From the Sector

Reset
207 results
(c) ZAMG/Niedermoser
Scientists ascending to the research station in the Hohe Tauern National Park
01.02.2022

Plastic snowfall in the Alps - New Empa Study about nanoplastic in the environment

In a new study, Empa researcher Dominik Brunner, together with colleagues from Utrecht University and the Austrian Central Institute for Meteorology and Geophysics, is investigating how much plastic is trickling down on us from the atmosphere. According to the study, some nanoplastics travel over 2000 kilometers through the air. According to the figures from the measurements about 43 trillion miniature plastic particles land in Switzerland every year. Researchers still disagree on the exact number. But according to estimates from the study, it could be as much as 3,000 tonnes of nanoplastics that cover Switzerland every year, from the remote Alps to the urban lowlands. These estimates are very high compared to other studies, and more research is needed to verify these numbers

The study is uncharted scientific territory because the spread of nanoplastics through the air is still largely unexplored.

In a new study, Empa researcher Dominik Brunner, together with colleagues from Utrecht University and the Austrian Central Institute for Meteorology and Geophysics, is investigating how much plastic is trickling down on us from the atmosphere. According to the study, some nanoplastics travel over 2000 kilometers through the air. According to the figures from the measurements about 43 trillion miniature plastic particles land in Switzerland every year. Researchers still disagree on the exact number. But according to estimates from the study, it could be as much as 3,000 tonnes of nanoplastics that cover Switzerland every year, from the remote Alps to the urban lowlands. These estimates are very high compared to other studies, and more research is needed to verify these numbers

The study is uncharted scientific territory because the spread of nanoplastics through the air is still largely unexplored.

The scientists studied a small area at an altitude of 3106 meters at the top of the mountain "Hoher Sonnenblick" in the "Hohe Tauern" National Park in Austria.
Every day, and in all weather conditions, scientists removed a part of the top layer of snow around a marker at 8 AM and carefully stored it. Contamination of the samples by nanoplastics in the air or on the scientists' clothes was a particular challenge. In the laboratory, the researchers sometimes had to remain motionless when a colleague handled an open sample.

The origin of the tiny particles was traced with the help of European wind and weather data. The researchers could show that the greatest emission of nanoplastics into the atmosphere occurs in densely populated, urban areas. About 30% of the nanoplastic particles measured on the mountain top originate from a radius of 200 kilometers, mainly from cities. However, plastics from the world's oceans apparently also get into the air via the spray of the waves. Around 10% of the particles measured in the study were blown onto the mountain by wind and weather over 2000 kilometers – some of them from the Atlantic.

It is estimated that more than 8300 million tonnes of plastic have been produced worldwide to date, about 60% of which is now waste. This waste erodes through weathering effects and mechanical abrasion from macro- to micro- and nanoparticles. But discarded plastic is far from the only source. Everyday use of plastic products such as packaging and clothing releases nanoplastics. Particles in this size range are so light that their movement in the air can best be compared to gases.

Besides plastics, there are all kinds of other tiny particles. From Sahara sand to brake pads, the world is buzzing through the air as abrasion. It is as yet unclear whether this kind of air pollution poses a potential health threat to humans. Nanoparticles, unlike microparticles, do not just end up in the stomach. They are sucked deep into the lungs through respiration, where their size may allow them to cross the cell-blood barrier and enter the human bloodstream. Whether this is harmful or even dangerous, however, remains to be researched.

Source:

Empa, Noé Waldmann

(c) Hologenix
01.02.2022

Hologenix: Pure White Celliant wins ISPO Textrends Award

Hologenix® is pleased to announce that its newest innovation – pure white CELLIANT® – is a Top Ten winner in the Fibers & Insulation Category of ISPO Textrends Fall/Winter 2023/24. Twice a year, ISPO recognizes innovative fabrics and components that are used to manufacture sports apparel. It’s no surprise that this innovation, whereby CELLIANT infrared technology can be embedded in fibers and for those fibers to be pure white, has achieved this honor. Pure white expands the potential applications of CELLIANT to crisp white performance and athleisure apparel, athletic uniforms and jerseys, towels, bedding, baby clothes, medical apparel and more, while maintaining its well-known wellness benefits. Pure white is the foundation that makes delicate pastel fabrics, as well as any color, possible.

Hologenix® is pleased to announce that its newest innovation – pure white CELLIANT® – is a Top Ten winner in the Fibers & Insulation Category of ISPO Textrends Fall/Winter 2023/24. Twice a year, ISPO recognizes innovative fabrics and components that are used to manufacture sports apparel. It’s no surprise that this innovation, whereby CELLIANT infrared technology can be embedded in fibers and for those fibers to be pure white, has achieved this honor. Pure white expands the potential applications of CELLIANT to crisp white performance and athleisure apparel, athletic uniforms and jerseys, towels, bedding, baby clothes, medical apparel and more, while maintaining its well-known wellness benefits. Pure white is the foundation that makes delicate pastel fabrics, as well as any color, possible.

Pure white CELLIANT still captures and converts body heat into infrared energy, increasing local circulation, aiding in temperature regulation and promoting stronger performance, faster recovery and better sleep. Pure white CELLIANT is also still made from ethically sourced minerals from the earth and is available in nylon, polyester and recycled polyester fibers, while retaining the natural characteristics of the polymer.

This award follows on the heels of the 2022/23 ISPO Textrends Awards finalist selection of CELLIANT viscose in the Fibers and Insulations category, which features CELLIANT embedded into plant-based fibers.  “We are honored to achieve this recognition from ISPO for our pure white CELLIANT,” said Courtney OKeefe, Chief Supply Chain Officer for Hologenix. “This new formulation took years of work to achieve and is a testament to the dedication and talent of our global research team. We are also very proud to be able to state that we now have two ISPO-recognized fibers.”

More information:
Hologenix Celliant Sportswear Fibers
Source:

Hologenix, LLC / Sarah P. Fletcher Communications 

(c) Messe Frankfurt (HK) Ltd.
21.01.2022

Promising conditions for Cinte Techtextil China in September

Promising conditions in the technical textiles and nonwovens market are expected to provide ample opportunities for suppliers at this year’s Cinte Techtextil China. The fair, which last year saw 366 exhibitors and 14,868 visits, will take place from 6 – 8 September 2022 at the Shanghai New International Expo Centre. Flexible exhibiting options will once again be available for overseas companies.

Ms Wendy Wen, Senior General Manager of Messe Frankfurt (HK) Ltd, explained the positive conditions that exhibitors should expect at the fair thusly: “The pandemic has led to a surge in Chinese exports of both technical textiles and nonwovens, the latter in particular. The country remains the largest supplier of nonwovens, comprising one-third of the global total, yet still requires the advanced offerings of overseas machinery suppliers, as well as supplies of raw materials, to support its export production.”

Promising conditions in the technical textiles and nonwovens market are expected to provide ample opportunities for suppliers at this year’s Cinte Techtextil China. The fair, which last year saw 366 exhibitors and 14,868 visits, will take place from 6 – 8 September 2022 at the Shanghai New International Expo Centre. Flexible exhibiting options will once again be available for overseas companies.

Ms Wendy Wen, Senior General Manager of Messe Frankfurt (HK) Ltd, explained the positive conditions that exhibitors should expect at the fair thusly: “The pandemic has led to a surge in Chinese exports of both technical textiles and nonwovens, the latter in particular. The country remains the largest supplier of nonwovens, comprising one-third of the global total, yet still requires the advanced offerings of overseas machinery suppliers, as well as supplies of raw materials, to support its export production.”

