From the Sector

The Saxon Textile Research Institute (STFI) will be presenting innovative highlights from research and development at Techtextil 2022, the international trade fair for technical textiles and nonwovens. In addition to a warp-knitted textile façade greening in a modular system and textile lightweight construction elements for the building sector made from hemp as a renewable raw material, the STFI will also be showing innovations from nonwovens research. The project optiformTEX is an example of the nonwovens competence: in this project, the mass per unit area was specifically influenced for the production of semi-finished products in the automotive sector. Furthermore, the Chemnitz Institute exhibits an ecological foam coating for protective textiles. Central highlight of the STFI's presence at the fair is also a mobile robot system, which demonstrates the automated loading of a small-scale bobbin creel.

Highlights at Techtextil 2022
The greened façade tile is a system with which large building surfaces can be cost-effectively greened through a simple, modular segment structure. In addition to insulating the building, the system has been created to meet the design requirements of a modern city centre; low-maintenance greening is made possible through functional integration in the textile carrier layer and coordinated plant selection.

Moulded components made of natural fibre nonwovens are increasingly used in the automotive sector. Conventional nonwovens currently have uniform masses per unit area. Technical solutions for load-oriented component reinforcement and the resulting optimised use of materials represent an enormous economic potential. The basic idea of “optiformTEX” was therefore to specifically influence the mass per unit area distribution in the pile before the semi-finished product is consolidated. As a result, a textile-technological process and the corresponding plant component were successfully developed.

Future-oriented materials are offered by developments from the field of renewable raw materials in combination with bio-based resin systems: In the “Gro-Coce” project, an innovative ceiling system was developed by combining sustainable building products and methods. Currently, a high-performance hemp-based semi-finished product as well as the steps for its reproducible production by means of textile surface formation is developed by the research team. Initial application and load tests of the hemp-based semi-finished products on wooden beams confirmed the high performance potential of the natural fibre materials.

Special functional textiles are based on composite materials with coatings or membranes. The previous production of the coatings/membranes poses ecological and health risks. At STFI, solvent-free, purely aqueous coating systems and a technology for their application were therefore developed for the protective textile sector, resulting in a breathable, waterproof and wash-resistant textile coating.

The central highlight of the STFI's presence at the fair is a mobile robot system, which demonstrates the automated loading of a small-scale bobbin creel. At the STFI, the robot is part of the “textile factory of the future”, where a play mat is woven and processed step by step along the textile chain.

Each year, since its creation more than 20 years ago, the JEC Composites Innovation Awards celebrate successful projects and cooperation between players of the composites industry. The competition has especially shined a light on some 203 companies and 499 partners, awarding them for the excellence of their composite innovations.

The ceremony took place on April 26th in Paris. Highlighted by the presence of jury members, finalists and winners but most importantly, as it was livestreamed, the gathering of many people all around the world to watch the awaited results.

The enthusiasm for the Innovation Awards, exactly 7 days prior to JEC World, is a good sign of the industry’s eagerness to get back together and ensure the future of composites innovation.

• Aerospace Application
  Diab (Sweden): 100% thermoplastic panel for cabin interiors
• Aerospace – Process
  MTorres Disenos Industriales S.A.U. (Spain): Innovative Infusion Airframe Manufacturing System
• Automotive & road transportation – Structural
  Jaguar Land Rover Limited (UK): TUCANA
• Automotive & road transportation – Surfaces
  AUDI AG (Germany): Seamless Integration of Flexible Solar Film in FRP
• Building & Civil Engineering
  Windesheim (Netherlands): Structural Re-Use of Thermoset Composites
• Design, Furniture and Home
  Kairos (France): Kairlin®, a new recyclable & compostable material
• Equipment and Machinery
  Fibraworks GmbH (Germany): Winding the future – fibraforce technology
• Maritime Transportation & Shipbuilding
  Voith Composites SE & Co. KG (Germany): Marine Rotor Blades made of Voith ‘Carbon4Stack’
• Renewable Energy
  Siemens Gamesa Renewable Energy (Denmark): RecyclableBlade
• Sports, Leisure & Recreation
  Bcomp Ltd. (Switzerland): Eco-joint from thermoset race and thermoplast road

• INDA, the Association of the Nonwoven Fabrics Industry, today announced six new board members and its 2022 slate of officers to guide the success of the nonwovens industry and its members.

