From the Sector

Reset
25 results
07.07.2022

Successful SMCCreate design conference in Antwerp

With over 60 participants from Europe and Turkey, the first SMCCreate Design Conference took place in Antwerp from 28-29 June. The conference was jointly organised by AVK – Federation of Reinforced Plastics and the European Allicance for SMC BMC. The topics covered the wide spectrum of SMC and BMC manufacturing, from design to sustainability solutions. 16 speakers from different European countries showed what is important in component manufacturing and design, and which solutions the companies offer in regard to materials, performance and much more.

After an overview of the general market developments and how the economic requirements affect component manufacturing, the focus was on the possibilities to enable sustainable design with SMC/BMC. In the second conference section „part design“, the topics of design and modelling, design with structural analysis and flow simulation, standards, and best class solutions as well as surface modification were presented.

With over 60 participants from Europe and Turkey, the first SMCCreate Design Conference took place in Antwerp from 28-29 June. The conference was jointly organised by AVK – Federation of Reinforced Plastics and the European Allicance for SMC BMC. The topics covered the wide spectrum of SMC and BMC manufacturing, from design to sustainability solutions. 16 speakers from different European countries showed what is important in component manufacturing and design, and which solutions the companies offer in regard to materials, performance and much more.

After an overview of the general market developments and how the economic requirements affect component manufacturing, the focus was on the possibilities to enable sustainable design with SMC/BMC. In the second conference section „part design“, the topics of design and modelling, design with structural analysis and flow simulation, standards, and best class solutions as well as surface modification were presented.

A rather newer field was highlighted on Day 2 with Carbon SMC, discussing mobility and automotive applications. These included the integration of multiple material technologies, not forgetting the possibility of implementing green deal strategies here too. The advantages of SMC in automotive components for electrification were explained in more detail. The conference concluded with a sporty presentation on the development of a carbon SMC rear frame for a downhill mountain bike.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

05.07.2022

ITM 2022: Bringing Textile Technology Leaders together

ITM 2022 hosted textile technology leaders in Istanbul for 5 days, presenting the latest innovations in every field of textile from weaving, knitting, yarn, digital printing, finishing to denim. The ITM 2022 Exhibition, where a business volume of over 1.5 billion Euros was created in 5 days, accelerated the Turkish and world economy.

Organized by the partnership of Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc., ITM 2022- International Textile Machinery Exhibition was held at Tüyap Fair and Congress Center between 14-18 June.  ITM 2022 Exhibition, attended by 1280 companies and company representatives from 65 countries, was visited by 64,500 people from 102 countries, consisting of 44% international and 56% domestic visitors.

ITM 2022 hosted textile technology leaders in Istanbul for 5 days, presenting the latest innovations in every field of textile from weaving, knitting, yarn, digital printing, finishing to denim. The ITM 2022 Exhibition, where a business volume of over 1.5 billion Euros was created in 5 days, accelerated the Turkish and world economy.

Organized by the partnership of Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc., ITM 2022- International Textile Machinery Exhibition was held at Tüyap Fair and Congress Center between 14-18 June.  ITM 2022 Exhibition, attended by 1280 companies and company representatives from 65 countries, was visited by 64,500 people from 102 countries, consisting of 44% international and 56% domestic visitors.

Turkey became a Supply Center at the ITM 2022 Exhibition
The successful sales graph achieved at the ITM 2022 Exhibition proved that the difficulties experienced due to the pandemic for the last 3 years have been left behind. Turkey has become a supply center for European, Middle Eastern and African countries, especially with the disruption of the supply chain in Far East countries, including China. The profile of the professional visitors visiting the ITM 2022 Exhibition revealed that in the new world order that has shifted after the pandemic, the trade network has also changed hands and new players have appeared on the scene. The fact that manufacturers from all over the world such as Andorra, Angola, Honduras, Peru, Seychelles, Sierra Leone, Brazil, Sri Lanka, Tanzania, Egypt, Iran, and Oman purchased a large number of machinery and signed collaborations at the ITM 2022 Exhibition has proven this.

Exhibitors of ITM 2022 enlarge their stands for ITM 2024
Many company officials, who stated that they have achieved a sales graphic far above their expectations starting from the very first day of the ITM 2022 Exhibition and that they have hosted visitors from all over the world, decided to enlarge their stands at the ITM 2024 Exhibition. During the exhibition, companies visited the registration application points and applied for ITM 2024 participation.

The next meeting of the ITM and HIGHTEX Exhibitions will be held in Istanbul between 4-8 June 2024.

Source:

ITM / Teknik Fairs INC.

13.06.2022

ITM 2022: Bringing Textile Technology Leaders Together

ITM 2022, the first major international textile machinery exhibition to be held in the world after a 3-year hiatus during the pandemic process, is getting ready to open its doors. Bringing the leading brands of textile technologies together in Istanbul, ITM 2022 will host world launches and numerous collaborations for 5 days.

ITM 2022- International Textile Machinery Exhibition, organized in partnership with Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc, will open its doors at Tüyap Fair and Congress Center between 14-18 June. For ITM 2022, which will be held in 12 halls on an area of 120,000 m2; hums of 1280 participating companies from more than 40 countries continues. Tüyap Fairground, where thousands of people sweat for stand setups, is getting ready for the big meeting. ITM 2022, where all halls have reached 100% occupancy rate and 1280 exhibitor companies are located, will also attract attention with the stand areas and machine parks that the manufacturers have enlarged compared to the previous exhibitions.

ITM 2022, the first major international textile machinery exhibition to be held in the world after a 3-year hiatus during the pandemic process, is getting ready to open its doors. Bringing the leading brands of textile technologies together in Istanbul, ITM 2022 will host world launches and numerous collaborations for 5 days.

ITM 2022- International Textile Machinery Exhibition, organized in partnership with Teknik Fairs Inc. and Tüyap Tüm Fuarcılık Yapım Inc, will open its doors at Tüyap Fair and Congress Center between 14-18 June. For ITM 2022, which will be held in 12 halls on an area of 120,000 m2; hums of 1280 participating companies from more than 40 countries continues. Tüyap Fairground, where thousands of people sweat for stand setups, is getting ready for the big meeting. ITM 2022, where all halls have reached 100% occupancy rate and 1280 exhibitor companies are located, will also attract attention with the stand areas and machine parks that the manufacturers have enlarged compared to the previous exhibitions.

Companies will showcase their state-of-the-art technologies for the first time at ITM 2022
Many companies that focus on product development and new productions under pandemic conditions will have the opportunity to introduce their products to their customers for the first time in 3 years at the ITM 2022 Exhibition. Company owners, managers, employees and sector representatives visiting the exhibition will have the opportunity to see the latest technological innovations for the first time and witness their world launches.

Sector representatives, who will open up new horizons in their minds about textile technologies, will sign new products by transforming the extraordinary and original ideas that they have obtained at the ITM 2022 Exhibition into design. Participating companies will also update their machines in line with the demands and needs from the sector representatives and lead the development of new technologies.

Significant Contribution to Exports Aimed with Machine Sales and New Investment Decisions
The textile industry, which is among the locomotive sectors in Turkey's exports, has made a significant contribution to the Turkish economy, especially with the performance increase it has achieved during the pandemic period. Having achieved an increase of up to 40 percent in its exports of textiles and raw materials, Turkey also managed to increase its exports of medical textiles, technical textiles and home textiles. The industry will further increase this success with the collaborations to be realized at ITM 2022. The textile machinery industry will gain great momentum with the machinery sales and new investment decisions to be made at the exhibition.

ITM 2022, which will be attended by many domestic and foreign companies and visited by thousands of people, will be an organization where both domestic and foreign companies will make sales amounting to millions of Euros and many business connections will be realized.

Intense Interest from Trade Delegations
Trade delegations from dozens of countries are requesting to attend the ITM 2022 Exhibition, which is included in the ‘Domestic Organizations Covered by State Incentives’ list by the Ministry of Commerce. Bangladesh, India, Iran, Serbia, Czech Republic, Pakistan, Indonesia, Ethiopia, Malaysia, Mexico, Egypt and Vietnam are among the countries that requested procurement delegations. The intense application of visitors to consulates and commercial attachés from all over the world clearly reveals that ITM 2020 will host a large number of visitors.

