From the Sector

Reset
33 results
23.06.2022

Lectra announces the launch of its Automotive Cutting Room 4.0 offer

The automotive industry currently faces a complex set of market dynamics: rising material and transport costs, reduced budgets, changing consumer expectations, increasing challenges related to CSR, etc. In this context, improving efficiency across the whole value chain has become a strategic priority for vehicle and equipment manufacturers. Lectra supports its customers by designing and developing cutting-edge solutions that combine software, equipment, data and services to make its offer the gateway to Industry 4.0.
 
With Industry 4.0, a new range of possibilities is opening up to businesses. The concept and its technologies bring in new value creation and cost control models based on synchronized, flexible and fast processes.
 

The automotive industry currently faces a complex set of market dynamics: rising material and transport costs, reduced budgets, changing consumer expectations, increasing challenges related to CSR, etc. In this context, improving efficiency across the whole value chain has become a strategic priority for vehicle and equipment manufacturers. Lectra supports its customers by designing and developing cutting-edge solutions that combine software, equipment, data and services to make its offer the gateway to Industry 4.0.
 
With Industry 4.0, a new range of possibilities is opening up to businesses. The concept and its technologies bring in new value creation and cost control models based on synchronized, flexible and fast processes.
 
The Automotive Cutting Room 4.0 offer is a set of solutions connected to one other: Vector, the fabric cutting equipment offering the best performance in the market; Empower, a new generation of digital services to leverage Vector's capabilities; Valia, the heart of the new offer, a software for preparing and scheduling production; and Algopex, an application for exploiting and capitalizing on all the data generated by the cutting room, so you can make the best decisions as quickly as possible.
 
Connecting up all the elements of the Automotive Cutting Room 4.0 offer delivers this unprecedented value and enables an unparalleled level of performance to be achieved. Nicolas Favreau, Lectra’s Automotive Marketing Strategy Director, explains: “When the whole cutting room process is digitalized, the data generated are centralized and accessible in real time, helping our customers to make the best decisions at every step of the production process. The benefits are huge. For example, the key performance indicators from the offer’s first users show productivity gains of around 5% and a reduction in material consumption of nearly 2%. That’s unheard of! These results, combined with the agility that the Automotive Cutting Room 4.0 brings and the complete process control, demonstrate the offer’s maximum relevance.”

Source:

Lectra 

21.06.2022

SHIMA SEIKI to exhibit at Pitti Filati 91

SHIMA SEIKI ITALIA S.p.A. will exhibit at the 91st edition of the Pitti Immagine Filati exhibition in Florence, Italy from 29th June till 1st July, 2022. Products exhibited will include the SWG-FIRST124 and N.SIR123SP computerized flat knitting machines as well as APEXFiz™ design software.

The renewed SWG-FIRST124 is a synthesis of all of SHIMA SEIKI’s experience and know-how in computerized shaped knitting, realizing a tremendous range of knitting from full-fashioning and rib shaping to integral knitting. This all-purpose capability is made possible by the revolutionary SlideNeedle™, which, together with loop pressers and transfer jacks, offers remarkable variety, expanding the boundaries of flat knitting with the capability to produce garments that were previously impossible to produce.

SHIMA SEIKI ITALIA S.p.A. will exhibit at the 91st edition of the Pitti Immagine Filati exhibition in Florence, Italy from 29th June till 1st July, 2022. Products exhibited will include the SWG-FIRST124 and N.SIR123SP computerized flat knitting machines as well as APEXFiz™ design software.

The renewed SWG-FIRST124 is a synthesis of all of SHIMA SEIKI’s experience and know-how in computerized shaped knitting, realizing a tremendous range of knitting from full-fashioning and rib shaping to integral knitting. This all-purpose capability is made possible by the revolutionary SlideNeedle™, which, together with loop pressers and transfer jacks, offers remarkable variety, expanding the boundaries of flat knitting with the capability to produce garments that were previously impossible to produce.

The N.SIR123SP computerized knitting machine with intarsia capability features a special loop presser bed for producing hybrid inlay fabrics with both knit and weave characteristics. N.SIR123SP will also feature the special i-Plating option, capable of alternating yarn colors in any pattern, producing jacquard-like designs using plain jersey stitch. Plating can be performed within the same course and for individual needles. In combination with the loop presser and spring-type moveable sinker system even greater diversity in knit design is possible.

APEXFiz™ is subscription-based design software that supports the creative side of fashion from planning and design to colorway evaluation, realistic fabric simulation and 3D virtual sampling. Virtual samples are a digitized version of sample making that are accurate enough to be used effectively as prototypes, replacing physical sampling and consequently reducing time, cost and material that otherwise go to waste. APEXFiz™ thereby helps to realize sustainability and digitally transform the fashion supply chain.

Continuing from past editions of Pitti Filati are knit samples produced in collaboration with Italian designer Vittorio Branchizio. Staff at the SHIMA SEIKI booth will be donning knit uniforms produced as a collaborative effort between SHIMA SEIKI ITALIA, knitting companies and yarn companies.

Source:

SHIMA SEIKI MFG., LTD.

20.06.2022

Lectra joins Euronext Tech Leaders

Lectra, whose connected industrial equipment and software facilitate the digital transformation and Industry 4.0 transition of fashion, automotive and furniture companies, announces its selection for the new Euronext Tech Leaders stock market index. This brings Lectra into the community of European technology leaders identified by Euronext as innovative and high-growth companies.

The new Euronext Tech Leaders market index, launched on June 7, comprises 100 European technology companies listed on the Euronext markets, which meet various performance and growth criteria. With the launch of this initiative, Euronext aims to offer better visibility and new services to selected European technology leaders.

Lectra, whose connected industrial equipment and software facilitate the digital transformation and Industry 4.0 transition of fashion, automotive and furniture companies, announces its selection for the new Euronext Tech Leaders stock market index. This brings Lectra into the community of European technology leaders identified by Euronext as innovative and high-growth companies.

