From the Sector

Reset
623 results
(c) Coperion GmbH
24.06.2022

Coperion: New Development for Plastic Fiber and Flake Recycling

With the goal of making recycling of lightweight, high-volume fiber and flake recyclate much more economical and, in some cases even possible, Coperion has developed a new version of its ZS-B side feeder. Using the innovative ZS-B MEGAfeed, plastic recyclate with a bulk density under 200 kg/m³, long considered intake-limited and thus not worth recycling, can be reliably fed in large quantities into Coperion’s ZSK twin screw extruder and be concurrently recycled and compounded.

The ZS-B side feeder’s novel design makes it possible to feed very high rates of fiber and flakes, such as PA, PE, PET, and PP. As a result, the ZSK twin screw extruder’s high capacity can be fully exploited when the ZS-B MEGAfeed is used. Very high throughputs in both mechanical and chemical recycling of post-industrial and post-consumer waste are achieved.

With the goal of making recycling of lightweight, high-volume fiber and flake recyclate much more economical and, in some cases even possible, Coperion has developed a new version of its ZS-B side feeder. Using the innovative ZS-B MEGAfeed, plastic recyclate with a bulk density under 200 kg/m³, long considered intake-limited and thus not worth recycling, can be reliably fed in large quantities into Coperion’s ZSK twin screw extruder and be concurrently recycled and compounded.

The ZS-B side feeder’s novel design makes it possible to feed very high rates of fiber and flakes, such as PA, PE, PET, and PP. As a result, the ZSK twin screw extruder’s high capacity can be fully exploited when the ZS-B MEGAfeed is used. Very high throughputs in both mechanical and chemical recycling of post-industrial and post-consumer waste are achieved.

Increased Throughput in Numbers
With a ZSK 58 Mc18 twin screw extruder, the throughput increase and thus the potential of the new ZS-B MEGAfeed becomes very clear. When recycling PA fibers with a bulk density of ~40-50 kg/m3, throughputs of 70 kg/h were previously achieved using conventional equipment. When the PA fibers were fed into the ZSK extruder using the ZS-B MEGAfeed, throughputs increased about fourteenfold to 1,000 kg/h. Similar results were achieved recycling carbon fibers with a bulk density of ~50-70 kg/m3; in this case, throughputs increased from 50 kg/h to 2,500 kg/h using the ZS-B MEGAfeed. When recycling PCR (Post-Consumer Recycled) flakes, throughputs increased from 50 kg/h to 700 kg/h, and from 80 kg/h to 1,300 kg/h with multilayer film flakes.

Key to Economical Recycling of A Wide Variety of Plastics
Plastics previously considered not recyclable are becoming a valuable raw material using the new Coperion ZS-B MEGAfeed. For example, PCR flakes or recyclate from carbon fiber-reinforced plastics can now be fed into the ZSK extruder at high feed rates and recycled economically.

In the case of mechanical upcycling, upstream processes necessary for compounding, such as compacting, melting and agglomeration, are completely eliminated using the ZS-B MEGAfeed technology. In this recycling process, flakes and fibers can be fed directly into the ZSK extruder, where they are melted, compounded, devolatilized, and filtered in a single step. In so doing, both investment costs and energy consumption drop. The production process becomes significantly more efficient. Moreover, the thermal product stress is reduced and recyclate quality increases.

Even when recycling PET, the feed rate is no longer a limiting factor. With the ZS-B MEGAfeed, PET flakes and fibers can be fed into the ZSK twin screw extruder in large quantities with no pre-drying or crystallizing, where they can be processed with the highest degree of profitability.

The ZS-B MEGAfeed can also feed large quantities of post-consumer waste, adding appreciable value to the chemical recycling process with the ZSKs. ZSK throughput rates are very high with the ZS-B MEGAfeed. Preheating of the recyclate via mechanical energy input of the twin screws thus becomes even more economical for further processing in the reactor.

Existing Coperion extruders can be retrofitted with ZS-B MEGAfeed technology to greatly expand their spectrum of applications and increase their throughput rates.

