From the Sector

CO₂ as renewable carbon source
Carbon is the main element in numerous materials used in industrial processes and in our daily lives. It is currently mostly provided from fossil sources. But what if carbon could be used directly from CO₂ emissions? Biotechnology shows particularly great potential for the eco-effective conversion of climate-damaging CO₂ emissions into valuable basic chemicals. A consortium of 12 partners investigated this pathway in the EU-funded BioRECO₂VER project, examining the conversion of CO₂ emissions from refineries and the cement industry into the chemical building blocks isobutene (C₄H₈) and lactate (C₂H₆O₃).

Innovative chemo-enzymatic concept for CO₂ Capture
Project partner Luleå University of Technology (LTU) focused on the first process step of capturing and concentrating CO₂ from industrial point sources. Their team developed a hybrid chemo-enzymatic process consisting of a novel solvent blend and an ultrastable carbonic anhydrase (CA) enzyme. The solvent blend included an amino acid ionic liquid and a tertiary amine and displayed a good compromise between enzyme compatibility, absorption rate, capacity and desorption potential. In addition, LTU generated ultrastable enzyme mutants that showed 50% increased resistance to selected flue gas inhibitors compared to the original CA. This 3-component CO₂ capture process was scaled up in a pilot rig, and the set-up further used for real off gas pre-treatment in the project.

Two unique pilots for biotechnological CO₂ Conversion/Utilization
The biotechnological conversion of (captured) CO₂ and the co-substrate hydrogen by microorganisms poses technical and economic challenges because it takes place in the liquid phase and the substrates are gases which are poorly soluble. The BioRECO₂VER project investigated two approaches to address this: fermentation under elevated pressure and bio-electrochemistry with in situ production of hydrogen.

Pressurized fermenter
Project coordinator VITO designed a flexible and multifunctional high-pressure fermenter, customized for research activities with advanced online sensors, monitoring and control, and also including a membrane filtration unit to achieve high concentrations of the microbial biocatalysts. The set-up was broadly tested in the BioRECO₂VER project both with pure CO₂ and CO₂-rich off-gases but can also be used for investigations involving other poorly soluble gases, such as methane, oxygen, or synthesis gas. Pressures up to 10 bar can be applied.

First solely CO₂-based bio-electrochemical platform
University of Girona designed and tested a bio-electrochemical platform. The key differentiators of the pilot plant are:

• Two parallel lines to test engineered strains and bio-electrochemical systems
• Fully automated pilot plant capable to control key operational parameters (pCO₂, pO₂, pH₂, pH, Temperature) to intensify the process performance
• Solid-liquid separation unit (membrane) to recover the planktonic cells and return them into the bio-electrochemical systems.

This unique infrastructure will be used beyond the project to support further research and development activities in the broad area of CO₂ capture and conversion.

The Hygiene Division of Indorama Ventures Public Company Limited (IVL) is pleased to announce that two of its manufacturing sites have achieved International Sustainability Carbon Certification Plus Certification.

FiberVisions’ Varde site in Denmark, a polypropylene fiber producer, and Avgol’s Uzlovaya site in Russia, a spunlaid nonwovens producer, satisfied audits related to traceability and the reasonable use of biomaterials.

Shachar Rachim, CEO, IVL Hygiene Division, part of IVL’s Fibers business segment, said: “This accreditation underscores our commitment to support our customers to achieve their carbon dioxide reduction targets through using carbon neutral fibers. The certification is assurance that our nonwoven fabrics and fibers meet all the ISCC’s demanding standards for recycled-renewable materials. Our certified facilities can trace the product’s composition through the supply chain, without needing to requalify the materials.”

IVL expects that the ISCC Plus certification of these two sites will be followed by similar certifications at other manufacturing plants. A broad portfolio of technologies is being developed to address how component materials interact with the environment to improve recyclability, reduce raw material consumption, and minimize the impact of fugitive wastes.

Strict protective measures will make the industry meeting possible at the International Conference on Cellulose Fibres in Cologne on February 2 and 3, 2022. The latest innovations will be shocased: from hygiene and textiles to non-wovens and carbon fibre alternatives to lightweight construction applications. Online participation is also possible.

Cellulose fibres show an increasingly expanding wide range of applications, while at the same time markets are driven by technological developments and political framework conditions, especially bans and restrictions on plastics and increasing sustainability requirements. The conference provides rich information on opportunities for cellulose fibres through policy assessment, a session on sustainability, recycling and alternative feedstocks as well as latest development in pulp, cellulose fibres and yarns. This includes application such as non-wovens, packaging and composites.

