From the Sector

Hexcel is collaborating with NaCa Systems, a Tier 1 supplier of natural fiber composite automotive interior parts, on the development of a lightweight carbon fiber prepreg and wood fiber composite sportscar seat back using a rapid press molding process. This innovation validates a short cycle time production process for CFRP and wood fiber composite parts and offers a host of benefits to automotive manufacturers.

Hexcel supplies NaCa Systems with an optimized version of its HexPly® M77CS epoxy prepreg material. HexPly® M77CS is a fast curing hotmelt, thermosetting epoxy matrix, specifically designed for prepreg applications for which short cure cycles and clear surfaces with perfect aesthetics are required.

The lightweight seat back demonstrates a 40% weight saving compared to a typical injection molded plastic component whilst also featuring a significantly improved CO2 footprint vs a full carbon part. The prepreg and wood fiber structure doesn’t produce sharp edged pieces when damaged. In addition, wood fiber composites also increase sound absorption, contributing to improved NVH damping within the vehicle interior.

The NaCa Systems seat back will be on display on the Hexcel stand at JEC World 2020.

• Series order for a total of 500 units
• First SGL Carbon component project for manned autonomous aviation

SGL Carbon will begin serial production of landing gear made from braided carbon fiber material early this year. The landing skids will be installed in around 500 air taxis worldwide over the next two years.

The air taxis will be powered by several electric motors. To optimize the range of the taxis, every single gram counts. Measuring about two meters in length and 1.5 meters in width, the ultra-light landing skid will weigh less than three kilograms, making it about 15 percent lighter than a similar component made from aluminum. This increases the potential flight time capacity of the air taxi which is a key differentiator for the air taxi operator.

“With with our landing gear we help to shape this very new, promising application of manned, autonomous civil aviation. This involvement also demonstrates our wide range of services. From engineering, to prototype manufacture, to serial production with our own materials – all of our competences along the entire value chain made a contribution to the project ,” emphasizes Dr. Andreas Erber, Head of the Aerospace segment of the Composites – Fibers & Materials business unit at SGL Carbon.

The landing gear was developed in close collaboration between customer experts and specialists from SGL Carbon. The carbon fibers for the component are produced at the SGL Carbon plant in Muir of Ord, Scotland. The final part is being manufactured at the SGL Carbon site in Innkreis, Austria.

• New composite e-mobility application gains momentum
• Strengthening regional footprint in North America
• Potential for further extensions

Following the production of first prototypes of battery enclosures for a Chinese automotive manufacturer in 2018, SGL Carbon has now received a contract from a North-American automaker for high-volume serial production of carbon and glass fiber-based composite top and bottom layers for battery enclosures. The serial production of the components will start end of 2020. The carbon fibers and fabrics as well as the assembled components come from SGL Carbon’s fully integrated value chain. On top of this order, there is the potential for more extensions with further substantial volumes for the shared platform business of the manufacturer.

In addition, SGL Carbon has won a smaller volume contract from a European sports car manufacturer to serially produce bottom layers made of composite as of mid-2020. The company is additionally in talks with further automakers to develop and manufacture battery enclosure solutions for their e-car platforms.

“Driven by the increasing need for e-cars worldwide and thus for new flexible chassis platforms, our composite battery enclosures are a very promising new application in our product portfolio. The recent contract wins show that our approach of developing custom-made solutions based on our integrated value chain offers an excellent value proposition”, says Sebastian Grasser, Head of Automotive Segment.

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

As a result, India’s Ministry of Textiles is forecasting that the growth of technical textiles in the country will be over 18% annually in the next few years, from a value of US$16.6 billion in 2018 to US$28.7 billion in 2021.

Value addition

High value-added technical products such as wide-width digital printing substrates, carbon fabrics for high-performance composites, filter media, flame retardant barrier fabrics and heavy-duty membranes are now being coated on Monforts texCoat ranges and finished with the company’s industry-leading Montex stenters.

