From the Sector

Reset
757 results
Marchi & Fildi Group presents the selection of metalloplastic yarns with GRS certification of its Gleaming line, coming from 100% post-consumer recycled polyester (c) Marchi & Fildi Group
Linea Gleaming
24.11.2021

Italian spinning group launches new metalloplastic yarns

  • Marchi & Fildi Group presents the selection of metalloplastic yarns with GRS certification of its Gleaming line, coming from 100% post-consumer recycled polyester

With the goal to expand the offer of yarns coming from recycled raw materials for a textile more attentive to the consumption of resources, the MFT division of the Marchi & Fildi Group completes the range of metalloplastic yarns of its Gleaming collection with the insertion of 100% recycled polyester yarns coming from post-consumer material and with the GRS (Global Recycle Standard) certification.
Starting from recycled polyester with traceable origin, in compliance with environmental and social criteria extended to all the phases of the supply chain, metalloplastic yarns are obtained with the same esthetic features and performance, compared to similar products based on virgin raw materials.

  • Marchi & Fildi Group presents the selection of metalloplastic yarns with GRS certification of its Gleaming line, coming from 100% post-consumer recycled polyester

With the goal to expand the offer of yarns coming from recycled raw materials for a textile more attentive to the consumption of resources, the MFT division of the Marchi & Fildi Group completes the range of metalloplastic yarns of its Gleaming collection with the insertion of 100% recycled polyester yarns coming from post-consumer material and with the GRS (Global Recycle Standard) certification.
Starting from recycled polyester with traceable origin, in compliance with environmental and social criteria extended to all the phases of the supply chain, metalloplastic yarns are obtained with the same esthetic features and performance, compared to similar products based on virgin raw materials.

“Thanks to our commitment in the research of materials, we are able to propose metalloplastic yarns produced with 100% recycled material; the film used for the production of flat yarns, too, is in recycled polyester, with a quality level that is suitable for cutting – the Company explains -. Till now it was possible to find in the market only metalloplastic yarns with not recycled polyester flat yarn, twisted with certified fibers. This represents an important step forward to implement a circular economy possibility for this kind of products too”.

The Gleaming yarns GRS certified can be supplied in gold and silver, colors and transparent, in various counts, widths and types; they are suitable for use in flat and circular knitting, weaving, hosiery and as a component in fancy yarns.

The Gleaming line, with a wide selection of yarns in stock service, represents a completion of the offer of the Marchi & Fildi Group. The Gleaming yarns are offered in different thicknesses, widths and types with both metallized and transparent, iridescent, refracting and phosphorescent effects. The collection also includes items with special features of resistance to chemical and dyeing treatments. The Gleaming metalloplastic yarns find application in the world of fashion and furniture, for creative and fancy yarns and fabrics, accessories and decorations. Products with refractive features are also used in technical items like uniforms and workwear, sport garments and accessories, external ribbons and labels.

Source:

Marchi & Fildi Group

(c) AVK - Industrievereinigung Verstärkte Kunststoffe e. V.
24.11.2021

The AVK – Industrievereinigung Verstärkte Kunststoffe – presents its Innovation Awards 2021

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

Category “Research and Science”
First place in the “Research and Science” category was awarded to the German Aerospace Center (DLR) for its Bondline Control Technology (BCT). This innovative process is used for quality control and assurance of bonded joints. The core element is a porous fabric which is applied to a joining surface using an epoxy adhesive or matrix resin. Peeling away the fabric creates a chemically reactive and undercut surface and can also be used as a test to check adhesion to the substrate. BCT has potential in a variety of possible applications. For example, peel ply can be replaced by BCT fabric to produce composite components with an optimised joining surface. The cost-effective BCT peel test is suitable for coupon testing and process control. In addition, the combined adhesion test and surface pre-treatment can be used for quality assurance of bonded repairs on fibre composite structures.

Second place was taken by the Institute of Textile Technology (ITA) at RWTH Aachen University and its partners AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR with “StoneBlade – Lightweight construction with granite for the wind industry”. This innovation enables manufacturers to reduce the amount of non-recyclable materials used in rotor blade construction. At the same time, it reduces the weight of these components and improves the mechanical properties relating to the stability of wind turbines. The innovative approach replaces glass-fibre reinforced plastic in the blade components with hard rock – a natural, cost-effective and recyclable lightweight material. The slabs of rock are cut and ground to a thickness of just a few millimetres and embedded in a fibre composite laminate with carbon fibre, which stabilises them for alternating load cases. The pre-stressed material is pressure-stable in the composite and can absorb tensile forces in the event of continuously alternating loads without any loss of stiffness.

Third place went to the Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK) with its partner Mercedes Benz AG for the interdisciplinary development of a highly integrated inductive charging module for electric vehicles. The ultra-thin charging module was designed to make optimum use of space in the vehicle underbody without reducing ground clearance. An interdisciplinary approach was adopted for the development process. This involved the electrical, mechanical and process characterisation of high-frequency Litz wires, ferromagnetic foil and metal wire cloth as well as the creation of a simulation model. The result is a demonstrator for a charging system with a structural height of 15 mm and a total weight of 8 kg. It achieves a transmission efficiency of up to 92 percent at 7.2 kW nominal power and active air cooling. The hardware demonstrator was fabricated in a 3-step process using RTM and VARI techniques.

Overview of all the winners in the three categories:
Category “Innovative Products/Applications”
1st Place: “Traffic signs from Nabasco (N-BMC)” – Nabasco Products BV and Lorenz Kunststofftechnik GmbH, partners: Pol Heteren BV and NPSP BV
2nd Place: “Novel, ultratough vinyl ester resin for the construction of large marine vessels” Evonik Operations GmbH
3rd Place: “Air intake housing with a multi-material design for gas turbines” – MAN Energy Solutions SE, Leichtbau-Zentrum Sachsen GmbH and Leichtbau-Systemtechnologien KORROPOL GmbH.
Category “Innovative Processes”
1st Place: “In-mould wrapping” off-tool, film-coated, fibre composite components for exterior applications – BMW Group, Partner: Renolit SE
2nd Place: “Adaptive automated repair of composite structural components in the aviation sector” – Lufthansa Technik AG, Partner: iSAM AG
3rd Place: “Automated surface pre-treatment using VUV excimer lamps” – CTC GmbH
Category “Research and Science”
1st Place: “Bondline Control Technology (BCT)” – German Aerospace Center (DLR)
2nd Place: “StoneBlade – Lightweight construction with granite for the wind industry” – Institute of Textile Technology at RWTH Aachen University, Partners: AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR
3rd Place: “Interdisciplinary development of a highly integrated inductive charging module for electric vehicles” – Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK), Partner: Mercedes Benz AG

Submissions for the next Innovation Award can be made from the end of January 2022.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

24.11.2021

PERFORMANCE DAYS cancelled in Munich on December 1-2, 2021

  • Focus now on digital fair platform

The PERFORMANCE DAYS team regrets having to cancel at short notice the physical edition of PERFORMANCE DAYS which was scheduled to take place on December 1-2, 2021 at the Messe München exhibition center. Right up until today, the event organizers of PERFORMANCE DAYS were in the final stages of preparations for the fair. The goal of being able to realize a fully booked fair with a portfolio like in pre-pandemic times seemed to be within reach. The political regulations agreed in Bavaria from November 19, 2021 and the heavily restricted constraints associated with an incidence of 1000 have far-reaching consequences for PERFORMANCE DAYS. As a result of the current sharp rise in the number of infections in Munich, the planned winter edition must now be cancelled as a precaution. The focus now is now completely on the digital fair on December 1 and 2, 2021.