Live at the conference, host nova-Institute and sponsor GIG Karasek GmbH will grand the “Cellulose Fibre Innovation of the Year” award to one of six highly interesting products, ranging from cellulose made of orange and wood pulp to a novel technology for cellulose fibre production. The presentations, election of the winner by the conference audience and the award ceremony will take place on the first day of the conference.

The conference sessions reflect the current topics of industry and research. “Strategies and Market Trends” provides an overview of the rapid development of cellulose fibres and their technological progress across the fibre market. An analysis of the key cost components of these fibres to benchmark against current cost levels will highlight future opportunities and challenges for novel textile fibres. The session will conclude with an overview of the industry's recent strategies to defossilize the fibre market.

The session “New Opportunities for Cellulose Fibres in Replacing Plastics”, focusses on questions such as: “What impact does the ban on plastics in single-use products have on the industry?” and “What are the latest regulatory issues and policy opportunities for cellulose fibres?”. This part of the conference presents new opportunities for the replacement of fossil-based insulating materials with cellulose-based technologies suitable for use in a variety of applications, from aerospace to mobility and construction.
Institutefor Ecology and Innovation

“Sustainability and Circular Economy” highlights crucial issues with regard to the overall goal of keeping the environmental impact of cellulose fibres low. A core theme of the session is the responsible use of wood and forests. With this objective, the five speakers discuss the importance of circular concepts for cellulose feedstocks. Exciting insights into the important “Hot Button Report” are offered by Canopy. The “Hot Button” report enables the producers of cellulose fibres to better understand the impact their raw materials have on forests and the climate development worldwide.

The full conference programme is available at www.cellulose-fibres.eu/program.

Under the ClusterXchange pilot scheme, the EXTRATEX partnership organised a 5-day exchange in Czech Republic, hosted by CLUTEX (cluster for technical textile).

15 participants visited strategic and innovative companies in the field of smart materials and advances technologies, as well as research centres and the Liberec University.

During the exchange, 92 B2B meetings were organized between local companies and the exchange participants, with 75% of the contacts established leading to follow-ups after the conclusion of the exchange. This collaboration laid the foundation for potential cross-border and cross-sector business collaboration, and participants of the physical exchange improved their competences in the field of smart materials and advanced technologies.

According to a testimony from the company Bipier Srl, their participation in the exchange allowed the establishment of two important working relationships with Bcb Informatica Y Control and Vyskummy Ustav Chemickych (Research Institute for Man-Made Fibers). This cooperation wil allow Bipier Srl to equip their machines with quality temperature control, and to expand the distribution of their products.

• More than 30 leading pioneers of the chemical and material sector welcome the latest political papers from Brussels, Berlin and Düsseldorf

The political situation for renewable carbon from biomass, CO2 and recycling for the defossilisation of the chemical and materials industry has begun to shift fundamentally in Europe. For the first time, important policy papers from Brussels and Germany take into consideration that the term decarbonisation alone is not sufficient, and that there are important industrial sectors with a permanent and even growing carbon demand. Finally, the need for a sustainable coverage of this carbon demand and the realisation of sustainable carbon cycles have been identified on the political stage. They are elemental to the realisation of a sustainable chemical and derived materials industry.

The goal is to create sustainable carbon cycles. This requires comprehensive carbon management of renewable sources, which includes carbon from biomass, carbon from Carbon Capture and Utilisation (CCU) – the industrial use of CO2 as an integral part – as well as mechanical and chemical recycling. And only the use of all alternative carbon streams enables a true decoupling of the chemical and materials sector from additional fossil carbon from the ground. Only in this way can the chemical industry stay the backbone of modern society and transform into a sustainable sector that enables the achievement of global climate goals. The Renewable Carbon Initiative’s (RCI) major aim is to support the smart transition from fossil to renewable carbon: utilising carbon from biomass, CO2 and recycling instead of additional fossil carbon from the ground. This is crucial because 72% of the human-made greenhouse gas emissions are directly linked to additional fossil carbon. The RCI supports all renewable carbon sources available, but the political support is fragmented and differs between carbon from biomass, recycling or carbon capture and utilisation (CCU). Especially CCU has so far not been a strategic objective in the Green Deal and Fit-for-55.

