From the Sector

• Commitment for a sustainable fashion industry

RadiciGroup participated in the third edition of PHYGITAL SUSTAINABILITY EXPO, which took place on 11 and 12 July in Rome. The event was focused on the ecological transition of fashion and design brands through technological innovation.

During the “narrated fashion show”, at the archaeological site of the Museo Dei Fori Imperiali, two sustainable garments by RadiciGroup were shown: the first completely recyclable ski suit made with recycled nylon and the Yamamay swimsuit made with polyester yarn obtained from recycling of plastic bottles.

Yamamay chose the sustainable polyester yarn Repetable® by RadiciGroup, for its new green beachwear proposal, with the aim of combining beauty and sustainability. Repetable is an innovative polyester yarn obtained through a process of recycling plastic bottles. Compared to virgin polyester, Repetable allows lower CO₂ emissions (-45%), lower water consumption (-90%) and lower energy consumption (-60%), while guaranteeing high performance. The new line “Edit” by Yamamay, which includes the swimsuit made with Repetable, has already been on the market since the end of last May.

The participation of RadiciGroup in the PHYGITAL SUSTAINABILITY EXPO represents further confirmation of the Group commitment to creating a fashion industry that is increasingly respectful of the environment, thanks to the involvement of all the players in the supply chain, which are most sensitive to sustainability.

• Annual assembly of ACIMIT, the Association of Italian Textile Machinery Manufacturers

• Digitalization and Sustainability Key to Resiliency for Italian Textile Machinery Sector

The objective critical issues faced by Italy as a whole throughout the course of 2021, primarily dictated by a pandemic that upset any and all pre-existing equilibriums, have not slowed or halted the Italian textile machinery sector.

Indeed, data presented during the annual assembly of ACIMIT, the Association of Italian Textile Machinery Manufacturers, held on 1 July proved decidedly positive, showing that in 2021 the sector recovered significantly compared to 2020, to the point of returning to pre-Covid levels.

Specifically, Italian textile machinery production amounted to 2.388 billion euros (+35% over 2020 and + 5% over 2019), with total exports amounting to 2.031 billion euros (+37% over 2020 and +9% over 2019).

However, these results do not cancel the obstacles that companies are still facing. Looking to the near future, expectations are for a rather uncertain outlook, as underscored by ACIMIT President Alessandro Zucchi: “2022 remains a year replete with unknown factors, starting with the Russian-Ukrainian conflict, along with the persistence of the pandemic, which seriously risk delaying expected growth consolidation for businesses in the sector. Difficulties in finding raw materials and components negatively affect the completion and fulfilment of orders processed as far back as 2021. To boot, rising energy costs and inflationary trends affecting numerous commodities are depressing overall business confidence. So the outlook for the sector is not so good.”
As such, the two cornerstones through which ACIMIT aims to support the Italian textile machinery sector are digitilization and sustainability.

4.0: The textile machinery sector looks to the future
The road to digital transformation has already led numerous manufacturers to completely rethink their production processes, rendering them more efficient and l ess expensive. The digital world is moving ahead at a decisive rate in the textile machinery sector, where the buzzwords are increasingly, for instance, the Internet of Things connecting to a company’s ecosystem, machine learning algorithms applied to production, predictive maintenance, and the integrated cloud management of various production departments. It is no coincidence that ACIMIT has focused decisively on its Digital Ready project, through which Italian textile machinery that adopt a common set of data are certified, with the aim of facilitating integration with the operating systems of client companies (ERP, MES, CRM, etc.).

A green soul
Combining production efficiency and respect for the environment: a challenge ACIMIT has made its own and which it promotes among its members through the Sustainable Technologies project. Launched by the association as early as 2011, the project highlights the commitment of Italian textile machinery manufacturers in the area of sustainability. At the heart of the project is the Green Label, a form of certification specifically for Italian textile machinery which highlights its energy and environmental performance. An all-Italian seal of approval developed in collaboration with RINA, an international certification body.
The assembly held on 1 July provided an opportunity to take stock of the Sustainable Technologies project, more specifically, with the presentation of the Rina Consulting survey on the Green Label’s evolution and impact in recent years.

The results have confirmed the initiative’s extreme validity. The technological advances implemented by the association’s machinery producers participating in the project have effectively translated into benefits in terms of environmental impact (reduction of CO₂ equivalent emissions for machinery), as well as economic advantages for machinery users.

With reference to the year 2021, a total of 204,598 tons of CO₂ emissions avoided on an annual basis have been quantified, thanks to the implementation of improvements on machinery. This is a truly significant reduction which, for the sake of comparison, corresponds to the carbon dioxide emissions generated by 36,864 automobiles travelling an average of 35,000 km a year. In terms of energy savings, the use of green labeled textile machinery has provided excellent performances in allowing for a reduction of up to 84% in consumption.