ITM 2022 Exhibition Prepares to Break Both Exhibitor and Visitor Records
Company owners, company representatives and visitors left the 2018 edition of the ITM Exhibition very satisfied. ITM 2018 Exhibition, attended by 1150 companies and company representatives from 64 countries and visited by approximately 60 thousand people from 94 countries made a significant contribution to the export records of the textile industry that year. At the ITM 2022; It is getting ready to break new records with the number of participants and visitors coming from Turkey and abroad.

Technical Textiles and Nonwovens Industry Will Meet at HIGHTEX 2022 Exhibition
On the other hand, HIGHTEX 2022 Exhibition, which will be held simultaneously with the ITM 2022 Exhibition, will be an exhibition where Nonwoven products, raw materials used in their production and the state-of-the-art technologies will be exhibited. HIGHTEX 2022 Exhibition, which is the first and only in its field in Turkey, will host a record number of participants and visitors in parallel with the increase in demand for technical textiles. At the HIGHTEX 2022 Exhibition, companies operating in many sectors, from medical textiles to hygienic textiles, from agricultural textiles to geotextiles, will exhibit their latest products and production technologies. Nonwoven manufacturers will come together with the global players of the sector and have the opportunity to both invest in technology and introduce their newest products.

More information:
ITM
Source:

ITM

26.01.2022

World Pultrusion Conference - Postponed

  • The 16th World Pultrusion Conference will be postponed to 5-6 May 2022

The EPTA – European Pultrusion Technology Association in cooperation with the American Composites Manufacturers Association (ACMA) will postpone the 16th World Pultrusion Conference to 5-6 May 2022 due to the corona situation and the postponement of the JEC World, with which there is a close partnership.

This conference takes place every two years and is the meeting point of the European and worldwide Pultrusion Industry. More than 25 international speakers from Belgium, Germany, France, Spain, The Netherlands, Turkey, UK and the USA will present practical presentations about innovative applications, technologies and processes. Equally current market trends and developments are on the agenda.
This World Pultrusion Conference takes now place on 5-6 May 2022 in Paris, France. The presentation language will be English. The program, further details and registration information is available at www.pultruders.com.

  • The 16th World Pultrusion Conference will be postponed to 5-6 May 2022

The EPTA – European Pultrusion Technology Association in cooperation with the American Composites Manufacturers Association (ACMA) will postpone the 16th World Pultrusion Conference to 5-6 May 2022 due to the corona situation and the postponement of the JEC World, with which there is a close partnership.

This conference takes place every two years and is the meeting point of the European and worldwide Pultrusion Industry. More than 25 international speakers from Belgium, Germany, France, Spain, The Netherlands, Turkey, UK and the USA will present practical presentations about innovative applications, technologies and processes. Equally current market trends and developments are on the agenda.
This World Pultrusion Conference takes now place on 5-6 May 2022 in Paris, France. The presentation language will be English. The program, further details and registration information is available at www.pultruders.com.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

16.07.2021

Eruslu Nonwovens Group: Entering Biodegradable Nonwoven Market with Truetzschler Nonwovens’ Machinery

Truetzschler Nonwovens will deliver equipment to enlarge an existing spunlacing line - put into operation in 2015 at the Turkish Eruslu Nonwovens Group - into a flexible, state-of-the-art production line for various light to heavy weight sustainable nonwovens.

Last year Eruslu decided to broaden its portfolio in the wipes segment by adding biodegradable products from renewable resources. The group took full advantage of the 2015 small capacity line and went for:

  • a second NCR random and a NCA airlay card
  • fiber preparation and card feeding equipment for the two new cards
  • more hydraulic power to reliably and efficiently hydroentangle multi-layer webs
  • an extension to the dryer for increased evaporation capacity

After starting up in the second half of 2022, Eruslu will be operating an ultra-modern, highly flexible NCR-NCA-NCR spunlace line, the first of its kind in Turkey. The line is tailor-made to process virgin cotton fibers, comber noils and short fibers at high speeds. End products are top-quality, lightweight natural wipes or heavy-weight, three-layer nonwovens for cosmetic pads.

Truetzschler Nonwovens will deliver equipment to enlarge an existing spunlacing line - put into operation in 2015 at the Turkish Eruslu Nonwovens Group - into a flexible, state-of-the-art production line for various light to heavy weight sustainable nonwovens.

Last year Eruslu decided to broaden its portfolio in the wipes segment by adding biodegradable products from renewable resources. The group took full advantage of the 2015 small capacity line and went for:

  • a second NCR random and a NCA airlay card
  • fiber preparation and card feeding equipment for the two new cards
  • more hydraulic power to reliably and efficiently hydroentangle multi-layer webs
  • an extension to the dryer for increased evaporation capacity

After starting up in the second half of 2022, Eruslu will be operating an ultra-modern, highly flexible NCR-NCA-NCR spunlace line, the first of its kind in Turkey. The line is tailor-made to process virgin cotton fibers, comber noils and short fibers at high speeds. End products are top-quality, lightweight natural wipes or heavy-weight, three-layer nonwovens for cosmetic pads.

Source:

Trützschler Nonwovens & Man Made Fibers GmbH

HIGHTEX Trade Fair postponed to 14-18 June 2022 (c) ITM
15.03.2021

HIGHTEX Trade Fair postponed to 14-18 June 2022

HIGHTEX International Technical Textiles and Nonwoven Trade Fair, which is planned to be held on June 22-26, 2021 was decided to postpone to June 14-18, 2022, considering the effects of the ongoing Covid-19 pandemic in the world. This postponement decision was taken as a result of intense discussions and evaluations with our participants and sector representatives.

The HIGHTEX Organization Team made the following statements: “We as HIGHTEX Organization Team, our priority is to protect your valuable exhibitors and visitors’ investments and all rights, not our commercial earnings. In this regard, we believe that all of our participants will find this compulsory postponement decision taken for the HIGTEX Exhibition justified and will understand.”

HIGHTEX 2022, which will be held in Istanbul Tuyap Fair and Congress Center between 14- 18 June 2022, simultaneously with the ITM 2022 Exhibition.

HIGHTEX International Technical Textiles and Nonwoven Trade Fair, which is planned to be held on June 22-26, 2021 was decided to postpone to June 14-18, 2022, considering the effects of the ongoing Covid-19 pandemic in the world. This postponement decision was taken as a result of intense discussions and evaluations with our participants and sector representatives.

The HIGHTEX Organization Team made the following statements: “We as HIGHTEX Organization Team, our priority is to protect your valuable exhibitors and visitors’ investments and all rights, not our commercial earnings. In this regard, we believe that all of our participants will find this compulsory postponement decision taken for the HIGTEX Exhibition justified and will understand.”

HIGHTEX 2022, which will be held in Istanbul Tuyap Fair and Congress Center between 14- 18 June 2022, simultaneously with the ITM 2022 Exhibition.

HIGHTEX 2022 being the first and only exhibition in its field in Turkey will host the world's leading technical textile and nonwoven manufacturers in Istanbul for 5 days.
HIGHTEX 2022, where many companies from Turkey and abroad will exhibit their latest technologies and products; will be visited by many industry professionals from medical to ready-to-wear, from decoration to cosmetics, from automotive to defense.

Source:

HIGHTEX

Photo: ANDRITZ
02.02.2021

ANDRITZ to supply a Wetlace™ CP line to Lotus Teknik, Turkey

International technology Group ANDRITZ has received an order from Lotus Teknik A.Ş., Turkey, to supply a neXline wetlace CP (carded pulp) line for the production of biodegradable, plastic-free wet wipes. Lotus Teknik A.Ş. is a leading nonwoven roll good producer and a member of the Sapro group. Sapro is based in Istanbul, Turkey, and is one of the top three producers of wet wipes globally.  

The neXline wetlace CP line is equipped with state-of-the-art stock preparation equipment, including approach flow and fan pump, opening and blending, TT card, wetlaid forming unit for pulp application, a hydroentanglement system, filtration unit, dewatering, and through-air drying. All components are perfectly designed to produce a first-class biodegradable wipe. The line is scheduled for start-up by the end of 2021.