Elected by the INDA membership to three-year terms that began on March 1, the new board members bring a high level of diverse expertise and insight to the management of the association as it moves forward with its vibrant growth.

“I am delighted to welcome such a strong group of new board members who bring deep industry knowledge and insights to provide strategic stewardship for our association,” said Dave Rousse, INDA President. “We look forward to working with them to advance INDA’s new value proposition to enhance our industry’s leadership position and deliver greater value to our members.”

The new board members are from global leaders Lenzing Group, Bast Fibre Technologies, Reifenhauser Reicofil, Rockline Industries, Hollingsworth & Vose Company and Principle Business Enterprises.  

INDA also announced Bryan Haynes, Ph.D., R&E Technical Director Kimberly-Clark, has been named Chairman of the Board. Barbara Lawless, Vice President Sales and Marketing, Medical Products, Precision Fabrics Group, Inc. has been elected Vice Chair of Finance, and Richard Altice, President and CEO of NatureWorks, has been appointed to INDA’s Executive Committee.

The new board members are:

• Jürgen Eizinger, Senior Commercial Director, Nonwovens Business EU/AM/MEA, Lenzing Group

Eizinger has nearly 20 years of fiber industry experience. He has been with the Lenzing Group since 2001 and most recently was Vice President of the Global Nonwoven Business. He has worked at multiple locations around the world and held various commercial, engineering and technical customer services roles.

• Jim Posa, President and General Manager, Bast Fibre Technologies, Inc.

Posa has 30-plus years of nonwovens experience and has successfully led businesses from startups to some of the largest companies in the nonwovens market. He has developed and implemented strategic business, development, operational and acquisition growth plans. His teams have worked with businesses focused on most of the major end use markets such as hygiene, wipes, filtration, medical and industrial. As a senior executive, Posa has led global businesses at Fiberweb, BP/Amoco, CEO of a Nisseki/Amoco joint venture (ANCI), Lydall, and Nitto America. A long-time INDA supporter, he has previously served on committees and as a Board member.

• Markus Mueller – Sales Director and Board Member, Reifenhauser Reicofil

Mueller brings to the INDA Board 35 years of experience with Reifenhauser in the nonwovens and film industries. His experience has included roles as PLC Engineer, Commissioning Engineer, Project Manager and Sales Manager. Mueller has extensive knowledge of the global hygiene and medical nonwovens markets. He holds a degree in Electrical Engineering from the Technical University of Cologne.

• Matt Koele, Director of Global Materials Development, Rockline Industries

Koele is based at Rockline’s headquarters in Sheboygan, WI.  Before joining Rockline in 2012, he has held several business and Research and Development (R&D) leadership positions at SC Johnson and Kimberly-Clark Corporation. An inventor with over 10 patents, Koele is a magna cum laude graduate of Michigan Technological University in Chemical Engineering.

• Mike Clark, President, Filtration Solutions, Hollingsworth & Vose Company

Clark joined H&V in 2003 and has held numerous leadership positions in the U.S. and Germany. He previously served as the President of the High Efficiency and Specialty Filtration Division from 2009 to 2020.  Before joining H&V, Clark was a strategy consultant for eight years working with Fortune 100 manufacturing companies. He holds a bachelor’s in Mechanical Engineering from Rensselaer Polytechnic Institute.

• Andrew Stocking, Ph.D., President and CEO, Principle Business Enterprises, Inc. (PBE)

Stocking joined PBE in 2017 after a career in engineering, technology, nonprofits and government. He was named President and COO in 2018, then President and CEO in 2020, becoming the third-generation leader of the family-owned organization. He previously held roles in the private sector and within federal government offices, including the Department of Energy and Congressional Budget Office. He earned a BS in Chemical Engineering and an MS in Civil Engineering from Stanford University, and a Ph.D. in Resource Economics from the University of Maryland.

The 21-member board is comprised of elected Board Officers. One-third of the entire Board is elected each year for a three-year term by a majority vote of INDA’s general membership. INDA’s Executive Committee, empowered to act on behalf of the Board between meetings, consists of the Board Officers plus four appointees.

