From the Sector

Huntsman Textile Effects will be highlighting its extensive range of HIGH IQ® intelligent effects at the Functional Fabric Fair power by Performance Days in New York this July. Huntsman’s comprehensive range of non-fluorinated Durable Water Repellency technology will also be presented at the upcoming show.

Through our cutting-edge technology and expert technical knowledge, High IQ® delivers the industry’s leading range of innovative, eco-friendly intelligent textile effects. Fabrics treated with our intelligent effects are sustainable textile products that deliver the performance and benefits consumers expect of high-quality brands.

At ITMA 2019 in Barcelona from June 20-26th, Goller will introduce the new Knit Merc for achieving the highest quality mercerization of knitted fabrics at the lowest tension and with under 3% variation in dimensional stability with high grade fabrics, for perfect dyeing results every time.

Mercerization is an essential textile finishing step for all cotton and cellulosic fibre-based fabrics in order to improve dye uptake and tear strength while reducing fabric shrinkage and imparting a silk-like lustre to the materials.

The Knit Merc is the result of intensive R&D developments at Goller and follows the successful introduction to the market of the company’s Sintensa Cyclone drum washing compartments for achieving the highest washing efficiency at the lowest tension.

The Knit Merc being exhibited at ITMA 2019 can accommodate 8.4 metres of fabric in its impregnation compartment and a further four metres in its first chain section to achieve a production speed of 25m/min at 30 seconds dipping time.

It is designed for dry-on-wet mercerizing, either cold or hot, and is equipped with an inlet combination of scroll and slat rollers for fabric guidance, a Tandematic uncurler in front of a rubberized de-airing roller and a grooved 320mm bottom roller with 320mm and 600mm perforated upper drums.

It benefits from automatic tension regulation and the low liquor content is ensured by the integrated lye tank and automatic circulation and filtration units.

An 8-ton high efficiency squeezer is stationed at the exit before the chain section and a 5-ton squeezer at the exit of the chain field.

Further fabric control and stability is provided by a cast iron pin chain with automatic optical and mechanical sensors, the Tandematic uncurler, an overfeed device and a driven belt arrangement for fabric support.

Printing textiles and hard substrates with impressive results: this is what Transjet dye sublimation papers from Sappi stand for. The new Transjet Drive is a sublimation paper optimised for industrial printers with a glue-belt system and will be showcased for the first time at FESPA trade fair in Munich. Sappi will also be presenting its inkjet papers for large-format applications, the Fusion Topliner containerboard and various silicone base papers at Stand B6-B30.

A highlight is the Transjet portfolio, with which fashion and home textiles, hard substrates and sportswear can be customised and personalised in strong colours using transfer printing. These papers are also suitable for soft signage, i.e. textile printing in marketing and advertising.

The new Transjet Drive sublimation paper is primarily tailored to industrial printers with a glue-belt system. The exceptionally smooth reverse side is a key feature. This advantage and the remarkable fast ink-drying on the printed side increase runnability and efficiency during the production process. Optimal cost efficiency and consistent reliability are central benefits for this and all other dye sublimation papers from Sappi. At the same time, they ensure consistent ink transfer with minimal ink consumption, are PE-free and contain 100 percent recyclable pulp.

Techtextil 2019: Schoeller launches its new finishing technology called NanoSphere® Plus. The special effect of this new development is its protection against fingerprints and greasy stains. Furthermore, even after being absorbed by the fabric stains are quickly and easily wiped away without washing.

Every human being leaves its marks. In particular, on daily-use items that are picked up or touched often. Especially on textile surfaces, hand and fingerprints in combination with dirt and dust particles leave an unpleasant, greasy dirt film, which is very difficult to clean.

NanoSphere® Plus, developed by Schoeller Technologies AG, the business unit for technologies at Schoeller Textil AG, works on the basis of a functional chain. Textiles are equipped with a matrix finish to reduce the capillary effect in the textile’s fibers. Especially unpleasant sebum residues and dirt that are often released by finger and handprints are less absorbed by the fabric and can be easily wiped away.

Beside the excellent protection against finger and handprints, textiles with NanoSphere® Plus are additionally water and oil repellent, abrasion resistant and extremely durable. The finishing technology rarely affects the look or feel of the fabric.