The new Euronext Tech Leaders market index, launched on June 7, comprises 100 European technology companies listed on the Euronext markets, which meet various performance and growth criteria. With the launch of this initiative, Euronext aims to offer better visibility and new services to selected European technology leaders.

Lectra is one of the 41 French companies that are now members of Euronext Tech Leaders. The company, founded in 1973 on a close relationship with fashion industry players, has also for the last three decades worked globally with automotive equipment and furniture manufacturers. In its three strategic markets, Lectra sells connected equipment that optimizes the cutting processes of fabric, leather and other soft materials used by manufacturers, and markets software and services that streamline their production processes while enabling them to be more agile and make considerable material savings.

In fashion, through the use of market data – made accessible and exploitable by the Internet of Things, the cloud, artificial intelligence and big data – Lectra’s software solutions also enable a better understanding of consumers’ behavior. They therefore facilitate strategic decision-making for brands, manufacturers and distributors at the key steps in the value chain of design, production and distribution. In this industry, the impact of Lectra’s solutions on reducing material consumption is even greater because it takes effect as early as the garment design stage.

Technology and innovation are therefore at the heart of Lectra’s strategy, with the company aiming to become a key player in Industry 4.0 in its strategic markets by 2030.

Source:

Lectra

(c) Hochschule Albstadt-Sigmaringen
09.06.2022

Hochschule Albstadt-Sigmaringen: Neue Software, die Chaos in textiler Fertigung beseitigt

Nadelbrüche oder Nähfehler müssen in der Produktion von Textilien schnell behoben werden – ansonsten geht wertvolle Zeit verloren, die Unternehmen bares Geld kostet. Masterstudierende der Hochschule Albstadt-Sigmaringen haben jetzt in einem fakultätsübergreifenden Projekt eine Software entwickelt, die dieses Problem minimiert. Damit reagierten sie auf das Problem, dass es bislang keine kostengünstige, flexible Lösung am Markt gibt, um in einer vernetzten textilen Fertigung einen optimalen Materialfluss planen und diesen jederzeit rückverfolgen zu können.

Nadelbrüche oder Nähfehler müssen in der Produktion von Textilien schnell behoben werden – ansonsten geht wertvolle Zeit verloren, die Unternehmen bares Geld kostet. Masterstudierende der Hochschule Albstadt-Sigmaringen haben jetzt in einem fakultätsübergreifenden Projekt eine Software entwickelt, die dieses Problem minimiert. Damit reagierten sie auf das Problem, dass es bislang keine kostengünstige, flexible Lösung am Markt gibt, um in einer vernetzten textilen Fertigung einen optimalen Materialfluss planen und diesen jederzeit rückverfolgen zu können.

Insgesamt 23 Studierende aus den Studiengängen Textil- und Bekleidungsmanagement (Fakultät Engineering) und Systems Engineering (Fakultät Informatik) realisierten das Industrieprojekt mithilfe von Prof. Matthias Kimmerle und Prof. Dr. Derk Rembold. Sie entwickelten zwei Accessoires: einen Shopper, der auch Platz für eine Yogamatte bietet, sowie eine Flaschentasche, bei der Kreditkarten oder Schlüssel beispielsweise im Fitnessstudio bequem an der Trinkflasche verstaut werden können. Das von den Studierenden entwickelte Manufacturing Execution System (MES) hilft bei der optimalen Planung, Steuerung und Optimierung der Produktion.

Die Idee der Studierenden basiert auf einer bereits existierenden App, die an einer Industrienähmaschine Echtzeitanalysen erstellen kann. Nach einer ausgiebigen Phase der Ideenfindung, Produktion und Programmierung wollen die Studierenden ihr MES nun so optimieren, dass sie die bereits vorhandene Software bereichert.

Source:

Hochschule Albstadt-Sigmaringen

07.06.2022

EFI confirms Acquisition of Inèdit Software for textile printing

Electronics For Imaging, Inc. announced that it has acquired Inèdit Software S.L., a developer of raster image processors (RIPs) and related software for digital industrial textile printing. The acquisition extends EFI’s strategy to accelerate digital transformation in industrial print through investments that advance the company’s presence and capabilities in Packaging & Corrugated, Display Graphics, Textile, and Building Materials/Décor applications. Inèdit will be integrated into the Reggiani textile business.

Electronics For Imaging, Inc. announced that it has acquired Inèdit Software S.L., a developer of raster image processors (RIPs) and related software for digital industrial textile printing. The acquisition extends EFI’s strategy to accelerate digital transformation in industrial print through investments that advance the company’s presence and capabilities in Packaging & Corrugated, Display Graphics, Textile, and Building Materials/Décor applications. Inèdit will be integrated into the Reggiani textile business.

Similar to EFI’s Fiery® digital front end and RIP technologies for the digital commercial and industrial printing markets, Inèdit’s neoStampa product is a recognized benchmark solution for RIPs in digital textile printing. The Inèdit product portfolio features advanced workflow solutions for textile profiling, calibration, design integration and much more. Inèdit’s RIP technology is employed across the worldwide textile industry and is one of the leading RIPs used to drive EFI Reggiani digital printers and other digital industrial textile printer brands. As part of EFI Reggiani, Inèdit will continue to support products for a broad range of digital printers.

Source:

EFI

06.06.2022

SHIMA SEIKI to exhibit at ITM 2022

SHIMA SEIKI MFG. will participate in the ITM 2022 International Textile Machinery Exhibition in Istanbul, Turkey.

SHIMA SEIKI MFG. will participate in the ITM 2022 International Textile Machinery Exhibition in Istanbul, Turkey.

SHIMA SEIKI will exhibit a wide range of its products, including proposals in seam-free WHOLEGARMENT® knitting technology that offers an alternative to labor-intensive manufacturing in Turkey and other international markets. Featured is the flagship MACH2XS WHOLEGARMENT® knitting machine with original SlideNeedle™ on four needle beds and spring-loaded moveable sinkers with expanded patterning capability, the MACH2VS V-bed machine for producing WHOLEGARMENT® items using every other needle, as well as the compact SWG091N2 for producing smaller WHOLEGARMENT® items and accessories. A brand new proposal in V-bed WHOLEGARMENT® knitting will also be introduced in the form of the N.SVR183 machine. N.SVR123SP features a special loop presser bed that can produce hybrid inlay fabrics with both knit and weave characteristics. N.SVR123SP at ITM will feature the special i-Plating option, capable of alternating yarn colors in any pattern, producing jacquard-like designs using plain jersey stitch for even greater diversity in knit design. Meanwhile N.SSR112 offers industry-leading technology in an economical yet reliable package made in Japan. Also on display is the SFG20 glove knitting machine.

