From the Sector

At ITMA 2019 in Barcelona from June 20-26th, Goller will introduce the new Knit Merc for achieving the highest quality mercerization of knitted fabrics at the lowest tension and with under 3% variation in dimensional stability with high grade fabrics, for perfect dyeing results every time.

Mercerization is an essential textile finishing step for all cotton and cellulosic fibre-based fabrics in order to improve dye uptake and tear strength while reducing fabric shrinkage and imparting a silk-like lustre to the materials.

The Knit Merc is the result of intensive R&D developments at Goller and follows the successful introduction to the market of the company’s Sintensa Cyclone drum washing compartments for achieving the highest washing efficiency at the lowest tension.

The Knit Merc being exhibited at ITMA 2019 can accommodate 8.4 metres of fabric in its impregnation compartment and a further four metres in its first chain section to achieve a production speed of 25m/min at 30 seconds dipping time.

It is designed for dry-on-wet mercerizing, either cold or hot, and is equipped with an inlet combination of scroll and slat rollers for fabric guidance, a Tandematic uncurler in front of a rubberized de-airing roller and a grooved 320mm bottom roller with 320mm and 600mm perforated upper drums.

It benefits from automatic tension regulation and the low liquor content is ensured by the integrated lye tank and automatic circulation and filtration units.

An 8-ton high efficiency squeezer is stationed at the exit before the chain section and a 5-ton squeezer at the exit of the chain field.

Further fabric control and stability is provided by a cast iron pin chain with automatic optical and mechanical sensors, the Tandematic uncurler, an overfeed device and a driven belt arrangement for fabric support.

Following its successful beginnings in summer 2018 and its expansion in January 2019, TRADE UNION will be developed yet further as a dedicated space for selected brands and agencies.
 
“TRADE UNION is very close to our hearts,” explains SEEK Director Maren Wiebus. “Being able to work together to fill a space with life, interact with customers and products, and tell authentic stories in a laid-back, relaxing atmosphere – this open-minded, collaborative approach is ultra-modern and of the minute in its simplicity. We are all in the same big boat and can consider ourselves lucky that colleagues and customers are and have become friends. Together, we can achieve a lot this way.”

It has always been integral to SEEK’s DNA to continually work with partners and friends to develop new concepts that are perfectly suited to the demands of the market. The carefully curated setting of TRADE UNION, featuring brands such as Eat Dust, Porter-Yoshida & Co and Knickerbocker, is especially popular with the top buyers.
 
Felix Engelmann has supported the concept right from the off through his marketing agency Haptiques, and is full of passion and on board again with the concept this season.
“The TRADE UNION concept really came off for us in January. We worked well with our partners; the vibe was positive and nicely relaxed. I’m expecting the atmosphere in the summer to be just as fantastic and I’m sure it’ll be a good occasion with friends, partners and employees.”
 
In July, buyers can look forward to an expanded portfolio including Red Wing Shoes, a brand from Minnesota. European Marketing Manager Rik van Dijk comments:
“We can't wait to attend the inspiring setting, because our buyers really feel at home there. We need a location where you can take a step back, find a quiet place to sit and talk to everyone. The extra space at the TRADE UNION guarantees this. We’ve only heard good things from friendly brands and we’re really looking forward to the trade show.”

Research and restoring of ancient tradition to shape a denim style which is always cutting-edge, focusing on a 100% Italian supply chain and on the outstanding quality of materials and processes.

“Ciao Milano”, the new edition of the Denim Première Vision show, for the first time in Milan (28-29 Maggio 2019), includes among its protagonist the project signed by Paolo Gnutti, aka PG DENIM. The company, under Gnutti’s creative guidance, has restyled its proposals, with two clear objectives in mind: on the one hand expanding its presence on the high-end denim market, focusing more and more on a bespoke approach and on product innovation, on the other side the ambitious goal of manufacturing one million metres of fabric in the year 2019.

This path of constant research is combined with a totally integrated and 100% Italian manufacturing structure, in order to give the market not just new products, but also new “tools”, says Paolo Gnutti, R&D Head at PG DENIM:
“We are targeting the market section where production always requires thinking out of the box, which feeds the imagination of those who are asked to transform it. Our approach is often made of provocations, suggestions, reflections, through continuous research which leads us to designing frequent and always innovative capsule collections”.

A creative input which almost always results from situations and pathways which bring back the creativity of
PG DENIM, to rediscover techniques and processes of the great Italian and international tailoring tradition.

