From the Sector

An impairment charge has become necessary based on the current status of the new 5 year plan.

(Market Abuse Regulation N° 596/2014)
•    Impairment loss amounting to €80-100 million in the fourth quarter 2020 in the business unit CFM
•    Restructuring program resolved with savings target of more than €100 million until 2023
•    Guidance 2020 for Group sales and operating recurring Group EBIT confirmed
•    Guidance 2020 for net result reduced to minus €130-150 million

In the current status of the 5 year plan, which is at present under preparation, significant deviations have already become apparent today, particularly in the market segments Automotive, Aerospace and Wind Energy in the business unit Composites – Fibers & Materials (CFM). Partially also due to the pandemic, Automotive and Aerospace is developing slower than anticipated in the last 5 year plan. In contrast, business with Wind Energy is growing much stronger than previously planned. These changes in the product mix lead to lower mid-term earnings at CFM compared to the prior 5 year plan. Following these deviations from the last 5 year plan, an event-driven impairment test was undertaken. This results in a non-cash impairment charge amounting to €80-100 million, which will be recorded in the fourth quarter 2020.

The Board of Management of SGL Carbon SE today also resolved the implementation of a restructuring program, with which the Company is targeting savings of more than €100 million until 2023 (compared to the base year 2019). These savings consist of a planned socially compatible reduction in personnel of more than 500 employees and substantial reduction in indirect spend, particularly in the areas of travel, consulting and external services. Costs of approximately €40 million are anticipated for the implementation of this restructuring program. A little more than half of this is expected to be recorded as expenses in the fourth quarter 2020, while the associated cash outflows are mainly forecasted for 2021.

This requires a partial adjustment of the guidance for 2020. The solid operational development in the third quarter 2020 with Group sales between €220 and €230 million and operating recurring EBIT1 between €13 and €15 million (plus approximately €9 million positive one-time effects) is within the framework of our expectations for the full year 2020. However, the Group net result is likely to develop below the prior year level of minus €90 million and reach approximately between minus €130 and €150 million due to the restructuring provisions as well as the impairment charge (prior guidance: improvement to a negative low double-digit million € amount).

With liquidity of €167 million as of September 30, 2020 (compared to €137 million at year-end 2019) and further cash inflows in the fourth quarter 2020 from successfully implemented additional funding measures, the Company’s position is solid. This liquidity is more than sufficient for the payment of the purchase price for SGL Composites USA in the amount of USD 62 million at the end of 2020 as well as the restructuring-related cash outflows expected mainly in 2021. The Company continues to have access to the revolving credit facility (RCF) in the amount of €175 million, which remains undrawn.

The quarterly statement as of September 30, 2020 will be published on November 12, 2020 as scheduled. Further details on the new 5 year plan as well as the guidance on the fiscal year 2021 will be presented with the publication of the Annual Report 2020 on March 25, 2021.

*The use of KPIs in this notification is aligned to the annual report 2019 and the interim report for the first half year 2020. There were no changes to the scope of consolidation or to valuation methods compared to the previous guidance.

The collaboration between Tonello and denim designer Piero Turk gave birth to a sustainable denim collection, result of a combination of the latest responsible technologies, and created with the most eco-friendly fabrics selected by The Kingpins Show.

“When it comes to working on new developments, we always start from new ideas and the constant research that starts from a concept that becomes reality, by increasingly raising the bar of sustainability,” said Alice Tonello, R&D and Marketing Director of Tonello.

18 exclusive and contemporary denim pieces, result of the premium experience of Piero Turk, and Tonello with its new brand-new finishing process: The Laundry (R )Evolution.

This is a radically new conception thought to simplify and optimize the entire garment finishing process.

It involves only 2 technologies in the entire finishing cycle, reducing waste and optimizing resources: LaserBlaze, and The All-in-One-System. Finally we use Metro, our software that processes real data, in real time to check all laundry consumption, optimizing processing times and improving performance.

