From the Sector

Reset
10 results
Gerhard Lettl (AVK Board Member, C.F. Maier Europlast GmbH & Co. KG), Felix Pohlmeyer (ITA), Prof. Dr Jens Ridzewski (AVK Board Member, IMA Materialforschung und Anwendungstechnik GmbH), Tim Röding (ITA), from left to right © AVK
Gerhard Lettl (AVK Board Member, C.F. Maier Europlast GmbH & Co. KG), Felix Pohlmeyer (ITA), Prof. Dr Jens Ridzewski (AVK Board Member, IMA Materialforschung und Anwendungstechnik GmbH), Tim Röding (ITA), from left to right
23.11.2023

CarboScreen: Sensor monitoring for complex carbon fibre production

Felix Pohlkemper and Tim Röding from Institut für Textiltechnik (ITA) of RWTH Aachen University are developing a technology with their start-up CarboScreen GmbH that makes complex carbon fibre production controllable through sensor monitoring. With the help of CarboScreen technology, it should be possible to double the production speed from the current 15 m/min to 30 m/min in the medium term. The doubling of production speed alone could result in an increase in turnover of up to €37.5 million per year and production plant. Felix Pohlkemper and Tim Röding were awarded third place in the AVK Innovation Award 2023 in the Processes and Procedures category for this ground-breaking development. The award ceremony took place during the JEC Roof Forum in Salzburg, Austria.

Felix Pohlkemper and Tim Röding from Institut für Textiltechnik (ITA) of RWTH Aachen University are developing a technology with their start-up CarboScreen GmbH that makes complex carbon fibre production controllable through sensor monitoring. With the help of CarboScreen technology, it should be possible to double the production speed from the current 15 m/min to 30 m/min in the medium term. The doubling of production speed alone could result in an increase in turnover of up to €37.5 million per year and production plant. Felix Pohlkemper and Tim Röding were awarded third place in the AVK Innovation Award 2023 in the Processes and Procedures category for this ground-breaking development. The award ceremony took place during the JEC Roof Forum in Salzburg, Austria.

The production of carbon fibres is highly complex. In the current state of the art, however, the manufacturing process is only monitored manually by semi-skilled workers. However, even minimal fibre damage during production leads to a reduction in the quality of the carbon fibre. In extreme cases, it can also lead to plant fires. To ensure production quality, the production speed is currently limited to a maximum of 15 m/min. In fact, the production speed of the systems could be higher. The sensor-based online monitoring of Carbo-Screen makes it possible to increase the production speed to 30 m/min in the medium term. As a result of the increased production volume per system, the specific production costs of the carbon fibre are reduced, which can result in lower prices.

A reduced sales price would make it possible to use carbon fibres and their composite materials even more widely in traditional markets such as aerospace technology and wind energy, as well as for mass production in the automotive industry.

The CarboScreen online monitoring system is currently being developed for industrial use. It is to be validated at an industrial plant in 2024. CarboScreen GmbH was founded as part of EXIST funding and offers AI-supported sensor systems for carbon fibre production. The sensor technology continuously monitors the fibre throughout the entire production process. Deviations are detected automatically.

The winners of the AVK Innovation Award are honoured annually by the AVK Industrievereinigung Verstärkte Kunststoffe. Companies, institutes and their partners are honoured in three categories: products and applications, processes and procedures, and research and science.

Dr Ioana Slabu and Benedict Bauer with the nanomodified stent. Photo Peter Winandy
30.03.2023

Nanomodified polymerstent: Novel technology for tumour therapy

  • Electromagnetically heatable nanomodified stent for the treatment of hollow organ tumours wins second place at the RWTH Innovation Award

Almost every fourth person who dies of cancer has a hollow organ tumour, for example in the bile duct or in the oesophagus. Such a tumour cannot usually be removed surgically. It is only possible to open the hollow organ for a short time using a stent, i.e. a tubeshaped prosthesis. However, the tumour grows back and penetrates the hollow organ through the stent. Ioana Slabu from the Institute of Applied Medical Technology and Benedict Bauer from the Institut für Textiltechnik of RWTH Aachen University have now developed a novel technology for the therapy of hollow organ tumours, which was awarded second place in the RWTH Innovation Award. This involves a polymerstent that contains magnetic nanoparticles. When electromagnetic fields are applied, these nanoparticles lead to a controlled heating of the stent material and thus of the tumour. Because the tumour reacts much more sensitively to heat than healthy tissue, it is destroyed and the hollow organ remains open. Thus, the stent develops a self-cleaning effect.  

