From the Sector

Order Intake Continued to Recover in the Fourth Quarter of 2020:

• Order intake increased to CHF 215.1 million in the fourth quarter of 2020 and reached a total of CHF 640.2 million in the 2020 financial year
• As expected, sales of CHF 573.0 million in the 2020 financial year were significantly down on the previous year
• EBIT margin of around -15% and net profit of around -16% of sales expected
• First half of 2021 still heavily impacted by the COVID-19 pandemic
• Change to the Group Executive Committee

Rieter posted a globally and broadly supported order intake of CHF 215.1 million in the fourth quarter of 2020. Thus, the recovery that began in the third quarter of 2020 after the slump in demand in the second quarter continued (order intake second quarter: CHF 45.7 million, third quarter: CHF 174.4 million). Overall, Rieter’s annual order intake for the 2020 financial year totaled CHF 640.2 million, which corresponds to a decrease of 31% compared to the previous year.

At the end of 2020, the company had an order backlog of about CHF 560 million (December 31, 2019: about CHF 500 million).

As expected, as a consequence of the economic effects of the COVID-19 pandemic, the Rieter Group closed the 2020 financial year with considerably lower sales than in the previous year. According to the first, as yet unaudited figures, total sales of CHF 573.0 million were achieved, which corresponds to a decrease of 25% compared to the previous year (2019: CHF 760.0 million).

Order Intake by Business Group
All three business groups were affected by the slump in demand in the second quarter of 2020 due to the COVID-19 pandemic. Despite the recovery in order intake in the third and fourth quarters of 2020, the weak second quarter was only partially offset.

The Business Group Machines & Systems was particularly hard hit by the effects of the pandemic, with a year-on-year decline of 35%. The Business Groups Components and After Sales each recorded a 24% reduction in order intake.*

Sales by Business Group
The exceptional market situation in 2020 gave rise to a significant decline in sales in all three business groups. Accordingly, reluctance to invest and deferred deliveries by customers caused sales in the Business Group Machines & Systems to decline by 24% compared to the previous year.

Due to COVID-19, a large number of spinning mills stopped production worldwide. This led to low demand for spare parts and wear parts, especially in the second and third quarters of 2020. Accordingly, compared to the previous year, sales in the Business Groups Components and After Sales fell by 24% and 27% respectively in the 2020 financial year.*

Sales by Region
With the exception of Turkey, all regions were affected by the low demand as a consequence of the COVID-19 pandemic.*

EBIT Margin and Net Profit
In the 2020 financial year, Rieter anticipates an EBIT margin of around -15% (2019: 11.2%) and net profit of around -16% of sales (2019: 6.9%). As of December 31, 2020, Rieter had liquid funds of exceeding CHF 280 million and unused credit lines in the mid three-digit million range.

First Half of 2021 Still Heavily Impacted by the COVID-19 Pandemic
Thanks to the improved capacity utilization, Rieter is planning short-time working in only a few areas in the first half of 2021. Nevertheless, Rieter expects sales in the first half of 2021 to be below the break-even point.*

Change to the Group Executive Committee
With effect from March 1, 2021, the Board of Directors of Rieter Holding Ltd. has appointed Roger Albrecht as Head of the Business Group Machines & Systems and a member of the Group Executive Committee.*

Annual General Meeting April 15, 2021
The 2021 Annual General Meeting of Rieter Holding Ltd. will take place in Winterthur on April 15, 2021.*

*See attached document for more information.

The Spring Edition of Intertextile Shanghai Home Textiles will return to the National Exhibition and Convention Center (Shanghai) from 10 – 12 March 2021, together with four other textile events including Intertextile Shanghai Apparel Fabrics – Spring Edition, Yarn Expo Spring, CHIC and PH Value. The fairs will offer an all-round business platform and a host of exciting synergy effects for the sector.

