From the Sector

KARL MAYER GROUP has developed a sophisticated system for considerable energy savings when operating the cylinder dryers in its PROSIZE® sizing machines and BLUEDYE dyeing plant.

Saving costs with inline energy recycling
The innovation is called CASCADE and focuses on steam as a heating medium in cylinder dryers. And for good reason: according to the IPCC report by ITMF Zurich, one tonne of steam cost between USD 20 and just under USD 27 internationally in 2021. The new solution relies on reuse to reduce the amount of process energy required.
"CASCADE recirculates parts of the process steam in cylinder dryers, enabling genuine, efficient energy recycling within the machine," explains Karl-Heinz Vaassen, Head of Textile Drying at KARL MAYER.
The customer benefits from significantly lower energy costs and CO2 emissions. With a view to the Asian market, a dryer with 14 cylinders and a running time of 7,000 working hours can achieve cost savings of up to USD 17,000 per year.

Precise, real savings values are available when looking at the machine dashboard. A sensor provides real-time data on the amount of steam circulating in the circuit, from which the corresponding reduction in CO2 equivalents can be calculated.

Utilizing the pressure drop
CASCADE reuses part of the invested process energy and uses the flash-steam in conjunction with the pressure ratios, which - nomen est omen - decrease in cascades in the different zones of the cylinder dryer.
The highest working pressure prevails in the first cylinder section. The heat transfer medium steam emits large amounts of energy for yarn drying and condenses without temperature loss.

The resulting hot condensate is not immediately discharged from the machine, but is instead fed into a flash tank, where vapor exhaust is formed as a result of the pressure reduction. In conventional systems, the carrier medium for gases is only created in the return line towards the boiler house and is eliminated as undesirable. Instead of being utilised in the process, it escapes into the environment. With the CASCADE system, this "freshly recycled steam" is used for the heat supply in the second cylinder section, but not without prior treatment.

In the system patented by KARL MAYER, the recycled steam is intelligently mixed with live steam and thus raised to the level of the required process conditions for use in the cylinder section at the end of the dryer. Here, the fabric moisture is reduced to the desired residual value at medium pressure and temperature conditions.

Market launch is underway
CASCADE was filed for patent by the KARL MAYER GROUP. It was published in September 2023.
The innovative solution at no extra charge was presented at ITM 2024 in Istanbul and was a visitor highlight at the KARL MAYER GROUP stand.

From January 2024, CASCADE will be part of the PROSIZE® as standard. The first sizing machine with the upgrade for greater energy efficiency will be delivered in the second quarter of this year. It will go to a manufacturer in Europe. In the next step, CASCADE will be integrated into other dryer types and will also be available for the BLUEDYE.

Mahlo will be showcasing its comprehensive portfolio of solutions with its partner Masters Limited at the upcoming ITM trade show, scheduled from 4th to 8th June in Istanbul.

The Turkish textile industry continues to experience growth and innovation, making events like ITM crucial for industry players to connect and explore advancements. Fabric distortion remains a common challenge in textile production, impacting product quality and efficiency. Additionally, sustainability and resource optimization are increasingly vital considerations for manufacturers aiming to maintain profitability.

Mahlo offers a range of solutions tailored to different textile structures, from heavy carpets to delicate fabrics. The company's products encompass everything from distortion detection sensors to fully automated straightening systems, customizable to individual production requirements. Moreover, Mahlo's latest generation of straighteners, sensors, and control loops are equipped for Industry 4.0 integration, enabling remote access and real-time monitoring for enhanced efficiency and productivity.
As the textile industry continues to evolve, Mahlo remains at the forefront, providing innovative solutions to meet the changing demands of modern production.

ITM, to be held in Istanbul at the beginning of June, will once again see a strong participation of VDMA member companies. Almost 90 exhibitors from Germany will exhibit at the trade fair, most of whom are members of the VDMA. In addition to the VDMA member companies exhibiting with their own booth, numerous VDMA members will be represented in Istanbul via agents. They cover nearly all different machinery chapters with a focus on spinning, nonwovens, weaving, knitting, warp knitting and finishing.