International technology Group ANDRITZ has received an order from Lotus Teknik A.Ş., Turkey, to supply a neXline wetlace CP (carded pulp) line for the production of biodegradable, plastic-free wet wipes. Lotus Teknik A.Ş. is a leading nonwoven roll good producer and a member of the Sapro group. Sapro is based in Istanbul, Turkey, and is one of the top three producers of wet wipes globally.  

The neXline wetlace CP line is equipped with state-of-the-art stock preparation equipment, including approach flow and fan pump, opening and blending, TT card, wetlaid forming unit for pulp application, a hydroentanglement system, filtration unit, dewatering, and through-air drying. All components are perfectly designed to produce a first-class biodegradable wipe. The line is scheduled for start-up by the end of 2021.

ANDRITZ developed the new neXline wetlace CP line in order to serve the new market trend of sustainable wipes. Lotus Teknik supported the development from a roll goods producer and converter perspective. The partnership follows the successful installation of an ANDRITZ high-capacity spunlace line some years ago. The Wetlace CP new generation of production technology for biodegradable wipes has resulted from ANDRITZ’s extensive knowledge and considerable history of providing technologies for wood-based industries, spunlace and wetlaid roll goods, and the strong collaboration with Lotus Teknik.

Source:

ANDRITZ

27.01.2021

Rieter: First Information on the Financial Year 2020

Order Intake Continued to Recover in the Fourth Quarter of 2020:

  • Order intake increased to CHF 215.1 million in the fourth quarter of 2020 and reached a total of CHF 640.2 million in the 2020 financial year
  • As expected, sales of CHF 573.0 million in the 2020 financial year were significantly down on the previous year
  • EBIT margin of around -15% and net profit of around -16% of sales expected
  • First half of 2021 still heavily impacted by the COVID-19 pandemic
  • Change to the Group Executive Committee

Rieter posted a globally and broadly supported order intake of CHF 215.1 million in the fourth quarter of 2020. Thus, the recovery that began in the third quarter of 2020 after the slump in demand in the second quarter continued (order intake second quarter: CHF 45.7 million, third quarter: CHF 174.4 million). Overall, Rieter’s annual order intake for the 2020 financial year totaled CHF 640.2 million, which corresponds to a decrease of 31% compared to the previous year.

Order Intake Continued to Recover in the Fourth Quarter of 2020:

  • Order intake increased to CHF 215.1 million in the fourth quarter of 2020 and reached a total of CHF 640.2 million in the 2020 financial year
  • As expected, sales of CHF 573.0 million in the 2020 financial year were significantly down on the previous year
  • EBIT margin of around -15% and net profit of around -16% of sales expected
  • First half of 2021 still heavily impacted by the COVID-19 pandemic
  • Change to the Group Executive Committee

Rieter posted a globally and broadly supported order intake of CHF 215.1 million in the fourth quarter of 2020. Thus, the recovery that began in the third quarter of 2020 after the slump in demand in the second quarter continued (order intake second quarter: CHF 45.7 million, third quarter: CHF 174.4 million). Overall, Rieter’s annual order intake for the 2020 financial year totaled CHF 640.2 million, which corresponds to a decrease of 31% compared to the previous year.

At the end of 2020, the company had an order backlog of about CHF 560 million (December 31, 2019: about CHF 500 million).

As expected, as a consequence of the economic effects of the COVID-19 pandemic, the Rieter Group closed the 2020 financial year with considerably lower sales than in the previous year. According to the first, as yet unaudited figures, total sales of CHF 573.0 million were achieved, which corresponds to a decrease of 25% compared to the previous year (2019: CHF 760.0 million).

Order Intake by Business Group
All three business groups were affected by the slump in demand in the second quarter of 2020 due to the COVID-19 pandemic. Despite the recovery in order intake in the third and fourth quarters of 2020, the weak second quarter was only partially offset.

The Business Group Machines & Systems was particularly hard hit by the effects of the pandemic, with a year-on-year decline of 35%. The Business Groups Components and After Sales each recorded a 24% reduction in order intake.*

Sales by Business Group
The exceptional market situation in 2020 gave rise to a significant decline in sales in all three business groups. Accordingly, reluctance to invest and deferred deliveries by customers caused sales in the Business Group Machines & Systems to decline by 24% compared to the previous year.

Due to COVID-19, a large number of spinning mills stopped production worldwide. This led to low demand for spare parts and wear parts, especially in the second and third quarters of 2020. Accordingly, compared to the previous year, sales in the Business Groups Components and After Sales fell by 24% and 27% respectively in the 2020 financial year.*

Sales by Region
With the exception of Turkey, all regions were affected by the low demand as a consequence of the COVID-19 pandemic.*

EBIT Margin and Net Profit
In the 2020 financial year, Rieter anticipates an EBIT margin of around -15% (2019: 11.2%) and net profit of around -16% of sales (2019: 6.9%). As of December 31, 2020, Rieter had liquid funds of exceeding CHF 280 million and unused credit lines in the mid three-digit million range.

First Half of 2021 Still Heavily Impacted by the COVID-19 Pandemic
Thanks to the improved capacity utilization, Rieter is planning short-time working in only a few areas in the first half of 2021. Nevertheless, Rieter expects sales in the first half of 2021 to be below the break-even point.*

Change to the Group Executive Committee
With effect from March 1, 2021, the Board of Directors of Rieter Holding Ltd. has appointed Roger Albrecht as Head of the Business Group Machines & Systems and a member of the Group Executive Committee.*

Annual General Meeting April 15, 2021
The 2021 Annual General Meeting of Rieter Holding Ltd. will take place in Winterthur on April 15, 2021.*


*See attached document for more information.

Source:

Rieter Management AG

Global Success of Technical Textiles will be Reflected in HIGHTEX 2021 (c) HIGHTEX 2021
International Technical Textiles and Nonwoven Fair
28.12.2020

Global Success of Technical Textiles will be Reflected in HIGHTEX 2021

  • The nonwoven and technical textiles industry has become the focus of the whole world during the pandemic process.
  • Most countries carried out works for these sectors with their investments, production and innovations.

During the pandemic process, a new one is added every day to the works for the nonwoven and technical textiles sector, whose importance is increasing in line with the needs. Turkey has become a center of  technical textiles by showing that its accumulation in these field and power.

In the Turkish technical textiles sector, which has an export market of 107 billion dollars worldwide and continues to break its own export record every month, R&D and innovation investments continue without slowing down. Technical textile exports, which increased by 77 percent in last November compared to the same month of the previous year, increased by 55 percent in January - November period and reached 2.5 billion dollars. Thus, technical and smart textiles and production technologies both attracted more attention and gained more importance in line with the needs of the pandemic process.

  • The nonwoven and technical textiles industry has become the focus of the whole world during the pandemic process.
  • Most countries carried out works for these sectors with their investments, production and innovations.

During the pandemic process, a new one is added every day to the works for the nonwoven and technical textiles sector, whose importance is increasing in line with the needs. Turkey has become a center of  technical textiles by showing that its accumulation in these field and power.

In the Turkish technical textiles sector, which has an export market of 107 billion dollars worldwide and continues to break its own export record every month, R&D and innovation investments continue without slowing down. Technical textile exports, which increased by 77 percent in last November compared to the same month of the previous year, increased by 55 percent in January - November period and reached 2.5 billion dollars. Thus, technical and smart textiles and production technologies both attracted more attention and gained more importance in line with the needs of the pandemic process.

HIGHTEX 2021 International Technical Textiles and Nonwoven Fair, which will be held at Tüyap Fair and Congress Center on 22-26 June 2021, will be the exhibition where the latest technologies and products for nonwoven, technical and smart textiles which have become more important during the pandemic period and have become the focus of the whole world. Especially the products and technologies produced for the pandemic will attract more attention at the exhibition. HIGHTEX 2021 Exhibition, which will gather its exhibitors and visitors under one roof, will also allow new collaborations. At the same time, the exhibition, where developing technologies and products are exhibited, will provide a great advantage in terms of the formation of new business ideas.
HIGHTEX 2021, the first and only exhibition in Turkey in its field are expected to sign a new record in terms of number of exhibitors and visitors. You can visit www.hightexfairs.com website for more information about HIGHTEX 2021, which is preparing to attract more attention and host people than ever before.