A round table discussion on the Green Label’s primary purpose
The environmental and economic impact generated in production processes for Italian textile machinery through the use of Green Label technologies was the focus of the round table which concluded the ACIMIT assembly.

Moderated by Aurora Magni (professor of the Industrial Systems Sustainability course at the LIUC School of Engineering), the debate involved Gianluca Brenna (Lipomo Printing House administrator and Vice President of the Italian Fashion System for Welfare), Pietro Pin (Benetton Group consultant and President of UNI for the textile-clothing area), Giorgio Ravasio (Italy Country Manager for Vivienne Westwood), as well as ACIMIT President Alessandro Zucchi.

Called on to compare common factors in their experiences relating to environmental transition processes for their respective companies, the participants were unanimous: the future of Italian textile machinery can no longer ignore advanced technology developments capable of offering sustainable solutions with a low environmental impact while also reducing production costs. This philosophy has by now been consolidated, and has proven to lead directly to a circular economy outlook.

The upcoming ITMA 2023 exhibition
Lastly, a word on ITMA 2023, the most important international exhibition for textile machinery, to be held in Italy from 8 to 14 June 2023 at Fiera-Milano Rho. Marking the 19th edition of ITMA, this trade fair is an essential event for the entire industry worldwide, providing a global showcase for numerous innovative operational solutions on display. A marketplace that offers participants extraordinary business opportunities. The participation of Italian companies is managed by ACIMIT.

• Goal: to further reduce the textile value chain’s impact on people and planet      

As the textile industry continues to grapple with evolving regulations, increased consumer and stakeholder pressure to meet sustainability goals, and the lack of verified data, bluesign® has updated its service offerings to help brands, manufacturers and chemical companies to better understand and manage their value chains.

The new initiatives expand Bluesign’s core competencies of reducing impact across the supply chain, providing reliable, third-party verified data, mitigating the use of hazardous chemicals through input stream management and replacing substances with bluesign® APPROVED chemistry (a positive list of chemical products with less impact on people and planet). Bluesign’s high value services are available for all companies willing to reduce the impact of their value chain without compromising on quality.     

Bluesign is extending its System Partnership services and launching DATA SERVICES and IMPACT SERVICES for brands and manufacturers. These tiered service packages provide expanded capabilities that enable brands to actively monitor and manage their supply chain through Bluesign verified impact data, covering the critical measures of water consumption, energy consumption, greenhouse gas emissions, chemical consumption, and waste.

DATA SERVICES allow brands and manufacturers to access data from its unique supply chain and give a snapshot of their impact. Through the IMPACT SERVICE package, companies are provided this data plus a foundational assessment of its overall performance and detailed analysis of its suppliers.

The new IMPACT SERVICE enables manufacturers to present their achievements in impact reduction and their excellence in resource management.  The new tiered packages will allow companies to incrementally implement Bluesign’s services with the ultimate goal of attaining full SYSTEM PARTNERSHIP which includes company-specific action plans. At all service levels, a yearly impact report or dashboard is provided; access to this data enables accurate analysis for decision-making and reporting both internally and externally.

The electrolyser producer Enapter has set itself the goal of developing its entire production process to run without negative impacts on the environment. As an important step on this journey, it is building the Enapter Campus production facility, which will be powered entirely from renewable energy produced on-site and in the neighbouring Bioenergiepark. The site in in Saerbeck, North Rhine-Westphalia combines electrolyser production, an R&D building, administration and office space, as well as a cantine over 82,000 square metres. Now the company wants to investigate what other measures can be implemented to achieve its “Life Cycle Impact Zero” aspirations – together with researchers from Fraunhofer UMSICHT, the Wuppertal Institute and the Institute of Sustainable Nutrition (iSuN) of FH Münster.

With the Life Cycle Impact Zero project, started on April 15, 2022, the parties want to develop and apply an especially comprehensive and holistic approach to environmental assessment. This includes chemical manufacturing and electrolyser production, as well as matters like the use of energy and water resources, the generation of waste or the human factor in general. This is intended to cover all interactions between business and people. That includes, in particular, Enapter’s employees, but also people in upstream and downstream value chains, users of the technology or residents close to the production site. A concept for sustainable employee catering is also being developed.

The basis for all environmental assessment that will be carried out is ISO 14040. The recognised international standard divides the research into four phases: Aim and scope of the study, inventory analaysis, impact assessment, as well as interpretation. Sensitivity analyses and scenario techniques are also used as further methods.

On the basis of these analyses, the 18-month project should derive concrete measures to avoid negative environmental impacts completely, if possible, for example in production, employee mobility or in energy supply. Furthermore, it will examine whether these measures are transferable to Enapter’s other locations – such as in Italy. Following on from the project, the steps defined should be implemented by Enapter in the next phase. In the subsequent Phase 3, a renewed analysis is planned. This will determine if the technological innovations achieved by then in the production and use of Enapter’s electrolysers can enable additional ecological improvements.

