From the Sector

Reset
18 results
Baldwin presents spray finishing system at Techtexil (c) Baldwin Technology Company Inc.
13.03.2024

Baldwin presents spray finishing system at Techtexil

Baldwin Technology Co. will join Elmatex GmbH at Techtexil (April 23-26 in Frankfurt, Germany) to demonstrate its TexCoat™ G4 precision spray finishing system.

Baldwin Technology Co. will join Elmatex GmbH at Techtexil (April 23-26 in Frankfurt, Germany) to demonstrate its TexCoat™ G4 precision spray finishing system.

With Baldwin’s system, the chemistry is precisely distributed across the textile surface and is applied only where it is required, on one or both sides of the fabric. The non-contact technology eliminates chemistry dilution in wet-on-wet processes, allowing full control of maintaining consistent chemistry coverage rates. Plus, pad bath contamination is eliminated, and changeovers are only required when there is a change of finish chemistry.
 
Furthermore, the system offers automated speed tracking, fabric-width compensation, and real-time monitoring to track system uptime, performance and chemistry usage, as well as active care alerts.
 
In addition, the TexCoat™ G4 system can process a wide range of low-viscosity water-based chemicals, such as durable water repellents, softeners, antimicrobials, flame retardants and more. Baldwin’s technology utilizes the same chemicals used in the traditional pad bath, and no special auxiliaries are required. The recipe is adjusted by increasing the concentration and reducing the pickup by a corresponding amount, so that the same level of solids is applied.
 
Some applications, such as durable water repellents, are only applied on the face of the fabric, instead of the traditional method of saturation through dipping and squeezing. Drier fabric entering the stenter means lower drying temperatures and faster process speeds. Single-side applications also open up the opportunity to process back-coated or laminated fabrics in a single pass of the stenter, instead of two passes.

Baldwin at ITMA Asia 2023 with Precision Spray TexCoat™ System (c) Baldwin Technology Company Inc.
06.11.2023

Baldwin at ITMA Asia 2023 with Precision Spray TexCoat™ System

Baldwin Technology Company Inc. will showcase its TexCoat™ G4 precision spray finishing system at ITMA Asia 2023 (November 19-23, National Exhibition and Convention Center, Shanghai). ITMA Asia participants can stop by and see Baldwin’s wide array of TexCoat G4-applied fabric samples from textile mills around the world and experience what precision finishing feels like while learning how the technology eliminates chemistry waste on changeover, saves water, and achieves faster speeds through the stenter frame and relaxed dryer.
 
Baldwin’s team will be available to discuss how the company’s technology can meet the textile supply chain’s sustainability and carbon footprint goals while improving performance and saving money. In the context of a cost-sensitive global economy and an increased focus by brands, consumers and regulatory agencies on sustainability, customers are placing a premium on sustainability-advantage textile production.

Baldwin Technology Company Inc. will showcase its TexCoat™ G4 precision spray finishing system at ITMA Asia 2023 (November 19-23, National Exhibition and Convention Center, Shanghai). ITMA Asia participants can stop by and see Baldwin’s wide array of TexCoat G4-applied fabric samples from textile mills around the world and experience what precision finishing feels like while learning how the technology eliminates chemistry waste on changeover, saves water, and achieves faster speeds through the stenter frame and relaxed dryer.
 
Baldwin’s team will be available to discuss how the company’s technology can meet the textile supply chain’s sustainability and carbon footprint goals while improving performance and saving money. In the context of a cost-sensitive global economy and an increased focus by brands, consumers and regulatory agencies on sustainability, customers are placing a premium on sustainability-advantage textile production.

TexCoat G4’s non-contact spray technology offers numerous advantages compared to outdated finishing-chemistry application methods. TexCoat G4 processes a wide range of low-viscosity water-based chemicals, such as durable water-repellents –  including PFAS-free, softeners, anti-microbials, easy-care and flame retardants. The company's technology uses the same chemicals as found in traditional pad baths with no special auxiliaries required.

Testimonial videos from Pincroft Dyeing and Print Works and Graniteville Specialty Fabrics along with a video highlighting Baldwin’s partnership with North Carolina State University will also be screened at their stand.

Source:

Baldwin Technology Company Inc.

14.09.2023

Rudolf commissions Baldwin’s TexCoat™ G4 lab-scale precision spray unit

Rudolf GmbH, a provider of chemicals to the textile industry, can now offer side-by-side performance tests of the age-old “dip and squeeze” pad versus precision spray finishing with the delivery of Baldwin Technology Inc.’s TexCoat ™ G4 lab-scale unit.

Rudolf GmbH, a provider of chemicals to the textile industry, can now offer side-by-side performance tests of the age-old “dip and squeeze” pad versus precision spray finishing with the delivery of Baldwin Technology Inc.’s TexCoat ™ G4 lab-scale unit.

The new TexCoat lab-scale unit at Rudolf’s Geretsried, Germany-based Customer Solution Center, tests the sprayability of chemicals on fabrics as an additional tool to help the market transition to precision spray with confidence in the performance and sustainability of the end result.
 
With Baldwin’s innovative system, the chemistry is precisely distributed across the textile surface and is applied only where it is required, on one or both sides of the fabric. The non-contact technology eliminates chemistry dilution in wet-on-wet processes, allowing full control of maintaining consistent chemistry coverage rates.
 
Plus, pad bath contamination is eliminated, and changeovers are only required when there is a change of finish chemistry. On wet-on-dry processes, the finish is applied with 50% of the amount of water required for pad finishing. Dryer fabric entering the stenter means less water to evaporate resulting in less energy and higher production speeds.
 
More specifically, with Baldwin’s TexCoat G4, textile finishers can track and control the finishing process. Changeovers are quickly performed thanks to recipe management, including automated chemistry and coverage selection. Furthermore, the system takes speed information from the drying process to insure exact coverage regardless of any change in speed. TexCoat G4 measures every drop of chemical usage ensuring that the amount of chemical add-on is precise.
 
In addition, the TexCoat G4 system can process a wide range of low-viscosity water-based chemicals, such as durable water-repellants including PFAS-free, softeners, anti-microbials, easy care resins, flame retardants and more. Baldwin’s technology utilizes the same chemicals used in the traditional pad bath, with no special auxiliaries required.

Source:

Baldwin Technology Company Inc.

Photo: AVK
26.05.2023

AVK: Successful Flame Retardancy Conference in Berlin

  • Flame Retardancy for Composites Applications in the Transport Sector

On 10-11 May 2023, the AVK - Industrievereinigung Verstärkte Kunststoffe e. V. in cooperation with the FGK - Forschungsgesellschaft Kunststoffe e.V. in Berlin organised for the first time an international, English-language conference on flame retardancy.