  • Electromagnetically heatable nanomodified stent for the treatment of hollow organ tumours wins second place at the RWTH Innovation Award

Almost every fourth person who dies of cancer has a hollow organ tumour, for example in the bile duct or in the oesophagus. Such a tumour cannot usually be removed surgically. It is only possible to open the hollow organ for a short time using a stent, i.e. a tubeshaped prosthesis. However, the tumour grows back and penetrates the hollow organ through the stent. Ioana Slabu from the Institute of Applied Medical Technology and Benedict Bauer from the Institut für Textiltechnik of RWTH Aachen University have now developed a novel technology for the therapy of hollow organ tumours, which was awarded second place in the RWTH Innovation Award. This involves a polymerstent that contains magnetic nanoparticles. When electromagnetic fields are applied, these nanoparticles lead to a controlled heating of the stent material and thus of the tumour. Because the tumour reacts much more sensitively to heat than healthy tissue, it is destroyed and the hollow organ remains open. Thus, the stent develops a self-cleaning effect.  

Ioana Slabu of the AME explains: "Not only can we drastically reduce treatment costs, but above all we can provide relief for millions of patients worldwide.
 
A manufacturing process and proof of concept for magnetic hyperthermia are already in place. This novel technology has a very high development potential because it can also be used for tumours in other parts of the body such as the prostate, stomach, intestine or urinary bladder or for cardiovascular diseases.  

The AiF/IGF project started under the project title "ProNano" funded by BMWK. Now the approval for the follow-up project "ProNano2" has also been received. The approved project is called: "Validation of the innovation potential of heatable stents for heat-induced treatment of cavity tumours" and is funded by BMBF in course of the VIP+ program. With the Clinic for General, Visceral and Transplantation Surgery of the University Hospital Aachen and the Institute for Technology and Innovation Management at RWTH Aachen University, the consortium is enriched by clinical and economic expertise. Every year, RWTH Aachen University honours particularly innovative university projects with the Innovation Award. Professor Malte Brettel, Prorector for Business and Industry, presented the certificates to four outstanding projects as part of RWTHtransparent.

Source:

ITA – Institut für Textiltechnik of RWTH Aachen University

(c) Digital Capability Center
15.03.2023

ITA Supports SMEs in Digitisation and Sustainability

The Institut für Textiltechnik (ITA) of RWTH Aachen University, as part of the Mittelstandzentrum 4.0 Kompetenzzentrum Textil vernetzt, has supported numerous small and medium-sized enterprises (SMEs) on their way to digitalisation over the last five years. At the Digital Capability Center (DCC) in Aachen, for example, SMEs were able to experience digitised production from yarn to smart bracelets and thus test the feasibility of Industry 4.0 solutions in their working environment.

New supply chain laws and social sustainability now pose current challenges for SMEs. In the follow-up project Mittelstand-Digital Zentrum Smarte Kreisläufe (SME Digital Centre Smart Cycles), ITA will be supporting SMEs from 1 March in implementing ideas for digitalisation and sustainability in concrete terms.

The Institut für Textiltechnik (ITA) of RWTH Aachen University, as part of the Mittelstandzentrum 4.0 Kompetenzzentrum Textil vernetzt, has supported numerous small and medium-sized enterprises (SMEs) on their way to digitalisation over the last five years. At the Digital Capability Center (DCC) in Aachen, for example, SMEs were able to experience digitised production from yarn to smart bracelets and thus test the feasibility of Industry 4.0 solutions in their working environment.