“Since we acquired the technology that our coating units are based on in 2015, we have made a lot of refinements,” says Hans. “All of these developments are reflected in higher coating accuracy and the resulting quality of the treated fabrics. At the same time, our latest multi-functional coating heads offer an unprecedented range of options, with a wide range of modules available.”

The texCoat user interface is now equipped with the unique Monforts visualisation system and the magnetic doctor blade has greater power reserves. Options include a carbon fibre-reinforced composite coating drum with a more scratch-resistant surface and maximum rigidity and remote control which simplifies exact adjustment for the operator.

Montex stenters in special executions are meanwhile ideal for the drying and finishing of both technical woven fabrics and nonwovens and characterised by high stretching devices in both length and width.

“The European-built Montex range of stenters has earned its leading position in the technical textiles market due to the overall robustness, reliability and economy of these machines,” Hans concludes. “Whatever the intended end-product – and we continue to discover potentially new areas in which technical textiles can be utilised all the time – we have the machine specification and know-how to turn ideas into reality. In India we also benefit from the strong sales and service support of A.T.E. Enterprises.”

Texchtextil India takes place alongside World of Composites at the Bombay Exhibition Centre in Mumbai from November 20-22.

• Reduction of material usage by up to 50 percent through innovative draping strategy in the production of fibre composite materials

In fibre reinforced plastic (FRP) production, stamp forming is one of the most economical processes for automated large-scale production, e.g. in the BMW i-series. However, the current processes are susceptible to draping errors and a high proportion of waste. An innovative process developed at the Institut für Textiltechnik of RWTH Aachen University, short ITA, can now significantly reduce the scrap rate and reduce the waste rate of high-priced reinforcing textiles, such as carbon fibre textiles, by up to 50 percent. Sven Schöfer from ITA achieved this effect with his work "Development of a textile-based material feed to increase the preform quality during stamp forming of reinforcing layers". On 10 September 2019, he won the third AVK Innovation Prize in the "Research and Science" category at Composite Europe in Stuttgart, Germany.

Current process
In stamp forming, clamping grippers are usually used in industry to feed the stacked individual layers to the forming process and position them on the lower tool via a clamping frame or hold-down device. Due to the clamping grippers, the cutting proportion of cost-intensive reinforcing textiles is high, as additional material at the textile edge is necessary with clamping systems. Other approaches to feeding the reinforcing semi-finished product during forming and simultaneously improving the draping quality are also not economical: they are usually only designed for certain textile cuts, cannot be automated, are prone to errors or are expensive special solutions.

There is currently no system in the industry that can apply retention forces along a final contour with low waste and remains flexible in terms of geometry.

Innovative approach of Sven Schöfer
The innovative process developed by Sven Schöfer works with a detachable textile joint, a so-called tufting seam. It allows the single layers to slide off during the forming process under a retention force dependent on the seam design.

This reduces or completely eliminates draping errors in previously critical areas, even with complex preform geometries. This leads to a significant increase in preform quality and a reduction in scrap rates. The process is also highly efficient, as tensile forces can be applied to any component geometry on near-net-shape blanks. This reduces the material input by up to 50 percent.

Hexcel, Arkema and their partners are pleased to announce that their joint collaborative project “HAICoPAS” has received approval from Bpifrance and the support (grant of 6 million euros) of France’s Investissements d’Avenir program.

HAICoPAS project is a collaborative project with a total amount of 13.5 million euros lead by Hexcel and Arkema and their industrial partners (Ingecal, Coriolis Composites, Pinette Emidecau Industries (PEI) et l'Institut de Soudure), and academia lead by CNRS (PIMM (CNRS - Arts et Métiers ParisTech - le Cnam), LTEN (CNRS - Université de Nantes). This project follows last year’s announcement of the strategic partnership between Hexcel and Arkema to develop high performance PEKK/carbon fiber UD tapes targeting composite parts for primary aerospace structures.