The Life Cycle Impact Zero project is supported by the State of NRW.

Stahl, a proponent of responsible chemistry, is submitting a greenhouse gas (GHG) emissions reduction target that is aligned with the most recent guidance provided by the Science Based Targets initiative (SBTi). The new target marks a key milestone on the company’s journey toward carbon neutrality.

Stahl’s SBTi submission includes a specific commitment regarding the company’s Scope 3 upstream emissions, which Stahl aims to reduce by at least 25% over the next 10 years, compared with the base year (2021). This reduction would primarily be achieved by Stahl replacing its fossil-based raw materials with lower-carbon alternatives. The target is a major step towards the objective of limiting global warming temperature increase to 1.5°C above pre-industrial levels by 2050, as agreed at the 2015 Paris Climate Accords.
 
Stahl’s extended commitment builds on the company’s existing targets to reduce its emission for Scopes 1 and 2, which were set shortly after the Paris Agreement in 2015. Stahl has since reduced its Scope 1 and 2 (direct) GHG emissions by more than 30%, thanks to operational efficiency gains and by decarbonizing its energy supply.

Scope 3 GHG emissions cover all the additional indirect emissions that can occur in the value chain, including those associated with purchased raw materials, packaging, business travel, and transportation. Stahl’s Scope 3 emissions currently represent over 90% of its carbon footprint.

On June 13, EREMA Group and Borealis invited representatives of the international plastics and recycling trade press to Upper Austria for a sneak preview of the technological developments and lighthouse projects that the companies will present at K 2022, the plastics industry's international meeting place. The venue for the pre-K event was EREMA Group headquarters in Ansfelden.

EREMA Group K 2022 preview
In Düsseldorf, the subsidiaries of the EREMA Group - which are EREMA, PURE LOOP, UMAC, 3S, KEYCYCLE and PLASMAC - will present their technological innovations, services and support together at a Group trade fair stand for the first time. Seven new recycling systems and components will be presented that enable large-scale plants with a production capacity of up to 6 t/h while setting a milestone in recyclate quality and process stability. This is made possible by technological innovations in the plasticizing unit that have been specially developed for high throughputs with low specific energy consumption, the new EREMA 406 laser filter with a 50 percent larger screening area, and new digital assistance systems that will be launched at K 2022 and made available on the BluPort® customer platform. These include, for example, the PredictOn app, which helps to anticipate and eliminate imminent malfunctions based on continuous measurement and evaluation of machine data.

New series of machines for new target groups
For customers looking for rapidly available recycling systems for simple applications, EREMA Group subsidiary UMAC has an innovation in store for K 2022. The company, which has so far specialised in refurbishing and trading in previously owned equipment, is expanding its business area and in Düsseldorf will launch READYMAC, a standardised, prefabricated recycling solution that can be produced from stock, based on proven EREMA TVE technology.

Finally, in the inhouse recycling segment, PURE LOOP and PLASMAC will round off the wide range of machines offered by the group of companies with their product portfolio.

Live recycling and lighthouse projects at the Circonomic Center
In the outdoor area of the K show, EREMA will bring plastics recycling to life with live demonstrations in conjunction with cooperation partners. Different waste streams are processed for this purpose. The wide variety of high-quality applications for recyclate will be showcased in the "products made of recyclate" exhibition, ranging from technical components to consumer goods and food packaging.

Borealis – accelerating the transition towards a more circular future
Borealis is committed to using their expertise and global reach to advance the circular economy of plastics. At the joint Pre-K 2022 kick-off on June 13, Borealis provided a preview of their integrated way of circular thinking and featured topics and activities at the K Fair 2022 in October. The preview covered new technologies and innovations including new packaging and infrastructure applications of the Bornewables™ portfolio of circular polyolefin products, manufactured with renewable feedstocks. New applications for Design for Recyclability, Re-Use, chemical recycling and advanced mechanical recycling were also on display.

International technology group ANDRITZ has established a new inline Wetlace™ CP pilot line with an original design at its center of competence in Montbonnot, France. The line combines both spunlace and wetlaid technologies.

From now on, partners will be able to conduct trials and test all options available for wipes production – from carded staple fibers to pulp and various combinations thereof. The combination of both spunlace and wetlaid technologies offers to move forward to more sustainable options while maintaining a high level of product quality, in particular by achieving high CD strength and good linting properties.

Over the past few decades, ANDRITZ has continued to innovate with various nonwoven processes, like spunlace, WetlaceTM and Wetlace™ CP, with the aim of optimizing the use of raw materials and focusing on sustainability by reducing the synthetic fiber content. Facing the growing demand for bio-wipes in parallel with enforcement of the EU’s single-use plastics directive last year, ANDRITZ has decided to support its customers making their investment decisions.

