From the Sector

Reset
18 results
08.09.2022

Monforts at ITMA ASIA + CITME

Monforts will highlight its technologies for special technical textile applications at this year’s ITMA ASIA + CITME which takes place at the National Exhibition and Convention Center in Shanghai, China, from November 20-24.

One of Monforts' developments is the Montex 8500 XXL stenter system for the production of technical fabrics in widths of up to 6.8 metres. Among the products made on this system are treated nonwovens for the geotextiles and filter media markets, tarpaulins, advertising banners, black-out curtains, membranes and many more.

On Montex©Coat coating lines, meanwhile, the possibilities range from the single-sided application of finishing agents for outdoor clothing and adding functionality to home textiles, to the creation of materials for sophisticated lightweight construction and automotive and aerospace components.

Monforts will highlight its technologies for special technical textile applications at this year’s ITMA ASIA + CITME which takes place at the National Exhibition and Convention Center in Shanghai, China, from November 20-24.

One of Monforts' developments is the Montex 8500 XXL stenter system for the production of technical fabrics in widths of up to 6.8 metres. Among the products made on this system are treated nonwovens for the geotextiles and filter media markets, tarpaulins, advertising banners, black-out curtains, membranes and many more.

On Montex©Coat coating lines, meanwhile, the possibilities range from the single-sided application of finishing agents for outdoor clothing and adding functionality to home textiles, to the creation of materials for sophisticated lightweight construction and automotive and aerospace components.

“Many more applications are possible, such as the overdyeing of denim, the creation of double-face coated materials, fabrics awnings, tents and medical drapes and the pre-treatment of substrates for digital printing”, explains Gunnar Meyer, Monforts area sales manager for China. “A range of different doctor blades and their combinations can be supplied to meet individual requirements, including air knife, roller knife, foam, screen and magnetic roller coating. The latter option is recommended for lines with working widths of over 2.4 metres.”

In addition, Monforts can provide the necessary explosion-proof ranges for solvent-based coatings and high temperature processes up to 320°C, such as the PTFE coating of nonwoven filter material. These lines are equipped with special burners, stenter chains, and insulation.

Source:

 A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

03.08.2022

17. Chemnitzer Textiltechnik-Tagung (CTT) am 28. + 29. September

Unter dem Motto „Textiltechnik als Schlüsseltechnologie der Zukunft“ informieren sich Maschinenproduzenten, Anwender, Textilfachleute und Forschende über neueste Entwicklungen in den Themenbereichen:

  • Ressourceneffiziente und nachhaltige Prozesse
  • Textiltechnologien für den Leichtbau
  • Digitalisierung in der textilen Produktion
  • Additive Fertigung mit Fasern und Textilien

Das Format bietet neben klassischen Vorträgen im Plenarteil und vier Themenkomplexen auch Pitches sowie studentische und wissenschaftliche Projektvorstellungen bzw. Exponate-Präsentationen.

Im Plenarteil der Veranstaltung werden der europäische GFK-Markt vorgestellt und die Bedeutung des Mittelstandes für die deutsche Volkswirtschaft näher beleuchtet.

Ausgewählte technologische Highlights der Fachvorträge in diesem Jahr sind neuartige Verfahren zum 3D-Druck, innovative Carbon-Textilien für die Betonarmierung sowie neue Digitalisierungsstrategien für den Maschinenbau und die Textilindustrie.

Kooperationspartner der diesjährigen Veranstaltung sind das tschechische Generalkonsulat und tschechische Branchenverbände.

Unter dem Motto „Textiltechnik als Schlüsseltechnologie der Zukunft“ informieren sich Maschinenproduzenten, Anwender, Textilfachleute und Forschende über neueste Entwicklungen in den Themenbereichen:

  • Ressourceneffiziente und nachhaltige Prozesse
  • Textiltechnologien für den Leichtbau
  • Digitalisierung in der textilen Produktion
  • Additive Fertigung mit Fasern und Textilien

Das Format bietet neben klassischen Vorträgen im Plenarteil und vier Themenkomplexen auch Pitches sowie studentische und wissenschaftliche Projektvorstellungen bzw. Exponate-Präsentationen.

Im Plenarteil der Veranstaltung werden der europäische GFK-Markt vorgestellt und die Bedeutung des Mittelstandes für die deutsche Volkswirtschaft näher beleuchtet.

Ausgewählte technologische Highlights der Fachvorträge in diesem Jahr sind neuartige Verfahren zum 3D-Druck, innovative Carbon-Textilien für die Betonarmierung sowie neue Digitalisierungsstrategien für den Maschinenbau und die Textilindustrie.

Kooperationspartner der diesjährigen Veranstaltung sind das tschechische Generalkonsulat und tschechische Branchenverbände.

Source:

Förderverein Cetex Chemnitzer Textilmaschinenentwicklung e.V.

(c) ITM
22.06.2022

ITM: Techtextil Innovation Award 2022 für neuartige textile Herzklappenprothesen

Wissenschaftler:innen vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden sind am 21. Juni 2022 für ihre gewebten Herzklappenimplantate mit dem Techtextil Innovation Award 2022 in der Kategorie „New Product“ ausgezeichnet worden.

Im Rahmen eines Forschungsprojektes der Industriellen Gemeinschaftsforschung (IGF) entwickelten Wissenschaftler:innen des ITM neuartige textile Herzklappenprothesen. Die Implantate können exakt an die anatomische Form angepasst und minimalinvasiv im Herz platziert werden. Die textile Herzklappe ist integral gefertigt. Hierbei erfolgt die Integration des Ventils in situ während des Webprozesses. Somit besteht die strömungstechnisch optimierte Herzklappe aus einer einzigen textilen Struktur. Weitere Fügeprozesse, z. B. durch Nähen, sind nicht mehr erforderlich. Das reduziert den Fertigungsaufwand im Gegensatz zur heutigen Herstellung biologischer Herzklappenprothesen in Handarbeit enorm.

Wissenschaftler:innen vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden sind am 21. Juni 2022 für ihre gewebten Herzklappenimplantate mit dem Techtextil Innovation Award 2022 in der Kategorie „New Product“ ausgezeichnet worden.

Im Rahmen eines Forschungsprojektes der Industriellen Gemeinschaftsforschung (IGF) entwickelten Wissenschaftler:innen des ITM neuartige textile Herzklappenprothesen. Die Implantate können exakt an die anatomische Form angepasst und minimalinvasiv im Herz platziert werden. Die textile Herzklappe ist integral gefertigt. Hierbei erfolgt die Integration des Ventils in situ während des Webprozesses. Somit besteht die strömungstechnisch optimierte Herzklappe aus einer einzigen textilen Struktur. Weitere Fügeprozesse, z. B. durch Nähen, sind nicht mehr erforderlich. Das reduziert den Fertigungsaufwand im Gegensatz zur heutigen Herstellung biologischer Herzklappenprothesen in Handarbeit enorm.

