From the Sector

• A paper published in ACS Applied Materials Interfaces details effectiveness, describes protocol for future testing

An international team of scientists and engineers from the University of Cambridge, the Icahn School of Medicine at Mount Sinai, ResInnova Labs and Ascend Performance Materials has found that a nylon fabric embedded with zinc ions successfully inactivated 99% of the viruses that cause COVID-19 and the common flu.

Face masks, protective clothing and filters are used to slow the spread of viruses. But poor-quality masks can harbor active viruses from infected wearers, posing a transmission risk.

“A major challenge is absorption and inactivation,” said Vikram Gopal, Ph.D., co-senior author and chief technology officer at Ascend Performance Materials. “Respiratory viral illnesses, such as COVID-19, and the flu, are transmitted through droplets and aerosols. Polypropylene, the material in commonly used disposable masks, is a hydrophobic plastic and does not absorb moisture. Instead, the viruses can sit on the surface of the mask, posing a transmission risk when the mask is handled.”

Cotton also has problems, Dr. Gopal said. “Cotton effectively absorbs moisture, but it doesn’t inactivate the virus – again, posing a transmission risk,” he said. In the paper published in ACS Applied Materials Interfaces, the researchers described how a fabric made of nylon 6,6 embedded with active zinc ions absorbed virus-containing moisture droplets and effectively inactivated the particles. The fabric produced a 2-log, or 99%, reduction of virus particles in one hour.

The research team also was able to demonstrate that nylon with active zinc ions remains stable over time, keeping its virus-inactivating properties after 50 washes. “The study shows how nylon textile fabric with zinc outperforms the widely used cotton and polypropylene materials at virus absorption and inactivation,” Dr. Gopal said. The findings have significant implications for future development of PPE, Dr. Gopal said. “Pathogen-free PPE does more than just cut down the risk of transmitting the virus,” Gopal said. “By making PPE washable and reusable, you reduce the need for single-use products, keeping hundreds of millions of masks out of landfills.”

• Ramping Up Production of American-Made Polyester Tipped Swabs

The Biden Administration has awarded a contract for $6.5 million to U.S. Cotton LLC, the largest manufacturer of cotton swabs in the United States, to increase domestic production capability for polyester tipped swabs for home testing kits and mass testing applications to fight the COVID-19 pandemic.  Since the beginning of the pandemic, U.S. Cotton has retooled operations to produce over 400 million COVID testing kit swabs.

The Department of Defense (DOD), in coordination with the Department of Health and Human Services (HHS), announced the award today as part of the administration’s broader effort to increase domestic production capability for essential medical supplies.

U.S. Cotton, based in Cleveland, Ohio, said the company will increase its production capacity from 92 million polyester swab tips per month to approximately 371 million polyester swab tips per month by May 2022 to support domestic COVID-19 testing. The DOD contract award was funded through the American Rescue Plan Act (ARPA) to support the domestic industry base expansion for critical medical resources.

John Nims, President of U.S. Cotton said, “We are proud to be involved in a national effort to help deploy these testing kit swabs for the American people. These swabs are designed to make it easier for people at home to self-administer coronavirus tests and will also be used for mass testing applications, which is critically important. We greatly appreciate the collaboration with DOD and HHS to ramp up essential capacity of polyester-based synthetic swabs that will help in the fight against the pandemic.

“We continue to step up to meet our nation’s critical need for American-made coronavirus testing kit swabs on a massive scale. It is an honor to work with our government to help fight this pandemic and use our innovative technologies based here in the United States to fill a national and global demand for testing kits. I especially want to thank Senator Brown and Senator Portman for all their incredible support to help us retool and expand our operations in Cleveland. We can’t thank them enough for their tireless work and also want to recognize their hard working staff. As the Delta variant surges across the country, this timely investment will help in the fight against COVID by adding this much-needed, long-term surge capacity.”

Kim Glas, President and CEO of NCTO, said, “We want to sincerely thank President Biden, the Department of Defense, and the Department of Health and Human Services for leading this critical industrial expansion effort. We appreciate the administration’s commitment to expand the U.S. industrial base for these essential products.  We have a once-in-a-generation opportunity to onshore these critical supply chains long-term and we look forward to working with the administration and Congress to advance long-term solutions.”