The All-in-One System performs all washing operations by integrating 4 sustainable technologies into a single machine: ECOfree 2, which uses ozone in both the water and air; NoStone® for authentic and pumice-free stone-wash effects; UP, for washing processes with at least 50% less water; Core, a nebulizing system improving performance and reducing water consumption.

As a result of The Laundry (R )Evolution, Tonello developed two innovative and patent-pending processes: OBleach and Wake.

OBleach is the new Tonello process, which, by using only ozone, “returns to the future” with an authentic, sustainable and cool Bleach. Without chemicals.
This is possible thanks to a combination of the technologies part of our All-In-One System.
In short, the real Bleach without Bleach has finally arrived. And this in the year of the total ban of permanganate too.

Wake is the first totally natural dyeing system that uses only plants and biodegradable vegetable waste like flowers, berries and roots, without harmful chemicals additives.

The capsule collection will be displayed at KINGPINS24 on October 27th during the seminar held by Alice Tonello and Piero Turk.

As reported on August 17, 2020, the Supervisory Board of SGL Carbon SE had appointed Thomas Dippold to CFO and member of the Board of Management of SGL Carbon SE effective December 1, 2020. Fortunately, Mr. Dippold is able to assume office of his mandate as member of the Board of Management of SGL Carbon SE earlier, so that the Supervisory Board of the company has brought forward the appointment to October 15, 2020, also to prepare for the planned assumption of the CFO position.

As previously reported, and effective December 1, 2020, Mr. Dippold is succeeding the long-standing CFO Dr. Michael Majerus, who is resigning from his office effective November 30, 2020 by mutual amicable consent.

As planned, Dr. Stephan Bühler resigned from his office as member of the Board of Management effective October 15, 2020.

Two ISKO I-SKOOL™ 7 looks make their debut at the Graduate Fashion Foundation, part of London Fashion Week, a springboard for new talent striving to bridge the gap between education and industry.

Following an unprecedented academic year, GFF celebrates how the Class of 2020 have adapted and overcome adversity to complete their degrees across 26 fashion specialisms, from Design and Knitwear to Comms, Marketing and Business. London, 17-22 September – To bring together fashion educators and industry leaders and to support their graduates to reach their full potential once they have graduated: this has always been GFF’s main goal for the past 28 years. Now more than ever, GFF continues in its long-standing commitment to share good practice and knowledge and to inspire students to become innovators, environmental leaders, employees, and educators while promoting cultural diversity and inclusivity within an international platform – very much in keeping with ISKO I-SKOOL™ values and approach which resonate throughout the contest’s Denim Awards.

Designers Kotryna Adomaityte and Isabel Hambly from Nottingham Trent University were 2 of the 9 winners of the ISKO I-SKOOL™ 7 Awards, announced in a phygital ceremony held on July 22. The two students were invited to showcase their winning creations at GFF. Kotryna, winner of the ISKO I-SKOOL™ PERICOLO Award by Cadica Group, impressed the audience with her “Wild West Denim” look to London at the GFF Showroom.

Isabel Hambly, winner of the ISKO I-SKOOL™ Best Marketable Product, stole the show with her “Women at war” outfit which was displayed at the Catwalk Show, live-streamed from Samsung KX on September 22. That two of ISKO I-SKOOL™ 7 winners and finalists were part of this important event is proof of the significant role the contest – developed and supported by ISKO – plays in nurturing and championing talent and creativity. This edition’s main concept was world’s citizenship, with the Creative Theme “North, East, South, West – connected by one planet”. The twenty shortlisted finalists were asked to dig into their roots and to approach different cultures, defining and tracking down the geography of the world connecting them through responsibility. In addition to exploring the planet both locally and globally, they were also required to take into account the product life cycle of their outfits – featuring a 5-pocket jeans to interpret their view on the “local” concept and two Denim Show Pieces to reflect their worldwide influences and topics of interest. These were made with top ISKO™ denim fabrics, meeting the designers’ needs and providing a strong sustainable ingredient.