Turkish textile manufacturers wait for ITM 2021 Exhibition (c) ITM
10.12.2020

Turkish textile manufacturers wait for ITM 2021 Exhibition to expand their investments

The Turkish textile industry, which continues its exports and investments without slowing down despite the devastating pandemic, once again proved its strength, especially in this period. ITM 2021 Exhibition, which will be held in Istanbul between 22 and 26 June 2021, will provide a great advantage to companies that desire to expand their investments and introduce their brand new technologies.

The Turkish textile industry, which continues its exports and investments without slowing down despite the devastating pandemic, once again proved its strength, especially in this period. ITM 2021 Exhibition, which will be held in Istanbul between 22 and 26 June 2021, will provide a great advantage to companies that desire to expand their investments and introduce their brand new technologies.

Although there were slowdowns in the textile industry in April and May this year due to the troublesome coronavirus pandemic , the Turkish textile industry succeeded a big breakthrough with the removal of restrictions in June, thanks to both its textile production infrastructure and international exports capacity. The exports of the textile and raw materials sector increased and the companies turned to new investments. While many local companies enlarged their facilities, some of them made new investment decisions. For example, while a giant hygienic and medical fabric production facility was invested in Çorlu, another Turkish company, a global brand in textile machinery production, decided to invest 40 million Turkish Lira. Gaziantep-based spunbond and meltblown nonwoven manufacturer company added two new meltblown lines to its operations. Another company also began to invest in the production of raw materials that they import. This investment activity in Turkey, where is a manufacturing base of European customers whet the appetite of international investors. One of South Korea's largest conglomerates has rolled up its sleeves for an investment of 430 million US Dollars in Çerkezköy. Due to the investments, the purchase of textile machinery increased by 37.1 percent in the first nine months of 2020 amounting to over 1 billion US Dollars.

The Accurate Address for Investment Decisions: ITM 2021 Exhibition
Although the companies took advantage of the pandemic period as an opportunity and continued their investments, many of them are waiting for the ITM 2021 Exhibition for large machinery purchases. ITM 2021 Exhibition, which will be held between 22 and 26 June 2021 at Istanbul Tüyap Fair and Congress Center, will gather thousands of participating companies and visitors under one roof. The company officials, who will have the opportunity to observe the latest technological products to be exhibited by the international and domestic exhibitors, will direct their investments by meeting with the experts of the sector. The machines produced for technical textiles, which became even more important during the devastating pandemic period, will attract the attention of visitors. Thanks to the machinery purchases and business partnerships of both domestic and international companies, there will be great dynamism in the textile industry and the national economy.

Source:

ITM

Advanced Monforts automation is the key for Hamle (c) Monforts
07.12.2020

Advanced Monforts automation is the key for Hamle

  • Leading Turkish textile printing company Hamle has installed a new Monforts Thermex dyeing range as part of its ongoing strategy of continuous investment.

“Investment in new technology and capacity expansions are very important to us, in order to stay ahead in terms of sustainable, high quality production,” says general manager Gürkan Uzuner. “We carefully assess the benefits of each advanced new technology in order to thrive in a sector that is constantly changing.

“The Zara Group is a major European customer for us, along with well-known Turkish brands such as LCW and De-Facto, and it’s no accident that Çorlu, due to its proximity to Istanbul and the ease of supplying to Europe, has become the epicentre of Turkish textile production. The quality of textiles coming from the region is now very well proven.”

Integration

  • Leading Turkish textile printing company Hamle has installed a new Monforts Thermex dyeing range as part of its ongoing strategy of continuous investment.

“Investment in new technology and capacity expansions are very important to us, in order to stay ahead in terms of sustainable, high quality production,” says general manager Gürkan Uzuner. “We carefully assess the benefits of each advanced new technology in order to thrive in a sector that is constantly changing.

“The Zara Group is a major European customer for us, along with well-known Turkish brands such as LCW and De-Facto, and it’s no accident that Çorlu, due to its proximity to Istanbul and the ease of supplying to Europe, has become the epicentre of Turkish textile production. The quality of textiles coming from the region is now very well proven.”

Integration

Hamle’s plant in Çorlu already houses a Monforts ten-chamber Montex stenter and two Monforts sanforizing ranges on which the company carries out an extensive range of finishing processes. The new Thermex range further integrates a number of processes on technology all from a single supplier. The Thermex universal hotflue for continuous dyeing, condensing and thermosoling achieves unrivalled reliability even at maximum fabric speeds, for exceptional cost-effectiveness when dyeing both large and small batches of woven fabrics. The new range installed for Hamle benefits from the Econtrol® process* for reactive dyestuffs. This is quick and economical one-pass pad-dry and wash off process, with drying in the hot flue at 120-130°C and controlled humidity (25-30% by volume) to obtain fixation in 2-3 minutes.
Econtrol® ensures excellent reproducibility of all colours, improved dye penetration on difficult fabrics and no risk of the browning of cotton or other cellulose fibres due to the low fixation temperature.

As such, it is the ideal process for fast change technology and operational savings. “The new Thermex range has some very advanced automation features which ensure our machine operators have full control over the entire system,” Mr Uzuner concludes. “ As the Monforts representative in Turkey, Neotek has been our solution partner in the installation and commissioning and has been with us every step of the way.
.
* Econtrol® is a registered mark of DyStar Colours Distribution GmbH, Germany.

 

Source:

AWOL Media for Monforts

Monforts (c) Monforts
19.11.2020

İlay puts a premium on energy with new Monforts installation

The company, founded in 1993, has established a reputation for leadership in new printing techniques and technologies with customers across Europe, as well as with many of the leading Turkish brands.

Mission
On its mission to achieving continuous progress in error-free and resource-efficient manufacturing, İlay has just taken delivery of a new Monforts Montex stenter range, with a working width of two metres and eight TwinAir chambers.

“This installation provides us with much improved control options for all process parameters and compared to the old stenter it is replacing, we are particularly impressed with the energy savings we are making,” Mr Savaş says.

Achieving energy savings on Montex stenters has been a key focus for Monforts designers and engineers in Germany for many years.

The company, founded in 1993, has established a reputation for leadership in new printing techniques and technologies with customers across Europe, as well as with many of the leading Turkish brands.

Mission
On its mission to achieving continuous progress in error-free and resource-efficient manufacturing, İlay has just taken delivery of a new Monforts Montex stenter range, with a working width of two metres and eight TwinAir chambers.

“This installation provides us with much improved control options for all process parameters and compared to the old stenter it is replacing, we are particularly impressed with the energy savings we are making,” Mr Savaş says.

Achieving energy savings on Montex stenters has been a key focus for Monforts designers and engineers in Germany for many years.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying.

The resulting constant evaporation rate within the stenter ensures optimum energy utilisation. In addition, TwinAir chambers feature special panelling for low heat radiation, careful sealing of all connecting positions and chamber access points, and air locks at both the entry and the exit.

“Monforts stenters set the benchmark in terms of energy efficiency and help conserve resources,” says Ahmet Kılıç, founder of Neotek, the representative for Monforts in Turkey. “Automatically setting the initial moisture content requirement for a specific process before drying to a minimum value helps reduce heat evaporation and consequently, energy consumption. The hermetic sealing of the stenter frame further prevents the loss of heated air as well as the ingress of excessive cold air – which has to be heated back up if it is not kept out in the first place.”

The new Montex line was completed at İlay Textile in August 2020, with no problems during either installation or commissioning.

 

Source:

AWOL Media

Oerlikon: Meltblown und Spunbond (c) Oerlikon
19.11.2020

Oerlikon: Meltblown and Spunbond technologies

Since the outbreak of the coronavirus pandemic, the worldwide demand for protective masks and apparel has resulted in a record number of new orders in the high double-digit millions of euros at Oerlikon Nonwoven. The meltblown technology from Neumünster is recognized by the market as being one of the technically most efficient methods for producing highly-separating filter media made from plastic fibers.

