From the Sector

With the goal of making recycling of lightweight, high-volume fiber and flake recyclate much more economical and, in some cases even possible, Coperion has developed a new version of its ZS-B side feeder. Using the innovative ZS-B MEGAfeed, plastic recyclate with a bulk density under 200 kg/m³, long considered intake-limited and thus not worth recycling, can be reliably fed in large quantities into Coperion’s ZSK twin screw extruder and be concurrently recycled and compounded.

The ZS-B side feeder’s novel design makes it possible to feed very high rates of fiber and flakes, such as PA, PE, PET, and PP. As a result, the ZSK twin screw extruder’s high capacity can be fully exploited when the ZS-B MEGAfeed is used. Very high throughputs in both mechanical and chemical recycling of post-industrial and post-consumer waste are achieved.

Increased Throughput in Numbers
With a ZSK 58 Mc18 twin screw extruder, the throughput increase and thus the potential of the new ZS-B MEGAfeed becomes very clear. When recycling PA fibers with a bulk density of ~40-50 kg/m3, throughputs of 70 kg/h were previously achieved using conventional equipment. When the PA fibers were fed into the ZSK extruder using the ZS-B MEGAfeed, throughputs increased about fourteenfold to 1,000 kg/h. Similar results were achieved recycling carbon fibers with a bulk density of ~50-70 kg/m3; in this case, throughputs increased from 50 kg/h to 2,500 kg/h using the ZS-B MEGAfeed. When recycling PCR (Post-Consumer Recycled) flakes, throughputs increased from 50 kg/h to 700 kg/h, and from 80 kg/h to 1,300 kg/h with multilayer film flakes.

Key to Economical Recycling of A Wide Variety of Plastics
Plastics previously considered not recyclable are becoming a valuable raw material using the new Coperion ZS-B MEGAfeed. For example, PCR flakes or recyclate from carbon fiber-reinforced plastics can now be fed into the ZSK extruder at high feed rates and recycled economically.

In the case of mechanical upcycling, upstream processes necessary for compounding, such as compacting, melting and agglomeration, are completely eliminated using the ZS-B MEGAfeed technology. In this recycling process, flakes and fibers can be fed directly into the ZSK extruder, where they are melted, compounded, devolatilized, and filtered in a single step. In so doing, both investment costs and energy consumption drop. The production process becomes significantly more efficient. Moreover, the thermal product stress is reduced and recyclate quality increases.

Even when recycling PET, the feed rate is no longer a limiting factor. With the ZS-B MEGAfeed, PET flakes and fibers can be fed into the ZSK twin screw extruder in large quantities with no pre-drying or crystallizing, where they can be processed with the highest degree of profitability.

The ZS-B MEGAfeed can also feed large quantities of post-consumer waste, adding appreciable value to the chemical recycling process with the ZSKs. ZSK throughput rates are very high with the ZS-B MEGAfeed. Preheating of the recyclate via mechanical energy input of the twin screws thus becomes even more economical for further processing in the reactor.

Existing Coperion extruders can be retrofitted with ZS-B MEGAfeed technology to greatly expand their spectrum of applications and increase their throughput rates.

The European Pultrusion Technology Association (EPTA) has published a report from its latest conference, which focuses on advances in sustainability and recycling.

More than 130 professionals from the global pultrusion community gathered at the 16th World Pultrusion Conference in Paris on 5-6 May 2022. Organised by EPTA in collaboration with the American Composites Manufacturers Association (ACMA), the event featured 25 international speakers sharing insight on market trends, developments in materials, processing and simulation technologies, and innovative pultruded applications in key markets such as building and infrastructure, transportation and wind energy.

‘Bio-pultrusion’:  
Composites based on natural fibres offer a number of benefits, including low density and high specific strength, vibration damping, and heat insulation. The German Institutes for Textile and Fiber Research Denkendorf (DITF) are developing pultrusion processes using bio-based resins and natural fibres. Projects include the BioMat Pavilion at the University of Stuttgart, a lightweight structure which combines ‘bamboo-like’ natural fibre-based pultruded profiles with a tensile membrane.