High-quality finished products to be offered
In March 2021, the Spring Edition will showcase a selection of home textile products including bedding & towelling, rugs, table & kitchen linen, home textile technologies, textile design and many more. Additionally, the fair will be held concurrently with Intertextile Shanghai Apparel Fabrics – Spring Edition, Yarn Expo Spring, CHIC and PH Value, offering a comprehensive sourcing platform for the sector.

Lenzing views Intertextile as an ideal platform to present their sustainable home products
The Lenzing Group, a leading producer of man-made cellulose fibres, is amongst the major industry players who have already confirmed their participation in the upcoming fair. Ms Lesley Wu, Home Textile Business Development at Lenzing Fibers (Shanghai), talked about new market trends in the post-pandemic era and the reasons they decided to join the Spring Edition of Intertextile Shanghai Home Textiles:

“Even though the home textile industry has, to some extent, been negatively impacted by the COVID-19 outbreak, there are both opportunities and challenges for the sector. Without a doubt, environmental protection and sustainable development are the hottest topics in today’s society. Consumers are paying more attention to healthy lifestyles and looking to make a shift to green consumption as a result of the pandemic. More and more consumers are opting for functional and sustainable raw materials. Environmentally sustainable fibres are therefore gaining popularity.”

“Right now, we expect the home textile industry will continue its steady recovery. Home textile companies may look for opportunities in product and marketing innovations, such as developing functional and sustainable home textile products and exploring various O2O business model options,” Ms Wu added.

Lastly, Ms Wu shared why they chose to participate in Intertextile: “We decided to exhibit at Intertextile Shanghai Home Textiles because it is an influential trade fair for the industry. As the Lenzing Group has been expanding in the home textile market, we want to use this platform to showcase the applications for TENCEL™ branded fibres in home textiles, and to further promote sustainability through our TENCEL™ Home cellulosic fibres.”

To find out more about this fair, please visit: www.intertextilehome.com

In pandemic year 2020 circular knitting machine manufacturer Mayer & Cie. (MCT) has further improved its leading position in Turkey. So the country continues to be one of the company’s strongest and most consistent sales markets. Even in difficult years, the manufacturer and its longstanding Turkish representative Mayer Mümessillik have achieved positive results. The reasons for this year’s success, as Mayer & Cie. sees it, are the transfer of production to locations close to Europe, Turkey’s state-of-theart machinery and the increase in demand for comfortable clothing that is suitable as home office wear.

Turkish market is a growth market despite corona setback
“Compared to 2019, we anticipate a growth in the Turkish market even though the corona situation was a serious setback in the second quarter of 2020,” says Stefan Bühler, Mayer & Cie.’s regional sales manager for Turkey.

Mayer & Cie. got off to a strong start on the Bosporus in the first quarter of 2020 with additional positive effects until mid-March. This was due to a desire for production locations close to Europe. In the second quarter, during the lockdown, demand largely ground to a halt. Government measures helped to cushion the downturn. Says Ahmet M. Öğretmen, general manager of MCT’s Turkish sales partner Mayer Mümessillik: “In the second quarter, GDP was down by about 10 percent, so we got off lightly.”

Since July 2020, orders for Mayer & Cie. circular knitting machines have bounced back again. Ahmet M. Öğretmen sees an interplay of reasons for this recovery. The main reason, he says, is the low exchange rate of the Turkish lira, which has boosted exports of ready-made textiles. The Turkish daily Hürriyet reports, with reference to the Turkish state news agency, 11 percent year-on-year growth in August 2020. The most important export markets, the newspaper says, are Germany, the UK and Spain. Between them, they account for around half of exports totalling € 1.27 billion.* “This demand must be fulfilled,” Öğretmen says. “That leads to investment in machinery by manufacturers.”

Relanit is synonymous with single jersey
The machines of choice for Turkish knitwear manufacturers are regularly Mayer & Cie. machines. The long-established German firm’s share of the Turkish market is substantially higher than in other markets. The manufacturer’s position is particularly strong in the market for plain single jersey fabrics, with the Relanit 3.2 HS being the machine of choice. It achieves an extraordinarily high level of productivity, especially in processing elastomer yarns. It also handles a wide range of yarns reliably.