Non-washable textiles that are often touched by hands or fingers, or fabrics that are in direct contact with the skin benefit most from this new technology. Therefore, NanoSphere® Plus is ideal for woven fabrics and synthetic leather or synthetic suede for bags, covers of electronical devices, head phones, loud speakers or other items in the field of interior equipment.

• Hexcel’s Composite Innovations For Aerospace, Automotive, Energy And Marine Applications At JEC World 2019 Hall 5 - Stand J41

STAMFORD, Conn. – At this year’s JEC World taking place in Paris on March 12-14, Hexcel will promote a wide range of composite innovations for customer applications in aerospace, automotive, energy and marine markets.

Aerospace Innovations

Hexcel’s HiTape® and HiMax™ dry carbon reinforcements were developed to complement a new generation of HiFlow™ resin systems, producing high quality aerospace structures using the resin infusion process. HiTape® was developed for the automated lay-up of preforms and HiMax™ is a range of optimized non-crimp fabrics (NCF). Both products incorporate a toughening veil to enhance mechanical properties, meeting the structural requirements for aerospace parts.

Visitors to JEC will see an Integrated Wing Panel demonstrator and an I-beam, both made with HiTape® reinforcements, and an Opticoms rib made with HiMax™ NCF. The Opticoms rib and I Beam were both manufactured using C-RTM (Compression Resin Transfer Molding). They were injected with Hexcel’s RTM6 resin in a process taking less than 5 minutes. The total manufacturing cycle for both parts was just 4.5 hours.

Also among the Aerospace exhibits, Hexcel will display a composite petal for a satellite antenna, manufactured by Thales Alenia Space Italia. The petal is part of a set of 24 deployable structural elements that form the large area reflector assembly used on board Low Earth Orbit (LEO) observation satellites. Thales Alenia Space Italia selected Hexcel’s HexPly® M18 prepreg for this application, acknowledging the superior mechanical and outgassing properties provided.

Another Hexcel prepreg application on show is a “zero” frame, manufactured by Aerofonctions for the engine area of Daher’s TBM 910/930 single-engine turboprop aircraft. Hexcel’s HexPly® M56 prepreg was selected by Daher for the “zero” frame – a product developed for Out of Autoclave applications that provides the same high quality and performance as autoclave-cured prepregs, from a simple vacuum bag cure in an oven.

With 50 years of experience behind its comprehensive range of high-strength, high-strain PAN-based carbon fibers, Hexcel continues to innovate, and is introducing two new fibers to its portfolio. HexTow® HM50 combines high modulus and high tensile strength, making it ideal for commercial and defense aircraft and engines. HexTow® 85 was developed specifically to replace rayon-based carbon fiber for ablative applications.

HexTow® carbon fiber holds the most qualified carbon fiber positions on aerospace programs in the industry and is the best unsized fiber available on the market. It provides excellent bonding interfacial properties with thermoplastic matrices and is the best-performing fiber for 3D printing applications.

Additive manufacturing is another area of expertise for Hexcel, using PEKK ultra-high performance polymers and HexAM™ technology to manufacture carbon-reinforced 3D printed parts. This
innovative process provides a weight-saving solution for intricate parts in highly demanding aerospace, satellite and defense applications. HexPEKK™ structures offer significant weight, cost and time-to-market reductions, replacing traditional cast or machined metallic parts with a new technology.

Hexcel is well known for its range of weight-saving, stiffness-enhancing honeycombs and the company adds value by providing a range of engineered core solutions to customers from facilities in the USA, Belgium and the newly opened Casablanca plant in Morocco. Hexcel’s engineered core capabilities enable highly contoured parts with precision profiling to be produced to exacting customer specifications. An example of such a part will be on display at JEC. Made from Aluminum FlexCore®, the part is CNC machined on both sides, and formed and stabilized with both peel ply and flyaway layers of stabilization. Aircraft engines benefit from a number of Hexcel core technologies including HexShield™ honeycomb that provides high temperature resistance in aircraft engine nacelles. By inserting a thermally resistant material into honeycomb cells, Hexcel provides a core product with unique heat-shielding capabilities that allows for the potential re-use of material after a fire event.

Hexcel’s Acousti-Cap® broadband noise-reducing honeycomb significantly improves acoustic absorption in aircraft engine nacelles. The acoustic treatment may be positioned at a consistent depth and resistance within the core, or can be placed in a pattern of varying depths and/or resistances (Multi-Degrees of Freedom and 3 Degrees Of Freedom), offering an acoustic liner that is precisely tuned to the engine operating conditions. These technologies have been tested at NASA on a full engine test rig and meet all 16 design conditions without trade-offs.

