From the Sector

The Management Board of the European Chemicals Agency has selected Dr Sharon McGuinness as ECHA’s next Executive Director. As part of the appointment procedure, she will make a statement before the European Parliament and answer questions from its members. This is tentatively scheduled for 4 July 2022.

Dr Sharon McGuinness, an Irish national, is the Chief Executive Officer of the Health and Safety Authority (HSA) in Ireland since 2018. Prior to this, she was the Assistant Chief Executive for the Chemicals and Prevention Division within the Authority, with responsibility for division management, policy provision, advice and enforcement for a wide range of occupational health and safety, chemical and market surveillance legislation aimed at protecting human health and safety for workers and consumers.

She was a member of ECHA’s Management Board between 2014-2020 and Chair of the Board between 2016-2020. She graduated from the University College Dublin with a B.Sc. (Hons) in pharmacology and chemistry, and she holds a PhD in pharmacology, as well as diplomas in Legal Studies and Company Direction.

Dr McGuinness was one of the candidates preselected by the European Commission after an open competition and interviewed by the Management Board for the post.

Her selection follows that of Bjorn Hansen who retired in March 2022. Since 1 April 2022, Shay O’Malley has been ECHA’s acting Executive Director.

The term of office of the Executive Director is five years. It may be prolonged by the Management Board once, for a further term of five years.

Textile Groups Urge U.S. to Maintain Penalty Tariffs on Finished Products

The Biden administration should maintain Section 301 penalty tariffs on finished textiles and apparel or risk reversing once-in-a-lifetime nearshoring trends and undermining critical investments and jobs in the U.S. and Western Hemisphere, three key American textile manufacturing groups said today.

In a formal submission to the U.S. Trade Representative’s (USTR) office, which is conducting a four-year statutory review of the tariffs, the associations expressed strong support for the continuation of penalty tariffs on imports from China and warned of the consequences associated with removing the tariffs.

“A key aspect of [the Biden administration’s trade] policy is the need to maintain Section 301 tariffs, absent substantive improvements in China’s pervasive, predatory trade practices,” the groups said. Lifting the tariffs “would also do nothing to achieve the administration’s goal of easing inflationary pressures, as apparel prices out of China continue to hit rock bottom even with the Section 301 tariffs,” they noted.

The submission was filed by the National Council of Textile Organizations (NCTO) and the Narrow Fabrics Institute (NFI) and Industrial Fabrics Institute (USIFI) – both divisions of the Advanced Textiles Association (ATA).  The associations represent the entirety of the U.S. textile production chain.

“For decades, China’s illegal actions have undermined virtually every domestic manufacturing sector and contributed to the direct loss of millions of U.S. jobs. These devastating state-sponsored practices include intellectual property theft as well as pervasive state-ownership of manufacturing, industrial subsidies, and abhorrent labor and human rights abuses in the Xinjiang region,” they noted. “Cancelling these tariffs would create further unhealthy dependence on Chinese supply chains and embolden future systematic trade abuses as bad actors know that the U.S. will not hold them accountable.”

The tariffs were imposed on China beginning in 2018 in response to China’s continuing IP and related trade violations. China has since failed to comply with an agreement it reached with the United States in 2020.

The Board of Directors at INDA, Association of the Nonwoven Fabrics Industry, elevated Tony Fragnito from Chief Operating Officer of INDA to President of INDA effective May 31. Fragnito will assume the position currently held by Dave Rousse, who will become President Emeritus and provide support and assistance to Fragnito as needed until Rousse fully retires in January, 2023.

Fragnito joined INDA November 29, 2021 as Chief Operating Officer and has been leading INDA’s implementation of its new Strategic Plan, as well as updating INDA’s technology platform. This follows decades of leadership experience assisting trade and professional organizations in realizing their organizational and operational potential. A certified public accountant, Fragnito brings strong financial acumen in addition to extensive information technology, human resource and program management accomplishments from organizations representing a variety of professions and industries.  

Premium Group and JOOR have renewed their partnership to power the SS23 PREMIUM and SEEK trade shows through JOOR’s digital platform, underpinning their belief in the power of a hybrid approach to wholesale.