In light of recent Covid-19 cases in China, the Autumn Editions of Intertextile Shanghai Apparel Fabrics, Intertextile Shanghai Home Textiles and Yarn Expo will be rescheduled to 9 – 11 October 2021. The fairs were originally due to take place at the end of August at the National Exhibition and Convention Center (Shanghai).

Ms Wendy Wen, Senior General Manager of Messe Frankfurt (HK) Ltd explained: “To comply with the government guidelines for pandemic containment and following discussions with our stakeholders, we have made the decision to postpone the fairs from their original August timing. To allow our exhibitors and buyers as much time as possible to plan ahead, we have already confirmed new dates with the fairground for the three concurrent fairs: 9 – 11 October.”

“I would like to thank the participants of all three fairs for their understanding and ongoing support as we continue to operate in uncertain times. We remain dedicated to providing a quality international trading platform for three sectors for the autumn / winter sourcing season, and our overseas suppliers will still be able to participate through our hybrid exhibition scheme if they are unable to be in Shanghai in-person.”

Exhibitors or visitors with any queries about these fairs should email textile@hongkong.messefrankfurt.com, or visit the fairs’ respective websites:
•    Intertextile Shanghai Apparel Fabrics: https://intertextileapparel.hk.messefrankfurt.com/
•    Intertextile Shanghai Home Textiles: https://intertextilehome.hk.messefrankfurt.com/
•    Yarn Expo: www.yarnexpochina.com

Intertextile Shanghai Apparel Fabrics is co-organised by Messe Frankfurt (HK) Ltd; the Sub-Council of Textile Industry, CCPIT; and the China Textile Information Centre. The co-organisers of Yarn Expo are Messe Frankfurt (HK) Ltd and the Sub-Council of Textile Industry, CCPIT. Intertextile Shanghai Home Textiles is co-organised by Messe Frankfurt (HK) Ltd; the Sub-Council of Textile Industry, CCPIT; and the China Home Textile Association (CHTA).

• Fraunhofer, SABIC, and Procter & Gamble join forces
• The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics.
• The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

Due to COVID-19, use of billions of disposable facemasks is raising environmental concerns especially when they are thoughtlessly discarded in public spaces, including - parks, open-air venues and beaches. Apart from the challenge of dealing with such huge volumes of essential personal healthcare items in a sustainable way, simply throwing the used masks away for disposal on landfill sites or in incineration plants represents a loss of valuable feedstock for new material.

“Recognizing the challenge, we set out to explore how used facemasks could potentially be returned into the value chain of new facemask production”, says Dr. Peter Dziezok, Director R&D Open Innovation at P&G. “But creating a true circular solution from both a sustainable and an economically feasible perspective takes partners. Therefore, we teamed up with Fraunhofer CCPE and Fraunhofer UMSICHT’s expert scientists and SABIC’s Technology & Innovation specialists to investigate potential solutions.”

As part of the pilot, P&G collected used facemasks worn by employees or given to visitors at its manufacturing and research sites in Germany. Although those masks are always disposed of responsibly, there was no ideal route in place to recycle them efficiently. To help demonstrate a potential step change in this scenario, special collection bins were set up, and the collected used masks were sent to Fraunhofer for further processing in a dedicated research pyrolysis plant.

“A single-use medical product such as a face mask has high hygiene requirements, both in terms of disposal and production. Mechanical recycling, would have not done the job”, explains Dr. Alexander Hofmann, Head of Department Recycling Management at Fraunhofer UMSICHT. “In our solution, therefore, the masks were first automatically shredded and then thermochemically converted to pyrolysis oil. Pyrolysis breaks the plastic down into molecular fragments under pressure and heat, which will also destroy any residual pollutants or pathogens, such as the Coronavirus. In this way it is possible to produce feedstock for new plastics in virgin quality that can also meet the requirements for medical products”, adds Hofmann, who is also Head of Research Department “Advanced Recycling” at Fraunhofer CCPE.