“We are really proud that two of our winners made it to GFF, with which we have many values in common – it marks another important step in their journey” said ISKO Senior Executive ISKO I-SKOOL™ Project Irem Orhun. “All of this goes to show how ISKO I-SKOOL™ plays a fundamental role in providing the foundation to enter the industry more aware of your skills and capabilities.”

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

A new standard in pure white, 100% clean and fault-free textile substrates has been demanded by this market in recent years due to the rapid growth in digitally-printed banners and billboards – often referred to as ‘soft signage’.

The substrates of choice for digital printing are 100% polyester warp knits which are resilient and allow excellent take-up of inks, and vibrant colours and clear and precise images to be achieved with digital printing techniques. The knitted construction also has the advantage of elasticity, which is a plus in terms of flexibility for installers.

Critically, the warp knitted fabrics have extremely smooth surfaces which is becoming increasingly important due to the general move away from PVC coatings which were the standard in the past.

It was to finish these fabrics for Georg and Otto Friedrich GmbH as well as providing such services for many other customers, that the GtA plant in Neresheim, Baden-Württemberg, was established in 2015.

The purpose-built plant on a greenfield site was initially equipped with a fully-automated, 72 metre long Monforts installation comprising a washing machine integrated with a 3.6 metre wide, seven-chamber Montex stenter. The line quickly went from single to double shift production and then to 24/7 operation  to meet demand.

Expanded widths

Building on the success of this installation, GtA has now installed two more Montex stenter lines – both in expanded working widths of 5.6 metres and purpose-built at Montex GmbH in Austria.

A six-chamber Montex unit is combined with a washing machine to guarantee the purity of the substrates, while a five-chamber line is integrated with a wide-width coating machine. This new coating capability at GtA has led to a number of new additions to the Georg and Otto Friedrich DecoTex range for digital printing, including wide width fabrics with flame retardant, antimicrobial and non-slip finishes.

The new Montex stenter lines benefit from all of the latest innovations from Monforts, including the Smart Sensor system for the optimised maintenance planning of key mechanical wear components on the stenters. A comprehensive overview of the condition of all parts at any time is now available for operators within the highly intuitive Qualitex visualization software.

With Qualitex, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

Environmental commitment

GtA is run by a seasoned team of textile professionals led by Managing Director Andreas Niess.

“We have received excellent service from Monforts from the outset and we were happy to place the order for these two new lines as part of our ongoing cooperation,” he says. “With all of the latest Monforts advances in technology we are fully in control of all production and quality parameters with these lines, as part of our significant commitment to innovative environmental technology.”

The GtA plant, which operates in near-cleanroom conditions, has also been equipped with proprietary technology to fully exploit the Monforts air-to-air heat recovery systems that are now standard with Montex stenters.

“Around 30 per cent of our investment volume at the site goes to energy-saving measures and we are sure that this commitment is worthwhile,” Mr Niess says. “As an example, our integrated heat recovery system fully exploits the waste heat from the process exhaust air and the burner exhaust gases of the Monforts stenters, allowing us to achieve an exhaust air temperature of  between 30 to 34°C, compared to what would conventionally be between 140 to 160°C. Another focus has been on exhaust air purification technology and here too, the latest technology has been installed with integrated heat recovery elements.”

This, he adds, saves 52% of the energy that would normally be used – equating to 5,800,000 KwH per year. The necessary audits for energy-efficient companies are also carried out annually.

In addition, GtA has purpose-designed the automatic chemical mixing and dosing systems that feed the padders for the key treatments that are carried out on the fabrics through the stenters.

The company is going further, however, in its pursuit of clean production and raw materials.