Ms Wen continued: “Domestically, China is seeing increasing consumption of functional apparel, sportswear and personal protection items. Heightened health and sanitary regulations and new hygiene habits will also continue to drive demand, especially for nonwovens, well into the future. There has also been a post-pandemic boost in demand for filter, greenhouse covering and high-density fabrics amongst others. All of this adds up to a wealth of opportunities for overseas companies to take advantage of, as was experienced in the 2021 edition of the fair.”

Exhibitor and visitor experiences in 2021
“Our organisation promotes US cotton and we hope to use this platform to meet more companies and brands in the nonwovens industry who are interested in US cotton, and to meet up with old friends to discuss the current situation and industry trends. We also found some new potential clients this time.” Mr Eric Ni, Senior Manager, China Supply Chain Marketing, Fabrics, Garments and Nonwovens, Cotton Council International, USA

“Cinte Techtextil China is a professional exhibition that brings together cutting-edge technologies and products, allowing us to quickly learn about innovative technology trends in the industry. I’ve been particularly impressed by the biodegradable products in the Innovation Showcase. In addition, I am sourcing mask-related products and mops, and I have found some companies that I’m interested in.” Ms Claire Zhang, Senior Scientist, Personal Health, Philips Research China, Philips (China) Investment Co Ltd, China

Source:

Messe Frankfurt (HK) Ltd.

(c) Monfort
Full configuration of the Monforts and KMA Umwelttechnik line.
20.01.2022

Monforts: MonforClean brings Energy Savings for Albarrie

Albarrie – a major player in North America’s industrial nonwovens industry – is now benefiting from one of the first Monforts Montex stenter installations equipped with the full range of MonforClean heat recovery and exhaust air purification technologies.

With the new three-chamber Montex stenter at its plant in Barrie, Ontario, the Canadian company is treating specialised needlepunched nonwovens up to 4mm thick. These have applications in a wide range of filter media and performance fabrics.

The new Montex is enabling Albarrie to heat set and dry its materials to produce denser, higher quality fabrics which can also be finished and delivered to customers more rapidly.

Across timezones
It took a crew of skilled millwrights, electricians and product specialists to build the line which was delivered in 11 shipping containers to Albarrie’s production facility. The line was originally scheduled to be fully operational in the Spring of 2020, but the ongoing global Covid-19 pandemic inevitably led to several delays during the start-up and commissioning process.

Albarrie – a major player in North America’s industrial nonwovens industry – is now benefiting from one of the first Monforts Montex stenter installations equipped with the full range of MonforClean heat recovery and exhaust air purification technologies.

With the new three-chamber Montex stenter at its plant in Barrie, Ontario, the Canadian company is treating specialised needlepunched nonwovens up to 4mm thick. These have applications in a wide range of filter media and performance fabrics.

The new Montex is enabling Albarrie to heat set and dry its materials to produce denser, higher quality fabrics which can also be finished and delivered to customers more rapidly.

Across timezones
It took a crew of skilled millwrights, electricians and product specialists to build the line which was delivered in 11 shipping containers to Albarrie’s production facility. The line was originally scheduled to be fully operational in the Spring of 2020, but the ongoing global Covid-19 pandemic inevitably led to several delays during the start-up and commissioning process.

Energy savings
The Albarrie Montex line’s MonforClean capabilities include an air-to-air cross flow heat exchanger and an electrostatic precipitator providing the ability to purify the exhaust air and to recover energy to a maximum of 22,500 cubic metres of air per hour, resulting in a radical reduction in the conventional heat supply required. The MonforClean was developed in cooperation with partner KMA Umwelttechnik, based in Königswinter, Germany.

The fully automated system is powered by a Siemens SPS S7 controller and KP 700 touch panel from which the recycled energy can be continuously monitored and savings calculated.

The three-chamber Montex stenter is fitted with the latest Monforts Qualitex 800 PLC control system with WebUI, providing ease of operation, a full operating cost overview and maintenance monitoring.

Source:

Monfort

(c) BioRECO2ver Project
19.01.2022

nova-Institute: BioRECO2VER project - Conversion of CO2 into chemical building blocks

CO2 as renewable carbon source
Carbon is the main element in numerous materials used in industrial processes and in our daily lives. It is currently mostly provided from fossil sources. But what if carbon could be used directly from CO2 emissions? Biotechnology shows particularly great potential for the eco-effective conversion of climate-damaging CO2 emissions into valuable basic chemicals. A consortium of 12 partners investigated this pathway in the EU-funded BioRECO2VER project, examining the conversion of CO2 emissions from refineries and the cement industry into the chemical building blocks isobutene (C4H8) and lactate (C2H6O3).

CO2 as renewable carbon source
Carbon is the main element in numerous materials used in industrial processes and in our daily lives. It is currently mostly provided from fossil sources. But what if carbon could be used directly from CO2 emissions? Biotechnology shows particularly great potential for the eco-effective conversion of climate-damaging CO2 emissions into valuable basic chemicals. A consortium of 12 partners investigated this pathway in the EU-funded BioRECO2VER project, examining the conversion of CO2 emissions from refineries and the cement industry into the chemical building blocks isobutene (C4H8) and lactate (C2H6O3).

Innovative chemo-enzymatic concept for CO2 Capture
Project partner Luleå University of Technology (LTU) focused on the first process step of capturing and concentrating CO2 from industrial point sources. Their team developed a hybrid chemo-enzymatic process consisting of a novel solvent blend and an ultrastable carbonic anhydrase (CA) enzyme. The solvent blend included an amino acid ionic liquid and a tertiary amine and displayed a good compromise between enzyme compatibility, absorption rate, capacity and desorption potential. In addition, LTU generated ultrastable enzyme mutants that showed 50% increased resistance to selected flue gas inhibitors compared to the original CA. This 3-component CO2 capture process was scaled up in a pilot rig, and the set-up further used for real off gas pre-treatment in the project.

Two unique pilots for biotechnological CO2 Conversion/Utilization
The biotechnological conversion of (captured) CO2 and the co-substrate hydrogen by microorganisms poses technical and economic challenges because it takes place in the liquid phase and the substrates are gases which are poorly soluble. The BioRECO2VER project investigated two approaches to address this: fermentation under elevated pressure and bio-electrochemistry with in situ production of hydrogen.

Pressurized fermenter
Project coordinator VITO designed a flexible and multifunctional high-pressure fermenter, customized for research activities with advanced online sensors, monitoring and control, and also including a membrane filtration unit to achieve high concentrations of the microbial biocatalysts. The set-up was broadly tested in the BioRECO2VER project both with pure CO2 and CO2-rich off-gases but can also be used for investigations involving other poorly soluble gases, such as methane, oxygen, or synthesis gas. Pressures up to 10 bar can be applied.

First solely CO2-based bio-electrochemical platform
University of Girona designed and tested a bio-electrochemical platform. The key differentiators of the pilot plant are:

  • Two parallel lines to test engineered strains and bio-electrochemical systems
  • Fully automated pilot plant capable to control key operational parameters (pCO2, pO2, pH2, pH, Temperature) to intensify the process performance
  • Solid-liquid separation unit (membrane) to recover the planktonic cells and return them into the bio-electrochemical systems.

This unique infrastructure will be used beyond the project to support further research and development activities in the broad area of CO2 capture and conversion.

Source:

nova-Institut GmbH

(c) ARMALITH®
13.01.2022

Armalith presents Armalith 2.0® and its portfolio

«Armalith® is the story of my passions. Firstly textiles, which opened the doors to the great ready-to-wear and haute couture houses. Then motorcycling, an incredible vehicle for finding freedom and meeting people. In 2003, I combined these two passions by creating Armalith® with one idea in mind: to offer the best possible protection to bikers without compromising on the comfort and authenticity of a real pair of jeans. Today, Armalith 2.0® is the denim of choice for the most prestigious brands for their abrasion protection equipment.» Pierre-Henry Servajean, Armalith® MK Support manager.