  • Focus now on digital fair platform

The PERFORMANCE DAYS team regrets having to cancel at short notice the physical edition of PERFORMANCE DAYS which was scheduled to take place on December 1-2, 2021 at the Messe München exhibition center. Right up until today, the event organizers of PERFORMANCE DAYS were in the final stages of preparations for the fair. The goal of being able to realize a fully booked fair with a portfolio like in pre-pandemic times seemed to be within reach. The political regulations agreed in Bavaria from November 19, 2021 and the heavily restricted constraints associated with an incidence of 1000 have far-reaching consequences for PERFORMANCE DAYS. As a result of the current sharp rise in the number of infections in Munich, the planned winter edition must now be cancelled as a precaution. The focus now is now completely on the digital fair on December 1 and 2, 2021.

The new measures are scheduled to come into effect in Munich from the middle of this week, which would lead to very short-term changes. The organizers of PERFORMANCE DAYS therefore see themselves in the responsibility to enable a minimum of planning security as well as a responsible handling of the given situation with this decision.

“Exceptional situations require exceptional decisions – making these all the more difficult. After experiencing a very successful and surprisingly well-attended fair with the Functional Fabric Fair by PERFORMANCE DAYS in Portland, Oregon last week, we have tried everything possible up to the last moment and firmly believed that we would finally set a further positive milestone with the physical edition of PERFORMANCE DAYS in Munich. We fulfilled all the requirements, updated our hygiene concept several times to comply with the dynamically changing measures and took all the necessary precautions for a safe event. Unfortunately, current developments do not allow us to host the trade fair event next week, since the undisputed top priority is the protection and health of our visitors. Now our focus turns to the full implementation of the Digital Fair on December 1 and 2, 2021”, explains Marco Weichert, CEO of PERFORMANCE DAYS

Focus on digital platform
The PERFORMANCE DAYS team is now investing all its efforts into implementing the Digital Fair on December 1 and 2, 2021. As part of THE LOOP, those interested have the opportunity as of now to view online the fabric innovations and news for the Winter Season 2023/24, this year’s Focus Topic “Sustainable Nylon” and the latest color trends. In the Marketplace, visitors will be able to view the numerous exhibitor products, including the PERFORMANCE FORUM’s curated sustainable fabric highlights. In order to present the fabrics to visitors as realistically as possible in terms of feel, design and structure in digital form, the PERFORMANCE FORUM has been equipped with new 3D-technology, including innovative tools such as 3D images, video animations and downloadable U3M files. Throughout the Digital Fair, exhibitors and fair visitors can look forward to extensive networking opportunities. For example, as part of the extensive digital supporting program on December 1, with various expert talks, discussion rounds and speakers via livestream, moderated by Charles Ross live from the studio. On December 2, the “sustain & innovate” conference on this year’s Focus Topic “The Sustainable Future of Nylon” will kick off with discussions and panels, moderated by Astrid Schlüchter, Editor-in-Chief of SAZsport and SPORTSFASHION by saz.  

A very special thank you goes out to the entire PERFORMANCE DAYS community with its exhibitors, visitors and partners for their active support, trust, loyalty and understanding in these still extraordinary times. The team looks forward to the Digital Fair on December 1 and 2, 2021 and further ahead to meeting you all personally on April 27 and 28, 2022 at the summer edition of PERFORMANCE DAYS live in Munich.

Source:

Performance Days

© Digital Capability Center
17.11.2021

Competence Centre WIRKsam - Shaping Work with AI

  •  14 million for the Rhenish coal region

Shaping economic change in the Rhenish textile and coal region together with artificial intelligence (AI) - this is the goal of the WIRKsam competence centre launched at the beginning of November. The joint project, funded by the Federal Ministry of Education and Research, is researching innovative forms of work to secure employment, create attractive jobs and strengthen regional companies.
 

With a focus on the strengths of the Rhenish mining area, WIRKsam is to establish itself as a central point of contact and align various scientific institutions and their research specifically to the challenges of the regional working world. Funded by the BMBF with 14 million euros over five years, the project is fundamentally about transferring scientific findings into company practice and into the wider society. After the funding phase, the centre of excellence will continue to work independently.

  •  14 million for the Rhenish coal region

Shaping economic change in the Rhenish textile and coal region together with artificial intelligence (AI) - this is the goal of the WIRKsam competence centre launched at the beginning of November. The joint project, funded by the Federal Ministry of Education and Research, is researching innovative forms of work to secure employment, create attractive jobs and strengthen regional companies.
 

With a focus on the strengths of the Rhenish mining area, WIRKsam is to establish itself as a central point of contact and align various scientific institutions and their research specifically to the challenges of the regional working world. Funded by the BMBF with 14 million euros over five years, the project is fundamentally about transferring scientific findings into company practice and into the wider society. After the funding phase, the centre of excellence will continue to work independently.

Prospects: Attractive jobs in the lignite mining region
The region on the left bank of the Rhine is not only a lignite mining area, but also a historically grown textile region where technical textiles are produced today, for example for medical technology or plant and vehicle construction. This offers valuable future prospects for the employees affected by the lignite phase-out.

Against this background, the aim of the WIRKsam centre of excellence is to research the extensive possibilities of artificial intelligence for shaping the future world of work and to transfer them to companies. AI applications are used to develop innovative work and process flows to create attractive workplaces and increase the competitiveness of local companies.

Together: business and science
The special feature: research institutions and companies from the Rhenish textile industry and related sectors work together in the centre of excellence. Research partners are the Institut für Textiltechnik (ITA) of RWTH Aachen University and the Institute for Mobile Autonomous Systems and Cognitive Robotics (MASCOR) of FH Aachen University of Applied Sciences, headed by ifaa - Institut für angewandte Arbeitswissenschaft e.V. (Institute for Applied Work Science).

Nine regional companies are involved so far; more will join. AI applications are being developed and exemplarily implemented for their respective needs. In this way, the diverse potentials of AI for work design are being tested and qualification requirements derived. These results will not only increase the global competitiveness of the textile industry and other sectors; they will also secure jobs and make an important contribution to overcoming structural change in the Rhenish lignite mining area.

WIRKsam is funded by the Federal Ministry of Education and Research as part of the funding measure "Regional Competence Centres for Labour Research" and is supervised by the Karlsruhe Project Management Agency (PTKA) (funding code: 02L19C600). The WIRKsam competence centre will be based in Hürth, Germany, on the edge of the Rhenish mining area as soon as the conversion work on the former TV studios on the Euronova campus is completed.

More information:
AI
Source:

ITA – Institut für Textiltechnik of RWTH Aachen University

17.11.2021

NCTO welcomes Biden Administration’s Buy American Waiver Process

National Council of Textile Organizations (NCTO) President and CEO Kim Glas issued a statement welcoming the Biden administration’s launch of new database and waiver process for government contract solicitations made under the Buy American Act.

You can read the statement here.

National Council of Textile Organizations (NCTO) President and CEO Kim Glas issued a statement welcoming the Biden administration’s launch of new database and waiver process for government contract solicitations made under the Buy American Act.