The last frontier of innovation in racing suits made with yarns in Metamicro is the model Prime SP-16+, designed in collaboration with the Team McLaren Honda F.1

The spinning mill Filidea, joint venture between Marchi & Fildi spa and Abalıoğlu Holding A.Ş specialized in technical and high performance yarns with natural and synthtic fibers, is parter of Sparco, italian Company leader for the production of automotive components and technical apparels for the most important world Championships. The cooperation between the two Companies located in Piedmont, northern Italy, is focused on the supply of yarns with Metamicro in an exclusive composition, that are used for the production of the racing suits Sparco of the Premium range for Formula 1 and the World Rally Championship. The fire resistant yarn Metamicro based on aramidic fibers are a product of the latest generation, for their production it is necessary a special spinning line. The production is following the strict Sparco standards. Sparco controls all the production chain of racing suits, from Filidea, who has the competence to dye all the yarns with aramidic fibers in its own dyeing plant, to the woven fabric, produced and dyed in its own plant, to the woven fabric made by the italian Company TAT, till the production of garments. The process is always improved and tested.

Metamicro yarns are made by an high peformance spinning process. They are used for the production of fire resistant fabrics, that make a protection barrier for the body against flames and high temperature. The very fine micronage allows the production of very light fabrics with thick texture, the perfect base for light and comfortable suits. These features assure easier movements to the driver and the maximum protection from fire, keeping high breathability.

Filidea has invested on its production capacity of corespun yarns with XLANCE® technology, fiber used for the production of longlasting workwear apparel with an excellent fitting.

The spinning mill Filidea, joint venture between Marchi & Fildi spa and Abalıoğlu Holding A.Ş specialize in technical and high performance yarns with natural and synthtic fibers, is increasing its production of blends with XLANCE®.

XLANCE® is the innovative elastolefin fibe, elastic, chlorine and UV resistant. It finds application on workwear and outdoor clothing, with natural and comfort fitting. The comfort stretch feature follows the the body’s natural movement during the day-to-day work. Workwear clothing are so light, resistant and with a contemporary look. Resistance to abrasion and to frequent industrial laundry cycles with chemical products meet the needs of several professional sectors. XLANCE® is produced by ©Xlance srl, Company located in Varallo Pombia (province of Novara – Piedmont – Italy) that found in Filidea the perfect partner for the development of specific yarns, that are getting more and more requested. An innovation that is getting more important thanks to the cooperation of the two textile Companies located in Piedmont. Filidea has been producing XLANCE® yarns since 2009 and has now a great know-how. The Company to strengthens its leadership in technical yarns, for the main applications on protetictive garments, workwear, sportswear, racing and automotive. Filidea has developed and consolidated several partnerships for the creation of complete supply chains and the collaboration with ©Xlance is a perfect example.

For the cooperation with Lidl within the project “Biodegradable textiles with prints” the CHT Group developed innovative recyclable textile print products.

These Lidl textiles are produced with CHT print pastes and pigments and were certificated by the internationally active consulting institute EPEA GmbH - Part of Drees & Sommer according to the Cradle to Cradle Certified™ Gold Standard. With this pilot project the companies demonstrate their sense of responsibility for people and the environment as well as their commitment in the field of circular economy.

According to the Cradle to Cradle approach, shortly C2C, products shall merge into a biological or technical cycle after the end of their life cycle. This re-use helps prevent waste and save raw materials. The impact on the environment and health of all of the ingredients of C2C textiles is already tested in the design stage and during manufacturing. C2C experts additionally ensure a gapless control of the manufacturing processes. They check the chemicals in use, make sure that the water is kept clean and that renewable energies are used. Since this control affects the complete textile supply chain, it guarantees absolute transparency.

The CHT Group can now offer high quality and sustainable substitutes for common textile print pastes with its first biodegradable print pastes and pigments.

wear2wear is an innovative industrial partnership dedicated to high-quality and sustainable clothing. Five expert partners in Europe have come together to cover the entire recycling loop. On cutting-edge production systems, textile fibres from used clothing will be turned into functional fabrics. Schoeller Textil AG is supplying a wholistic textile portfolio for the workwear area. At Schoeller Textil, the recyclable, functional fabrics from the wear2wear concept belong to the Inspire fabric group. These are high-quality protective workwear fabrics made of 100 percent polyester, which offer the greatest clothing comfort and often feel just like cotton. They are also compliant with the stringent requirements of the bluesign® system.