Applications for recycled carbon fibre (rCF):
The use of rCF in composite components has the potential to reduce their cost and carbon footprint. However, it is currently used to a limited extent since manufacturers are uncertain about the technical performance of available rCF products, how to process them, and the actual benefits achievable. Fraunhofer IGCV is partnering with the Institute for Textile Technology (ITA) in the MAI ÖkoCaP project to investigate the technical, ecological and economic benefits of using rCF in different industrial applications. The results will be made available in a web-based app.

Circularity and recycling:
The European Composites Industry Association (EuCIA) is drafting a circularity roadmap for the composites industry. It has collaborated with the European Cement Association (CEMBUREAU) on a position paper for the EU Commission’s Joint Research Centre (JRC) which outlines the benefits of co-processing end-of-life composites in cement manufacturing, a recycling solution that is compliant with the EU’s Waste Framework Directive and in commercial operation in Germany. Initial studies have indicated that co-processing with composites has the potential to reduce the global warming impact of cement manufacture by up to 16%. Technologies to allow recovery of fibre and/or resin from composites are in development but a better understanding of the life cycle assessment (LCA) impact of these processes is essential. EuCIA’s ‘circularity waterfall,’ a proposed priority system for composites circularity, highlights the continued need for co-processing.

Sustainability along the value chain:
Sustainability is essential for the long-term viability of businesses. Resin manufacturer AOC’s actions to improve sustainability include programmes to reduce energy, waste and greenhouse gas emissions from operations, the development of ‘greener’ and low VOC emission resins, ensuring compliance with chemicals legislation such as REACH, and involvement in EuCIA’s waste management initiatives. Its sustainable resins portfolio includes styrene-free and low-styrene formulations and products manufactured using bio-based raw materials and recycled PET.

Indorama Ventures, VALORPLAST, Klöckner Pentaplast (kp) and CITEO collaboration delivers a commercial recycling solution for monolayer PET trays

Thai-based Indorama Ventures Public Company Limited (IVL) with its facility Wellman France Recycling in Verdun, has been working on the PET trays recycling for 6 years and through an ongoing project with VALORPLAST and supported by CITEO.

The project has the objective to develop and validate recycling for monolayer and multilayer PET trays. VALORPLAST has collected significant quantities of post-consumer PET trays and several industrial runs have been conducted by Wellman. The produced flakes are being tested by several actors to develop high quality applications. Those tests have led by IVL to develop a commercially feasible recycling solution for monolayer PET trays with the collaboration of Klöckner Pentaplast.
The new technology is processing monolayer PET trays used for food packaging (meat, produce and cheese) into a high-quality product, suitable for new tray production.

This new recycling innovation will see over 50 million post-consumer PET trays diverted away from landfill or incineration.

Testing has now moved into commercial production. 500 tonnes of PET trays are now being processed monthly and transformed into a high-quality tray flake, which can be used to produce new trays. The purity of the flakes is comparable with high-quality bottle flake. A further scale up is foreseen, and the company plans to process 10KT of tray flake in 2022.

International textile producers meet again in Istanbul, Turkey, from June 14 – 18, 2022 on the occasion of the ITM + Hightex Exhibition. In Hall 9 (Hightex) the exhibitors will present the complete industry value chain from nonwovens raw materials, production machines and accessories to the endproduct. The related industries covered include hygiene, filtration, fabrics and apparel, medical, automotive, wipes, home furnishings and upholstery. DiloGroup offers tailor-made production systems from one supplier and will inform about its portfolio and the latest equipment developments from fibre opening to the finished felt.

