From the Sector

Reset
2 results
03.09.2018

New ENGEL Injection Molding System at AZL of RWTH Aachen University

The Aachen Center for Integrative Lightweight Production (AZL) of RWTH Aachen University is installing a new ENGEL injection molding system in its technical center. Engel Deutschland GmbH – in cooperation with the ENGEL Centre for Lightweight Composite Technologies in Austria – will install the 2-component injection molding system with turning plate and 17,000 kN clamping force in 2019. This machine setup is the basis for further developments of efficient inline-combination technologies using different kinds of polymer performance materials.

The ENGEL injection molding system will enable innovative combinations of already established fiber-reinforced plastics (FRP) processes and the development of new individual processes. The focus is on increasing resource efficiency in lightweight production. With the new equipment, new research and development initiatives can explore the more efficient use of materials, which are eventually the key to the mass production of lightweight components. The research will address multi-material systems, continuous processes, process chains as well as self-optimizing processes.

The Aachen Center for Integrative Lightweight Production (AZL) of RWTH Aachen University is installing a new ENGEL injection molding system in its technical center. Engel Deutschland GmbH – in cooperation with the ENGEL Centre for Lightweight Composite Technologies in Austria – will install the 2-component injection molding system with turning plate and 17,000 kN clamping force in 2019. This machine setup is the basis for further developments of efficient inline-combination technologies using different kinds of polymer performance materials.

The ENGEL injection molding system will enable innovative combinations of already established fiber-reinforced plastics (FRP) processes and the development of new individual processes. The focus is on increasing resource efficiency in lightweight production. With the new equipment, new research and development initiatives can explore the more efficient use of materials, which are eventually the key to the mass production of lightweight components. The research will address multi-material systems, continuous processes, process chains as well as self-optimizing processes.

Dr.-Ing. Michael Emonts, Managing Director of the Aachen Center for Integrative Lightweight Production (AZL) is looking forward to realizing new innovative lightweight production process with the new injection molding system: “This new injection molding system offers us as specialists for lightweight production technology in cooperation with the injection molding experts of the Institute of Plastics Processing – the IKV – the opportunity to establish hybrid processes for industrial lightweight applications. The system will expand our existing machinery in the AZL Technical Center and will be available as an important platform for lightweight production research at RWTH Aachen University.”

Being a Partner of the AZL, ENGEL has already been working closely with the AZL for many years as a Partner Company of the AZL Partner Network. Dr. Stefan Engleder, CEO of the ENGEL Group, emphasizes the importance of close collaboration with technical universities and especially with the AZL: “The AZL provides great conditions for industry-related research activities in the field of lightweight composites as it is characterized by a strong interdisciplinary approach. It benefits from the great infrastructure and the collaboration with well-known institutes of the RTWH Aachen University. ENGEL is looking forward to working together with the AZL on developing efficient lightweight composite mass production processes.”

In addition to the numerous composite and lightweight equipment at the RWTH Aachen Campus, the AZL Technical Center comprises large-scale equipment for the development of processes for lightweight production, such as a composite press from Schuler Pressen GmbH with 18,000 kN clamping force.

 

(c) ENGEL AUSTRIA GmbH: (l. to r.) Dr. Norbert Müller (Leiter des ENGEL Technologiezentrums für Leichtbau-Composites), Dr. Michael Emonts (Geschäftsführer des Aachener Zentrums für integrativen Leichtbau (AZL) der RWTH Aachen), Rolf Saß (Geschäftsführer der ENGEL Deutschland GmbH) und Dr. Christoph Steger (Geschäftsführer Vertrieb der ENGEL Holding).
03.09.2018

ENGEL installiert neues Spritzgießsystem im AZL der RWTH Aachen

Das Aachener Zentrum für Integrative Leichtbau (AZL) der RWTH Aachen installiert in seinem Technikum eine neue ENGEL-Spritzgießanlage. Die ENGEL Deutschland GmbH, in Kooperation mit dem ENGEL Technologiezentrum für Leichtbau-Composites in Österreich, wird das 2-Komponenten-Spritzgieß-System mit Drehtisch und 17.000 kN Schließkraft im Jahr 2019 in Betrieb nehmen. Dieser Maschinenaufbau ist die Basis für die Weiterentwicklung effizienter Inline-Kombinations-Technologien mit unterschiedlichen Polymerwerkstoffen.