You can read the statement here.

Source:

NCTO

(c) Kai-Chieh Kuo
17.11.2021

ITA PhD student Kai-Chieh Kuo was awarded Best Master’s Thesis Award of Walter Reiners-Stiftung

Kai-Chieh Kuo, PhD student at the Institut für Textiltechnik (ITA) of RWTH Aachen University, was awarded the German Textile Mechanical Engineering 2021 Best Master's Thesis Award for his master's thesis entitled "Modification of the tube weaving process of fine yarns for the production of woven ultra-low profile stent grafts". The prize is endowed with 3,500€. Peter D. Dornier, Chairman of the Board of the Walter Reiners-Stiftung (Foundation), virtually presented the award on the occasion of the ADD International Textile Conference on 9 November 2021.

Kai-Chieh Kuo, PhD student at the Institut für Textiltechnik (ITA) of RWTH Aachen University, was awarded the German Textile Mechanical Engineering 2021 Best Master's Thesis Award for his master's thesis entitled "Modification of the tube weaving process of fine yarns for the production of woven ultra-low profile stent grafts". The prize is endowed with 3,500€. Peter D. Dornier, Chairman of the Board of the Walter Reiners-Stiftung (Foundation), virtually presented the award on the occasion of the ADD International Textile Conference on 9 November 2021.

Minimally invasive endovascular aortic repair (EVAR) with textile stent-graft systems is nowadays a clinically established therapy procedure for the treatment of abdominal aortic aneurysms (AAA) – pathological bulges of the aorta. Due to the thick profile of the folded stent graft systems, there is currently a high risk of injuring narrowed or highly angulated access vessels from the inside during implantation. Stent graft systems with smaller profiles could provide an improvement, which could overcome complicated access routes through a lower bending stiffness. One possible approach for reducing the system profiles is the use of thin-walled tubular woven fabrics made of ultrafine multifilament yarns (≤20 dtex) as graft material.

Up to now, it has not been possible to process the fine yarns with the required high thread density (>200 threads/cm) and the available weaving technology in order to guarantee sufficient tightness against blood.

In his master's thesis, Kai-Chieh Kuo made high-density tubular weaving of ultra-fine filament yarns possible for the first time by means of suitable modifications to a shuttle loom as well as adaptations in the weaving preparation. In particular, he developed a new innovative reed technology that reduces warp thread friction during the shedding process and thus improves the process stability of the dense tube weaving process of fine yarns.

With the help of the process modification, it was then possible to produce high-density, thin-walled tubular woven fabrics, which were positively evaluated with regard to their suitability for a stent graft. Above all the potential of these tubular fabrics lies in their extremely thin-walled fabric profile, which seals well against blood. By using these new types of tubular fabrics as graft material for stent grafts, the system profile of the folded stent graft system can be reduced without having to compromise the blood tightness of the implant. The technology developed by Mr Kuo is not only applicable to stent graft systems, but also offers great possibilities for use in all other endovascular implants such as trans catheter heart valves, covered stents and small-lumen vascular prostheses.

17.11.2021

C.L.A.S.S. welcomes Sensil® BioCare by NILIT into its material hub

C.L.A.S.S. MATERIAL HUB is a careful selection of smart ingredients made by cutting-edge companies and innovators across the globe. The wide range includes transparent and traceable products, which can be natural/organic, up or re-cycled/able, or innovative and always representing a new generation of innovation that is minimizing its impact on people, environment, animals and oceans.

C.L.A.S.S. MATERIAL HUB is a careful selection of smart ingredients made by cutting-edge companies and innovators across the globe. The wide range includes transparent and traceable products, which can be natural/organic, up or re-cycled/able, or innovative and always representing a new generation of innovation that is minimizing its impact on people, environment, animals and oceans.

Sensil® BioCare sustainable premium Nylon fiber is enhanced with a technology, that helps lessen the persistence of textile waste in sea water and in landfills. With its embedded technology, if any microfibers of Sensil® BioCare garments are released during washing, they will be broken down at a quicker rate compared to conventional Nylon 6.6 fibers when they end up in the oceans. Tests were conducted in both landfill soil and sea water simulations to understand the potential impact of Sensil® BioCare on both ecosystems. Specifically, initial testing following the ASTM D6691 Standard Test Method For Determining Aerobic Biodegradation Of Plastic Materials In The Marine Environment and the ASTM D5511 Standard Test Method For Determining Anaerobic Biodegradation Of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions indicates that Sensil® BioCare yarns break down more rapidly (with a biodegradation of about 40% in 500 days) than conventional nylon. These promising findings point to reduced waste accumulation in both oceans and landfills.

NILIT, owner of the sustainable brand SENSIL®, has also teamed up with The Ocean Foundation’s Blue Resilience Initiative to reestablish and safeguard essential ocean meadows and other coastal habitats. These marine grasslands, which are being damaged at a rate of two football fields every hour, are vital ecosystems for sequestering CO2 from the atmosphere, thus reducing global warming and ocean acidification. In addition, ocean grasslands sustain sea life, defend coast lines against erosion and storm surge, and support economies around the world.

NILIT’s plant in Israel, who produce Sensil ® Biocare boosts, renowned certifications such as GRS (Global Recycled Standard)*, ISO 9001**, ISO 14001*** and ISO 45001****. Moreover, the company has already announced that all other plants in  the USA, China and Brazil will be ISO 14001 certified within 2021 and ISO 45001 certified within 2025. Worth to mention, 40% of Nilit’s team is made up of women.

Source:

C.L.A.S.S.

(c) JEC Group
16.11.2021

JEC Forum DACH: Latest news about the event

JEC Forum DACH will open its doors from November 23 – 24, 2021, the promise of a two-days gathering around business meetings and conferences. JEC Forum DACH will offer actors of the composites profession in the region the opportunity to exchange and learn about current and future developments of the industry through a rich program of conferences, the JEC Composites Startup Booster, and the AVK Innovation Awards. It also includes pre-arranged Business Meetings between sponsors and attendees as well as sponsors’ workshops.

CONFERENCES, KEYNOTES, AND MARKET OVERVIEW
JEC Forum DACH will feature cutting-edge live conferences with experts from the industry as well as
exclusive keynotes organized by the AVK.

MEETINGS PROGRAM
In  order  to  help  the  sponsors  to  save  time  and  establish  connections  with  real-interest business partners, JEC Group has developed a Business Meetings program: an efficient facilitator to connect precise needs to corresponding offers. These one-to-one meetings will be held on the sponsors’ booths during the two days of the event.

JEC Forum DACH will open its doors from November 23 – 24, 2021, the promise of a two-days gathering around business meetings and conferences. JEC Forum DACH will offer actors of the composites profession in the region the opportunity to exchange and learn about current and future developments of the industry through a rich program of conferences, the JEC Composites Startup Booster, and the AVK Innovation Awards. It also includes pre-arranged Business Meetings between sponsors and attendees as well as sponsors’ workshops.

CONFERENCES, KEYNOTES, AND MARKET OVERVIEW
JEC Forum DACH will feature cutting-edge live conferences with experts from the industry as well as
exclusive keynotes organized by the AVK.

