From the Sector

Adaptable insulation elements can ensure that the heat transfer through the building envelope can be adjusted as required. This saves heating or cooling energy and therefore costs. Intelligent systems can regulate heat transfer according to the outside temperature and the need for heating or cooling in the interior. In the ReVaD project, the German Institutes of Textile and Fiber Research Denkendorf (DITF) and their partners are developing adaptive building envelopes that can also use concrete components as structural thermal energy storage units for temperature control in buildings.

The research project is developing adaptable insulation elements based on the Knudsen effect. The Knudsen effect describes the change in the thermal conductivity of porous structures with the prevailing gas pressure in the pore space. If there is a vacuum in the pore space, the thermal conductivity is low; if the pressure increases, the thermal conductivity also increases. In order to use the principle in an adjustable insulation element, the highest possible switching factor between the two states is required. To achieve this, the pore system and gas pressure range must be optimally matched. In the adaptable insulation panel, the pore system consists of a spacer fabric that is being developed at the DITF. A key challenge here is the compressive strength of the filling core, which must only allow minimal deformation at a surface pressure of 10 N/cm2 imprinted by a fine vacuum.

The research team at the Technology Center Knitting Technique at DITF has developed the corresponding pressure-resistant structures. Their pore size will be optimized in the next steps by inserting textured yarns into the pole thread space. The basic thermal conductivity of the structure should be increased as little as possible. With the knitted structures in the panel, a switching factor, i.e. the ratio of maximum to minimum thermal conductivity achieved, of 5 has already been demonstrated. Current work involves optimizing the spacer structures and setting up a demonstrator.

In the joint project, the Institute of Technical Thermodynamics at the German Aerospace Center (DLR) in Stuttgart is developing a thermochemical reactor component that enables precise and energy-efficient gas pressure adjustment in the vacuum insulation panel. Metal hydride-hydrogen reaction systems are used, which allow the gas pressure in the insulation panel to be set through temperature control.

The Institute for Building Energetics, Thermal Engineering and Energy Storage (IGTE) at the University of Stuttgart is investigating the integration possibilities of the panels in the wall composite using simulations and experiments. The thermal-energetic simulations make it possible to assess the energy-saving potential of the technology in different scenarios and under different boundary conditions. A demonstrator is used to test the adaptable thermal insulation in an application-oriented manner.

The ReVaD project (development of adaptable vacuum insulation elements for the needs-based adaptation of heat transfer in building envelopes and structures as well as the thermal activation of storage masses) is funded by the Federal Ministry of Economics and Energy as part of joint industrial research (IGF) (FKZ: 22617 N).

Leading computerized flat knitting innovator SHIMA SEIKI MFG., LTD. of Wakayama, Japan is collaborating with Lonati S.p.A. of Brescia, Italy to promote digitalization and sustainable product development within the sock industry.

The partnership forms a synergy by leveraging software solutions offered by each company—APEXFiz® design software developed and sold by SHIMA SEIKI and ORION programming software developed and sold by Lonati. Together, they aim to help the industry shed ist dependence on traditional physical sample creation processes.

In the fashion industry, particularly in the sock sector, it is common practice to create physical samples for design consideration and production decisions. However, this process presents numerous challenges, including waste of resources and labor, economic burdens such as sampling costs and material expenses, as well as delays due to lead times before market launch.

To address these challenges, “3D Virtual Sampling” has gained attention as an effective method. This approach allows for design consideration without physical samples and enables rapid and efficient prototyping. As a result, companies can significantly reduce costs and time while minimizing their environmental impact. Additionally, developing products that meet market needs enhances competitiveness.

SHIMA SEIKI’s APEXFiz® is design software that is available with 3D virtual sampling capabilities for knitted products and has been adopted by many companies in the sock industry to high acclaim. By using this tool, designers can visualize sock designs in real-time and receive quick feedback. Moreover, specialized software dedicated to sock design—APEXFiz® Design-Sox—is in the works for future release. Meanwhile, ORION is Lonati's innovative programming software that is part of the UNLIMITEX® suite, and allows users to proactively verify data in 3D from a technical perspective, identifying and resolving potential issues in advance at each stage from programming to manufacturing. ORION and APEXFiz® Design-Sox are both scheduled for release in June of 2025.