HexBond™ – the new name in Adhesives

Hexcel’s range of high performance adhesives has expanded considerably following the company’s acquisition of Structil. The company has now decided to unite the range by marketing all of its adhesive products using HexBond™ branding. The comprehensive range of HexBond™ structural film adhesives, foaming adhesive films, paste adhesives, liquid shims, epoxy fillets and Chromium free liquid primers is suitable for a wide range of applications in combination with Hexcel’s prepreg and honeycomb products.

Automotive Innovations

Hexcel’s carbon prepreg patch technology provides an innovative way of locally stiffening and reinforcing metal parts, providing noise and vibration management functionality. HexPly® prepreg patches consist of unidirectional carbon fiber impregnated with a fast curing epoxy matrix that has self-adhesive properties, enabling it to bond to metal in a highly efficient one-step process. These key technology properties are demonstrated in an 18.5kg aluminum subframe (that is 50% lighter than steel equivalents), which was reinforced with 500 grams of HexPly® prepreg and tested by Saint Jean Industries. The part demonstrates a significant reduction in noise, vibration and harshness (NVH). Other benefits include lower production costs, energy savings, increased driver comfort, production flexibility and part count reduction. With this technology Hexcel is a finalist in the JEC Innovation Awards 2019 in the Automotive Applications category.

HexPly® prepreg patch technology was also applied to a hybrid side sill demonstrator developed with Volkswagen and Dresden University to address future crash test requirements, specifically for electric cars. Combining fiber-reinforced plastic (FRP) with metal, the hybrid construction allows for optimum performance including weight savings, enhanced safety, increased energy absorption, battery protection in a crash situation and production flexibility.

Hexcel will also display a lightweight CFRP transmission crossmember produced from Hexcel’s high performance HexMC®-i 2000 molding compound. The transmission crossmember was developed in partnership with the Institute of Polymer Product Engineering (at Linz University), Engel and Alpex. As the part connects the chassis together and supports transmission it has to be stiff and strong, resisting fatigue and corrosion. Hexcel’s HexMC®-i 2000 was selected as the best-performing molding compound on the market, curing in as little as two minutes to produce lightweight, strong and stiff parts.
To produce the transmission crossmember HexMC®-i 2000 preforms are laid up in Alpex molds and compression-molded in a v-duo press that was tailored for the application by Engel. Ribs, aluminum inserts and other functions can be molded into the part using the single-stage process, reducing component-count. Any offcuts from the preforms can be interleaved between the plies of material to provide additional reinforcement in key areas - meaning that the process generates no waste.

Other Automotive promotions on Hexcel’s stand at JEC World include a composite leaf spring manufactured by ZF using HexPly® M901 prepreg. In contrast to steel leaf springs, composite versions offer many advantages including weight savings of up to 70%, high corrosion resistance, optimized system integration and superior performance. HexPly® M901 prepreg reduces the cure cycle to below 15 minutes and provides 15% higher mechanical performance, with enhanced fatigue properties. It also operates at high temperatures, providing a Tg of up to 200°C following a post cure.

Marine Innovations

Hexcel has a comprehensive range of products aimed at racing yacht and luxury boat builders that include America’s Cup, IMOCA class and DNV GL-approved prepregs, woven reinforcements and multiaxial fabrics for hull and deck structures, masts and appendages.

At JEC World Hexcel will display an IMOCA yacht mast manufactured by Lorima using HexPly® high modulus and high strength carbon fiber prepreg from Hexcel Vert-Le-Petit. Lorima is the exclusive official supplier of masts for IMOCA 60 class racing boats.

Hexcel’s HexTow® IM8 carbon fiber has been selected as the highest performing industrial carbon fiber on the market and will be used by spar and rigging manufacturer Future Fibres to manufacture their AEROrazr solid carbon rigging for all the teams in the 36th America’s Cup.

Hexcel’s HiMax™ DPA (Dot Pattern Adhesive) reinforcements are non-crimp fabrics supplied pre-tacked, allowing multiple fabrics to be laid-up more easily in preparation for resin infusion. Providing an optimal, consistent level of adhesion, they allow a faster and more consistent resin flow, as well as eliminating the use of spray adhesive for a healthier working environment and lower risk of contamination. Simply unrolled and applied to the mold or core layer before the introduction of resin, HiMax™ DPA fabrics are widely used in boat building, where lay-up times can be reduced by up to 50%.