MEETINGS PROGRAM
In  order  to  help  the  sponsors  to  save  time  and  establish  connections  with  real-interest business partners, JEC Group has developed a Business Meetings program: an efficient facilitator to connect precise needs to corresponding offers. These one-to-one meetings will be held on the sponsors’ booths during the two days of the event.

FEATURED SPONSORS’ WORKSHOPS
JEC Forum DACH will host 9 sponsors’ workshops during the two days: CMS SPA, Elantas Europe S.r.l., Kisling AG, Kroenert GmbH & Co KG, Maschinenfabrik Herbert MEYER GmbH, Netzsch Process Intelligence GmbH and Schwarzpunkt (part of Helvoet Group), Saertex GmbH & Co KG and SVT, Trima Spol Sro and Walter Mäder AG will present their know-how and technology during 30 minutes’ presentations in front of the attendees as well as in livestreaming.

FOSTERING ENTREPRENEURSHIP WITH THE JEC COMPOSITES STARTUP BOOSTER
JEC Composites Startup Booster is the leading startup competition in the world of composites.
It enables the community to find and assess innovations with a potential impact on their respective industries. The competition will be held at JEC Forum DACH for the first time with the pitches’ session on November 23rd at 2:15pm followed by the Awards ceremony at 6:15 pm.
The finalists are: ANYBRID (Germany), CARBON CLEANUP (Austria), CARBON-DRIVE (Germany), FIBRECOAT (Germany), and TOUCH SENSITY (France).

CELEBRATING INNOVATION WITH THE AVK INNOVATION AWARDS
This year at JEC Forum DACH, JEC Group and AVK will co-organize the AVK Innovation Award.
One of the goals of the AVK Innovation Awards is to give prominence to the innovations and the companies/institutions behind them, thus publicizing their performance throughout the industry. These awards will celebrate innovations in fiber-reinforced plastics (FRP) / composites during the Awards ceremony on Tuesday 23rd, at 6:15pm.

Full program and speakers list here.

Source:

JEC Group

Mahlo: Two heads of subsidiaries celebrate anniversaries (c) Mahlo
Michel Bruni, CEO of Mahlo Italia
16.11.2021

Mahlo: Two heads of subsidiaries celebrate anniversaries

At the subsidiaries of the German Mahlo GmbH + Co KG, two branch managers are celebrating anniversaries this year. Alan Lavore, CEO of Mahlo America Inc., has been with the machine builder for 25 years. Michel Bruni, CEO of Mahlo Italia, has been part of the Mahlo family for 40 years.

Bruni began his career at Mahlo in 1981 as a service technician in the French branch Mahlo Ouest. Just one year later, he moved to Mahlo Italia, where he was appointed branch manager in 1996. He still holds this position today. Bruni is also sales manager for the Benelux countries, the Maghreb countries and Madagascar. The Mahlo Italia CEO's recipe for success includes expertise paired with experience and passion. To remain loyal to a company for so many years also testifies to a special relationship. "Then as now, I work with a dynamic and committed team. We also have a very good relationship with the employees of the parent company in Germany," says Bruni.

At the subsidiaries of the German Mahlo GmbH + Co KG, two branch managers are celebrating anniversaries this year. Alan Lavore, CEO of Mahlo America Inc., has been with the machine builder for 25 years. Michel Bruni, CEO of Mahlo Italia, has been part of the Mahlo family for 40 years.

Bruni began his career at Mahlo in 1981 as a service technician in the French branch Mahlo Ouest. Just one year later, he moved to Mahlo Italia, where he was appointed branch manager in 1996. He still holds this position today. Bruni is also sales manager for the Benelux countries, the Maghreb countries and Madagascar. The Mahlo Italia CEO's recipe for success includes expertise paired with experience and passion. To remain loyal to a company for so many years also testifies to a special relationship. "Then as now, I work with a dynamic and committed team. We also have a very good relationship with the employees of the parent company in Germany," says Bruni.

The culture and integrity with which business is conducted in the family-owned company were among the reasons why Mahlo America Inc. CEO Alan Lavore has also been with Mahlo for 25 years. "I just love working with all the great people at Mahlo." Lavore joined Mahlo in 1996 as a territory sales manager and took over as CEO in 2005. During this time, he drove the company's expansion from a textile specialist to a supplier for various production sectors such as film, paper, coating and converting or nonwovens.

More information:
Mahlo nonwovens Automation
Source:

Mahlo GmbH + Co. KG

(c) Abu Dhabi Government Media Office
15.11.2021

Partnership between ADNOC and Borealis to expand Borouge Facility

  • ADNOC and Borealis confirm final investment agreement to build Borouge 4 in Ruwais, United Arab Emirates (UAE), which will produce 1.4 million tons of polyethylene per annum
  • Expansion project includes construction of a 1.5 million tonnes ethane cracker, two state-of-the-art Borstar® polyethylene plants and a cross-linked polyethylene plant
  • Borouge 4 will meet growing customer demand across the Middle East, Africa and Asia with differentiated polyolefin solutions in energy, infrastructure, and advanced packaging
  • New facility will benefit from industry-leading technologies to significantly improve energy efficiency and lower emissions, with carbon capture study underway
  • Upon expansion, Borouge will be the world's largest single-site polyolefin complex and will supply feedstock to TA'ZIZ Industrial Chemicals Zone Body

ADNOC and Borealis AG signed an USD 6.2 billion investment agreement to build the fourth Borouge facility – Borouge 4 – at the polyolefin manufacturing complex in Ruwais, United Arab Emirates (UAE).

  • ADNOC and Borealis confirm final investment agreement to build Borouge 4 in Ruwais, United Arab Emirates (UAE), which will produce 1.4 million tons of polyethylene per annum
  • Expansion project includes construction of a 1.5 million tonnes ethane cracker, two state-of-the-art Borstar® polyethylene plants and a cross-linked polyethylene plant
  • Borouge 4 will meet growing customer demand across the Middle East, Africa and Asia with differentiated polyolefin solutions in energy, infrastructure, and advanced packaging
  • New facility will benefit from industry-leading technologies to significantly improve energy efficiency and lower emissions, with carbon capture study underway
  • Upon expansion, Borouge will be the world's largest single-site polyolefin complex and will supply feedstock to TA'ZIZ Industrial Chemicals Zone Body

ADNOC and Borealis AG signed an USD 6.2 billion investment agreement to build the fourth Borouge facility – Borouge 4 – at the polyolefin manufacturing complex in Ruwais, United Arab Emirates (UAE).

The world-scale expansion confirms both partners’ commitment to the growth of Borouge and to support chemical production, and advanced manufacturing and industry in Ruwais, a key pillar of Abu Dhabi and the UAE’s technology, innovation and industrial development strategy. Borouge produces crucial industrial raw materials, which are exported to customers globally and used by local companies, boosting local industrial supply chains and enhancing In-Country Value.

Borouge 4 will capitalize on the projected growth in customer demand for polyolefins, driven by their use in manufactured products in the Middle East, Africa and Asia. The facility will also enable the next phase of growth at the Ruwais Industrial Complex by supplying feedstock to the TA’ZIZ Industrial Chemicals Zone.

Borouge 4 will have an industry-leading focus on sustainability leveraging the capabilities of both shareholders. The facility will utilize Borealis’ proprietary Borstar technology, to produce a product portfolio focused on durable applications for energy, infrastructure, advanced packaging, and agriculture sectors. This unique technology, in combination with hexene co-monomer, will enable the production of advanced packaging grades with up to 50% recycled polyethylene content.