Prof. Chokri Cherif, Institutsdirektor des ITM, freut sich mit seinem Team sehr über die kontinuierli-chen interdisziplinären Forschungserfolge, die am ITM in enger Kooperation mit technischen Webereien, Medizinern und Anwendern stetig erzielt werden. „Bereits vor zwei Jahren wurden wir mit dieser neuartigen Entwicklung als eines der drei Finalistenteams des Otto von Guericke-Preises 2020 geehrt. Die Auswahl für den Techtextil Innovation Award 2022 ist eine erneute Bestätigung für den Bedarf an unserer praxisorientierten Forschung und eine besondere Würdigung, aber gleichzeitig auch weiterer Ansporn für die zeitnahe Umsetzung unserer Forschungsergebnisse in die Industrie.“

Bislang stehen für die Behandlung defekter Herzklappen mechanische und biologische Klappen zur Verfügung. Die neuartigen gewebten Herzklappenprothesen sollen die Vorteile der beiden Typen vereinen: unbegrenzte Lebensdauer, keine lebenslange Einnahme von blutverdünnenden Medikamenten und minimal invasive Operation. Ferner können die textilen Herzklappen zeit- und kostensparend mit hoher Reproduzierbarkeit und Qualität gefertigt werden.

05.05.2022

Monforts at Techtextil showcasing its finishing and coating technologies

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

Energy prices are rising steeply everywhere and a particular emphasis for Monforts in Frankfurt will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as better insulation of the treatment chambers or the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air resulting in a radical reduction in the conventional heat supply required compared to gas and thermal oil heating. The modular system for heat recovery can also be extended for exhaust air cleaning and odour elimination. Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation including modification of the heating source.

With the Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

All of these very different materials require coating and finishing for maximum efficiency, using Monforts technologies which provide the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

The Monforts EcoApplicator offers further potential for sustainably achieving perfect finishes via a precise direct application system, as an alternative to conventional padding – where fabrics are immersed in a bath of the required finishing chemicals. It can significantly further reduce the energy and water required and finishes can be applied on just one side of the fabric, or both, and even separately on each side, to be sealed in place via different heating zones in the stenter.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

31.03.2022

Monforts at Techtextil North America

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Advanced machine operation
With the highly intuitive Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Versatility is the key
Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

Source:

AWOl Media / A. Monforts Textilmaschinen GmbH & Co. KG

14.10.2021

Monforts: Automated finishing at Knopf’s Sohn

Knopf’s Sohn, a contract finisher of technical textiles, has installed a fully automated Montex stenter at its plant in Helmbrechts, Germany.
Knopf’s Sohn is processing technical textiles for the automotive, aerospace, home furnishings and workwear markets, based on wool, cellulose, polyamide and polyester fabrics, along with elastane blends, in weights of 80-800gsm.

The Montex machinery range is constantly being upgraded to meet evolving customer needs for greater automation, ease of operation and energy optimisation. The latest ten chamber line at Knopf’s Sohn, with a working width of up to 2.0 metres, was engineered to specific requirements in order to accelerate the company’s move to fully automatic control of its production, and high scaffolding was required for its installation.

The line benefits from two integrated ECO Booster modules to provide high energy savings. These compact, air-to-air heat exchangers, installed within the roof structure of the line, exploit energy from the exhaust gas to preheat up to 60% of the incoming fresh air entering the stenter.

Knopf’s Sohn, a contract finisher of technical textiles, has installed a fully automated Montex stenter at its plant in Helmbrechts, Germany.
Knopf’s Sohn is processing technical textiles for the automotive, aerospace, home furnishings and workwear markets, based on wool, cellulose, polyamide and polyester fabrics, along with elastane blends, in weights of 80-800gsm.

The Montex machinery range is constantly being upgraded to meet evolving customer needs for greater automation, ease of operation and energy optimisation. The latest ten chamber line at Knopf’s Sohn, with a working width of up to 2.0 metres, was engineered to specific requirements in order to accelerate the company’s move to fully automatic control of its production, and high scaffolding was required for its installation.

The line benefits from two integrated ECO Booster modules to provide high energy savings. These compact, air-to-air heat exchangers, installed within the roof structure of the line, exploit energy from the exhaust gas to preheat up to 60% of the incoming fresh air entering the stenter.

The use of a single ECO Booster unit has been calculated to save up to 35% in energy costs, based on fixation processes. Fully automatic operation, set at the Monforts Qualitex control unit, ensures there is no additional burden on the machine operator.

The line is powered by Exxotherm indirect heating, which practically eliminates the yellowing which can be experienced during the treatment of certain polyamide and elastane-based fabrics, and is also equipped with a Conticlean circulating air filter system for constant high drying capacity.

Software
The latest Qualitex visualisation software offers operators reliability and easy control with its full HD multi-touch monitor and slider function, dashboard function with individual adaptation to operating states and faster access to comprehensive recipe data management.

With the Monformatic control system, the exact maintenance of the dwell time in combined treatment processes (drying and heat-setting) can be monitored. When the heat-setting point is reached, the fan speed is automatically adjusted, keeping energy consumption fully under control.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

Oerlikon Webinar with a Focus on Customer Service (c) Oerlikon
19.08.2021

Oerlikon Webinar with a Focus on Customer Service

The new series of webinars of the Swiss Oerlikon Group’s Manmade Fibers Solutions business unit will be focusing on services for manmade fiber systems.

Short Overview of the webinars:

  • How ceramics within the yarn path improve the quality of your yarn on September 01
  • myOerlikon – tailored digital services provide a comprehensive overview on September 13
  • Always by your side – with Oerlikon Remote Services on September 22
  • Better safe than sorry – maximize productivity and minimize downtimes with regular machine check-ups on September 29

For more information click here, where we keep you informed about upcoming events.

The new series of webinars of the Swiss Oerlikon Group’s Manmade Fibers Solutions business unit will be focusing on services for manmade fiber systems.

Short Overview of the webinars:

  • How ceramics within the yarn path improve the quality of your yarn on September 01
  • myOerlikon – tailored digital services provide a comprehensive overview on September 13
  • Always by your side – with Oerlikon Remote Services on September 22
  • Better safe than sorry – maximize productivity and minimize downtimes with regular machine check-ups on September 29

For more information click here, where we keep you informed about upcoming events.

Source:

Oerlikon

04.12.2020

VDMA continues technology webtalks

  • Webtalk on Technologies for Technical Textiles

The next VDMA technology webtalk is scheduled for 9th December 2020, 2.00 pm – 4.00 pm (CET). The topic will be “Technologies for Technical Textiles”.

The presenters and their topics at a glance:

Bena Manasieva Cavus from company Georg Sahm, will show how to add value and performance to your technical yarns with a single end extrusion coating line. Title of the presentation: “Winding and Yarn coating of Technical Textiles”

Janpeter Horn and Dennis Behnken, HERZOG Flechtmaschinen will present new developments in technical braids such as rope braiding/tension members to replace steel wire, medical braids for stents, ligaments, sutures and composites for lightweight construction and near net-shape preforms. Title of the presentation: “New Developments in Technical Braids”

  • Webtalk on Technologies for Technical Textiles

The next VDMA technology webtalk is scheduled for 9th December 2020, 2.00 pm – 4.00 pm (CET). The topic will be “Technologies for Technical Textiles”.