DiloGroup will inform about complete lines as well as high speed needlelooms for spunbonds. A new, simplified elliptical needle beam drive makes Hyperpunch technology also attractive for standard application. Hyperpunch HαV allows a more uniform stitch distribution in the preneedling process especially in combination with the new needle pattern 6000X. In a complete needling line this felt homogenization process can be improved further. The new needle pattern 8000X is a milestone in the needle pattern development process and results in endproduct surfaces with low markings over a wide range of advances/stroke.

Another strong pillar of the sales program over decades has been fibre preparation and high speed webforming equipment for other nonwoven technologies. The further development of the high-speed layering principle “Hyperlayer” made progress for better CD strength through a combination of inline cards and crossline card with crosslapper. Particularly, carding machines in a working width above 3.5 m up to 5.1 m have been supplied by DiloSpinnbau as complete high speed carding systems, comprising two or even three cards in a line to directly feed the hydroentangling units of various suppliers. Together with DiloTemafa not only have high throughput rates been achieved in the fibre preparation section of the line but also dedusting filtering and air-conditioning systems have been successfully engineered and integrated.

Together with Sicam, Dilo has combined know-how for hydroentangling technology and therefore can provide complete lines as general contractor including equipment for cutting, winding and packaging.

Another interesting machine is the 3D-Lofter, first presented during ITMA 2019 in Barcelona, which offers a wider range of nonwovens applications by exploring the third dimension. A series of single web forming units which work according to the aerodynamic web forming principle deliver defined fibre masses in varied patterns on a base needlefelt. A stress oriented production of technical formed parts resulting in fibre savings or patterned DI-LOUR or DI-LOOP felts with or without repeat are two examples for this technology which explores new application areas for needlefelts.
The 3D-Lofter technology may also be used “inverted” as “IsoFeed” for filling up bad spots in web mats and thus achieves a better homogeneity of spunlace or airlay products.

The DiloLine 4.0 concept offer I4.0 modules which not only support the user but also facilitate quality control and maintenance by a maximum data transparency in production and control of operation. The Dilo solutions “Smart Start” for a fully automatic start of the production line or “DI-LOWATT” for energy savings are accompanied by Siemens solutions which can be selected via App or Data Cloud “MindSphere”.

• Sustainable infrastructure solutions, road safety and health protection

At this year’s Techtextil, Oerlikon Polymer Processing Solutions will be presenting the trade audience with new applications, special processes and sustainable solutions focusing on the production of industrial textiles. Among other things, the company will be showcasing new technology for charging nonwovens that sets new standards with regards to quality and efficiency. Between June 21 and 24, the discussions will be concentrating on airbags, seat belts, tire cord, geotextiles, filter nonwovens and their diverse applications.

More polyester for airbags
Airbags have become an integral part of our everyday automotive lives. The yarns used in them are made predominantly from polyamide. As a result of increasingly diverse airbag applications and also the increasing size of the systems used, polyester is today used as well, depending on the application requirements and cost-benefit considerations. Against this background, the Oerlikon Barmag technologies make an invaluable contribution. In addition to high productivity and low energy consumption, they particularly excel in terms of their stable production processes. Furthermore, they comply with every high quality standard for airbags, which – as in the case of virtually all other textile products used in vehicle construction – must provide the highest level of safety for vehicle occupants. And all this without any loss of function in any climate and anywhere in the world for the lifetime of the vehicle.

Buckle up!
Seat belts play a decisive role in protecting vehicle occupants. They have to withstand tensile forces in excess of three tons and simultaneously stretch in a controlled manner in emergencies in order to reduce the load in the event of impact. A seat belt comprises approximately 300 filament yarns, whose individual, high-tenacity yarn threads are spun from around 100 individual filaments.