In 18 compact lectures, more than 20 experts informed nearly 80 participants about new developments, requirements and innovations regarding specific flame retardant properties of components made of fibre-reinforced plastics/composites for the transport sector.

Among others, there were presentations by industry representatives from Saertex, BÜFA, Clariant, Diehl Aviation and Airbus, but also from institutes such as the Fraunhofer Institutes or the Federal Institute for Materials Research and Testing. Presentations on the topics of standardisation, raw materials, automotive or recycling were on the agenda, but also flame retardants for connectors and battery housings for electric vehicles or fire-retardant systems for rail vehicles or fire-retardant CFRP made from recycled CF nonwoven were presented.

  • Flame Retardancy for Composites Applications in the Transport Sector

On 10-11 May 2023, the AVK - Industrievereinigung Verstärkte Kunststoffe e. V. in cooperation with the FGK - Forschungsgesellschaft Kunststoffe e.V. in Berlin organised for the first time an international, English-language conference on flame retardancy.

In 18 compact lectures, more than 20 experts informed nearly 80 participants about new developments, requirements and innovations regarding specific flame retardant properties of components made of fibre-reinforced plastics/composites for the transport sector.

Among others, there were presentations by industry representatives from Saertex, BÜFA, Clariant, Diehl Aviation and Airbus, but also from institutes such as the Fraunhofer Institutes or the Federal Institute for Materials Research and Testing. Presentations on the topics of standardisation, raw materials, automotive or recycling were on the agenda, but also flame retardants for connectors and battery housings for electric vehicles or fire-retardant systems for rail vehicles or fire-retardant CFRP made from recycled CF nonwoven were presented.

More information:
AVK Composites flame retardant
Source:

AVK

31.10.2022

Cinte Techtextil China announces exhibitors for December Edition

From 7 – 9 December 2022, Cinte Techtextil China will welcome visitors sourcing solutions for 12 application areas of technical textiles and nonwovens at the National Exhibition and Convention Center in Shanghai.

A number of countries and regions are represented at the fair’s International Zone, with companies from Austria, Belgium, France, Germany, Hong Kong, Italy, the Netherlands, Spain, Sweden, Switzerland, Taiwan, and the US. Standout international exhibitors include:

From 7 – 9 December 2022, Cinte Techtextil China will welcome visitors sourcing solutions for 12 application areas of technical textiles and nonwovens at the National Exhibition and Convention Center in Shanghai.

A number of countries and regions are represented at the fair’s International Zone, with companies from Austria, Belgium, France, Germany, Hong Kong, Italy, the Netherlands, Spain, Sweden, Switzerland, Taiwan, and the US. Standout international exhibitors include:

  • TESTEX, an international, independent Swiss institute which specialises in the testing and certification of textile and leather products. The organisation is a founding member and official representative of the OEKO-TEX® Association, and will present their certification services at the fairground.
  • Cotton Council International (CCI) is a non-profit trade association that promotes US cotton fibre and manufactured cotton products, with their COTTON USA™ Mark. At this year’s fair they will showcase cotton spunlace fabric, wipes, kitchen tissues, facial masks, cosmetic removers, and more, with their products particularly applicable to Agrotech, Clothtech, Medtech, and Sporttech.
  • Graf + Cie AG is a subsidiary of the Rieter Group, and a leading supplier of clothing for carding and combs for combing machines in the short- and long-staple spinning industry. This year, the Swiss company will showcase stationary flats, and metallic card clothing for roller cards.
  • At the returning German Pavilion, buyers can source sought-after technical textiles and nonwovens that are renowned for their quality. The companies and expertise on display at this pavilion are endorsed by the Federal Republic of Germany, with several exhibitors highlighted below:
  • Brückner Textile Technologies GmbH & Co KG has developed machinery for the textile industry since 1949. Today, the company offers complete line systems for the dry finishing of both woven and knitted fabric, as well as for technical textiles, glass fibres, and floor coverings.
  • Perlon (Zhejiang) Co Ltd is part of a global group of companies that specialises in the manufacture of synthetic filaments, with factories in China, Germany, Poland, and the US. Their products have a diverse range of potential uses, largely categorised in the Agrotech and Indutech application areas.
  • IBENA Textilwerke GmbH produces various functional fabrics for Protech. At the fair, the company will be showcasing insulative, flame retardant (FR) textiles for firefighting and search & rescue services. Developed with DuPont™ aramid material, their FR properties will not diminish after washing or repeated use.

This year’s fair also sees the return of the Taiwan Zone. With support from the Taiwan Nonwoven Fabrics Industry Association, the area will showcase a range of industry leading nonwoven products and services, by brands such as KNH Enterprise, Nan Liu Enterprise, Unique Pretty Ind, and Web-Pro Corporation.

As a world’s largest manufacturer of technical textiles, China is home to a vast array of companies responsible for innovative products. Some domestic exhibitors to look out for are:

  • CTA Hi-Textiles Co Ltd, a high-tech enterprise controlled by China Textile Science Research Institute. In recent years, the company has developed several new textile composite materials, and their products are widely used in sectors such as national defence, policing and public security, medical protection, and engineering and manufacturing.
  • Sateri is one of the world’s largest producers of viscose fibre, with an annual capacity of 1.8 million metric tonnes. At their mills, they make yarn and fibre products applicable to sectors such as beauty, hygiene and personal care, medical, wipes, and protective wear.

To help international buyers stay connected with the Chinese market, Match Plus, the fair’s online business matching platform, will support foreign buyers achieve their sourcing goals despite travel limitations. Further information on Match Plus will be available at a later stage.

The fair’s product categories cover 12 application areas, which comprehensively span a full range of potential uses in modern technical textiles and nonwovens. These categories also cover the entire industry, from upstream technology and raw materials providers to finished fabrics, chemicals and other solutions.

05.05.2022

Monforts at Techtextil showcasing its finishing and coating technologies

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

Energy prices are rising steeply everywhere and a particular emphasis for Monforts in Frankfurt will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as better insulation of the treatment chambers or the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air resulting in a radical reduction in the conventional heat supply required compared to gas and thermal oil heating. The modular system for heat recovery can also be extended for exhaust air cleaning and odour elimination. Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation including modification of the heating source.

With the Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

All of these very different materials require coating and finishing for maximum efficiency, using Monforts technologies which provide the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

The Monforts EcoApplicator offers further potential for sustainably achieving perfect finishes via a precise direct application system, as an alternative to conventional padding – where fabrics are immersed in a bath of the required finishing chemicals. It can significantly further reduce the energy and water required and finishes can be applied on just one side of the fabric, or both, and even separately on each side, to be sealed in place via different heating zones in the stenter.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

13.10.2021

Sales partnership for Switzerland starts at Fakuma 2021

  • Polynova to gain market share for the GRAFE Group in the Swiss region from November The GRAFE Group, Blankenhain, has found a new sales representative for Switzerland in Polynova Group AG, Risch-Rotkreuz (Switzerland).