Demonstrations will be performed on SHIMA SEIKI’s SDS®-ONE APEX4 design system. At the core of the company’s “Total Fashion System” concept, SDS®-ONE APEX4 provides comprehensive support throughout the production supply chain, integrating production into one smooth and efficient workflow from yarn development, product planning and design, to production and even sales promotion. Especially effective is the way SDS®-ONE APEX4 improves on the design evaluation process with its ultra-realistic simulation capability, whereby virtual samples replace physical sampling, consequently reducing time, cost and material that otherwise go to waste. The same capability is present in APEXFiz™ subscription-based design software. Installed on personal computers, APEXFiz™ features the same functionality as SDS®-ONE APEX4, but with the added versatility to adapt to different work styles and business environments including teleworking and telecommuting. Digital prototyping using virtual samples on SDS®-ONE APEX4 and APEXFiz™ help to digitally transform the fashion supply chain for realizing sustainable manufacturing. APEXFiz™ will be shown along with SHIMA SEIKI’s yarnbank™ digital yarn web platform that further enhances the realism of virtual samples.

Source:

SHIMA SEIKI MFG., LTD.

SHIMA SEIKI releases digital content web service "SHIMA Datamall™" (c) SHIMA SEIKI MFG., LTD.
01.06.2022

SHIMA SEIKI releases digital content web service "SHIMA Datamall™"

SHIMA SEIKI MFG., LTD. announces the release of its new "SHIMA Datamall™" digital content web service.

SHIMA Datamall™ is an online service that allows users to search, browse and purchase a variety of useful data for the planning, production and sales of fashion items. With SHIMA Datamall, users of the SDS®-ONE APEX series 3D design system, APEXFiz™ Design subscription software and SHIMA SEIKI flat knitting machines will be able to streamline their operations and further promote the digital transformation of textile manufacturing, thereby realizing a shift toward sustainable manufacturing.

Digital content available on SHIMA Datamall™, together with yarn data from the yarnbank™ digital yarn sourcing web service, are meant to support knit manufacturing from planning and design to production and sales, by arranging the data on SDS®-ONE APEX and APEXFiz™.

SHIMA SEIKI MFG., LTD. announces the release of its new "SHIMA Datamall™" digital content web service.

SHIMA Datamall™ is an online service that allows users to search, browse and purchase a variety of useful data for the planning, production and sales of fashion items. With SHIMA Datamall, users of the SDS®-ONE APEX series 3D design system, APEXFiz™ Design subscription software and SHIMA SEIKI flat knitting machines will be able to streamline their operations and further promote the digital transformation of textile manufacturing, thereby realizing a shift toward sustainable manufacturing.

Digital content available on SHIMA Datamall™, together with yarn data from the yarnbank™ digital yarn sourcing web service, are meant to support knit manufacturing from planning and design to production and sales, by arranging the data on SDS®-ONE APEX and APEXFiz™.

Membership is not limited to users of SHIMA SEIKI products. Anyone can search and browse from digital data comprising over 6,000 items, free of charge. Information gathered on SHIMA Datamall is useful for product planning and ideas for new collections. SHIMA SEIKI users can furthermore purchase and download data to facilitate communication with suppliers.

More information:
Shima Seiki digital yarn
Source:

SHIMA SEIKI MFG., LTD.

(c) Wiser Globe
18.05.2022

WOX by Wiser Tech hit Denim Première Vision with its futuristic design

For the first time at an in-person event, WOX by Wiser Tech hits Denim Première Vision, with its futuristic design and features leveraging Wiser Wash’s innovative potential. WOX machinery generation combines advanced hardware technology and software algorithms working on the cloud, laying new innovative foundations for fashion all over the world.

Making the finishing technologies fully traceable and accessible thanks to the advanced application of Wiser Tech Artificial Intelligence (AI) on the cloud system, WOX is one of the first of these technologies promising to redefine the entire market. Standing for Wiser Ozone X-perience, WOX physically consists of an ozone drum and generator – but, in its spirit, it was designed as a network object that provides data to Artificial Intelligence algorithms. With this feature it is really one-of-a kind in the industry, thanks to Artificial Intelligence’s potential to transform the existing business models and redefine the production process by developing new practices based on data analytics.

For the first time at an in-person event, WOX by Wiser Tech hits Denim Première Vision, with its futuristic design and features leveraging Wiser Wash’s innovative potential. WOX machinery generation combines advanced hardware technology and software algorithms working on the cloud, laying new innovative foundations for fashion all over the world.

Making the finishing technologies fully traceable and accessible thanks to the advanced application of Wiser Tech Artificial Intelligence (AI) on the cloud system, WOX is one of the first of these technologies promising to redefine the entire market. Standing for Wiser Ozone X-perience, WOX physically consists of an ozone drum and generator – but, in its spirit, it was designed as a network object that provides data to Artificial Intelligence algorithms. With this feature it is really one-of-a kind in the industry, thanks to Artificial Intelligence’s potential to transform the existing business models and redefine the production process by developing new practices based on data analytics.

The goal? To provide textile manufacturers with total control over their production, with credible sustainable solutions to address the most pressing environmental issues of the industry.

Source:

Wiser Globe / Menabò Group srl

05.05.2022

Monforts at Techtextil showcasing its finishing and coating technologies

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

Energy prices are rising steeply everywhere and a particular emphasis for Monforts in Frankfurt will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as better insulation of the treatment chambers or the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air resulting in a radical reduction in the conventional heat supply required compared to gas and thermal oil heating. The modular system for heat recovery can also be extended for exhaust air cleaning and odour elimination. Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation including modification of the heating source.