Subject to an in-depth study, a Carbon Capture unit that would reduce CO2 emissions by 80% could also be operational in time for Borouge 4’s start-up. The facility is also designed to capitalize on ADNOC’s recent initiatives on clean energy, decarbonizing its power supply through access to Abu Dhabi’s clean power sources. These initiatives are aligned with the UAE Net Zero by 2050 Strategic Initiative.

The first Borouge facility, producing 450,000 tons of polyethylene per annum was commissioned in 2001. Borouge 2 and Borouge 3 took capacity to 2 million tons and 4.5 million tons of polyethylene and polypropylene per annum in 2010 and 2014 respectively.  Borouge 4 will boost the company’s annual polyolefin production to 6.4 million tons, making Borouge one of the world’s largest single-site polyolefin facilities.

The new Borouge 4 facility will comprise:

  • An ethane cracker, with 1.5 million tons ethylene output per annum, which will be the fourth cracker in Borouge’s integrated petrochemical complex in Ruwais
  • Two additional Borstar® polyethylene (PE) plants, each with 700 thousand tons per annum capacity, using state-of-the-art Borealis Borstar third generation (3G) technology
  • A cross-linked PE (XLPE) plant of 100 thousand tons per annum capacity.
  • A hexene-1 unit, which will produce co-monomers for certain grades of polyethylene.
Source:

Borealis

11.11.2021

Berto travels zero km to support B2C brands

In 2021, Berto Industria Tessile embarked on a series of journeys through the denim supply chain, touching both B2B and B2C worlds.

The first journey of this adventure, aimed at discovering and publicizing the world of indigo and, began by talking about the collaboration with the turkish garment maker blue matters creating a green collection to be proposed to the world's top brands, continuing with “su mirura project” in the second chapter.
This project has its objective in supports, with a ready on stock fabrics, (which at this time of difficult availability of product becomes extremely relevant), young emerging talents in the world of fashion that, in our industry, both for problems related to  minimum order quantities and for problems related to financial commitments of startups, would having difficulty in the raw materials research.

In this third chapter of the personal voyage into the world of denim, Berto Industria Tessile talks about two realities that are not only made in Italy, but also made in veneto, for a zero km circularity supports.

In 2021, Berto Industria Tessile embarked on a series of journeys through the denim supply chain, touching both B2B and B2C worlds.

The first journey of this adventure, aimed at discovering and publicizing the world of indigo and, began by talking about the collaboration with the turkish garment maker blue matters creating a green collection to be proposed to the world's top brands, continuing with “su mirura project” in the second chapter.
This project has its objective in supports, with a ready on stock fabrics, (which at this time of difficult availability of product becomes extremely relevant), young emerging talents in the world of fashion that, in our industry, both for problems related to  minimum order quantities and for problems related to financial commitments of startups, would having difficulty in the raw materials research.

In this third chapter of the personal voyage into the world of denim, Berto Industria Tessile talks about two realities that are not only made in Italy, but also made in veneto, for a zero km circularity supports.

Two brands that are part of two different segments of the indigo world of b2c, one operating in the world of clothing and one in the creation of fashion accessories, but who have a common denominator between them, the use of 100% in their collections of denim fabric Berto.*

* See attached document for more information.

Source:

Berto Industria Tessile / EFFE-BI

© ITM / TU Dresden
10.11.2021

Kreativitätspreis des Deutschen Textilmaschinenbaues 2021 geht an Irina Kuznik

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Frau Dipl.-Ing. Irina Kuznik vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden wurde mit dem 3.000 EUR dotierten Kreativitätspreis des Deutschen Textilmaschinenbaues 2021 für ihre exzellente Diplomarbeit „Entwicklung zur umweltfreundlichen Herstellung neuartiger Chitosanfasergarne unter Einsatz von ionischen Flüssigkeiten" ausgezeichnet.

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Frau Dipl.-Ing. Irina Kuznik vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden wurde mit dem 3.000 EUR dotierten Kreativitätspreis des Deutschen Textilmaschinenbaues 2021 für ihre exzellente Diplomarbeit „Entwicklung zur umweltfreundlichen Herstellung neuartiger Chitosanfasergarne unter Einsatz von ionischen Flüssigkeiten" ausgezeichnet.

In ihrer Diplomarbeit entwickelte Frau Kuznik einen völlig neuen Ansatz zur ökologischen und ökonomischen Herstellung von Chitosangarnen. Unter Nutzung ionischer Flüssigkeiten als gut geeignetes, neuartiges Lösungsmittel für Chitosan lässt sich Chitosan mit geringen Deacetylierungsgraden sowie reines Chitin erfolgreich auflösen. In einem Nassspinnverfahren können damit erzeugte Spinnlösungen zu neuartigen Chitosan- bzw. Chitinmonofilamenten mit sehr guten morphologischen Eigenschaften hergestellt werden. Des Weiteren lässt sich die ionische Flüssigkeit mittels eines Verdampfungsverfahrens aus dem Abwasser zurückgewinnen und wiederaufbereitet werden.

More information:
VDMA Textilmaschinen chitosan
Source:

Technische Universität Dresden
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

(c) ITM/TU Dresden
10.11.2021

Förderpreis beste Dissertation des Deutschen Textilmaschinenbaues 2021 an Dr.-Ing. Martin Hengstermann

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Dr.-Ing. Martin Hengstermann wurde mit dem mit 5.000 EUR dotierten Förderpreis beste Dissertation des Deutschen Textilmaschinenbaues 2021 für seine am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden erarbeiteten Dissertation „Entwicklung von Hybridgarnen aus recycelten Carbonfasern und Polyamid 6-Fasern für thermoplastische Verbundbauteile mit hohem Leistungsvermögen“ geehrt.

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Dr.-Ing. Martin Hengstermann wurde mit dem mit 5.000 EUR dotierten Förderpreis beste Dissertation des Deutschen Textilmaschinenbaues 2021 für seine am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden erarbeiteten Dissertation „Entwicklung von Hybridgarnen aus recycelten Carbonfasern und Polyamid 6-Fasern für thermoplastische Verbundbauteile mit hohem Leistungsvermögen“ geehrt.

Gegenstand der Dissertation ist die Entwicklung und Umsetzung von neuartigen Hybridgarnen aus recycelten Carbonfasern (rCF) und Polyamid (PA) 6-Fasern für thermoplastische Verbundbauteile. Diese Hybridgarne können die hervorragenden mechanischen Eigenschaften der rCF im Gegensatz zu bisherigen Lösungen in hohem Maße ausnutzen. Bedingt durch deren spezielle Fasereigenschaften (insbesondere hohe Querkraftempfindlichkeit, Sprödigkeit und fehlende Kräuselung) wurde dafür die Prozesskette der konventionellen Stapelfasergarnherstellung, bestehend aus Krempel, Strecke und Flyer, umfangreich analysiert und technologisch-konstruktiv weiterentwickelt, wodurch erstmalig eine schonende und gleichmäßige Herstellung der Hybridgarne ermöglicht werden konnte.