Invisible, but essential – road reinforcement using geotextiles
But it not just inside vehicles, but also under them, that industrial yarns reveal their strengths. Low stretch, ultra-high tenacity, high rigidity – industrial yarns offer outstanding properties for the demanding tasks carried out by geotextiles; for instance, as geogrids in the base course system under asphalt. Normally, geotextiles have extremely high yarn titers of up to 24,000 denier. Oerlikon Barmag system concepts simultaneously manufacture three filament yarns of 6,000 denier each. Due to the high spinning titers, fewer yarns can be plied together to the required geo-yarn titer in a more cost- and energy-efficient manner.

hycuTEC – technological quantum leap for filter media
In the case of its hycuTEC hydro-charging solution, Oerlikon Neumag offers a new technology for charging nonwovens that increases filter efficiency to more than 99.99%. For meltblown producers, this means material savings of 30% with significantly superior filter performance. For end users, the consequence is noticeably improved comfort resulting from significantly reduced breathing resistance. With its considerably lower water and energy consumption, this new development is also a future-proof, sustainable technology.

New high-tech Staple Fiber Technology Center
Extending to around 2,100 m2, Oerlikon Neumag in Neumünster is home to one of the world’s largest staple fiber technology centers. As of now, these state-of-the-art staple fiber technologies are also available for customer-specific trials.

The focus during the planning and the design of the Technology Center was on optimizing components and processes. Here, special attention was paid to ensuring the process and production parameters in the Technology Center system could be simply and reliably transferred to production systems. Here, the fiber tape processing line is modular in design. All components can be combined with each other as required. And comprehensive set-up options supply detailed findings for the respective process for various fiber products.

The Technology Center is also equipped with two spinning positions for mono- and bi-component processes. The same round spin packs are used for both processes, characterized by excellent fiber quality and properties and meanwhile very successfully deployed in all Oerlikon Neumag production systems. Furthermore, the spinning plant is complemented by automation solutions such as spin pack scraper robots, for example.

• Low impact of Ukraine war on business performance in 1st quarter
• 12.2% increase in sales to €270.9 million based on growth in all four business units
• Adjusted EBITDA improves by 11.5% to €36.8 million

SGL Carbon generated consolidated sales of €270.9 million in Q1 2022 (Q1 2021: €241.5 million). This corresponds to an increase of €29.4 million or 12.2% compared to the same period of the prior year. All four business units contributed to the pleasing increase in sales. In parallel, adjusted EBITDA improved by 11.5% to €36.8 million in the reporting period.

Sales development
In the first three months of fiscal 2022, the sales increase of €29.4 million was driven by all four operating business units: Graphite Solutions (+€11.3 million), Carbon Fibers (+€6.6 million), Composite Solutions (+€7.2 million) and Process Technology (+€6.0 million).
In particular, sales to customers in the automotive and semiconductor industries and a significant recovery in the industrial applications segment were key factors in the increase in sales. Sales of the Process Technology business unit to customers in the chemical industry also developed pleasingly. The effects of the war in Ukraine, which has been ongoing since the end of February 2022, had only a little impact on SGL Carbon's sales performance in the 1st quarter.

Earnings development
Despite the increasingly difficult market environment in the course of Q1 2022, associated with temporary supply and production bottlenecks at their customers, temporarily interrupted transport routes, and significantly higher energy prices, SGL Carbon was able to keep the adjusted EBITDA margin almost stable year-on-year at 13.6%.  
Adjusted EBITDA increased by 11.5% to €36.8 million in the reporting period. Higher capacity utilization in the business units and product mix effects contributed to the improvement in earnings, together with the cost savings achieved as a result of the transformation. By contrast, higher raw material, energy and logistics costs as of end of February 2022 had a negative impact on earnings. The Carbon Fibers business unit was particularly affected by the energy price increases. One-time expenses of €9.2 million in conjunction with energy transactions burdened the Carbon Fibers business unit in the 1st quarter of 2022.  
To secure our production and delivery capabilities, around 85% of the energy requirements of the entire SGL Carbon for 2022 are price-hedged.
Adjusted EBITDA and EBIT do not include in total positive one-time effects and special items of €8.5 million, among other things from the termination of a heritable building right to a site no longer in use. Taking into account the one-time effects and special items presented as well as depreciation and amortization of €14.1 million, reported EBIT increased by 83.5% to €31.2 million (Q1 2021: €17.0 million). The net profit for the period developed correspondingly and more than tripled from €6.1 million to €21.4 million in a quarter-on-quarter comparison.