• Hexcel’s Composite Innovations For Aerospace, Automotive, Energy And Marine Applications At JEC World 2019 Hall 5 - Stand J41

STAMFORD, Conn. – At this year’s JEC World taking place in Paris on March 12-14, Hexcel will promote a wide range of composite innovations for customer applications in aerospace, automotive, energy and marine markets.

Aerospace Innovations

Hexcel’s HiTape® and HiMax™ dry carbon reinforcements were developed to complement a new generation of HiFlow™ resin systems, producing high quality aerospace structures using the resin infusion process. HiTape® was developed for the automated lay-up of preforms and HiMax™ is a range of optimized non-crimp fabrics (NCF). Both products incorporate a toughening veil to enhance mechanical properties, meeting the structural requirements for aerospace parts.

Visitors to JEC will see an Integrated Wing Panel demonstrator and an I-beam, both made with HiTape® reinforcements, and an Opticoms rib made with HiMax™ NCF. The Opticoms rib and I Beam were both manufactured using C-RTM (Compression Resin Transfer Molding). They were injected with Hexcel’s RTM6 resin in a process taking less than 5 minutes. The total manufacturing cycle for both parts was just 4.5 hours.

Also among the Aerospace exhibits, Hexcel will display a composite petal for a satellite antenna, manufactured by Thales Alenia Space Italia. The petal is part of a set of 24 deployable structural elements that form the large area reflector assembly used on board Low Earth Orbit (LEO) observation satellites. Thales Alenia Space Italia selected Hexcel’s HexPly® M18 prepreg for this application, acknowledging the superior mechanical and outgassing properties provided.

Another Hexcel prepreg application on show is a “zero” frame, manufactured by Aerofonctions for the engine area of Daher’s TBM 910/930 single-engine turboprop aircraft. Hexcel’s HexPly® M56 prepreg was selected by Daher for the “zero” frame – a product developed for Out of Autoclave applications that provides the same high quality and performance as autoclave-cured prepregs, from a simple vacuum bag cure in an oven.

With 50 years of experience behind its comprehensive range of high-strength, high-strain PAN-based carbon fibers, Hexcel continues to innovate, and is introducing two new fibers to its portfolio. HexTow® HM50 combines high modulus and high tensile strength, making it ideal for commercial and defense aircraft and engines. HexTow® 85 was developed specifically to replace rayon-based carbon fiber for ablative applications.

HexTow® carbon fiber holds the most qualified carbon fiber positions on aerospace programs in the industry and is the best unsized fiber available on the market. It provides excellent bonding interfacial properties with thermoplastic matrices and is the best-performing fiber for 3D printing applications.

Additive manufacturing is another area of expertise for Hexcel, using PEKK ultra-high performance polymers and HexAM™ technology to manufacture carbon-reinforced 3D printed parts. This
innovative process provides a weight-saving solution for intricate parts in highly demanding aerospace, satellite and defense applications. HexPEKK™ structures offer significant weight, cost and time-to-market reductions, replacing traditional cast or machined metallic parts with a new technology.

Hexcel is well known for its range of weight-saving, stiffness-enhancing honeycombs and the company adds value by providing a range of engineered core solutions to customers from facilities in the USA, Belgium and the newly opened Casablanca plant in Morocco. Hexcel’s engineered core capabilities enable highly contoured parts with precision profiling to be produced to exacting customer specifications. An example of such a part will be on display at JEC. Made from Aluminum FlexCore®, the part is CNC machined on both sides, and formed and stabilized with both peel ply and flyaway layers of stabilization. Aircraft engines benefit from a number of Hexcel core technologies including HexShield™ honeycomb that provides high temperature resistance in aircraft engine nacelles. By inserting a thermally resistant material into honeycomb cells, Hexcel provides a core product with unique heat-shielding capabilities that allows for the potential re-use of material after a fire event.

Hexcel’s Acousti-Cap® broadband noise-reducing honeycomb significantly improves acoustic absorption in aircraft engine nacelles. The acoustic treatment may be positioned at a consistent depth and resistance within the core, or can be placed in a pattern of varying depths and/or resistances (Multi-Degrees of Freedom and 3 Degrees Of Freedom), offering an acoustic liner that is precisely tuned to the engine operating conditions. These technologies have been tested at NASA on a full engine test rig and meet all 16 design conditions without trade-offs.