Since the outbreak of the coronavirus pandemic, the worldwide demand for protective masks and apparel has resulted in a record number of new orders in the high double-digit millions of euros at Oerlikon Nonwoven. The meltblown technology from Neumünster is recognized by the market as being one of the technically most efficient methods for producing highly-separating filter media made from plastic fibers.

Protective equipment demands high-end nonwoven products
The rising demand for protective masks and other medical protective equipment since the start of the coronavirus pandemic and the associated global ramping up of production capacities has also resulted in an increase in the demand for nonwovens for the production thereof. Initially, this resulted in bottlenecks in the provision of meltblown filter nonwovens. To this end, there had until this point be very few producers of medical filter nonwovens outside China. Meanwhile, the demand for spunbond systems is also rising. “Due to the structure of our group, we are in the fortunate position to swiftly reallocate and free up our production capacities. This means that we are able to relatively quickly deliver not only meltblown systems, but also spunbond equipment”, explains Dr. Ingo Mählmann, Head of Sales & Marketing at Oerlikon Nonwoven, talking about the positive situation at the company.

The capacities for respiratory masks available in Europe to date are predominantly manufactured on Oerlikon Nonwoven systems. “Our machines and systems for manufacturing manmade fiber and nonwovens solutions enjoy an outstanding reputation throughout the world. Ever more manufacturers in the most diverse countries are hoping to become independent of imports”, comments Dr. Mählmann. The Oerlikon Nonwoven meltblown systems are being delivered to Germany, China, Turkey, United Kingdom, South Korea, Italy, France, North America and – for the very first time – to Australia until well into 2021.

Quality and efficiency in demand
Depending on the purpose of the application, medical PPE (personal protection equipment) should be breathable and comfortable to wear, protect medical staff against viruses, bacteria and other harmful substances and form a barrier against liquids. For these reasons, they are often made of either pure spunbond or of spunbond-meltblown combinations. Here, the meltblown nonwoven core assumes the barrier or filter task, while the spunbond has to retain its shape, while being tear-resistant, abrasion-proof, absorbent, particularly flame-resistant and nevertheless extremely soft on the skin.

All masks are not created equal – thanks to the ecuTEC+
Protection against infections such as coronavirus can only be guaranteed with the right quality.

The nonwovens can be electrostatically-charged in order to further improve the filter performance without additionally increasing breathing resistance. Here, Oerlikon Nonwovenʼs patented ecuTEC+ electro-charging unit excels in terms of its extreme flexibility. Nonwovens manufacturers can freely choose between numerous variation options and set the optimal charging method and intensity for their specific applications. In this way, even the smallest particles are still attracted and reliable separated by a relatively open-pored nonwoven. Nevertheless, mask wearers are still able to easily breathe in and out due to the comparatively loose formation of the fibers. To this end, it comes as no surprise that all meltblown systems currently destined for the production of mask nonwovens are equipped with the ecuTEC+ unit.

Relanit 3.2 HS (c) Mayer & Cie
17.11.2020

Mayer & Cie. extends status in Turkey

In pandemic year 2020 circular knitting machine manufacturer Mayer & Cie. (MCT) has further improved its leading position in Turkey. So the country continues to be one of the company’s strongest and most consistent sales markets. Even in difficult years, the manufacturer and its longstanding Turkish representative Mayer Mümessillik have achieved positive results. The reasons for this year’s success, as Mayer & Cie. sees it, are the transfer of production to locations close to Europe, Turkey’s state-of-theart machinery and the increase in demand for comfortable clothing that is suitable as home office wear.

Turkish market is a growth market despite corona setback
“Compared to 2019, we anticipate a growth in the Turkish market even though the corona situation was a serious setback in the second quarter of 2020,” says Stefan Bühler, Mayer & Cie.’s regional sales manager for Turkey.

In pandemic year 2020 circular knitting machine manufacturer Mayer & Cie. (MCT) has further improved its leading position in Turkey. So the country continues to be one of the company’s strongest and most consistent sales markets. Even in difficult years, the manufacturer and its longstanding Turkish representative Mayer Mümessillik have achieved positive results. The reasons for this year’s success, as Mayer & Cie. sees it, are the transfer of production to locations close to Europe, Turkey’s state-of-theart machinery and the increase in demand for comfortable clothing that is suitable as home office wear.

Turkish market is a growth market despite corona setback
“Compared to 2019, we anticipate a growth in the Turkish market even though the corona situation was a serious setback in the second quarter of 2020,” says Stefan Bühler, Mayer & Cie.’s regional sales manager for Turkey.

Mayer & Cie. got off to a strong start on the Bosporus in the first quarter of 2020 with additional positive effects until mid-March. This was due to a desire for production locations close to Europe. In the second quarter, during the lockdown, demand largely ground to a halt. Government measures helped to cushion the downturn. Says Ahmet M. Öğretmen, general manager of MCT’s Turkish sales partner Mayer Mümessillik: “In the second quarter, GDP was down by about 10 percent, so we got off lightly.”

Since July 2020, orders for Mayer & Cie. circular knitting machines have bounced back again. Ahmet M. Öğretmen sees an interplay of reasons for this recovery. The main reason, he says, is the low exchange rate of the Turkish lira, which has boosted exports of ready-made textiles. The Turkish daily Hürriyet reports, with reference to the Turkish state news agency, 11 percent year-on-year growth in August 2020. The most important export markets, the newspaper says, are Germany, the UK and Spain. Between them, they account for around half of exports totalling € 1.27 billion.* “This demand must be fulfilled,” Öğretmen says. “That leads to investment in machinery by manufacturers.”

Relanit is synonymous with single jersey
The machines of choice for Turkish knitwear manufacturers are regularly Mayer & Cie. machines. The long-established German firm’s share of the Turkish market is substantially higher than in other markets. The manufacturer’s position is particularly strong in the market for plain single jersey fabrics, with the Relanit 3.2 HS being the machine of choice. It achieves an extraordinarily high level of productivity, especially in processing elastomer yarns. It also handles a wide range of yarns reliably.

“Interlock is Mayer & Cie.”
Mayer & Cie. is one of the leader in the second major circular knitting discipline, rib and interlock fabrics. The machines used for double jersey fabrics are the OV 3.2 QCe, the D4 2.2 II and the D4 3.2 II. The OV 3.2 QCe knits interlock, 8-lock structures, spacers and fine gauge with 3.2 systems. The D4 2.2 II is another stalwart for rib, 8-lock and interlock. The 8-lock D4 3.2 II is the machine of choice for firms that want to manufacture structures such as Piqué, Punto di Roma or Thermal in addition to interlock.

The MBF 3.2 is another top seller in Turkey. A three-thread fleece machine, it knits fabrics for sportsand leisurewear such as hoodies and is very much in keeping with the trend in home office year 2020. “Comfortable clothing is circular knitted,” says Ahmet M. Öğretmen, “and we benefit from that of course.”

One of the world’s most state-of-the-art machine parks are in Turkey
Another advantage is the modernity of the Turkish machine park, which is doubly attractive in view of Turkey’s weak currency. Says Mayer Mümessillik general manager Öğretmen: “In the past 10 to 20 years there has been very heavy investment in high-quality machines. As a consequence we have the world’s youngest and most up-to-date production facilities.” Combined with geographical proximity to the main export markets in Europe that should prove a growth driver in the years ahead – and keep demand for Mayer & Cie. machines brisk and high.

 

*More informationen here.

Source:

Mayer & Cie GmbH & Co. KG

Monforts texCoat coating system (c) Monforts / AWOL Media
06.10.2020

Monforts at Innovate Textile & Apparel (ITA) 2020

During the Innovate Textile & Apparel (ITA) virtual textile machinery show which will run from October 15th-30th 2020, Monforts will be emphasising its leadership position in three key fields – advanced coating, denim finishing and fabric sanforizing.

With its multi-head capability, the latest Monforts texCoat coating system provides flexibility with an unprecedented range of options and a wide range of modules available.