• The 16th World Pultrusion Conference will be postponed to 5-6 May 2022

The EPTA – European Pultrusion Technology Association in cooperation with the American Composites Manufacturers Association (ACMA) will postpone the 16th World Pultrusion Conference to 5-6 May 2022 due to the corona situation and the postponement of the JEC World, with which there is a close partnership.

This conference takes place every two years and is the meeting point of the European and worldwide Pultrusion Industry. More than 25 international speakers from Belgium, Germany, France, Spain, The Netherlands, Turkey, UK and the USA will present practical presentations about innovative applications, technologies and processes. Equally current market trends and developments are on the agenda.
This World Pultrusion Conference takes now place on 5-6 May 2022 in Paris, France. The presentation language will be English. The program, further details and registration information is available at www.pultruders.com.

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

Category “Research and Science”
First place in the “Research and Science” category was awarded to the German Aerospace Center (DLR) for its Bondline Control Technology (BCT). This innovative process is used for quality control and assurance of bonded joints. The core element is a porous fabric which is applied to a joining surface using an epoxy adhesive or matrix resin. Peeling away the fabric creates a chemically reactive and undercut surface and can also be used as a test to check adhesion to the substrate. BCT has potential in a variety of possible applications. For example, peel ply can be replaced by BCT fabric to produce composite components with an optimised joining surface. The cost-effective BCT peel test is suitable for coupon testing and process control. In addition, the combined adhesion test and surface pre-treatment can be used for quality assurance of bonded repairs on fibre composite structures.

Second place was taken by the Institute of Textile Technology (ITA) at RWTH Aachen University and its partners AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR with “StoneBlade – Lightweight construction with granite for the wind industry”. This innovation enables manufacturers to reduce the amount of non-recyclable materials used in rotor blade construction. At the same time, it reduces the weight of these components and improves the mechanical properties relating to the stability of wind turbines. The innovative approach replaces glass-fibre reinforced plastic in the blade components with hard rock – a natural, cost-effective and recyclable lightweight material. The slabs of rock are cut and ground to a thickness of just a few millimetres and embedded in a fibre composite laminate with carbon fibre, which stabilises them for alternating load cases. The pre-stressed material is pressure-stable in the composite and can absorb tensile forces in the event of continuously alternating loads without any loss of stiffness.

Third place went to the Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK) with its partner Mercedes Benz AG for the interdisciplinary development of a highly integrated inductive charging module for electric vehicles. The ultra-thin charging module was designed to make optimum use of space in the vehicle underbody without reducing ground clearance. An interdisciplinary approach was adopted for the development process. This involved the electrical, mechanical and process characterisation of high-frequency Litz wires, ferromagnetic foil and metal wire cloth as well as the creation of a simulation model. The result is a demonstrator for a charging system with a structural height of 15 mm and a total weight of 8 kg. It achieves a transmission efficiency of up to 92 percent at 7.2 kW nominal power and active air cooling. The hardware demonstrator was fabricated in a 3-step process using RTM and VARI techniques.

Overview of all the winners in the three categories:
Category “Innovative Products/Applications”
1st Place: “Traffic signs from Nabasco (N-BMC)” – Nabasco Products BV and Lorenz Kunststofftechnik GmbH, partners: Pol Heteren BV and NPSP BV
2nd Place: “Novel, ultratough vinyl ester resin for the construction of large marine vessels” Evonik Operations GmbH
3rd Place: “Air intake housing with a multi-material design for gas turbines” – MAN Energy Solutions SE, Leichtbau-Zentrum Sachsen GmbH and Leichtbau-Systemtechnologien KORROPOL GmbH.
Category “Innovative Processes”
1st Place: “In-mould wrapping” off-tool, film-coated, fibre composite components for exterior applications – BMW Group, Partner: Renolit SE
2nd Place: “Adaptive automated repair of composite structural components in the aviation sector” – Lufthansa Technik AG, Partner: iSAM AG
3rd Place: “Automated surface pre-treatment using VUV excimer lamps” – CTC GmbH
Category “Research and Science”
1st Place: “Bondline Control Technology (BCT)” – German Aerospace Center (DLR)
2nd Place: “StoneBlade – Lightweight construction with granite for the wind industry” – Institute of Textile Technology at RWTH Aachen University, Partners: AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR
3rd Place: “Interdisciplinary development of a highly integrated inductive charging module for electric vehicles” – Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK), Partner: Mercedes Benz AG

Submissions for the next Innovation Award can be made from the end of January 2022.