HexBond™ – the new name in Adhesives

Hexcel’s range of high performance adhesives has expanded considerably following the company’s acquisition of Structil. The company has now decided to unite the range by marketing all of its adhesive products using HexBond™ branding. The comprehensive range of HexBond™ structural film adhesives, foaming adhesive films, paste adhesives, liquid shims, epoxy fillets and Chromium free liquid primers is suitable for a wide range of applications in combination with Hexcel’s prepreg and honeycomb products.

Automotive Innovations

Hexcel’s carbon prepreg patch technology provides an innovative way of locally stiffening and reinforcing metal parts, providing noise and vibration management functionality. HexPly® prepreg patches consist of unidirectional carbon fiber impregnated with a fast curing epoxy matrix that has self-adhesive properties, enabling it to bond to metal in a highly efficient one-step process. These key technology properties are demonstrated in an 18.5kg aluminum subframe (that is 50% lighter than steel equivalents), which was reinforced with 500 grams of HexPly® prepreg and tested by Saint Jean Industries. The part demonstrates a significant reduction in noise, vibration and harshness (NVH). Other benefits include lower production costs, energy savings, increased driver comfort, production flexibility and part count reduction. With this technology Hexcel is a finalist in the JEC Innovation Awards 2019 in the Automotive Applications category.

HexPly® prepreg patch technology was also applied to a hybrid side sill demonstrator developed with Volkswagen and Dresden University to address future crash test requirements, specifically for electric cars. Combining fiber-reinforced plastic (FRP) with metal, the hybrid construction allows for optimum performance including weight savings, enhanced safety, increased energy absorption, battery protection in a crash situation and production flexibility.

Hexcel will also display a lightweight CFRP transmission crossmember produced from Hexcel’s high performance HexMC®-i 2000 molding compound. The transmission crossmember was developed in partnership with the Institute of Polymer Product Engineering (at Linz University), Engel and Alpex. As the part connects the chassis together and supports transmission it has to be stiff and strong, resisting fatigue and corrosion. Hexcel’s HexMC®-i 2000 was selected as the best-performing molding compound on the market, curing in as little as two minutes to produce lightweight, strong and stiff parts.
To produce the transmission crossmember HexMC®-i 2000 preforms are laid up in Alpex molds and compression-molded in a v-duo press that was tailored for the application by Engel. Ribs, aluminum inserts and other functions can be molded into the part using the single-stage process, reducing component-count. Any offcuts from the preforms can be interleaved between the plies of material to provide additional reinforcement in key areas - meaning that the process generates no waste.

Other Automotive promotions on Hexcel’s stand at JEC World include a composite leaf spring manufactured by ZF using HexPly® M901 prepreg. In contrast to steel leaf springs, composite versions offer many advantages including weight savings of up to 70%, high corrosion resistance, optimized system integration and superior performance. HexPly® M901 prepreg reduces the cure cycle to below 15 minutes and provides 15% higher mechanical performance, with enhanced fatigue properties. It also operates at high temperatures, providing a Tg of up to 200°C following a post cure.

Marine Innovations

Hexcel has a comprehensive range of products aimed at racing yacht and luxury boat builders that include America’s Cup, IMOCA class and DNV GL-approved prepregs, woven reinforcements and multiaxial fabrics for hull and deck structures, masts and appendages.

At JEC World Hexcel will display an IMOCA yacht mast manufactured by Lorima using HexPly® high modulus and high strength carbon fiber prepreg from Hexcel Vert-Le-Petit. Lorima is the exclusive official supplier of masts for IMOCA 60 class racing boats.

Hexcel’s HexTow® IM8 carbon fiber has been selected as the highest performing industrial carbon fiber on the market and will be used by spar and rigging manufacturer Future Fibres to manufacture their AEROrazr solid carbon rigging for all the teams in the 36th America’s Cup.