With the Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

All of these very different materials require coating and finishing for maximum efficiency, using Monforts technologies which provide the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

The Monforts EcoApplicator offers further potential for sustainably achieving perfect finishes via a precise direct application system, as an alternative to conventional padding – where fabrics are immersed in a bath of the required finishing chemicals. It can significantly further reduce the energy and water required and finishes can be applied on just one side of the fabric, or both, and even separately on each side, to be sealed in place via different heating zones in the stenter.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

03.05.2022

DOMO: Mechanische Struktursimulation für PA6-GF-Werkstoffe

  • Das MMI (Materialmodellierung, mechanische Berechnung und Spritzgusssimulation)-Team für fortgeschrittene Simulationstechnologien bietet erheblich verbesserten Service für PA6-GF-Werkstoffe
  • Integrative Simulationsumgebung lässt sich effektiv mit der Digimat-Software anwenden und gewährleistet präzise und robuste Finite-Elemente-Analysen

DOMOs fortschrittliche Simulationsumgebung MMI für PA66-Bauteile gilt auf dem Markt bereits als Referenz für präzise Simulationen. Ab sofort unterstützt dieses Simulationstool OEMs und Bauteillieferanten bei der Entwicklung von leistungsfähigen, leichten und kosteneffizienten Bauteilen aus PA6. Mit dem DOMO Service Hub können Bauteilentwickler ihre Polyamidlösungen somit schneller in Serie bringen.

Bei glasfaserverstärkten Materialien muss die Ausrichtung der Glasfasern berücksichtigt werden, die während des Spritzgussverfahrens entsteht. Dabei ermöglicht die Digimat-Software eine genaue integrative Simulation. DOMO besitzt ein umfangreiches Fachwissen bei der integrativen Simulation der TECHNYL® A-Serie von PA66-GF-Materialien und ist daher in der Lage, präzise Bauteilsimulationen durchzuführen.

  • Das MMI (Materialmodellierung, mechanische Berechnung und Spritzgusssimulation)-Team für fortgeschrittene Simulationstechnologien bietet erheblich verbesserten Service für PA6-GF-Werkstoffe
  • Integrative Simulationsumgebung lässt sich effektiv mit der Digimat-Software anwenden und gewährleistet präzise und robuste Finite-Elemente-Analysen

DOMOs fortschrittliche Simulationsumgebung MMI für PA66-Bauteile gilt auf dem Markt bereits als Referenz für präzise Simulationen. Ab sofort unterstützt dieses Simulationstool OEMs und Bauteillieferanten bei der Entwicklung von leistungsfähigen, leichten und kosteneffizienten Bauteilen aus PA6. Mit dem DOMO Service Hub können Bauteilentwickler ihre Polyamidlösungen somit schneller in Serie bringen.

Bei glasfaserverstärkten Materialien muss die Ausrichtung der Glasfasern berücksichtigt werden, die während des Spritzgussverfahrens entsteht. Dabei ermöglicht die Digimat-Software eine genaue integrative Simulation. DOMO besitzt ein umfangreiches Fachwissen bei der integrativen Simulation der TECHNYL® A-Serie von PA66-GF-Materialien und ist daher in der Lage, präzise Bauteilsimulationen durchzuführen.

Die neuen MMI-PA6-GF Materialkarten können für eine Vielzahl von Glasfaserkonzentrationen und -temperaturen sowie für elastische und elastoplastische Materialmodelle mit Versagensindikatoren eingesetzt werden. Diese sind in der Digimat Software verfügbar und führen zu den gleichen präzisen Ergebnissen wie bei den TECHNYL® A PA66-Werkstoffen. Die neuen Materialkarten heben somit die PA6-Datenbank auf das gleiche Leistungsniveau wie PA66 an. Im nächsten Schritt werden in die Digimat-Datenbank auch crashspezifische und thermische Modelle eingepflegt.

„Dank der präzisen MMI-Simulation können TECHNYL® Bauteile entwickelt werden, die leichter, leistungsfähiger und kosteneffizienter sind“, erklärt Gilles Robert, Material Expert bei DOMO. „Unsere Kunden profitieren von kürzeren Entwicklungszeiten und haben eine bessere Kontrolle über die internen Kosten. Der kontinuierliche Aufbau der TECHNYL®-Materialdatenbank erweitert das Anwendungsfeld dieser Simulationsumgebung auf PA6 Bauteile.“

Source:

DOMO Chemicals / Marketing Solutions NV

(c) UNCG
07.04.2022

Archroma partners with University of North Carolina Greensboro on color expert education

Archroma, a leader in specialty chemicals towards sustainable solutions, has announced the launch of a collaboration with the University of North Carolina Greensboro (UNCG) and its Consumer, Apparel, and Retail Studies (CARS) department, aiming to further the education of its students in the area of color management expertise.

As per the agreement, Archroma will donate its color management tools for their design projects, gaining hands-on expertise that equips them for successful careers in the fashion and textiles industries.

The students will have access to a complete set of the ready-to-use color library developed by Archroma for cotton and polyester. The library, well known among fashion designers and stylists as the Color Atlas by Archroma®, which was launched in 2016 to provide off-the-shelf color inspiration that can be implemented in production with just a few clicks.

Today, the Color Atlas contains 4’320 colors applicable on cotton poplin, almost the double compared to similar tools available to textile and fashion specialists, and 1,440 colors on polyester.

Archroma, a leader in specialty chemicals towards sustainable solutions, has announced the launch of a collaboration with the University of North Carolina Greensboro (UNCG) and its Consumer, Apparel, and Retail Studies (CARS) department, aiming to further the education of its students in the area of color management expertise.

As per the agreement, Archroma will donate its color management tools for their design projects, gaining hands-on expertise that equips them for successful careers in the fashion and textiles industries.

The students will have access to a complete set of the ready-to-use color library developed by Archroma for cotton and polyester. The library, well known among fashion designers and stylists as the Color Atlas by Archroma®, which was launched in 2016 to provide off-the-shelf color inspiration that can be implemented in production with just a few clicks.