Outlook
The sales and earnings figures for the 1st quarter 2022 confirm the stable demand from different market segments. Price increases and volatility in the availability of raw materials, transportation services and energy were largely offset by savings from the transformation program and pricing initiatives at the customers.
For 2022, SGL Carbon continues to expect volatile raw material and energy prices, which were included in their forecast for 2022 at the time of planning. However, there are uncertainties about the extent and duration to which SGL Carbon and the customers will be affected by the impact of the war in Ukraine or temporary supply chain disruptions due to the lockdowns in China. Therefore, SGL Carbon's outlook for fiscal 2022 does not include supply and/or production interruptions at customers or the impact of a possible energy embargo that cannot be estimated at this time.  
SGL Carbon's forecast also implies that factor cost increases can be at least partially passed on to the customers through pricing initiatives. SGL Carbon has also included the revenue and earnings impact from the expiry of a supply contract with a major automobile manufacturer at the end of June 2022 in our forecast.

Sicomin has confirmed that eco-surfboard specialist NOTOX will use GreenPoxy 56 in its latest line of R-CARBON boards. The new NOTOX R-CARBON boards are the first to use 100% upcycled carbon fibre fabrics recovered from a production waste stream at Airbus.

NOTOX, founded in 2006 and based in Basque, France, has partnered with Sicomin to use GreenPoxy bio-resins in several earlier flax, cork, and bamboo reinforced boards. In a quest to now produce the most sustainable carbon fibre reinforced boards possible, NOTOX has signed a formal agreement with Airbus Nantes to purchase defective carbon fabrics that were destined for landfill.

The new NOTOX technology gives a second life to Airbus carbon fabrics that are declared unusable for aerospace applications due to short roll lengths, an inability to be pre-formed, or other defects. The upcycled materials are combined with Sicomin GreenPoxy 56 and Surf Clear hardener, producing an extremely clear, high gloss laminate with high mechanical properties. NOTOX use a precisely controlled wet lamination process with vacuum bag consolidation to wet out the upcycled woven carbon fabrics and minimise resin consumption in the manufacturing process.

In addition to selecting a high bio-content resin – GreenPoxy 56 derives 56% of its carbon content from plant sources – NOTOX has also sourced the most sustainable carbon fibre fabrics. Full life cycle analysis by NOTOX has shown that using waste carbon fabrics from Airbus is significantly more energy efficient than using other recycled short fibre carbon, confirming the importance of upcycling this key raw material.

The Aachen-Dresden-Denkendorf International Textile Conference 2022 as face-to-face event takes place on-site in Aachen on December 1-2, 2022.

There is the opportunity to contribute to the conference program and submit an abstract for a talk or poster presentation. The Call for Abstracts for oral presentations ends on May 6, 2022. The Call for Abstracts for poster contributions is open until July 31, 2022.

The ADD-ITC is a conference for experts from the fields of
·    Textile chemistry, finishing & functionalization
·    Synthetic Fibers & Materials
·    Machinery, Processes & Composites

The conference program includes plenary lectures and themed sessions in the areas of
·    Sustainability in the textile industry
·    Future of textile production
·    Textiles for medicine and health
·    Smart textiles & fashion
·    Historic textiles
·    Technology transfer (IGF-ZIM projects)
·    Textile developments by start-ups
 

Further information about the conference program, plenary and keynote speakers as well as the call for abstracts are online availabel.