New supply chain laws and social sustainability now pose current challenges for SMEs. In the follow-up project Mittelstand-Digital Zentrum Smarte Kreisläufe (SME Digital Centre Smart Cycles), ITA will be supporting SMEs from 1 March in implementing ideas for digitalisation and sustainability in concrete terms.

This means finding sustainable solutions and processes for the circular economy together with companies and developing new digital business models. The ITA's solutions cover the areas of awareness-raising, qualification, implementation and networking. These offers are free of charge for SMEs - follow-up projects often lead to the funding programme "Central Innovation Programme for SMEs - ZIM" of the Federal Ministry of Economics and Climate Protection (BMWK) or to research and development projects.

Questions concerning the funding conditions can be sent to the following e-mail address: rosario.othen@ita.rwth-aachen.de.

Source:

Institut für Textiltechnik der RWTH Aachen University

(c) ITA
16.12.2021

International Sustainable Aviation and Energy Society Award for Professor Thomas Gries

On 27 November 2021, the Scientific Award for International Sustainable Aviation and Energy Society (SARES Award) was awarded to Professor Dr Thomas Gries from the Institut für Textiltechnik of RWTH Aachen University. The award ceremony took place during the closing ceremony of the International Symposium on Sustainable Aviation (ISSA) in a hybrid format online and simultaneously at Kasetsart University, Bangkok, Thailand.
 
With the award, the committee recognised the ongoing contribution of Pro-fessor Gries and the Institut für Textiltechnik to the digitisation and bio-transformation of the textile sector, as well as the Institute as a place of innovation for sustainable aviation.

On 27 November 2021, the Scientific Award for International Sustainable Aviation and Energy Society (SARES Award) was awarded to Professor Dr Thomas Gries from the Institut für Textiltechnik of RWTH Aachen University. The award ceremony took place during the closing ceremony of the International Symposium on Sustainable Aviation (ISSA) in a hybrid format online and simultaneously at Kasetsart University, Bangkok, Thailand.
 
With the award, the committee recognised the ongoing contribution of Pro-fessor Gries and the Institut für Textiltechnik to the digitisation and bio-transformation of the textile sector, as well as the Institute as a place of innovation for sustainable aviation.

Examples of this include the development of 3D braided ceramic matrix composite components for aircraft engines, which were researched together with partners in a Horizon 2020 project (EU project AllOxITD). The ongoing Chrysomallos research project as another example, funded under the national aeronautics research programme in Germany, aims to develop a completely new and sustainable high-performance insulator for aircraft cabins based on aerogels. These have a significantly lower weight than the glass fibre mats used up to now, while providing the same insulation performance, and solve the problem of the previously high manufacturing costs of aerogels. The aim of the project is to develop an insulation material with reduced density (reduction of more than 20 percent). To this end, a new type of insulation material based on aerogel is to be developed. The basis is an aerogel fleece (0.06 W/mK at 28 kg/m³), which has already been developed as part of a dissertation at the Institut für Textiltechnik of RWTH Aachen University (Mroszczok, J.: 2019).

The aviation industry is one of the fastest growing industries in the world. Due to this fact and its importance for society and the global economy, it needs to make special efforts towards sustainability. The ISSA, an international multi-disciplinary symposium, aims to address current issues in aviation such as improving aircraft fuel efficiency, promoting the use of biofuels, minimising environmental impact, mitigating greenhouse gas emissions and reducing engine and aircraft noise. ^

Through the award, SARES honours scientists and researchers whose work on sustainable aviation issues has made an important contribution at the international level. The selection is based on the scientific publications of the applicant or nominee, the h-index, i.e. the key figure for the worldwide perception of a scientist in professional circles, the project topics and the project results.

New Opportunities for Cellulose Fibres in Replacing Plastics (c) nova-Institut
Nicolas Hark - nova-Institut (DE)
08.12.2021

New Opportunities for Cellulose Fibres in Replacing Plastics

  • Second Session of the International Conference on Cellulose Fibres 2022

Cellulose fibers are a true material miracle as they offer a steadily expanding, broad range of applications. Meanwhile markets are driven by technological developments and policy frameworks, especially bans and restrictions on plastics, as well as an increasing number of sustainability requirements. The  presentations will provide valuable information on the various use-opportunities for cellulosic fibers through a policy overview, a special session on sustainability, recycling and alternative feedstocks, as well as the latest developments in pulp, cellulosic fibers and yarns. In addition, examples of non-wovens, packaging and composites will offer a look beyond the horizon of conventional application fields.