Today, the Color Atlas contains 4’320 colors applicable on cotton poplin, almost the double compared to similar tools available to textile and fashion specialists, and 1,440 colors on polyester.

Beside the physical Color Atlas library, the students in the CARS program will also have access to the full digital files for use in the industry-leading 3D fashion design and development software Browzwear VSticher.

The students will be able to use the Color Atlas books and the digital data as a color selection resources to use in a variety projects and assignments.

Source:

Archroma / EMG

31.03.2022

Monforts at Techtextil North America

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Advanced machine operation
With the highly intuitive Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Versatility is the key
Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

Source:

AWOl Media / A. Monforts Textilmaschinen GmbH & Co. KG

13.03.2022

JEC Group supports Composites Expert To launch E-learning Composites Academy

On March 10th, JEC Group and Composites Expert have signed a partnership agreement to promote E-learning Composites Academy, the first 4.0 training platform dedicated to manufacturing processes of composite materials.

This partnership will start with two first steps: an introduction webinar session on March 15th at 4pm CET, and two sessions of training during JEC World 2022, on Tuesday, May 3rd and Wednesday, May 4th, in Paris where Composites Expert will present the E-learning Composites Academy, a new pedagogical approach aimed at appropriating knowledge of polymer transformation specially developed by Composites Expert.

Tools have been designed to combine the theoretical part (E-Learning course platform) and the practical part (BOXs, software, process simulator, exercises through manipulation) to observe complex phenomena, with the aim of mastering and optimising transformation processes. The aim of this presentation is to introduce people to the learning method and the interactivity of the teaching aids used in industry and education.

On March 10th, JEC Group and Composites Expert have signed a partnership agreement to promote E-learning Composites Academy, the first 4.0 training platform dedicated to manufacturing processes of composite materials.

This partnership will start with two first steps: an introduction webinar session on March 15th at 4pm CET, and two sessions of training during JEC World 2022, on Tuesday, May 3rd and Wednesday, May 4th, in Paris where Composites Expert will present the E-learning Composites Academy, a new pedagogical approach aimed at appropriating knowledge of polymer transformation specially developed by Composites Expert.

Tools have been designed to combine the theoretical part (E-Learning course platform) and the practical part (BOXs, software, process simulator, exercises through manipulation) to observe complex phenomena, with the aim of mastering and optimising transformation processes. The aim of this presentation is to introduce people to the learning method and the interactivity of the teaching aids used in industry and education.

“One of JEC Group’s objectives is to develop access to education to help the composites industry to attract and train talented professionals. So, we are very proud to announce this partnership and to support Composites Expert initiatives, as joining common efforts and strategies will benefit to the overall industry”, stated Anne-Carole Barbarin, Content and Product development Director.

“The partnership with JEC Group is a major step towards the development of our training platform, while several manufacturers have already supported us, such as Arkema, Chomarat, Daher, Diatex, Pinette PEI, Porcher, Sopara, joining JEC World to officially launch our platform is an amazing opportunity.”, stated Jean-Pierre Cauchois, CEO Composites Expert.

These training sessions are targeting companies’ employees who would like to improve their expertise, to study professional reconversion, the companies who would like to know more or use composite materials, and universities and school for students to go from theory to practical exercises.

Source:

JEC Group

21.02.2022

EFI’s VUTEk Q5r Printer and Fiery Software earn EDP Awards

Electronics For Imaging, Inc. has received two European Digital Press (EDP) Awards from the European graphics arts trade press, a prestigious technical awards programme that recognises innovative advancements in digital print production. The EFI™ VUTEk® Q5r roll-to-roll UV LED printer beat competition in the large/wide- format printing systems category for printers above 350-centimetres wide. EDP judges honoured EFI Fiery® software integration with finishers as the top solution in the awards programme’s category for software automation tools.

Electronics For Imaging, Inc. has received two European Digital Press (EDP) Awards from the European graphics arts trade press, a prestigious technical awards programme that recognises innovative advancements in digital print production. The EFI™ VUTEk® Q5r roll-to-roll UV LED printer beat competition in the large/wide- format printing systems category for printers above 350-centimetres wide. EDP judges honoured EFI Fiery® software integration with finishers as the top solution in the awards programme’s category for software automation tools.

Automation, quality and value with award-winning roll-to-roll technology
The EFI VUTEk Q5r printer is a roll-to-roll display graphics printer, capable of running at speeds of up to 672 square metres per hour. The 5.2-metre-wide printer delivers a full system solution from file submission to a finished print with options such as in-line quality inspection, in-line slitting and cutting, roll and tape collection, auto-calibration, automated backlit printing, automated blockout printing and much more.
 
EFI VUTEk Q series printers, which include both the Q5r and a 3.5-metre wide VUTEk Q3r model, are available with up to nine colours including white and clear, and feature EFI UltraDrop™ Technology with native 7-picolitre printheads and multi-drop addressability for high-definition quality. Benefits include smoothness in shadows, gradients, and transitions, as well as precise and sharp 3-point size text with a true resolution of up to 1,200 dots per inch.

Fast, flawless finishing
EFI Fiery software integration with finishers, the winner in the EDP Awards category for best software automation tool, offers advanced integration with in-line or offline slitter/cutter/creasers. Operators can define cut, crease, and perforation locations on the job content in the Fiery software solution, which then communicates the configuration to finishing equipment, eliminating operator touchpoints and errors from incompatible layouts.

EFI Fiery software integration with finishers is offered in two different EFI Fiery software products: Fiery Impose and Fiery Finishing Designer.

(c) SHIMA SEIKI MFG., LTD
25.01.2022

SHIMA SEIKI to exhibit at Pitti Filati with flat knitting machine

SHIMA SEIKI ITALIA S.p.A., Italian subsidiary of leading Japanese computerized knitting solutions provider SHIMA SEIKI MFG., LTD., will exhibit at the 90th edition of the Pitti Immagine Filati exhibition in Florence, Italy. Products exhibited will include the N.SVR®123SP computerized flat knitting machine as well as APEXFiz™ design software.