The partnership will be officially launched at Fakuma 2021. "Our new Swiss agency specialises in the distribution and production of high-quality technical plastic granulates and has been active on the market for more than 20 years. The company has a large customer base and the necessary technical expertise to advance our goals in this important market. This includes raising our profile, educating people about our product range and ultimately gaining market share," says Stefanie Theuerkauf, Sales Manager for the D-A-CH region. Polynova employs five sales staff and three in logistics, all of whom have a technical background. The company's own warehouse in Rothenburg also ensures the availability of the plastics.

  • Polynova to gain market share for the GRAFE Group in the Swiss region from November The GRAFE Group, Blankenhain, has found a new sales representative for Switzerland in Polynova Group AG, Risch-Rotkreuz (Switzerland).

The partnership will be officially launched at Fakuma 2021. "Our new Swiss agency specialises in the distribution and production of high-quality technical plastic granulates and has been active on the market for more than 20 years. The company has a large customer base and the necessary technical expertise to advance our goals in this important market. This includes raising our profile, educating people about our product range and ultimately gaining market share," says Stefanie Theuerkauf, Sales Manager for the D-A-CH region. Polynova employs five sales staff and three in logistics, all of whom have a technical background. The company's own warehouse in Rothenburg also ensures the availability of the plastics.

"GRAFE fits perfectly into our product portfolio," says Thomas Weigl, co-owner and responsible for business development at the Swiss distribution company, whose employees recently underwent intensive training in Blankenhain. "Our customers come from the sports goods, housing technology, automotive supplier and medical technology sectors - there are many synergies with GRAFE." Weigl himself has extensive experience in the masterbatch sector and has worked for two companies in the industry - Sukano and Americhem - as managing director. "Swiss companies want Swiss contact persons. We speak the languages German, Italian and French, are on site in the shortest possible time, offer direct contact and understand the needs of the customers and the requirements of the market," he explains. "Polynova is thus faster, closer and more direct." "The Swiss market is large and important for us," reports Theuerkauf and Weigl explains the background: "There are over 300 plastics processors, many are family-run and very technically oriented. The origins of the companies are often in the watch industry and in the production of the smallest precision parts such as gear wheels. In addition, coffee machine manufacturers, medical technology providers and automotive suppliers are important market players. A large number of well-known OEMs are located here."

Even though there are already masterbatch manufacturers in the Alpine country, says the sales expert, no one has the know-how to adjust compounds and masterbatches as perfectly and precisely as the company from Thuringia. In addition to a complete range of colours on practically all plastic substrates, flame retardants, UV additives, thermal stabilisers or lubricants are further examples of the extensive product portfolio. GRAFE is one of the specialists in the modification of thermoplastics and is an innovation driver in the production of colour masterbatches. "The technical possibilities in terms of a state-of-the-art technical centre and production machinery, as well as one of the largest research and development departments in the industry, are also not to be found elsewhere on the Swiss market. Our task now is to bring these to the attention of domestic customers," says Thomas Weigl, co-owner of Polynova AG together with founder Renato R. Huebscher.

Source:

GRAFE Advanced Polymers GmbH

08.07.2021

ECHA: Candidate List updated with eight hazardous chemicals

Some of the newly added substances are used in consumer products such as cosmetics, scented articles, rubber and textiles. Others are used as solvents, flame retardants or to manufacture plastics products. Most have been added to the Candidate List because they are hazardous to human health as they are toxic for reproduction, carcinogenic, respiratory sensitisers or endocrine disruptors.

Companies must follow their legal obligations and ensure the safe use of these chemicals. They also have to notify ECHA under the Waste Framework Directive if their products contain substances of very high concern. This notification is submitted to ECHA’s SCIP database and the information will later be published on the Agency’s website.

Some of the newly added substances are used in consumer products such as cosmetics, scented articles, rubber and textiles. Others are used as solvents, flame retardants or to manufacture plastics products. Most have been added to the Candidate List because they are hazardous to human health as they are toxic for reproduction, carcinogenic, respiratory sensitisers or endocrine disruptors.

Companies must follow their legal obligations and ensure the safe use of these chemicals. They also have to notify ECHA under the Waste Framework Directive if their products contain substances of very high concern. This notification is submitted to ECHA’s SCIP database and the information will later be published on the Agency’s website.

Background
The Candidate List includes substances of very high concern that may have serious effects on our health or the environment. These substances may be placed on the Authorisation List in the future, which means that companies would need to apply for permission to continue using them. The Candidate List has now 219 entries – some of these cover groups of chemicals so the overall number of impacted chemicals is higher.
 
Under the REACH Regulation, companies may have legal obligations when their substance is included – either on its own, in mixtures or in articles – in the Candidate List. Any supplier of articles containing a Candidate List substance above a concentration of 0.1 % weight by weight has to give sufficient information to their customers and consumers to allow safe use.
 
Importers and producers of articles containing a Candidate List substance have six months from the date of its inclusion in the list (8 July 2021) to notify ECHA. Suppliers of substances on the Candidate List (supplied either on their own or in mixtures) have to provide their customers with a safety data sheet.
 
As of 5 January 2021, suppliers of articles on the EU market containing Candidate List substances in a concentration above 0.1% weight by weight must notify these articles to ECHA’s SCIP database. This duty comes from the Waste Framework Directive.
 
More information on these obligations and related tools are available here.

Source:

European Chemicals Agency

(c) Teijin Carbon Europe GmbH
19.05.2021

Teijin Carbon produces new thermoplastic PPS-Tape

Teijin Carbon Europe introduces a new thermoplastic carbon fiber tape (TPUD) based on PPS. The new Tenax™ TPUD with PPS matrix allows entry in new cost-sensitive markets while offering the typical TPUD advantages like high resistance to chemicals and solvents, low flammability, storage or shipping at room temperature and recyclability.  

Due to its flame retardant properties and low smoke emission, it can be used in interior applications of aircraft or rail vehicles, among others. The maximum continuous operating temperature is up to 220 °C. Very low water absorption, excellent creep resistance even at elevated temperatures and high dimensional stability round off the property portfolio of this new TPUD. It is therefore also suitable for demanding applications in the aerospace, oil & gas, sporting goods or industrial sectors, while remaining cost-effective. These properties make the product perfect for highly automated processing routes such as ATL or AFP in combination with overmolding for complex geometries. Production start for the Tenax™ TPUD with PPS matrix is the first quarter in 2021.