The pyrolysis oil was then sent to SABIC to be used as feedstock for the production of new PP resin. The resins were produced using the widely recognized principle of mass balance to combine the alternative feedstock with fossil-based feedstock in the production process. Mass balance is considered a crucial bridge between today’s large scale linear economy and the more sustainable circular economy of the future, which today is operated on a smaller scale but is expected to grow quickly.

“The high-quality circular PP polymer obtained in this pilot clearly demonstrates that closed-loop recycling is achievable through active collaboration of players from across the value chain”, emphasizes Mark Vester, Global Circular Economy Leader at SABIC. “The circular material is part of our TRUCIRCLE™ portfolio, aimed at preventing valuable used plastic from becoming waste and at mitigating the depletion of fossil resources.”

Finally, to close the loop, the PP polymer was supplied to P&G, where it was processed into non-woven fibers material. “This pilot project has helped us to assess if the close loop approach could work for hygienic and medical grade plastics”, says Hansjörg Reick, P&G Senior Director Open Innovation. “Of course, further work is needed but the results so far have been very encouraging.”

The entire closed loop pilot project from facemask collection to production was developed and implemented within seven months. The transferability of advanced recycling to other feedstocks and chemical products is being further researched at Fraunhofer CCPE.

Although affected by the Covid-19 pandemic, ITMA ASIA + CITME, which takes place mid-June in Shanghai, will see a convincing participation of VDMA member companies. 56 exhibitors from Germany will exhibit at this year’s edition of Asia’s major fair for textile machinery. Due to the pandemic and travel restrictions, this is much less than in 2018, when 99 exhibitors from Germany were present. The booked space of German companies has almost halved compared to 2018. Nevertheless, Germany is still the second largest exhibitor nation after China.

At a virtual VDMA press conference early June, these renowned VDMA member companies* presented their highlights for the Asian market:

• Oerlikon Polymer Processing Solutions Division
• Truetzschler Group
• Neuenhauser
• Saurer
• Karl Mayer
• Groz-Beckert
• Herzog
• Lenze
• Mahlo
• Sedo Treepoint
• Thies

Instead of visiting the show personally, the VDMA offers a virtual trip to Asia. The established "Textile Machinery Webtalk" series via the newsroom IndustryArena will focus on ITMA ASIA in the run-up to the fair: VDMA Webtalks meet ITMA ASIA.

*See attached document for more information.

Corona hat die deutsche Schuhbranche schwer getroffen. Das Marktvolumen für Schuhe sank 2020 im Vergleich zum Vorjahr mit minus 9,2 Prozent auf den tiefsten Stand seit 10 Jahren. In Pandemiezeiten mit Lockdown, Homeoffice und Homeschooling kauften die Deutschen weniger bzw. preisorientierter. Nicht alle Schuhsegmente traf es gleichermaßen: Für Modelle für Zuhause sowie solche für die wenigen Freizeitmöglichkeiten wie Running oder Wandern wurden weniger drastische Einbrüche verzeichnet.

Größter Verlierer war der Schuh-Facheinzelhandel, der Corona-bedingt nach der Verkaufssaison Frühjahr/Sommer 2020, auch im Herbst/Winter 2020/21 auf einem großen Teil der eingekauften Ware sitzen blieb. Konkret gab der Marktanteil des Schuh-Facheinzelhandels im Corona-Jahr 2020 gegenüber 2019 mit minus 7,7 Prozentpunkten überproportional nach. Dagegen erwies sich der Online-Handel mit 25 Prozent Umsatzplus als Krisengewinner der Pandemie.

Einblicke in das Kaufverhalten der Deutschen gibt die Kooperationsstudie „Branchen-REPORT Schuhe 2021“ mit der Auswertung von mehr als 1,7 Millionen Online-Bestellungen, die im Zeitraum Januar 2019 bis März 2021 über das Portal Schuhe24.de getätigt wurden. Darin werfen die Marktforscher auch einen Blick in die Schuhzukunft bis 2028. Anhand wissenschaftlicher Methoden werden dabei vier Modelle für die Branche aufgezeigt. Danach winkt der Branche beispielsweise im optimistischen Szenario schon 2022 ein Umsatz, der das Marktvolumen von 2019 sogar übersteigt. Ein Trend, der explizit für Damenschuhe dargestellt wird, während die Perspektiven für Herren- und Kinderschuhe weniger dynamisch ausfallen.