Source:

Technische Universität Dresden
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

10.11.2021

AFRY to digitalize Renewcell’s textile recycling processes

The Swedish textile recycling company, Renewcell, has chosen AFRY as partner in order to digitalize production operations in their plants in Kristinehamn and Sundsvall, Sweden. AFRY will deliver an Industrial IT solution, containing AFRY MES and AFRY ProTAK, to manage production information and secure both high quality, as well as high overall efficiency in the production. The delivered solution will serve as a hub for all production process information.

The Swedish textile recycling company, Renewcell, has chosen AFRY as partner in order to digitalize production operations in their plants in Kristinehamn and Sundsvall, Sweden. AFRY will deliver an Industrial IT solution, containing AFRY MES and AFRY ProTAK, to manage production information and secure both high quality, as well as high overall efficiency in the production. The delivered solution will serve as a hub for all production process information.

Renewcell is a multi-award-winning textile recycling company based in Sweden. With the technology they have developed, the company has succeeded in recycling and regenerating textile fiber from old clothes to turn it back into fiber pulp. Renewcell has had a production site in Kristinehamn since 2017 and is now scaling up the production in their new production plant in Sundsvall. The new plant is expected to be operating during the first half of 2022. “Modern production and logistics require a high level of digitalization to meet the demands for, e.g., traceability, and therefore the systems and experience from AFRY will be very important to us,” says Ylva Stjernquist, Supply Chain Manager and Project Leader at Renewcell.

AFRY has a long experience in Industrial IT and will now deliver the two leading, closely integrated digital solutions for production management to Renewcell. The AFRY MES (Manufacturing Execution System) is a highly advanced digital information system that connects, monitors, and controls the complex production systems and data flows of the production processes. AFRY ProTAK is a digital tool that measures the effectiveness of a plant’s production machine performance. The system gathers information from different sources (e.g., DCS, MES, Maintenance) and combines that with the operators’ notes to calculate or present Overall Equipment Efficiency (OEE), which will lead to optimized production and increased profitability.

Together these tools will improve traceability and secure a high production efficiency by integrating data from all production systems and equipment. “We are focusing on improving sustainability within process industries, and it is therefore an honor to be part of Renewcell’s textile recycling through a full-scale digitalized solution. Our modern and competitive digital solution will definitely bring added value to these types of processes,” says David Andersson, Business Segment Manager Digitalization, AFRY Process Industries Sweden.  

AFRY MES and AFRY ProTAK will be installed to both Kristinehamn and Sundsvall plants. The installation is planned to be up and running during Q2 2022.

Source:

Process Industries Sweden

10.11.2021

Stahl achieves certification for its lifecycle assessment systems in partnership with Spin 360

Stahl, an active proponent of responsible chemistry, has taken an important step toward realizing its target of having lifecycle assessment (LCA) data for all strategic products by the end of 2023. By working closely together with Spin 360, a tech-enabled sustainability consultancy, Stahl has achieved certification of LCA data generation systems, allowing verifiable information to be collected for its products.
LCA is a methodology that measures the impact of any product on the environment over the course of its life. The LCA methodology can provide quantitative data in a format that permits comparisons to be made. The certification of LCA data generation systems is a foundational step to ensuring the accuracy and reliability of future LCA analyses.

Stahl, an active proponent of responsible chemistry, has taken an important step toward realizing its target of having lifecycle assessment (LCA) data for all strategic products by the end of 2023. By working closely together with Spin 360, a tech-enabled sustainability consultancy, Stahl has achieved certification of LCA data generation systems, allowing verifiable information to be collected for its products.
LCA is a methodology that measures the impact of any product on the environment over the course of its life. The LCA methodology can provide quantitative data in a format that permits comparisons to be made. The certification of LCA data generation systems is a foundational step to ensuring the accuracy and reliability of future LCA analyses.

Through close collaboration, Stahl and Spin 360 have implemented an Environmental Product Declaration (EPD) system – certified by Bureau Veritas – at Stahl’s site in Palazzolo, Italy. An EPD is an independently verified and registered document that communicates transparent and comparable information about the environment impact of products across their entire lifecycle. This implementation underlines Stahl’s commitment to enabling the sustainable development of its industry by driving accountability and transparency.

Michael Costello, Stahl Group ESG Director: “One of Stahl’s strategic ESG goals is to collect verifiable, high-quality LCA data for its products, thereby paving the way to lowering the environmental impact of the whole supply chain. This EPD system certification is an important achievement, and a key step in realizing this goal. Looking ahead, we’ll continue to work with our partners to enable our certified LCA data availability and shape a better industry.”

Federico Brugnoli, CEO of Spin 360: “We are very proud to have supported this complex process that will ensure the complete reliability of Stahl’s LCA data. Now we will look at the next steps in supporting Stahl, focusing environmental footprint reductions through science-based evolution of the industry. We’re confident that – together – we can ensure a better future for us all.”

VDMA: Top young talent with cutting-edge topics  (c) VDMA
The 2021 winners (from top left to right): Dr Martin Hengstermann, Irina Kuznik, Kai-Chieh Kuo.
10.11.2021

VDMA: Top young talent with cutting-edge topics

The Chairman of the Walter Reiners-Stiftung foundation of the VDMA Textile Machinery Association, Peter D. Dornier has awarded prizes to three successful young engineers. The award-winning works provide practical solutions on the topic of circular economy. For example, the recycling of carbon fibres, which are used to produce lightweight components for the automotive industry. Or the environmentally friendly production of yarns from crab shells. Another topic was medical applications: The processing of ultra-fine yarns into stents for aortic repair. The award ceremony took place online on 9 November as part of the Aachen-Dresden-Denkendorf International Textile Conference.  

With a creativity prize, endowed with 3,000 euros, the foundation honoured the diploma thesis of Irina Kuznik, TU Dresden. She used a creative approach to realise solutions for processing chitosan into fibre yarn.

The Chairman of the Walter Reiners-Stiftung foundation of the VDMA Textile Machinery Association, Peter D. Dornier has awarded prizes to three successful young engineers. The award-winning works provide practical solutions on the topic of circular economy. For example, the recycling of carbon fibres, which are used to produce lightweight components for the automotive industry. Or the environmentally friendly production of yarns from crab shells. Another topic was medical applications: The processing of ultra-fine yarns into stents for aortic repair. The award ceremony took place online on 9 November as part of the Aachen-Dresden-Denkendorf International Textile Conference.  

With a creativity prize, endowed with 3,000 euros, the foundation honoured the diploma thesis of Irina Kuznik, TU Dresden. She used a creative approach to realise solutions for processing chitosan into fibre yarn.

Mr Kai-Chieh Kuo was awarded the diploma/master's thesis promotion prize of 3,500 euros. With his master's thesis, which was written at RWTH Aachen University, Mr Kuo contributes to the production of vital components used in medicine. The stents made of ultra-fine yarns are made possible by an innovative modification of the classic tube weaving process.

The Walter Reiners Foundation rewarded the doctoral thesis of Dr. Martin Hengstermann with the promotional prize in the dissertation category, endowed with 5,000 euros. The thesis deals with the production of recycled carbon fibres. These can be used to produce lightweight components for motor vehicle and aircraft construction or the wind energy sector.

New Prize Sustainability / Circular Economy
The environmental conditions of the textile industry and machine construction are changing. Topics such as climate protection and the circular economy are becoming central. From this perspective, the board of the Walter Reiners Foundation has decided to further develop the foundation's prize system.