Penn Textile Solutions GmbH is one of the world's leading manufacturers of elastic fabrics for under-wear, corsetry, sportswear and swimwear, as well as highly functional textiles for technical applications. The fully integrated company with its own warping, circular knitting, warp knitting, dyeing and finishing facilities currently employs around 150 people.

Penn has long relied on Mahlo
Penn has relied on the cooperation with Mahlo for years. The manufacturer of measuring, control and automation systems for web-shaped goods has decades of experience in the field of process control. Until the summer of 2020, the textile manufacturer had been using a basis weight measurement system in the stenter frame outlet with beta radiation and manual control. "When the krypton preparations had passed their half-life, we had to make a decision: Exchange or replace the system right away", says operations manager Franz Schütte. They sat down with Mahlo representatives and looked for the best solution. Since the systems had already reached a high operating age and the measurement was limited to the basis weight, a new concept was decided upon. "Mahlo made us the best price-performance offer." The new system should be even more efficient and easier to operate for the special makes..

The compression zones of the functional fabric create corresponding distortions within the textile surface in its raw state, which have to be smoothed out in the fixing process. This work is now taken over by a process control system. The Mahlo Famacont PMC-15 with two measuring points automatically controls the leading of the stenter frame by continuously and contactlessly determining the mesh density. In addition, the Patcontrol PCS-20 process control system ensures that the dimensions of the different zones are recorded and also automatically controlled. "The previous beta-radiation facility was not able to collect this kind of data," explains the Penn operations manager. Another important aspect for the textile manufacturer: the complete and costly radiation protection is no longer necessary with the new systems.

Despite very good experience with Mahlo in the past, every change naturally involves a risk. Penn did not have to rely on theoretical considerations, however, but carried out tests in advance with appropriate sample material in the Mahlo test laboratory. The results convinced the decision-makers.

MS Plastic Welders, LLC, a leader in ultrasonic technology, announced today that it has changed its name to MS Ultrasonic Technology, LLC. This aligns the name with the sister companies worldwide as well as with the brand name MS Ultrasonic Technology Group.  

The name change reflects the growth of the company as well as its vision for the future.

COO, Peter Wall said “The new name really speaks to who we are as a company. Considering our current relocation to Howell, MI, it was the perfect opportunity to implement the name change at the same time.”

“We’re very excited about the name change as it fits perfectly with our slogan- We Are Ultrasonics.,” said MS Ultrasonic Technology, LLC CFO, Rouven Muell. “It makes it easier for customers, partners, and candidates to consistently recognize our company within the MS Ultrasonic Technology Group and clearly addresses our focus in Ultrasonics.”

Devan Chemicals has been supporting high performance sport in the UK and Belgium with its ‘cool comfort technology’ Moov&Cool.

Worldwide, hot temperatures are a new reality that brings extra challenges for athletes. Thermoregulation technology is becoming more and more important in order for athletes to perform at their best on the pinnacle of sports.

Working alongside the English Institute for Sport (EIS) and Sally Cowan Ltd, the technology is being applied to garments with the aim of improving the thermal comfort of elite athletes.

Moov&Cool consists of a multi-functional polymer technology that proposes to absorb heat during performance and improve the moisture management properties of the fabric. The treatment has been designed to simultaneously react to sweat build up and heat emission.

In Belgium, Devan has been involved in the Gold2Gold project carried out by Sport Vlaanderen. Gold2Gold is a unique collaboration between sports, government and the industry to prepare Belgian athletes to perform better in hot environments during world-level championships. Thermoregulating technology is increasingly becoming a key aspect of endurance performance for elite athletes. At that top level, small differences in body core temperature can make the difference between being on the podium or sometimes not even finishing the race.

Hexcel, a global leader in advanced composites technologies, announces the successful maiden flight of a lightweight camera drone, developed using Hexcel HexPly® carbon fiber prepregs. The composite drone was developed by a team of students from the University of Applied Sciences Upper Austria in Wels with composite materials supplied by Hexcel Neumarkt in Austria.

A team of six students in the university’s lightweight construction and composite materials course was responsible for the complete design, engineering, and manufacture of the camera drone over a period of 18 months. Hexcel materials and optimization of the composite engineering enabled the team to reduce the composite structural mass by an impressive 42% compared to similar drones.