  • Second Session of the International Conference on Cellulose Fibres 2022

Cellulose fibers are a true material miracle as they offer a steadily expanding, broad range of applications. Meanwhile markets are driven by technological developments and policy frameworks, especially bans and restrictions on plastics, as well as an increasing number of sustainability requirements. The  presentations will provide valuable information on the various use-opportunities for cellulosic fibers through a policy overview, a special session on sustainability, recycling and alternative feedstocks, as well as the latest developments in pulp, cellulosic fibers and yarns. In addition, examples of non-wovens, packaging and composites will offer a look beyond the horizon of conventional application fields.

The second session of the conference: "New Opportunities for Cellulose Fibres in Replacing Plastics", will focus on questions such as: "What is the impact of the ban on plastics on single-use products?" and "What are the latest regulatory issues and policy opportunities for cellulose fibres?".  This section presents new opportunities for replacing fossil-based insulating materials with cellulose-based technologies that can be used for a variety of applications, from aerospace to mobility, as well as in construction. For the program just click here.

Speakers of the Session "New Opportunities for Cellulose Fibres in Replacing Plastics":

  • Nicolas Hark - nova-Institut (DE): Opportunities in Policy for Cellulose Fibres
  • Paula Martirez - Stora Enso (SE): Last years Winner Papira® – an Eco-revolution in Foam Packaging
  • Stefanie Schlager - Lenzing (AT): LENZING™ Fibres for Sustainable Single use Products
  • Sascha Schriever - Institut für Textiltechnik der RWTH Aachen University (DE): Cellulose Aerogel Non-wovens – Sustainable Insulators of Tomorrow
(c) Kai-Chieh Kuo
17.11.2021

ITA PhD student Kai-Chieh Kuo was awarded Best Master’s Thesis Award of Walter Reiners-Stiftung

Kai-Chieh Kuo, PhD student at the Institut für Textiltechnik (ITA) of RWTH Aachen University, was awarded the German Textile Mechanical Engineering 2021 Best Master's Thesis Award for his master's thesis entitled "Modification of the tube weaving process of fine yarns for the production of woven ultra-low profile stent grafts". The prize is endowed with 3,500€. Peter D. Dornier, Chairman of the Board of the Walter Reiners-Stiftung (Foundation), virtually presented the award on the occasion of the ADD International Textile Conference on 9 November 2021.

Kai-Chieh Kuo, PhD student at the Institut für Textiltechnik (ITA) of RWTH Aachen University, was awarded the German Textile Mechanical Engineering 2021 Best Master's Thesis Award for his master's thesis entitled "Modification of the tube weaving process of fine yarns for the production of woven ultra-low profile stent grafts". The prize is endowed with 3,500€. Peter D. Dornier, Chairman of the Board of the Walter Reiners-Stiftung (Foundation), virtually presented the award on the occasion of the ADD International Textile Conference on 9 November 2021.

Minimally invasive endovascular aortic repair (EVAR) with textile stent-graft systems is nowadays a clinically established therapy procedure for the treatment of abdominal aortic aneurysms (AAA) – pathological bulges of the aorta. Due to the thick profile of the folded stent graft systems, there is currently a high risk of injuring narrowed or highly angulated access vessels from the inside during implantation. Stent graft systems with smaller profiles could provide an improvement, which could overcome complicated access routes through a lower bending stiffness. One possible approach for reducing the system profiles is the use of thin-walled tubular woven fabrics made of ultrafine multifilament yarns (≤20 dtex) as graft material.

Up to now, it has not been possible to process the fine yarns with the required high thread density (>200 threads/cm) and the available weaving technology in order to guarantee sufficient tightness against blood.