In 2022, the foundation will for the first time offer a prize with a focus on design / sustainability. Peter D. Dornier, Chairman of the Foundation, explained: "Already in the design phase, one can set the parameters so that a textile product can be reintroduced after use into the economic cycle for a high-quality application. For example, through the appropriate use of materials and finishing. We are looking for solutions for resource-saving design, technology and manufacturing processes."   

09.11.2021

Alchemie Technology asks fashion industry to reduce emissions

Alchemie Technology, an innovator of low energy, waterless, textile dyeing and finishing technology, is calling on COP26 leaders to support the global fashion industry in the adoption of new manufacturing technology, which will dramatically reduce carbon emissions and fashion’s impact on climate change.

While the fashion industry is one of the most polluting on the planet, second only to oil and gas, and greenhouse gas emissions from textile dyeing at around 3% of global emissions outweigh that of all international flights and maritime shipping combined, it is an industry that can also reduce CO2 emissions the fastest, just by changing the way it dyes fabrics.  

Alchemie Technology, an innovator of low energy, waterless, textile dyeing and finishing technology, is calling on COP26 leaders to support the global fashion industry in the adoption of new manufacturing technology, which will dramatically reduce carbon emissions and fashion’s impact on climate change.

While the fashion industry is one of the most polluting on the planet, second only to oil and gas, and greenhouse gas emissions from textile dyeing at around 3% of global emissions outweigh that of all international flights and maritime shipping combined, it is an industry that can also reduce CO2 emissions the fastest, just by changing the way it dyes fabrics.  

Fabric dyeing is the most polluting part of fashion and activewear manufacturing, involving industrial scale dye baths and huge amounts of dye chemicals, steam, electrical power, and consequent high CO2 emissions.  Repeated washing of the dyed fabric, required to remove dye residue, is responsible for 20% of the world’s wastewater pollution and excess dye is discharged into waterways, affecting the health of some of the world’s poorest communities. In more regulated areas, water pollution is reduced through reliance on energy intensive water treatment plants.

However, an environmental step change can be achieved by adopting new digital technology that can dye fabrics with an 85% reduction in energy consumption and a dramatic 95% reduction of the 1.3 trillion litres of water currently used by the industry each year.

For example, dyeing one polyester shirt using current methods generates 4.5 litres of wastewater and produces 0.17 Kg of CO2, compared to low energy digital technology, which uses less than 0.2 litres of water and reduces carbon emissions to 0.03 Kg.  Multiply these numbers by the billions of garments dyed each year and the scale of the environmental problem, if nothing changes, is clear to see. Equally, the amount by which the textile industry can improve its carbon footprint is dramatic and can be done quickly if action is taken now.

Source:

Alchemie Technology Ltd

(c) Picanol. Connect generation - PicConnect enabled (BlueTouch display).
Connect generation - PicConnect enabled (BlueTouch display)
08.11.2021

Picanol: New Connect generation of airjet and rapier weaving machines

Picanol has introduced its latest generation of airjet and rapier weaving machines, which have been called the “Connect” generation. These new generation weaving machines focus on connectivity and an increased level of data availability. With this new generation, Picanol is launching several new functionalities such as a digitalized Gripper stroke setting, Gripper tape monitoring, Climate control, Shed angle measurement, and fully integrated Power monitoring.

Picanol has introduced its latest generation of airjet and rapier weaving machines, which have been called the “Connect” generation. These new generation weaving machines focus on connectivity and an increased level of data availability. With this new generation, Picanol is launching several new functionalities such as a digitalized Gripper stroke setting, Gripper tape monitoring, Climate control, Shed angle measurement, and fully integrated Power monitoring.

“Following the successful launch of our digital platform PicConnect earlier this month, we have now released a new generation of weaving machines, which are known as the Connect generation. Our Connect generation weaving machines can provide the correct data and are loaded with new and never-before-seen functionalities. This is clear proof that for Picanol “Driven by Data” is not just a slogan but a commitment. Not only have these innovations allowed us to make big improvements when it comes to our four design principles – Smart Performance, Sustainability Inside, Intuitive Control, and, of course, Driven by Data – but when combined with our new digital platform they will allow you to amplify your own intuition.” comments Johan Verstraete, Vice President Weaving Machines.

From now on, the range of Picanol weaving machines will have the “Connect” suffix. For the airjet weaving machines, this means: OmniPlus-i Connect and TerryPlus-i Connect, while for the rapier weaving machines, this means: OptiMax-i Connect and TerryMax-i Connect. These new machines are built around Picanol’s four main design principles:

Smart Performance
On the OptiMax-i Connect, Picanol has introduced a lubrication monitoring sensor in combination with a temperature sensor. The combined data they provide allow the user to make sure the gripper tapes are in optimal condition for maximum performance. As an option, a gripper stroke measurement sensor is also available. This not only dramatically simplifies the setting of the gripper stroke, but also enables the user to realize higher machine speeds when weaving reduced widths – a pure extra output combined with more user-friendliness.

Sustainability Inside
Even though it was 25 years ago that the Sumo Drive concept was launched, it remains the most powerful, versatile and energy friendly machine drive available. And it has been even further optimized. It features an optimized sheet metal package for lower energy consumption, optimized oil cooling circuit for a better performance and a built-in temperature monitoring. Moreover, the Connect machines can be equipped with a Power monitoring module, which allows the user to keep track of the power consumption of each machine over time. Every Connect machine also has a built-in ambient temperature and humidity sensor, which will help to optimize the climate control in the weaving shed at the lowest cost. And as raw material is the biggest cost factor, each machine can also be equipped with raw material use monitoring.

Driven by Data
As the machine has more sensors than ever before, it also generates more data. To enable a fast reaction to all these sensor data, the BlueBox control unit has been further optimized: better heat management guarantees short reaction cycles combined with the long lifetime of components. To have a good view of all of the data generated, a special sensor dashboard screen is available in the BlueTouch display: with a simple touch of the screen, the current and historical power consumption, temperature, humidity, material consumption, and – on the OmniPlus-i Connect – also the air consumption, can be monitored. The BlueTouch display is now also equipped with an Action center, an electronic logbook where all actions such as maintenance interventions can be logged or scheduled beforehand. The machine manual is now available on the BlueTouch display, and with the context-based help function the help pages related to the operation the user wants to perform appear with one touch of his/her fingertip. The built-in web browser even allows the user even to consult, for example, tutorial videos on the web to guide them through a setting procedure.

Intuitive Control
The Connect generation was designed to focus on what really matters: weave the highest possible grade A fabrics at minimal costs. A large set of tools have been installed to facilitate this goal. One of the most remarkable ones is the Harness frame stroke measurement – until recently, it was only available on the revolutionary SmartShed, but it is now also available on the cambox and dobby machines. Combined with the shed visualization and simulation, it offers a quantum leap in terms of optimizing the user’s shed settings without losing any time or taking any risks. The colors of the programmable Smart signal lights with stop timing functionality are now repeated around the push buttons, allowing even better visibility and the prioritization of interventions by the weaver. A full-fledged Access control system not only limits the access to certain pages and settings depending on the user, but also allows a tailored dashboard to be established for each user profile.