The presenters and their topics at a glance:

Bena Manasieva Cavus from company Georg Sahm, will show how to add value and performance to your technical yarns with a single end extrusion coating line. Title of the presentation: “Winding and Yarn coating of Technical Textiles”

Janpeter Horn and Dennis Behnken, HERZOG Flechtmaschinen will present new developments in technical braids such as rope braiding/tension members to replace steel wire, medical braids for stents, ligaments, sutures and composites for lightweight construction and near net-shape preforms. Title of the presentation: “New Developments in Technical Braids”

Hagen Lotzmann: "At KARL MAYER we work closely with our customers to offer the best cost–benefit ratio. We do this by using our advanced standard platforms as the basis for developing customised solutions." Title of the presentation: “Engineered solutions for technical textiles and composites – from standard application machines to customized systems”

After the presentations, the three experts will be available to answer the participants' questions. Registration is possible.

Source:

VDMA e.V. Textilmaschinen

Coating expertise brings sustainable comfort and convenience to the face mask (c) A. Monforts Textilmaschinen GmbH & Co. KG
The masks are based on 100% woven cotton and the active ingredients in the finish are a reaction mass of titanium dioxide and silver chloride
21.09.2020

Coating expertise brings sustainable comfort and convenience to the face mask

  • Gorilla Protect is a new company formed in May this year to promote the Catus face mask – a major leap forward in the effectiveness of personal protection products that are available to consumers in the fight against Covid-19.
  • Behind Catus and the new company is Nova Textil, the established fabric finishing company based in Grefrath, Germany, and now run by father and son team Rainer and Oliver Hurtz.

Single stenter

Rainer Hurtz founded Nova Textil with a single Monforts Montex stenter and just five employees in 1999 and has steered its constant development and growth over the past twenty years.

“Our initial focus was on the coating of mainly glass fibre fabrics, awnings and sun protection products for outdoor furnishings,” he said. “We had a great customer who was providing us with so many orders that by 2005 we took the decision to order a second Montex stenter, in a special configuration. This also allowed us to enter the market for blackout and digital printing fabrics. We’ve had a great ongoing relationship with Monforts from the beginning.”

  • Gorilla Protect is a new company formed in May this year to promote the Catus face mask – a major leap forward in the effectiveness of personal protection products that are available to consumers in the fight against Covid-19.
  • Behind Catus and the new company is Nova Textil, the established fabric finishing company based in Grefrath, Germany, and now run by father and son team Rainer and Oliver Hurtz.

Single stenter

Rainer Hurtz founded Nova Textil with a single Monforts Montex stenter and just five employees in 1999 and has steered its constant development and growth over the past twenty years.

“Our initial focus was on the coating of mainly glass fibre fabrics, awnings and sun protection products for outdoor furnishings,” he said. “We had a great customer who was providing us with so many orders that by 2005 we took the decision to order a second Montex stenter, in a special configuration. This also allowed us to enter the market for blackout and digital printing fabrics. We’ve had a great ongoing relationship with Monforts from the beginning.”

A third Montex stenter line was installed at the company’s Grefrath plant in 2015, by which time the company had grown to 40 people and a major new market had opened up in the supply of fabrics for promotional materials at exhibitions and trade shows.

“We had a fantastic two years in 2018 and 2019 and everything was going great for the first three months of this year, but in April it all came crashing down,” said Oliver Hurtz. “Coronavirus put an end to trade shows in 2020, which had a very serious impact on our business.”

At the same time, however, the company was exploring the potential of a new biocidal product from one of its chemicals suppliers which has both antiviral and antimicrobial properties.

Filtration

“We had already been producing coated fabrics for hot gas filtration and realised that in combination with this new microporous coating we had the basis for a very effective single-layer face mask,” Rainer said. “Achieving this with a single layer product rather than the usual three has resulted in a significant advance in comfort for the wearer and because the mask is able to disinfect itself and helps regulate humidity, it can be worn a number of times without needing to be washed, for greater convenience. It only needs to be washed when it gets dirty and can also be washed up to twenty times without losing its properties, which has to be preferable to single-use disposables.”

Catus face masks are based on 100% woven cotton and the active ingredients in the finish are a reaction mass of titanium dioxide and silver chloride certified to ISO 20743 for their antibacterial effect, and to ISO 18184 for their antiviral effect.

They are proven to  eliminate over  99.99% of the human coronavirus 229 E, with the multiplication of microorganisms such as germs and bacteria prevented by the biostatic action of silver salts and viruses destroyed by oxygen-releasing substances and a mechanism that attacks their fatty envelope. The virus membrane loses its cholesterol content and the virus is inactivated.

Colours

Gorilla Protect next plans to make the masks available in four colours – black, Bordeaux, olive and grey – and is also working on colour branding and printing labels.

“It’s not possible to print on the surface of the mask after it has been coated, but its is possible for volume orders to be printed before the treatment,” Oliver Hurtz said.

“Face masks are going to become an established part of life in the West like they are in Asia and need to be as comfortable and convenient as possible for the wearer,” his father concluded. “With these things in mind, we believe Catus is a significant step forward.”

New Monfortex line part of a long-term vision for Kettelhack (c) Monforts
The Monfortex sanforizing line with integrated Qualitex 800 control has now been operational at Kettelhack’s plant in Rheine, Westphalia, for a number of months.
24.08.2020

New Monfortex line part of a long-term vision for Kettelhack

  • Kettelhack GmbH – a German leader in the dyeing and finishing of monochrome fabrics for high-quality and durable workwear and bed linen – has this year retired its existing Monforts sanforizing line after 35 years of daily service, replacing it with a new one.

The first line was installed in 1985 during a decisive time for the company.

Taking the helm in the early 1980s, Jan Kettelhack – the current CEO, owner and great grandson of Heinrich Kettelhack who founded the company back in 1874 – made a number of decisions that have secured its success over the following decades.

In 1982 Kettelhack had to vacate its existing plant in the city of Rheine due to urban development restrictions and despite a general sense of crisis in the European textile industry at that time, opted to relocate and build a new highly automated plant that was not reliant on mechanical and personnel-intensive processes. This was aligned with a greater focus on competitive international sales.

  • Kettelhack GmbH – a German leader in the dyeing and finishing of monochrome fabrics for high-quality and durable workwear and bed linen – has this year retired its existing Monforts sanforizing line after 35 years of daily service, replacing it with a new one.

The first line was installed in 1985 during a decisive time for the company.

Taking the helm in the early 1980s, Jan Kettelhack – the current CEO, owner and great grandson of Heinrich Kettelhack who founded the company back in 1874 – made a number of decisions that have secured its success over the following decades.

In 1982 Kettelhack had to vacate its existing plant in the city of Rheine due to urban development restrictions and despite a general sense of crisis in the European textile industry at that time, opted to relocate and build a new highly automated plant that was not reliant on mechanical and personnel-intensive processes. This was aligned with a greater focus on competitive international sales.

From 1986, the company’s proficiency as a specialist in solid-colour textiles led to workwear textiles becoming a bedrock of the business. Continuous investments in machinery and technical equipment have resulted in a fully integrated and rationalised single source site dedicated solely to what the company does best – the expert dyeing and finishing of textiles.

Crucial process steps

These stages in the textile value-added chain, Jan Kettelhack has observed, are crucial to the quality of a final product in workwear – whether it stands the test in everyday use, how comfortable it is, and how many washes it can withstand.