Teijin Carbon Europe introduces a new thermoplastic carbon fiber tape (TPUD) based on PPS. The new Tenax™ TPUD with PPS matrix allows entry in new cost-sensitive markets while offering the typical TPUD advantages like high resistance to chemicals and solvents, low flammability, storage or shipping at room temperature and recyclability.  

Due to its flame retardant properties and low smoke emission, it can be used in interior applications of aircraft or rail vehicles, among others. The maximum continuous operating temperature is up to 220 °C. Very low water absorption, excellent creep resistance even at elevated temperatures and high dimensional stability round off the property portfolio of this new TPUD. It is therefore also suitable for demanding applications in the aerospace, oil & gas, sporting goods or industrial sectors, while remaining cost-effective. These properties make the product perfect for highly automated processing routes such as ATL or AFP in combination with overmolding for complex geometries. Production start for the Tenax™ TPUD with PPS matrix is the first quarter in 2021.

For almost 10 years, unidirectional tapes (TPUD) have been manufactured from carbon fibers and thermoplastics in Heinsberg, Germany. The semi-finished products have so far been offered with PEEK or PAEK – and PPS is now added to the list of available matrixes. PPS allows a lower process temperature compared to PEEK or PAEK. For the industrial market in particular, increasing the production rate to make processes more cost-efficient is an opportunity.

Source:

Teijin Carbon Europe GmbH

Elasticated melange tape by JUMBO-Textil for exacting requirements (c) JUMBO-Textil
JUMBO Textil Band schwarz
10.03.2021

JUMBO: The perfect melange

  • Elasticated melange tape by JUMBO-Textil for exacting requirements

Reliable functionality, select aesthetics, exceptional comfort – the new elasticated melange tape from JUMBO-Textil can really do a lot – and looks extremely good doing it.

Great functionality and an elegant design
To create this innovative elasticated tape, different premium-quality yarns are woven into a high-performance tape for especially exacting demands in terms of comfort and visual appeal. The elasticated material offers amazing performance and robustness beyond its elegant, shimmering melange look and its pleasant, fabric-like feel.

•    Ideal for all applications on visible textile surfaces
•    Premium fabric-like aesthetic and feel
•    Shimmering melange effect
•    Can be manufactured in many individual types and fabrications
•    Additional designs possible: water repellent, flame retardant, etc.
•    For applications in vehicle interiors, functional clothing, the furniture industry, medical technology, and much more

  • Elasticated melange tape by JUMBO-Textil for exacting requirements

Reliable functionality, select aesthetics, exceptional comfort – the new elasticated melange tape from JUMBO-Textil can really do a lot – and looks extremely good doing it.

Great functionality and an elegant design
To create this innovative elasticated tape, different premium-quality yarns are woven into a high-performance tape for especially exacting demands in terms of comfort and visual appeal. The elasticated material offers amazing performance and robustness beyond its elegant, shimmering melange look and its pleasant, fabric-like feel.

•    Ideal for all applications on visible textile surfaces
•    Premium fabric-like aesthetic and feel
•    Shimmering melange effect
•    Can be manufactured in many individual types and fabrications
•    Additional designs possible: water repellent, flame retardant, etc.
•    For applications in vehicle interiors, functional clothing, the furniture industry, medical technology, and much more

Wide range of applications in numerous industries
The new melange tape is specially designed and made for all visible applications: from multimedia holding tapes or document retainers in vehicle interiors to the functional and attractive cuff on sleeves, trousers or braces of outdoor or work clothing through to tensioning straps on backpacks, in exoskeletons or upholstered furniture.

"Elasticated tapes are often developed and considered primarily from a functional point of view. In our case it is different: our new melange tape combines great functionality with an elegant design and shows that elasticated narrow textiles can also be aesthetic highlights," as Patrick Kielholz, Business Development Manager at JUMBO-Textil emphasises. "The potential applications for our melange tape are almost limitless. Exciting solutions are available for almost all industries."

The most important properties at a glance:

Colours: grey melange, black melange; optionally, various other colour options
Sample: single-colour melange; optionally, longitudinal stripes, melange
Width, Standard: 40.0 mm
Width, Customized: 10 mm – 320 mm
Elasticity: up to 60%

Source:

JUMBO-Textil GmbH & Co. KG

BIONIC-FINISH®ECO Fluorine-Free, Water Repellent Finishes for Ultimate Performance (c) RUDOLF GmbH
BIONIC-FINISH®ECO Fluorine-Free, Water Repellent Finishes for Ultimate Performance
03.03.2021

BIONIC-FINISH®ECO by RUDOLF GROUP

  • BIONIC-FINISH®ECO Fluorine-Free, Water Repellent Finishes for Ultimate Performance

In recent years, many scientists have shifted from favoring a “primordial soup” in pools of water to hydrothermal vents deep in the ocean as the original source of life on Earth. Regardless what the real beginning really was, water was certainly involved in the process some 3,5bln years ago. And since then, Mother Nature designed many ways to benefit of water and to be sheltered from it. Many engineering challenges humans face can be solved by turning to those 3,5bln years of experience and by using natural design as springboard. That’s biologically inspired engineering or, in short, bionics. BIONIC-FINISH®ECO of RUDOLF GROUP is Mother Nature’s work reproduced on textiles and apparel to protect us from water. To perform.

  • BIONIC-FINISH®ECO Fluorine-Free, Water Repellent Finishes for Ultimate Performance

In recent years, many scientists have shifted from favoring a “primordial soup” in pools of water to hydrothermal vents deep in the ocean as the original source of life on Earth. Regardless what the real beginning really was, water was certainly involved in the process some 3,5bln years ago. And since then, Mother Nature designed many ways to benefit of water and to be sheltered from it. Many engineering challenges humans face can be solved by turning to those 3,5bln years of experience and by using natural design as springboard. That’s biologically inspired engineering or, in short, bionics. BIONIC-FINISH®ECO of RUDOLF GROUP is Mother Nature’s work reproduced on textiles and apparel to protect us from water. To perform.