In his master's thesis, Kai-Chieh Kuo made high-density tubular weaving of ultra-fine filament yarns possible for the first time by means of suitable modifications to a shuttle loom as well as adaptations in the weaving preparation. In particular, he developed a new innovative reed technology that reduces warp thread friction during the shedding process and thus improves the process stability of the dense tube weaving process of fine yarns.

With the help of the process modification, it was then possible to produce high-density, thin-walled tubular woven fabrics, which were positively evaluated with regard to their suitability for a stent graft. Above all the potential of these tubular fabrics lies in their extremely thin-walled fabric profile, which seals well against blood. By using these new types of tubular fabrics as graft material for stent grafts, the system profile of the folded stent graft system can be reduced without having to compromise the blood tightness of the implant. The technology developed by Mr Kuo is not only applicable to stent graft systems, but also offers great possibilities for use in all other endovascular implants such as trans catheter heart valves, covered stents and small-lumen vascular prostheses.

Digital Pioneer Awards ceremony at the digitalCHURCH (c) digitalHUB Aachen e.V.; photo: Thomas Langens
Digital Pioneer Awards ceremony at the digitalCHURCH
15.06.2021

ITA Academy GmbH wins Digital Pioneer Award 2021

  • Digital Pioneer Awards ceremony at the digitalCHURCH
  • ITA Academy GmbH was honoured to receive the Digital Pioneer Award at the Digital Summit Event in Aachen on June 09, 2021.

The Digital Pioneer Award is given to companies that drive digitalisation with digital business models, processes or digital products. ITA Academy GmbH was honoured with the Digital Capability Center (DCC) Aachen and its support of companies in their digital transformation.

  • Digital Pioneer Awards ceremony at the digitalCHURCH
  • ITA Academy GmbH was honoured to receive the Digital Pioneer Award at the Digital Summit Event in Aachen on June 09, 2021.

The Digital Pioneer Award is given to companies that drive digitalisation with digital business models, processes or digital products. ITA Academy GmbH was honoured with the Digital Capability Center (DCC) Aachen and its support of companies in their digital transformation.

Using the latest didactic methods, sophisticated solution concepts and state-of-the-art technologies, the DCC Aachen supports people in keeping up with the digital future and becoming pioneers in digital transformation. In order to make innovative solutions such as AI and digital assistance systems tangible, the ITA Academy founded the Digital Capability Center (DCC) Aachen together with McKinsey & Company in 2017. The DCC is a model factory 4.0 in which digital applications are demonstrated and taught using the example of a realistic factory. The DCC thus offers a learning environment for companies in which participants are supported in building up competencies in the field of digital transformation in the form of practical work-shops.

The digital pioneers are to be publicised as best-practice examples in order to sensitize regional SMEs to the topic of digitisation. Around the award of the digital pioneers, the digitalHUB Aachen e.V. rolls out effective marketing activities. The pioneers achieve high visibility through the various planned campaigns and advertising opportunities.

AMAC kooperiert mit ITA (Institut für Textiltechnik der RWTH Aachen und deren ITA GmbH) für die weitere Geschäftsentwicklung im Bereich Composites  © AMAC
fltr: Markus Beckmann, Prof. Thomas Gries, Dr. Michael Effing, Dr. Christoph Greb
19.04.2021

AMAC cooperates with ITA

AMAC cooperates with ITA (Institute for Textile Technology of RWTH Aachen University and their ITA GmbH) for the business development in composites 

As of April 19th, 2021, AMAC is pleased to announce its cooperation with the Institute for Textile Technology, ITA, of RWTH Aachen University and their ITA GmbH. The aim of the cooperation is to strengthen and develop their business activities in composites.

AMAC cooperates with ITA (Institute for Textile Technology of RWTH Aachen University and their ITA GmbH) for the business development in composites 

As of April 19th, 2021, AMAC is pleased to announce its cooperation with the Institute for Textile Technology, ITA, of RWTH Aachen University and their ITA GmbH. The aim of the cooperation is to strengthen and develop their business activities in composites.