Armalith 2.0 in facts:

«Armalith® is the story of my passions. Firstly textiles, which opened the doors to the great ready-to-wear and haute couture houses. Then motorcycling, an incredible vehicle for finding freedom and meeting people. In 2003, I combined these two passions by creating Armalith® with one idea in mind: to offer the best possible protection to bikers without compromising on the comfort and authenticity of a real pair of jeans. Today, Armalith 2.0® is the denim of choice for the most prestigious brands for their abrasion protection equipment.» Pierre-Henry Servajean, Armalith® MK Support manager.

Armalith 2.0 in facts:

  • The mechanical qualities of leather with the comfort of denim
  • Extreme resistance to cuts, traction, tears and abrasion
  • High UV resistance that preserves its mechanical properties
  • One layer for resistance that is superior to any lined products

High technology for high security
The heart of the armour is made of UHMWPE (high molecular weight polyethylene). This high resistance fiber comes from aerospace research; it is used for space module re-entry ropes, military armour, mooring cables for offshore platforms and more. This core is then covered with a cotton fiber using an exclusive and patented process, and combined with LYCRA® dualFX® technology for a powerful and durable stretch.

High resistance for high protection
High-tech integrated into authentic denim for unique comfort and protection, Armalith 2.0® meets the most demanding standards such as Darmstadt and Cambridge, which are more scientific than the CE certification.
Armalith 2.0® is available in 3 grades - A, AA and AAA - to cover all needs from urban use to maximum protection against abrasion. In its EXO (KNIT) form, Armalith 2.0® can be used as a lining to increase resistance in specific areas without using other uncomfortable solutions.

High comfort for high style
Safety in a single layer of fabric, comfort, softness, stretchability, and style! Armalith 2.0® is a real denim. Soft, supple, comfortable, breathable and hydrophilic, it allows all the usual textures, dyes, prints and finishing in low temperatures.

Armalith 2.0® is an ethical and responsible denim

  • GRS cotton sourced from Greece.
  • Designed in France, manufactured and produced on a single site - spinning, dyeing, indigo, weaving, finishing - at Tejidos Royo in Spain.
  • UHMWPE fibre requires half the energy to produce than aramids.
  • The UHMWPE fibre used under the ARMALITH 2.0® patent is continuous (no energy-intensive cracking) and untextured (no energy-intensive texturing).
  • All Armalith 2.0® denim manufacturing processes are carried out at low temperatures: a world first for stretch fabrics.
  • No heavy metals used in the pigments, the indigo is made using a slow, cold, waterless process
  • Resistant to more than a thousand washes for greater longevity and without loss of elasticity.
More information:
Armalith Denim Leather stretch fabric
Source:

ARMALITH® / VIA VENETO

(c) Kornit
13.01.2022

Blur uses Kornit Digital for Scalability, Operational Versatility, 24-Hour Production

Kornit Digital Ltd. announced that Portuguese textile specialist Blur has installed the Kornit Presto S with Softener solution for sustainable, single-step direct-to-fabric production of multiple fabrics in any quantity. The print services provider, which supports the production needs of high fashion brands has previously installed multiple Kornit Atlas and Avalanche systems for industrial-scale digital direct-to-garment (DTG) production on demand.

Using Kornit’s efficient, eco-conscious, proprietary technology and consumables, Blur provides rapid fulfillment of orders ranging from a single piece to mass production, with an average order of about 500 items. Since implementing the Kornit Presto S, the system has been in operation day and night, producing samples during normal business hours and fulfilling diverse incoming orders overnight.

Kornit Digital Ltd. announced that Portuguese textile specialist Blur has installed the Kornit Presto S with Softener solution for sustainable, single-step direct-to-fabric production of multiple fabrics in any quantity. The print services provider, which supports the production needs of high fashion brands has previously installed multiple Kornit Atlas and Avalanche systems for industrial-scale digital direct-to-garment (DTG) production on demand.

Using Kornit’s efficient, eco-conscious, proprietary technology and consumables, Blur provides rapid fulfillment of orders ranging from a single piece to mass production, with an average order of about 500 items. Since implementing the Kornit Presto S, the system has been in operation day and night, producing samples during normal business hours and fulfilling diverse incoming orders overnight.

Mariano Dias, CEO at Blur, believes Kornit technology empowers his business to adapt quickly to the constantly evolving needs of his clients, which include both larger established brands seeking large quantities and ambitious designers seeking to build a brand with limited risk or investment. In many cases, they are fulfilling different types of designs for clients serving both Europe and North American markets.
“The quality is just outstanding, and some clients only want to print with Kornit technology”, said Dias. “We are extremely happy with Kornit’s collaboration, and our printers are working perfectly around the clock. Any textile printing company looking to move into fashion and work with famous brands will need both roll-to-roll and DTG capabilities. Our recommendation for success is to buy the Kornit Atlas and Kornit Presto printers.”

He added that Blur’s success with its current Kornit systems, as well as increased demand for sustainably-produced textiles, has the business considering the addition of a second Kornit Presto S to accommodate additional volumes.

“As with many of our customers, Blur was built around more traditional textile operations—in their case embroidery—before discovering the vast potential for growth and versatility offered by quick, efficient, digital production on demand,” said Chris Govier, Kornit Digital Europe, Middle East, and Africa President. “Whether you’re serving an internationally-known fashion house looking for more agile fulfillment and simpler supply chains, or the independent creator hoping to bring unique inspirations to life, Kornit’s product portfolio offers continuous opportunities to answer market needs, create new markets, and scale upwards under any conditions.”

Source:

Kornit / pr4u

06.01.2022

Maison & Objet Paris postponed from January to March 2022

Since few days, most countries have been facing a new wave of Covid, reinforced by the rapid expansion of the Omicron variant. Impacted by this surge, many companies among the 1,700 companies that have confirmed they will attend M&O in January at the Parc des Expositions of Paris-Nord Villepinte, indicate that they don’t want their employees to take risks and are now alerting to the disruptions they are experiencing in their operations. The obligations of compliance with isolation rules, even when people are vaccinated, and the numerous work absences are in fact starting to seriously disrupt the functioning of their services, supply or production circuits.

Moreover, facing the peak of contamination, several countries are currently taking restrictive measures regarding international travel. Measures which are now delaying or discouraging visitors from confirming their attendance. In addition, the French government has announced, December 27th 2021 a 2.000 people gauge for major events, so probably fairs such as Maison&Objet Paris.

Since few days, most countries have been facing a new wave of Covid, reinforced by the rapid expansion of the Omicron variant. Impacted by this surge, many companies among the 1,700 companies that have confirmed they will attend M&O in January at the Parc des Expositions of Paris-Nord Villepinte, indicate that they don’t want their employees to take risks and are now alerting to the disruptions they are experiencing in their operations. The obligations of compliance with isolation rules, even when people are vaccinated, and the numerous work absences are in fact starting to seriously disrupt the functioning of their services, supply or production circuits.

Moreover, facing the peak of contamination, several countries are currently taking restrictive measures regarding international travel. Measures which are now delaying or discouraging visitors from confirming their attendance. In addition, the French government has announced, December 27th 2021 a 2.000 people gauge for major events, so probably fairs such as Maison&Objet Paris.