This will change fundamentally with the European Commission's communication paper on “Sustainable Carbon Cycles” published on 15 December. The position in the paper represents an essential step forward that shows embedded carbon has reached the political mainstream – supported by recent opinions from members of the European parliament and also, apparently, by the upcoming IPCC assessment report 6. Now, CCU becomes a recognised and credible solution for sustainable carbon cycles and a potentially sustainable option for the chemical and  material industries. Also, in the political discussions in Brussels, the term “defossilation” is appearing more and more often, complementing or replacing the term decarbonisation in those areas where carbon is indispensable. MEP Maria da Graça Carvahlo is among a number of politicians in Brussels who perceive CCU as an important future industry, putting it on the political map and creating momentum for CCU. This includes the integration of CCU into the new Carbon Removal Regime and the Emission Trading System (ETS).

As the new policy documents are fully in line with the strategy of the RCI, the more than 30 member companies of the initiative are highly supportive of this new development and are ready to support policy-maker with data and detailed suggestions for active support and the realisation of sustainable carbon cycles and a sound carbon management. The recent political papers of relevance are highlighted in the following.

Brussels: Communication paper on “Sustainable Carbon Cycles”
On 15 December, the European Commission has published the communication paper “Sustainable Carbon Cycles” . For the first time, the importance of carbon in different industrial sectors is clearly stated. One of the key statements in the paper is the full recognition of CCU for the first time as a solution for the circular economy, which includes CCU-based fuels as well. The communication paper distinguishes between bio-based CO2, fossil CO2 and CO2 from direct air capture when addressing carbon removal and it also announces detailed monitoring of the different CO2 streams. Not only CCU, but also carbon from the bioeconomy is registered as an important pillar for the future. Here, the term carbon farming has been newly introduced, which refers to improved land management practices that result in an increase of carbon sequestration in living biomass, dead organic matter or soils by enhancing carbon capture or reducing the release of carbon. Even though the list of nature-based carbon storage technologies is non-exhaustive in our view, we strongly support the paper’s idea to deem sustainable land and forest management as a basis for the bioeconomy more important than solely considering land use as a carbon sink. Surprisingly, chemical recycling, which is also an alternative carbon source that substitutes additional fossil carbon from the ground (i.e. carbon from crude oil, natural gas or from coal), is completely absent from the communication paper.

Berlin: Coalition paper of the new German Government: “Dare more progress – alliance for freedom, justice and sustainability”
The whole of Europe is waiting to see how the new German government of Social Democrats, Greens and Liberals will shape the German climate policy. The new reform agenda focuses in particular on solar and wind energy as well as especially hydrogen. Solar energy is to be expanded to 200 GW by 2030 and two percent of the country's land is to be designated for onshore wind energy. A hydrogen grid infrastructure is to be created for green hydrogen, which will form the backbone of the energy system of the future – and is also needed for e-fuels and sustainable chemical industry, a clear commitment to CCU. There is a further focus on the topic of circular economy and recycling. A higher recycling quota and a product-specific minimum quota for the use of recyclates and secondary raw materials should be established at European level. In the coalition paper, there is also a clear commitment to chemical recycling to be found. A significant change for the industry is planned to occur in regards to the so-called “plastic tax” of 80 cents per kilogram of non-recycled plastic packaging. This tax has been implemented by the EU, but most countries are not passing on this tax to the manufacturers and distributors, or only to a limited extent. The new German government now plans to fully transfer this tax over to the industry.

Düsseldorf: Carbon can protect the climate – Carbon Management Strategy North Rhine-Westphalia (NRW)
Lastly, the RCI highly welcomes North Rhine-Westphalia (NRW, Germany) as the first region worldwide to adopt a comprehensive carbon management strategy, a foundation for the transformation from using additional fossil carbon from the ground to the utilisation of renewable carbon from biomass, CO2 and recycling. For all three alternative carbon streams, separate detailed strategies are being developed to achieve the defossilisation of the industry. This is all the more remarkable as North Rhine-Westphalia is the federal state with the strongest industry in Germany, in particular the chemical industry. And it is here, of all places, that a first master plan for the conversion of industry from fossil carbon to biomass, CO2 and recycling is implemented. If successful, NRW could become a global leader in sustainable carbon
management and the region could become a blueprint for many industrial regions.

Freudenberg Performance Materials announces a general upward adjustment of their prices for nonwoven performance materials for flooring and filtration applications in EMEA. This revision, effective January 1, 2022, has become necessary because of sustained and unprecedented surge in cost for raw materials, packaging, freight, consumables and energy combined with disruptions in their inbound supply chain.