Back in 2003, RUDOLF GROUP borrowed from Mother Nature the idea of dendrimers (from dendron, Greek word for ‘tree’), molecules made of multi-functional branches that interact among themselves, co-crystallize, and self-organize into highly ordered, multicomponent systems. These hyper-branched polymers attach to the textile and embed fluorine-free, durable water-repellent performance.
In 2021 BIONIC-FINISH®ECO comes as a reviewed and extended family of unique nonhalogenated, APEO-free, fluorine-free formulations suited for different materials and designed for different applications and needs. Still very much based on patented dendrimer technology, the new and strengthened BIONIC-FINISH®ECO’s product portfolio:

• Provides non-fluorinated and highly durable water repellent textile finishes for high-performance, professional applications (e.g. when brushing resistance is required);
• Delivers highly efficient and durable performance with low application amounts thus not affecting fabric feel and appearance (e.g. when remarkable softness is important);
• Fulfills a range of challenging technical requirements (e.g. minimal impact on flame retardant properties of technical fibers);
• Is suitable for both sportswear and outdoor applications, as well as for casual apparel and fashion clothing;
• Is bluesign® approved, ZDHC chemical gateway certified and compliant with most RSLs;

BIONIC-FINISH®ECO new portfolio includes universal and versatile solutions targeting the most standard requirements, as well as customized solutions that meet more demanding and specific expectations such as improved resistance to dry-cleaning. “None of us can entirely predict where our voyage will lead” says Dr. Gunther Duschek, RUDOLF GROUP Managing Director. “However, BIONIC-FINISH®ECO of RUDOLF GROUP will always be the fluorine-free, durable water repellent for ultimate  performance. As it is today”.

Anker Carpet (c) Anker
13.10.2020

Anker, Devan and Shark Solutions develop flame retardant aviation carpet

Anker, Devan and Shark Solutions teamed up to create the world’s first flame retardant aviation carpet using a recycled binder. Inspired by the knowledge and the needs of the aviation market, Anker motivated to achieve this new goal together. The PVB binder reuses laminated glass, from windshields and architectural/building glass, that otherwise would go to landfill.

German carpet manufacturer Anker is the first company to offer flame retardant carpets for aviation that are made with a recycled binder. In the search for a more sustainable binder, Anker discovered the PVB from Shark Solutions, a Danish cleantech company focused on giving a new life to post-consumer PVB. Properties of the aviation carpet with PVB as binder are the same as those of traditional non-sustainable carpets. The market has been looking for this type of solutions for a long time and market introduction has already started. Anker will introduce well known and special developed styles of aviation carpets with PVB and plan to take out traditional non-sustainable aviation carpets stepwise as soon as possible.

Anker, Devan and Shark Solutions teamed up to create the world’s first flame retardant aviation carpet using a recycled binder. Inspired by the knowledge and the needs of the aviation market, Anker motivated to achieve this new goal together. The PVB binder reuses laminated glass, from windshields and architectural/building glass, that otherwise would go to landfill.

German carpet manufacturer Anker is the first company to offer flame retardant carpets for aviation that are made with a recycled binder. In the search for a more sustainable binder, Anker discovered the PVB from Shark Solutions, a Danish cleantech company focused on giving a new life to post-consumer PVB. Properties of the aviation carpet with PVB as binder are the same as those of traditional non-sustainable carpets. The market has been looking for this type of solutions for a long time and market introduction has already started. Anker will introduce well known and special developed styles of aviation carpets with PVB and plan to take out traditional non-sustainable aviation carpets stepwise as soon as possible.

Shark’s PVB reuses laminated glass, from windshields and architectural/building glass, that otherwise would go to landfill. The non-toxic binder (no chlorine or phthalates) is fully recyclable and thus lives up to the future standards of the industry.

Textile innovator Devan Chemicals, known for its tailor-made flame retardant solutions, was called in to develop the flame retardant back coating, which is compliant with the Airbus and Boeing safety standards. “Based on many years of experience and competences in customer related developments, improving recycling rates is getting more and more important”, says Dirk Vanpachtenbeke, R&D manager Flame Retardants at Devan. “We are very proud that, together with Anker and Shark Solutions, we can contribute to this rising demand for products that meet the standards of a circular economy solution.”

In other news, Anker and Devan are already working on a new project, which includes Devan’s antimicrobial/viral-reducing technology. Recently, Devan published test results on the activity of their technology (BI-OME®) against SARS-CoV-2 and other viruses. According to independent testing, BI-OME is proven to achieve 99% and higher virus reduction, including of SARS-COV-2, on samples before washing and retains 98.5% even after 25 wash cycles. This technology has been recognized with the 2020 European Technology Innovation Leadership Award by Frost & Sullivan.

Source:

Devan Chemicals NV / Marketing Solutions NV

Baldwin installs six precision spray systems in 60 days for textile manufacturers (c) Baldwin Technology Company Inc.
Baldwin’s TexCoat G4 precision spray system produces ideal results in fabric finishing, because the exact required amount of water and chemistry is always applied.
22.09.2020

Baldwin: six precision spray systems in 60 days for textile manufacturers

  • Fabric finishing and sanforization systems installed in the US and Turkey to enhance productivity

ST. LOUIS - Baldwin Technology Company Inc. has successfully installed six new fabric finishing and sanforizing precision spray systems in the US and Turkey. Despite the COVID-19 pandemic, the installations were completed in just 60 days, thanks to close collaboration between onsite Baldwin textile team members, local agents and remote support from the company’s product and technology center in Sweden.
For textiles, non-wovens and technical textiles, Baldwin’s precision spray technology processes a wide range of low-viscosity water-based chemicals, such as softeners, anti-microbial agents, water repellents, oil  repellents, flame retardants and more.

  • Fabric finishing and sanforization systems installed in the US and Turkey to enhance productivity

ST. LOUIS - Baldwin Technology Company Inc. has successfully installed six new fabric finishing and sanforizing precision spray systems in the US and Turkey. Despite the COVID-19 pandemic, the installations were completed in just 60 days, thanks to close collaboration between onsite Baldwin textile team members, local agents and remote support from the company’s product and technology center in Sweden.
For textiles, non-wovens and technical textiles, Baldwin’s precision spray technology processes a wide range of low-viscosity water-based chemicals, such as softeners, anti-microbial agents, water repellents, oil  repellents, flame retardants and more.

These systems enable fabric producers to significantly reduce chemical and water consumption, while speeding up production times and eliminating production steps, including drying and bath changeovers when switching fabric colors. “Our customers are major manufacturers in fabric dying, finishing and remoistening, and we want to provide outstanding service and support—even in times like this,” said Rick Stanford, Business Development Leader at Baldwin and the commercial leader of the US installations. “Not only does our precision spray technology enhance productivity in their process, but there is also zero waste, which goes hand-in-hand with the increased sustainability focus in the textile industry.”

In North Carolina, two new TexCoat G4 precision spray systems are now in production with major international vertical manufacturers of outdoor living, performance fabrics and automotive fabrics. In Georgia, a major vertical manufacturer of workwear and protective fabrics installed a sanfor precision spray system, which has helped the customer obtain deeper penetration of moisture into fabrics treated with durable water repellents. In Turkey, three new TexCoat G4 systems were installed in Çorlu, northwest of Istanbul, for a large producer of knit fabrics, such as T-shirts. “In Turkey, the manufacturer purchased and installed one TexCoat G4 system before COVID-19, and the customer was so pleased with the results that, during the pandemic, three more were purchased,” said Simone Morellini, Sales Manager- EMEAR at Baldwin and the commercial leader of the Turkish installations. “The systems were manufactured and installed during the lockdown, and now, all four systems are up and running, and being used heavily on a daily basis.” “With the success we have seen, we plan to apply the same strategies for upcoming installations, including the next one in Honduras: strong local management and customer coordination, combined with  effective remote support during the installation,” said Stanford.