“Interlock is Mayer & Cie.”
Mayer & Cie. is one of the leader in the second major circular knitting discipline, rib and interlock fabrics. The machines used for double jersey fabrics are the OV 3.2 QCe, the D4 2.2 II and the D4 3.2 II. The OV 3.2 QCe knits interlock, 8-lock structures, spacers and fine gauge with 3.2 systems. The D4 2.2 II is another stalwart for rib, 8-lock and interlock. The 8-lock D4 3.2 II is the machine of choice for firms that want to manufacture structures such as Piqué, Punto di Roma or Thermal in addition to interlock.

The MBF 3.2 is another top seller in Turkey. A three-thread fleece machine, it knits fabrics for sportsand leisurewear such as hoodies and is very much in keeping with the trend in home office year 2020. “Comfortable clothing is circular knitted,” says Ahmet M. Öğretmen, “and we benefit from that of course.”

One of the world’s most state-of-the-art machine parks are in Turkey
Another advantage is the modernity of the Turkish machine park, which is doubly attractive in view of Turkey’s weak currency. Says Mayer Mümessillik general manager Öğretmen: “In the past 10 to 20 years there has been very heavy investment in high-quality machines. As a consequence we have the world’s youngest and most up-to-date production facilities.” Combined with geographical proximity to the main export markets in Europe that should prove a growth driver in the years ahead – and keep demand for Mayer & Cie. machines brisk and high.

*More informationen here.

• On October, 20th, 2020, the State Prize for Innovation was awarded to the Lenzing Group for their LENZING™ Web Technology.
• Lenzing thus received the highest award for particularly innovative achievements in Austria.

Lenzing – On Tuesday, October 20, 2020, the Lenzing Group was awarded the coveted “State Prize for Innovation”. Lenzing emerged as the winner with its project LENZING™ Web Technology and thus received the highest recognition for particularly innovative achievements in Austria. The novel process combines fiber and nonwovens production in only one step, setting new standards in terms of efficiency, circularity and ecological sustainability. Margarete Schramböck, Federal Minister for Digital and Economic Affairs, presented the award to Gert Kroner, Vice President Global Research & Development.

“This award is a great recognition of our work. Our goal is to grow continuously with sustainable innovations and to look beyond our fibers, to the needs of our customers and partners and to the needs of consumers worldwide. With the LENZING™ Web Technology we have created an exciting and promising solution for eco-friendly products in line with our corporate strategy sCore TEN and support consumers in their daily needs in a sustainable way”, says Stefan Doboczky, Chief Executive Officer of the Lenzing Group.

Biodegradable nonwovens for a clean environment

The pollution of the environment by plastics is one of the most urgent problems of our time. Every day, millions of hygiene products and wipes around the globe end up in garbage and sewage. Most of them consist of up to 80 percent polyester or other fossil, non-biodegradable materials and therefore pollute the environment. With the LENZING™ Web Technology, Lenzing has developed a patented technology to counter this problem: Sustainable and eco-friendly nonwovens are produced from the renewable raw material wood. These are not only plastic-free, they also score points for their particularly high environmental friendliness. “Thanks to a unique self-bonding mechanism, in which the filaments bond with each other during the spinning process, binders, which are found in many nonwovens, are no longer needed. As a result, the nonwovens produced with LENZING™ Web Technology are 100 percent biodegradable and do not pollute either humans or the environment”, says Gert Kroner, Vice President Global Research & Development of the Lenzing Group.

The Austrian State Prize for Innovation is awarded annually by the Federal Ministry for Digital and Economic Affairs to the most innovative Austrian company. In 2020, the competition took place for the 40th time.

• World Cotton Day on 7 October Highlights the Importance of Cotton for Development Policy

Bremen - Stemming from a 2019 initiative of the African Cotton-4 countries Benin, Burkina Faso, Chad and Mali, World Cotton Day will take place this year on 7 October. The event is organised by the Geneva-based World Trade Organisation (WTO) and is supported by the Food and Agriculture Organisation of the United Nations (FAO), the United Nations Conference on Trade and Development (UNCTAD), the International Trade Centre (ITC) and the International Cotton Secretariat (ICAC). The Bremen Cotton Exchange is also involved.