Hexcel’s HiMax™ DPA (Dot Pattern Adhesive) reinforcements are non-crimp fabrics supplied pre-tacked, allowing multiple fabrics to be laid-up more easily in preparation for resin infusion. Providing an optimal, consistent level of adhesion, they allow a faster and more consistent resin flow, as well as eliminating the use of spray adhesive for a healthier working environment and lower risk of contamination. Simply unrolled and applied to the mold or core layer before the introduction of resin, HiMax™ DPA fabrics are widely used in boat building, where lay-up times can be reduced by up to 50%.

Wind Energy Innovations

Hexcel has developed a range of HexPly® surface finishing prepregs and semi-pregs for wind turbine blades and marine applications. Providing a tough, durable and ready-to-paint surface without using in-mold coats, these products shorten the manufacturing cycle and reduce material costs. HexPly® XF2(P) prepreg is optimized for wind blades and has a ready-to-paint surface, straight from the mold, saving at least 2 hours of takt time.

Polyspeed® pultruded carbon laminates were developed for load-carrying elements in a blade structure and are manufactured with a polyurethane matrix that provides outstanding mechanical performance in terms of stiffness and durability. The blade manufacturing process is optimized, with increased throughput. The pultruded laminates are supplied in coils as continuous cross section profiles.
HiMax™ non-crimp fabrics using E-glass, high modulus glass and carbon fibers are also available in a wide range of unidirectional, biaxial and triaxial constructions. HiMax™ fabrics have applications throughout the turbine, from the stitched carbon fiber UDs used in the main structural elements, to glass fabrics and hybrids for blade shells and nacelles. There are also specialist applications such as lightweight fabrics for heated leading edge de-icing zones.

Hexcel is exhibiting at the Toulouse Space Show on June 26-28 to promote its latest technologies and innovations in composites for space applications. More than 3,000 visitors are expected at this major international forum that is dedicated to novel solutions for space.

Hexcel’s promotions will feature a number of 3D-printed flight-ready carbon fiber parts manufactured from HexAM™ additive manufacturing technology, combining high performance PEKK thermoplastics with aerospace grade carbon fiber. HexPEKK™ structures offer significant weight, cost and time-to-market reductions, replacing traditional cast or machined metallic parts in highly demanding aerospace, satellite and defense applications.

Other Hexcel solutions for space applications include carbon fiber, prepregs and honeycomb materials with proven performance for satellite structures and launchers.

Hexcel Corporation is a leading advanced composites company. It develops, manufactures and markets lightweight, high-performance structural materials including carbon fibers, specialty reinforcements, prepregs and other fiber-reinforced matrix materials, honeycomb, adhesives, engineered core and composite structures for use in commercial aerospace, space and defense and industrial applications.

STAMFORD, February 26, 2018 - at JEC World 2018, taking place in Paris March 6-8, Hexcel will display an array of product innovations for customer applications in aerospace, automotive, wind energy and marine markets.
Hexcel’s banner at the exhibit hall entrance features the Airbus H160 helicopter and A350 XWB aircraft, both with carbon fiber livery to acknowledge the high Hexcel composites content in both programs. Hexcel’s reinforcements, prepregs, adhesives and honeycomb materials were selected for the H160’s composite fuselage structures and main rotor blades, contributing to the lightweight fuel-saving design and performance optimization. Airbus has loaned Hexcel an H160 BLUE EDGE blade to display on the booth.

Among the Aerospace promotions at Hexcel’s booth are carbon-reinforced 3D printed parts, made from Hexcel’s HexAM™ additive manufacturing technology that uses PEKK ultra-high performance polymers. Hexcel acquired this technology from Oxford Performance Materials in December 2017 to provide a weight-saving solution for intricate parts in highly demanding aerospace, satellite and defense applications. HexPEKK™ structures offer significant weight, cost and time-to-market reductions, replacing traditional cast or machined metallic parts with a new technology.