NCTO President and CEO Kim Glas testifies on “COVID-19 Part II: Evaluating the Medical Supply Chain and Pandemic Response Gaps, before the Senate Homeland Security and Governmental Affairs Committee.

In written testimony submitted to the committee, Glas provides an overview of: the U.S. market prior to the pandemic and the root causes of America’s dependence on offshore sources for medical PPE; the heroic response of the U.S. textile industry; the federal government’s response to the crisis; and a series of policy recommendations to incentivize the establishment of a permanent domestic PPE supply chain.

Glas details key policy recommendations designed to establish a permanent domestic PPE supply chain, including:

• Create strong domestic procurement rules for federal PPE purchases and other essential products--substantially similar to the Berry Amendment and the Kissell Amendment which require 100% US content from fiber production forward
• Implement forward-looking policies to shore up the Strategic National Stockpile and issue long-term contracts to incentivize investment in the domestic PPE manufacturing base
• Create federal incentives for private sector hospitals and large provider networks to purchase domestically-produced PPE
• Continue to deploy the Defense Production Act to shore up the textile industrial base from raw materials to end products for all essential products

View the full written testimony here.

National Council of Textile Organizations (NCTO) President and CEO Kim Glas is testifying on “Supply Chain Resiliency and the Role of Small Manufacturers” before the Small Business Committee’s Subcommittee on Economic Growth, Tax, and Capital Access.
 
In written testimony submitted to the committee, Glas provides an overview of the incredible resiliency of the U.S. textile industry during the COVID-19 pandemic, the impact of the ensuing economic crisis, existing options available to small manufacturers to access capital, and policy recommendations to strengthen the entire industry domestic supply chain.

“One silver lining associated with the immense challenges posed by the COVID-19 crisis is that it afforded the domestic textile industry an opportunity to demonstrate its enormous resiliency, flexibility, and overall value to the U.S. economy,” Glas says in the testimony. “Despite the fact that there was virtually no [full] U.S. production of textile-based PPE prior to the pandemic, the heroic actions of domestic textile manufacturers resulted in the ability to supply homegrown PPE at the height of the greatest healthcare emergency our country has faced in the past 100 years.”

“As we exit the current crisis, rational federal policies are once again needed to ensure a stable overall environment where small businesses can compete and thrive, and targeted initiatives are required to ensure that domestic supply chains for critical materials, such as PPE, exist in the United States,” Glas notes.

Glas details five key policy recommendations supported by 20 trade associations and labor groups, representing the entire domestic supply chain aimed at strengthening the integrated U.S. textile sector:

• Strengthen Buy American procurement rules
• Provide funding assistance for companies to reconstitute domestic supply chains important to U.S. national and healthcare security
• Key contracting reforms
• Streamline the SBA loan application process
• Provide additional funding for workforce training

Please view the full written testimony by NCTO President and CEO Kim Glas here.

AMAC cooperates with ITA (Institute for Textile Technology of RWTH Aachen University and their ITA GmbH) for the business development in composites 

As of April 19th, 2021, AMAC is pleased to announce its cooperation with the Institute for Textile Technology, ITA, of RWTH Aachen University and their ITA GmbH. The aim of the cooperation is to strengthen and develop their business activities in composites.

ITA, as one of the largest institutes on the campus of the excellence University RWTH Aachen, Germany, develops complete solutions from the manufacturing of the fiber itself over the processing of textile intermediates with thermoplastic and thermoset resins, textile-based part manufacturing, capabilities such as braiding, pultrusion and in-situ impregnation of textile preforms. Top 3 focused industries are transportation and particularly the e-mobility sector, building and construction as well as the wind energy sector. Additionally, ITA GmbH is the partner of the industry in R&D, focusing on 8 business segments, providing technology and knowledge transfer, as well as offering comprehensive solutions along the entire textile value chain.