Together, APEXFiz® and ORION further streamline virtual sampling by integrating the workflow from design to production. This integrated process enables companies to shorten time-to-market while efficiently delivering high-quality products. The innovative workflow developed through the partnership between SHIMA SEIKI and Lonati are set to revolutionize the sock industry and serve as a key driver for creating new business opportunities and competitive advantage.

The winners of the 2025 IDEA® Achievement Awards and FiltXPO™ Innovation Awards were announced during special ceremonies held April 29 and 30 at the Miami Beach Convention Center in Miami Beach, Florida. Presented at the co-located IDEA®25 and FiltXPO™ 2025 events, the awards celebrate outstanding innovations driving progress in nonwovens and filtration. INDA, the Association of the Nonwoven Fabrics Industry, collaborated with International Filtration News for the FiltXPO™ Awards and Nonwovens Industry magazine for the IDEA® Achievement Awards.

IDEA® Equipment Achievement Award
Dilo Systems GmbH – MicroPunch
The rising energy costs and water shortages have led to a re-evaluation of production methods, with a stronger focus on environmental impact. With MicroPunch, it is possible to reduce energy consumption by approximately 75 percent compared with other consolidation techniques that produce lightweight nonwovens. This technology enhances efficiency and reduces the manufacturing costs and the environmental footprint.

IDEA® Nonwoven Products Achievement Award
Innovatec Microfibre Technology GmbH & Co. KG – InnovaWipe® Water-Soluble Nonwoven
This water-soluble nonwoven is completely biodegradable under both aerobic and anaerobic conditions. It offers excellent resistance to oils, greases and chemicals. It does not leave any microplastics behind, breaking down into carbon dioxide, water and biomass. It also has no ecotoxic effects, is safe for the marine environment and does not cause fatbergs or blockages in wastewater systems – flushable and home compostable.

IDEA® Raw Materials Achievement Award
Woolchemy NZ Ltd. – neweFibre
Woolchemy’s neweFibre is the world’s first hygiene-grade wool, engineered for high-performance, sustainable hygiene products. This fully traceable, renewable fiber enhances moisture management, thermal comfort, and odor control. Seamlessly integrating into production, neweFibre powers innovations like neweFlex ADL for exceptional fluid distribution and skin dryness.

IDEA® Short-life Achievement Award
Egal Pads, Inc. – Egal™ Pads on a Roll
At Egal, we believe pads should be as common as toilet paper.  Our vision is that “pads on a roll” will be put in every toilet stall – where they are needed most – to ensure privacy and dignity to all who menstruate.  Egal pads are manufactured in roll form, 40 individually wrapped on each roll, so they can be mounted on existing toilet paper dispensers or in Egal’s custom-designed dispensers.

IDEA® Long-life Achievement Award
Magnera – Sontara® EcoRE Bag
EcoRE bags are produced entirely from cellulosic fibers, presenting a sustainable alternative to traditional synthetic materials. Made with Sontara fabric certified by OK compost HOME, these bags maintain their durability and strength without the need for added binders, addressing a common concern with compostable goods. With plastic bag bans now in place in many states, Sontara offers a timely and eco-friendly solution for the retail and shopping market.

IDEA® Sustainability Advancement Award
KINDCLOTH™ – PURA HEALTH Insect Repellent – Water Dissolvable Wipes
This wet wipe combines water-dissolvable Hydropol™ technology with a natural formula featuring lemongrass and citronella. Designed for eco-conscious consumers, this innovative wipe provides effective insect protection while leaving no waste behind. Certified biodegradable, flushable, and designed not to create harmful microplastics, it safeguards fragile ecosystems and supports sustainability goals.

IDEA® Entrepreneur Award
Dude Products, Inc.
In less than a decade, the Dude Wipes brand has grown from an entrepreneurial concept conceived in a bachelor’s post-college apartment to a more than $200 million global brand. These flushable wipes have flourished in flushable wipes industry, successfully going head to head against multinational consumer product companies Kimberly-Clark, S.C. Johnson, and Procter & Gamble.

FiltXPO Air/Gas Filtration Award
Greentech Environmental LLC – Greentech Filters with ODOGard®
ODOGard® technology deeply integrates odor-neutralizing polymers into nonwoven and nanofiber filters, offering an innovative, non-toxic approach to indoor air quality. ODOGard® significantly enhances filtration durability and performance.