The sustainable wear2wear concept is synonymous with high-quality, responsible clothing. In European operations, textile fibres from used garments are used to produce new functional fabrics. Depending upon the area of intended use, they also meet strict waterproofing, breathability, protection and comfort requirements. To ensure that the raw material cycle comes full circle, these textiles can be recycled again when they reach the end of their service life. As a result, there is no waste, and they go on to produce new garments. As the wear-2-wear partner companies guarantee that – from the quality of the raw materials to the guaranteed recycling end process – these are 100 percent recyclable, functional fabrics made of recycled textile fibres. Water- and dirt-repelling technologies based on renewable raw materials, along with the most advanced membrane technology, will ensure that the textiles are manufactured and impregnated entirely without the use of PFC in the future too.

Five partner companies  
The five European partner companies in the wear2wear cooperation cover the entire recycling loop. Heinrich Glaeser Nachfolger GmbH is a German fibre and yarn producer and the “recycler” in the loop. Märkischen Faser GmbH (D) is the “upcycler” and fibre manufacturer. Carl Weiske GmbH & Co. KG (D) develops the polymers, fibres, yarns, chemical additives and textile systems, and TWD Fibres GmbH (D), a fully-integrated filament yarn producer, covers the entire range of polyester and polyamide 6.6 continuous filament yarns. Schoeller Textil AG, the innovative Swiss company, is responsible for textile production and manufactures sustainable high-tech fabrics with maximum clothing comfort. The matching climate-neutral and similarly 100 percent recyclable PTFE and PFC-free membrane, as well as recycled outer materials and linings, are supplied by Sympatex Technologies (D), the ecological alternative among the textile function specialists. DutchSpirit is a Dutch company which has been dedicated to environment-friendly clothing since 2010. Its mission is to significantly increase the awareness for sustainable clothing and offer recyclable clothing in the workwear segment. DutchSpirit is the initiator for the development of the Inspire products from Schoeller Textil and provided the inspiration for the wear2wear concept. Further garment-making partners who now also belong to the cooperative group include: Anchor Workwear BV (NL), Hüsler Berufskleider AG (CH), Groenendijk Bedrijfskleding BV (NL), Bedrijfskledingdiscounter BV (NL) and Rifka'S (NL).

Govier plans to scale the organization and take customer focus to the next level to drive growth
Kornit Digital, (NASDAQ: KRNT), a global market leader in digital textile printing technology, announced today that Chris Govier has been named Managing Director at Kornit Digital Europe GmbH.

Govier is a proven leader who brings broad experience of supporting customers with industrial digital transformation, a proven record of driving growth, and solid experience building and managing world class teams. In his new role, Govier will oversee Kornit Digital’s operations in Europe, the Middle East and Africa (EMEA) and will be instrumental in scaling up Kornit’s business.

Govier previously served in sales and general management roles at Xerox Corporation, and holds a BA from the University of Wellington, New Zealand.

Commenting on the appointment, Gilad Yron, Kornit Digital’s Executive Vice President of Global Business, said, “I welcome Chris on board as the new Managing Director of Kornit Digital Europe. He brings with him solid experience in the analog-digital transition in industrial print and deep regional understanding. Europe has traditionally been a strong performer for Kornit, and Chris’ expertise will help us grow the organization to the next level.”

“This is an incredibly exciting time to join Kornit Digital – their technology, coupled with a passion and drive will significantly disrupt the textile printing industry.” said Chris Govier. “EMEA represents a huge opportunity and I look forward to building on the fantastic success achieved so far.”

Paper Converting Machine Company (PCMC), part of Barry-Wehmiller, received the prestigious Technical Innovation Award from the Flexographic Technical Association (FTA) for its recently introduced SteadyPrint print-stabilization technology. This award was presented May 5, 2019, at the FTA Forum 2019 awards banquet held in New Orleans.

SteadyPrint, now part of PCMC’s Fusion and ELS Max flexographic presses, couples innovative patented mechanical designs with cutting-edge disturbance-cancelling algorithms that suppress disturbances associated with the hard edge, largely removing the impact of bounce in flexographic printing. The press automatically learns when the disturbance occurs on each job and implements the cancellation algorithm to minimize or eliminate the impact on print quality.

“We are extremely excited to be a recipient of the 2019 FTA Technical Innovation Award,” said Rodney Pennings, PCMC’s Printing, Coating and Laminating Sales Director. “The entire PCMC team has worked very hard in developing SteadyPrint over the past couple of years. It is an innovation that we are quite proud of, and we appreciate the accolades that showcase SteadyPrint within the package-printing industry. Winning this award in the year we are celebrating our 100-year anniversary is also incredibly meaningful.”

First showing of game-changing technology at a European tradeshow includes the recently launched Kornit Atlas, Kornit Avalanche Poly Pro and Kornit Presto
Kornit Digital (Nasdaq: KRNT), a worldwide market leader in digital textile printing technology, has announced details of its corporate presence at Fespa 2019 which will take place in Munich, Germany, May 14-17.

