From the Sector

The DITF is leading the joint project "DACCUS-Pre*". The basic idea of the project is to develop a new building material that stores carbon in the long term and removes more CO₂ from the atmosphere than is emitted during its production.       

In collaboration with the company TechnoCarbon Technologies, the project is now well advanced - a first demonstrator in the form of a house wall element has been realized. It consists of three materials: Natural stone, carbon fibers and biochar. Each component contributes in a different way to the negative CO₂ balance of the material:

Two slabs of natural stone form the exposed walls of the wall element. The mechanical processing of the material, i.e. sawing in stone cutting machines, produces significant quantities of stone dust. This is very reactive due to its large specific surface area. Silicate weathering of the rock dust permanently binds a large amount of CO₂ from the atmosphere.

Carbon fibers in the form of technical fabrics reinforce the side walls of the wall elements. They absorb tensile forces and are intended to stabilize the building material in the same way as reinforcing steel in concrete. The carbon fibers used are bio-based, produced from biomass. Lignin-based carbon fibers, which have long been technically optimized at DITF Denkendorf, are particularly suitable for this application: They are inexpensive due to low raw material costs and have a high carbon yield. In addition, unlike reinforcing steel, they are not susceptible to oxidation and therefore last much longer. Although carbon fibers are more energy-intensive to produce than steel, as used in reinforced concrete, only a small amount is needed for use in building materials. As a result, the energy and CO₂ balance is much better than for reinforced concrete. By using solar heat and biomass to produce the carbon fibers and the weathering of the stone dust, the CO₂ balance of the new building material is actually negative, making it possible to construct CO₂-negative buildings.

The third component of the new building material is biochar. This is used as a filler between the two rock slabs. The char acts as an effective insulating material. It is also a permanent source of CO₂ storage, which plays a significant role in the CO₂ balance of the entire wall element.

From a technical point of view, the already realized demonstrator, a wall element for structural engineering, is well developed. The natural stone used is a gabbro from India, which has a high-quality appearance and is suitable for high loads. This has been proven in load tests.  Bio-based carbon fibers serve as the top layer of the stone slabs. The biochar from Convoris GmbH is characterized by particularly good thermal insulation values.

The CO₂ balance of a house wall made of the new material has been calculated and compared with that of conventional reinforced concrete. This results in a difference in the CO₂ balance of 157 CO₂ equivalents per square meter of house wall. A significant saving!

* (Methods for removing atmospheric carbon dioxide (Carbon Dioxide Removal) by Direct Air Carbon Capture, Utilization and Sustainable Storage after Use (DACCUS).

STFI will be presenting high-end textile products and solutions at Techtextil 2024. The highlights from current research results and innovations provide an insight into the digitalisation of textile production, show applications for 3D printing and smart technical textiles and provide examples of particularly sustainably designed products as well as innovative approaches for protective and medical textiles.

The central highlight of STFI's presence at Techtextil is a robot system that demonstrates the automated processing of a bobbin frame on a small scale. The pick-and-place application demonstrates camera-supported gripping of the bobbins. The robot is part of the STFI's “Textile Factory of the Future” which demonstrates automation solutions for the textile industry in a laboratory environment.

From the field of sustainable products and solutions, a sleeping bag with bio-based and therefore vegan filling material and a natural fibre-based composite element for furniture construction, in which LEDs and capacitive proximity sensors for contactless function control have been applied using embroidery technology, will be on show. Printed heating conductor structures demonstrate current research work for the e-mobility of the future, as the individually controllable seat and interior heating should ultimately reduce weight and save energy compared to conventional heating systems.

While a protective suit for special task forces protects against the dangers of a Molotov cocktail attack, a shin guard and a knee brace with patellar ring illustrate the process combination of 3D printing and UV LED cross-linking. Other highlights from lightweight textile construction include the rib of a vertical rudder of an Airbus A320 and a green snowboard made from recycled carbon fibres.

Groz-Beckert offers interested machine builders various cooperation opportunities to jointly develop new products or improve existing ones. In collaboration with Vanguard Pailung, a manufacturer of ultra-high-speed knitting machines for body-size products, Groz-Beckert has developed an innovative slider needle for a new generation of machines. Groz-Beckert's Technology and Development Center (TEZ) provides the appropriate framework for so-called co-development projects.

In June 2022, Vanguard Pailung approached Groz-Beckert with a cooperation request. Together with Groz-Beckert, the company wanted to develop a new needle solution for an innovative ultra-high-speed machine. Together with an innovative slide needle, the new machine was to exceed the speed and productivity of known knitting systems of large circular knitting machines.