Under these circumstances, seeking to avoid a risky situation and committed to making all efforts to ensure an optimal return on investment for exhibitors, buyers and specifiers, the SAFI decides to postpone the next session of the Maison&Objet trade event from 24th to 28th March 2022. Period for which we hope to see an improvement in the situation.

Exhibitors who have already confirmed their registration and location may have the same location conditions, which will allow them to keep the same stand showcase. Likewise, visitors who have already ordered their badges for the January edition will of course have access to the show from March 24th to 28th, 2022.

With an opening scheduled for the day before, Maison&Objet In The City, an event organised on the sidelines of the Maison&Objet fair and offering a journey of discoveries in the heart of Parisian showrooms, will be held from 23 to 28 March 2022.

By postponing the fair until the end of Q1, SAFI wishes to bring together the best operational and healthy conditions to allow actors in the art of living, decoration, and design to be inspired, to accelerate their development and to forge new business relationships

In summary: the next editions of the Maison&Objet fairs will therefore be: March 24th - 28th, 2022 + September 8th - 12th, 2022

More information:
Maison & Objet Omikron
Source:

S2H Communication

03.01.2022

Physical ClusterXchange - Discovering smart materials in Czech Republic

Under the ClusterXchange pilot scheme, the EXTRATEX partnership organised a 5-day exchange in Czech Republic, hosted by CLUTEX (cluster for technical textile).

15 participants visited strategic and innovative companies in the field of smart materials and advances technologies, as well as research centres and the Liberec University.

During the exchange, 92 B2B meetings were organized between local companies and the exchange participants, with 75% of the contacts established leading to follow-ups after the conclusion of the exchange. This collaboration laid the foundation for potential cross-border and cross-sector business collaboration, and participants of the physical exchange improved their competences in the field of smart materials and advanced technologies.

Under the ClusterXchange pilot scheme, the EXTRATEX partnership organised a 5-day exchange in Czech Republic, hosted by CLUTEX (cluster for technical textile).

15 participants visited strategic and innovative companies in the field of smart materials and advances technologies, as well as research centres and the Liberec University.

During the exchange, 92 B2B meetings were organized between local companies and the exchange participants, with 75% of the contacts established leading to follow-ups after the conclusion of the exchange. This collaboration laid the foundation for potential cross-border and cross-sector business collaboration, and participants of the physical exchange improved their competences in the field of smart materials and advanced technologies.

According to a testimony from the company Bipier Srl, their participation in the exchange allowed the establishment of two important working relationships with Bcb Informatica Y Control and Vyskummy Ustav Chemickych (Research Institute for Man-Made Fibers). This cooperation wil allow Bipier Srl to equip their machines with quality temperature control, and to expand the distribution of their products.

More information:
EXTRATEX Smart textiles
Source:

ECCP

Political Tailwind for Alternative Carbon Sources (c) Renewable Carbon Initiative
European Policy under the new green deal
22.12.2021

Political Tailwind for Alternative Carbon Sources

  • More than 30 leading pioneers of the chemical and material sector welcome the latest political papers from Brussels, Berlin and Düsseldorf

The political situation for renewable carbon from biomass, CO2 and recycling for the defossilisation of the chemical and materials industry has begun to shift fundamentally in Europe. For the first time, important policy papers from Brussels and Germany take into consideration that the term decarbonisation alone is not sufficient, and that there are important industrial sectors with a permanent and even growing carbon demand. Finally, the need for a sustainable coverage of this carbon demand and the realisation of sustainable carbon cycles have been identified on the political stage. They are elemental to the realisation of a sustainable chemical and derived materials industry.

  • More than 30 leading pioneers of the chemical and material sector welcome the latest political papers from Brussels, Berlin and Düsseldorf

The political situation for renewable carbon from biomass, CO2 and recycling for the defossilisation of the chemical and materials industry has begun to shift fundamentally in Europe. For the first time, important policy papers from Brussels and Germany take into consideration that the term decarbonisation alone is not sufficient, and that there are important industrial sectors with a permanent and even growing carbon demand. Finally, the need for a sustainable coverage of this carbon demand and the realisation of sustainable carbon cycles have been identified on the political stage. They are elemental to the realisation of a sustainable chemical and derived materials industry.

The goal is to create sustainable carbon cycles. This requires comprehensive carbon management of renewable sources, which includes carbon from biomass, carbon from Carbon Capture and Utilisation (CCU) – the industrial use of CO2 as an integral part – as well as mechanical and chemical recycling. And only the use of all alternative carbon streams enables a true decoupling of the chemical and materials sector from additional fossil carbon from the ground. Only in this way can the chemical industry stay the backbone of modern society and transform into a sustainable sector that enables the achievement of global climate goals. The Renewable Carbon Initiative’s (RCI) major aim is to support the smart transition from fossil to renewable carbon: utilising carbon from biomass, CO2 and recycling instead of additional fossil carbon from the ground. This is crucial because 72% of the human-made greenhouse gas emissions are directly linked to additional fossil carbon. The RCI supports all renewable carbon sources available, but the political support is fragmented and differs between carbon from biomass, recycling or carbon capture and utilisation (CCU). Especially CCU has so far not been a strategic objective in the Green Deal and Fit-for-55.

This will change fundamentally with the European Commission's communication paper on “Sustainable Carbon Cycles” published on 15 December. The position in the paper represents an essential step forward that shows embedded carbon has reached the political mainstream – supported by recent opinions from members of the European parliament and also, apparently, by the upcoming IPCC assessment report 6. Now, CCU becomes a recognised and credible solution for sustainable carbon cycles and a potentially sustainable option for the chemical and  material industries. Also, in the political discussions in Brussels, the term “defossilation” is appearing more and more often, complementing or replacing the term decarbonisation in those areas where carbon is indispensable. MEP Maria da Graça Carvahlo is among a number of politicians in Brussels who perceive CCU as an important future industry, putting it on the political map and creating momentum for CCU. This includes the integration of CCU into the new Carbon Removal Regime and the Emission Trading System (ETS).

As the new policy documents are fully in line with the strategy of the RCI, the more than 30 member companies of the initiative are highly supportive of this new development and are ready to support policy-maker with data and detailed suggestions for active support and the realisation of sustainable carbon cycles and a sound carbon management. The recent political papers of relevance are highlighted in the following.

Brussels: Communication paper on “Sustainable Carbon Cycles”
On 15 December, the European Commission has published the communication paper “Sustainable Carbon Cycles” . For the first time, the importance of carbon in different industrial sectors is clearly stated. One of the key statements in the paper is the full recognition of CCU for the first time as a solution for the circular economy, which includes CCU-based fuels as well. The communication paper distinguishes between bio-based CO2, fossil CO2 and CO2 from direct air capture when addressing carbon removal and it also announces detailed monitoring of the different CO2 streams. Not only CCU, but also carbon from the bioeconomy is registered as an important pillar for the future. Here, the term carbon farming has been newly introduced, which refers to improved land management practices that result in an increase of carbon sequestration in living biomass, dead organic matter or soils by enhancing carbon capture or reducing the release of carbon. Even though the list of nature-based carbon storage technologies is non-exhaustive in our view, we strongly support the paper’s idea to deem sustainable land and forest management as a basis for the bioeconomy more important than solely considering land use as a carbon sink. Surprisingly, chemical recycling, which is also an alternative carbon source that substitutes additional fossil carbon from the ground (i.e. carbon from crude oil, natural gas or from coal), is completely absent from the communication paper.