Central to this is the sanforizing process, which pre-shrinks a fabric by compressing it prior to washing. This limits any residual or further shrinkage in a made-up finished garment to less than 1%, to ensure perfect comfort and fit over an extended lifetime.

“We certainly can’t complain about the performance of the old Monfortex sanforizing line which gave us so many uninterrupted years of service, but certain spare parts for it were becoming increasingly hard to source, the control unit was becoming a little unstable and we couldn’t risk potential interruptions to our production schedule,” says Kettelhack plant manager Hendrik Pleimann. “In many ways, the new Monfortex sanforizer is much the same as the old one in terms of its mechanical reliability and robust construction, but of course today’s drives are much more efficient, and when it comes to the automation features and control units – and the data we can generate and analyse for increasing efficiency – that’s a whole new world.”

Qualitex 800

The two-metres-wide Monfortex line benefits from the latest Qualitex 800 control system which allows all parameters to be easily automated via the 24-inch colour touchscreen, including production speed, control of all fabric feed devices, rotation spray or steaming cylinder options, the width of the stretching field and the rubber belt pressure.

The integrated Compactomat system allows a continuous indication and control of the shrinkage values and the temperatures of the shrinking cylinder and felt calender. Up to 10,000 separate process parameter records can be generated and stored by the data manager.

Full line management can be optimised via the batch-specific calculation of all process material consumption and water and electricity use, with any standstill times analysed and immediately corrected for the future.

Any further assistance required is available via Monforts Teleservice, with direct connection to technicians and virtual access to machine analysis.

Professional

Commissioning of the new Monfortex line at Kettelhack commenced in January and it was fully operational in a relatively short time.

“This was a very professional installation provided by the Monforts team with whom we have a very good relationship dating back many years, and everyone knew what was required from both sides,” says Mr Pleimann. “Our operators have found the new line very user friendly and we are very pleased with how everything proceeded so smoothly. An unexpected benefit is that the new line is also a lot quieter, of course, which is something our operatives are appreciating.”

Key features of the Monfortex line are the proven fabric preparation, weft straightening and spreading units, prior to the compressive shrinkage machine with a 750mm shrinking cylinder, and a felt calender equipped with 2,000mm diameter drying cylinder. The line also features an integrated automatic grinding unit.

Customer service

Kettelhack is processing primarily cotton and polyester woven fabrics, with lyocell becoming increasingly popular in workwear for its softness and comfort.

As part of its customer service, the company stocks more than a million metres of grey fabric and at least 1.2 million metres of finished and rolled standard fabric in its warehouse at any one time, with a further 750,000 metres permanently in production.

While a significant cost, this commitment ensures Kettelhack customers can be fully flexible and rely on it as a partner.

“As a family-run company with around a hundred employees, Kettelhack operates very differently to bigger businesses which have to constantly consider their immediate quarterly profits,” Mr Pleimann concludes. “The thinking at Kettelhack is in terms of the next twenty years and ensuring that the business will be just as successful for the next generation as it is today. We also have a very flat organisational structure in which everyone is involved and takes an active part, which makes it a very nice place to work.”

Source:

On behalf of A. Monforts Textilmaschinen GmbH & Co. KG by AWOL Media.

20.08.2020

Energy efficiency in textile dyeing and finishing - VDMA continues technology webtalks

  • Energy efficiency will be the topic of VDMA’s next edition of Textile Machinery Webtalks on 27 August 2020 (2 pm - 4 pm CEST).  

Efficient energy management is of increasing importance in textile dyeing and finishing. Innovative machine designs with minimal water and energy consumption as well as the recovery and use of the heat energy produced in the processes represent valuable potential savings for any modern company.

The presenters at a glance:

  • Energy efficiency will be the topic of VDMA’s next edition of Textile Machinery Webtalks on 27 August 2020 (2 pm - 4 pm CEST).  

Efficient energy management is of increasing importance in textile dyeing and finishing. Innovative machine designs with minimal water and energy consumption as well as the recovery and use of the heat energy produced in the processes represent valuable potential savings for any modern company.

The presenters at a glance:

  • Ludger Sommer, Thies, will show how to manage heat energy in wetprocessing.
  • Benjamin Schnabel, Brückner Textilmaschinen is going to demonstrate how to make one of the most energy consuming processes in textile manufacturing more sustainable, eco-friendly and cost effective.
  • Fabian Buckenmayer, PLEVA Sensors and Controls will inform about the specific opportunities for an energy-efficient textile production via measuring and controlling process parameters.  

After the presentations, the experts will be available to answer the participants' questions. The webtalk series is very well received by the textile industry. During the first three webtalks, VDMA welcomed almost 900 registered participants from more than 50 countries. Registration is still possible.

Source:

VDMA e. V. Textilmaschinen

 

Sustainable leadership for GtA with new Monforts Montex wide width lines (c) AWOL Media
GtA Managing Director Andreas Niess
27.07.2020

Sustainable leadership for GtA with new Monforts Montex wide width lines

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

A new standard in pure white, 100% clean and fault-free textile substrates has been demanded by this market in recent years due to the rapid growth in digitally-printed banners and billboards – often referred to as ‘soft signage’.

The substrates of choice for digital printing are 100% polyester warp knits which are resilient and allow excellent take-up of inks, and vibrant colours and clear and precise images to be achieved with digital printing techniques. The knitted construction also has the advantage of elasticity, which is a plus in terms of flexibility for installers.

Critically, the warp knitted fabrics have extremely smooth surfaces which is becoming increasingly important due to the general move away from PVC coatings which were the standard in the past.

It was to finish these fabrics for Georg and Otto Friedrich GmbH as well as providing such services for many other customers, that the GtA plant in Neresheim, Baden-Württemberg, was established in 2015.

The purpose-built plant on a greenfield site was initially equipped with a fully-automated, 72 metre long Monforts installation comprising a washing machine integrated with a 3.6 metre wide, seven-chamber Montex stenter. The line quickly went from single to double shift production and then to 24/7 operation  to meet demand.

Expanded widths

Building on the success of this installation, GtA has now installed two more Montex stenter lines – both in expanded working widths of 5.6 metres and purpose-built at Montex GmbH in Austria.

A six-chamber Montex unit is combined with a washing machine to guarantee the purity of the substrates, while a five-chamber line is integrated with a wide-width coating machine. This new coating capability at GtA has led to a number of new additions to the Georg and Otto Friedrich DecoTex range for digital printing, including wide width fabrics with flame retardant, antimicrobial and non-slip finishes.

The new Montex stenter lines benefit from all of the latest innovations from Monforts, including the Smart Sensor system for the optimised maintenance planning of key mechanical wear components on the stenters. A comprehensive overview of the condition of all parts at any time is now available for operators within the highly intuitive Qualitex visualization software.

With Qualitex, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

Environmental commitment

GtA is run by a seasoned team of textile professionals led by Managing Director Andreas Niess.

“We have received excellent service from Monforts from the outset and we were happy to place the order for these two new lines as part of our ongoing cooperation,” he says. “With all of the latest Monforts advances in technology we are fully in control of all production and quality parameters with these lines, as part of our significant commitment to innovative environmental technology.”