Machine and needle development ran in parallel and were closely coordinated. The first field tests took place in the Vanguard Pailung laboratory in Monroe/NC, USA in February 2023. The successful development was presented to a wide audience for the first time at ITMA 2023 in June.

Unlike latch needles, slide needles do not form the stitch via a needle latch, but via a slide that is controlled by its own channel. The advantage of this is that the needle can withstand high speeds, as there is no latch impact, which in turn increases productivity.

The use of the new slide needle in ultra-high-speed machines ensures a particularly high level of process reliability. With the new needle variant, the closer is guided safely and precisely in the groove in the needle shank. At the same time, the base of the needle shank is closed, which ensures maximum stability. The slider needle reliably prevents the so-called latch impact and thus makes a decisive contribution to process reliability. Its use ensures a uniform and speed-independent loop structure, even at maximum speeds.

• Solvay’s FY 2023 financial statements reflect the Partial Demerger completed on December 9, 2023, with the Specialty businesses transferred to Syensqo classified as discontinued operations for 2023.
• New Solvay leadership team committed to drive the transformation of the company.
• Net sales for the full year 2023 at €4,880 million were down -12.6% organically versus 2022, driven primarily by volume declines. In Q4, net sales decreased organically by -18.9% from both lower volumes and prices.
• Underlying EBITDA of €1,246 million for the full year 2023 was stable (+0.2%) on an organic basis compared to a record 2022, with positive Net Pricing and lower fixed costs offsetting the drop in volumes. EBITDA in the fourth quarter was down -24.5% organically vs Q4 2022, fully driven by lower volumes, with variable costs reduction offsetting price erosion, while fixed costs decreased slightly.
• Underlying net profit from continuing operations was €588 million in 2023 compared to €740 million in 2022.
• Free Cash Flow of €561 million in 2023 (+17.3% vs. €479 million in 2022) resulting in a record FCF conversion ratio of 45.4%, thanks to the strong EBITDA performance and to the positive impact from working capital variation.
• ROCE was 20.4% in 2023, -2.5pp compared to 2022 as a result of lower profit.
• Solid balance sheet at the end of December 2023, in line with the target capital structure announced in November 2023, with an underlying net debt of €1.5 billion, which translates into a leverage ratio of 1.2x.
• Total proposed gross dividend of €2.43 per share, subject to shareholders’ approval during the next Ordinary General Meeting of May 28, 2024.
• Solvay continues to reduce its GHG emissions (-19% vs 2021, scope 1 and 2).
• 2024 Outlook: Organic growth of the underlying EBITDA of -10% to -20% compared to restated 2023; Free cash flow of minimum €260 million

2024 outlook
Across its product portfolio, Solvay expects current demand levels to continue over the next few months and, as such, expects H1 2024 volumes to be broadly in line with H2 2023. At this point, there is little visibility on the second half of the year, however there are signs that the trend in the second half could improve. Solvay expects Soda Ash prices over FY 2024 to be lower than FY 2023, consistent with the current market environment, which will affect the business margin in 2024. Pricing trends across Solvay’s other businesses are forecasted to be more resilient year on year.

Lower energy and raw materials prices should offset some of the negative pressure on the topline. More importantly, Solvay has started to implement cost savings initiatives that will start to deliver results in 2024.

For full year 2024, Solvay expects an organic growth of the underlying EBITDA by -10% to -20% versus a high comparison base in 2023, especially in H1. This translates into a range of €925 million to €1,040 million at a 1.10 EUR/USD exchange rate.

The organic growth of the underlying EBITDA is calculated from a 2023 restated figure of €1,154 million (vs a reported figure of €1,246 million).

Free cash flow to Solvay shareholders from continuing operations is expected to be greater than €260 million, in line with the cash usage prioritization presented during the Capital Market Day in November 2023. It is supported by Solvay’s ability to manage its capex and working capital to ensure the financing of its businesses and the payment of dividends while keeping the strength of its balance sheet intact.

Solvay remains committed to implement its strategic roadmap and reconfirms its 2028 targets as communicated at the Capital Markets Day of November 2023.

• adidas and Yohji Yamamoto return to present their second Y-3 Atelier collection.

