Bipolarplatten realisiert werden soll.

Innovative Recyclingverfahren für Kunststoffabfälle
Tobias Rieger überprüft im Projekt SubForceH2 das »Chemische Recycling von Kunststoffabfällen zur Substitution fossiler Rohstoffe in der chemischen Industrie und der Erzeugung von Wasserstoff«. Dadurch können z. B. CO2-Emissionen eingespart werden, da der in Kunststoffabfällen gebundene Kohlenstoff nicht durch konventionelle Müllverbrennung freigesetzt, sondern durch die Umsetzung zu chemischen Grundstoffen im Kreislauf gehalten wird. Als Nebenprodukt entsteht zudem Wasserstoff, welcher in zahlreichen industriellen Anwendung benötigt und zur Speicherung von Energie zunehmend an Bedeutung gewinnt.

Masterarbeit: Kunststoffe in Böden
Im Rahmen ihrer Masterarbeit »Entwicklung, Validierung und Anwendung einer Methode zur Untersuchung von Kunststoffemissionen auf landwirtschaftlichen Nutzflächen« entwickelte Hannah Brenner eine praxisorientierte Methode, mit der Bodenproben nach ihrer Entnahme auf dem Feld aufbereitet und hinsichtlich ihres Mikroplastikgehalts analysiert werden können. Ziel ist die Einschätzung der Belastung von Feldflächen durch Kunststoffemissionen und der anschließende Vergleich mit anderen Habitaten. Dadurch soll eine schnellstmögliche Reduzierung des Mikroplastikeintrags in terrestrische Ökosysteme erreicht werden.

Herausragende Bachelorarbeit
Hauptbestandteil von Sonja Frerichs Bachelorarbeit war es, die mechanische Eignung eines neuartigen, am Fraunhofer UMSICHT entwickelten Materials für den Einsatz in Brennstoffzellen zu untersuchen. Im Fokus stand die Umformbarkeit von thermoplastbasiertem Folien-BPP (BPP: Blasextrudiertes Polypropylen), um Gasverteilungsstrukturen für Wasserstoff und Sauerstoff einprägen zu können. Die Vermessung der eingeprägten Strukturen wurde unter anwendungsnahen Bedingungen durchgeführt.

Source:

Fraunhofer-UMSICHT

(c) Deutsche Lichtmiete
15.11.2021

Deutsche Lichtmiete: Nachhaltige Beleuchtungssanierung für IGEFA WEINBRENNER

Energie effizient nutzen – diese Mission verfolgt die IGEFA WEINBRENNER Energy Solutions GmbH mit einer Vielzahl von Innovationen. Als einer der führenden Hersteller von Wärmetauschern konzentriert sich das Handeln des Unternehmens dabei längst nicht nur auf die Wirksamkeit der angebotenen Systeme, sondern auf den gesamten Herstellungsprozess. Das betrifft auch vermeintliche Nebenschauplätze wie die Beleuchtung der Produktionshallen. Nach einer umfassenden Beleuchtungssanierung nutzt IGEFA WEINBRENNER – ebenso wie andere Unternehmen der ZILONIS Gruppe – nicht nur energie- und kostensparende LED-Technik, sondern auch das innovative Light as a Service Konzept der Deutschen Lichtmiete.

Energie effizient nutzen – diese Mission verfolgt die IGEFA WEINBRENNER Energy Solutions GmbH mit einer Vielzahl von Innovationen. Als einer der führenden Hersteller von Wärmetauschern konzentriert sich das Handeln des Unternehmens dabei längst nicht nur auf die Wirksamkeit der angebotenen Systeme, sondern auf den gesamten Herstellungsprozess. Das betrifft auch vermeintliche Nebenschauplätze wie die Beleuchtung der Produktionshallen. Nach einer umfassenden Beleuchtungssanierung nutzt IGEFA WEINBRENNER – ebenso wie andere Unternehmen der ZILONIS Gruppe – nicht nur energie- und kostensparende LED-Technik, sondern auch das innovative Light as a Service Konzept der Deutschen Lichtmiete.