In Istanbul, the VDMA members will show their latest innovations. In technological terms, significant trends are digitalisation and automation. These themes have been present for some time but will continue to play a central role in meeting the challenges for many years to come. Another trend that has also been around for a while is sustainability. Today it is much more than a buzzword: Efficiency in energy, raw materials or water as well as recycling are not feel-good issues but have a real economic and social background.

For the textile machinery manufacturers organised in the VDMA, Turkey is a major trading partner. In 2023, textile machinery and accessories worth approximately 350 million euros were exported from Germany to Turkey, which made Turkey the second biggest sales market for German companies. After three years in which China was the most important supplier of textile machinery to Turkey, Germany has now regained this top position.

Turkey is at the doorstep of Europe, which gives Turkish textile producers a powerful geographic advantage over Asian sourcing destinations. The textile companies in the region have a deep experience and know-how in making the highest quality textile and apparel for leading markets of Europe and employs a young, dynamic, and well-educated workforce.

But ITM is not just a place for visitors from Turkey, as Dr. Harald Weber, Managing Director of the VDMA Textile Machinery Association explains: “It should not be forgotten that ITM not only attracts visitors from Turkey, but also from the Middle East, Central Asia and North Africa. Turkey's proximity to the European Union and its fully integrated textile value chain also make it interesting in terms of the EU's strategy for sustainable and circular textiles and the increasing importance of recycling in the future.”

The Italian Trade Agency (ITA) decided to participate in the ITM 2024 Exhibition this year with the Italian pavilion.

ITM 2024 International Textile Machinery Exhibition is preparing to host textile technology leaders in Istanbul on June 4-8, 2024. ITM 2024, which will be organized this year with the motto 'Discover the Future', will offer opportunities to discover the latest innovations in the sector, establish new business contacts and shape the textile world of the future together. The products to be exhibited at ITM 2024 Exhibition, which will bring together nearly 1300 domestic and foreign companies, will meet with thousands of buyers and visitors.

The Italian Trade Agency (ITA) is the governmental agency that supports the business development of Italian companies abroad and encourages the attraction of foreign investments to the country. ITA has decided to participate in the ITM 2024, which will be held at Tüyap Fair and Congress Center, as a pavilion. With this decision, ITA aims to further strengthen its presence in the sector and in Turkey.

ITM Exhibitions will open its doors to host "ITM 2024 International Textile Machinery Exhibition" from June 4-8, 2024. Preparations are in full swing for the organization, where textile technology leaders will bring the latest products together with their visitors for the first time.

The ITM team focused on advertising and promotional activities in order to host thousands of visitors and sector investors from all over the world at the ITM 2024 Exhibition, which halls were almost full due to intense participation demands. In this context; 'ITM 2024 Video', which tells the story of the increasing success of ITM exhibitions over the years and which is eagerly awaited by the whole sector, has recently been published. The video, which was published in Turkish and English on social media accounts such as YouTube, LinkedIn, Instagram, Twitter and Facebook, was viewed by more than 30 thousand people in total and received great appreciation from the viewers.

“Discover the Future!” in the video prepared with the main theme “Discover innovations, technologies, the future...” and including clues about the ITM 2024 Exhibition, was revealed as follows:
The textile sector is among the souls of the economy with its production capacity, export volume, and contribution to employment. Many R&D centers around the world and in Turkey are breaking new ground by taking their work and innovations one step further every day. Textile technology leaders are developing technologies that consume less water and energy, are easy to use, are software and automation supported, keep up with trends and respect the environment while doing so. Industry stakeholders, especially textile manufacturers, are now curious about the answer to this question: 'What will be the future of the textile industry, which is digitalizing, complying with sustainability principles, and signing groundbreaking innovations? This question will be answered at ITM 2024, which will host the latest innovations, technologies, artificial intelligence-supported machines, software and design excellence devices in textile machinery.

From April 25^th to 27^th, 2023, the Institute of Textile Machinery and High Performance Material Technology (ITM) of TU Dresden will be exhibiting at the pavilion SAXONY! at JEC World 2023.

The ITM will provide a comprehensive overview of its current research in the field of machine and product development along the entire textile process chain.