Prof. Dr. Thomas Gries, Director of ITA, explains the background of the strategic cooperation with focus on composites: „Our long-term experience and unmatched know-how with all aspects of continuous fibers, non-wovens and web-based reinforcements allows us to deliver to the composite manufacturers a complete technology and service offer around the development of technical textiles, from the development of glass and carbon fibers to the textile-based processing of composite parts. In all process steps of our research and developments, we focus on sustainable and recyclable solutions, an efficient cost-performance ratio, the possible use of bio-based materials and the reduction of the CO2 footprint. We are glad to cooperate with Dr. Michael Effing and AMAC in order to benefit from his door-opening network in the composites industry. “

Dr. Michael Effing, Managing Director of AMAC GmbH: „I am very happy to support the ITA to generate innovation thanks to further industrial networking and pre-competitive joint projects. ITA is indeed a one-stop source for composite solutions from the fiber to the cost-efficient manufacturing of final parts. In the context of the Covid-19 impact to the entire industry, it makes sense to bundle forces. Furthermore, ITA, with its long tradition and satisfied customers offers further valuable networking opportunities to the composites industry as well as access to relevant complementary fiber-based excellence and 250 different technologies in their machine-park with an outstanding infrastructure in Aachen.”

After a turbulent year, it seems strange to be thinking about ‘after the pandemic’, but with millions of vaccinations underway, the light at the end of the tunnel is visible. As we turn the corner, choosing technology partners that understand how to proactively respond to changing market needs and support the evolving requirements of print businesses and end customers will be vital. The printers in Mimaki’s ‘100 series’ portfolio, which consists of the high quality, high productivity entry level roll-to-roll inkjet printers the UJV100-160 UV and the JV100-160 solvent, and the high performance textile printer, the TS100-1600, are a perfect reflection of the way technology requirements are adapting in line with the industry as we look to the future. To demonstrate this, we have identified three post-pandemic technology touchpoints that will help print businesses target success amid uncertainty.

• Productivity

The pandemic has served as a major catalyst for existing trends, and our growing appetite for everything on-demand has been given a huge COVID-related boost. For printers, a digital solution that offers premium productivity, quality and efficiency at an entry-level price point is sure to be an invaluable investment to meet evolving ‘on-demand demands’. Adding a digital production element to your business doesn’t need to be daunting, complicated or overpriced – the Mimaki ‘100 series’ truly lives up to the tagline ‘Expert Printing Made Easy’, offering an incredibly intuitive user experience for streamlined, ultra-efficient printing, high-quality output, and cost-effective implementation. The powerful and productive new textile printer in the ‘100 series’, the TS100-1600, is a shining example of equipment developed with the future of the market in mind – the textile industry is fast-paced and constantly innovating, and the printer you invest in needs to keep up with your creativity.

• Diversity

2021 is set to be a period of transition. While that will mean navigating uncertainty, the ‘glass half full’ approach is to view the year ahead in terms of opportunities such as expanding your business, exploring alternative revenue streams, and taking the plunge into new markets. In the past, it may have felt as if the barriers to entry when it came to looking beyond your core business were too great. However, in a post-pandemic world, we need to break some of those barriers down and demonstrate that success with digital print is within reach if you invest in the right equipment. With the ‘100 series’ portfolio, Mimaki is acknowledging what print service providers need from their technology partners – the UJV100-160 and the JV100-160 are suitable for a wide range of applications that will allow you to easily and affordably diversify your offering, and with the TS100-1600 textile printer, it has never been easier to target growth in the thriving textile sector, even in challenging times.

• Affordability

Affordability is one of the most significant barriers to entry into new markets. 2020 was a year of unprecedented economic challenges, so it’s more important than ever to be thinking about gaining a competitive edge, and the printers in the ‘100 series’ from Mimaki have been specifically formulated to help you ramp up productivity while keeping running costs low. Whether you want to take your first foray into digital print production, expand the services you offer or simply grow your customer base, cost can be a major sticking point, which is why supporting customers is Mimaki’s number one priority, designing the ‘100 series’ around your needs and continuing to listen to how those needs are developing. Making an investment in the JV100-160 in order to move into outdoor graphics; meeting demand for faster turnaround times by adding the instantly curable UJV100-160 to your production setup; or taking a leap into new revenue streams with the TS100-160 – it’s all ‘100’ percent accessible.