Source:

Coperion GmbH / Konsens Public Relations GmbH & Co. KG

23.06.2022

Lectra announces the launch of its Automotive Cutting Room 4.0 offer

The automotive industry currently faces a complex set of market dynamics: rising material and transport costs, reduced budgets, changing consumer expectations, increasing challenges related to CSR, etc. In this context, improving efficiency across the whole value chain has become a strategic priority for vehicle and equipment manufacturers. Lectra supports its customers by designing and developing cutting-edge solutions that combine software, equipment, data and services to make its offer the gateway to Industry 4.0.
 
With Industry 4.0, a new range of possibilities is opening up to businesses. The concept and its technologies bring in new value creation and cost control models based on synchronized, flexible and fast processes.
 

The automotive industry currently faces a complex set of market dynamics: rising material and transport costs, reduced budgets, changing consumer expectations, increasing challenges related to CSR, etc. In this context, improving efficiency across the whole value chain has become a strategic priority for vehicle and equipment manufacturers. Lectra supports its customers by designing and developing cutting-edge solutions that combine software, equipment, data and services to make its offer the gateway to Industry 4.0.
 
With Industry 4.0, a new range of possibilities is opening up to businesses. The concept and its technologies bring in new value creation and cost control models based on synchronized, flexible and fast processes.
 
The Automotive Cutting Room 4.0 offer is a set of solutions connected to one other: Vector, the fabric cutting equipment offering the best performance in the market; Empower, a new generation of digital services to leverage Vector's capabilities; Valia, the heart of the new offer, a software for preparing and scheduling production; and Algopex, an application for exploiting and capitalizing on all the data generated by the cutting room, so you can make the best decisions as quickly as possible.
 
Connecting up all the elements of the Automotive Cutting Room 4.0 offer delivers this unprecedented value and enables an unparalleled level of performance to be achieved. Nicolas Favreau, Lectra’s Automotive Marketing Strategy Director, explains: “When the whole cutting room process is digitalized, the data generated are centralized and accessible in real time, helping our customers to make the best decisions at every step of the production process. The benefits are huge. For example, the key performance indicators from the offer’s first users show productivity gains of around 5% and a reduction in material consumption of nearly 2%. That’s unheard of! These results, combined with the agility that the Automotive Cutting Room 4.0 brings and the complete process control, demonstrate the offer’s maximum relevance.”

Source:

Lectra 

21.06.2022

SHIMA SEIKI to exhibit at Pitti Filati 91

SHIMA SEIKI ITALIA S.p.A. will exhibit at the 91st edition of the Pitti Immagine Filati exhibition in Florence, Italy from 29th June till 1st July, 2022. Products exhibited will include the SWG-FIRST124 and N.SIR123SP computerized flat knitting machines as well as APEXFiz™ design software.

The renewed SWG-FIRST124 is a synthesis of all of SHIMA SEIKI’s experience and know-how in computerized shaped knitting, realizing a tremendous range of knitting from full-fashioning and rib shaping to integral knitting. This all-purpose capability is made possible by the revolutionary SlideNeedle™, which, together with loop pressers and transfer jacks, offers remarkable variety, expanding the boundaries of flat knitting with the capability to produce garments that were previously impossible to produce.

SHIMA SEIKI ITALIA S.p.A. will exhibit at the 91st edition of the Pitti Immagine Filati exhibition in Florence, Italy from 29th June till 1st July, 2022. Products exhibited will include the SWG-FIRST124 and N.SIR123SP computerized flat knitting machines as well as APEXFiz™ design software.

The renewed SWG-FIRST124 is a synthesis of all of SHIMA SEIKI’s experience and know-how in computerized shaped knitting, realizing a tremendous range of knitting from full-fashioning and rib shaping to integral knitting. This all-purpose capability is made possible by the revolutionary SlideNeedle™, which, together with loop pressers and transfer jacks, offers remarkable variety, expanding the boundaries of flat knitting with the capability to produce garments that were previously impossible to produce.

The N.SIR123SP computerized knitting machine with intarsia capability features a special loop presser bed for producing hybrid inlay fabrics with both knit and weave characteristics. N.SIR123SP will also feature the special i-Plating option, capable of alternating yarn colors in any pattern, producing jacquard-like designs using plain jersey stitch. Plating can be performed within the same course and for individual needles. In combination with the loop presser and spring-type moveable sinker system even greater diversity in knit design is possible.