The GtA plant, which operates in near-cleanroom conditions, has also been equipped with proprietary technology to fully exploit the Monforts air-to-air heat recovery systems that are now standard with Montex stenters.

“Around 30 per cent of our investment volume at the site goes to energy-saving measures and we are sure that this commitment is worthwhile,” Mr Niess says. “As an example, our integrated heat recovery system fully exploits the waste heat from the process exhaust air and the burner exhaust gases of the Monforts stenters, allowing us to achieve an exhaust air temperature of  between 30 to 34°C, compared to what would conventionally be between 140 to 160°C. Another focus has been on exhaust air purification technology and here too, the latest technology has been installed with integrated heat recovery elements.”

This, he adds, saves 52% of the energy that would normally be used – equating to 5,800,000 KwH per year. The necessary audits for energy-efficient companies are also carried out annually.

In addition, GtA has purpose-designed the automatic chemical mixing and dosing systems that feed the padders for the key treatments that are carried out on the fabrics through the stenters.

The company is going further, however, in its pursuit of clean production and raw materials.

"We want to be an asset and not a burden on our immediate environment and therefore do not use any additives containing solvents," Mr Niess says. “We were the first to use fully halogen-free flame retardant chemistry, and we use bio-based, finely ground alumina products for the washing process instead of surfactants. PES polyester yarns made from recycled material are also increasingly used and the latest additions to our raw materials portfolio, the RC-Ocean products, are made from recycled sea plastic.

“We are now planning a combined heat and power plant for the production of electrical energy and heat and we will also build a photovoltaic system that converts solar radiation into electrical energy. GtA wants to be the first textile finishing company to be CO2-neutral in the manufacture of all of its products by 2025. The complete heat supply and heating for the 13,000 square metre production hall, as well as the office building and the hot water supply for the domestic water, is already energy-neutral. We are convinced that this commitment will pay off in the long term and our positive business development proves that sustainability and business profitability are perfectly compatible.”

In addition to the products for Georg and Otto Friedrich GmbH, GtA  offers its manufacturing capacities for other customers as a contract service.

All products are manufactured in accordance with Öko-Tex Standard 100, product class 1 and the company is also involved in the research and development of new sustainable manufacturing processes, in cooperation with many regional universities and funding project partners.

Source:

AWOL Media for A. Monforts Textilmaschinen GmbH & Co. KG

Monforts at Techtextil India (c) Monforts
A recent Monforts texCoat installation.
20.11.2019

Monforts at Techtextil India

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

As a result, India’s Ministry of Textiles is forecasting that the growth of technical textiles in the country will be over 18% annually in the next few years, from a value of US$16.6 billion in 2018 to US$28.7 billion in 2021.

Value addition

High value-added technical products such as wide-width digital printing substrates, carbon fabrics for high-performance composites, filter media, flame retardant barrier fabrics and heavy-duty membranes are now being coated on Monforts texCoat ranges and finished with the company’s industry-leading Montex stenters.

“Since we acquired the technology that our coating units are based on in 2015, we have made a lot of refinements,” says Hans. “All of these developments are reflected in higher coating accuracy and the resulting quality of the treated fabrics. At the same time, our latest multi-functional coating heads offer an unprecedented range of options, with a wide range of modules available.”

The texCoat user interface is now equipped with the unique Monforts visualisation system and the magnetic doctor blade has greater power reserves. Options include a carbon fibre-reinforced composite coating drum with a more scratch-resistant surface and maximum rigidity and remote control which simplifies exact adjustment for the operator.

Montex stenters in special executions are meanwhile ideal for the drying and finishing of both technical woven fabrics and nonwovens and characterised by high stretching devices in both length and width.

“The European-built Montex range of stenters has earned its leading position in the technical textiles market due to the overall robustness, reliability and economy of these machines,” Hans concludes. “Whatever the intended end-product – and we continue to discover potentially new areas in which technical textiles can be utilised all the time – we have the machine specification and know-how to turn ideas into reality. In India we also benefit from the strong sales and service support of A.T.E. Enterprises.”

Texchtextil India takes place alongside World of Composites at the Bombay Exhibition Centre in Mumbai from November 20-22.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG by AWOL Media.

Die Carbonfaser revolutionieren – RCCF eröffnet Technikum (c) TU Dresden
05.11.2018

Die Carbonfaser revolutionieren – RCCF eröffnet Technikum

  • Mit einem Festakt haben Dr. Eva-Maria Stange, Staatsministerin für Wissenschaft und Kunst des Freistaates Sachsen, Prof. Gerhard Rödel, Prorektor für Forschung der Technischen Universität Dresden, Prof. Hubert Jäger und Prof. Chokri Cherif am 02.11.2018 das Carbonfaser-Technikum des Research Center Carbon Fibers (RCCF) eröffnet.

Das RCCF, eine gemeinsame wissenschaftliche Einrichtung des Instituts für Leichtbau und Kunststofftechnik (ILK) und des Instituts für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden, wurde gegründet, um die Carbonfasern vom Faserrohstoff bis zum fertigen Bauteil zu erforschen und neue Eigenschaften und Anwendungsmöglichkeiten zu entdecken.

  • Mit einem Festakt haben Dr. Eva-Maria Stange, Staatsministerin für Wissenschaft und Kunst des Freistaates Sachsen, Prof. Gerhard Rödel, Prorektor für Forschung der Technischen Universität Dresden, Prof. Hubert Jäger und Prof. Chokri Cherif am 02.11.2018 das Carbonfaser-Technikum des Research Center Carbon Fibers (RCCF) eröffnet.

Das RCCF, eine gemeinsame wissenschaftliche Einrichtung des Instituts für Leichtbau und Kunststofftechnik (ILK) und des Instituts für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden, wurde gegründet, um die Carbonfasern vom Faserrohstoff bis zum fertigen Bauteil zu erforschen und neue Eigenschaften und Anwendungsmöglichkeiten zu entdecken.

„Sachsen verfügt in der Schlüsseltechnologie Werkstoff-, Material- und Nanowissenschaft über hervorragende Rahmenbedingungen und hoch motivierte Wissenschaftler an Hochschulen und Forschungseinrichtungen, die in dieser Spezialisierung weltweit ihresgleichen suchen“, erklärt dazu Staatsministerin Dr. Stange. „Beinahe alle Materialklassen von Metallen, Polymeren, Keramiken bis hin zu Verbund- und Naturwerkstoffen werden auf international hohem Niveau bearbeitet. Dabei greifen Grundlagen- und Angewandte Forschung in zahlreichen Feldern eng ineinander und bilden geschlossene Entwicklungsketten bis zu einem Transfer in die Wirtschaft – regional, national und international.“

Der Prorektor für Forschung der TU Dresden, Prof. Gerhard Rödel, ergänzt: „Mit dem Carbonfaser-Technikum ist im Research Center Carbon Fibers eine weltweit einzigartige Anlage entstanden, die völlig neue Möglichkeiten eröffnet. Es geht darum, Fasern mit einem möglichst hohen Individualisierungsgrad zu designen – je nach Bedarf und Einsatzbereich.“

Auf der derzeit installierten, einzigartigen Anlage erforschen Wissenschaftler des RCCF unter Reinraum-Bedingungen die Grundlagen für maßgeschneiderte Kohlenstofffasern und erschließen deren hohes Innovationspotential. Dabei greifen die Forscher auf einzelne Anlagenmodule zur Stabilisierung und Carbonisierung mit industrienahem Ofendesign und individuell einstellbaren Parameterkombinationen zurück. Durch den außerordentlichen Reinheitsgrad sind die Carbonfasern für die Anforderungen der Luft-/Raumfahrt- und der Automobilindustrie maßgeschneidert.