Wind Energy Innovations

Hexcel has developed a range of HexPly® surface finishing prepregs and semi-pregs for wind turbine blades and marine applications. Providing a tough, durable and ready-to-paint surface without using in-mold coats, these products shorten the manufacturing cycle and reduce material costs. HexPly® XF2(P) prepreg is optimized for wind blades and has a ready-to-paint surface, straight from the mold, saving at least 2 hours of takt time.

Polyspeed® pultruded carbon laminates were developed for load-carrying elements in a blade structure and are manufactured with a polyurethane matrix that provides outstanding mechanical performance in terms of stiffness and durability. The blade manufacturing process is optimized, with increased throughput. The pultruded laminates are supplied in coils as continuous cross section profiles.
HiMax™ non-crimp fabrics using E-glass, high modulus glass and carbon fibers are also available in a wide range of unidirectional, biaxial and triaxial constructions. HiMax™ fabrics have applications throughout the turbine, from the stitched carbon fiber UDs used in the main structural elements, to glass fabrics and hybrids for blade shells and nacelles. There are also specialist applications such as lightweight fabrics for heated leading edge de-icing zones.

• conceptual and commercial garments presented at exhibition in London

After two years of research Mistra Future Fashion is honoured to present, in collaboration with Centre for Circular Design at University of the Arts London and Filippa K, an exhibition pushing the limits of ‘fast’ and ‘slow’ fashion. Started in 2017, the industry-embedded project Circular Design Speeds takes a unique systemic approach, showcasing what could be accomplished using existing value chains as well as what the future of sustainable fashion holds. Ground-breaking textile research from University of the Arts London is questioning normative use and design of garments in creating prototypes to be worn across a spectrum of 24 hours to 50 years. By implementing research into existing value chains, Filippa K have produced a coat that is 100% recycled and recyclable, as well as a concept dress that is 100% bio-based and biodegradable. The research results and garments will be presented at the launch event at the University of the Arts London, on November 23rd and open to public on the 24th and 25th of November.

On Friday November 23rd the exhibition Disrupting Patterns: Designing for Circular Speeds opens up at University of the Arts London. The exhibition is the results of a two-year research project called Circular Design Speeds aiming at pushing the limits of ‘fast’ and ‘slow’ fashion by testing new concepts for sustainable design in an industry setting. On display are exploratory prototypes, as well as commercial garments produced by industry partner Filippa K using existing value chains. In addition, research results on innovative materials, consumer acceptance, composting studies and Life Cycle Assessments are presented. The aim of this project is to implement research results in a real fashion industry context, focusing on speed of use and maximising fabric value retention in products.

The Service Shirt developed by Professor Rebecca Earley is designed to last for over 50 years. The concept garment explores the multiple complexities, challenges and opportunities associated with design for circular business models in extended use contexts. The Service Shirt was designed as a ‘deliberate extreme’ to have a total lifecycle of 50 years. This lifecycle includes in-house and external remanufacturing processes, as well as various use cycles – often moving between single ownership and rental and sharing contexts. It becomes the lining for a jacket and then crafted in to fashion accessories, before finally being chemically regenerated in the year 2068.

On the opposite side of the spectrum the Fast-Forward concept, developed by Prof Kay Politowicz and Dr Kate Goldsworthy, explores alternative modes of production and use for a sustainable ‘fast-fashion’ application. Advantages with regards to climate impact are enabled through lighter material choices, nonwoven fabric production, no launder, clear routes to recovery and redistributed manufacturing systems. A sliding scale of ‘speed’ from ultra-fast forward through to a more widely accepted length of use, with adaptations to production processes and end of life, is presented. The prototypes are made from a new bio-based nonwoven material co-developed with Dr Hjalmar Granberg at RISE Research Institute of Sweden & University of the Arts London. The composition of the paper is a mix of cellulose pulp and bio-based PLA fibre, making the garment 100% biodegradable or recyclable in existing paper recycling systems.