Prices across all categories have by far outpaced their expectations and are forecasted to remain on high levels throughout 2022. This historic price trend has placed significant pressure on Freudenberg Performance Materials, and they understand in a similar way on their customers.

At this stage their business can no longer absorb the effects of such high price levels. Freudenberg Performance Materials will therefore adjust our prices for all their Colback® and Lutradur branded nonwoven products for flooring and filtration application by double-digit increases depending on product types.

Freudenberg Performance Materials will continue to work on improving productivity to offset inflationary pressure to keep attractive price levels and to avoid further price adjustments. They will continue to monitor the market development and in case of sustained and unexpected downward trends they will adjust our prices accordingly.

INDA, the Association of the Nonwoven Fabrics Industry, and Nonwovens Industry Magazine have extended the due date for nominations for the IDEA® Achievement Awards. IDEA® is the preeminent event for the nonwovens and engineered fabrics conference and exposition and will be held at the Miami Beach Convention Center in Miami Beach, Florida USA, March 28-31, 2022.

The IDEA® Achievement Awards recognize leading companies and new innovations (since IDEA® in 2019) in the global engineered fabrics industry in six categories. Companies can nominate their products, or their customers’ products in as many categories as applicable, which are:

• Sustainability Advancement (advances one or more elements of sustainability or circularity since 2019)
• Equipment (best new equipment introduction since 2019)
• Raw Materials (best new raw materials introduction since 2019)
• Short-Life (best new disposable product introduction since 2019)
• Long-Life (best new durable product introduction since 2019)
• Nonwoven Product (best new nonwoven product introduction since 2019)

The submission deadline is now extended to February 1, 2022.  Selections will be made by members of the industry voting through Nonwovens Industry Magazine. Selection of the Entrepreneur Award will be made by Nonwovens Industry Magazine.

INDA, the Association of the Nonwoven Fabrics Industry, announced it has updated its value proposition to grow the nonwovens industry and establish its global leadership and versality in delivering essential, environmentally-responsible materials and products.

Resulting from an extensive strategic review process guided by industry experts, the new plan positions INDA to move forward from the business challenges of COVID that impacted its ability to hold in-person events.

INDA will equip the nonwovens industry and its customers to achieve business growth by focusing resources on shaping the external environment, and fostering actionable thought leadership on crucial issues. The association will continue to strengthen its vital role of bringing together industry experts in a pre-competitive environment by organizing and leading working groups and committees to focus on areas of mutual concern.

Dave Rousse, INDA President, stated, “We enthusiastically embrace the new foundation based on five key pillars that will guide INDA activities.” These pillars are:

• Convene and connect the industry through trade shows and conferences
• Achieve industry relevance among policy makers, end users, and other key stakeholders
• Advocate for the Nonwovens Industry in public policy forums
• Deliver market insights for better decision making
• Provide training programs to sustain the industry’s innovative edge

Rousse continued, “With last month’s announcement of Tony Fragnito joining INDA as Chief Operating Officer, we are ready to implement this plan and take it into the future. I look forward to working with him to drive INDA’s continuous pursuit of excellence in providing ever greater value to our industry and our members.”

INDA has retained several outside resources to survey members and develop this plan, as well as recruit the support needed to execute the plan over the next several years.

Microplastic pollution is a global challenge across many industries and sectors – one of critical importance being textiles.

A 2021 study by the California Ocean Science Trust and a group of interdisciplinary scientists acknowledges that microfibres from textiles are among the most common microplastic materials found in the marine environment. Every time synthetic clothes are manufactured, worn, washed, or disposed of, they release microplastics into terrestrial and marine environments, including human food chains. Synthetic fibres represent over two-thirds (69%) of all materials used in textiles, a proportion that is expected to rise to 73% by 2030. The production of synthetic fibres has fuelled a 40-year trend of increased per capita clothing consumption.

Global textile consumption has become:

• more reliant on non-renewable resources,
• less biodegradable, and
• increasingly prone to releasing microplastics.

The increased consumption is also discretionary, driven by consumer desire and remains unchecked. Thus, the long-term trend in the textile industry parallels the intentional addition of microplastics to products such as cosmetics. The contrast is that the European Chemicals Agency (ECHA) has recommended such intentional additions be restricted, whereas the over-consumption of synthetic fibres continues unchecked. One way for the EU to account for and mitigate microplastic pollution is through an EU-backed methodology measuring and reporting microplastic emissions, so that consumers and procurement officers have the information needed to minimise microplastic pollution resulting from their purchasing decisions.