Das ENGEL-Spritzgießsystem ermöglicht die innovative Kombination bereits etablierter Faserverbundkunststoff-Verfahren und die Entwicklung neuer individueller Verfahren. Im Mittelpunkt steht die Steigerung der Ressourceneffizienz in der Leichtbau-Produktion. Mit der neuen Anlage können neue Forschungs- und Entwicklungsinitiativen einen effizienteren Materialeinsatz adressieren, der letztlich der Schlüssel zur Massenproduktion von Leichtbauteilen ist. Der Fokus wird dabei auf Multimaterialsystemen, kontinuierlichen Prozessen und Prozessketten sowie selbstoptimierenden Prozesse liegen.

Das Aachener Zentrum für Integrative Leichtbau (AZL) der RWTH Aachen installiert in seinem Technikum eine neue ENGEL-Spritzgießanlage. Die ENGEL Deutschland GmbH, in Kooperation mit dem ENGEL Technologiezentrum für Leichtbau-Composites in Österreich, wird das 2-Komponenten-Spritzgieß-System mit Drehtisch und 17.000 kN Schließkraft im Jahr 2019 in Betrieb nehmen. Dieser Maschinenaufbau ist die Basis für die Weiterentwicklung effizienter Inline-Kombinations-Technologien mit unterschiedlichen Polymerwerkstoffen.

Das ENGEL-Spritzgießsystem ermöglicht die innovative Kombination bereits etablierter Faserverbundkunststoff-Verfahren und die Entwicklung neuer individueller Verfahren. Im Mittelpunkt steht die Steigerung der Ressourceneffizienz in der Leichtbau-Produktion. Mit der neuen Anlage können neue Forschungs- und Entwicklungsinitiativen einen effizienteren Materialeinsatz adressieren, der letztlich der Schlüssel zur Massenproduktion von Leichtbauteilen ist. Der Fokus wird dabei auf Multimaterialsystemen, kontinuierlichen Prozessen und Prozessketten sowie selbstoptimierenden Prozesse liegen.

Dr.-Ing. Michael Emonts, Geschäftsführer des Aachener Zentrums für integrativen Leichtbau (AZL) freut sich darauf, mit dem neuen Spritzgießsystem neue innovative Leichtbauverfahren zu realisieren: „Diese neue Spritzgießanlage bietet uns als Spezialisten für die Leichtbau-Produktionstechnik in Kooperation mit den Spritzgießexperten des Instituts für Kunststoffverarbeitung – dem IKV – die Möglichkeit, Hybridverfahren für industrielle Leichtbau-Anwendungen zu etablieren. Das System wird unseren bestehenden Maschinenpark im AZL-Technikum erweitern und als wichtige Plattform für die Leichtbau-Forschung an der RWTH zur Verfügung stehen."

Als aktive Partnerfirma des AZL-Partnernetzwerks arbeitet ENGEL bereits seit vielen Jahren eng mit dem AZL zusammen. Dr. Stefan Engleder, CEO der ENGEL-Gruppe, betont die Bedeutung dieser engen Zusammenarbeit mit den Technischen Universitäten und insbesondere mit dem AZL: „Das AZL bietet beste Voraussetzungen für industrienahe Forschungsaktivitäten im Bereich Leichtbau-Verbundwerkstoffe, da es sich durch einen starken interdisziplinären Ansatz auszeichnet. Das AZL profitiert von der guten Infrastruktur und der Zusammenarbeit mit namhaften Instituten der RTWH Aachen. ENGEL freut sich auf die Zusammenarbeit mit dem AZL bei der Entwicklung effizienter Leichtbau-Verbundwerkstoff-Massenproduktionsverfahren.“

Das AZL-Technikum umfasst neben den zahlreichen Faserverbund- und Leichtbauanlagen auf dem Campus der RWTH Aachen zusätzliches Großserien-Equipment für die Entwicklung von Verfahren zur Leichtbau-Produktion, wie zum Beispiel eine Composite-Presse der Schuler Pressen GmbH mit 18.000 kN Schließkraft.

More information:
AZL
Source:

AZL Aachen GmbH