Working closely with industry partner Filippa K made commercial testing possible. By implementing research into existing value chains, Filippa K was able to produce a coat that is 100% recycled and recyclable, as well as a concept dress that is 100% bio-based and biodegradable. The garments are a part of Filippa K’s Front Runner series and will be available in selected stores on November 26th. With a focus on products’ length of use and maximizing fabric value retention, Filippa K are dedicated to becoming fully circular by 2030.

“Being part of the fashion industry comes with many challenges, especially when considering the fact that we are the second most polluting industry after oil. Our industry needs to change and we believe adapting to circular models, like nature’s ecosystem, is one important solution. We want to be able to offer beautiful clothing and to make business within the planetary boundaries.”
- Elin Larsson, Sustainability Director, Filippa K

To validate the design research presented, a Life Cycle Assessment was performed on the prototypes. Mistra Future Fashion affiliated Dr. Greg Peters, Chalmers University of Technology, together with additional LCA Researchers at RISE, conclude that the production of fibres and fabrics are the main processes impacting the environment during the garment life cycles. Therefore, to extend the lifetime of existing garments and design for re-use, as done in the Service Shirt, is indeed the superior alternative compared to a reference garment.

“Compared with garments of the same mass, the extended life garments represent a large improvement in environmental performance over the reference garments, outperforming the reference garments in all effect categories. This superiority is primarily a consequence of avoiding garment production via reprinting and reassembly of the initial garment to extend its useful life.”
- Dr Greg Peters, LCA Researcher at Chalmers University of Technology

Another way to circumvent the impacts of fast fashion is to develop materials with considerably lower impacts during production, and which also avoid the barriers to recycling faced by conventional garments. Instead of hinder consumers from buying new, the act of acquiring a new garment could in fact be sustainable. The paper-based short life garments considered in this assessment show considerable impact savings when compare to the benchmark garment. Dr. Peters says,

“The paper-based garments benefit from the lower impacts of the material (fibre production, spinning and knitting) compared with conventional cotton, from their relatively light weight and also on account of the lower impacts in garment production and use.”

Cinte Techtextil China opens its doors next week, with around 480 exhibitors from 22 countries and regions preparing for another successful showcase of the world’s leading textile innovations. Leading international and domestic brands will feature in halls N1 – N3 at Shanghai New International Expo Centre from 4 – 6 September, making Cinte Techtextil the ideal place to make connections and gain insight into Chinese and Asian market trends.

The technical textile industry in the Asia region, and China in particular, has been growing steadily and is predicted to continue doing so. China’s total output of technical textiles and nonwoven products is estimated to account for 30% of global production by 2020, and double that of 2013. This high potential for growth, achieved through investments worth billions of dollars, has drawn attention from European exhibitors, who are set to travel to the region for Cinte Techtextil.

This year’s European Zone will feature around 30 exhibitors from countries including Austria, France, the Netherlands, Sweden, Switzerland and the UK, while further exhibitors can be found in national pavilions from Belgium, Germany and Italy. In addition to this, the Czech Republic will present its debut pavilion, showcasing exhibitors with solutions for technical yarn, fabric processing and nonwoven fabrics.

In addition to this, exhibitors from 12 more countries and regions will present their latest innovations to the market. These include domestic and international exhibitors from China, Hong Kong, India, Indonesia, Israel, Japan, Korea, Saudi Arabia, Taiwan, Thailand, Turkey and the US.

Belt and Road: a success story for Buildtech
Following higher regulations and quality standards that aim to exceed Western levels, demand is high in China for production machinery. What’s more, with the national nonwovens market displaying particularly fast growth, Cinte Techtextil has attracted some of the world’s leading nonwoven and weaving machinery brands.

The fair will showcase leading global exhibitors across 12 application areas. Two areas to watch out for include Buildtech and Mobiltech, which are both performing well in Asia and specifically in China. The Belt and Road initiative brings Buildtech a great deal of benefits through China’s enormous investments in global infrastructure. Adding to this, China’s automobile production has been increasing 3% year-on-year, with particularly high growth seen in new-energy vehicles, SUVs and commercial vehicles. China has become the world’s largest auto producer, and this has been boosting progress in the Mobiltech category.

Cinte Techtextil fringe programme a hub of industry insight
A comprehensive fringe programme will keep Cinte Techtextil fairgoers up to date with industry news, with standout events including the 7th China International Nonwovens Conference. Focusing on the global nonwovens industry, topic highlights include the latest innovations in China’s nonwovens industry, an insight into the North American nonwovens market, future trends in the global hygiene product market, and more. The conference will also discuss innovations and developments in filter materials and the wipe industry.