BB Engineering GmbH (Germany), a subsidiary of Oerlikon Textile, is pleased to announce that Thai Polyester Co., Ltd (Thailand) has placed a major order for four VacuFil systems for recycling bottle flakes with connected direct spinning. The polyester manufacturer, established in 2001 and with an overall annual capacity of 316,800 tons, is one of Thailand’s leading producers and exclusively uses German technology. To this end, the company already operates Oerlikon Barmag and Oerlikon Neumag systems. The BB Engineer-ing VacuFil systems will be deployed to convert existing spinning plant equipment from processing polyester to processing PET bottle flakes without loss of performance.

BB Engineering supplies the complete recycling process – from the drying stage and extrusion, all the way through to the spinning plant-appropriate fine filtration stage. Thanks to decades of experi-ence in spinning plant technology, the German machine construc-tor also provides comprehensive spinning plant know-how and is aware of how the recycling process must be designed to ensure that the product manufactured using the spinning plant ultimately has the right quality. The four new VacuFil systems will be integrated into the existing building infrastructure and process landscape at Thai Polyester, with a total output of approx. 4,000 kg/h. The Vacu-Fil systems will be complemented by BB Engineering 3DD mixers for directly feeding dyes into the recycled melt flow. Commissioning has been scheduled for 2023.

Thai Polyester will be using the new VacuFil systems to manufac-ture its ‘EcoTPC’ recycling-brand yarns. 100% of these polyester yarns are produced from bottle, fiber and yarn waste and are all GRS certified.

• Carbios has succeeded in producing a 100% enzymatically recycled white PET fiber from colored textile waste
• At the same time, the company has produced the first 100% recycled PET bottles, that have successfully passed the food contact validation tests, from the same textile waste.
• Carbios received €827,200 for the validation of this final technical stage of the project co-funded by ADEME

Carbios announced the validation of the 3^rd and final technical step of the CE-PET research project, co-funded by ADEME3 (France’s Environment and Energy Management Agency), for which Carbios is the lead partner alongside its academic partner TWB. This achievement confirms, once again, the full potential and breadth of Carbios’ enzymatic recycling process, C-ZYME™. This breakthrough innovation makes it possible to produce a wide variety of products of equivalent quality to those of petro-sourced origin from any PET waste, including textiles.
 
The first white PET fiber recycled enzymatically from colored textile waste
Worldwide, around 90 million tons of PET are produced each year, more than 2/3 of which are used to manufacture fibers. However, only 13% of textile waste is currently recycled, mainly for downcycling, i.e. for lower quality applications (such as padding, insulators or rags). By successfully manufacturing at pilot scale a white PET fiber that is 100% enzymatically recycled from colored textile waste, Carbios is paving the way for the circular economy in the textile industry.  C-ZYME™ is now on the doorstep of industrialization and will soon enable the biggest brands to move closer to their sustainability goals.
 
Emmanuel Ladent, Chief Executive Officer of Carbios: « Thanks to our breakthrough process, it will soon be possible to manufacture, on a large scale, t-shirts or bottles using polyester textile waste as raw material. This is a major breakthrough that gives value to waste that currently has little or no value. It is a concrete solution that opens up a global market of 60 million tons per year of potential raw materials and will help to reduce the use of fossil resources. »
 
Separate collection of textile waste soon to be mandatory in Europe
From 1 January 2025 the separate collection of textile waste, which is already in place in some countries, will be mandatory for all EU Member States (European Directive 2018/851 on waste).  Carbios’ process will enable this waste to be sustainably recovered and included in a true circular economy model.
 
These technological validations were carried out as part of the CE-PET research project, co-funded by ADEME3. In particular, the project aimed to develop Carbios’ enzymatic PET recycling process on textile waste. The C-ZYME™ technology is complementary to thermomechanical recycling and will make it possible to process plastic and textile waste deposits that are currently not or poorly recovered. For the validation of this stage of the project, Carbios received €827,200 (€206,800 in grants and €620,400 in repayable advances).