There is a critical opportunity to address microplastic pollution in the fashion textile industry through the EU Product Environmental Footprint (PEF) methodology. To meet the environmental objectives of the Circular Economy Action Plan, the EU is proposing that companies substantiate their products’ environmental credentials using this harmonised methodology. However, microplastic pollution is not accounted for in the PEF methodology. This omission has the effect of assigning a zero score to microplastic pollution and would undermine the efforts of the European Green Deal, which aim “to address the unintentional release of microplastics in the environment.”

The incorporation of microplastic pollution as an indicator would increase the legitimacy of the PEF method as well as better inform consumer purchasing decisions, especially as the European Green Deal seeks to “further develop and harmonise methods for measuring unintentionally released microplastics, especially from tyres and textiles, and delivering harmonised data on microplastics concentrations in seawater.”

Whilst we continue to learn about the damage of microplastics and there is new knowledge emerging on the toxic impacts along the food chain, there is sufficient information on the rate of microplastic leakage into the environment to implement a basic, inventory level indicator in the PEF now. This is consistent with the recommendations of a review of microplastic pollution originating from the life cycle of apparel and home textiles. There are precedents in PEF for basic level (e.g., ‘resource use, fossils’) and largely untested (e.g. land occupation and toxicity indicators) indicators, and therefore an opportunity for the EU to promote research and development in the measurement and modelling of microplastic pollution by including such emissions in the PEF methodology. For such an indicator, the long and complex supply chains of the apparel and footwear industry would be a test case with high-impact and a global reach.

• JEC Group announces theme for JEC World 2022 and reaffirms global leadership in composites innovation, business and networking

JEC World, the leading global trade show dedicated to composite materials, their manufacturing technologies and application markets, will take place in Paris from March 8-10, 2022, under the theme Composites for a Sustainable World. JEC World 2022 will be the industry’s most awaited international face to face event after the long pandemic period. Exhibition space is already 98% booked, a clear demonstration of the industry’s commitment to meet and resume business. Those unable to join in person will be able to experience the show via the JEC World Connect digital platform.

“We are looking forward to welcoming our exhibitors, partners and visitors back to Paris to resume business and promote innovation,” comments Thomas Lepretre, VP Events, Sales and Operations of JEC Group. “JEC World will bring the composites industry together to showcase the sustainability benefits of composite materials to a global audience, and to provide a stimulating meeting-place for the industry to pursue its sustainability ambitions by exchanging knowledge, forging collaborations, and imagining new concepts to protect our environment.”

• JEC World a unique get-together on sustainability throughout the product lifecycle
• JEC World a real composites “think tank”
• JEC World 2022 will demonstrate how sustainable thinking is at the heart of the innovative designs, technologies and business models driving the development of the next generation of composites applications.

Four conferences will be held over the three days, focusing on:

• Sustainability of Raw Materials for Composites: Fueling the Circular Revolution
• Rethinking Composite Materials Production: The Path to Sustainable Manufacturing
• Design for Circular Composite Products: Turning Waste, Recycling & Reuse into Opportunities
• Applications of Composite Materials for Circularity: Towards a Net-Zero World

Innovation is in JEC World’s DNA
One of JEC World’s objective’s is to promote the composites sector’s most innovative projects. More than 600 product launches are expected to be announced over the three days of the show, which will also feature JEC’s high-regarded innovation challenges and awards ceremonies :

• The JEC Composites Innovation Awards celebrate innovative global composite projects, as well as fruitful collaborations between different players in the value chain. Over more than 15 years, the JEC Composites Innovation Awards have highlighted collaborations between some 1,900 companies and recognized 203 creative projects. The winners will be announced on March 7th during a dedicated ceremony and their successful technologies will be on display throughout the show.

• The JEC Composites Startup Booster is the leading startup competition in the world of composites. In 2022, this competition will celebrate its fifth anniversary, with a special event to be organized onsite and the launch of a new “sustainability” award. And, with 20 finalists for 2022, it will recognize innovations with the greatest potential market impact and promote them to an influential audience of decision-makers. The finalists’ innovations will be displayed at JEC World’s “Startup Village.”

• For the first time, JEC World will host the 3rd edition of the SMC BMC Design Award organized by the European Alliance for SMC BMC. This international competition recognizes and promotes design excellence in the use of SMC and BMC materials. The theme of this edition is Sustainable Living, and the award is opento design students and young design professionals (less than 3 years of experience) living in Europe.