The first day of the fringe programme will see a panel discussion in hall N1, moderated by the Taiwan Technical Textiles Association (TTTA), with confirmed panellists including DuPont, IBENA Textilwerke and SGS-CSTC Standards Technical Services. The panel will focus on current trends, developments and standards in the protective textile industry.

Other fringe programme events will include seminars and product presentations led by industry leaders on the latest global technologies and market trends, and an Innovation Showcase Area in a variety of application categories. 

This September’s Cinte Techtextil China will once again provide a strong barometer of the state of the global technical textiles industry, and in particular which sectors in Asia as a whole, and China specifically, are performing well. Two of these for certain are Buildtech and Mobiltech, with a number of leading global and Chinese brands exhibiting to eager buyers from these sectors.

Cinte Techtextil China is Asia’s leading biennial fair for the technical textiles and nonwovens sector, and will feature an expected 500-plus total exhibitors from around 20 countries & regions from 4 – 6 September. The fair offers products and technologies for 12 application areas* which cover the entire industry.

Buildtech benefits from Belt & Road and other infrastructure investment

With a huge boom in national and regional infrastructure projects, the market for Buildtech products, especially geotextiles and construction textiles, is rapidly expanding. In particular, the government’s global Belt & Road project, as well as continued investment at home in highways, high-speed rail and more, is fuelling this expansion. According to CNITA, in 2017 China started 35 new railway projects, with additional private capital investment in this sector totalling some USD 53 billion that year. The same investment in highway construction increased 17.7%, while water conservation project investment by private firms reached a new record of USD 105 billion.

With this potential in the Asian market, it’s no surprise a number of new exhibitors will feature in the Buildtech sector at the fair, including FPC Technical Textile from Saudi Arabia, Kobe-cz from the Czech Republic, as well as Lenzing Plastics, while Johns Manville are one of the returning exhibitors this year.

• FPC Technical Textile (Saudi Arabia) produce high-end specialty fabrics including PVC coated fabrics and fibre glass PTFE fabrics, and will focus on the latter at the fair.
• Kobe-cz (Czech Republic) will showcase their nonwoven fabrics, mainly from glass fibre with temperature resistance up to 800°C.
• Exhibiting for the first time at the fair with their Plastics division, Lenzing (Austria) will feature their technical laminates for building industries, roofing membranes, vapour barriers, isolation facings and barrier packaging, as well as PROFILEN® PTFE yarns, films and fibres at Cinte Techtextil.
• Johns Manville’s (US) products on offer include polyester spunbond, PP & PBT meltblown, glass fibre nonwovens, micro glass fibre nonwovens, hybrid nonwovens, glass fibre needle mat and glass microfibers.

Mobiltech benefits from huge increases in automobile production in China

With new textile innovations and application possibilities spreading throughout the automobile industry, coupled with the fact China is the world’s largest auto producer, Cinte Techtextil is the place to see the latest products and technologies for this sector this September. Automobile production in China reached 29 million units in 2017, an increase of 3% year-on-year. Staggeringly, new-energy vehicle production grew by 53% last year, while SUVs and commercial vehicles increased 13.81% and 13.95% respectively.

With such strong growth in China, a number of leading international Mobiltech producers, as well as top domestic suppliers, will be at Cinte Techtextil this year, including:

• Abifor (Switzerland): their focus at the fair is on products designed for automotive, construction and other technical applications, in particular their specialty hot-melt powders. The company has its own production unit in Shanghai, and reports that an increasing number of domestic customers are starting to focus on more sophisticated products.
• SKS Group (Sweden): will showcase high performance single end yarn for automotive and industrial hoses, and single end cord for automotive and industrial belts.
• Swisstulle (Switzerland): will have a range of products on offer for automotive, rail and aviation uses, including sunshade materials, nets, tube reinforcements and new possibilities for luggage compartment covers.
• Windel Textile Far East (Germany): with production undertaken in China, this German firm offers textile greige, half-done and finished materials. They offer nonwoven, knitted and woven fabrics (substrates), and glass fibre solutions. At the fair, they will showcase substrates for adhesive tapes / wire harnessing tapes, and Maliwatt- and coagulated microfibre fleece for covering vehicle interiors.
• Protechnic (France): they will feature hot melt thermoadhesive nets, webs and films, as well as laminating process in automotive and other industrial applications at Cinte 2018.
• Kuangda Technology Group (China): having supplied products for global brands such as Volkswagen and Audi, this Chinese supplier will offer automotive interiors, including interior fabrics, seat covers and cushions at the fair.
• Shanghai Shenda (ShanghaiTex Group) (China): specialising in automotive interior textiles, they manufacture a full range of products including grey car carpet, moulding car carpet, head liners (warp-knitting and nonwoven), seat belt, seat fabrics and more, and have supplied the likes of Mercedes-Benz, BMW, Volkswagen and GM.