The upcoming JEC 2023 exhibition will highlight innovative Customised Connective Cores (CCC), which are custom-made core-insert structures additively manufactured using cellular metal and a form-fit integrated insert. These CCCs can be seamless integrated either as patches or as full-surface core material into lightweight panels, offering significantly improved load-bearing behavior (especially 4 times the load-bearing capacity and fail-safe behavior) compared to existing technologies. This breakthrough opens up new possibilities for fastening lightweight panels.

Another highlight at the exhibition is the repair process for fibre-reinforced composites (FRP) developed at the ITM. Instead of mechanically grinding the damaged area, the matrix in the repair area is locally dissolved using a UV-rays-induced depolymerisation process. Damaged fibres can thus be replaced by a customized repair patch. Free yarn ends on the textile repair patches are spliced with the UV-exposed yarn ends in the repair area using an adapted splicing process. In this way, a very clean, simplified and mechanically improved repair area can be achieved compared to the state of the art.

The diverse possibilities offered by the structure and process simulation of textile high-performance materials and textile manufacturing processes will also be presented. By means of multi-scale modelling and simulation, a profound understanding of materials and processes is achieved at the ITM. Finite element models on the micro, meso and macro scale have been developed and validated for this purpose. Examples from current ITM research projects demonstrate the various possibilities and areas of application of modern simulation methods in the field of textile technology.

Moreover, an innovative process for the integral manufacturing of 3D rib-stiffened preforms with complexly arranged stiffeners in 0°, 90° and ± 45° orientation was developed and successfully implemented at the ITM. Due to the process-integrated structure fixation and the continuous fibre reinforcement between shell and rib structure, the 3D preforms are perfectly suited for the production of highly load-bearing FRP components with increased bending stiffness, which will be exhibited at JEC. Hence, the lightweight construction potential of high-performance fibres can be fully exploited.

A successfully established development are partially flowable 2D textile reinforcement fabrics that are continuously manufactured in one single process step. For this purpose, the entire process chain was developed at the ITM, which allows a cost-effective and high-volume production of load-bearing thermoplastic 3D FRP components with continuous fibre reinforcement between shell and stiffeners.

At JEC 2023, the ITM will also present a partially embedded textile latice girder as reinforcement for carbon concrete applications, which was produced by means of an innovative textile manufacturing process based on the multiaxial warp knitting technology. Through the development of a customized warp insertion, manipulation and take-off system as well as appropriate shaping methods, it is now possible to produce tailored textile semi-finished products, e.g. for use in wall and ceiling panels. These textile latice girders represent a resource-saving alternative to conventional steel girders due to the reduced among of concrete required and the additional cavity for media and cable guidance.

The integration of textile actuators and sensors in FRP provides structures with additional functionalities. The research and application of such interactive FRP with different matrix materials (e.g. with thermoset, elastomer or concrete matrix systems) for structural health monitoring or adaptive systems is one of the key research areas of the ITM.

Moreover, the development and implementation of innovative yarn constructions based on recycled high-performance fibres (e.g. rCF, rGF, rAR) for sustainable FRPs is successfully promoted at ITM. By use of a special carding machine, recycled fibres are opened up, separated and joined to form a wide, uniform ribbon. Subsequently, innovative hybrid yarn constructions made of evenly mixed recycled high-performance and thermoplastic fibres with variable fibre volume fractions can be manufactured by means of various spinning technologies. Selected yarn constructions and components will be showcased at JEC.

ITM - International Textile Machinery Exhibition, which is one of the world's most important exhibitions in its field and carries its success beyond its borders, will be held in a country other than Turkey for the first time next year under the name 'ITM Uzbekistan'. 'ITM Uzbekistan 2023 Exhibition', which will be held in Uzbekistan New Expo Center on September 12-15, 2023, will bring together buyers from Central Asia and Turkic Republics with the world's most important textile and garment technology manufacturers.

ITM Uzbekistan to be organized in odd years
'ITM Uzbekistan', organised by Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc., will be first held in September 2023, from 12th to 15th, and thenorganized in the following odd years such as 2025, 2027, and so on. The exhibition calendar was created by taking into account the dates of the exhibitions organized in the same sector in different countries of the world and in Europe and the benefits of the sector.