From 7 - 9 July, buyers visiting the shows in Berlin will be able to learn more about and shop from exhibitors in a new hybrid way. Buyers can discover the full PREMIUM and SEEK portfolio of brands both in-person and online 24/7 by visiting JOOR Passport, JOOR's digital trade show destination.

Premium Group unites its various show locations to one cosmos for SS23 at Messe Berlin. The PREMIUM and SEEK shows will be joined by two further components— The Ground is a D2C creative platform for brands and consumers to meet, connect, and collaborate through one-of-a-kind experiences, engaging content, and innovative products, while FASHIONTECH, features masterclasses and panel discussions from the fashion industry’s most brilliant minds. A calendar of content includes deep dives into strong, successful, and sustainable strategies. As part of the content offer, JOOR will facilitate a masterclass on ‘Digital Wholesale’ and a future-looking roundtable discussion with four leading fashion brands on the FASHIONTECH stage.

Throughout the duration of the show, in-person buyers and visitors will have the ability to shop via the Premium Group mobile app. By simply scanning a brand’s corresponding QR code, visitors will link to the brand’s custom profile on JOOR Passport and be able to shop collections directly on the platform. JOOR Passport will also extend the duration of the shows by up to three months, allowing brands to continue wholesale selling digitally outside the window of the physical show.

JOOR and Premium Group’s flexible hybrid format allows visitors and brands a seamless digital and physical introduction to each other and their collections, the opportunity to connect in an efficient, effective, and longer term way, and the convenience to shop the show 24 hours a day from anywhere in the world.

Brands participating include Drykorn, Closed, Bertoni of Denmark, Veja, Ecoalf, Wrangler and Absolut Cashmere.

Setting concrete environmental sustainability objectives for abating direct greenhouse gas emissions and leveraging investments and state-of-the-art technology. This is the approach that has always guided RadiciGroup in operating its businesses with a wide range of products: chemical intermediates, polyamide polymers, high performance engineering polymers and advanced textile solutions.

Between 2011 and 2020, overall Group greenhouse gas emissions were cut by 70%, falling from about 700,000 metric tons per year of CO₂ equivalent to 200,000 metric tons.  

These results were largely achieved through the action implemented by the Group’s Specialty Chemicals Business Area at its plants in Novara, Italy, and in Germany, which are the heart of RadiciGroup’s chemicals business. Here the Group produces an essential intermediate for synthesizing polyamide 66, adipic acid, whose production process releases nitrous oxide as a by-product. Nitrous oxide in itself is not particularly problematic (in fact, it is used in the medical sector as an anaesthetic and in the food industry as a spray propellant, in cans of whipped cream, for instance), but, if it is released into the atmosphere, it has a much higher greenhouse gas effect than carbon dioxide.

At the Radici Chimica site in Novara, a multiyear investment budget of over EUR 10 million was dedicated to lowering these emissions through three important undertakings: in 2004, putting into operation a three catalyst bed reactor, designed and patented by the company, to decompose nitrous oxide into nitrogen and oxygen, the two elements it is composed of, thus making it innocuous for the atmosphere; in 2013, installing an EnviNOx plant to decrease the release of nitrous oxide formed in the production of nitric acid, and, in 2021, a further improvement in the emissions abatement system associated with nitric acid production.

Since activating the last plant just 9 months ago, more than 35,000 metric tons of CO₂ equivalent have been cut. All the above-mentioned actions have enabled Radici Chimica Novara to record a nitrous oxide emissions level less than 10 ppm, a value close to zero.

Focus on eccentric screw pumps and pumps for shear-sensitive materials

Improved productivity and increased lifespan and tailored solutions also for the most demanding applications within the chemicals and plastics industries and in PUR applications – these are the convincing arguments with which Oerlikon Barmag is showcasing its precision metering pumps at this year’s ACHEMA between August 22 and 26, 2022 in Frankfurt. The focus is on the new pump for shear-sensitive conveying media and the new eccentric screw pump.