Cinte Techtextil China is organised by Messe Frankfurt (HK) Ltd; the Sub-Council of Textile Industry, CCPIT; and the China Nonwovens & Industrial Textiles Association (CNITA). To find out more about the fair, please visit: www.techtextilchina.com.

Asia’s largest biennial event for the entire technical textiles and nonwovens sector will feature some of the industry’s biggest overseas machinery brands. Held on the earlier date of 4 – 6 September this year, the fair will feature an expected 500-plus total exhibitors from around 20 countries & regions.

As the world’s largest producer of technical textiles and nonwovens, China’s demand for production machinery is insatiable. As such, this September’s Cinte Techtextil China has attracted some of the world’s leading machinery brands, particularly in the nonwovens and sewing machinery sectors, ensuring a wide range of sourcing options for both domestic and international buyers.

Overseas producers respond to strong Chinese demand
As the Chinese domestic and export markets’ demand for quality technical textiles and nonwovens products continues to increase, overseas machinery brands continue to enter the country, using Cinte Techtextil China as their starting-out platform. ANDRITZ Nonwoven is just one of those who see the growing potential. “Chinese nonwovens manufacturers are increasingly requiring higher capacities and top-class quality for their nonwovens products for local and export markets,” Mr Laurent Jallat explained. “China is the biggest market in terms of installed capacity, and shows quite promising potential for the future. In the past years, we’ve seen rapid growth in products such as disposable face masks.” ANDRITZ responds to this demand with their neXline spunlace eXcelle line which features state-of-the-art TT card web forming and JetlaceEssentiel hydro entanglement units for high capacity and speed.

The DiloGroup also report an increase in demand for their products in China. “China is one of our biggest markets,” explains Mr Dominik Foshag. “We have procured huge orders from China, as Chinese customers are considering German technology more frequently nowadays. The visitor quality of Cinte Techtextil has been very good in this past, and we think this year’s fair will be also successful as we know many of our customers are going to visit.”

Oerlikon will introduce its spunbond technology to the Chinese market this year, and is expecting to conclude initial contracts at the fair due to increased demand for overseas products. “The Chinese market for nonwovens products is by far the largest and fastest growing national market. Chinese manufacturers are no longer satisfied with lower product quality, but want to exceed Western quality levels, for example. The products must now meet stricter customer requirements and legal standards, some of which are significantly higher than other international standards,” Ms Lena Kachelmaier said.

Truetzschler Nonwovens has also noticed this trend. Ms Jutta Stehr commented: “In the last two or three years, China became one of the pacemakers in the field of nonwovens used in beauty, skin care and hygiene applications. Asian markets have set new standards concerning quality in nonwovens. For instance, making disposable wipes from cotton fibres is a trend originating in Asia. The luxurious feeling of cotton combined with the requirement for eco-friendly products will further drive demand in China and elsewhere. Accordingly, Truetzschler Nonwovens anticipates more inquiries at Cinte Techtextil for its proven carding and spunlacing solutions for cotton nonwovens.”

Weaving machine supplier Itema has also noticed strong demand in China for products made in Italy. “Generally speaking, and especially for technical fabrics, imported machinery is highly evaluated and appreciated by Chinese customers. In recent years, Itema experienced significant growth in the sale of its Made-in-Italy weaving machines in China, and in other APAC countries. Imported machines are synonymous with quality and reliability, and we believe this positive trend will be constant in the future,” Mr Matteo De Micheli outlined.