“Cotton is often underestimated because it is so natural. Behind it are millions of people, for example many farmers, field workers, employees in ginning factories, logistics providers and traders. We want to honour their achievements,” said the President of the Bremen Cotton Exchange, Stephanie Silber.

According to the WTO, the aim of World Cotton Day is to highlight the global economic importance of cotton and to raise awareness of the raw material by recognising the work of everyone involved in its cultivation, processing and trade. At the same time, within the framework of international cooperation, it is hoped that supporters and investors can be found to aid with technological and economic progress within the cotton value chain.

This time, the entire world cotton community will be involved in World Cotton Day on Wednesday, 7 October 2020. A wide variety of campaigns and events are taking place everywhere to draw attention to the importance of cotton and its possible uses.

Cotton is one of the most relevant agricultural raw materials in the world. Around 26 million tonnes of it are harvested annually. Approximately 150 million people in almost 80 countries around the world live from the cultivation of the natural fibre. A large number of these live in developing countries, where cotton cultivation is of particular importance as a cash crop.

Cotton is known as an agricultural product that is turned into a textile. The raw material is indispensable in fashion and clothing – and has been for thousands of years. But the use of cotton now goes far beyond textiles. For example, cosmetic products such as hand creams and hair shampoo are made from the oil of cotton seeds. The raw material is also used in the manufacture of banknotes, furniture and technical textiles, as well as in medical technology.

Against the background of the current discussion on sustainability and sustainable consumption, the role of natural fibres is becoming even more important. Cotton is biodegradable and a renewable resource. It can be grown again and again in agriculture through cultivation in crop rotation. This secures incomes and enables efficient value creation within the global production and processing chain.

The Bremen Cotton Exchange will actively support World Cotton Day with cross-media coverage. In addition, in time for World Cotton Day, three thematically different, emotionally appealing short films about cotton will be launched. They are aimed at consumers as customers of the textile and clothing trade and provide information about the benefits and properties of cotton and answer questions about its sustainability. In keeping with the times, they will be published via virtual media.

• Energy efficiency will be the topic of VDMA’s next edition of Textile Machinery Webtalks on 27 August 2020 (2 pm - 4 pm CEST).  

Efficient energy management is of increasing importance in textile dyeing and finishing. Innovative machine designs with minimal water and energy consumption as well as the recovery and use of the heat energy produced in the processes represent valuable potential savings for any modern company.

The presenters at a glance:

• Ludger Sommer, Thies, will show how to manage heat energy in wetprocessing.
• Benjamin Schnabel, Brückner Textilmaschinen is going to demonstrate how to make one of the most energy consuming processes in textile manufacturing more sustainable, eco-friendly and cost effective.
• Fabian Buckenmayer, PLEVA Sensors and Controls will inform about the specific opportunities for an energy-efficient textile production via measuring and controlling process parameters.  

After the presentations, the experts will be available to answer the participants' questions. The webtalk series is very well received by the textile industry. During the first three webtalks, VDMA welcomed almost 900 registered participants from more than 50 countries. Registration is still possible.

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

A new standard in pure white, 100% clean and fault-free textile substrates has been demanded by this market in recent years due to the rapid growth in digitally-printed banners and billboards – often referred to as ‘soft signage’.

The substrates of choice for digital printing are 100% polyester warp knits which are resilient and allow excellent take-up of inks, and vibrant colours and clear and precise images to be achieved with digital printing techniques. The knitted construction also has the advantage of elasticity, which is a plus in terms of flexibility for installers.

Critically, the warp knitted fabrics have extremely smooth surfaces which is becoming increasingly important due to the general move away from PVC coatings which were the standard in the past.

It was to finish these fabrics for Georg and Otto Friedrich GmbH as well as providing such services for many other customers, that the GtA plant in Neresheim, Baden-Württemberg, was established in 2015.