Refinements
“Since we acquired the coating technology that our systems are based on we have made a lot of refinements and all of them are reflected in higher coating accuracy and the resulting quality of the treated fabrics,” says Monforts Head of Technical Textiles, Jürgen Hanel.
“Our systems have the shortest fabric path from the coating unit into the stenter and we have all variations of coating application systems too – and all of these options are available in wider widths, with the engineering and manufacturing from a single source here in Europe.”

During the Innovate Textile & Apparel (ITA) virtual textile machinery show which will run from October 15th-30th 2020, Monforts will be emphasising its leadership position in three key fields – advanced coating, denim finishing and fabric sanforizing.

With its multi-head capability, the latest Monforts texCoat coating system provides flexibility with an unprecedented range of options and a wide range of modules available.

Refinements
“Since we acquired the coating technology that our systems are based on we have made a lot of refinements and all of them are reflected in higher coating accuracy and the resulting quality of the treated fabrics,” says Monforts Head of Technical Textiles, Jürgen Hanel.
“Our systems have the shortest fabric path from the coating unit into the stenter and we have all variations of coating application systems too – and all of these options are available in wider widths, with the engineering and manufacturing from a single source here in Europe.”

CYD
Denim finishing is meanwhile a field in which Monforts has an undisputed lead and it has been working closely with its many partners in the key denim manufacturing countries of Bangladesh, Brazil, China, India, Mexico Pakistan and Turkey to develop advanced solutions. The latest of these is the CYD yarn dyeing system.
“CYD is based on the proven Econtrol® dyeing system for fabrics*,” explains Monforts Head of Denim Hans Wroblowski. “It integrates new functions and processes into the weaving preparatory processes – spinning, direct beaming, warping and assembly beaming, followed by sizing and dyeing – in order to increase quality, flexibility, economic viability and productivity. The CYD system has been developed in response to a very strong market demand.”

Pre-shrinking
Monforts has also recently delivered a significant number of its latest Monfortex sanforizing lines to customers around the world.
Sanforizing is vital to final fabric quality, pre-shrinking it by compressing prior to washing, to limit any residual or further shrinkage in a made-up finished garment to less than 1%, for perfect comfort and fit over an extended lifetime.

As with industry-leading Montex stenters, Monfortex lines benefit from the latest Qualitex 800 control system which allows all parameters to be easily automated via the 24-inch colour touchscreen, including production speed, control of all fabric feed devices, rotation spray or steaming cylinder options, the width of the stretching field and the rubber belt pressure. Up to 10,000 separate process parameter records can be generated and stored by the data manager.

 

*Econtrol® is a registered mark of DyStar Colours Distribution GmbH, Germany.

Baldwin installs six precision spray systems in 60 days for textile manufacturers (c) Baldwin Technology Company Inc.
Baldwin’s TexCoat G4 precision spray system produces ideal results in fabric finishing, because the exact required amount of water and chemistry is always applied.
22.09.2020

Baldwin: six precision spray systems in 60 days for textile manufacturers

  • Fabric finishing and sanforization systems installed in the US and Turkey to enhance productivity

ST. LOUIS - Baldwin Technology Company Inc. has successfully installed six new fabric finishing and sanforizing precision spray systems in the US and Turkey. Despite the COVID-19 pandemic, the installations were completed in just 60 days, thanks to close collaboration between onsite Baldwin textile team members, local agents and remote support from the company’s product and technology center in Sweden.
For textiles, non-wovens and technical textiles, Baldwin’s precision spray technology processes a wide range of low-viscosity water-based chemicals, such as softeners, anti-microbial agents, water repellents, oil  repellents, flame retardants and more.

  • Fabric finishing and sanforization systems installed in the US and Turkey to enhance productivity

ST. LOUIS - Baldwin Technology Company Inc. has successfully installed six new fabric finishing and sanforizing precision spray systems in the US and Turkey. Despite the COVID-19 pandemic, the installations were completed in just 60 days, thanks to close collaboration between onsite Baldwin textile team members, local agents and remote support from the company’s product and technology center in Sweden.
For textiles, non-wovens and technical textiles, Baldwin’s precision spray technology processes a wide range of low-viscosity water-based chemicals, such as softeners, anti-microbial agents, water repellents, oil  repellents, flame retardants and more.

These systems enable fabric producers to significantly reduce chemical and water consumption, while speeding up production times and eliminating production steps, including drying and bath changeovers when switching fabric colors. “Our customers are major manufacturers in fabric dying, finishing and remoistening, and we want to provide outstanding service and support—even in times like this,” said Rick Stanford, Business Development Leader at Baldwin and the commercial leader of the US installations. “Not only does our precision spray technology enhance productivity in their process, but there is also zero waste, which goes hand-in-hand with the increased sustainability focus in the textile industry.”

In North Carolina, two new TexCoat G4 precision spray systems are now in production with major international vertical manufacturers of outdoor living, performance fabrics and automotive fabrics. In Georgia, a major vertical manufacturer of workwear and protective fabrics installed a sanfor precision spray system, which has helped the customer obtain deeper penetration of moisture into fabrics treated with durable water repellents. In Turkey, three new TexCoat G4 systems were installed in Çorlu, northwest of Istanbul, for a large producer of knit fabrics, such as T-shirts. “In Turkey, the manufacturer purchased and installed one TexCoat G4 system before COVID-19, and the customer was so pleased with the results that, during the pandemic, three more were purchased,” said Simone Morellini, Sales Manager- EMEAR at Baldwin and the commercial leader of the Turkish installations. “The systems were manufactured and installed during the lockdown, and now, all four systems are up and running, and being used heavily on a daily basis.” “With the success we have seen, we plan to apply the same strategies for upcoming installations, including the next one in Honduras: strong local management and customer coordination, combined with  effective remote support during the installation,” said Stanford.

Source:

Baldwin Technology Company Inc.

Oerlikon Nonwoven meltblown technology meanwhile in demand across the globe (c) Oerlikon
Daniel Günther (2nd from left), Schleswig-Holstein’s Minister President, together with Rainer Straub, Head of Oerlikon Nonwoven, Matthias Pilz, Head of Oerlikon Neumag, and Matthias Wäsch, Chairman of the Works Council, at the tour of the Neumünster site where the Oerlikon Nonwoven meltblown technology – currently in huge demand across the globe – is manufactured.
08.07.2020

Oerlikon Nonwoven meltblown technology meanwhile in demand across the globe

  • Schleswig-Holstein Minister President visits Neumünster, Germany


Since the outbreak of the coronavirus pandemic, the worldwide demand for protective masks and apparel has resulted in a record number of new orders in the high double-digit millions of euros at the Oerlikon Nonwoven business unit of the Swiss Oerlikon Group. From the manufacturing site in Neumünster, Germany, the high-tech meltblown systems – with their patented ecuTE+ nonwovens electro-charging technology – are meanwhile be exported all over the world. For the very first time, a contract has now been signed with a business in Australia. Today, Schleswig-Holstein’s Minister President Daniel Günther was won over on site by the technology of a ‘global player’. Rainer Straub, Head of Oerlikon Nonwoven, was thrilled, stating: “The machines and systems for manufacturing manmade fiber and nonwovens solutions from Neumünster enjoy an outstanding reputation throughout the world. It is especially in this crisis that the technology from Schleswig-Holstein has proven itself to be absolutely world-class.”

  • Schleswig-Holstein Minister President visits Neumünster, Germany


Since the outbreak of the coronavirus pandemic, the worldwide demand for protective masks and apparel has resulted in a record number of new orders in the high double-digit millions of euros at the Oerlikon Nonwoven business unit of the Swiss Oerlikon Group. From the manufacturing site in Neumünster, Germany, the high-tech meltblown systems – with their patented ecuTE+ nonwovens electro-charging technology – are meanwhile be exported all over the world. For the very first time, a contract has now been signed with a business in Australia. Today, Schleswig-Holstein’s Minister President Daniel Günther was won over on site by the technology of a ‘global player’. Rainer Straub, Head of Oerlikon Nonwoven, was thrilled, stating: “The machines and systems for manufacturing manmade fiber and nonwovens solutions from Neumünster enjoy an outstanding reputation throughout the world. It is especially in this crisis that the technology from Schleswig-Holstein has proven itself to be absolutely world-class.”