Source:

Baldwin Technology Company Inc.

Sustainable leadership for GtA with new Monforts Montex wide width lines (c) AWOL Media
GtA Managing Director Andreas Niess
27.07.2020

Sustainable leadership for GtA with new Monforts Montex wide width lines

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

A new standard in pure white, 100% clean and fault-free textile substrates has been demanded by this market in recent years due to the rapid growth in digitally-printed banners and billboards – often referred to as ‘soft signage’.

The substrates of choice for digital printing are 100% polyester warp knits which are resilient and allow excellent take-up of inks, and vibrant colours and clear and precise images to be achieved with digital printing techniques. The knitted construction also has the advantage of elasticity, which is a plus in terms of flexibility for installers.

Critically, the warp knitted fabrics have extremely smooth surfaces which is becoming increasingly important due to the general move away from PVC coatings which were the standard in the past.

It was to finish these fabrics for Georg and Otto Friedrich GmbH as well as providing such services for many other customers, that the GtA plant in Neresheim, Baden-Württemberg, was established in 2015.

The purpose-built plant on a greenfield site was initially equipped with a fully-automated, 72 metre long Monforts installation comprising a washing machine integrated with a 3.6 metre wide, seven-chamber Montex stenter. The line quickly went from single to double shift production and then to 24/7 operation  to meet demand.

Expanded widths

Building on the success of this installation, GtA has now installed two more Montex stenter lines – both in expanded working widths of 5.6 metres and purpose-built at Montex GmbH in Austria.

A six-chamber Montex unit is combined with a washing machine to guarantee the purity of the substrates, while a five-chamber line is integrated with a wide-width coating machine. This new coating capability at GtA has led to a number of new additions to the Georg and Otto Friedrich DecoTex range for digital printing, including wide width fabrics with flame retardant, antimicrobial and non-slip finishes.

The new Montex stenter lines benefit from all of the latest innovations from Monforts, including the Smart Sensor system for the optimised maintenance planning of key mechanical wear components on the stenters. A comprehensive overview of the condition of all parts at any time is now available for operators within the highly intuitive Qualitex visualization software.

With Qualitex, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

Environmental commitment

GtA is run by a seasoned team of textile professionals led by Managing Director Andreas Niess.

“We have received excellent service from Monforts from the outset and we were happy to place the order for these two new lines as part of our ongoing cooperation,” he says. “With all of the latest Monforts advances in technology we are fully in control of all production and quality parameters with these lines, as part of our significant commitment to innovative environmental technology.”

The GtA plant, which operates in near-cleanroom conditions, has also been equipped with proprietary technology to fully exploit the Monforts air-to-air heat recovery systems that are now standard with Montex stenters.

“Around 30 per cent of our investment volume at the site goes to energy-saving measures and we are sure that this commitment is worthwhile,” Mr Niess says. “As an example, our integrated heat recovery system fully exploits the waste heat from the process exhaust air and the burner exhaust gases of the Monforts stenters, allowing us to achieve an exhaust air temperature of  between 30 to 34°C, compared to what would conventionally be between 140 to 160°C. Another focus has been on exhaust air purification technology and here too, the latest technology has been installed with integrated heat recovery elements.”

This, he adds, saves 52% of the energy that would normally be used – equating to 5,800,000 KwH per year. The necessary audits for energy-efficient companies are also carried out annually.

In addition, GtA has purpose-designed the automatic chemical mixing and dosing systems that feed the padders for the key treatments that are carried out on the fabrics through the stenters.

The company is going further, however, in its pursuit of clean production and raw materials.

"We want to be an asset and not a burden on our immediate environment and therefore do not use any additives containing solvents," Mr Niess says. “We were the first to use fully halogen-free flame retardant chemistry, and we use bio-based, finely ground alumina products for the washing process instead of surfactants. PES polyester yarns made from recycled material are also increasingly used and the latest additions to our raw materials portfolio, the RC-Ocean products, are made from recycled sea plastic.

“We are now planning a combined heat and power plant for the production of electrical energy and heat and we will also build a photovoltaic system that converts solar radiation into electrical energy. GtA wants to be the first textile finishing company to be CO2-neutral in the manufacture of all of its products by 2025. The complete heat supply and heating for the 13,000 square metre production hall, as well as the office building and the hot water supply for the domestic water, is already energy-neutral. We are convinced that this commitment will pay off in the long term and our positive business development proves that sustainability and business profitability are perfectly compatible.”

In addition to the products for Georg and Otto Friedrich GmbH, GtA  offers its manufacturing capacities for other customers as a contract service.

All products are manufactured in accordance with Öko-Tex Standard 100, product class 1 and the company is also involved in the research and development of new sustainable manufacturing processes, in cooperation with many regional universities and funding project partners.

Source:

AWOL Media for A. Monforts Textilmaschinen GmbH & Co. KG

(c) Edward C. Gregor Associates
03.02.2020

Dynamic Modifiers: Highest flame retardancy with new coating

A new non-halogenated FR compound called PAL...VersaCHARTM can achieve a new level of flame retardant performance as a coating for nonwovens and technical textiles.

PAL...VersaCHARTM has been tested to 1,950°C – the highest to date – and shown to prevent all flaming drips of polymer. Char bodies form on the compound surface, protecting against flame creation and delaying heat transfer. Rapid self- extinguishing burn behaviour protects any underlying substrate to which it is adhered.

The compound has passed ASTM E84 (Class A) with a 15/10 rating, which includes ‘clean’ smoke generation of only 2.3% of the allowable ASTM smoke limits. In addition, the compound is light weight, at a specific gravity of 1.0, and 100% non-toxic in every respect, being free from heavy metals, halogens and VOCs. 

Other properties include excellent cold crack performance, hydrophobicity, printability, extreme chemical resistance and the ability to be custom tailored for specific needs such as UV or antimicrobial performance, as volume warrants. The compound is also very competitively priced.

A new non-halogenated FR compound called PAL...VersaCHARTM can achieve a new level of flame retardant performance as a coating for nonwovens and technical textiles.

PAL...VersaCHARTM has been tested to 1,950°C – the highest to date – and shown to prevent all flaming drips of polymer. Char bodies form on the compound surface, protecting against flame creation and delaying heat transfer. Rapid self- extinguishing burn behaviour protects any underlying substrate to which it is adhered.