The purpose-built plant on a greenfield site was initially equipped with a fully-automated, 72 metre long Monforts installation comprising a washing machine integrated with a 3.6 metre wide, seven-chamber Montex stenter. The line quickly went from single to double shift production and then to 24/7 operation  to meet demand.

Expanded widths

Building on the success of this installation, GtA has now installed two more Montex stenter lines – both in expanded working widths of 5.6 metres and purpose-built at Montex GmbH in Austria.

A six-chamber Montex unit is combined with a washing machine to guarantee the purity of the substrates, while a five-chamber line is integrated with a wide-width coating machine. This new coating capability at GtA has led to a number of new additions to the Georg and Otto Friedrich DecoTex range for digital printing, including wide width fabrics with flame retardant, antimicrobial and non-slip finishes.

The new Montex stenter lines benefit from all of the latest innovations from Monforts, including the Smart Sensor system for the optimised maintenance planning of key mechanical wear components on the stenters. A comprehensive overview of the condition of all parts at any time is now available for operators within the highly intuitive Qualitex visualization software.

With Qualitex, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

Environmental commitment

GtA is run by a seasoned team of textile professionals led by Managing Director Andreas Niess.

“We have received excellent service from Monforts from the outset and we were happy to place the order for these two new lines as part of our ongoing cooperation,” he says. “With all of the latest Monforts advances in technology we are fully in control of all production and quality parameters with these lines, as part of our significant commitment to innovative environmental technology.”

The GtA plant, which operates in near-cleanroom conditions, has also been equipped with proprietary technology to fully exploit the Monforts air-to-air heat recovery systems that are now standard with Montex stenters.

“Around 30 per cent of our investment volume at the site goes to energy-saving measures and we are sure that this commitment is worthwhile,” Mr Niess says. “As an example, our integrated heat recovery system fully exploits the waste heat from the process exhaust air and the burner exhaust gases of the Monforts stenters, allowing us to achieve an exhaust air temperature of  between 30 to 34°C, compared to what would conventionally be between 140 to 160°C. Another focus has been on exhaust air purification technology and here too, the latest technology has been installed with integrated heat recovery elements.”

This, he adds, saves 52% of the energy that would normally be used – equating to 5,800,000 KwH per year. The necessary audits for energy-efficient companies are also carried out annually.

In addition, GtA has purpose-designed the automatic chemical mixing and dosing systems that feed the padders for the key treatments that are carried out on the fabrics through the stenters.

The company is going further, however, in its pursuit of clean production and raw materials.

"We want to be an asset and not a burden on our immediate environment and therefore do not use any additives containing solvents," Mr Niess says. “We were the first to use fully halogen-free flame retardant chemistry, and we use bio-based, finely ground alumina products for the washing process instead of surfactants. PES polyester yarns made from recycled material are also increasingly used and the latest additions to our raw materials portfolio, the RC-Ocean products, are made from recycled sea plastic.

“We are now planning a combined heat and power plant for the production of electrical energy and heat and we will also build a photovoltaic system that converts solar radiation into electrical energy. GtA wants to be the first textile finishing company to be CO2-neutral in the manufacture of all of its products by 2025. The complete heat supply and heating for the 13,000 square metre production hall, as well as the office building and the hot water supply for the domestic water, is already energy-neutral. We are convinced that this commitment will pay off in the long term and our positive business development proves that sustainability and business profitability are perfectly compatible.”

In addition to the products for Georg and Otto Friedrich GmbH, GtA  offers its manufacturing capacities for other customers as a contract service.

All products are manufactured in accordance with Öko-Tex Standard 100, product class 1 and the company is also involved in the research and development of new sustainable manufacturing processes, in cooperation with many regional universities and funding project partners.