Berlin: Coalition paper of the new German Government: “Dare more progress – alliance for freedom, justice and sustainability”
The whole of Europe is waiting to see how the new German government of Social Democrats, Greens and Liberals will shape the German climate policy. The new reform agenda focuses in particular on solar and wind energy as well as especially hydrogen. Solar energy is to be expanded to 200 GW by 2030 and two percent of the country's land is to be designated for onshore wind energy. A hydrogen grid infrastructure is to be created for green hydrogen, which will form the backbone of the energy system of the future – and is also needed for e-fuels and sustainable chemical industry, a clear commitment to CCU. There is a further focus on the topic of circular economy and recycling. A higher recycling quota and a product-specific minimum quota for the use of recyclates and secondary raw materials should be established at European level. In the coalition paper, there is also a clear commitment to chemical recycling to be found. A significant change for the industry is planned to occur in regards to the so-called “plastic tax” of 80 cents per kilogram of non-recycled plastic packaging. This tax has been implemented by the EU, but most countries are not passing on this tax to the manufacturers and distributors, or only to a limited extent. The new German government now plans to fully transfer this tax over to the industry.

Düsseldorf: Carbon can protect the climate – Carbon Management Strategy North Rhine-Westphalia (NRW)
Lastly, the RCI highly welcomes North Rhine-Westphalia (NRW, Germany) as the first region worldwide to adopt a comprehensive carbon management strategy, a foundation for the transformation from using additional fossil carbon from the ground to the utilisation of renewable carbon from biomass, CO2 and recycling. For all three alternative carbon streams, separate detailed strategies are being developed to achieve the defossilisation of the industry. This is all the more remarkable as North Rhine-Westphalia is the federal state with the strongest industry in Germany, in particular the chemical industry. And it is here, of all places, that a first master plan for the conversion of industry from fossil carbon to biomass, CO2 and recycling is implemented. If successful, NRW could become a global leader in sustainable carbon
management and the region could become a blueprint for many industrial regions.

20.12.2021

EFI: New Innovations in Digital Textile at EFI Reggiani Open House

During an expansive, three-day Electronics For Imaging, Inc. open house this month at the company’s EFI™ Reggiani industrial textile printer facility, textile and apparel manufacturers witnessed first-hand the market-leading innovations that provide users with new opportunities. The December open house, which drew more than 70 attendees from over 23 different European, South American, and Middle Eastern countries, featured informative sessions with product experts on a diverse range of topics, covering new and trending market applications for textile manufacturers.

Attendees witnessed live demonstrations of eight advanced digital printers during the open house, including the new EFI Reggiani HYPER, EFI Reggiani TERRA Silver scanning/multi-pass printer, and EFI Reggiani BLAZE as well as the EFI Reggiani BOLT – the award-winning single-pass offering that is the one of the fastest digital textile printers.

During an expansive, three-day Electronics For Imaging, Inc. open house this month at the company’s EFI™ Reggiani industrial textile printer facility, textile and apparel manufacturers witnessed first-hand the market-leading innovations that provide users with new opportunities. The December open house, which drew more than 70 attendees from over 23 different European, South American, and Middle Eastern countries, featured informative sessions with product experts on a diverse range of topics, covering new and trending market applications for textile manufacturers.

Attendees witnessed live demonstrations of eight advanced digital printers during the open house, including the new EFI Reggiani HYPER, EFI Reggiani TERRA Silver scanning/multi-pass printer, and EFI Reggiani BLAZE as well as the EFI Reggiani BOLT – the award-winning single-pass offering that is the one of the fastest digital textile printers.

EFI Reggiani HYPER – a fast scanning digital printer
The new EFI Reggiani HYPER is a scanning printer available in 1.8-metre, 2.4-metre or 3.4-metre widths. The Reggiani HYPER model targets the industrial high-speed segment of the multi-pass textile printing sector.

With an up to eight-colour configuration, it prints at speeds up to 13 linear metres per minute in two-pass production mode. The new printer is suitable for high-quality production on knitted or woven fabrics and is designed with smart technology that enables it to be integrated into Industry 4.0 projects.

Sustainable direct-to-textile printing with the EFI Reggiani TERRA Silver
The new-version TERRA Silver printer is part of EFI’s complete TERRA line-up of pigment ink printer solutions. It allows print service providers to enter the world of industrial textile with a short, smart and green production process.
The printer also features:

  • A new recirculating ink system for superior reliability and minimum maintenance
  • Several printing modes to ensure maximum flexibility in terms of design capability
  • New, real-time image processing that eliminates time spent in image pre-calculations
  • A user friendly, intuitive interface
  • A more-efficient polymerisation process that takes place as printed textile goes through the printer’s on-board dryer.

EFI Reggiani BLAZE, an ideal entry solution for industrial textile printing
The EFI Reggiani BLAZE printer is designed to give textile companies the opportunity to enter the digital textile printing market with a compact solution. The new, 1.8-metre-wide printer offers an innovative, low-maintenance, continuous recirculation ink system equipped with a level sensor and degassing as well as a print head crash protective system for longer printhead life and superior uptime.

The upgraded EFI Reggiani BOLT – one of the fastest digital textile printers
In 2021, the EFI Reggiani BOLT received a combination of hardware and software enhancements that minimise artifacts, compensating for missing nozzles that may occur over time and enhancing uniformity to deliver smoother solid colours. The upgrade also delivers improved quality and smoother gradients, plus it enables faster printhead replacement and drastically increases file processing speed by up to 200% for large, complex files.

Source:

EFI GmbH

Iluna Group and Maglificio Ripa announce Partnership (c) Iluna Group / Maglificio Ripa
17.12.2021

Iluna Group and Maglificio Ripa announce Partnership

Iluna Group and Maglificio Ripa announce a strategic collaboration, each maintaining its own identity and independence, based on the complementarity of the proposal and the convergence of intentions for a new and more functional way of partnership.

Iluna Group, a leader in the production of smart lace, and Maglificio Ripa, internationally recognized for the production of premium and responsible jersey, both established in common sectors - from underwear to beachwear and sportswear - formally launched this collaboration during the MarediModa show in Cannes with a joint double stand where visitors could discover the latest collections of the two companies and also imagine new designs and solutions for sustainable fashion.

Iluna Group and Maglificio Ripa announce a strategic collaboration, each maintaining its own identity and independence, based on the complementarity of the proposal and the convergence of intentions for a new and more functional way of partnership.

Iluna Group, a leader in the production of smart lace, and Maglificio Ripa, internationally recognized for the production of premium and responsible jersey, both established in common sectors - from underwear to beachwear and sportswear - formally launched this collaboration during the MarediModa show in Cannes with a joint double stand where visitors could discover the latest collections of the two companies and also imagine new designs and solutions for sustainable fashion.

"We are living in a moment of strong change, from the wave of sustainability that is finally sweeping the fashion world to new market scenarios. And we are convinced that collaboration is the key to face these new challenges. In Maglificio Ripa we saw a complementary and unique partner with whom we can reach partners, customers and suppliers in a more complete way." comments Furio Annovazzi, CEO of Iluna Group. "Ours is not a union between companies but a new model of partnership, a sort of strategic symbiosis aimed at developing together new paths that can lead the both of us both to growth. Our collections, presented in the same context, can nurture the creativity of customers at a time when the stylistic contaminations are increasingly pronounced," adds Luca Bianco, CEO of Maglificio Ripa.
 
Furthermore, Iluna Group and Maglificio Ripa jointly created their new campaign with a photo shoot and video clip as well as jointly developed a trend scenario that allowed both companies to better embrace the evolving market by sharing information, perspectives and ideas.

Source:

GB Network

13.12.2021

TMAS: Digitalisation demands streamlined solutions

Fully integrated production lines from single source suppliers have increasingly become the norm in the textile industry and make complete sense in meeting today’s complex supply chain needs, according to TMAS – the Swedish Textile Machinery Association.