„Als Hersteller von Produkten der Wärme- und Verfahrenstechnik wissen wir, wie wichtig effiziente und kostensparende Systeme in einer zukunftsorientierten Industrie sind“, sagt Musa Smakaj, Geschäftsführer von IGEFA WEINBRENNER. Nachhaltigkeit mitzudenken bestimmt hier sämtliche interne und externe Prozesse auf dem Weg zu maßgeschneiderten, kundenspezifischen Lösungen. „Unser Ziel ist, die CO2-Emissionen unserer Kunden anhaltend zu reduzieren“, so Smakaj und verweist auf eine Vielzahl von Forschungsprojekten bei ZILONIS, bei denen Themen wie Wasserstoffproduktion, Fernwärmeanbindung und Solarstrom im Mittelpunkt stehen.

 

Source:

Deutsche Lichtmiete / HARTZKOM

(c) Fibre Extrusion Technology
11.11.2021

FET hails INDEX20 impact

Fibre Extrusion Technology, UK is celebrating a successful INDEX20 nonwovens exhibition in Geneva, Switzerland, which closed on 22 October. Although the company has a long history in supplying meltspinning equipment for the nonwovens sector, this represents its first venture at a dedicated nonwovens show.
 
FET’s Managing Director, Richard Slack explains. “Techtextil and ITMA have previously been our main exhibitions of choice, but INDEX20 was an ideal vehicle for FET to launch our new laboratory scale spunbond system, which enables client development of nonwoven fabrics in a number of formats and polymers.”
 
FET already has spunbond systems in the field, including composite systems which utilise both spunbond and meltspun functions. The growth in global nonwovens technology, partly driven by demand for pandemic-related materials, is forecast to continue.
 

Fibre Extrusion Technology, UK is celebrating a successful INDEX20 nonwovens exhibition in Geneva, Switzerland, which closed on 22 October. Although the company has a long history in supplying meltspinning equipment for the nonwovens sector, this represents its first venture at a dedicated nonwovens show.
 
FET’s Managing Director, Richard Slack explains. “Techtextil and ITMA have previously been our main exhibitions of choice, but INDEX20 was an ideal vehicle for FET to launch our new laboratory scale spunbond system, which enables client development of nonwoven fabrics in a number of formats and polymers.”
 
FET already has spunbond systems in the field, including composite systems which utilise both spunbond and meltspun functions. The growth in global nonwovens technology, partly driven by demand for pandemic-related materials, is forecast to continue.
 
“We were delighted with the response at INDEX”, continued Richard Slack. “There was considerable interest shown in the new spunbond system and its potential for lab scale innovation. It’s clear that the industry is seeking new alternatives to synthetics at the moment, and our technology is able to assist with the testing and assessment of many of the new feedstocks being pioneered in this extremely inventive sector, where everyone is suddenly talking and cooperating with everyone else, regardless of whether they are generally competitors. We recorded in excess of 20 serious enquiries from totally new contacts and sectors, including blue chip companies in the hygiene, medical and packaging industries.”
 
“There were initial concerns about projected attendance figures, especially from China and USA companies, but we experienced good footfall from key decision makers, especially those from Europe. It was encouraging to at last experience the opportunity for face-to-face contact with old and new customers on a large scale and we are now starting to reap the benefits with enquiries continuing to flow in”.

Source:

Fibre Extrusion Technology

Photo: Messe Frankfurt
08.11.2021

Techtextil India: Hybrid exhibition in November

India’s leading trade fair in technical textiles, nonwovens and composites, Techtextil India, is ready to make a comeback through its hybrid edition launch from 25 – 27 November 2021. With a series of live product demonstrations, insightful knowledge sessions and B2B networking opportunities, the multimodal trade fair will provide a strong avenue for technical textile professionals to reimagine their business potential.
 
After a successful grand edition in 2019, Techtexil India is all set to return for the very first time since the pandemic. The three-day exhibition will be hosted in a hybrid format from 25 – 27 November 2021, Bombay Exhibition Centre, Goregaon which will unite technical textile players from across its varied application areas. Top technical textile brands including JB Ecotex, PARK Nonwoven, Loyal Textiles Lenzing, Mehala, Meera Industries, amongst many others will showcase their latest products at the hybrid fair. Moreover, leading German brands exhibiting at Techtextil India 2021 will be hosted under the German pavilion.