"We want to be an asset and not a burden on our immediate environment and therefore do not use any additives containing solvents," Mr Niess says. “We were the first to use fully halogen-free flame retardant chemistry, and we use bio-based, finely ground alumina products for the washing process instead of surfactants. PES polyester yarns made from recycled material are also increasingly used and the latest additions to our raw materials portfolio, the RC-Ocean products, are made from recycled sea plastic.

“We are now planning a combined heat and power plant for the production of electrical energy and heat and we will also build a photovoltaic system that converts solar radiation into electrical energy. GtA wants to be the first textile finishing company to be CO2-neutral in the manufacture of all of its products by 2025. The complete heat supply and heating for the 13,000 square metre production hall, as well as the office building and the hot water supply for the domestic water, is already energy-neutral. We are convinced that this commitment will pay off in the long term and our positive business development proves that sustainability and business profitability are perfectly compatible.”

In addition to the products for Georg and Otto Friedrich GmbH, GtA  offers its manufacturing capacities for other customers as a contract service.

All products are manufactured in accordance with Öko-Tex Standard 100, product class 1 and the company is also involved in the research and development of new sustainable manufacturing processes, in cooperation with many regional universities and funding project partners.

• Schleswig-Holstein Minister President visits Neumünster, Germany

Since the outbreak of the coronavirus pandemic, the worldwide demand for protective masks and apparel has resulted in a record number of new orders in the high double-digit millions of euros at the Oerlikon Nonwoven business unit of the Swiss Oerlikon Group. From the manufacturing site in Neumünster, Germany, the high-tech meltblown systems – with their patented ecuTE+ nonwovens electro-charging technology – are meanwhile be exported all over the world. For the very first time, a contract has now been signed with a business in Australia. Today, Schleswig-Holstein’s Minister President Daniel Günther was won over on site by the technology of a ‘global player’. Rainer Straub, Head of Oerlikon Nonwoven, was thrilled, stating: “The machines and systems for manufacturing manmade fiber and nonwovens solutions from Neumünster enjoy an outstanding reputation throughout the world. It is especially in this crisis that the technology from Schleswig-Holstein has proven itself to be absolutely world-class.”

In addition to a tour of the meltblown system and its assembly and production facilities, the visit by Minister President Daniel Günther had one purpose above all: the dialog between politicians and business. Rainer Straub, Head of Oerlikon Nonwoven, and Matthias Pilz, Head of Oerlikon Neumag, jointly expressed their thanks for the support that Oerlikon has repeatedly had the fortune to experience over the past months and years in Schleswig-Holstein and looked to the future full of hope. “As a result of our additional investment at the site here in Neumünster – be this in our new technology center that will be completed by the end of this year or in our new logistics center that is already operating – we, as one of the region’s largest employers, are continuing to move forward, supported by a State Government that is also focusing on both promoting industry and business and on advancing an efficient training and educational system, as innovation is only possible with outstanding engineers”, stated Matthias Pilz. And Rainer Straub directed his appeal specifically at the Minister President: “Treat education and training as a priority. Ultimately, they will secure the future of Schleswig-Holstein as a center of excellence and manufacturing!”

Five-million-euro digitalization program

Daniel Günther, the incumbent Minister President of Schleswig-Holstein since 2017, immediately responded, making reference to one of the Federal State’s current training initiatives: “The State Government is supporting higher education institutions and students in the present coronavirus crisis. With a five-million-euro digitalization program, we are investing on the long-term digitalization of our higher education institutions. With this, we are overall creating a future for young people, particularly also for those who could very well go on to invent the next generation of manmade fiber systems.” And the Minister President was just as impressed by the willingness and readiness with which Oerlikon has been providing high-level support since the beginning of the COVID-19 pandemic to master the present challenges as he was with the company’s meltblown technology itself. Rainer Straub explained: “When, at the beginning of the pandemic in February, demand for protective face masks increased rapidly, we at Oerlikon Nonwoven responded immediately. We ramped up all the available production capacities here in Neumünster in order to quickly manufacture nonwovens for producing face masks using our laboratory systems. As a result, we have been able to make a small, regional contribution to covering demand. In parallel, we have pulled out all the stops in order to systematically further expand our skills as machine and system builders so as to cater to the initially expected, and now also continuing, global demand for meltblown systems as quickly as possible.”