Aircraft engines benefit from a number of Hexcel technologies that will be promoted at JEC 2018, including HexShield™ honeycomb that provides high temperature resistance in aircraft engine nacelles. By inserting a thermally resistant material into honeycomb cells, Hexcel provides a core product with unique heat-shielding capabilities that allows for the potential re-use of material after a fire event.
Another honeycomb innovation from Hexcel is Acousti-Cap® broadband noise-reducing honeycomb that significantly improves acoustic absorption in aircraft engine nacelles. The acoustic treatment may be positioned at a consistent depth and resistance within the core, or can be placed in a pattern of varying depths and/or resistances (Multi-Degrees of Freedom and 3 Degrees Of Freedom), offering an acoustic liner that is precisely tuned to the engine operating conditions. These technologies have been tested at NASA on a full engine test rig and meet all 16 design conditions without trade-offs. An example of this technology will be on display at JEC 2018.

Rounding off the aircraft engine exhibits is a CTi fan blade for new generation lightweight turbofan engines from Rolls-Royce, manufactured from Hexcel’s HexPly® M91 high toughness and impact-resistant epoxy prepreg. Hexcel supplies HexPly® M91 as slit tape for the automated lay-up of the complex aerodynamic shape, with a constantly changing thickness across the blade length. The blade which is thinner and lighter than titanium fan blades is currently undergoing flight tests.
Hexcel’s HiTape® and HiMax™ dry carbon reinforcements that were developed for the automated lay-up of preforms for resin-infused aerospace structures will be promoted at the show. Two demonstrator parts, one made with HiMax™ and one with HiTape®, were both infused with HexFlow® RTM6 resin to demonstrate the potential benefits of an integrated design for aircraft skins, spars and stiffeners that meets OEM requirements for production rate increases and cost effectiveness.

Hexcel is also introducing its new range of HiFlow™ advanced liquid resins for aerospace structures manufactured by liquid molding technologies. Based on novel proprietary chemistry, the new resin family will enhance the performance of composites and ease processing when combined with HiTape® and HiMax™ dry carbon reinforcements. HiFlow™ HF610 is the first resin in the range.
Hexcel’s range of high performance adhesives has expanded considerably following the company’s acquisition of Structil last October. Hexcel is relaunching the acquired products under the new HexBond™ brand name at JEC World. This fast-growing range of pastes, liquid shim and film adhesives has a wide spectrum of operating temperatures and is in qualification with a large number of aerospace and industrial OEMs.
In the Planet Aerospace area at JEC, Daher and Hexcel will jointly display an aircraft spar manufactured from HexPly® M56 prepreg. Hexcel’s Neil Parker and Daher R&T Director Dominique Bailly will give a joint presentation focusing on the materials used and the benefits for the finished part. The aircraft spar was designed and manufactured by Daher using Hexcel’s HexPly® M56 prepreg, in slit tape format, that was developed for automated deposition and out-of-autoclave curing. The spar was manufactured using only the vacuum bag process and demonstrates very low porosity levels. It is currently undergoing testing and validation through CORAC funding.

Hexcel’s Automotive promotions at JEC World 2018 include a new prepreg for composite leaf springs, HexPly® M901. In contrast to steel leaf springs used for suspension on vans, trucks and SUVs, newer composite versions offer many advantages including weight savings of up to 70%, high corrosion resistance, optimized system integration and superior performance. Hexcel’s HexPly® M901 prepreg raises the bar further, reducing mold cure time below 15 minutes, a 50% reduction compared to standard industrial prepregs. HexPly® M901 provides 15% higher mechanical performance, with enhanced fatigue properties. It also operates at high temperatures, providing a Tg of up to 200°C following a post cure. Hexcel’s expertise in manufacturing heavy weight glass UD prepregs, with fiber areal weights of up to 1600gsm, allows the company to offer a highly cost-competitive solution for the rapid manufacture of these safety critical components.