Source:

Picanol

Photo: Messe Frankfurt
08.11.2021

Techtextil India: Hybrid exhibition in November

India’s leading trade fair in technical textiles, nonwovens and composites, Techtextil India, is ready to make a comeback through its hybrid edition launch from 25 – 27 November 2021. With a series of live product demonstrations, insightful knowledge sessions and B2B networking opportunities, the multimodal trade fair will provide a strong avenue for technical textile professionals to reimagine their business potential.
 
After a successful grand edition in 2019, Techtexil India is all set to return for the very first time since the pandemic. The three-day exhibition will be hosted in a hybrid format from 25 – 27 November 2021, Bombay Exhibition Centre, Goregaon which will unite technical textile players from across its varied application areas. Top technical textile brands including JB Ecotex, PARK Nonwoven, Loyal Textiles Lenzing, Mehala, Meera Industries, amongst many others will showcase their latest products at the hybrid fair. Moreover, leading German brands exhibiting at Techtextil India 2021 will be hosted under the German pavilion.

India’s leading trade fair in technical textiles, nonwovens and composites, Techtextil India, is ready to make a comeback through its hybrid edition launch from 25 – 27 November 2021. With a series of live product demonstrations, insightful knowledge sessions and B2B networking opportunities, the multimodal trade fair will provide a strong avenue for technical textile professionals to reimagine their business potential.
 
After a successful grand edition in 2019, Techtexil India is all set to return for the very first time since the pandemic. The three-day exhibition will be hosted in a hybrid format from 25 – 27 November 2021, Bombay Exhibition Centre, Goregaon which will unite technical textile players from across its varied application areas. Top technical textile brands including JB Ecotex, PARK Nonwoven, Loyal Textiles Lenzing, Mehala, Meera Industries, amongst many others will showcase their latest products at the hybrid fair. Moreover, leading German brands exhibiting at Techtextil India 2021 will be hosted under the German pavilion.

The conjunction between the physical exhibition and the online business matchmaking platform will make way to a wider range of networking. Local and international visitors who are unable to attend the venue will be able to witness the exhibition virtually through the ‘MFI virtual app’ which will host live knowledge sessions and product demonstrations for visitors. The two-day multimodal trade fair allows the visitors to search for specific products like fibers, yarns, nonwovens, machinery, coated textiles with easy-to-use filters further to which they can share their query or connect directly with the respective exhibitors.

At the same time, visitors attending the venue will be welcomed under a well-organised physical exhibition following the government-authorised safety protocols of ‘MFI SafeConnect’. These protocols will enable visitors to engage in secure face-to-face interactions with exhibitors and witness the latest technical textile technologies and innovations in-person.

Alliance with the Government of Tamil Nadu
In a bid to strengthen indigenous production through the state and attract investors, the nodal agency for investment promotion and facilitation for the Government of Tamil Nadu – Guidance has signed up for Techtextil India 2021. Furthermore, technical textile players from Tamil Nadu such as Cyber Textiles India Pvt Ltd, Jayashree Spun Bond, Lenzing Ag India, Liester Technologies, Loyal Textile Mills Ltd, Milltex Engineers Pvt Ltd, Superfil Products Pvt Ltd, Uster Technologies (India) Pvt Ltd have also confirmed their participation for the exhibition.
Announcing a close co-operation with Messe Frankfurt India for the 2021 edition, Ms Pooja Kulkarni, IAS MD & CEO, Guidance Tamil Nadu, stated: “While there are several inherent advantages for the growth of technical textiles in Tamil Nadu specifically, many raw materials used in the production of sanitary products, artificial ligaments, seat belt webbings, airbags are still heavily imported. In this context, the alliance with Techtextil India Forum can help us reduce import dependency and bring investments in R&D, manufacturing, innovation by partnering with global technical textiles companies.”

With 50% of India’s textile mills in Tamil Nadu and complementary clusters of knitting, weaving and medical devices manufacturing in Coimbatore, and Tiruppur, the region provides immense opportunities for Meditech investments. Two petrochemical and refinery units – One in Cuddalore and another in Nagapattinam by CPCL is in the process of being established in Tamil Nadu. These units will enable availability of MMF raw material for the textile industry across the state. Hence, manufacturing in Tamil Nadu can be a win-win arrangement for investors as India provides access to the burgeoning market as well.

International expertise with German pavilion
Techtexil India 2021 edition will feature an exclusive German Pavilion showcasing products and technologies from top German manufacturers, including Autefa Solution Germany GmbH, DILO Systems GmbH, Emtec Electronic GmbH, Georg Sahm GmbH & Co, Karl Mayer Verwaltungsgesellschaft mbH, Merz Maschinenfabrik GmbH and Oerlikon Barmag Zweigniederlassung der Oerlikon Textile GmbH & Co.

Source:

Messe Frankfurt (HK) Ltd

08.11.2021

Composites Evolution showcased prepregs and new thermoplastic unidirectional tapes

Composites Evolution exhibited at the Advanced Engineering 2021 show on 3rd - 4th November highlighting its range of prepreg and introducing a new thermoplastic tape manufacturing capability.

Composites Evolution is a developer, manufacturer and supplier of prepregs for the production of lightweight structures from composite materials. A flexible approach allows Composites Evolution to offer short lead times and low minimum order quantities, while decades of combined expertise ensure that in-depth technical support is on-hand when customers need it.

Showcased was a battery box from a high-performance luxury electric vehicle manufactured from Evopreg® PFC bio-based, fire-resistant prepreg, a rear wing from a Ginetta G56 GTA GT4 race car utilising Evopreg® ampliTex™ natural fibre prepreg, and parts fabricated from the company’s newly-launched Evopreg® PA thermoplastic tape range.

Composites Evolution exhibited at the Advanced Engineering 2021 show on 3rd - 4th November highlighting its range of prepreg and introducing a new thermoplastic tape manufacturing capability.

Composites Evolution is a developer, manufacturer and supplier of prepregs for the production of lightweight structures from composite materials. A flexible approach allows Composites Evolution to offer short lead times and low minimum order quantities, while decades of combined expertise ensure that in-depth technical support is on-hand when customers need it.

Showcased was a battery box from a high-performance luxury electric vehicle manufactured from Evopreg® PFC bio-based, fire-resistant prepreg, a rear wing from a Ginetta G56 GTA GT4 race car utilising Evopreg® ampliTex™ natural fibre prepreg, and parts fabricated from the company’s newly-launched Evopreg® PA thermoplastic tape range.

Composites Evolution has a family of specialist prepregs for various applications, including Evopreg® EPC epoxy component prepregs which are a range of pre-impregnated fabrics suitable for moulding into high-performance, lightweight, structural components; Evopreg® EPT epoxy tooling prepregs which have been designed to help composite tooling manufacturers improve the flexibility and efficiency of their tooling manufacturing processes; and Evopreg® PFC fire-retardant prepregs a 100% bio-derived alternative to phenolics for applications where fire performance is a critical requirement.

Evopreg® ampliTex™ combines Composite Evolution’s high-performance Evopreg® epoxy resin systems with Bcomp’s award-winning ampliTex™ flax reinforcements, to deliver a family of materials which offer outstanding performance for component applications.

Composites Evolution launched their new range of Evopreg® PA Thermoplastic Tapes at Advanced Engineering; these are manufactured from polyamide-6 (PA6) polymer with unidirectional carbon fibre and are suitable for automated tape laying, winding and compression moulding into high-performance, lightweight components.

Source:

Composites Evolution Ltd