SHIMA SEIKI ITALIA S.p.A., Italian subsidiary of leading Japanese computerized knitting solutions provider SHIMA SEIKI MFG., LTD., will exhibit at the 90th edition of the Pitti Immagine Filati exhibition in Florence, Italy. Products exhibited will include the N.SVR®123SP computerized flat knitting machine as well as APEXFiz™ design software.

The N.SVR®123SP computerized knitting machine features a special loop presser bed, capable of producing hybrid inlay fabrics with both knit and weave characteristics. Demand for such novel fabrics are very high across a wide range of applications, from fashion apparel to sportswear, innerwear, outerwear, uniforms and other functional clothing, as well as home furnishing and technical textiles. Shown in 18G at the SHIMA SEIKI booth, N.SVR®123SP will also feature the special i-Plating option, capable of alternating yarn colors in any pattern, producing jacquard-like designs using plain jersey stitch. Plating can be performed within the same course and for individual needles. In combination with the loop presser and spring-type moveable sinker system even greater diversity in knit design is possible. An SVR®123SP machine in 14G with i-Plating option will also be on display at the booth of yarn spinner IAFIL S.p.A. as well.

APEXFiz™ is subscription-based design software that maintains the proven functions that have made SHIMA SEIKI’s SDS®-ONE APEX series design systems so popular with fashion designers. Installed on personal computers, those strengths are now enhanced with the added versatility to adapt to different work styles and business environments including teleworking and telecommuting. APEXFiz™ software supports the creative side of fashion from planning and design to colorway evaluation, realistic fabric simulation and 3D virtual sampling. Virtual samples are a digitized version of sample making that are accurate enough to be used effectively as prototypes, replacing physical sampling and consequently reducing time, cost and material that otherwise go to waste. APEXFiz™ thereby helps to realize sustainability and digitally transform the fashion supply chain.

APEXFiz™ along with SHIMA SEIKI’s yarnbank™ digital yarn web platform are featured at a special section launched at the previous session of Pitti Filati no. 89 called Pitti Studios. Pitti Studios is a content production service that yarn companies exhibiting at Pitti Filati can use for their own promotion. Yarn companies provide a piece of yarn, which is digitized on yarnbank™ and used to simulate photorealistic fabric on APEXFiz™. This is then processed by a creative studio specializing in digital content to provide static and animated 3D virtual representations. The process shows how to use the latest DX tools to provide accurate representation of a finished garment without having to produce any fabric, converting the conventionally wasteful process of sample-making into a sustainable one.

Continuing from past editions of Pitti Filati are knit samples produced in collaboration with Italian designer Vittorio Branchizio.

Source:

SHIMA SEIKI MFG., LTD

19.01.2022

EFI Connect Conference highlights new Digital Print Innovations

During the 22nd annual Connect conference at the Wynn Las Vegas Resort, Electronics For Imaging, Inc. is highlighting digital print innovations, that give print businesses more capability and profit potential in a range of market applications. Display graphics inkjet offerings at Connect from the company’s leading-edge product portfolio include the new EFI™ Pro 30h production printer. Plus, Connect features the first-ever live demonstration of the new EFI Fiery® FS500 Pro digital front end (DFE) – the most-advanced print server in EFI’s 30+ year history – and the debut of the EFI Fiery Impress™ DFE, a scalable, flexible server and colour management solution for inkjet label and packaging applications as well as for inline manufacturing lines that need variable print.
                                               
EFI Connect has more than 130 break-out sessions presenting the latest tips and trends across all the industry segments EFI supports. This includes sessions addressing the growing analogue-to-digital transformation opportunities using EFI’s industrial Corrugated & Packaging, Textile, and Building Materials/Décor solutions.

During the 22nd annual Connect conference at the Wynn Las Vegas Resort, Electronics For Imaging, Inc. is highlighting digital print innovations, that give print businesses more capability and profit potential in a range of market applications. Display graphics inkjet offerings at Connect from the company’s leading-edge product portfolio include the new EFI™ Pro 30h production printer. Plus, Connect features the first-ever live demonstration of the new EFI Fiery® FS500 Pro digital front end (DFE) – the most-advanced print server in EFI’s 30+ year history – and the debut of the EFI Fiery Impress™ DFE, a scalable, flexible server and colour management solution for inkjet label and packaging applications as well as for inline manufacturing lines that need variable print.
                                               
EFI Connect has more than 130 break-out sessions presenting the latest tips and trends across all the industry segments EFI supports. This includes sessions addressing the growing analogue-to-digital transformation opportunities using EFI’s industrial Corrugated & Packaging, Textile, and Building Materials/Décor solutions.
 
EFI Connect also marks the debut of an innovative prepress product for display graphics businesses, EFI Fiery Prep-it™ software for the preparation, layout, and automated production of print-for-cut jobs. Designed to address productivity needs amid continued labour shortages, this powerful and cost-saving true-shape nesting solution reduces the time needed to nest complex objects for wide-format printing by up to 90%. Compared with competing products, Fiery Prep-it software also reduces media usage by 10% or more, helping to alleviate media supply constraints. With the media savings it generates, this affordable, effective software can pay for itself in four months or less, helping print shops become more competitive.

(c) SHIMA SEIKI
18.01.2022

SHIMA SEIKI opens Online Store for APEXFiz™ Subscriptions

SHIMA SEIKI MFG., LTD. of Wakayama, Japan announces the opening of its new “SHIMA eStore” online shopping site for purchasing subscriptions to its APEXFiz™ design software. Users can access the SHIMA eStore to purchase and download entry-level APEXFiz™ Design Jr. subscription software, or sign up for a free 30-day trial.

SHIMA SEIKI’s APEXFiz™ subscription-based design software has been on sale since March 2021 as the latest addition to its proven SDS®-ONE APEX series design system lineup. Whereas previous APEX-series design systems were offered as an all-in-one proprietary hardware/software package, APEXFiz™ is available as subscription-based design software that can be installed on customers’ individual computers. Maintaining proven functions that have made the APEX series so popular with fashion designers, with APEXFiz™ those strengths are now enhanced with the added versatility to adapt to different work styles and business environments of the “new normal,” including teleworking and telecommuting.