„Die Carbonfaser ist der Stahl des 21. Jahrhunderts“, führt Prof. Hubert Jäger, Sprecher des Instituts für Leichtbau und Kunststofftechnik (ILK), aus. „Ganze Branchen erfinden sich derzeit durch diesen Werkstoff neu und erreichen mit ihren Produkten nie gedachte Dimensionen. Das Problem ist jedoch die Verfügbarkeit. Wir werden mit dem Carbonfaser-Technikum einen Beitrag dazu leisten, dass aus Sachsen heraus dieser Werkstoff nicht nur leichter verfügbar, sondern auch besser und maßgeschneidert einsetzbar wird für Anwendungen in der Luft- und Raumfahrt, Fahrzeugbau, Architektur und Hochleistungselektronik.“

„Mit der Inbetriebnahme des Carbonfaser-Technikums unter Reinraumbedingungen am RCCF gelingt es uns, die Prozesskette zur Fertigung maßgeschneiderter Kohlenstofffasern signifikant zu erweitern. Die notwendigen Maschinentechniken des ITM einschließlich der bereits gewonnenen Erfahrungen bei Prozessoptimierungen zur Herstellung von Precursorfasern, dem Ausgangsmaterial für die neuen Stabilisierungs- und Carbonisierungslinien, stehen in künftigen Forschungsvorhaben den Wissenschaftlern des RCCF zur Verfügung. Somit geben wir am exzellenten Forschungsstandort Dresden die Initialzündung für die weiterführende Grundlagen- und anwendungsorientierte Forschung auf dem Gebiet der Kohlenstofffasern“, ergänzt Prof. Chokri Cherif, Direktor des ITM und Inhaber der Professur für Textiltechnik.

Das Carbonfaser-Technikum umfasst einen mehr als 300 m² großen Reinraum der Klasse ISO 8. Neben den beiden auf etwa 30 Metern aufgestellten Stabilisierungs- und Carbonisierungslinien sind weitere Flächen für künftige Erweiterungen der Gesamtanlage vorgesehen, zum Beispiel ein weiterer Hochtemperaturofen, in dem Carbonfasern bis zu Temperaturen über 2000°C graphitierbar sind oder unikale Beschichtungsanlagen zur Oberflächenaktivierung.

Die RCCF-Wissenschaftler ergründen die Wechselwirkungen zwischen Prozessparametern, Faserstruktur und weiteren mechanischen, thermischen und elektrischen Eigenschaften bei der Herstellung von Carbonfasern, um die Fähigkeiten des Hightech-Werkstoffes weiter zu steigern. Zusätzlich nehmen die Forscher die Entwicklung multifunktionaler Fasern mit neuartigen Eigenschaftsprofilen wie hohe Leitfähigkeit bei hoher Festigkeit oder ausgeprägter Verformbarkeit sowie die Nutzung erneuerbarer Ausgangsstoffe in den Fokus ihrer Arbeiten.

Ein weiterer Schwerpunkt der RCCF-Aktivitäten ist die tiefgreifende studentische Ausbildung im Bereich der Carbonfaser-Herstellung. Den Studierenden werden dabei fundierte Kenntnisse in Herstellung und Weiterverarbeitung von Carbonfasern vermittelt, damit sie in diesem Bereich der Zukunftstechnologien dem sächsischen und deutschen Arbeitsmarkt zur Verfügung stehen. Etwa 15 Studierende werden pro Jahr in Forschungsbereiche wie die Prozessführung, -modellierung und -überwachung sowie die Entwicklung, Fertigung und Charakterisierung neuer Carbonfasern und Verbundwerkstoffe einbezogen.

More information:
TU Dresden Carbonfaser
Source:

Technische Universität Dresden  - Fakultät Maschinenwesen   
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

 

© ITM/TU Dresden
Erste Ausführung eines multimodalen eGloves: Maßgeschneidertes Musikinstrument mit integrierter Sensorik zur Gestenerkennung und drahtlos angekoppeltem Tonwiedergabesystem sowie integrierter Leuchtfunktion für visuelles Feed-Back.
12.10.2018

ITM in einem Exzellenzcluster der TU Dresden maßgeblich involviert

Wissenschaftler des Instituts für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden in einem der drei bewilligten Exzellenzcluster der TU Dresden maßgeblich involviert   
 
Ende September erfolgte die Bekanntgabe der Förderentscheidung über Exzellenzcluster durch die Deutschen Forschungsgemeinschaft (DFG) im Exzellenz-Wettbewerb. Drei der insgesamt sechs beantragten Exzellenzcluster der TUD wurden im Rahmen der Exzellenzstrategie des Bundes und der Länder bewilligt. Das ITM war im Vorfeld bei der Beantragung der Exzellenzcluster-Vollanträge mehrere Monate sehr stark eingebunden, so dass die Freude bei den Wissenschaftlern am ITM ausgesprochen groß ist, dass das Cluster „Centre for Tactile Internet with Human-in-the-Loop” (CeTI) bewilligt wurde.   
 

Wissenschaftler des Instituts für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden in einem der drei bewilligten Exzellenzcluster der TU Dresden maßgeblich involviert   
 
Ende September erfolgte die Bekanntgabe der Förderentscheidung über Exzellenzcluster durch die Deutschen Forschungsgemeinschaft (DFG) im Exzellenz-Wettbewerb. Drei der insgesamt sechs beantragten Exzellenzcluster der TUD wurden im Rahmen der Exzellenzstrategie des Bundes und der Länder bewilligt. Das ITM war im Vorfeld bei der Beantragung der Exzellenzcluster-Vollanträge mehrere Monate sehr stark eingebunden, so dass die Freude bei den Wissenschaftlern am ITM ausgesprochen groß ist, dass das Cluster „Centre for Tactile Internet with Human-in-the-Loop” (CeTI) bewilligt wurde.   
 
Das „Zentrum für taktiles Internet mit Mensch-Maschine-Interaktion“ der TU Dresden will die Zusammenarbeit zwischen Mensch und Maschine auf eine neue Stufe heben. Menschen sollen künftig in der Lage sein, in Echtzeit mit vernetzten automatisierten Systemen in der realen oder virtuellen Welt zu interagieren. Ab Anfang 2019 arbeiten für dieses Ziel im Exzellenzcluster CeTI Wissenschaftler der TU Dresden aus den Fachgebieten Elektro- und Kommunikationstechnik, Informatik, Maschinenwesen, Psychologie, Neurowissenschaften und Medizin mit Forschern der TU München, des Deutschen Zentrums für Luft- und Raumfahrt und der Fraunhofer-Gesellschaft sowie internationalen Wissenschaftseinrichtungen zusammen. Interdisziplinär erforschen sie Schlüsselbereiche der menschlichen Kontrolle in der Mensch-Maschine-Kooperation, im Soft- und Hardware-Design, bei Sensor- und Aktuatortechnologien sowie bei den Kommunikationsnetzen. Die Forschungen sind Grundlage für neuartige Anwendungen in der Medizin, der Industrie (Industrie 4.0, Co-working) und dem ‘Internet der Kompetenzen‘ (Bildung, Rehabilitation).   
 