APEXFiz™ is subscription-based design software that supports the creative side of fashion from planning and design to colorway evaluation, realistic fabric simulation and 3D virtual sampling. Virtual samples are a digitized version of sample making that are accurate enough to be used effectively as prototypes, replacing physical sampling and consequently reducing time, cost and material that otherwise go to waste. APEXFiz™ thereby helps to realize sustainability and digitally transform the fashion supply chain.

Continuing from past editions of Pitti Filati are knit samples produced in collaboration with Italian designer Vittorio Branchizio. Staff at the SHIMA SEIKI booth will be donning knit uniforms produced as a collaborative effort between SHIMA SEIKI ITALIA, knitting companies and yarn companies.

Source:

SHIMA SEIKI MFG., LTD.

21.06.2022

RUDOLF celebrates its 100th birthday at TECHTEXTIL

  • New product initiatives and a system solution.

In the year of its 100th birthday RUDOLF will be at TECHTEXTIL to present its latest innovations and process solutions. Since 1922, RUDOLF offers a wide portfolio of specialty chemicals aiming to increase innovation and sustainability along the entire value chain, from fiber to finish.


At TECHTEXTIL, RUDOLF will present four new product initiatives and one system solution. The Company will hold “Conscious Performance” short seminars at its booth to present them.

New product initiatives
BIO-LOGIC® - Performance products with bio-carbon at core. Textile functionality is ensured through natural, renewable raw materials that are neither chemically nor genetically modified and that are not competing as food, feed or fuel.

CYCLE-LOGIC® - A new path: the upcycling of post-consumer, disposable and non-returnable plastics into valuable textile chemistry. Recycled PET bottles are now raw material for the manufacturing of some of our textile auxiliaries without attacking new, virgin resources.

  • New product initiatives and a system solution.

In the year of its 100th birthday RUDOLF will be at TECHTEXTIL to present its latest innovations and process solutions. Since 1922, RUDOLF offers a wide portfolio of specialty chemicals aiming to increase innovation and sustainability along the entire value chain, from fiber to finish.


At TECHTEXTIL, RUDOLF will present four new product initiatives and one system solution. The Company will hold “Conscious Performance” short seminars at its booth to present them.

New product initiatives
BIO-LOGIC® - Performance products with bio-carbon at core. Textile functionality is ensured through natural, renewable raw materials that are neither chemically nor genetically modified and that are not competing as food, feed or fuel.

CYCLE-LOGIC® - A new path: the upcycling of post-consumer, disposable and non-returnable plastics into valuable textile chemistry. Recycled PET bottles are now raw material for the manufacturing of some of our textile auxiliaries without attacking new, virgin resources.

PRISTINE® - Hygiene and freshness from continuous R&D advances. RUDOLF’s new ingredient brand that groups all high-performing technologies for textile hygiene, protection and freshness.

BIONIC FINISH® ECO - An idea borrowed from Mother Nature. Based on proprietary dendrimer technology, RUDOLF presents an extended family of unique fluorine-free DWR formulations suited for different materials and designed for different applications and needs.

New system solution
ECO-LOGIC® - Two-steps process designed and managed by RUDOLF’s specialists in textile process chemistry. It simulates, analyses and measures the environmental impact of a given industrial textile process to then provide insights into the optimization of resources, costs and CO2 emissions..

Source:

RUDOLF GmbH

Graphic: RadiciGroup
20.06.2022

RadiciGroup at Techtextil with innovative textile solutions

  • Target markets: automotive, furnishings, sports and technical apparel
  • New product entry: radipeople® line of personal protective equipment

RadiciGroup is at Techtextil 2022, the leading European trade fair for technical textiles, taking place in Frankfurt am Main, Germany, from 21 to 24 June. On display in the RadiciGroup exhibition area are the Group’s latest products for the automotive, furnishings and apparel markets: from nylon and polyester yarn, including biosource and recycled lines, to nonwovens and the new radipeople® line of personal protective equipment (PPE).

Indeed, at Techtextil, RadiciGroup is showcasing RENYCLE®, a yarn obtained from recycled nylon; REPETABLE®, a polyester yarn from post-consumer recycled plastic bottles; RESPUNSIBLE®, a nonwoven fabric from recycled polypropylene; and BIOFEEL®, a brand identifying a yarn line obtained from renewable sources of both nylon and polyester.