The compound has passed ASTM E84 (Class A) with a 15/10 rating, which includes ‘clean’ smoke generation of only 2.3% of the allowable ASTM smoke limits. In addition, the compound is light weight, at a specific gravity of 1.0, and 100% non-toxic in every respect, being free from heavy metals, halogens and VOCs. 

Other properties include excellent cold crack performance, hydrophobicity, printability, extreme chemical resistance and the ability to be custom tailored for specific needs such as UV or antimicrobial performance, as volume warrants. The compound is also very competitively priced.

In addition to its use as a coating, PAL...VersaCHARTM compound can be produced as a flexible film or sheet and moulded to shape or over-moulded to most materials, including metal for corrosion resistance. As a polymeric compound it can be cast or calendered and typical durometers from 80-99A for flexible-to-high rigid formats are practical. 

Separately, an adhesive has been created which bonds to many surfaces. In internal evaluations of two laminated plies of woven carbon fibre and two plies of glass fabrics, both passed a 60 second vertical burn with no ply separation, distortion or flaming drips from the adhesive.

Dynamic Modifiers envisages many uses for PAL...VersaCHARTM, from aerospace to the protection of rigid structural materials in building interiors etc.   
 

Monforts at Techtextil India (c) Monforts
A recent Monforts texCoat installation.
20.11.2019

Monforts at Techtextil India

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

As a result, India’s Ministry of Textiles is forecasting that the growth of technical textiles in the country will be over 18% annually in the next few years, from a value of US$16.6 billion in 2018 to US$28.7 billion in 2021.

Value addition

High value-added technical products such as wide-width digital printing substrates, carbon fabrics for high-performance composites, filter media, flame retardant barrier fabrics and heavy-duty membranes are now being coated on Monforts texCoat ranges and finished with the company’s industry-leading Montex stenters.

“Since we acquired the technology that our coating units are based on in 2015, we have made a lot of refinements,” says Hans. “All of these developments are reflected in higher coating accuracy and the resulting quality of the treated fabrics. At the same time, our latest multi-functional coating heads offer an unprecedented range of options, with a wide range of modules available.”

The texCoat user interface is now equipped with the unique Monforts visualisation system and the magnetic doctor blade has greater power reserves. Options include a carbon fibre-reinforced composite coating drum with a more scratch-resistant surface and maximum rigidity and remote control which simplifies exact adjustment for the operator.

Montex stenters in special executions are meanwhile ideal for the drying and finishing of both technical woven fabrics and nonwovens and characterised by high stretching devices in both length and width.

“The European-built Montex range of stenters has earned its leading position in the technical textiles market due to the overall robustness, reliability and economy of these machines,” Hans concludes. “Whatever the intended end-product – and we continue to discover potentially new areas in which technical textiles can be utilised all the time – we have the machine specification and know-how to turn ideas into reality. In India we also benefit from the strong sales and service support of A.T.E. Enterprises.”

Texchtextil India takes place alongside World of Composites at the Bombay Exhibition Centre in Mumbai from November 20-22.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG by AWOL Media.

19.07.2018

Industry-leading brands confirmed for September’s Cinte Techtextil China

As the countdown to the 2018 edition of Cinte Techtextil China enters its last two months, the final exhibitor line-up is starting to take shape. A number of leading international and Chinese brands across the fair’s 12 product application areas will feature at the Shanghai New International Expo Centre from 4 – 6 September, with an expected 500-plus total exhibitors from around 20 countries & regions set to feature.

Nonwovens exhibitor highlights

As the fair’s largest product category, buyers have a wide range of domestic and overseas brands to source from, including:

As the countdown to the 2018 edition of Cinte Techtextil China enters its last two months, the final exhibitor line-up is starting to take shape. A number of leading international and Chinese brands across the fair’s 12 product application areas will feature at the Shanghai New International Expo Centre from 4 – 6 September, with an expected 500-plus total exhibitors from around 20 countries & regions set to feature.

Nonwovens exhibitor highlights

As the fair’s largest product category, buyers have a wide range of domestic and overseas brands to source from, including:

  • Johns Manville (US): who will showcase their polyester spunbond, PP & PBT meltblown, glass fibre nonwoven, micro glass fibre nonwoven, hybrid nonwoven, glass fibre needle mat and glass microfibre product lines among others at the fair.
  •  J.H. Ziegler (Germany): with over 150 years’ expertise and their own production plant in China, they offer products for acoustic absorption in automotive interiors and exteriors, nonwoven foam composites for leather lamination, needle-punched nonwovens, foam nonwoven composites, laminated nonwovens and natural-fibre nonwovens.
  • KOBE-cz (Czech Republic): a new exhibitor to the fair, their nonwoven fabrics, mainly made from glass fibre with temperature resistance up to 800°C, are used for high-temperature isolation in the automotive, marine, energy and building industries. They also have isolation materials made from natural fibres including hemp, wool, cotton and flax.
  • TDF Nonwovens (China): one of the leading domestic brands, their specialties are polyester spunbond geotextiles, polyester filament roofing carriers, filter nonwovens, high-strength coarse denier polypropylene spunbond geotextiles and medical & health nonwovens.
  • Kingsafe (China): they specialise in the production of fusible interlining and nonwoven fabrics for high-end garments.

Yarn & fibre exhibitor highlights

  • Perlon (Germany): has developed a PET based monofilament, HighGrip, which guarantees long-lasting efficiency of conveyor belts, and is available in various types with different tribological characteristics, which they will feature at the fair.
  • Sateri (China): is a global leader in viscose rayon made from 100% dissolving wood pulp, and the largest maker of viscose fibre in China. Their natural and high-quality fibre, made from trees grown on renewable plantations, can be found in textiles and skin-friendly hygiene products.
  • Cordenka (Germany): producers of industrial rayon, their product range covers rayon tire cord, yarn, single-end dipped cord, short-cut fibre and more.
  • EMS-Griltech (Switzerland): will showcase a range of technical fibres & yarns and thermoplastic adhesives at the fair.
  • Barnet (Germany): several finished products (nonwovens, spun yarns and fabrics) made with their specialty fibre will be on display at the fair, including OPAN, para-aramid and carbon filament fibres. The application of their specialty fibre in flame retardant and anti-cut gloves and felts will be shown at their booth for the first time.