Eccentric screw pumps – robust all-rounders convey any medium
The requirements for pumps are considerable, as the demand for customized solutions for increasingly complex processes is rising. This is particularly true for Oerlikon Barmag’s new eccentric screw pump range. High wear-resistance, increased durability and robust operation – the new pump is tailor-made for conveying highly-filled, high-viscosity and abrasive media, such as filled adhesives, filled silicones and filled casting compounds, for example. The is the multi-stage seal system, which considerably increases the pump’s lifespan. The upstream shaft sealing ring protects the slide ring seal against excessively-fast wear caused by challenging media. In turn, the optimum alignment of the drive shaft – ball bearing-supported and centrally-guided through the shaft sealing ring – prevents any metal debris caused by friction and hence ensures considerably greater durability. Producers benefit from considerably greater productivity, as the pumps’ maintenance intervals and hence machine downtimes are significantly reduced.

New pump for shear-sensitive materials
For increasingly complex customer-specific process solutions, Oerlikon Barmag is now expanding its GA series, developed especially for the challenging conveying of high-viscosity media, to include the GAB51F for shear-sensitive conveying media. The newly-developed pump with its viscosity range of max. 300 Pas is tailored to conveying high-viscosity, shear-sensitive materials such as adhesives and silicones, for example. “The shear forces impacting the medium within the pump are reduced to a minimum as a result of a specially geometry”, explains Thorsten Wagener, Senior Sales Manager within the Pump Construction business unit. The material is conveyed through the pump in an as gentle and low-pulsation manner as possible and metered precisely at the outlet – ensuring it retains its characteristic properties.

High-speed metering pump with sealed product space
The high-speed metering pump has been especially developed for metering poorly-lubricating media. Here, the main benefit is the sealed product space, which extends the pump’s lifespan considerably. The space that comes into contact with the media is limited to the area around the gears. “As a result, the high-speed pump is particularly suited for applications in the chemicals industry, which frequently involve aggressive acids”, comments Thorsten Wagener.

GM series for low-viscosity media
The pumps in the GM and GA series provide precision metering with low-pulsation feeding of the conveying medium. The multi-stage GM pump conveys low-viscosity media (i.e. 250 bar, 100 mPas) even under high pressure and in the most challenging conditions. The square design from the proven GM series is the standard pump for many metering tasks. The development of the multi-stage pump expands the applications range for the GM series considerably. The round 2-stage GM pump has been developed especially for use in high-pressure technology. It masters the particular challenge of conveying small throughputs with low viscosities. The pump is perfect for 0.05 through 20 cm³/rev feed sizes and is excellently suited for use in high-pressure machines for PUR molded parts, foam slab stock, refrigeration unit insulations and sandwich panels, for example.

GA series pumps for high-viscosity media
The Oerlikon Barmag GA range has been especially developed for the challenging conveying of media with higher viscosities. The GA series pumps are available for conveying volumes of between 1.25 and -30 cm³/rev (0.6-144 l/h). They have been designed for pressures of up to 200 bar, for viscosities of up to 1.500 Pas as well as for temperatures of up to max. 225 °C. With this range of pumps, Oerlikon Barmag offers its customers tailor-made solutions for many technical processes in which high-precision and even metering is of paramount importance.

The drum pump – conveying and metering using a single unit
With the drum pump, the Oerlikon Barmag pump specialists have created a pump designed specifically for conveying and metering high-viscosity materials such as adhesives, silicones and other high-viscosity materials from drums and other large containers and for pressures of up to 250 bar. Its special features not only include the fact that it removes high-viscosity materials from the drum, but that it also meters the medium directly without any additional interim stops.

Carbios announces the appointment of two new members to its Executive Committee: Lionel Arras, Industrial Development Director, and Mathieu Berthoud, Sourcing and Public Affairs Director.