For its second collection, Y-3 Atelier introduces a suite of tailored pieces which blend adidas’ performance heritage with Yohji Yamamoto’s design vision. The collection takes original Yohji Yamamoto and Yohji Yamamoto POUR HOMME designs that are from the runway show and recreates them in fully seam sealed waterproof 3-layer GORE-TEX® material constructions, while maintaining the signature silhouette of the original designs. Featuring extended seams and flap pockets, the selection of monochromatic black vests, coats, parkas, blousons, jackets, and blazers comes replete with reflective logos.

Accompanying the launch of the collection is a series of still images captured by photographer Thue Nørgaard which convey the dynamism of each piece.

Together with Cotton made in Africa (CmiA) and the cotton company MMP Agro, the GoodTextiles Foundation is realising a project to improve the drinking water supply in Uganda, Africa. Bio-sand-waterfilters are being installed to gently purify the water from existing sources. In addition, the partners are training the community's farmers and craftsmen in how to operate the water filters. They then learn how to build new water filters.

In 2016, the textile company Dibella established the GoodTextiles Foundation with the aim of making textile value chains more sustainable. It raises donations and implements its own funding projects to benefit people at all stages of the textile industry.

As part of a joint project between the GoodTextiles Foundation, the Aid by Trade Foundation (AbTF) (owner of the CmiA standard) and MMP Agro, farmers who grow CmiA cotton in the districts of Abim, Kaplebyong, Dokolo and Kaberamaido in north-east Uganda are now receiving a total of around 1,000 bio-sand-waterfilters. Around 1,000 CmiA farmers, mainly women and the members of their households (an estimated 10,000 community members) benefit from this.

Members of TMAS – the Swedish textile machinery association – will display technologies in alignment with the theme of digitalisation at the forthcoming Techtextil and Texprocess 2024 exhibitions, taking place in Frankfurt from April 23-26th.

Automatic handling
The fully automated and digitised handling solutions for finished garments, home textiles and furniture of Eton Systems, for example, will be demonstrated at Texprocess.

Designed to increase value-added time in production by eliminating manual transportation and minimising handling, the individually addressable product carriers are fully managed and controlled by the latest ETONingenious™ software. This web based real-time data collection and information system continuously accumulates, processes and makes all production information instantly available to supervisors, quality control personnel and management.

Bespoke seams
Svegea will demonstrate its EC 300-XS colarette technology, which is used by garment manufacturers around the world for the production of tubular apparel components such as cuff and neck tapes and other seam reinforcements.

The EC 300-XS collarette cutter on show in Frankfurt is equipped with the latest E-Drive II system providing the operator with a very user-friendly touchscreen, providing full control of the cutting process. An accompanying FA 350 fully automatic roll slitting machine will also be demonstrated.

Digital finishing
At Techtextil meanwhile, Baldwin Technology Co. will provide full details of how its highly digitised TexCoat G4 non-contact spray technology for textile finishing and remoistening not only reduces water, chemicals and energy consumption, but also provides the flexibility to adapt to customer requirements in terms of single and double-sided finishing applications.

TexCoat G4 can reduce water consumption and chemical usage by as much as 50% compared to traditional padding application processes.

Yarn tension
Celebrating its 60th anniversary this year, Eltex will display the latest Eltex EyETM system for the continuous monitoring of yarn tension on warp beams.

The Eltex EyETM eliminates problems when warping, and also in subsequent weaving or tufting processes, monitoring the yarn tension on all positions in real-time and enabling a minimum and maximum allowable tension value it be set. If any yarn’s tension falls outside these values the operator can be warned or the machine stopped.

The Eltex ACT and ACT-R units meanwhile go beyond yarn tension monitoring to actually control yarn tension. This extends the application range greatly. The plug and play system automatically compensates for any differences in yarn tension that arise, for example from irregularities in yarn packages.

Accumulated know-how
Vandewiele Sweden AB benefits from all of the synergies and accumulated know-how of Vandewiele Group, supplying weft yarn feeding and tension control units for weaving looms to the majority of weaving machine manufacturers. It also retrofits its latest technologies to working mills to enable instant benefits in terms of productivity and control.

The company will present its latest X4 yarn feeders with integrated accessory displays (TED) as a new standard, as well as launching its own e-commerce platform – iroonline.com.

The TED function enables weft tension settings to be transferred from one machine to another, enabling a fast start-up the next time the same article is woven. The position of the S-Flex Tensioner is constantly monitored by an internal sensor – even if adjustment is made during power off.

X4 feeders are also available with integrated active tension control (ATC-W) as an option. With the ATC-W active tension control, the required tension is easily set and monitored on the integrated display. Once set, the system constantly regulates itself, ensuring consistent yarn tension during the weaving process which is constantly and accurately measured by the ATC sensor unit, sending a signal to the ATC operator unit resulting in consistently stable yarn tension at the required level.