Tashkent New Expo Center
New Expo Center, built in Tashkent, the capital of Uzbekistan, will host the most important events of both Central Asia and Turkic Republics. New Expo Center, where many national and international events will be held, will be the gateway of Central Asia to the world. The exhibition center, consisting of a total area of 44 thousand square meters and two stages, was built with the latest technology, taking into account all needs. The new exhibition center, which includes cafes/restaurants, resting areas, meeting, congress, seminar and exhibition halls, is an important attraction center with its proximity to the new airport under construction in the capital and the facilities where the international Olympic Games will be held.

ITM 2022 hosted textile technology leaders in Istanbul for 5 days, presenting the latest innovations in every field of textile from weaving, knitting, yarn, digital printing, finishing to denim. The ITM 2022 Exhibition, where a business volume of over 1.5 billion Euros was created in 5 days, accelerated the Turkish and world economy.

Organized by the partnership of Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc., ITM 2022- International Textile Machinery Exhibition was held at Tüyap Fair and Congress Center between 14-18 June.  ITM 2022 Exhibition, attended by 1280 companies and company representatives from 65 countries, was visited by 64,500 people from 102 countries, consisting of 44% international and 56% domestic visitors.

Turkey became a Supply Center at the ITM 2022 Exhibition
The successful sales graph achieved at the ITM 2022 Exhibition proved that the difficulties experienced due to the pandemic for the last 3 years have been left behind. Turkey has become a supply center for European, Middle Eastern and African countries, especially with the disruption of the supply chain in Far East countries, including China. The profile of the professional visitors visiting the ITM 2022 Exhibition revealed that in the new world order that has shifted after the pandemic, the trade network has also changed hands and new players have appeared on the scene. The fact that manufacturers from all over the world such as Andorra, Angola, Honduras, Peru, Seychelles, Sierra Leone, Brazil, Sri Lanka, Tanzania, Egypt, Iran, and Oman purchased a large number of machinery and signed collaborations at the ITM 2022 Exhibition has proven this.

Exhibitors of ITM 2022 enlarge their stands for ITM 2024
Many company officials, who stated that they have achieved a sales graphic far above their expectations starting from the very first day of the ITM 2022 Exhibition and that they have hosted visitors from all over the world, decided to enlarge their stands at the ITM 2024 Exhibition. During the exhibition, companies visited the registration application points and applied for ITM 2024 participation.

The next meeting of the ITM and HIGHTEX Exhibitions will be held in Istanbul between 4-8 June 2024.

ITM 2022, the first major international textile machinery exhibition to be held in the world after a 3-year hiatus during the pandemic process, is getting ready to open its doors. Bringing the leading brands of textile technologies together in Istanbul, ITM 2022 will host world launches and numerous collaborations for 5 days.

ITM 2022- International Textile Machinery Exhibition, organized in partnership with Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc, will open its doors at Tüyap Fair and Congress Center between 14-18 June. For ITM 2022, which will be held in 12 halls on an area of 120,000 m2; hums of 1280 participating companies from more than 40 countries continues. Tüyap Fairground, where thousands of people sweat for stand setups, is getting ready for the big meeting. ITM 2022, where all halls have reached 100% occupancy rate and 1280 exhibitor companies are located, will also attract attention with the stand areas and machine parks that the manufacturers have enlarged compared to the previous exhibitions.

Companies will showcase their state-of-the-art technologies for the first time at ITM 2022
Many companies that focus on product development and new productions under pandemic conditions will have the opportunity to introduce their products to their customers for the first time in 3 years at the ITM 2022 Exhibition. Company owners, managers, employees and sector representatives visiting the exhibition will have the opportunity to see the latest technological innovations for the first time and witness their world launches.

Sector representatives, who will open up new horizons in their minds about textile technologies, will sign new products by transforming the extraordinary and original ideas that they have obtained at the ITM 2022 Exhibition into design. Participating companies will also update their machines in line with the demands and needs from the sector representatives and lead the development of new technologies.