SHIMA SEIKI MFG., LTD. of Wakayama, Japan announces the opening of its new “SHIMA eStore” online shopping site for purchasing subscriptions to its APEXFiz™ design software. Users can access the SHIMA eStore to purchase and download entry-level APEXFiz™ Design Jr. subscription software, or sign up for a free 30-day trial.

SHIMA SEIKI’s APEXFiz™ subscription-based design software has been on sale since March 2021 as the latest addition to its proven SDS®-ONE APEX series design system lineup. Whereas previous APEX-series design systems were offered as an all-in-one proprietary hardware/software package, APEXFiz™ is available as subscription-based design software that can be installed on customers’ individual computers. Maintaining proven functions that have made the APEX series so popular with fashion designers, with APEXFiz™ those strengths are now enhanced with the added versatility to adapt to different work styles and business environments of the “new normal,” including teleworking and telecommuting.

APEXFiz™ offers the latest fashion tech for supporting the creative side of fashion from planning and design to colorway evaluation, realistic fabric simulation and 3D virtual sampling. Virtual samples are a digitized version of sample making that allows visual confirmation of garment designs without the need for producing physical prototypes, reducing time, cost and material that are otherwise wasted. APEXFiz™ thereby helps to realize sustainability while digitally transforming the fashion supply chain.

APEXFiz™ is available in 5 different software variations from APEXFiz™ Design Jr. to APEXFiz™ Design Pro that can be selected according to each customer's needs. APEXFiz™ Design Jr., sold at the SHIMA eStore, is entry-level software that specializes in the design and simulation of woven and flat knitted fabrics for supporting virtual sampling. Fabric simulations are available in different formats to be used together with 3D virtual sampling software besides APEXFiz™, allowing continued use of software already used by customers while enhancing the realism of digital prototypes created on them.

Source:

SHIMA SEIKI

05.01.2022

EFI announced to accelerate investment into its Inkjet and Fiery business units

Electronics For Imaging, Inc. is announcing that it will be prioritizing technology investments to accelerate growth in its fast-growing industrial EFI™ Inkjet business to continue to be a leader in the industry of analog-to-digital transition, as well as in its market-leading Fiery® business. As part of this focused strategy, EFI has completed a sale of its eProductivity Software (“EPS”) packaging and print productivity software business to an affiliate of Symphony Technology Group (“STG”). EFI and EPS will continue to collaborate with their joint customers and partners to ensure mutual success.

This realignment allows EFI to accelerate investment into its Inkjet and Fiery business units to capitalize on the growth opportunities available in existing segments the company serves, as well as drive expansion into markets that are beginning the transformation toward digital.

Electronics For Imaging, Inc. is announcing that it will be prioritizing technology investments to accelerate growth in its fast-growing industrial EFI™ Inkjet business to continue to be a leader in the industry of analog-to-digital transition, as well as in its market-leading Fiery® business. As part of this focused strategy, EFI has completed a sale of its eProductivity Software (“EPS”) packaging and print productivity software business to an affiliate of Symphony Technology Group (“STG”). EFI and EPS will continue to collaborate with their joint customers and partners to ensure mutual success.

This realignment allows EFI to accelerate investment into its Inkjet and Fiery business units to capitalize on the growth opportunities available in existing segments the company serves, as well as drive expansion into markets that are beginning the transformation toward digital.

Industrial Inkjet: Capturing Unprecedented Opportunity
The industrial inkjet space is ripe with opportunity in existing and adjacent vertical markets. EFI Inkjet will continue to drive in high-volume, shuttle and single-pass inkjet technology, which the company has currently implemented in award-winning, high-performance products for the Packaging & Corrugated, Display Graphics, Textile, and Building Materials/Decor verticals. EFI will also leverage its industry-leading expertise in hardware, mechanical control software, high-speed electronics, services, cloud-connected devices, and ink innovations to deliver the next generation of versatile, high-volume, superior-quality printers and presses.
 
Following the realignment, EFI is making investments in R&D to strengthen its position in core markets while entering new categories – including the development of technologies to address new applications for the textile space and for packaging.

Fiery: Driving Digital Print Innovation and Growth
The Fiery business unit, under the continued leadership of Fiery Chief Operating Officer and General Manager Toby Weiss, remains as one of the world’s premier DFE providers, enabling the high performance required across many vertical markets including packaging, signage and commercial print with advanced Fiery solutions driving high-end printers and presses from many major equipment manufacturers.

Productivity Software: Investing for Growth under New Ownership
EPS’ new owner, STG, is a private equity firm that focuses on investing in software, data analytics, and software-enabled technology services companies, and will support EPS to deliver enhanced value to its packaging and print customers and accelerate global growth. STG completed this acquisition on December 30, 2021. The price and terms of the deal were not disclosed.
 
Moelis & Company LLC served as exclusive financial advisor, and Sidley Austin LLP acted as legal counsel, to EFI in the sale of EPS. Paul Hastings LLP acted as legal advisor to STG.
 
EFI’s upcoming Connect users conference will be a joint event for EFI and EPS customers. Leaders from both companies will highlight their technology enhancements and product roadmap strategies during the January 17-21 Las Vegas gathering.

Source:

EFI

20.12.2021

EFI: New Innovations in Digital Textile at EFI Reggiani Open House

During an expansive, three-day Electronics For Imaging, Inc. open house this month at the company’s EFI™ Reggiani industrial textile printer facility, textile and apparel manufacturers witnessed first-hand the market-leading innovations that provide users with new opportunities. The December open house, which drew more than 70 attendees from over 23 different European, South American, and Middle Eastern countries, featured informative sessions with product experts on a diverse range of topics, covering new and trending market applications for textile manufacturers.

Attendees witnessed live demonstrations of eight advanced digital printers during the open house, including the new EFI Reggiani HYPER, EFI Reggiani TERRA Silver scanning/multi-pass printer, and EFI Reggiani BLAZE as well as the EFI Reggiani BOLT – the award-winning single-pass offering that is the one of the fastest digital textile printers.

During an expansive, three-day Electronics For Imaging, Inc. open house this month at the company’s EFI™ Reggiani industrial textile printer facility, textile and apparel manufacturers witnessed first-hand the market-leading innovations that provide users with new opportunities. The December open house, which drew more than 70 attendees from over 23 different European, South American, and Middle Eastern countries, featured informative sessions with product experts on a diverse range of topics, covering new and trending market applications for textile manufacturers.

Attendees witnessed live demonstrations of eight advanced digital printers during the open house, including the new EFI Reggiani HYPER, EFI Reggiani TERRA Silver scanning/multi-pass printer, and EFI Reggiani BLAZE as well as the EFI Reggiani BOLT – the award-winning single-pass offering that is the one of the fastest digital textile printers.

EFI Reggiani HYPER – a fast scanning digital printer
The new EFI Reggiani HYPER is a scanning printer available in 1.8-metre, 2.4-metre or 3.4-metre widths. The Reggiani HYPER model targets the industrial high-speed segment of the multi-pass textile printing sector.

With an up to eight-colour configuration, it prints at speeds up to 13 linear metres per minute in two-pass production mode. The new printer is suitable for high-quality production on knitted or woven fabrics and is designed with smart technology that enables it to be integrated into Industry 4.0 projects.

Sustainable direct-to-textile printing with the EFI Reggiani TERRA Silver
The new-version TERRA Silver printer is part of EFI’s complete TERRA line-up of pigment ink printer solutions. It allows print service providers to enter the world of industrial textile with a short, smart and green production process.
The printer also features:

  • A new recirculating ink system for superior reliability and minimum maintenance
  • Several printing modes to ensure maximum flexibility in terms of design capability
  • New, real-time image processing that eliminates time spent in image pre-calculations
  • A user friendly, intuitive interface
  • A more-efficient polymerisation process that takes place as printed textile goes through the printer’s on-board dryer.

EFI Reggiani BLAZE, an ideal entry solution for industrial textile printing
The EFI Reggiani BLAZE printer is designed to give textile companies the opportunity to enter the digital textile printing market with a compact solution. The new, 1.8-metre-wide printer offers an innovative, low-maintenance, continuous recirculation ink system equipped with a level sensor and degassing as well as a print head crash protective system for longer printhead life and superior uptime.

The upgraded EFI Reggiani BOLT – one of the fastest digital textile printers
In 2021, the EFI Reggiani BOLT received a combination of hardware and software enhancements that minimise artifacts, compensating for missing nozzles that may occur over time and enhancing uniformity to deliver smoother solid colours. The upgrade also delivers improved quality and smoother gradients, plus it enables faster printhead replacement and drastically increases file processing speed by up to 200% for large, complex files.

Source:

EFI GmbH

(c) AMUT/EREMA
02.12.2021

AMUT/EREMA: From PET bottles straight to food contact grade r-PET packaging

AMUT’s strategic partnership with EREMA contributes to accelerate the transition towards a greener world.  In summer 2021, EREMA in collaboration with AMUT  has finalized the installation and commissioning of ALTO packaging ́s first extrusion line for food grade PET sheets in New Zealand market. At the ALTO Plastic Packaging site, in Albany, the plant now processes 100 % washed post-
consumer flakes into 100 % food contact grade monolayer thermoforming sheet. In New Zealand, this milestone represents the first system to be installed for this special application.

The plastic packaging company ALTO, a division of PACT Group, invested for this new food grade PET sheet extrusion line as a part of Pact Group ́s vision to lead Circular Economy through Packaging in Australia and New Zealand.

AMUT’s strategic partnership with EREMA contributes to accelerate the transition towards a greener world.  In summer 2021, EREMA in collaboration with AMUT  has finalized the installation and commissioning of ALTO packaging ́s first extrusion line for food grade PET sheets in New Zealand market. At the ALTO Plastic Packaging site, in Albany, the plant now processes 100 % washed post-
consumer flakes into 100 % food contact grade monolayer thermoforming sheet. In New Zealand, this milestone represents the first system to be installed for this special application.

The plastic packaging company ALTO, a division of PACT Group, invested for this new food grade PET sheet extrusion line as a part of Pact Group ́s vision to lead Circular Economy through Packaging in Australia and New Zealand.

Thanks to the direct combination of VACUREMA® PET recycling technology and the AMUT Inline Sheet production technology there is no longer any extra process stage. This is, because the melt goes straight from the VACUREMA® 1716 T Basic to the AMUT plant without the detour of pelletising. The post-consumer PET material is already decontaminated and pre-dried prior to extrusion in the vacuum reactor of the VACUREMA® Basic, with a throughput of up to 1,500 kg per hour. After high capacity filtration by EREMA SW-RTF backflush filter and online IV measurement, the melt goes directly into the AMUT Inline Sheet plant where it is processed into thermoforming sheet from 0.15 mm till 1.2 mm thickness. The monolayer thermoforming sheet produced from pure rPET is not only 100 % food contact compliant, it also fulfils the FDA and further regulations. At ALTO it is further processed into trays and food containers.

AMUT played its part by providing a full range of downstream equipment ranging from the Automatic Tdie, three rolls stack calender with automatic gap control and motorized cross axing unit, lamination unit for welding and barrier films, thickness control gauge to anti-static silicon coating unit, fully automatic two shafts turret winder and in line edge trims grinding and recycling.

The special features of this extrusion line come from the complete automatic and easy management of the line. This is due to the new Amut`s software including the Easy Start and Easy Change functions that will allow the operator to start the extrusion line and change product formats in automatic mode.

EREMA and AMUT are long-term partners in the Inline Sheet sector. EREMA ́s VACUREMA® technology is currently in use in more than 100 Inline Sheet facilities around the world, also for PACT Group companies in Australia. 

More information:
AMUT EREMA PET plastics Recycling
Source:

EREMA Group GmbH