FiltXPO Water/Liquid Filtration Award
Ahlstrom – BioProtect™
Ahlstrom’s sustainable BioProtect™ material offers superior dye-catching performance for laundry applications. Manufactured from 100 percent naturally derived fibers and OC-Biobinder®, BioProtect™ is both biobased and home compostable, combining premium performance with environmental responsibility.

FiltXPO Filtration Equipment Award
Filtration Advice Inc. – FA-TCO Software
This cutting-edge software provides comprehensive Total Cost of Ownership (TCO) analysis and predictive modeling for air filtration systems. FA-TCO enables data-driven decisions, extending filter lifespans, reducing operational costs, and enhancing overall sustainability in filtration management.

Mimaki Europe, a leading provider of industrial inkjet printers and cutting plotters, has unveiled its new vision, structure and go-to-market strategy against a backdrop of new product innovations making their debut at FESPA Global Print Expo 2025.

Mimaki’s new technology and pioneering ink products represent over half of the company’s product line-up being demonstrated live on its FESPA stand. These latest solutions include the new Mimaki UJV300DTF-75 Printer, which leverages Mimaki’s UV printing expertise to deliver a reliable solution for object decoration, enabling high-quality, durable prints on surfaces that were previously unsuitable for direct UV printing.

Launched last week, the new Mimaki ELH and ELS inks are also being showcased for the very first time. These sustainable inks deliver the same high-standard functionality as equivalent Mimaki inks but have been formulated to be completely free of SVHC and, uniquely, CMR, therefore reducing the impact on human health and the environment.

Two new printers, the JV200-160 and Tx330-1800, will make their debut in EMEA. An easy-to-use roll-to-roll printer, the JV200-160 uses eco-solvent inks and offers reliable signage production with outstanding print quality. Created for the textile and apparel markets, the Tx330-1800 is equipped with a dual ink set capability to seamlessly switch between textile pigment inks and dye sublimation inks for a more diverse range of applications in one machine.

As Mimaki kicks off this innovation-packed FESPA, the company officially announces Arjen Evertse’s promotion to Director Sales, along with the landmark news that he is the first locally appointed member to join the Mimaki Europe Board of Directors.

Mimaki Europe will implement a new strategy that enables further ‘horizontal growth’, as Mimaki’s new product introductions continue to push the boundaries of what is possible and open up opportunities in new markets, and ‘vertical growth’ as it continues to support entry-level and industrial scale print production. Mimaki’s new ‘Print Different’ ethos underpins this approach. ‘Print Different’ not only encapsulates Mimaki’s legacy of breakthrough technologies but also highlights the company’s continuous commitment to driving creativity, differentiation and sustainability in the digital printing industry.

Rieter has signed a definitive agreement to acquire Barmag from OC Oerlikon for an upfront equity purchase price of CHF 713 million. The acquisition will create a globally leading player in natural and manmade fibers, headquartered in Winterthur, Switzerland, and is highly complementary to Rieter’s short-staple fiber business.

Barmag is a provider of filament spinning systems used for manufacturing manmade fibers, texturing machines, BCF1) systems, staple fiber spinning and nonwovens solutions and – as an engineering services provider – offers solutions along the textile value chain. In the financial year 2024, the company generated sales of CHF 734 million with around 2 600 employees.

Barmag comprises the established product brands Oerlikon Barmag, Oerlikon Neumag and Oerlikon Nonwoven. The main markets for the Barmag product portfolio are China, India, Türkiye and the United States of America. The innovative and technologically advanced products are developed in Remscheid and Neumünster (Germany) as well as Suzhou and Wuxi (China).

As fiber consumption is projected to rise, most of the growth is expected to come from manmade fibers. The increase of natural fibers such as cotton and linen is limited due to natural boundaries. Manmade fibers will help to meet expanding demand for clothing, technical and home textiles. The strategic acquisition of Barmag will transform Rieter into a leading supplier for converting natural and manmade fibers into yarn.

The transaction is fully in-line with Rieter’s strategy and follows previous acquisitions, where Rieter complemented its portfolio in short-staple fiber machinery and expanded its footprint in components and machinery for manmade fiber production. The combined platform allows to leverage the recovery of global filament and short staple fiber spinning markets and to reduce cyclicality due to diversification of end-markets. The acquisition will further enhance Rieter’s position in the important Asia-Pacific region and provide access to Barmag’s filament expertise, which will help to further scale Rieter’s own capabilities and improve digitization solutions and product sustainability.