Coated textiles & solutions exhibitor highlights

  • Stahl (the Netherlands): the Dutch company will present new products from their water repellent and flame retardant ranges at this year’s fair. According to the company, as the Chinese government continues its efforts to clean up the environment, eco-friendly chemicals remain in strong demand in the country.
  • Sioen (Belgium): will showcase sign materials, truck tarpaulins, tents, membrane fabrics, apparel products, chemicals and specialty products such as inflatable boat fabrics, pool liners and more at Cinte 2018.
  • ROWA Lack (Germany): a new exhibitor at this year’s fair, they will present their special lacquer systems and top coatings.
  • Trelleborg (Sweden): also a new exhibitor, they will display engineered textiles, especially in the fields of outdoor, medical, protective and automotive.
  • FPC Technical Textile (Saudi Arabia): another first-time participant at the fair, they will showcase a range of high-end specialty fabrics including PVC coated fabrics and fibre glass PTFE fabrics.
  • Zhejiang Jinda New Materials (China): this supplier is known for its coated textiles for industrial, transportation and building uses, as well as warp knitted geo-synthetic materials and printable coated materials for advertisements.

Lenzing to showcase its new VEOCEL nonwovens specialty brand at the fair

First announced in June this year, and featuring at Cinte Techtextil, Lenzing’s new VEOCEL brand is billed as a premium range of nonwovens fibres for daily care, which “provides the nonwovens industry with fibres that are certified clean and safe, biodegradable, from botanic origin and produced in an environmentally responsible production process.” Products in this range can be applied to a multitude of uses including baby care, beauty and body care, intimate care and surface cleaning, under the VEOCEL Beauty, VEOCEL Body, VEOCEL Intimate and VEOCEL Surface brands.

 

More information:
Cinte Techtextil China
Source:

Messe Frankfurt (HK) Ltd

03.05.2018

Clariant debuted additive solutions and launched AddWorks® at Chinaplas 2018

•    New, sustainable, ready-to-use solutions for plastic auto parts to support China’s electric vehicle boom
•    Stronger, softer nylon polyamide fibers plus fast processing for clothes, carpets & industrial applications
•    AddWorks blends lower total cost of ownership & reduce production complexity while enhancing performance

Muttenz, May 3, 2018 – Clariant, a world leader in specialty chemicals, introduced new additive solutions for plastics materials at Chinaplas 2018.

“Our innovations focus on higher performance at better convenience for a sustainable future,” says Stephan Lynen, Head of Clariant BU Additives. “At Chinaplas 2018 we demonstrated our technical and market capabilities around the theme of e-mobility. The immense changes in mobility call for lighter, safer and smarter vehicles. We offer new additive solutions, such as AddWorks, and technical capabilities to respond to this demand. We are accompanying this with a series of investments such as new production facilities in China.”

•    New, sustainable, ready-to-use solutions for plastic auto parts to support China’s electric vehicle boom
•    Stronger, softer nylon polyamide fibers plus fast processing for clothes, carpets & industrial applications
•    AddWorks blends lower total cost of ownership & reduce production complexity while enhancing performance

Muttenz, May 3, 2018 – Clariant, a world leader in specialty chemicals, introduced new additive solutions for plastics materials at Chinaplas 2018.

“Our innovations focus on higher performance at better convenience for a sustainable future,” says Stephan Lynen, Head of Clariant BU Additives. “At Chinaplas 2018 we demonstrated our technical and market capabilities around the theme of e-mobility. The immense changes in mobility call for lighter, safer and smarter vehicles. We offer new additive solutions, such as AddWorks, and technical capabilities to respond to this demand. We are accompanying this with a series of investments such as new production facilities in China.”

Clariant’s new AddWorks solutions – AddWorksATR 146, AddWorks LXR 568 and AddWorks TFB 117 – are specifically aimed at improving performance and efficiency of plastics materials for compounders, polymer and fiber producers in China’s major plastics manufacturing segments. All three solutions are part of the globally available portfolio.

The full AddWorks portfolio consists of differentiated market-specific synergistic additive blends that streamline production processes and create value for customers while enhancing performance. Each solution is customized to specific market needs, underlined by broader considerations such as emission reduction, and less energy and resource usage.

Sustainability and performance for the world’s largest auto market
To support the significant investment in electric vehicles in China, Clariant launched two additive innovations that improve the lifetime of lightweight automotive parts and under-the-hood applications and reduce VOC emissions in an easy to use single solution.

AddWorks ATR 146 is a new low dosage, sulfur-free heat and light stabilizer for filled polypropylene (TPO) compounds used in interior applications. Its exceptional heat and light stability and long term color retention offers the automotive industry unmatched performance. It shows no surface cracking after 700 hours at 150°C, which enables dashboards, instrument panels, door panels and pillars to maintain their aesthetics longer than with traditional stabilizers. It also contributes to reducing blooming and VOC emissions, supporting the common effort to make automotive interiors healthier and odorless.

AddWorks LXR 568 is a high performance processing stabilizer that helps to prevent plastic resins, especially polyolefins, from degradation at high processing temperatures. For the automotive industry, this reduces the tendency of injection molded polypropylene interior car parts to turn brittle during heat exposure, enabling them to maintain a defect-free surface. It also has low migration and low fogging that support healthier in-cab environments.

AddWorks LXR 568 combines outstanding color and melt flow protection with good resistance to hydrolysis and high thermal stability. This makes it ideal for interior and under-the-hood powertrains and wider application areas such as packaging films. It is available in free-flowing pills and micro-pills which are easy and convenient to use.

Softer, stronger polyamide fibers for clothes, carpets and industrial applications
Within the next three years, China is expected to account for 40% of the world’s nylon production and more than 30% of the nylon resin consumed globally[1]. The new AddWorks TFB 117 offers a number of benefits to help stabilize and smoothen fiber production processes, protect color, and improve heat stability and mechanical properties of fibers. AddWorks TFB 117 ensures smooth spinnability with less filaments breakage, even at low processing temperatures and at high speed spinning up to 5,500 m/min.

Martin P. J. John, Head of BL Performance Additives at Clariant, comments: “AddWorks solutions are an ideal fit with China’s priority of achieving more sustainable production. They save time and reduce complexity along the production process, with easy to use formats that reduce health risk and chemical waste. Our new state-of-the-art production facility in Zhenjiang, China, which opens later this year, is dedicated to the manufacturing of AddWorks to deliver innovative solutions tailored to the needs of the market. Made for China in China.

In addition to AddWorks, Clariant presented Exolit® OP 1400, a highly stable non-halogenated flame retardant enhancing safety during the charging process. It also provides outstanding thermal stability for under the hood applications. Exolit OP 1400 has been awarded the Clariant EcoTain® label for outstanding sustainability and performance.  

Clariant also introduced two ranges of performance waxes that smoothen the production of automotive plastics for under the hood applications, Licowax® and Licocare® RBW. The recently launched Licocare RBW is a series of multi-purpose additives based on crude rice bran wax. They offer better shaping flexibility, better mechanical properties and enhanced surface finish, which results in a reduced rejection rate and a more effective dosage.

Source:

EMG PR