Lionel Arras joined Carbios’ teams in 2021 to support the industrial growth of PET enzymatic recycling technology as Industrial Development Director. He was appointed to the Company’s Executive Committee on May 2. An engineer who graduated from ENSIC Nancy and holds an MBA from the Lyon School of Management, Lionel Arras has more than 25 years of experience in the field of process engineering and the chemical industry.
At Carbios, he now heads a team of around 50 people mobilized around three major divisions:
- the industrial demonstration plant, inaugurated last September in Clermont-Ferrand,
- technological development,
- the first Reference Unit project, installed on the Indorama Ventures site in Longlaville, Meurthe-et-Moselle, France.

Lionel Arras, Carbios’ Industrial Development Director: “After the successful start-up of our industrial demonstration plant in Clermont-Ferrand, we are continuing our scale-up with the construction of the first enzymatic recycling plant in the world in Longlaville, France. Its launch, scheduled for early 2025, will enable the processing of 50,000 tons of post-consumer PET waste or the equivalent of 2 billion bottles. It is a great source of pride for me to be able to support Carbios in this strategic development phase.”

Mathieu Berthoud will join Carbios as Sourcing and Public Affairs Director on June 1, 2022. With more than 30 years of experience, including 10 years at Rhodia (now Solvay) and more than 20 years at Suez, in various commercial development or subsidiary management positions, he was most recently Technical and Performance Director for the Group’s recycling and recovery activities. A university-trained scientist, he also holds an MBA from HEC Paris. At Carbios, he will be responsible for securing the supply of PET waste for the future reference plant in Longlaville and the other industrial sites that will follow. He will also manage the Company’s public affairs.

International textile producers meet again in Istanbul, Turkey, from June 14 – 18, 2022 on the occasion of the ITM + Hightex Exhibition. In Hall 9 (Hightex) the exhibitors will present the complete industry value chain from nonwovens raw materials, production machines and accessories to the endproduct. The related industries covered include hygiene, filtration, fabrics and apparel, medical, automotive, wipes, home furnishings and upholstery. DiloGroup offers tailor-made production systems from one supplier and will inform about its portfolio and the latest equipment developments from fibre opening to the finished felt.

DiloGroup will inform about complete lines as well as high speed needlelooms for spunbonds. A new, simplified elliptical needle beam drive makes Hyperpunch technology also attractive for standard application. Hyperpunch HαV allows a more uniform stitch distribution in the preneedling process especially in combination with the new needle pattern 6000X. In a complete needling line this felt homogenization process can be improved further. The new needle pattern 8000X is a milestone in the needle pattern development process and results in endproduct surfaces with low markings over a wide range of advances/stroke.

Another strong pillar of the sales program over decades has been fibre preparation and high speed webforming equipment for other nonwoven technologies. The further development of the high-speed layering principle “Hyperlayer” made progress for better CD strength through a combination of inline cards and crossline card with crosslapper. Particularly, carding machines in a working width above 3.5 m up to 5.1 m have been supplied by DiloSpinnbau as complete high speed carding systems, comprising two or even three cards in a line to directly feed the hydroentangling units of various suppliers. Together with DiloTemafa not only have high throughput rates been achieved in the fibre preparation section of the line but also dedusting filtering and air-conditioning systems have been successfully engineered and integrated.

Together with Sicam, Dilo has combined know-how for hydroentangling technology and therefore can provide complete lines as general contractor including equipment for cutting, winding and packaging.

Another interesting machine is the 3D-Lofter, first presented during ITMA 2019 in Barcelona, which offers a wider range of nonwovens applications by exploring the third dimension. A series of single web forming units which work according to the aerodynamic web forming principle deliver defined fibre masses in varied patterns on a base needlefelt. A stress oriented production of technical formed parts resulting in fibre savings or patterned DI-LOUR or DI-LOOP felts with or without repeat are two examples for this technology which explores new application areas for needlefelts.
The 3D-Lofter technology may also be used “inverted” as “IsoFeed” for filling up bad spots in web mats and thus achieves a better homogeneity of spunlace or airlay products.

The DiloLine 4.0 concept offer I4.0 modules which not only support the user but also facilitate quality control and maintenance by a maximum data transparency in production and control of operation. The Dilo solutions “Smart Start” for a fully automatic start of the production line or “DI-LOWATT” for energy savings are accompanied by Siemens solutions which can be selected via App or Data Cloud “MindSphere”.