Rieter’s largest shareholder, Peter Spuhler (c. 33% shareholding) is supportive of the transaction and committed to participating in the rights-issue pro-rata by exercising its subscription rights as well as investing additional capital through the non-pre-emptive capital raise. After the capital increase, PCS Holding AG is expected to retain a shareholding of c. 33%.

Additionally, Rieter’s second-largest shareholder, Martin Haefner (c. 10%), also supports the transaction and has committed to participating pro-rata in the rights-issue by exercising its subscription rights and investing additional capital through the non-pre-emptive capital raise.

CARBIOS, (Euronext Growth Paris:  ALCRB), a pioneer in the development and industrialization of biological technologies to reinvent the life cycle of plastic and textiles, announces to its shareholders and the financial community that its 2024 Universal Registration Document including the annual report, the management report and the report on corporate governance was filed with the French Financial Market Authority (Autorité des marchés financiers) on April 30, 2025 under the number D.25-0354.

Copies of the Universal Registration Document are available in French free of charge, pursuant to applicable law, and can be downloaded from the Company's website at www.carbios.com under the “Investors – Regulated information” section, as well as on www.amf-france.org. An English version will follow shortly.

On March 31, 2025, DEMGY Group took a decisive step in its international development strategy by acquiring the American company TOOL GAUGE, which specializes in the manufacture of plastic components for the interior of aircraft cabins. This acquisition will enable DEMGY to consolidate their position as one of the world leaders in high value-added plastics processing for civil and military aeronautics.

With this operation, DEMGY is extending its footprint on the North American market, a strategic territory for the aerospace sector. The American company, now renamed DEMGY Pacific, is thus joining a group already present in France, Germany, Romania and the United States, bringing the total number of the group's industrial sites to 10.

Recognized expertise for the benefit of American aerospace
Based in Tacoma, Washington State, TOOL GAUGE has nearly 60 years of experience in the processing of high-performance polymers and the machining of precision parts. Recognized for its operational excellence, it has been awarded the Silver Performance Excellence Award by Boeing for 9 consecutive years.

The company has two complementary production units: one dedicated to plastic injection, particularly for interior fittings in aircraft cabins, and the other specializing in the machining of metal and plastic parts. This technical expertise considerably strengthens DEMGY's offering to major clients in the aerospace sector.

Airbus, Boeing: DEMGY stands out as a key partner
This strategic acquisition enables DEMGY to become a tier 1 supplier for Boeing and Airbus, as well as a tier 2 supplier for all their equipment manufacturers in Europe and North America. This positioning considerably strengthens the group's visibility and attractiveness on the global aerospace market.

"By strengthening its leadership in high value-added plastics processing for the aerospace and defense industries, the DEMGY Group has become one of the world's leading, if not the leading, supplier of plastic parts for cabin interiors directly to Airbus and Boeing, as well as to all American and European aircraft equipment manufacturers," says Pierre-Jean LEDUC, Chairman and CEO of DEMGY Group. "This enables us to deploy our high and extreme performance plastics solutions on a much larger scale".

Integration driven by DEMGY Group's cross-functional synergies
DEMGY Pacific will be managed by Mike Walter, also President of DEMGY Chicago, and Eric Wilmoth, Vice-President of Operations. Both will be tasked with implementing industrial and commercial synergies with all the entities of the group, particularly in terms of injection, assembly and decoration.

This integration will promote the development of global solutions to meet the growing demands of the aerospace industry in terms of lightness, performance and durability.

Target of 200 million euros: managed growth
With its 10 industrial sites and 950 employees, DEMGY forecasts sales of over 130 million euros by 2025. Our group's ambition is to reach 200 million euros by 2030, capitalizing on its unique know-how, capacity for innovation and proximity to major customers.

Materials lightening at the heart of decarbonization
For several years, DEMGY has been committed to reducing the carbon footprint of industries, by designing polymer materials that are lighter than metal, durable and recyclable.Thanks to our circular Multiplasturgy® offer, we integrate eco-design from the product development phase.