  • Target markets: automotive, furnishings, sports and technical apparel
  • New product entry: radipeople® line of personal protective equipment

RadiciGroup is at Techtextil 2022, the leading European trade fair for technical textiles, taking place in Frankfurt am Main, Germany, from 21 to 24 June. On display in the RadiciGroup exhibition area are the Group’s latest products for the automotive, furnishings and apparel markets: from nylon and polyester yarn, including biosource and recycled lines, to nonwovens and the new radipeople® line of personal protective equipment (PPE).

Indeed, at Techtextil, RadiciGroup is showcasing RENYCLE®, a yarn obtained from recycled nylon; REPETABLE®, a polyester yarn from post-consumer recycled plastic bottles; RESPUNSIBLE®, a nonwoven fabric from recycled polypropylene; and BIOFEEL®, a brand identifying a yarn line obtained from renewable sources of both nylon and polyester.

Moreover, RadiciGroup is participating in a forum organized by the Technical Textiles Section of Sistema Moda Italia in collaboration with the Italian Space Agency (ICE) (Hall 12.1 – Stand C58), with the goal of introducing product innovations not only coming from a single manufacturer, but also from an innovative synergistic approach all along the supply chain, from raw materials to finished products. An example of this synergistic collaboration is the “Mars Spacesuit”, recently tested in the USA by analogue astronauts as part of a space medicine project designed to measure the vital signs of future astronauts and develop technologies to support the simulation of life in space and planetary environments. RadiciGroup teamed up with major Italian textile companies and supplied the materials to make the suits for the six analogue astronauts participating in the mission and coordinated the development of the technologies needed to create the technicalwear for use in extreme environmental conditions.

 

Source:

RadiciGroup

20.06.2022

Beaulieu Fibres International at Techtextil 22

  • Bio circular Fibre - Shaping Sustainable Living

The European staple fibre producer Beaulieu Fibres International turns the spotlight on future-focused solutions for nonwovens & engineered fabrics at Techtextil 22. A key priority is innovation in polyolefin fibres and bicomponent polyester/polyolefin fibres, to advance sustainable design, end-of-life recyclability, and resource and carbon footprint reduction for industrial and hygiene applications.

The new sustainability roadmap - Route 2030 outlines how the company is targeting the reduction of our environmental footprint to zero, taking care of people and doing business in a transparent, ethical way. Sustainability is key to Beaulieu Fibre International’s long-term strategy, and the company is heavily focused on defining its green portfolio to support evolution in diverse market applications and to work towards a circular economy with the whole supply chain.

  • Bio circular Fibre - Shaping Sustainable Living

The European staple fibre producer Beaulieu Fibres International turns the spotlight on future-focused solutions for nonwovens & engineered fabrics at Techtextil 22. A key priority is innovation in polyolefin fibres and bicomponent polyester/polyolefin fibres, to advance sustainable design, end-of-life recyclability, and resource and carbon footprint reduction for industrial and hygiene applications.

The new sustainability roadmap - Route 2030 outlines how the company is targeting the reduction of our environmental footprint to zero, taking care of people and doing business in a transparent, ethical way. Sustainability is key to Beaulieu Fibre International’s long-term strategy, and the company is heavily focused on defining its green portfolio to support evolution in diverse market applications and to work towards a circular economy with the whole supply chain.

Beaulieu Fibres International will offer ISCC Plus (International Sustainability and Carbon Certification Plus) certified bio circular MONO-PP and BICO PP/PE fibres in 1,3-8,9 dtex, available with all the main available finish classes. These drop-in solutions, with no loss in quality, will support customers reduce reliance on virgin fossil carbon in their nonwoven and engineered fibre applications, contributing to the transition towards a circular economy.

Source:

Beaulieu Fibres International

(c) A. Monforts Textilmaschinen GmbH & Co. KG
20.06.2022

Monforts introduces range of modular upgrades

Monforts is introducing a range of modular upgrades that can be added to existing finishing lines already in production.

The Monforts universal Energy Tower – a flexible, free-standing air/air heat exchanger for recovering the heat from the exhaust air flow of thermal processes – can result in a 30% reduction in the energy consumed by a line, depending on the exhaust air volume and operating temperature.