Sprecher von CeTI ist Herr Professor Frank Fitzek, Inhaber der Deutschen Telekom Professur für Kommunikationsnetze am Institut für Nachrichtentechnik der TU Dresden.
 
Das ITM wird innerhalb von CeTI seine umfassenden Expertisen auf dem Gebiet der Entwicklung maßgeschneiderter Funktionsmaterialien und -textilien einbringen. Hierbei werden sogenannte eGloves und eBodySuits, also elektronische Handschuhe und Anzüge, entwickelt, die strukturintegrierte faserbasierte Sensor-, Aktor- und Leitungssysteme sowie Verbindungselemente zu weiteren elektronischen Komponenten beinhalten. Derartige eGloves und eBodySuits bilden dabei eine neuartige multimodale Schnittstelle zwischen Mensch und Maschine, indem sie visuelle, akustische und haptische Informationen aufnehmen, interpretieren und zurückgegeben können.  

 

More information:
ITM
Source:

Technische Universität Dresden
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

19.06.2018

Dresdner Wissenschaftlerin mit Manfred-Hirschvogel-Preis 2018 geehrt

Frau Dr.-Ing. Iris Kruppke, wissenschaftliche Mitarbeiterin am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden, wurde am 16. Juni 2018 zum Tag der Fakultät Maschinenwesen der TU Dresden mit dem Manfred-Hirschvogel-Preis geehrt. Der Preis ist mit 5.000 EUR dotiert und wird seit 2013 jährlich an allen TU9-Universitäten - den neun führenden technischen Universitäten in Deutschland - für die beste Promotion des zurückliegenden Jahres im Bereich Maschinenbau vergeben.

Frau Dr.-Ing. Iris Kruppke, wissenschaftliche Mitarbeiterin am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden, wurde am 16. Juni 2018 zum Tag der Fakultät Maschinenwesen der TU Dresden mit dem Manfred-Hirschvogel-Preis geehrt. Der Preis ist mit 5.000 EUR dotiert und wird seit 2013 jährlich an allen TU9-Universitäten - den neun führenden technischen Universitäten in Deutschland - für die beste Promotion des zurückliegenden Jahres im Bereich Maschinenbau vergeben.

Im Rahmen ihrer Dissertation zum Thema „Entwicklung von Methoden zur Realisierung von maßgeschneiderten Adhäsionseigenschaften von faserbasierten Hochleistungswerkstoffen für Composites“ setzte sich Frau Dr. Kruppke mit der Oxifluorierung als Oberflächenbehandlungs-methode auseinander. Dieses hocheffiziente Verfahren, das zur Oberflächenfunktionalisierung eingesetzt wird, soll zukünftig insbesondere bei der Entwicklung neuer maßgeschneideter Carbonfasern zum Einsatz kommen. Frau Dr. Kruppke gelang es, das Thema der Oxifluorierung zum maßgeschneiderten Grenzschichtdesign von Carbonfasern im Rahmen der großen Forschungsinitiative „C3 - Carbon Concrete Composites“ innerhalb des BMBF-Programms „Zwanzig20 - Partnerschaft für Innovation“ mit starker Industriebeteiligung sehr erfolgreich weiter voran zu treiben.

Die Ergebnisse ihrer Dissertation, die Frau Dr. Kruppke Ende März mit der Bestnote „summa cum laude“ verteidigte, sind von enormer Bedeutung für die Herstellung von Faserverbundwerkstoffen. Sie eröffnen die Möglichkeit, Hochleistungsfasern in Hochleistungsstrukturen umzuwandeln. Solche Entwicklungen erfordern eine Anpassung der vorliegenden Grenzflächen dieser Hochleistungsfasern an neue polymerbasierte, z. B. thermoplastische und anorganische Matrixsysteme. Die besonderen Publikationsleistungen lassen erwarten, dass die bisher erzielten Resultate weiterhin als fester Bestandteil in die zukünftige industrienahe Carbonfaserforschung eingehen und somit ein neues Forschungsgebiet erschließen.

Gerade im wissenschaftlichen Bereich des Maschinenbauwesens sind Frauen in leitender Position bedauerlicherweise immer noch selten zu finden. Mit der erneuten Auszeichnung beweisen die Wissenschaftlerinnen des ITM ihr enormes wissenschaftliches Know-how, welches sie am ITM dank der exzellenten Infrastruktur erlangen und deren Ergebnisse auf renommierten nationalen und internationalen Konferenzen regelmäßig offeriert werden. Bereits 2017 wurde eine weitere Wissenschaftlerin des ITM mit dem Bertha Benz-Preis für ihre herausragende Promotion zur Entwicklung eines neuartigen Verfahrens zur Herstellung metallischer 3D-Strukturen auf Webmaschinen ausgezeichnet.

Manfred Hirschvogel Preis
Die Frank Hirschvogel Stiftung hat 2013 zum ersten Mal den Manfred Hirschvogel Preis verliehen. Der Preis wird zu Ehren des Lebenswerks von Dr. Manfred Hirschvogel vergeben.
Der Preis ist mit 5.000 EUR dotiert und wird seit 2013 jährlich an allen TU9-Universitäten - den neun führenden technischen Universitäten in Deutschland - für die beste Promotion des zurückliegenden Jahres im Bereich Maschinenbau vergeben.

More information:
TU Dresden
Source:

Technische Universität Dresden
Fakultät Maschinenwesen
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

Bundespräsident Frank-Walter Steinmeier und Ehefrau Elke Büdenbender überzeugen sich vom innovativen Carbonbeton bei ihrem Besuch an der TU Dresden © Sven Hofmann
Bundespräsident Steinmeier zu Gast an der TU Dresden
17.11.2017

Bundespräsident Steinmeier zu Gast an der TU Dresden

Dresden - Bundespräsident Frank-Walter Steinmeier besuchte die Preisträger des Zukunftspreises 2016 und den Standort des Carbonbeton in Dresden

Im Rahmen seines zweitägigen Antrittsbesuchs in Sachsen war Bundespräsident Frank-Walter Steinmeier am 14. November 2017 an der TU Dresden zu Gast. Gemeinsam mit seiner Frau Elke Büdenbender informierte er sich vor Ort über den prämierten Zukunftswerkstoff Carbonbeton.

In einer anschaulichen Präsentation informierten die Preisträger des Zukunftspreises 2016 – der Preis des Bundespräsidenten für Technik und Innovation, Professor Chokri Cherif, Direktor des Institutes für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden, der emeritierte Professor Peter Offermann, Vorstandsvorsitzender des Verbandes Tudalit und Beirat im Deutschen Zentrum Textilbeton und Professor Manfred Curbach, Direktor des Institutes für Massivbau der TU Dresden, über das zukunftsträchtige Material Carbonbeton und das dazugehörige Großforschungsprojekt C³ – Carbon Concrete Composite.