Significant Contribution to Exports Aimed with Machine Sales and New Investment Decisions
The textile industry, which is among the locomotive sectors in Turkey's exports, has made a significant contribution to the Turkish economy, especially with the performance increase it has achieved during the pandemic period. Having achieved an increase of up to 40 percent in its exports of textiles and raw materials, Turkey also managed to increase its exports of medical textiles, technical textiles and home textiles. The industry will further increase this success with the collaborations to be realized at ITM 2022. The textile machinery industry will gain great momentum with the machinery sales and new investment decisions to be made at the exhibition.

ITM 2022, which will be attended by many domestic and foreign companies and visited by thousands of people, will be an organization where both domestic and foreign companies will make sales amounting to millions of Euros and many business connections will be realized.

Intense Interest from Trade Delegations
Trade delegations from dozens of countries are requesting to attend the ITM 2022 Exhibition, which is included in the ‘Domestic Organizations Covered by State Incentives’ list by the Ministry of Commerce. Bangladesh, India, Iran, Serbia, Czech Republic, Pakistan, Indonesia, Ethiopia, Malaysia, Mexico, Egypt and Vietnam are among the countries that requested procurement delegations. The intense application of visitors to consulates and commercial attachés from all over the world clearly reveals that ITM 2020 will host a large number of visitors.

ITM 2022 Exhibition Prepares to Break Both Exhibitor and Visitor Records
Company owners, company representatives and visitors left the 2018 edition of the ITM Exhibition very satisfied. ITM 2018 Exhibition, attended by 1150 companies and company representatives from 64 countries and visited by approximately 60 thousand people from 94 countries made a significant contribution to the export records of the textile industry that year. At the ITM 2022; It is getting ready to break new records with the number of participants and visitors coming from Turkey and abroad.

Technical Textiles and Nonwovens Industry Will Meet at HIGHTEX 2022 Exhibition
On the other hand, HIGHTEX 2022 Exhibition, which will be held simultaneously with the ITM 2022 Exhibition, will be an exhibition where Nonwoven products, raw materials used in their production and the state-of-the-art technologies will be exhibited. HIGHTEX 2022 Exhibition, which is the first and only in its field in Turkey, will host a record number of participants and visitors in parallel with the increase in demand for technical textiles. At the HIGHTEX 2022 Exhibition, companies operating in many sectors, from medical textiles to hygienic textiles, from agricultural textiles to geotextiles, will exhibit their latest products and production technologies. Nonwoven manufacturers will come together with the global players of the sector and have the opportunity to both invest in technology and introduce their newest products.

The German machinery producer BRÜCKNER used exactly these chances and repositioned itself during the pandemic period. For more than 70 years, the family-run company has been specialized in individual finishing concepts for textiles, technical textiles, nonwovens and floor coverings. The current challenges in the textile industry are serious. The clear increase of the energy costs and the general uncertainty of the energy supply as well as political requirements make a profitable textile production more and more demanding for many companies.

The company responds to this with a newly developed stenter concept with double heating system. Depending on availability, the lines can be operated with gas or oil, but also other combinations with steam or renewable energies are possible. This means that production delays and machine downtimes can be avoided as far as possible. In addition, developed intelligent assistance systems for its machines have been developed that support the machine operator in using the best possible process to operate the line as energy-efficiently as possible. Further energy savings are possible with new energy-efficient motors or heat-recovery and exhaust air cleaning systems. This also helps to avoid harmful emissions.

But many textile producers are also focusing on reducing chemicals. For this purpose, BRÜCKNER's further developed ECO-COAT minimum application unit can make a decisive contribution. Knitted and woven fabrics, but also nonwovens can be finished on one or both sides via different fabric paths. With the minimum application via an engraved roller, a single-sided application of up to 100 g/m² can be achieved. A double-sided and higher application quantity is achieved, for example, by impregnation in the nip. Irrespective of the selected fabric path, a very small liquor reservoir means that only minimal quantities of waste water are produced when changing batches or liquors, and the use of chemicals can also be significantly reduced. In addition, less water has to be evaporated in the subsequent drying process than, for example, in the case of impregnation in a water bath, so the energy requirement is significantly reduced.

On the two upcoming trade fairs ITM in Istanbul and TECHTEXTIL in Frankfurt in June, interested customers can personally get an idea of BRÜCKNER's new developments.