As the Indian textile and apparel sector embraces digitisation, sustainability, smarter production and responsible manufacturing, Gartex Texprocess India emerges as a critical node in this narrative bringing together the textile and garment machinery manufacturers, denim mill owners, digital textile printing technology solution providers, as well as manufacturers of apparel fabrics, textile and textile processing machinery and more, who are set to unfold innovations. With 125+ participating companies, representing 300+ brands and growing participation from international countries, this edition will offer a panoramic view of the sectors next chapter.

India’s textile industry often referred to as the lifeblood of nations manufacturing economy, is on the cusp of a technology-led transformation. Leading this evolution is Gartex Texprocess India – Mumbai organised by Messe Frankfurt Trade Fairs India Pvt Ltd and MEX Exhibitions Pvt Ltd. The expo is a definitive sourcing and innovation platform growing with global participation and solutions for the future.

What sets this edition apart is its focused attention on technology integration, automation and responsible manufacturing – themes that are redefining how India produces, sources and innovates on the global textile map through its product showcase as well as curated knowledge sessions.

A global showcase:
Making headlines this year is the strong international participation especially from China, Italy, Japan, Korea, Singapore and a dedicated pavilion for Taiwan, along with the leading Indian companies on board. Displaying a wide range of products for the garment and textile manufacturing industry. A few international names include: EPSON, Kornit and MACPI International among others. Some will participate directly and some through their partners and distributors. This global representation is matched with a stellar Indian line-up featuring names such as Balaji Sewing Machines, DCC, EH Turel, Mexum, Pantone and Sky Enterprises amongst others.

Denim Takes Centre Stage:
With the backing of Denim Manufacturers Association, the Denim Show at Gartex Texprocess India is expected to bring together all the major denim manufacturers and mill owners from India under one roof. As Indian denim exports steadily rise and demand for eco-conscious denim production grows, the show provides a much-needed window into how this resilient segment is re-inventing itself with sustainability and style at its core.

Trims & Accessories:
Beyond denim, this edition places a sharp focus on innovative fabric solutions, trims, digital screen printing and accessories – with dedicated zones for the Fabrics and Trims shows and Screen-Print India - Textile.

With 25+ new entrants and expanding categories, the Mumbai edition will be a hotspot for denim designers, boutique owners, apparel brands and labels, garment manufacturers, dyeing and finishing companies, distributors and agents of textile and garment machinery and accessories, merchandisers and sourcing heads scouting for the latest in material and design and more.

As India marches towards becoming a global textile powerhouse, Gartex Texprocess India – Mumbai 2025 will serve as the ultimate confluence of technology, talent and trade, weaving together a stronger future for the Indian textile industry.

Gartex Texprocess India is a leading exhibition in the textile manufacturing technology with collocated show: The Denim Show’ and dedicated featured zones of ‘Fabrics and Trims Show’ and ‘Screen Print India – Textile’ making this a one-stop destination for the textile manufacturing.

The expo is jointly organised by MEX Exhibitions Pvt Ltd and Messe Frankfurt Trade Fair India Pvt Ltd. Gartex Texprocess India Mumbai and is scheduled from 22 – 24 May 2025 at Jio World Convention Centre, Mumbai, Maharashtra.

adidas announced its latest edition of Move For The Planet - the annual initiative that focuses on making sports facilities more resilient against extreme weather conditions, across the globe. By inspiring everyday athletes to track movement, funds are raised to help deliver sustainability education and help improve the places that sport is played.

For every ten minutes of relevant activity logged in the adidas Running app – or, for the first time, Strava - between 12th-25th May, adidas will donate €1 - up to a total of €1.5 million - to several projects across the globe.  Participants can choose from over 100 trackable sports and movements including running, swimming and wheelchair rugby – and add to the 400,000,000 minutes of movement already logged since the initiative began in 2023.

Working with its partners – Common Goal and UN Climate Change - adidas will donate the funds to implement and upgrade infrastructure for communities impacted by extreme weather. This includes weather-resistant facilities – such as water harvesting and purification systems introduced into projects such as United Through Sport in South Africa and waste management processes like the system implemented through Enabling Leadership in India.

The funds raised also provide accessibility to an education platform for global NGOs and organizations, that enable education on more sustainable actions – using the power of sport to help ensure its future in communities. This year, it will directly impact projects such as Girls United in Mexico, El Rio in Colombia, Red Deporte in Spain and United Through Sport in South Africa.