Hexcel Neumarkt was one of eight industrial partners supporting the university team throughout the project, providing all carbon fiber prepreg materials used for the drone’s landing gear as well as the fuselage. The ultra-lightweight 32g landing gear was laid up and cured in the press, whereas the fuselage was autoclave cured by the student team using Hexcel HexPly M901 and HexPly M78.1 prepreg resin systems with a combination of woven and unidirectional carbon fiber reinforcements.

With the development of Unmanned Aerial Vehicles (UAV) as a key emerging market and innovation space in the transportation sector, Hexcel’s collaboration with the University of Applied Sciences Upper Austria team not only creates an important link with the next generation of lightweight composite engineers but also highlights the weight saving and structural benefits of Hexcel composite material solutions.

"The massive weight saving achieved with their updated version of the camera drone is a fantastic achievement by the student team," said Michael Rabl, Dean of FH Wels of the Upper Austria University of Applied Sciences. "The joint study not only illustrates the wide range of complex and innovative composite techniques present in the drone sector but also presents the opportunities that exist for further development in the wider Urban Air Mobility (UAM) and aerospace composites markets.”

Hexcel congratulates the project team which includes Lukas Weninger, Karl-Heinz Schneider, Jakob Schlosser, Matthias Thon, Marla Unter, and Simone Hartl on an exceptional piece of lightweight composite design and thanks them for showcasing the contribution of Hexcel materials with a presentation and drone flight. Johanna Arndt, research and technology group leader at Hexcel Neumarkt, said, “It was a great pleasure to work with the team who were very cooperative and self-motivated to succeed. Watching the drone just fly around the Neumarkt plant was just great.”

Hexcel manufactures a complete range of carbon fibers, dry carbon UD tapes, specialty reinforcements, prepregs, and honeycomb core materials, providing customized manufacturing options for new UAM applications that combine aerospace reliability with the high-rate production required. Hexcel composite materials are the ideal solution for the lightest and most efficient cost-competitive transportation vehicles of the future.

AMAC cooperates with ITA (Institute for Textile Technology of RWTH Aachen University and their ITA GmbH) for the business development in composites 

As of April 19th, 2021, AMAC is pleased to announce its cooperation with the Institute for Textile Technology, ITA, of RWTH Aachen University and their ITA GmbH. The aim of the cooperation is to strengthen and develop their business activities in composites.

ITA, as one of the largest institutes on the campus of the excellence University RWTH Aachen, Germany, develops complete solutions from the manufacturing of the fiber itself over the processing of textile intermediates with thermoplastic and thermoset resins, textile-based part manufacturing, capabilities such as braiding, pultrusion and in-situ impregnation of textile preforms. Top 3 focused industries are transportation and particularly the e-mobility sector, building and construction as well as the wind energy sector. Additionally, ITA GmbH is the partner of the industry in R&D, focusing on 8 business segments, providing technology and knowledge transfer, as well as offering comprehensive solutions along the entire textile value chain.

Prof. Dr. Thomas Gries, Director of ITA, explains the background of the strategic cooperation with focus on composites: „Our long-term experience and unmatched know-how with all aspects of continuous fibers, non-wovens and web-based reinforcements allows us to deliver to the composite manufacturers a complete technology and service offer around the development of technical textiles, from the development of glass and carbon fibers to the textile-based processing of composite parts. In all process steps of our research and developments, we focus on sustainable and recyclable solutions, an efficient cost-performance ratio, the possible use of bio-based materials and the reduction of the CO2 footprint. We are glad to cooperate with Dr. Michael Effing and AMAC in order to benefit from his door-opening network in the composites industry. “

Dr. Michael Effing, Managing Director of AMAC GmbH: „I am very happy to support the ITA to generate innovation thanks to further industrial networking and pre-competitive joint projects. ITA is indeed a one-stop source for composite solutions from the fiber to the cost-efficient manufacturing of final parts. In the context of the Covid-19 impact to the entire industry, it makes sense to bundle forces. Furthermore, ITA, with its long tradition and satisfied customers offers further valuable networking opportunities to the composites industry as well as access to relevant complementary fiber-based excellence and 250 different technologies in their machine-park with an outstanding infrastructure in Aachen.”