• Schleswig-Holstein Minister President visits Neumünster, Germany

Since the outbreak of the coronavirus pandemic, the worldwide demand for protective masks and apparel has resulted in a record number of new orders in the high double-digit millions of euros at the Oerlikon Nonwoven business unit of the Swiss Oerlikon Group. From the manufacturing site in Neumünster, Germany, the high-tech meltblown systems – with their patented ecuTE+ nonwovens electro-charging technology – are meanwhile be exported all over the world. For the very first time, a contract has now been signed with a business in Australia. Today, Schleswig-Holstein’s Minister President Daniel Günther was won over on site by the technology of a ‘global player’. Rainer Straub, Head of Oerlikon Nonwoven, was thrilled, stating: “The machines and systems for manufacturing manmade fiber and nonwovens solutions from Neumünster enjoy an outstanding reputation throughout the world. It is especially in this crisis that the technology from Schleswig-Holstein has proven itself to be absolutely world-class.”

In addition to a tour of the meltblown system and its assembly and production facilities, the visit by Minister President Daniel Günther had one purpose above all: the dialog between politicians and business. Rainer Straub, Head of Oerlikon Nonwoven, and Matthias Pilz, Head of Oerlikon Neumag, jointly expressed their thanks for the support that Oerlikon has repeatedly had the fortune to experience over the past months and years in Schleswig-Holstein and looked to the future full of hope. “As a result of our additional investment at the site here in Neumünster – be this in our new technology center that will be completed by the end of this year or in our new logistics center that is already operating – we, as one of the region’s largest employers, are continuing to move forward, supported by a State Government that is also focusing on both promoting industry and business and on advancing an efficient training and educational system, as innovation is only possible with outstanding engineers”, stated Matthias Pilz. And Rainer Straub directed his appeal specifically at the Minister President: “Treat education and training as a priority. Ultimately, they will secure the future of Schleswig-Holstein as a center of excellence and manufacturing!”

Five-million-euro digitalization program

Daniel Günther, the incumbent Minister President of Schleswig-Holstein since 2017, immediately responded, making reference to one of the Federal State’s current training initiatives: “The State Government is supporting higher education institutions and students in the present coronavirus crisis. With a five-million-euro digitalization program, we are investing on the long-term digitalization of our higher education institutions. With this, we are overall creating a future for young people, particularly also for those who could very well go on to invent the next generation of manmade fiber systems.” And the Minister President was just as impressed by the willingness and readiness with which Oerlikon has been providing high-level support since the beginning of the COVID-19 pandemic to master the present challenges as he was with the company’s meltblown technology itself. Rainer Straub explained: “When, at the beginning of the pandemic in February, demand for protective face masks increased rapidly, we at Oerlikon Nonwoven responded immediately. We ramped up all the available production capacities here in Neumünster in order to quickly manufacture nonwovens for producing face masks using our laboratory systems. As a result, we have been able to make a small, regional contribution to covering demand. In parallel, we have pulled out all the stops in order to systematically further expand our skills as machine and system builders so as to cater to the initially expected, and now also continuing, global demand for meltblown systems as quickly as possible.”

Leading meltblown technology

The Oerlikon Nonwoven meltblown technology – with which nonwovens for protective masks can also be manufactured, among other things – is recognized by the market as being the technically most efficient method for producing highly-separating filter media made from plastic fibers. The capacities for respiratory masks available in Europe to date are predominantly manufactured on Oerlikon Nonwoven systems. “Ever more manufacturers in the most diverse countries are hoping to become independent of imports. Therefore, what we are experiencing in Germany is also happening in both industrialized and emerging countries throughout the world”, commented Rainer Straub. In addition to China, Turkey, the United Kingdom, South Korea, Austria and numerous countries in both North and South America, Australia and not least Germany will for the first time also be among the countries to which Oerlikon Nonwoven will be delivering machines and equipment before the end of 2021.