India’s leading trade fair in technical textiles, nonwovens and composites, Techtextil India, is ready to make a comeback through its hybrid edition launch from 25 – 27 November 2021. With a series of live product demonstrations, insightful knowledge sessions and B2B networking opportunities, the multimodal trade fair will provide a strong avenue for technical textile professionals to reimagine their business potential.
 
After a successful grand edition in 2019, Techtexil India is all set to return for the very first time since the pandemic. The three-day exhibition will be hosted in a hybrid format from 25 – 27 November 2021, Bombay Exhibition Centre, Goregaon which will unite technical textile players from across its varied application areas. Top technical textile brands including JB Ecotex, PARK Nonwoven, Loyal Textiles Lenzing, Mehala, Meera Industries, amongst many others will showcase their latest products at the hybrid fair. Moreover, leading German brands exhibiting at Techtextil India 2021 will be hosted under the German pavilion.

The conjunction between the physical exhibition and the online business matchmaking platform will make way to a wider range of networking. Local and international visitors who are unable to attend the venue will be able to witness the exhibition virtually through the ‘MFI virtual app’ which will host live knowledge sessions and product demonstrations for visitors. The two-day multimodal trade fair allows the visitors to search for specific products like fibers, yarns, nonwovens, machinery, coated textiles with easy-to-use filters further to which they can share their query or connect directly with the respective exhibitors.

At the same time, visitors attending the venue will be welcomed under a well-organised physical exhibition following the government-authorised safety protocols of ‘MFI SafeConnect’. These protocols will enable visitors to engage in secure face-to-face interactions with exhibitors and witness the latest technical textile technologies and innovations in-person.

Alliance with the Government of Tamil Nadu
In a bid to strengthen indigenous production through the state and attract investors, the nodal agency for investment promotion and facilitation for the Government of Tamil Nadu – Guidance has signed up for Techtextil India 2021. Furthermore, technical textile players from Tamil Nadu such as Cyber Textiles India Pvt Ltd, Jayashree Spun Bond, Lenzing Ag India, Liester Technologies, Loyal Textile Mills Ltd, Milltex Engineers Pvt Ltd, Superfil Products Pvt Ltd, Uster Technologies (India) Pvt Ltd have also confirmed their participation for the exhibition.
Announcing a close co-operation with Messe Frankfurt India for the 2021 edition, Ms Pooja Kulkarni, IAS MD & CEO, Guidance Tamil Nadu, stated: “While there are several inherent advantages for the growth of technical textiles in Tamil Nadu specifically, many raw materials used in the production of sanitary products, artificial ligaments, seat belt webbings, airbags are still heavily imported. In this context, the alliance with Techtextil India Forum can help us reduce import dependency and bring investments in R&D, manufacturing, innovation by partnering with global technical textiles companies.”

With 50% of India’s textile mills in Tamil Nadu and complementary clusters of knitting, weaving and medical devices manufacturing in Coimbatore, and Tiruppur, the region provides immense opportunities for Meditech investments. Two petrochemical and refinery units – One in Cuddalore and another in Nagapattinam by CPCL is in the process of being established in Tamil Nadu. These units will enable availability of MMF raw material for the textile industry across the state. Hence, manufacturing in Tamil Nadu can be a win-win arrangement for investors as India provides access to the burgeoning market as well.

International expertise with German pavilion
Techtexil India 2021 edition will feature an exclusive German Pavilion showcasing products and technologies from top German manufacturers, including Autefa Solution Germany GmbH, DILO Systems GmbH, Emtec Electronic GmbH, Georg Sahm GmbH & Co, Karl Mayer Verwaltungsgesellschaft mbH, Merz Maschinenfabrik GmbH and Oerlikon Barmag Zweigniederlassung der Oerlikon Textile GmbH & Co.

Source:

Messe Frankfurt (HK) Ltd