In addition to a tour of the meltblown system and its assembly and production facilities, the visit by Minister President Daniel Günther had one purpose above all: the dialog between politicians and business. Rainer Straub, Head of Oerlikon Nonwoven, and Matthias Pilz, Head of Oerlikon Neumag, jointly expressed their thanks for the support that Oerlikon has repeatedly had the fortune to experience over the past months and years in Schleswig-Holstein and looked to the future full of hope. “As a result of our additional investment at the site here in Neumünster – be this in our new technology center that will be completed by the end of this year or in our new logistics center that is already operating – we, as one of the region’s largest employers, are continuing to move forward, supported by a State Government that is also focusing on both promoting industry and business and on advancing an efficient training and educational system, as innovation is only possible with outstanding engineers”, stated Matthias Pilz. And Rainer Straub directed his appeal specifically at the Minister President: “Treat education and training as a priority. Ultimately, they will secure the future of Schleswig-Holstein as a center of excellence and manufacturing!”

Five-million-euro digitalization program

Daniel Günther, the incumbent Minister President of Schleswig-Holstein since 2017, immediately responded, making reference to one of the Federal State’s current training initiatives: “The State Government is supporting higher education institutions and students in the present coronavirus crisis. With a five-million-euro digitalization program, we are investing on the long-term digitalization of our higher education institutions. With this, we are overall creating a future for young people, particularly also for those who could very well go on to invent the next generation of manmade fiber systems.” And the Minister President was just as impressed by the willingness and readiness with which Oerlikon has been providing high-level support since the beginning of the COVID-19 pandemic to master the present challenges as he was with the company’s meltblown technology itself. Rainer Straub explained: “When, at the beginning of the pandemic in February, demand for protective face masks increased rapidly, we at Oerlikon Nonwoven responded immediately. We ramped up all the available production capacities here in Neumünster in order to quickly manufacture nonwovens for producing face masks using our laboratory systems. As a result, we have been able to make a small, regional contribution to covering demand. In parallel, we have pulled out all the stops in order to systematically further expand our skills as machine and system builders so as to cater to the initially expected, and now also continuing, global demand for meltblown systems as quickly as possible.”

Leading meltblown technology

The Oerlikon Nonwoven meltblown technology – with which nonwovens for protective masks can also be manufactured, among other things – is recognized by the market as being the technically most efficient method for producing highly-separating filter media made from plastic fibers. The capacities for respiratory masks available in Europe to date are predominantly manufactured on Oerlikon Nonwoven systems. “Ever more manufacturers in the most diverse countries are hoping to become independent of imports. Therefore, what we are experiencing in Germany is also happening in both industrialized and emerging countries throughout the world”, commented Rainer Straub. In addition to China, Turkey, the United Kingdom, South Korea, Austria and numerous countries in both North and South America, Australia and not least Germany will for the first time also be among the countries to which Oerlikon Nonwoven will be delivering machines and equipment before the end of 2021.

President of Indonesia Inaugurates Country’s Largest Viscose Rayon Facility (c) APR
President of Indonesia Inaugurates Country’s Largest Viscose Rayon Facility
21.02.2020

APR: New Viscose Rayon Facility

  • Investment of Rp. 15 trillion (USD1,1 billion) in facility
  • Supports development of national textile industry and ‘Making Indonesia 4.0’ roadmap

The President of Indonesia, Joko Widodo, today inaugurated Indonesia's largest integrated viscose rayon production facility, injecting a boost for the country’s textile sector and the Indonesian Government’s industrial 4.0 development strategy.

The new Asia Pacific Rayon (APR) facility is located in the same production complex as APRIL Group in Pangkalan Kerinci, Riau province, Sumatra. This co-location allows integrated operations where renewable plantation pulp supply from APRIL feeds directly to APR for viscose rayon production. The new operation represents a total investment of approximately Rp.15 trillion (USD1.1 billion).

The APR facility has an annual production capacity of 240,000 tons. The inauguration ceremony included the signing of a plaque by President Widodo and the symbolic sealing by the President of an export container with 10,190 tons of viscose rayon fibre for shipment to Turkey, one of APR’s key export markets, and another 12,000 tons to Central Java.

  • Investment of Rp. 15 trillion (USD1,1 billion) in facility
  • Supports development of national textile industry and ‘Making Indonesia 4.0’ roadmap

The President of Indonesia, Joko Widodo, today inaugurated Indonesia's largest integrated viscose rayon production facility, injecting a boost for the country’s textile sector and the Indonesian Government’s industrial 4.0 development strategy.

The new Asia Pacific Rayon (APR) facility is located in the same production complex as APRIL Group in Pangkalan Kerinci, Riau province, Sumatra. This co-location allows integrated operations where renewable plantation pulp supply from APRIL feeds directly to APR for viscose rayon production. The new operation represents a total investment of approximately Rp.15 trillion (USD1.1 billion).

The APR facility has an annual production capacity of 240,000 tons. The inauguration ceremony included the signing of a plaque by President Widodo and the symbolic sealing by the President of an export container with 10,190 tons of viscose rayon fibre for shipment to Turkey, one of APR’s key export markets, and another 12,000 tons to Central Java.

The ceremony was also graced by the Minister of Industry, Agus Gumiwang Kartasasmita, the Minister of Trade Agus Suparmanto, the Governor of Riau, Syamsuar, RGE Founder and Chairman Sukanto Tanoto, and Anderson Tanoto, Director, RGE.

Speaking at the inauguration, President Widodo welcomed APR's investment in the development of the national textile industry. The role of the private sector was influential in driving economic growth, alongside the stimulus provided by the Government, he said. “Our garment industry should be greater than Vietnam. We already have our own raw materials here, such as viscose rayon, to support the industry,” he said.

Economic Contribution
APR’s business aligns with President Jokowi's vision to encourage more value-added investment in the nation and the strengthening of the national textile and textile product (TPT) industry, as set out in the Making Indonesia 4.0 Road map. In addition, the production of viscose rayon will reduce dependence on the import of textile raw materials, particularly cotton, to meet domestic demand.

Agus Gumiwang Kartasasmita, Minister for Industry, said: “By optimising the availability and use of raw materials originating from Indonesia, we can boost the performance of our textile sector. This is just one of several steps we are taking to continue to improve the performance and competitiveness of the labour-intensive industry.”

Basrie Kamba, Director APR, said: “The presence of APR will have a positive impact on employment and business opportunities for small and medium-sized businesses in the upstream and downstream sectors of the textiles and textile products industry. We are honoured and grateful to President Jokowi for inaugurating our new facility”.

In addition to Turkey, APR’s products are exported to 14 other countries including key textile centres such as Pakistan, Bangladesh, Vietnam, Brazil, and various parts of Europe. The products also support an expanding Indonesia fashion industry.

It is estimated that APR may generate foreign exchange revenues exceeding Rp1.77 trillion (USD130 million) annually, and reduce dependence on imported raw materials by about Rp2.01 trillion (USD149 million) annually.

Sustainable Production
APR produces sustainable viscose rayon fiber from renewable, traceable and biodegradable raw materials. The company’s raw materials are supplied by APRIL Group, which is recognised as a responsible pulp producer through national (Timber Legality Verification System) and international (Program for the Endorsement of Forest Certification/PEFC) certifications.

APR is the first viscose rayon manufacturer in Indonesia to receive the internationally recognised STeP certification from OEKO-TEX ®, an independent Swiss-based certification organisation, for the responsible manufacturing of viscose staple fibre.

APR has launched the ‘Everything Indonesia’ campaign to promote the sustainable sourcing and production of fashion from Indonesia. The aim is to support Indonesia’s resurgence as a global centre for textile manufacturing, and catalyse home-grown fashion design and creativity.

Source:

Omnicom Public Relations Group

Oerlikon feiert vier Weltpremieren zur ITMA Barcelona 2019 (c) Oerlikon
Oerlikon Shuttle ITMA 2019
08.05.2019

Oerlikon celebrates four world premieres at ITMA Barcelona 2019

  • Clean Technology. Smart Factory.