Since its inception, Move For The Planet has helped introduce sustainability education programs to over 8,000 individuals and over 23,000 people have had access to improved sporting facilities across all participating projects.

Ashley Czarnowski, Senior Director, Global Purpose Marketing at adidas said: “We’re delighted to welcome back Move For The Planet for a third year. It’s an extremely important initiative that helps to support sporting communities facing the effects of extreme weather.  With the continued expansion of sports and projects included in Move For The Planet, we can’t wait to see the movement and impact grow even further. This year we are calling for the adidas community to be catalysts for action; motivating the people in their lives to join in and get moving.”

To help inspire more movement, a new roster of global adidas athletes join Move For The Planet for the first time. This will include FIFA World Cup winner Alexis Mac Alister, Downhill Mountain Bike World Cup Champion Valentina Höll, Commonwealth Games gold medallist Ferdinand Omanyala and renowned health and fitness coach Massy Arias. Featuring in a series of short films inspired by their own connection to foundational sporting spaces, each athlete outlines the communities that rely on them, and the role these facilities play for the next generation of athletes.

Rute Caldeira, Head of Impact at Common Goal said: “Move for the Planet exemplifies the power of collaboration in driving the urgent action needed to make sports facilities more resilient. This partnership is invaluable to us, as it combines innovation with impact. Leveraging sports-for-good organizations, deeply rooted in the fabric of their communities, is a game-changing strategy in our approach to this goal. Over the past two years, Move for the Planet has delivered transformative results, enabling real and lasting improvements in some of the most resource-scarce regions of the world. We’re thrilled to continue this vital work into a third year, building a brighter future for the communities who need it most.”

Lindita Xhaferi-Salihu, Sports for Climate Action Lead at UN Climate Change, said: “This partnership aims to strengthen sustainability knowledge and action within the sports community, as it brings together diverse expertise and best practice case studies to sport organizations and sport NGOs. By sharing perspectives, needs and collaborating on solutions, we can drive positive change, strengthen communities, and create lasting impact through sport.”

Denim is timeless. From casual Fridays to nights out, from factory floors to fashion runways - jeans have become an essential part of modern life. But there's one thing even the most loyal denim lovers can't deny: on warm days, they can make you sweat. Outlast Technologies GmbH is changing that - by making denim that helps you sweat less and feel more comfortable throughout the day.

After intensive research and development, Outlast introduces its temperature regulation technology into denim fabrics - without compromising the rugged authenticity and durability denim is known for. The result is a smarter, more comfortable denim that adapts to the body's temperature, no matter the season or activity.

“Jeans are the undisputed icon of modern fashion - they work for every occasion,” says Volker Schuster, director of R&D at Outlast Technologies GmbH. “But when the temperature rises, they can become uncomfortable. That’s exactly the problem we wanted to solve. Our solution is a denim fabric that works with your body, not against it.”

The innovation lies in embedding natural wax directly into the fibers before the denim is woven - creating intelligent fabrics that interact with your body. When it’s warm, these fibers absorb excess body heat and store it, helping to reduce sweating and keep you feeling comfortably balanced. As temperatures cool or your activity level decreases, the stored warmth is gradually released - helping to prevent chills. The result? Jeans that intuitively adapt to your body’s needs, so you stay comfortable, whatever the day brings.

Achieving this level of functionality, however, was no easy task. The challenge was to ensure that the temperature-regulating effect could withstand the intense wash and finish treatments typical in denim production - all while preserving the look, feel, and durability expected of high-quality jeans.

To meet these demands, Outlast found the perfect partner in AGI, the renowned denim producer from Pakistan. With its deep expertise in denim manufacturing, AGI played a key role in refining the integration of temperature regulation technology - resulting in denim products that are highly attractive to both brands and end consumers alike.

Equally appealing to end users is the lasting performance of the innovation: the natural wax is embedded inside the fiber itself. This means the temperature-regulating function does not wash out or diminish over time. Unlike surface treatments, the technology remains effective throughout the entire life cycle of the garment.

With this development, Outlast reaffirms its position as a pioneer in temperature regulation textiles - bringing comfort, performance, and innovation to one of the world’s most beloved fabrics.