“Over the past few decades, textile mills have transitioned from consisting of collections of individual machines serviced and maintained largely by in-house mechanics as well as separate supplier companies for each part of the production line,” says TMAS Secretary General Therese Premler-Andersson. “Those in-house engineering service teams have diminished over the years, while the introduction of electronic drive systems in the 1980s and 90s also put an increased emphasis on the need for third party electrical engineers, operating separately to the machine builders.

“Subsequently, mechanical machines and electronic drive systems became much more integrated, and more recently, with the advent of digitalisation, entire production lines are becoming centrally controlled with remote, instantaneous connections to their suppliers for service and maintenance.

Fully integrated production lines from single source suppliers have increasingly become the norm in the textile industry and make complete sense in meeting today’s complex supply chain needs, according to TMAS – the Swedish Textile Machinery Association.

“Over the past few decades, textile mills have transitioned from consisting of collections of individual machines serviced and maintained largely by in-house mechanics as well as separate supplier companies for each part of the production line,” says TMAS Secretary General Therese Premler-Andersson. “Those in-house engineering service teams have diminished over the years, while the introduction of electronic drive systems in the 1980s and 90s also put an increased emphasis on the need for third party electrical engineers, operating separately to the machine builders.

“Subsequently, mechanical machines and electronic drive systems became much more integrated, and more recently, with the advent of digitalisation, entire production lines are becoming centrally controlled with remote, instantaneous connections to their suppliers for service and maintenance.

“In this context, the integration of machinery and automation specialists as single-source suppliers makes perfect sense, while partnerships between machine builders and their customers have never been more important.”

The recent acquisition of Nowo textile machinery from its previous owner, Brandstones Ab Oy, by TMAS member ACG Kinna, she adds, is a good example of this general trend.

Nowo, headquartered in Turku, Finland, designs, manufactures and exports high-end textile production machinery mainly for the fibre processing industry. At the end of the 1980s it introduced the highly successful Nowo Vac pillow filling system, which has been its best-selling system, alongside the Noworoll ball fibre machine, introduced in the 1990s.

Nowo’s machine range covers the entire production process from bale opening to weighing and filling, and complete production lines are tailored to the specific needs of customers. The company can also deliver individual machines such as bale openers, cards, cross-lappers, pickers, mixing devices, material silos, sucking devices, anti-static units etc. Seven patents cover the company’s technologies.

Founded in 1977, ACG Kinna Automatic, based in Skene in Sweden, specialises in customised and cost-efficient solutions for the production of pillows and quilts. All of its design, manufacturing and final line testing is carried out in Sweden and the reliability and longevity of its machines has earned it the trust of the world’s largest furniture and home decoration retailers and Europe’s largest manufacturer of pillows and duvets, among many customers.

Source:

TMAS / AWOL Media

(c) Messe Frankfurt, deepak@deepakdavda.com
13.12.2021

Techtextil India: First post-lockdown edition with overwhelming responsive from industry

After three-days of product sourcing and business networking, Techtextil India 2021 in Mumbai concluded in a strong and positive note. The trade fair emerged as a crucial meeting place for the technical textile players to rebuild their supplier links, promote industry integration and engage in lucrative knowledge exchange.

The eighth edition of Techtextil India stood out to be a ground-breaking business platform for the technical textile sector to build a new and strong foundation in the new normal. The aim of the new edition was to promote industry unification and business recovery across the value chain of technical textiles.

The event held at Bombay Exhibition Centre was inaugurated by major dignitaries, including Shri Ajit Chavan, Secretary – Textiles Committee, Ministry of Textiles, Government of India. Over the course of its three buzzing days, the show garnered an attendance of 4,087 visitors drawn by live demonstration of latest products, technologies and innovations exhibited by over 150 technical textile brands on the show floor.

After three-days of product sourcing and business networking, Techtextil India 2021 in Mumbai concluded in a strong and positive note. The trade fair emerged as a crucial meeting place for the technical textile players to rebuild their supplier links, promote industry integration and engage in lucrative knowledge exchange.

The eighth edition of Techtextil India stood out to be a ground-breaking business platform for the technical textile sector to build a new and strong foundation in the new normal. The aim of the new edition was to promote industry unification and business recovery across the value chain of technical textiles.

The event held at Bombay Exhibition Centre was inaugurated by major dignitaries, including Shri Ajit Chavan, Secretary – Textiles Committee, Ministry of Textiles, Government of India. Over the course of its three buzzing days, the show garnered an attendance of 4,087 visitors drawn by live demonstration of latest products, technologies and innovations exhibited by over 150 technical textile brands on the show floor.

The event received an overwhelming response, reflecting industry’s keen interest to explore new developments and opportunities in technical textiles. In regards to the same, Mr Abhijit Kulkarni, President – Textile Engineering Group, A.T.E. India, stated: “It was the first and best physical show also on hybrid mode filled with enthusiastic buyers and customers who visited our booth and had very fruitful discussions with us. Several leading textile manufacturers visited our stalls, including: Strata Geosystems India, SKAPS Industries, Reliance Composites, Paramount Textiles, and Welspun, to name a few.”

Alok Masterbatches Pvt Ltd, Khosla Profile Pvt Ltd, ATE Group, Lucky International, Meera Industries Limited, Park Non-Woven Pvt Ltd, Sarex Chemicals, SICAM, Suntech Geotextile Pvt Ltd and Weavetech Engineers, were among the leading Indian companies exhibiting at the show.

The significance of the three-day fair was further elevated by the German pavilion. Technical textile manufacturers from Germany, such as Autefa Solution Germany GmbH, DILO Systems GmbH, Emtec Electronic GmbH, Georg Sahm GmbH & Co, Karl Mayer Verwaltungsgesellschaft mbH, Merz Maschinenfabrik GmbH and Oerlikon Barmag Zweigniederlassung der Oerlikon Textile GmbH & Co, displayed their latest technologies on the show floor, which garnered significant attention from the Indian buyers.

The first Digital Symposium was another highlight of Techtextil India 2021. The forum delved into a series of crucial topics in technical textiles discussing PLI schemes, FDI opportunities and policies, investment opportunities in Tamil Nadu, & New Investment Opportunities, Sustainable Technical Textiles and Global sustainable approach for Textiles with Antimicrobial Performance.

Concluding on a successful note, Techtextil India 2021 emerged as a platform of new beginnings for the technical textiles sector and for businesses trying to retain their shape and seeking momentum after the tough pandemic phase.

Source:

Messe Frankfurt HK

06.12.2021

Sateri has been awarded the Oeko-Tex STeP certification

Sateri’s Lyocell facility in Rizhao, Shandong Province, has been awarded the Sustainable Textile Production (STeP) certification for responsible production, making it the first Lyocell producer in China to be certified to the rigorous standards set by independent Swiss-based certification organisation OEKO-TEX®. Sateri’s Lyocell facility has also obtained the highest ranking of level three in the certification assessment scoring for exemplary implementation of best manufacturing practices.

Together with its earlier achievement of the STANDARD 100 by OEKO-TEX® certification that confirms its Lyocell fibre is free from any harmful substances and complies with European standards, Sateri’s lyocell products are qualified to carry the MADE IN GREEN by OEKO-TEX® product label. This label not only attests to Sateri’s Lyocell fibre as safe and manufactured in environmentally-friendly, socially responsible and safe facility, but also the Group’s commitment to higher levels of transparency and accountability through the product traceability feature of the label.