Remscheid – Oerlikon invites all visitors to this year's ITMA in Barcelona on a journey into the future of manmade fiber production. From 20 to 26 June 2019, the world market leader will show all its guests its vision of a sustainable and automated manmade fiber production in a virtual 4D showroom at its 1,000 m² stand in Hall 7, A101: "Clean Technology. Smart Factory." is the motto of the future. And this is only a stone's throw away from reality at the stand. Because today Oerlikon is presenting four world premieres for efficient machine and plant concepts in a new, innovative industrial design. Together with numerous other innovations, all this forms the new DNA of the Oerlikon Manmade Fibers segment.

The challenges for the manmade fiber industry are manifold and Oerlikon shows its customers solutions:

  • Clean Technology. Smart Factory.

Remscheid – Oerlikon invites all visitors to this year's ITMA in Barcelona on a journey into the future of manmade fiber production. From 20 to 26 June 2019, the world market leader will show all its guests its vision of a sustainable and automated manmade fiber production in a virtual 4D showroom at its 1,000 m² stand in Hall 7, A101: "Clean Technology. Smart Factory." is the motto of the future. And this is only a stone's throw away from reality at the stand. Because today Oerlikon is presenting four world premieres for efficient machine and plant concepts in a new, innovative industrial design. Together with numerous other innovations, all this forms the new DNA of the Oerlikon Manmade Fibers segment.

The challenges for the manmade fiber industry are manifold and Oerlikon shows its customers solutions:

1. Choosing the right business model
Price pressure on fiber and yarn manufacturers is growing due to global market consolidation. Here it is important to position oneself correctly. Are you producing polyester, nylon or polypropylene for the niche market and skimming off good margins with innovative products and ingenious material properties, or are you looking for business success through economies of scale in the volume market such as the constantly growing apparel sector? Oerlikon has the right answers for both business models. And the most important thing: the market leader supplies all solutions from a single source. See for yourself at the world premieres of the machine and system concepts of WINGS FDY PA6, BCF S8 Tricolor and the revolutionary eAFK Evo texturing machine.

2. Finding alternatives for good personnel
Finding good operators in the manmade fiber industry is becoming increasingly difficult, even in emerging industrial nations such as China, India and Turkey. The solution is obvious. What, for example, the automotive industry achieved years ago with the 3rd Industrial Revolution is now also taking its course in the textile industry. And at the same time it is even shifting up a gear. In the next step, automation in combination with digitization will lead to new, sustainable production. Oerlikon will be showing how automation and digitization interact at ITMA. Self-learning machines and systems, artificial intelligence (AI), remote services and edge computing are just a few of the key words in the digital half of the new Oerlikon Manmade Fibers DNA.

3. Guarantee quality and traceability
The qualities of the fibers and yarns must meet the highest demands and their production must be traceable throughout the textile value chain. This no longer only plays an important role in the automotive industry, where safety is of paramount importance. Other branches of industry that use fibers, yarns and nonwovens also want to know where the raw materials they produce for consumer articles come from. Legal regulations are demanding this more and more frequently. Oerlikon offers optimal solutions with its DIN ISO certified manufacturing processes. More than half of the world's manmade fiber producers are convinced every day that the qualities produced on Oerlikon Barmag, Oerlikon Neumag and Oerlikon Nonwoven equipment are right – and all visitors to ITMA can do the same on site.

4. Efficient and sustainable production
In the future, the materials produced from manmade fibers must become part of a further improved global recycling economy. The recycling of polyester – with over 80% market share the most frequently used manmade fiber in the world – has not only been on the agenda since today. Oerlikon already has solutions at hand: from PET bottles to fibers and filaments, to textiles and carpets. ITMA is the next step. With the VacuFil® Oerlikon in cooperation with the subsidiary company BBEngineering presents the world premiere No. 4 – a recycling solution within a running polyester production with a waste-free approach.

Vision becomes reality
The Oerlikon Manmade Fibers segment thus demonstrates what the ITMA in Barcelona promises as the world's leading trade fair for textile machinery and plant construction: "Innovating the world of textiles – sourcing for a sustainable future". In Hall 7, A101, this is already reality.

More information:
ITMA Oerlikon Fibers Automation
Source:

Oerlikon

28.08.2018

480 international exhibitors ready for Cinte Techtextil 2018

Cinte Techtextil China opens its doors next week, with around 480 exhibitors from 22 countries and regions preparing for another successful showcase of the world’s leading textile innovations. Leading international and domestic brands will feature in halls N1 – N3 at Shanghai New International Expo Centre from 4 – 6 September, making Cinte Techtextil the ideal place to make connections and gain insight into Chinese and Asian market trends.

The technical textile industry in the Asia region, and China in particular, has been growing steadily and is predicted to continue doing so. China’s total output of technical textiles and nonwoven products is estimated to account for 30% of global production by 2020, and double that of 2013. This high potential for growth, achieved through investments worth billions of dollars, has drawn attention from European exhibitors, who are set to travel to the region for Cinte Techtextil.

Cinte Techtextil China opens its doors next week, with around 480 exhibitors from 22 countries and regions preparing for another successful showcase of the world’s leading textile innovations. Leading international and domestic brands will feature in halls N1 – N3 at Shanghai New International Expo Centre from 4 – 6 September, making Cinte Techtextil the ideal place to make connections and gain insight into Chinese and Asian market trends.

The technical textile industry in the Asia region, and China in particular, has been growing steadily and is predicted to continue doing so. China’s total output of technical textiles and nonwoven products is estimated to account for 30% of global production by 2020, and double that of 2013. This high potential for growth, achieved through investments worth billions of dollars, has drawn attention from European exhibitors, who are set to travel to the region for Cinte Techtextil.

This year’s European Zone will feature around 30 exhibitors from countries including Austria, France, the Netherlands, Sweden, Switzerland and the UK, while further exhibitors can be found in national pavilions from Belgium, Germany and Italy. In addition to this, the Czech Republic will present its debut pavilion, showcasing exhibitors with solutions for technical yarn, fabric processing and nonwoven fabrics.

In addition to this, exhibitors from 12 more countries and regions will present their latest innovations to the market. These include domestic and international exhibitors from China, Hong Kong, India, Indonesia, Israel, Japan, Korea, Saudi Arabia, Taiwan, Thailand, Turkey and the US.

Belt and Road: a success story for Buildtech
Following higher regulations and quality standards that aim to exceed Western levels, demand is high in China for production machinery. What’s more, with the national nonwovens market displaying particularly fast growth, Cinte Techtextil has attracted some of the world’s leading nonwoven and weaving machinery brands.

The fair will showcase leading global exhibitors across 12 application areas. Two areas to watch out for include Buildtech and Mobiltech, which are both performing well in Asia and specifically in China. The Belt and Road initiative brings Buildtech a great deal of benefits through China’s enormous investments in global infrastructure. Adding to this, China’s automobile production has been increasing 3% year-on-year, with particularly high growth seen in new-energy vehicles, SUVs and commercial vehicles. China has become the world’s largest auto producer, and this has been boosting progress in the Mobiltech category.

Cinte Techtextil fringe programme a hub of industry insight
A comprehensive fringe programme will keep Cinte Techtextil fairgoers up to date with industry news, with standout events including the 7th China International Nonwovens Conference. Focusing on the global nonwovens industry, topic highlights include the latest innovations in China’s nonwovens industry, an insight into the North American nonwovens market, future trends in the global hygiene product market, and more. The conference will also discuss innovations and developments in filter materials and the wipe industry.

The first day of the fringe programme will see a panel discussion in hall N1, moderated by the Taiwan Technical Textiles Association (TTTA), with confirmed panellists including DuPont, IBENA Textilwerke and SGS-CSTC Standards Technical Services. The panel will focus on current trends, developments and standards in the protective textile industry.

Other fringe programme events will include seminars and product presentations led by industry leaders on the latest global technologies and market trends, and an Innovation Showcase Area in a variety of application categories. 

More information:
Cinte Techtextil China
Source:

Messe Frankfurt (HK) Ltd