Kornit’s exhibit will focus on the game-changing technology that was unveiled in the beginning of the year and will now be on display for the first time in a tradeshow in Europe: the Kornit Atlas and the Kornit Avalanche Poly Pro. The presence will be complemented by a Kornit Storm HD6, a direct-to-fabric sample area featuring prints from Kornit’s upcoming Presto system and an installation of Colorgate’s Textile Production Server for Kornit.

The Kornit Atlas is a heavy-duty system created for super-industrial garment decoration businesses. It is designed to deliver a typical annual production capacity of up to 350,000 impressions, optimizing production efficiency and cost of ownership. The Kornit Atlas is aimed at highly productive garment decorators, mid to large size screen printers and innovative businesses looking to combine state-of-the art technology with lowest cost of ownership, making it easier than ever to address the requirements of leading and mid-sized brands, as well as new generation digital brands. The Kornit Atlas uses water-based Kornit NeoPigmentTM Eco-Rapid Inks which are eco-friendly, GOTS approved and OEKOTX certified, and serve as the main driver of the retail quality prints.

• Clean Technology. Smart Factory.

Remscheid – Oerlikon invites all visitors to this year's ITMA in Barcelona on a journey into the future of manmade fiber production. From 20 to 26 June 2019, the world market leader will show all its guests its vision of a sustainable and automated manmade fiber production in a virtual 4D showroom at its 1,000 m² stand in Hall 7, A101: "Clean Technology. Smart Factory." is the motto of the future. And this is only a stone's throw away from reality at the stand. Because today Oerlikon is presenting four world premieres for efficient machine and plant concepts in a new, innovative industrial design. Together with numerous other innovations, all this forms the new DNA of the Oerlikon Manmade Fibers segment.

The challenges for the manmade fiber industry are manifold and Oerlikon shows its customers solutions:

1. Choosing the right business model
Price pressure on fiber and yarn manufacturers is growing due to global market consolidation. Here it is important to position oneself correctly. Are you producing polyester, nylon or polypropylene for the niche market and skimming off good margins with innovative products and ingenious material properties, or are you looking for business success through economies of scale in the volume market such as the constantly growing apparel sector? Oerlikon has the right answers for both business models. And the most important thing: the market leader supplies all solutions from a single source. See for yourself at the world premieres of the machine and system concepts of WINGS FDY PA6, BCF S8 Tricolor and the revolutionary eAFK Evo texturing machine.

2. Finding alternatives for good personnel
Finding good operators in the manmade fiber industry is becoming increasingly difficult, even in emerging industrial nations such as China, India and Turkey. The solution is obvious. What, for example, the automotive industry achieved years ago with the 3rd Industrial Revolution is now also taking its course in the textile industry. And at the same time it is even shifting up a gear. In the next step, automation in combination with digitization will lead to new, sustainable production. Oerlikon will be showing how automation and digitization interact at ITMA. Self-learning machines and systems, artificial intelligence (AI), remote services and edge computing are just a few of the key words in the digital half of the new Oerlikon Manmade Fibers DNA.

3. Guarantee quality and traceability
The qualities of the fibers and yarns must meet the highest demands and their production must be traceable throughout the textile value chain. This no longer only plays an important role in the automotive industry, where safety is of paramount importance. Other branches of industry that use fibers, yarns and nonwovens also want to know where the raw materials they produce for consumer articles come from. Legal regulations are demanding this more and more frequently. Oerlikon offers optimal solutions with its DIN ISO certified manufacturing processes. More than half of the world's manmade fiber producers are convinced every day that the qualities produced on Oerlikon Barmag, Oerlikon Neumag and Oerlikon Nonwoven equipment are right – and all visitors to ITMA can do the same on site.

4. Efficient and sustainable production
In the future, the materials produced from manmade fibers must become part of a further improved global recycling economy. The recycling of polyester – with over 80% market share the most frequently used manmade fiber in the world – has not only been on the agenda since today. Oerlikon already has solutions at hand: from PET bottles to fibers and filaments, to textiles and carpets. ITMA is the next step. With the VacuFil® Oerlikon in cooperation with the subsidiary company BBEngineering presents the world premiere No. 4 – a recycling solution within a running polyester production with a waste-free approach.

Vision becomes reality
The Oerlikon Manmade Fibers segment thus demonstrates what the ITMA in Barcelona promises as the world's leading trade fair for textile machinery and plant construction: "Innovating the world of textiles – sourcing for a sustainable future". In Hall 7, A101, this is already reality.