Hexcel is constantly seeking ways to ensure that customers obtain the maximum benefit from composites and has recently acquired state-of-the-art simulation technology that accurately predicts how HiMax™ non-crimp fabrics will drape in a mold. Working in collaboration with Nottingham University Hexcel has created a car seat shell, for which the material selection was optimized using this new drape simulation technology. Visitors to Hexcel’s stand at JEC will see an on-screen demonstration that illustrates how the simulation tool operates, predicting process and performance and ensuring that the optimum fabric architecture is quickly identified, reducing the need for expensive trial programs.
Hexcel’s HexMC®-i 2000 carbon fiber/epoxy molding compound has been successfully used by Audi to manufacture a high-performance engine cross brace. HexMC®-i is a fast curing high-performance molding material, suitable for the series production of complex shaped parts and providing excellent mechanical properties. The Audi cross brace covers the engine, providing torsional stiffness for enhanced drive dynamics.

Hexcel’s product offering for customers in the Marine industry has expanded following the acquisition of Formax in 2016 and Structil in 2017. At JEC World, Hexcel will promote its enhanced portfolio of carbon fibers, prepregs, woven reinforcements and multiaxial fabrics for builders of racing catamarans and luxury yachts.
Marine customers have supplied a number of parts for display to illustrate their expertise in manufacturing composite structures from Hexcel materials. These include part of a Diam 24 yacht mast made by ADH Inotec from Hexcel’s HexPly® M79 fast curing, low temperature cure prepreg. ADH Inotec purchased the prepreg from Composites Distribution, a Hexcel Official Distributor that also supplied HexPly® M9.6 prepreg to Lorima for the Outremer 5X catamaran mast section on display. Part of Lorima’s 42m wing mast for a multihull racing boat made with HexPly® prepreg from Vert-Le-Petit (formerly Structil) will complete the marine display.

Hexcel’s innovations for Wind Energy include Polyspeed® pultruded laminates for load-carrying elements in wind blades. These continuous cross-section profiles, made from a polyurethane matrix reinforced with unidirectional carbon fiber, provide consistently high mechanical properties, including high stiffness, fracture toughness and shear strength, combined with low weight and durability. Visitors to Hexcel’s stand will see a 2m diameter coil of pultruded carbon laminate that contains 255m of material in a single roll. This technology offers an economical way of reinforcing large-scale composite structures such as wind turbine blades. Hexcel will also launch its surface finishing prepreg for wind turbine blades and components. This provides a tough, durable and ready-to-paint blade surface without the use of gel coat and results in faster blade manufacture, saving time in production and reducing material costs. The benefits of the new surfacing prepreg will be demonstrated via a wind blade exhibit that has been given four different treatments across the blade surface. These include a section with gel coat, a section of standard prepreg without gel coat, and a section where a fleece has been added to improve surface quality but still requires preparation before painting due to pin holes. The final section made with new HexPly® XF2P surfacing prepreg has a ready-to-paint surface, straight from the mold, without any requirement for gel coat, fleece or finishing operations.

Hexcel Corporation is proud to announce the unveiling of the third H160 prototype from Airbus Helicopters, featuring a striking carbon-inspired livery that represents the composite materials Hexcel supplies for the helicopter.

This gesture follows Hexcel’s announcement in June that its reinforcements, prepregs, adhesives and honeycomb materials had been selected for the H160’s composite fuselage structures and main rotor blades. The H160 was designed by Airbus Helicopters to create added-value for customers in terms of performance, economic competitiveness, safety and comfort. The use of Hexcel’s composite materials throughout the structure contributes to the lightweight fuel-saving design and performance optimization.
Airbus Helicopters decided to promote the H160 program and its high carbon fiber content in a way that recalls the livery previously used for the A350 XWB. The A350 XWB has a structure that is 53% composites and Hexcel supplies the carbon fiber prepreg for all of the aircraft’s composite primary structures.
The newly unveiled H160 prototype is a fitting tribute to the 40-year partnership between Hexcel and Airbus Helicopters.