Sateri’s Lyocell facility in Rizhao, Shandong Province, has been awarded the Sustainable Textile Production (STeP) certification for responsible production, making it the first Lyocell producer in China to be certified to the rigorous standards set by independent Swiss-based certification organisation OEKO-TEX®. Sateri’s Lyocell facility has also obtained the highest ranking of level three in the certification assessment scoring for exemplary implementation of best manufacturing practices.

Together with its earlier achievement of the STANDARD 100 by OEKO-TEX® certification that confirms its Lyocell fibre is free from any harmful substances and complies with European standards, Sateri’s lyocell products are qualified to carry the MADE IN GREEN by OEKO-TEX® product label. This label not only attests to Sateri’s Lyocell fibre as safe and manufactured in environmentally-friendly, socially responsible and safe facility, but also the Group’s commitment to higher levels of transparency and accountability through the product traceability feature of the label.

The STeP by OEKO-TEX® certification comprises three levels describing the extent to which a company has achieved sustainable production and working conditions of factories in the textile industry. The areas of assessment include chemicals management, environmental performance, environmental management, social responsibility, quality management, as well as occupational health and safety.

Sateri’s Lyocell fiber factory in Rizhao commenced operation in May 2020, with an annual output of 20,000 tonnes of Lyocell fiber. The same site houses a 5,000 tonne Lyocell pilot production line dedicated for the development of Lyocell application technology. In March 2021, the Group announced plans to expand its Lyocell annual production capacity in China up to 500,000 tonnes by 2025.

A natural and biodegradable fibre, Sateri’s Lyocell is made from wood pulp sourced from certified and sustainable plantations. It is manufactured using closed-loop technology, requiring minimal chemical input during the production process, and utilising an organic solvent that can be almost fully (99.7%) recovered and recycled.

Sateri’s Lyocell is used to produce high quality textiles and personal hygiene materials. Using a unique high technology manufacturing process, it has outstanding dry and wet strength, high uniformity and consistency, and superior quality. It blends well with various textile fibres to create different fabric styles and characteristics for wide downstream applications.

06.12.2021

Premium Group sets a strong example for the fashion industry

The Premium Group events will take place in Frankfurt am Main in the third week of January 2022, taking into account the 2G+ regulation (all participants have to be vaccinated, recovered and additionally daily tested).
 
On the basis of the current regulations of the federal government and the Hessian state government, which did not announce any further restrictions for vaccinated people last week, the fashion fairs PREMIUM and SEEK, the FASHIONTECH talks and the showcase of the new format THE GROUND will comply with the official health and hygiene regulations from 18th to January 20, 2022 in Frankfurt am Main.
 
This decision is based on the representative feedback from many protagonists of the industry, expert opinions and a close observation of the situation as well as an assessment of all measures that can be taken in Europe to ensure a safe event.

The Premium Group events will take place in Frankfurt am Main in the third week of January 2022, taking into account the 2G+ regulation (all participants have to be vaccinated, recovered and additionally daily tested).
 
On the basis of the current regulations of the federal government and the Hessian state government, which did not announce any further restrictions for vaccinated people last week, the fashion fairs PREMIUM and SEEK, the FASHIONTECH talks and the showcase of the new format THE GROUND will comply with the official health and hygiene regulations from 18th to January 20, 2022 in Frankfurt am Main.
 
This decision is based on the representative feedback from many protagonists of the industry, expert opinions and a close observation of the situation as well as an assessment of all measures that can be taken in Europe to ensure a safe event.

Four formats - one large exhibition hall
The conceptual novelty is that the PREMIUM, SEEK, THE GROUND and FASHIONTECH events will - for the first time and once - take place all together in a spacious hall, which roughly corresponds to the entire area of Station Berlin, on a total area of approx. 20,000 square meters. The resulting simplified admission management serves the safety of everyone. In this way, visitors can quickly and comfortably experience all the inspiration and concentrated brand power at once.

In addition to the security aspect, the merger of the two flagship events PREMIUM and SEEK in one large exhibition hall will bring new features, above all, in terms of content and atmosphere. Apart from an unprecedentedly strong brand portfolio, completely new synergies and energies will arise, which will make the meeting in January a unique momentum in the history of the industry.

Numerous brands have already signed-up and despite some decisions for smaller pop-up presentations, instead of large stands, the willingness to start again together and to want to send positive signals prevails! In addition to established players, many new brands also want to show their collections now.

THE GROUND - new generation, new platform
THE GROUND will give an outlook on what can be expected in summer with an exclusive press and influencer event. The Fashion Festival ‘for a young and purpose driven generation’ is an innovative platform for brands to get in direct contact with Gen Z with interactive installations, campaigns and storytelling.

At the preview event in January, 15 curated brands and key partners will present their value-based projects and products. In keynotes and panel talks, THE GROUND is dedicated to the topics most relevant to GEN Z: diversity, inclusion & sustainability.

FASHIONTECH - innovation, inspiration, content
FASHIONTECH is the content platform for fashion, technology and lifestyle. This is where decision-makers, industry insiders, communication experts and innovative minds meet to exchange experiences, discuss potential and developments, generate new leads and promote exchange between the various industries.

In addition to the core events, the Premium Group will also organize its popular evening events - due to the conditions, of course, to a slightly different extent than usual.

Source:

PREMIUM Exhibitions GmbH

29.11.2021

AVK and SMC BMC Alliance launch SMCCreate 2022 Design Conference

The European Alliance for SMC BMC and the AVK expert task force SMC/BMC are announcing they will organize together SMCCreate 2022, a conference about design in SMC and BMC composite materials. This conference will provide valuable insights in the entire product design process from idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials.

SMC and BMC are composite materials ideal for making light and intricate parts that combine structural performance with a smooth surface finish. For that reason, SMC and BMC are increasingly used in a broad range of end-use applications and markets.

Companies that have been using SMC and BMC solutions have a lot of expertise available, which can help designers to be more successful in bringing products to market. Therefore, the European Alliance for SMC BMC and the AVK expert task force SMC/BMC would like to organize together this design conference, allowing designers to learn from the experts, apply gained insights into their own designs, and broaden their horizon for new part developments.

The European Alliance for SMC BMC and the AVK expert task force SMC/BMC are announcing they will organize together SMCCreate 2022, a conference about design in SMC and BMC composite materials. This conference will provide valuable insights in the entire product design process from idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials.

SMC and BMC are composite materials ideal for making light and intricate parts that combine structural performance with a smooth surface finish. For that reason, SMC and BMC are increasingly used in a broad range of end-use applications and markets.

Companies that have been using SMC and BMC solutions have a lot of expertise available, which can help designers to be more successful in bringing products to market. Therefore, the European Alliance for SMC BMC and the AVK expert task force SMC/BMC would like to organize together this design conference, allowing designers to learn from the experts, apply gained insights into their own designs, and broaden their horizon for new part developments.

Using SMC BMC in your part design
Within the time of only 1.5 day, the SMCCreate 2022 conference will cover a wide range of subjects, all relevant for designers in their selection of materials solutions that provide performance, cost efficiency, manufacturing ability and sustainability. In particular:

  • How can SMC BMC help you to design great parts, bringing a combination of unique shapes and functional performance?
  • How can SMC BMC help you to improve sustainability?
  • What are the key steps in the design process, starting from initial idea to full production series manufacturing?
  • What are the typical design challenges and solutions?
  • How to best design for optimal manufacturing?
  • Which are the tools available for designing in SMC BMC: design software, material data, tooling considerations?
  • Practical examples of designs and components made in SMC BMC
  • What’s new in the world of SMC BMC?

Date and Location
The SMCCreate 2022 Conference will be organized on April 6-7, 2022 in Antwerp (Belgium).