A new promotional initiative aims to boost trade relations between Italy and India in the textile sector. 11 Italian textile machinery manufacturers will be taking part in the forthcoming technological symposia scheduled in New Delhi and Mumbai from 9 to 12 April. The two events, organized by the Italian Trade Agency and supported by the Ministry of Foreign Affairs and International Cooperation, will allow Italian companies to showcase their technologies to a selected audience of Indian textile entrepreneurs.

The textile sector is of great significance in the Indian economy, contributing more than 2% of the GDP and allowing the Country to be among the largest exporter of textile and apparel items. Moreover India represents the third largest foreign market for the Italian textile machinery industry.

In 2022 India imported Italian textile machinery for a total value of about 200 million euro. Referring to the first 9 months of 2023, the value shows a slight decrease compared to the value for the same period of the previous year, but the forecast for the current year remains positive.

Italian companies participating in the symposia, all of which are ACIMIT members, are: Autefa, Cubotex, Danitech, Lafer, Mcs, Monti-Mac, Reggiani Macchine, Salvadè, Savio, Sicam, Testa.

Freudenberg Performance Materials (Freudenberg) is showcasing solutions for the automotive, building, apparel, filtration and packaging industries at this year’s Techtextil in Frankfurt am Main from April 23 – 26.

Sustainable nonwoven for car seats
One innovation highlight at Techtextil is a novel Polyester nonwoven material for car seat padding. Also available as a nonwoven composite with PU foam, it is not only easier for car seat manufacturers to handle during the mounting process, but also ensures better dimensional stability as well as providing soft and flexible padding. It has a minimum 25 percent recycled content, for example, by reusing nonwoven clippings and waste, and is fully recyclable. Full supply chain transparency enables customers to trace and verify the content of the nonwoven and thus ensures a responsible production process. The Freudenberg experts will also be presenting several other nonwoven solutions made of up to 80 percent recycled materials that can be used in car seat manufacturing.

Biocarrier for green roofs
Freudenberg is showcasing a sustainable carrier material for green roofs on urban buildings at the trade fair. The carrier is made from polylactide, i.e. from renewable resources. When filled with soil, it provides a strong foothold to root systems, enabling the growth of lightweight sedum blankets that can be rolled out to provide instant green roofs. These roofs not only help counter urban heat, they also improve stormwater management and regulate indoor temperatures.

From textile waste to padding
The company extended its circular thermal wadding product range with the release of comfortemp® HO 80xR circular, a wadding made from 70 percent recycled polyamide from discarded fishing nets, carpet flooring and industrial plastic. Because polyamide 6, also known as nylon, retains its performance characteristics after multiple recycling processes, the fibers can be used again and again to manufacture performance sporting apparel, leisurewear and luxury garments.

Packaging solutions with various sustainability benefits
Freudenberg is also showcasing products for sustainable packaging and filtration solutions. The long-lasting Evolon® technical packaging series is a substitute for disposable packaging used in the transport of sensitive industrial items such as automotive parts. The material is made from up to 85 percent recycled PET. A further highlight at Techtextil are Freudenberg’s fully bio-based solutions for manufacturing dessicant bags. The binder-free material based on bio-fibers is also industrially compostable.
In addition, the experts will be giving trade fair visitors an insight into Freudenberg’s filtration portfolio.

Representatives from all 43 European partners of RegioGreenTex met for the Annual Consortium Meeting, hosted by CITEVE – the Portuguese Centre for textile innovation.

Co-funded by the European Union I3 Instrument Programme, RegioGreenTex is a €13 million project to promote investments in textile circularity. Research centres, regional clusters, regional development agencies and 26 SMEs collaborate to realise unique pilot projects to transform the textile industry business model from linear to circular.
 
The annual consortium meeting is a pivotal point to assess the project’s progress and impact. Presentations and workshops have been an essential part of the meeting, along with  networking opportunities where partners created synergies and discussed common challenges. Furthermore, all SME partners showcased their results through an exhibition with samples of garments, yarns, fabrics and products: the outcome of the project’s innovation so far. New collaborations and partners are expected to flourish as another outcome and the meeting.

EURATEX, as project coordinator, ensures the successful implementation of this ambitious initiative. Dirk Vantyghem, EURATEX Director General, commented: “RegioGreenTex is an essential piece of our wider plan to implement the EU Sustainable Textile Strategy. Offering investment support to our SMEs is critical to make this green transition a success.”