Leading meltblown technology

The Oerlikon Nonwoven meltblown technology – with which nonwovens for protective masks can also be manufactured, among other things – is recognized by the market as being the technically most efficient method for producing highly-separating filter media made from plastic fibers. The capacities for respiratory masks available in Europe to date are predominantly manufactured on Oerlikon Nonwoven systems. “Ever more manufacturers in the most diverse countries are hoping to become independent of imports. Therefore, what we are experiencing in Germany is also happening in both industrialized and emerging countries throughout the world”, commented Rainer Straub. In addition to China, Turkey, the United Kingdom, South Korea, Austria and numerous countries in both North and South America, Australia and not least Germany will for the first time also be among the countries to which Oerlikon Nonwoven will be delivering machines and equipment before the end of 2021.

• Diana, Giusy, Simona and Marina. The call to action of the fashion world was born from four women engaged in the field of sustainability. On the occasion of Fashion Revolution Week, we tell you their story and the results achieved

A task force of Italian textile companies active in our area supported the first call to action launched at the fashion world by four women who have always been involved in the field of sustainability. The appeal launched on March 19th by the green journalist Diana de Marsanich, Giusy Bettoni, founder and CEO of C.L.A.S.S. (Creativity Lifestyle and Sustainable Synergy)the eco multi-platform hub specialized in integrating a new generation of eco values into fashion, products and companies, Simona Roveda, Editorial Director and Director of Institutional Communication of LifeGate and Marina Spadafora, Italian Country Coordinator of Fashion Revolution and currently collaborating with Luxury Fashion Brands to implement responsible strategies in their companies have luaunched a call-to-action project which has brought together textile companies to manufacture PPE garments for the medical staff working in San Gerardo Hospital in Monza, near Milan.

The companies that answered the call-to-action are: Filo d’Oro, Mantero, ROICA™ by Asahi Kasei, C.L.A.S.S. (Creativity Lifestyle and Sustainable Synergy) e Zerobarracento, Iluna Group, Lg Electronics, Jimmy Lion, Personal Genomics, Isamar Holyday Village, Marcolin Eyewear, Maglificio Ripa.

During the last weeks the 4 women collected about 1,800 non-drip cotton and non-woven TNT gowns for sanitary use, about 400 protective masks for multipurpose washable, bacteriostatic, breathable and water-repellent prevention, 1,000 washable cotton surgical caps, 150 complete protective googles eye masks, two microwave ovens for hospital departments to offer support to medical and healthcare personnel by helping them in the few breaks during the grueling shifts of this period, a supply of samples of cotton socks, 300 cotton masks + polyester outer layer, water-repellent and antibacterial, and free weekly stays made available to doctors, nurses, civil protection personnel and families with related children involved in the Covid-19 pandemic.

Amid the rapid spread of COVID-19 around the world, DyStar’s global operations continue to adapt to the development of the situation and to mitigate potential risks or impacts across the business. While the trajectory is unknown, DyStar is guided by recommendations from the World Health Organization and the local government authorities, to proactively address situations that could possibly affect our people and customers. This is to ensure that we have effective plans and standard procedures to minimize the disruption of our global operations.

Business Continuity Plan (BCP)
As a globally operating company, each of our operating sites, manufacturing plants, offices have a Business Continuity Plan (BCP) in place to sustain our operations and the supply chains we serve. The BCP, owned by our Business Continuity Management Team, provides clear guidance for all local operations, such as Administration, Customer Services, Finance, Logistics Services, Sales and Technical Support as well as Procurement, to enable all functions to continue operating effectively to serve our customers, distributors and agents.