Innovatives Kunstleder dank INSQIN® Technologie

Noch vor wenigen Jahren wurde mit dem Hinweis auf eine „Vollleder-Ausstattung“ auf die Hochwertigkeit eines Fahrzeuges hingewiesen und Echtleder war Ausdruck von Qualität und Extravaganz. Inzwischen hat sich dieses Bild jedoch gewandelt: Heutige Kunden achten bei ihren Kaufentscheidungen verstärkt auf nachhaltige Produkte mit möglichst geringem CO2¬-Fußabdruck. Weitere wichtige Produktmerkmale sind Qualität und Langlebigkeit. Sie spielen vor allem eine Rolle in viel genutzten Fahrzeugen der sich etablierenden Carsharing-Dienste. Anbieter dieser Services sind an einer langen Betriebszeit ihrer Flotte interessiert und legen zudem Wert auf einen geringen Pflegeaufwand ihrer Fahrzeuge.

Covestro entwickelte seine wässrige INSQIN® Technologie für eine nachhaltige, effiziente und dauerhafte Polyurethanbeschichtung von Textilien sowie die Herstellung von hochwertigem Kunstleder, auch und vor allem für den Autoinnenraum.

Umweltverträglich und langlebig

Herkömmliches Kunstleder wird oft unter Verwendung von organischen Lösemitteln produziert. Schon seit Jahren soll die Emission solcher volatile organic compounds, kurz VOCs, gesenkt werden. Covestro setzt deshalb auf eine wässrige Beschichtungstechnologie, die ohne Lösemittel auskommt. Durch die effiziente Technologie wird im Vergleich zum bisherigen lösemittelbasierten Koagulationsprozess nicht nur bis zu 95 Prozent Wasser und bis zu 50 Prozent Energie eingespart, der Fahrzeuginnenraum wird auch deutlich weniger durch VOC-Emissionen belastet.

Als Alternative zu Tierleder bieten INSQIN® Produkte gleich mehrere Vorteile: Durch ihr geringeres Gewicht erhöhen sie die Effizienz eines Fahrzeuges und senken somit seinen Kraftstoff- oder Stromverbrauch. Durch moderne Herstellungsverfahren sind sie langlebig, nachhaltig und recycelbar.

Innovative Materialien für Premium-Ansprüche

In der Textilbeschichtung konnten sich INSQIN® Produkte bereits etablieren und in vielen Anwendungsbereichen überzeugen. Im Fahrzeuginnenraum bieten sie nun die Möglichkeit, Oberflächen völlig neu zu gestalten und zu nutzen. Davon profitieren Designer ebenso wie Fahrzeugnutzer, denn Farbe, Haptik und Lichtdurchlässigkeit von Oberflächen lassen sich individuell einstellen. Da selbst bei dunklen Farbtönen transluzente Effekte erzielt werden können, lassen sich Kontrollleuchten oder Taster einfach unter der Oberfläche anbringen – ein Blick oder Knopfdruck wird hier zum Erlebnis.

• New composite e-Mobility application
• Multi-year substantial contract

After prototypes for a Chinese automotive manufacturer, a major order from a North American automaker, and yet another order for a European sports car manufacturer, SGL Carbon has now been nominated by BMW Group to produce a cover component for battery enclosures in series. This substantial multi-year order will include the production of an innovative glass-fiber-based cover plate for the battery housing for usage in a future plug-in hybrid model of BMW Group.

Materials made of composites are suited for battery enclosures for different reasons: Besides their light weight, which enhances the electric vehicle’s range, fiber-reinforced plastics offer high stiffness. In addition, they meet high requirements for water and gas tightness and feature excellent fire protection properties. Composite materials can also help to achieve improved structural stiffness of the underbody, e.g. to protect against penetration, as well as an optimized thermal management. Carbon fibers are ideal for especially stressed structures or load-bearing elements, such as the underbody panels and side frames. For components subjected to less stress, such as battery box covers, glass fibers or a fiber mix may suffice.

In addition to the new application for the hybrid model battery enclosure, SGL Carbon will continue producing the usual components made of carbon-fiber-reinforced plastic for the BMW i3 and delivering materials for the Carbon Core body of the BMW 7 series, and has been nominated as the supplier for all carbon materials - fibers, textiles, stacks - for the BMW iNEXT, set to be launched in 2021.