(c) Kai-Chieh Kuo
17.11.2021

ITA PhD student Kai-Chieh Kuo was awarded Best Master’s Thesis Award of Walter Reiners-Stiftung

Kai-Chieh Kuo, PhD student at the Institut für Textiltechnik (ITA) of RWTH Aachen University, was awarded the German Textile Mechanical Engineering 2021 Best Master's Thesis Award for his master's thesis entitled "Modification of the tube weaving process of fine yarns for the production of woven ultra-low profile stent grafts". The prize is endowed with 3,500€. Peter D. Dornier, Chairman of the Board of the Walter Reiners-Stiftung (Foundation), virtually presented the award on the occasion of the ADD International Textile Conference on 9 November 2021.

Kai-Chieh Kuo, PhD student at the Institut für Textiltechnik (ITA) of RWTH Aachen University, was awarded the German Textile Mechanical Engineering 2021 Best Master's Thesis Award for his master's thesis entitled "Modification of the tube weaving process of fine yarns for the production of woven ultra-low profile stent grafts". The prize is endowed with 3,500€. Peter D. Dornier, Chairman of the Board of the Walter Reiners-Stiftung (Foundation), virtually presented the award on the occasion of the ADD International Textile Conference on 9 November 2021.

Minimally invasive endovascular aortic repair (EVAR) with textile stent-graft systems is nowadays a clinically established therapy procedure for the treatment of abdominal aortic aneurysms (AAA) – pathological bulges of the aorta. Due to the thick profile of the folded stent graft systems, there is currently a high risk of injuring narrowed or highly angulated access vessels from the inside during implantation. Stent graft systems with smaller profiles could provide an improvement, which could overcome complicated access routes through a lower bending stiffness. One possible approach for reducing the system profiles is the use of thin-walled tubular woven fabrics made of ultrafine multifilament yarns (≤20 dtex) as graft material.

Up to now, it has not been possible to process the fine yarns with the required high thread density (>200 threads/cm) and the available weaving technology in order to guarantee sufficient tightness against blood.

In his master's thesis, Kai-Chieh Kuo made high-density tubular weaving of ultra-fine filament yarns possible for the first time by means of suitable modifications to a shuttle loom as well as adaptations in the weaving preparation. In particular, he developed a new innovative reed technology that reduces warp thread friction during the shedding process and thus improves the process stability of the dense tube weaving process of fine yarns.

With the help of the process modification, it was then possible to produce high-density, thin-walled tubular woven fabrics, which were positively evaluated with regard to their suitability for a stent graft. Above all the potential of these tubular fabrics lies in their extremely thin-walled fabric profile, which seals well against blood. By using these new types of tubular fabrics as graft material for stent grafts, the system profile of the folded stent graft system can be reduced without having to compromise the blood tightness of the implant. The technology developed by Mr Kuo is not only applicable to stent graft systems, but also offers great possibilities for use in all other endovascular implants such as trans catheter heart valves, covered stents and small-lumen vascular prostheses.

15.11.2021

Autoneum: Flexi-Loft with high acoustic performance

The acoustic performance of components for the vehicle interior such as inner dashes or carpets depends on the noise-reducing quality as well as the geometrical adaptability and fill power of their material. With Flexi-Loft, Autoneum offers a new felt-based technology that thanks to a unique blend of recycled cotton and functional fibers reduces product weight and allows for accurate adaptation even to complex shapes. The textile material therefore provides a versatile and more sustainable alternative to foam.

The acoustic performance of components for the vehicle interior such as inner dashes or carpets depends on the noise-reducing quality as well as the geometrical adaptability and fill power of their material. With Flexi-Loft, Autoneum offers a new felt-based technology that thanks to a unique blend of recycled cotton and functional fibers reduces product weight and allows for accurate adaptation even to complex shapes. The textile material therefore provides a versatile and more sustainable alternative to foam.

In order to achieve high acoustic performance at minimum weight and maximum sustainability, Autoneum is continuously advancing its textile product portfolio. When it comes to components for the vehicle interior, for example, standard thermoplastic felts excel through their acoustic absorption, robustness and environmental friendliness. However, since felt-based materials are generally less voluminous and moldable as foam components, they require more weight to thoroughly fill the areas of varying thickness between the surface of the component and the vehicle’s body-in-white. In contrast, Autoneum’s Flexi-Loft technology is significantly lighter, more flexible and more adaptable than standard felts. In addition, the fiber-based material is versatile and clearly outperforms current foam products in terms of sustainability.

Thanks to its blend of recycled cotton and polyester fibers, Flexi-Loft substantially reduces component weight while improving geometrical adaptability and acoustic performance, especially in areas of low thickness. Thanks to the specific properties of the fibers, Flexi-Loft enables a precise adaptation to a wide variety of vehicle bodies, thereby improving the noise-insulating qualities of the respective product. Even at low weight, Flexi-Loft covers a wide range of material thicknesses, thus proving to be an ideal decoupling material for interior components with complex shapes such as inner dashes and automotive carpets. As a lightweight, flexible and sustainable alternative to both standard felts and foam, Flexi-Loft distinguishes itself by its versatile application in combination with existing Autoneum technologies such as Hybrid-Acoustics and Prime-Light. Moreover, the material helps to reduce odor and dust inside the vehicle.

Flexi-Loft consists of at least 50% recycled cotton fibers, and cut-offs generated during the manufacturing process are reclaimed, processed and then reused in the production of new felt blanks.

Autoneum is already using Flexi-Loft worldwide as an insulator for various carpets, inner dashes and other acoustic components based on its Prime-Light technology. The application of the material as an effective decoupler in inner dashes made of Hybrid-Acoustics will be launched on the European market in 2023.

More information:
Autoneum Automotive acoustic
Source:

Autoneum Management AG

11.11.2021

Berto travels zero km to support B2C brands

In 2021, Berto Industria Tessile embarked on a series of journeys through the denim supply chain, touching both B2B and B2C worlds.

The first journey of this adventure, aimed at discovering and publicizing the world of indigo and, began by talking about the collaboration with the turkish garment maker blue matters creating a green collection to be proposed to the world's top brands, continuing with “su mirura project” in the second chapter.
This project has its objective in supports, with a ready on stock fabrics, (which at this time of difficult availability of product becomes extremely relevant), young emerging talents in the world of fashion that, in our industry, both for problems related to  minimum order quantities and for problems related to financial commitments of startups, would having difficulty in the raw materials research.

In this third chapter of the personal voyage into the world of denim, Berto Industria Tessile talks about two realities that are not only made in Italy, but also made in veneto, for a zero km circularity supports.

In 2021, Berto Industria Tessile embarked on a series of journeys through the denim supply chain, touching both B2B and B2C worlds.

The first journey of this adventure, aimed at discovering and publicizing the world of indigo and, began by talking about the collaboration with the turkish garment maker blue matters creating a green collection to be proposed to the world's top brands, continuing with “su mirura project” in the second chapter.
This project has its objective in supports, with a ready on stock fabrics, (which at this time of difficult availability of product becomes extremely relevant), young emerging talents in the world of fashion that, in our industry, both for problems related to  minimum order quantities and for problems related to financial commitments of startups, would having difficulty in the raw materials research.

In this third chapter of the personal voyage into the world of denim, Berto Industria Tessile talks about two realities that are not only made in Italy, but also made in veneto, for a zero km circularity supports.

Two brands that are part of two different segments of the indigo world of b2c, one operating in the world of clothing and one in the creation of fashion accessories, but who have a common denominator between them, the use of 100% in their collections of denim fabric Berto.*

* See attached document for more information.

Source:

Berto Industria Tessile / EFFE-BI