ITA, as one of the largest institutes on the campus of the excellence University RWTH Aachen, Germany, develops complete solutions from the manufacturing of the fiber itself over the processing of textile intermediates with thermoplastic and thermoset resins, textile-based part manufacturing, capabilities such as braiding, pultrusion and in-situ impregnation of textile preforms. Top 3 focused industries are transportation and particularly the e-mobility sector, building and construction as well as the wind energy sector. Additionally, ITA GmbH is the partner of the industry in R&D, focusing on 8 business segments, providing technology and knowledge transfer, as well as offering comprehensive solutions along the entire textile value chain.

Prof. Dr. Thomas Gries, Director of ITA, explains the background of the strategic cooperation with focus on composites: „Our long-term experience and unmatched know-how with all aspects of continuous fibers, non-wovens and web-based reinforcements allows us to deliver to the composite manufacturers a complete technology and service offer around the development of technical textiles, from the development of glass and carbon fibers to the textile-based processing of composite parts. In all process steps of our research and developments, we focus on sustainable and recyclable solutions, an efficient cost-performance ratio, the possible use of bio-based materials and the reduction of the CO2 footprint. We are glad to cooperate with Dr. Michael Effing and AMAC in order to benefit from his door-opening network in the composites industry. “

Dr. Michael Effing, Managing Director of AMAC GmbH: „I am very happy to support the ITA to generate innovation thanks to further industrial networking and pre-competitive joint projects. ITA is indeed a one-stop source for composite solutions from the fiber to the cost-efficient manufacturing of final parts. In the context of the Covid-19 impact to the entire industry, it makes sense to bundle forces. Furthermore, ITA, with its long tradition and satisfied customers offers further valuable networking opportunities to the composites industry as well as access to relevant complementary fiber-based excellence and 250 different technologies in their machine-park with an outstanding infrastructure in Aachen.”

Carbon reinforced concrete today: thin-walled curved barrel shells as roof elements at ITA (c) ITA. Carbon reinforced concrete today: thin-walled curved barrel shells as roof elements at ITA
05.06.2020

DFG funds Collaborative Research Centre / Transregio 280 on carbon reinforced concrete

  • Joint proposal of TUD and RWTH Aachen University

On 29 May, the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) decided to fund the Collaborative Research Centre (CRC)/Transregio 280 "Carbon reinforced concrete" at Technische Universität Dresden, short TUD, and RWTH Aachen University with the participation of the Institut für Textiltechnik, short ITA, with 12 million euros over the next four years.

The CRC/Transregio 280 “Design Strategies for Material-Minimised Carbon Reinforced Concrete Structures - Principles of a New Approach to Construction” breaks with the traditional way of designing reinforced concrete plants. The interdependence of reinforcement and matrix is being investigated in depth and a completely new design and construction strategy for building with carbon reinforced concrete is being developed.

  • Joint proposal of TUD and RWTH Aachen University

On 29 May, the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) decided to fund the Collaborative Research Centre (CRC)/Transregio 280 "Carbon reinforced concrete" at Technische Universität Dresden, short TUD, and RWTH Aachen University with the participation of the Institut für Textiltechnik, short ITA, with 12 million euros over the next four years.

The CRC/Transregio 280 “Design Strategies for Material-Minimised Carbon Reinforced Concrete Structures - Principles of a New Approach to Construction” breaks with the traditional way of designing reinforced concrete plants. The interdependence of reinforcement and matrix is being investigated in depth and a completely new design and construction strategy for building with carbon reinforced concrete is being developed.

Carbon reinforced concrete enables completely new design and construction possibilities in the building industry. The reasons for this are its very high strength and the possibility of a very low concrete overlay of only a few millimetres, as carbon, unlike structural steel, does not rust. However, the successful use of the new material, which was awarded the German Future Prize in 2016, requires completely new design and production strategies, which are being investigated in the CRC/Transregio.