Emergency Response Plan (ERP)
DyStar’s manufacturing sites are also installed with an Emergency Response Procedure to cover all emergency circumstances, including the COVID-19 pandemic disease. The goal of the emergency response procedure is to mitigate the impact of such events on people and the environment, ensuring operational readiness of the site during an emergency.

As the world adjusts to the impact of the COVID-19 pandemic, DyStar will continue to monitor the situation very closely and will provide updates that adapt to the changing situation. We remain committed to provide our customers with excellent service and to work closely with all our partners throughout this difficult period.

HeiQ, winner of the Swiss Technology Award and Swiss Environmental Award, launches HeiQ Viroblock NPJ03, an antiviral and antimicrobial textile treatment that is tested effective against coronavirus.

Since its inception 15 years ago, HeiQ has forged a solid innovation track record helping brands improve textile products. Catalyzed to action by the global fight against Coronavirus, HeiQ launches HeiQ Viroblock NPJ03, an antiviral and antimicrobial textile treatment which is proven effective against human coronavirus (229E) in face mask testing, significantly enhancing the antiviral log reduction from 2.90 of untreated face masks to 4.48, over 99.99% reduction of virus infectivity. (Remarks: a log reduction of 2 is equivalent to 100 times the effectiveness).

Chinese protective masks producer Suzhou Bolisi is the lead adopter of HeiQ Viroblock NPJ03. Treated masks will be available on the market as early as this April. American legwear manufacturer Kayser-Roth is planning to add the technology to their new product, Ghluv hands protector, while Lufeng from China is evaluating the technology on other types of fabric used for garments.

HeiQ Viroblock NPJ03 is a unique combination of vesicle and silver technologies designed to inhibit the growth and persistence of bacteria and viruses. The HeiQ vesicle technology targets lipid- enveloped viruses, such as coronavirus, providing rapid virus deactivation, while the HeiQ silver technology inhibits the replication of both bacteria and viruses. HeiQ Viroblock NPJ03 can be applied to a wide spectrum of textile surfaces including face masks, air filters, medical gowns, curtains, drapes and more. HeiQ also has a range of highly wash-durable antimicrobial and odor control textile technologies, called HeiQ Pure, combining silver-based and bio-based materials for all fabric types.

Sateri has scored ‘A-‘ in CDP (formerly Carbon Disclosure Project) for Climate Change in 2019, placing it at Leadership band and the top 27% of companies in its sector, for implementing current best practices. And making Sateri World’s First Viscose Producer to Reach Leadership Band

This is the first time Sateri has participated in this annual voluntary reporting. It is also the first time that a viscose producer has reached Leadership band. Sateri attained an ‘A’ for more than half of the 11 categories that it was assessed for, including value chain engagement, Scope 1,2,3 emissions, and governance. Its ‘A-‘ overall score is higher than the ‘C’ average globally, in Asia, and in the Textiles and Fabric Goods sector; no companies in the same sector scored ‘A’.

Allen Zhang, President of Sateri, said, “We are very pleased to achieve such a commendable score on our first attempt at CDP reporting. It is a validation of our efforts and actions to combat climate change and our contribution towards decarbonising the textile industry. The CDP platform not only helps us measure and benchmark our sustainability performance against more than 8,400 companies globally, but also serves as a management tool for continuous improvement.”

Sateri has made great strides in the last year on emission reduction work. In June 2019, Sateri and the China National Textile and Apparel Council (CNTAC) jointly launched the EcoCosy® Climate Leadership Programme. The programme invites Sateri’s value chain partners to participate in the Climate Stewardship 2030 Initiative to set a decarbonisation pathway for the fashion industry to reduce the industry’s GHG emissions by 30% by 2030. Results of the first phase of the programme were published in the EcoCosy® Climate Leadership Whitepaper 2020, which was shared at COP25 in Madrid last year.