EURATEX has just released its Spring report, offering a detailed insight into trade figures for the European textile and apparel industry in 2021. The numbers are encouraging: comparing with the dramatic corona-year 2020, EU exports of textile and clothing articles increased by +10.6%, while imports dipped by -7.5%. As a result, the EU trade deficit improved, even it remains significant (- €48 billion).

Furthermore, import prices went slightly down in clothing and dropped in textiles, following a strong decrease of Chinese import prices of face masks and protective medical supplies.

The boost in exports was mainly due to strong performance on the Swiss, Chinese and US markets. On the other side, EU sales of textile & clothing to the United Kingdom fell sharply (-23%), due to Brexit new requirements, customs’ delays and shortage of truck drivers.  Imports from the EU top supplier, China, plunged by -28%, corresponding to €13 billion. Similarly, textile and clothing imports from the United Kingdom recorded a sharp decrease over the period (-48%, equal to €-3 billion).

Director General Dirk Vantyghem commented: “the 2021 export figures, presented in this Spring report, confirm that EURATEX members have gained momentum; even if energy prices are causing some serious short-term disruptions, our long-term ambition remains to be a world leader on sustainable textiles.”

The international trade dimension is indeed critical for the competitiveness of the European textile ecosystem, and needs to be fully embedded in the EU’s Strategy for Sustainable and Circular Textiles. The Commission insists that “all textile products placed on the EU market, are durable, free of hazardous substances, produced respecting social standards…” This is an essential condition to create a level playing field between all textile and apparel companies, regardless of their production base. With €100 billion of imports, and over 20 billion of “foreign” textile items put on the Single Market, this requires a dramatic upscaling of market surveillance, without however disrupting fluid supply chains.

Looking at the impact of war in Ukraine, EURATEX has strongly condemned the Russian aggression, and offered support to the Ukrainian textile industry. Ukraine offers valuable sourcing opportunities for European textile and apparel brands, as part of a broader nearshoring trend, which seems to emerge from the trade figures.

• Featured at FESPA Global Print Expo 2022, new cloud and mobile suite offerings help reduce costs and maximise the value of customers’ EFI printer investments

Electronics For Imaging, Inc. announced the availability of its EFI IQ™ suite of cloud and mobile applications with supported EFI VUTEk®, Wide Format, and Nozomi inkjet printers. With this cloud service, EFI™ printer users can monitor production and printer utilisation, including exact device-level consumable tracking data, to reduce downtime, reduce costs and maximise the value of their EFI printer investments. New EFI wide- and superwide-format UV LED printers will include a one-year subscription to EFI IQ. EFI inkjet printer users can also purchase IQ subscriptions for other supported printers.
 
The newly available cloud service for superwide-format production is making its debut at the 31 May - 03 June FESPA Global Print Expo in Berlin.

User-friendly with better business intelligence
According to an early user of the cloud service’s new inkjet offering – Dave Brewer, chief technology officer of California-based Image Options – “EFI IQ is a user-friendly tool that gives me better business intelligence to make better decisions.”
 
By monitoring their printer fleets in real time, EFI IQ users can reduce consumable spend, save on labour costs, improve margins, and more.

Productivity with powerful cloud tools
The decision to adopt EFI IQ comes down to several key questions owners and managers should ask themselves about business performance, including:

• Can you accurately measure ink usage?
• Is your team able to get real-time production blocking alerts?
• Are you able to compare performance metrics between printers and shifts?
• Are you able to check production status from anywhere, at any time?

The IQ suite is a management solution which has a direct connection to EFI printer data, and it gives business leaders powerful tools to handle their day-to-day production and administrative challenges. Plus, the suite’s EFI Go component helps to ensure that managers receive urgent updates wherever they are. At early user site Studio DAR in Bielsko-Biała, Poland, notifications from the mobile application allow managers and operators to keep the company’s EFI Pro 32r+ roll-to-roll printer running as much as possible.