Up to now, textile reinforcements have been coated and cured prior to component manufacture. This process is called offline consolidation. These stiff semi-finished products are not suitable for the production of complex components based on new, digital and continuous manufacturing processes (including 3D concrete printing and concrete extrusion). Therefore, ITA is investigating in the sub-project B02 of the CRC/Transregio how forming and consolidation steps are shifted in time by prepreg systems into the concreting process and how they can be applied within the new digital continuous manufacturing processes. In addition to established curing mechanisms, such as by heat or UV radiation, new approaches are also being researched. These new approaches include activation via the alkalinity of the concrete, microwaves and induction

The TUD and RWTH Aachen were awarded the grant on the basis of many years of experience in the research field of textile reinforced concrete. The material textile reinforced concrete was developed in two special research areas at both universities from 1999-2011 and was first fundamentally researched.

19 individual institutes are involved in the CRC/Transregio 280. The spokesman of the TUD is Professor Dr Manfred Curbach, the spokesman of the RWTH is Professor Dr Josef Hegger.

Source:

Institut für Textiltechnik der RWTH Aachen University, ITA

Steuerung eines Industrieroboters per Datenhandschuh Institut für Textiltechnik der RWTH Aachen University
Steuerung eines Industrieroboters per Datenhandschuh
04.04.2017

Wirtschaftlicher Erfolg durch Industrie 4.0: Digital Capability Center in Aachen eröffnet

Der Forschungsstandort Aachen ist um ein einmaliges Angebot reicher: Am Freitag eröffnete mit dem Digital Capability Center (DCC) eine neuartige Lernfabrik mit dem Schwerpunkt Industrie 4.0. In einer realitätsgetreuen Fabrikumgebung erhalten Fach- und Führungskräfte produzierender Unternehmen sowie angehende Ingenieure das Handwerkszeug, um die digitale Transformation im eigenen Unternehmen voranzutreiben. Das Motto: erkunden, ausprobieren, anwenden. Das DCC ist eine Kooperation der Unternehmensberatung McKinsey & Company, des Instituts für Textiltechnik (ITA) der RWTH Aachen University und führenden Technologieunternehmen wie dem Softwareanbieter PTC. Das DCC ist das erste seiner Art weltweit – weitere DCCs werden von McKinsey in diesem Jahr noch in Singapur, Chicago, Peking und Venedig eröffnet.

Der Forschungsstandort Aachen ist um ein einmaliges Angebot reicher: Am Freitag eröffnete mit dem Digital Capability Center (DCC) eine neuartige Lernfabrik mit dem Schwerpunkt Industrie 4.0. In einer realitätsgetreuen Fabrikumgebung erhalten Fach- und Führungskräfte produzierender Unternehmen sowie angehende Ingenieure das Handwerkszeug, um die digitale Transformation im eigenen Unternehmen voranzutreiben. Das Motto: erkunden, ausprobieren, anwenden. Das DCC ist eine Kooperation der Unternehmensberatung McKinsey & Company, des Instituts für Textiltechnik (ITA) der RWTH Aachen University und führenden Technologieunternehmen wie dem Softwareanbieter PTC. Das DCC ist das erste seiner Art weltweit – weitere DCCs werden von McKinsey in diesem Jahr noch in Singapur, Chicago, Peking und Venedig eröffnet.

Die praxisnahen Workshops im DCC helfen Unternehmen, sich dem Thema Industrie 4.0 systematisch und zielgerichtet zu nähern. Sie lernen, wo und wie neueste Technologien entlang der gesamten Wertschöpfungskette eingesetzt werden können – von der ersten Kundenanfrage über die Entwicklung, Produktion und Auslieferung bis zum Servicegeschäft. Aber auch die Anforderungen an das Management sowie die Befähigung der Mitarbeiter und die allgemeine Akzeptanz der mit der Transformation einhergehenden Veränderungen werden thematisiert. Workshop-Teilnehmer erarbeiten konkrete Lösungen für ihre individuelle Problemstellung und erhalten Einblick in zentrale digitale Lösungen und Technologien wie Echtzeit-Diagnosewerkzeuge, Big Data Analytics, prädiktive Instandhaltung, digitales Performancemanagement, 3D-Druck oder kollaborative Roboter.

Source:

Institut für Textiltechnik der RWTH Aachen University