Dresden - Bundespräsident Frank-Walter Steinmeier besuchte die Preisträger des Zukunftspreises 2016 und den Standort des Carbonbeton in Dresden

Im Rahmen seines zweitägigen Antrittsbesuchs in Sachsen war Bundespräsident Frank-Walter Steinmeier am 14. November 2017 an der TU Dresden zu Gast. Gemeinsam mit seiner Frau Elke Büdenbender informierte er sich vor Ort über den prämierten Zukunftswerkstoff Carbonbeton.

In einer anschaulichen Präsentation informierten die Preisträger des Zukunftspreises 2016 – der Preis des Bundespräsidenten für Technik und Innovation, Professor Chokri Cherif, Direktor des Institutes für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden, der emeritierte Professor Peter Offermann, Vorstandsvorsitzender des Verbandes Tudalit und Beirat im Deutschen Zentrum Textilbeton und Professor Manfred Curbach, Direktor des Institutes für Massivbau der TU Dresden, über das zukunftsträchtige Material Carbonbeton und das dazugehörige Großforschungsprojekt C³ – Carbon Concrete Composite.

Dabei überzeugte sich das Bundespräsidentenpaar in vertiefenden Gesprächen mit Dresdner Wissenschaftlern von den ökologischen, ökonomischen und gesellschaftlichen Vorteilen des innovativen Verbundwerkstoffes. Mithilfe der zahlreichen Demonstratoren, die das Material von der Entstehung bis zum fertigen Produkt darstellen, konnten die besondere Leichtigkeit und Formbarkeit von Carbonbeton eindrucksvoll veranschaulicht werden.

Die Weichen für den Erfolg des Carbonbetons wurden bereits 1993 von Professor Offermann an der TU Dresden als Erfinder des Textilbetons gestellt. Aus dieser Vision entstand der erste Sonderforschungsbereich, welcher maßgeblich von der Innovation des ITM geprägt war. Gemeinsam haben die drei prämierten Carbonbetonforscher Cherif, Offermann und Curbach die Forschungsaktivitäten zum Einsatz von Carbon als textile Bewehrung im Beton in zahlreichen weiteren interdisziplinären Forschungsprojekten stetig vorangetrieben. Schon seit 2006 werden deutschland- sowie weltweit alte Bauwerke, oder auch riesige Silos mit Carbonbeton verstärkt.

Der Baustoff Carbonbeton stellt also nicht nur eine Innovation für den Standort Dresden dar, sondern wird weltweit immer wichtiger. Darüber hinaus fördert seit 2014 das Bundeministerium für Bildung und Forschung den gegründeten Verein C³ – Carbon Concrete Composite e. V. mit einem Gesamtprojektvolumen von ca. 80 Millionen Euro. Der C³ e. V. ist ein interdisziplinäres Netzwerk aus mehr als 150 Partnern aus den Bereichen Wirtschaft, Wissenschaft und Verbänden, die gemeinsam die Einführung des Materials auf dem Markt vorantreiben. Wissenschaftler des Instituts für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden bearbeiten mehrere Teilvorhaben federführend und sind in weiteren Teilvorhaben maßgeblich als Projektpartner integriert.

Source:

Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden

ITM TU Dresden Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden
ITM TU Dresden
31.05.2017

Leichtbau leicht gemacht – Neuartiges Verfahren ermöglicht die Herstellung superstabiler Metallzellen auf Webmaschinen

Ob im Maschinenbau, in der Automobilindustrie oder der Luft- und Raumfahrt – dem Leichtbau kommt für die Zukunft dieser Industriebereiche eine entscheidende Bedeutung zu. Leichtere und steifere Bauteile bewirken eine Verminderung des Treibstoffverbrauchs und führen zur Einsparung von Treibhausgasen. „In der Verarbeitung von Leichtmetallen wie Aluminium bei Gussverfahren sind wir heute allerdings an der Grenze des physikalisch Möglichen angelangt“, erläutert Cornelia Sennewald, Ingenieurin an der Fakultät Maschinenwesen der Technischen Universität Dresden. „Der nächste Qualitätssprung zu noch einmal deutlich leichteren und dabei 2 zugleich stabileren Strukturen führt über die Herstellung sogenannter metallischer Zellen. Dabei werden Drähte so ineinander verwoben, dass superfeste Verbindungen bei gleichzeitig minimalem Materialeinsatz entstehen.“

Ob im Maschinenbau, in der Automobilindustrie oder der Luft- und Raumfahrt – dem Leichtbau kommt für die Zukunft dieser Industriebereiche eine entscheidende Bedeutung zu. Leichtere und steifere Bauteile bewirken eine Verminderung des Treibstoffverbrauchs und führen zur Einsparung von Treibhausgasen. „In der Verarbeitung von Leichtmetallen wie Aluminium bei Gussverfahren sind wir heute allerdings an der Grenze des physikalisch Möglichen angelangt“, erläutert Cornelia Sennewald, Ingenieurin an der Fakultät Maschinenwesen der Technischen Universität Dresden. „Der nächste Qualitätssprung zu noch einmal deutlich leichteren und dabei 2 zugleich stabileren Strukturen führt über die Herstellung sogenannter metallischer Zellen. Dabei werden Drähte so ineinander verwoben, dass superfeste Verbindungen bei gleichzeitig minimalem Materialeinsatz entstehen.“


Die noch junge Werkstoffklasse der sogenannten zellularen metallischen Materialien besitzt außerordentliches Potenzial – wobei bislang das Problem bestand, diese Zellen kostengünstig und in industriellem Maßstab zu produzieren. Sennewald gelang es im Rahmen ihrer Doktorarbeit an der Technischen Universität Dresden, ein neuartiges Verfahren zu entwickeln und diese komplexen 3D-Strukturen auf handelsüblichen Webmaschinen herzustellen. „Dank des neuen Verfahrens konnte ich Metallfäden und -drähte statt in den üblichen 2D-Strukturen auch zu 3D-Strukturen verbinden, und zwar in ganz unterschiedlichen Größen und Formen“, erläutert Sennewald. „Außerdem gelang es mir – das war ein zweiter großer Schritt nach vorn –, andere Leichtbaustoffe wie Carbon-Fasern mit zu verweben, was ganz neue Einsatzmöglichkeiten eröffnet.“ Die hybride Verbindung von Metallen und Kunststoffen bietet ein weiteres breites Spektrum ableitbarer Anwendungen. „Wir denken an Crash-Elemente, die eine extrem hohe Steifigkeit besitzen und zudem hohe Temperaturen aushalten. Wir könnten auf diese Weise beispielsweise die Betonstrukturen von Gebäuden verstärken, um sie widerstandsfähiger gegen Erdbeben zu machen. Oder sie besser gegen Explosionen schützen. Bei bestehenden Gebäuden könnte hier ein entsprechender Materialauftrag infrage kommen, bei Neubauten könnten die von uns entwickelten zellularen Webstrukturen gleich mit in den Bau einbezogen werden.“

Source:

 Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden