From the Sector

The DITF is leading the joint project "DACCUS-Pre*". The basic idea of the project is to develop a new building material that stores carbon in the long term and removes more CO₂ from the atmosphere than is emitted during its production.       

In collaboration with the company TechnoCarbon Technologies, the project is now well advanced - a first demonstrator in the form of a house wall element has been realized. It consists of three materials: Natural stone, carbon fibers and biochar. Each component contributes in a different way to the negative CO₂ balance of the material:

Two slabs of natural stone form the exposed walls of the wall element. The mechanical processing of the material, i.e. sawing in stone cutting machines, produces significant quantities of stone dust. This is very reactive due to its large specific surface area. Silicate weathering of the rock dust permanently binds a large amount of CO₂ from the atmosphere.

Carbon fibers in the form of technical fabrics reinforce the side walls of the wall elements. They absorb tensile forces and are intended to stabilize the building material in the same way as reinforcing steel in concrete. The carbon fibers used are bio-based, produced from biomass. Lignin-based carbon fibers, which have long been technically optimized at DITF Denkendorf, are particularly suitable for this application: They are inexpensive due to low raw material costs and have a high carbon yield. In addition, unlike reinforcing steel, they are not susceptible to oxidation and therefore last much longer. Although carbon fibers are more energy-intensive to produce than steel, as used in reinforced concrete, only a small amount is needed for use in building materials. As a result, the energy and CO₂ balance is much better than for reinforced concrete. By using solar heat and biomass to produce the carbon fibers and the weathering of the stone dust, the CO₂ balance of the new building material is actually negative, making it possible to construct CO₂-negative buildings.

The third component of the new building material is biochar. This is used as a filler between the two rock slabs. The char acts as an effective insulating material. It is also a permanent source of CO₂ storage, which plays a significant role in the CO₂ balance of the entire wall element.

From a technical point of view, the already realized demonstrator, a wall element for structural engineering, is well developed. The natural stone used is a gabbro from India, which has a high-quality appearance and is suitable for high loads. This has been proven in load tests.  Bio-based carbon fibers serve as the top layer of the stone slabs. The biochar from Convoris GmbH is characterized by particularly good thermal insulation values.

The CO₂ balance of a house wall made of the new material has been calculated and compared with that of conventional reinforced concrete. This results in a difference in the CO₂ balance of 157 CO₂ equivalents per square meter of house wall. A significant saving!

* (Methods for removing atmospheric carbon dioxide (Carbon Dioxide Removal) by Direct Air Carbon Capture, Utilization and Sustainable Storage after Use (DACCUS).

Lightweight design is a key enabler for addressing the energy transition and sustainable economy. Following the liquidation of the state agency Leichtbau BW GmbH, a consortium consisting of the Allianz Faserbasierter Werkstoffe Baden-Württtemberg (AFBW), the Leichtbauzentrum Baden-Württemberg (LBZ e.V. -BW) and Composites United Baden-Württemberg (CU BW) now represents the interests of the lightweight construction community in the State.

The Lightweight Design Agency for Baden-Württemberg is set up for this purpose on behalf of and with the support of the State. The Lightweight Construction Alliance BW is the central point of contact for all players in the field of lightweight construction in the State and acts in their interests at national and international level. Professor Markus Milwich from the German Institutes of Textile and Fiber Research Denkendorf (DITF) represents the agency.

The use of lightweight materials in combination with new production technologies will significantly reduce energy consumption in transportation, the manufacturing industry and the construction sector. Resources can be saved through the use of new materials. As a cross-functional technology, lightweight construction covers entire value chain from production and use to recycling and reuse.

The aim of the state government is to establish Baden-Württemberg as a leading provider of innovative lightweight construction technologies in order to strengthen the local economy and secure high-quality jobs.

Among others, the "Lightweight Construction Alliance Baden-Württemberg" will continue the nationally renowned "Lightweight Construction Day", which acts as an important source of inspiration for a wide range of lightweight construction topics among business and scientific community.

Professor Milwich, an expert with many years of experience and an excellent network beyond the State's borders, has been recruited for this task. In his role, Milwich also represents the state of Baden-Württemberg on the Strategy Advisory Board of the Lightweight Construction Initiative of the Federal Ministry for Economic Affairs and Climate Action, which supports the cross functional-technology and efficient transfer of knowledge between the various nationwide players in lightweight construction and serves as a central point of contact for entrepreneurs nationwide for all relevant questions.

From 2005 to 2020, Professor Milwich headed the Composite Technology research at the DITF, which was integrated into the Competence Center Polymers and Fiber Composites in 2020. He is also an honorary professor at Reutlingen University, where he teaches hybrid materials and composites. "Lightweight design is an essential aspect for sustainability, environmental and resource conservation. I always showcase this in research and teaching and now also as a representative of the lightweight construction community in Baden-Württemberg," emphasizes Professor Milwich.

In a move to enhance the global competitiveness of the Turkish apparel industry, the Istanbul Apparel Exporters' Association (IHKIB) has entered into a collaborative agreement with the Worldwide Responsible Accredited Production (WRAP).

IHKIB, representing 80% of Türkiye's apparel exports, aims to facilitate and guide its members in navigating new markets and staying abreast of sectoral developments.
WRAP, a US-based non-profit organization, focuses on promoting safe, lawful, humane, and ethical working conditions within the textile and apparel industry.

Mr. Selcuk Mehmet Kaya, Chairman of the International Relations and Sustainability Committee of IHKIB, and Mr. Avedis Seferian, President and CEO of WRAP, officially inked a collaboration agreement on March 8, 2024, marking a significant step towards fostering business relations between Türkiye and the USA. The agreement focuses on a pilot project developed by IHKIB and WRAP, aiming to identify leading Turkish apparel companies exporting to the USA and encouraging these facilities to attain WRAP certification. In return, WRAP will provide in-person and virtual training at no charge to guide these facilities through the certification process. The project seeks to strengthen business ties between Türkiye and the USA, creating additional opportunities for mutual cooperation between the parties in both countries.

Freudenberg Performance Materials (Freudenberg) is showcasing solutions for the automotive, building, apparel, filtration and packaging industries at this year’s Techtextil in Frankfurt am Main from April 23 – 26.

Sustainable nonwoven for car seats
One innovation highlight at Techtextil is a novel Polyester nonwoven material for car seat padding. Also available as a nonwoven composite with PU foam, it is not only easier for car seat manufacturers to handle during the mounting process, but also ensures better dimensional stability as well as providing soft and flexible padding. It has a minimum 25 percent recycled content, for example, by reusing nonwoven clippings and waste, and is fully recyclable. Full supply chain transparency enables customers to trace and verify the content of the nonwoven and thus ensures a responsible production process. The Freudenberg experts will also be presenting several other nonwoven solutions made of up to 80 percent recycled materials that can be used in car seat manufacturing.

Biocarrier for green roofs
Freudenberg is showcasing a sustainable carrier material for green roofs on urban buildings at the trade fair. The carrier is made from polylactide, i.e. from renewable resources. When filled with soil, it provides a strong foothold to root systems, enabling the growth of lightweight sedum blankets that can be rolled out to provide instant green roofs. These roofs not only help counter urban heat, they also improve stormwater management and regulate indoor temperatures.

From textile waste to padding
The company extended its circular thermal wadding product range with the release of comfortemp® HO 80xR circular, a wadding made from 70 percent recycled polyamide from discarded fishing nets, carpet flooring and industrial plastic. Because polyamide 6, also known as nylon, retains its performance characteristics after multiple recycling processes, the fibers can be used again and again to manufacture performance sporting apparel, leisurewear and luxury garments.

Packaging solutions with various sustainability benefits
Freudenberg is also showcasing products for sustainable packaging and filtration solutions. The long-lasting Evolon® technical packaging series is a substitute for disposable packaging used in the transport of sensitive industrial items such as automotive parts. The material is made from up to 85 percent recycled PET. A further highlight at Techtextil are Freudenberg’s fully bio-based solutions for manufacturing dessicant bags. The binder-free material based on bio-fibers is also industrially compostable.
In addition, the experts will be giving trade fair visitors an insight into Freudenberg’s filtration portfolio.

Turkey's leading garment machinery manufacturers and representatives have collaborated with Teknik Fuarcılık for GarmentTech İstanbul Garment, Embroidery Machines Spare Parts and Sub Industry Exhibition to host the first GarmentTech İstanbul Exhibition.

The GarmentTech İstanbul Exhibition will be held at İstanbul Expo Center (IFM) between June 25-28, 2025 and brings together all the technologies used in garment and ready-to-wear production.

The ready-to-wear and garment sector is among the locomotive sectors of the Turkish economy with both employment and export income. With 22 thousand 640 exporters and 42 thousand 434 manufacturers, the sector is among the priority sectors in the country's employment with approximately 700 thousand people working in production. Together with the retail and ready-to-wear sectors, total employment exceeds 2 million.

On the other hand, ready-to-wear and garment sector is the 3rd largest exporter in Turkey. Turkey is the 5th country in the world that exports the most ready-to-wear and garment. In 2023, the sector reached 19.3 billion dollars in exports and has a share of 7.5% in general exports.

Teknik Fuarcılık, which has more than 30 years of experience in exhibition organization and has made the ITM International Textile Machinery Exhibition a world brand, has taken action to make the success achieved by the garment and ready-to-wear sector sustainable. GarmentTech İstanbul Exhibition, which will be organized with the support of the members of the Garment Machinery Advisory Board and in cooperation with the Apparel Automation and Machinery Manufacturers Association (KOMİD), will host professional visitors and global buyers from all over the world.

The press conference of GarmentTech İstanbul Exhibition was attended by members of the Garment Machinery Advisory Board, Vice Chairman of Astaş Holding H. Kaya Aşçı, Astaş Juki Board Member and General Manager Turgay Aşçı, Chairman of the Board of Çatma Makine Yavuz Çatma, Chairman of the Board of Alba Makine Cengiz Albayrak, General Manager of Malkan Makine Alparslan Er, General Manager of Uğur Makine Temel Kamiloğlu, Tetaş Sales and Marketing Assistant General Manager Murat Eren, Malkan Makina Factory Manager Metin Kılıç and KOMID President Haluk Akın, TEMSAD President Adil Nalbant, KOMİD Members Serkon Makina Chairman İzzet Savaş, Robotech General Manager Hüseyin Çetin, Chairman of the Board of NewTech Machinery Nezir Yazıcı, LGM Foreign Trade Specialist Yiğit Sağdık Manav, Avtek Manager Oğuz Avcı and many sector representatives.

Mayer & Cie. CN Changzhou LLC, the Chinese subsidiary of the German circular knitting and braiding machine manufacturer Mayer & Cie., settled in Jiangsu Province at the beginning of the year. Until now, the Sales & Service subsidiary Mayer & Cie. China, founded in 2003 and later to become Mayer & Cie. China, had been based in Shanghai.

The new location within a Sino-German Innovation Park comprises a production hall of around 5,000 square meters. In the future, the circular knitting machines assembled for the domestic market will increasingly consist of locally sourced parts and components from various suppliers.

Since 2011, Mayer & Cie. has been assembling selected machine types for the domestic market at its Chinese plant in Shanghai. It started with a single jersey machine for the most common requirements. Today, China's domestic portfolio includes four types of machines. Until now, the knitting heads for these circular knitting machines had been pre-produced at the Mayer & Cie. plant in the Czech Republic and then transported to China.

The manufacturer is now saying goodbye to this "knitting head principle". It made perfect sense for the start of the assembly line, says Benjamin Mayer, managing partner of Mayer & Cie. However, it leaves little room for flexibility. He explains: "In the future, we will source all parts and components of the machines assembled in China from various local suppliers. This allows us to offer our local customers more attractive prices and faster delivery times with the same quality standards. We expect this change to improve the positioning of our products in the domestic market." In addition, the new plant will be connected to the parent company in Albstadt via an SAP connection. This was imperative to increase efficiency, transparency and quality.

The new headquarters of Mayer & Cie. CN is the German Chinese Innovation Park in Jintan in Jiangsu Province. The companies based there enjoy various advantages, including attractive location costs as well as proximity and exchange with other German companies on site. In addition, the administration of the SGIP supports companies in their search for employees, suppliers and service providers.

On March 6, 2024, Rieter received an order for the first batch of Rieter technology amounting to around CHF 62 million from Shanghai Digital Intelligence World Industrial Technology Group Co., Ltd. (DIW). Rieter also signed a strategic partnership with DIW to develop an intelligent yarn manufacturing technology that utilizes digitization and automation to minimize conversion costs.

Rieter and DIW signed a first order in the amount of around CHF 62 million for combers and draw frames that will provide the basis to transform DIW’s spinning mills into state-of-the-art industrial textile operations. DIW, a fast-growing company specializing in intelligent manufacturing and industrial operation services, selected Rieter following a competition in which the company’s machines achieved better stability and higher production than competitors. The strategic partnership of DIW and Rieter is designed to further enhance the overall operational efficiency of DIW’s mills by providing highly efficient machines, automation and digitization technology. This will also minimize conversion cost and consolidate the sustainable growth of both companies, while contributing to the high-quality development of the Chinese textile industry.

Archroma and Browzwear, a company of 3D digital solutions for the fashion industry, have expanded their partnership to bring the complete Color Atlas by Archroma® library of colors to Browzwear’s VSticher, Lotta and Stylezone platforms.

Designers will now have access to a total of 5,760 color references, with 1,440 colors for polyester added to Browzwear’s existing color library of 4,320 Color Atlas colors for cotton poplin. This will support them to collaborate across the entire supply chain, ensuring color consistency from digital design to production for cotton, polyester and blends.

Crucially, the color references in the Color Atlas by Archroma® have been formulated to comply with leading international eco-standards, allowing designers to select dyes and finishes that meet their desired sustainability profile. Each color is available as a physical color standard that includes precise dyeing recipes and compliance data, as well as access to expert technical support from Archroma around the world.

The German Institutes of Textile and Fiber Research Denkendorf (DITF) have modernized and expanded their melt spinning pilot plant with support from the State of Baden-Württemberg. The new facility enables research into new spinning processes, fiber functionalization and sustainable fibers made from biodegradable and bio-based polymers.

In the field of melt spinning, the DITF are working on several pioneering research areas, for example the development of various fibers for medical implants or fibers made from polylactide, a sustainable bio-based polyester. Other focal points include the development of flame-retardant polyamides and their processing into fibers for carpet and automotive applications as well as the development of carbon fibers from melt-spun precursors. The development of a bio-based alternative to petroleum-based polyethylene terephthalate (PET) fibers into polyethylene furanoate (PEF) fibers is also new. Bicomponent spinning technology, in which the fibers can be produced from two different components, plays a particularly important role, too.

Since polyamide (PA) and many other polymers were developed more than 85 years ago, various melt-spun fibers have revolutionized the textile world. In the field of technical textiles, they can have on a variety of functions: depending on their exact composition, they can for example be electrically conductive or luminescent. They can also show antimicrobial properties and be flame-retardant. They are suitable for lightweight construction, for medical applications or for insulating buildings.

In order to protect the environment and resources, the use of bio-based fibers will be increased in the future with a special focus on easy-to-recycle fibers. To this end, the DITF are conducting research into sustainable polyamides, polyesters and polyolefins as well as many other polymers. Many 'classic', that is, petroleum-based polymers cannot or only insufficiently be broken down into their components or recycled directly after use. An important goal of new research work is therefore to further establish systematic recycling methods to produce fibers of the highest possible quality.

For these forward-looking tasks, a bicomponent spinning plant from Oerlikon Neumag was set up and commissioned on an industrial scale at the DITF in January. The BCF process (bulk continuous filaments) allows special bundling, bulking and processing of the (multifilament) fibers. This process enables the large-scale synthesis of carpet yarns as well as staple fiber production, a unique feature in a public research institute. The system is supplemented by a so-called spinline rheometer. This allows a range of measurement-specific chemical and physical data to be recorded online and inline, which will contribute to a better understanding of fiber formation. In addition, a new compounder will be used for the development of functionalized polymers and for the energy-saving thermomechanical recycling of textile waste.

Texhibition Istanbul Fabric and Textile Accessories Fair, organised by İTKİB Fuarcılık A.Ş. in cooperation with the Istanbul Textile Exporters Association (İTHİB), is ready for its fifth edition. From 6 to 8 March 2024, 558 exhibitors will present themselves to the 30,000 expected visitors from over 100 countries, including the European Union, Great Britain, the USA, North Africa and the Middle East. With this edition, Texhibition has more than doubled the space compared to the last event to 35,000 square metres.

The fifth edition of Texhibition Istanbul offers a comprehensive overview of all product groups in the textile prepress sector: from woven fabrics to knitwear, from denim to artificial leather and textile accessories

Due to popular demand, the fair has been expanded to five halls, including the new Yarn Hall (Hall 8) with exhibitors such as Sasa, Aksa, Karafiber, Kortex, Tepar, Ensar, Kaplanlar and Iskur and the BlueBlack Denim Hall (Hall 7), which showcases the latest denim trends and presents a wide range from blue shades to black denims with exhibitors such as İsko, Çalık Bossa, Kipas and İskur. BlueBlack Denim is designed by the  designer Idil Tarzi in cooperation with the creative directors Gönül Altunisik and Selvi Yigci.

Curated by Idil Tarzi and her creative team, the Texhibition Trend Area in Halls 4 and 5 presents the latest colour trends, materials and accessories.

Under the direction of designers Arzu Kaprol and Filiz Tunca, the Innovation Hub showcases technological innovations that add value to textile production: from fibre to yarn, from fabrics to clothing.

Digital art installations in the entrance area, which run through the entire trade fair, as well as piano performances in the foyer await visitors at the upcoming Texhibition.

Seminars and workshops with industry experts shed light on current topics in the industry, including innovations, production processes and design developments. These opportunities offer participants a platform to exchange knowledge and discuss the latest developments in the textile industry.