The Montbonnot pilot line has been rebuilt to integrate the new headbox inside the spunlace line. Pulp can be fed in directly and entangled with carded staple fibers to produce unique nonwoven fabrics designed for end uses as bio-wipes.

• New yarns for the contract furnishing world, for industrial sewing threads and the challenge of biodegradable polyester

At the product level, big impulse has been given to the range of industrial sewing threads for various uses, with new references both in the polyester + polyester compositions as well as in cotton + polyester. The industrial threads, marketed as raw material, allow the company to consolidate its position on some strategic markets, such as in Germany.

As a result of the partnership with Trevira® for the spinning of the flame-retardant Trevira^®CS fibre, Filidea Technical Yarns reinforces its offer of non-dyed performant yarns aimed at the world of contract furnishings. The sector of hospitality, of furnishings for public and work spaces, fairs and areas for social-cultural gatherings will find a comprehensive answer to its demands in the Trevira^®CS-based yarns: with regard to fireproof standards, versatility, resistance to wear and tear, excellent colour rendering, and last but not least, the component of fibre sustainability, an essential value for the design of spaces for collective use.

Continuing in the development of sustainable production across the sector, the company has undertaken two important initiatives with other actors in the textile supply chain. Filidea participates in Trick, the European blockchain project – part of the European Horizon 2020 programme – involving 29 partners from six different nations to reinforce the circular economy thanks to the development of a digital platform which is complete, traceable and available to operators in the textile sector.

MagnoLab, the network of enterprises in the textile supply chain, and of which Filidea is one of the founding members, gives the impulse to constant R&D activities. MagnoLab was established in 2022 in order to develop tangible solutions for the sector, to create values and to collaborate with regard to current and future demands.

MagnoLab brings together textile companies which are active at various stages of and with complementary roles in the supply chain, and which work in synergy and share objectives, resourcefulness and long-sightedness, with the aim of developing innovation in a structured way. MagnoLab is also open to welcome new partners.

On the occasion of the Techtextil fair in Frankfurt, the Chairman of VDMA’s Walter Reiners-Stiftung Foundation, Peter D. Dornier, has awarded prizes to seven successful young engineers. For the first time, the Foundation awarded two Sustainability Awards. They are awarded to academic works in which, for example, solutions for resource-saving products and technologies are developed.

A Sustainability Prize in the category Project Work, endowed with 3.000 euros was awarded to Simon Hoebel, TU Dresden, for his thesis on recycled thermoplastic fibres for composite components.
Marina Michel, TU Dresden, received a Sustainability Award in the category Master, worth 3.500 euros. The topic of her master thesis was the functionalisation of yarns for the filtration of micro- and nanoplastics from water.

A Promotion Prize in the category Project Work, endowed with 4.000 euros, was awarded to a student group from RWTH Aachen. The teamwork of Luis Gleissner, Leopold Habersbrunner, Frederic Olbrich and Frederik Schicks was the construction of a test rig for tests on oil-adsorbing textiles.

Felix Zerbes, RWTH Aachen, was awarded a Promotion Prize of 3.500 euros in the category Master. He developed a technical solution for air jet weaving to improve the quality of woven fabric.

INDA, the Association of the Nonwoven Fabrics Industry, has announced the nomination process is now open for the annual RISE® Innovation Award. The prestigious award will be presented at the RISE® (Research, Innovation & Science for Engineered Fabrics) Conference – September 27-28, 2022, at North Carolina State University, Raleigh, NC.  RISE^® 2022 is a two-day conference presenting insightful research and science that propels product development.

Companies, academic institutions, research centers, and individuals are invited to nominate their advances in nonwovens and engineered materials at https://www.riseconf.net/award-submission.html until the July 15, 2022 deadline.

The RISE^® Innovation Award recognizes innovation within and on the periphery of the nonwovens industry that uses revolutionary science and engineering principles to solve current and future industry needs. Raw material advances, advances in process or manufacturing technologies including web forming and converting, new product or application development, and other areas that may extend or enhance the use of nonwovens will be considered for nominations.

Industry professionals involved with product development, material science, and disruptive enabling technologies for both consumer and industrial products are encouraged to nominate their product(s) for the RISE^® Innovation Award.

Nomination Process
Technical experts serving on the INDA Technical Advisory Board will review nominations and select three finalists who exemplify the use of cutting-edge science and engineering principles to advance the field of nonwovens. Finalists will present their innovations to technology scouts, scientists, researchers, and next level industry professionals at the RISE® Conference on Tuesday, Sept. 27, 2022.

Criteria and eligibility, nomination process timing, and prior award recipient information is available online: https://www.riseconf.net/award-submission.html