Weaving machinery exhibitor highlights

• ANDRITZ Nonwoven: their specialty is technologies for drylaid, wetlaid, spunbond, spunlace, needlepunch and textile calendering. At Cinte Techtextil, they will highlight their aXcess product portfolio, which has been especially designed for medium-capacity production. ANDRITZ has developed this range to fit the demands of producers with medium-capacity requirements, particularly in emerging markets. It includes lines and individual machines for needlepunch, spunlace, wetlaid and calendering processes.
• Autefa Solutions: visitors to their booth will experience the company’s expertise as a full line supplier for carded- crosslapped needlepunch lines, aerodynamic web forming technology, spunlace and thermobonding lines. Their nonwovens lines meet customers’ requirements for quality web formation, bonding, active weight regulation and minimal maintenance.
• DILO Systems: a leader in the field of staple fibre nonwoven production lines, DiloGroup will present their latest developments at the fair, including staple fibre production lines, card feeding and cards and crosslappers & needlelooms.
• Oerlikon: they will showcase spunbond solution lines for the production of polypropylene geotextiles. According to the company, spunbond geotextile applications are on the rise as the market is increasingly demanding more efficient processes and products, which means the product requirements are often the same or greater, but with a lower raw material input. Spunbonds are progressively replacing classical carded nonwovens due to their technical and commercial benefits.
• Truetzschler Nonwovens: concentrating on solutions for producing a broad range of hygiene nonwovens including wipes at the fair, they will focus on thermobonding & spunlacing processes and the respective machinery, from fibre preparation down to winding.

Sewing machinery exhibitor highlights

• Itema: making their debut at Cinte Techtextil, they are a leading supplier of weaving machines for technical fabrics production. According to the company, they are the only weaving machine producer to offer technical textile manufacturers the top three technologies for weft insertion: Rapier, Projectile and Airjet.
• Picanol: they use their leading position as producers of weaving machines for other textile products to expand into machines for woven technical textiles by investing heavily in state-of-the-art technology, as well through the modular design of their machine platforms which allow them to serve different industry sectors effectively.
• Lindauer Dornier: featuring in the German Pavilion this edition, they offer a number of weaving machine varieties including rapier, air-jet, open reed weave (ORW) and more. Their rapier weaving machines have set the technological standard in the high quality wool textiles market for decades, and this quality will be on display at their booth with the DORNIER P1 rapier weaving machine.

Domestic brands to watch out for

In addition to these leading overseas brands, a strong line-up of Chinese machinery producers will also feature at the fair, including Changshu Weicheng Non-Woven Equipment and Shijiazhuang Textile Machinery.

OutDoor2018: Schoeller’s coldblack® technology has been specifically optimized for use on knitted and woven fabrics so brands can now expand their product application uses. Under the blazing sun, textiles with coldblack® heat up less and stay cool to the touch. Südwolle Group, a leading manufacturer of high quality yarns, has also recognized the ideal combination of merino and coldblack®. With this, the wear comfort of wool apparel can be tangibly improved.

Wool is well known for its various property benefits, including insulation, natural antibacterial protection, odor control, light weight and nearly wrinkle free composition. Not only in the winter time, but also in summer particularly merino wool, a special high-quality type of wool, regulates moisture balance and thus the body temperature. The fibers can absorb a great deal of moisture or sweat and transport it away from the body. Warm ambient air quickly dries the material and causes a cooling evaporation, which makes it very comfortable to wear merino apparel in the summer time.

coldblack® technology from Schoeller supports the natural properties of wool because it reliably reduces heat build-up when exposed to the sun. Together with the help of Südwolle Group, the finish has been optimized specifically for the use in merino apparel. The yarn manufacturer chooses coldblack® for a variety of uses, especially for knitting and weaving yarns for sports and outdoor apparel and develops such products individually according to its customers’ requirements.

Stéphane Thouvay, Managing Director Product Management & Innovation at Südwolle Group, summarizes the use of the technology as follows: “coldblack® is part of our product range for the summer time, which we will be presenting at OutDoor show in Friedrichshafen. The technology reduces not only heat build-up, but also enhances the natural UV protection of wool without affecting the look and feel of the fabric. Therefore coldblack® perfectly fits into our yarn selection for sports and outdoor apparel, for example in our collection ʻYarn in Motion’. For end consumers garments made of coldblack® yarns can optionally be labeled with hangtags.”

When used in high-quality woolen fabrics, coldblack® has already proven its performance and is being used by renowned brands in various collections of men’s suits. Since 2008, the technology has been licensed by more than 200 brands, in sports particularly in the field of cycling, triathlon and golf. All components of the finish are bluesign® approved.