A Monforts Eco Booster, completely integrated into the chamber design of the Montex stenter, is another retrofitting option. As a single state-of-the-art heat recovery system with automatic cleaning, it can be added to existing ranges. For ranges of up to eight chambers only one module is necessary to achieve significant energy savings.

On an eight-chamber stenter with an operating width of two metres carrying out a fixing process on a 150gsm woven fabric, for example, the energy savings have been calculated to be 35% over an annual schedule of 6,000 operating hours.

In addition, the Eco Booster consumes only minimal amounts of water during the cleaning cycle and the entire process is controlled and monitored automatically.

Monforts is introducing a range of modular upgrades that can be added to existing finishing lines already in production.

The Monforts universal Energy Tower – a flexible, free-standing air/air heat exchanger for recovering the heat from the exhaust air flow of thermal processes – can result in a 30% reduction in the energy consumed by a line, depending on the exhaust air volume and operating temperature.

A Monforts Eco Booster, completely integrated into the chamber design of the Montex stenter, is another retrofitting option. As a single state-of-the-art heat recovery system with automatic cleaning, it can be added to existing ranges. For ranges of up to eight chambers only one module is necessary to achieve significant energy savings.

On an eight-chamber stenter with an operating width of two metres carrying out a fixing process on a 150gsm woven fabric, for example, the energy savings have been calculated to be 35% over an annual schedule of 6,000 operating hours.

In addition, the Eco Booster consumes only minimal amounts of water during the cleaning cycle and the entire process is controlled and monitored automatically.

The Matex Eco Applicator is an alternative to the conventional padding process for energy-conscious finishing and achieving considerable savings in the energy required for drying treated fabrics. The precise amount of chemical can be applied to the fabric and with less residual moisture after application of only approximately 35% so that less drying capacity is required in the stenter, which leads to huge energy savings.

Finishes can be evenly applied on either or both sides of the fabric, and two separate treatments can be applied to front and back. This makes the unit ideal for the production of, for example, double-performance hydrophobic/hydrophilic fabrics for professional clothing, as well as the over dyeing or finishing of denim fabrics.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

20.06.2022

Lectra joins Euronext Tech Leaders

Lectra, whose connected industrial equipment and software facilitate the digital transformation and Industry 4.0 transition of fashion, automotive and furniture companies, announces its selection for the new Euronext Tech Leaders stock market index. This brings Lectra into the community of European technology leaders identified by Euronext as innovative and high-growth companies.

The new Euronext Tech Leaders market index, launched on June 7, comprises 100 European technology companies listed on the Euronext markets, which meet various performance and growth criteria. With the launch of this initiative, Euronext aims to offer better visibility and new services to selected European technology leaders.

Lectra, whose connected industrial equipment and software facilitate the digital transformation and Industry 4.0 transition of fashion, automotive and furniture companies, announces its selection for the new Euronext Tech Leaders stock market index. This brings Lectra into the community of European technology leaders identified by Euronext as innovative and high-growth companies.

The new Euronext Tech Leaders market index, launched on June 7, comprises 100 European technology companies listed on the Euronext markets, which meet various performance and growth criteria. With the launch of this initiative, Euronext aims to offer better visibility and new services to selected European technology leaders.

Lectra is one of the 41 French companies that are now members of Euronext Tech Leaders. The company, founded in 1973 on a close relationship with fashion industry players, has also for the last three decades worked globally with automotive equipment and furniture manufacturers. In its three strategic markets, Lectra sells connected equipment that optimizes the cutting processes of fabric, leather and other soft materials used by manufacturers, and markets software and services that streamline their production processes while enabling them to be more agile and make considerable material savings.

In fashion, through the use of market data – made accessible and exploitable by the Internet of Things, the cloud, artificial intelligence and big data – Lectra’s software solutions also enable a better understanding of consumers’ behavior. They therefore facilitate strategic decision-making for brands, manufacturers and distributors at the key steps in the value chain of design, production and distribution. In this industry, the impact of Lectra’s solutions on reducing material consumption is even greater because it takes effect as early as the garment design stage.

Technology and innovation are therefore at the heart of Lectra’s strategy, with the company aiming to become a key player in Industry 4.0 in its strategic markets by 2030.

Source:

Lectra

15.06.2022

Lenzing partners with TfS to build global sustainable supply chains

  • Lenzing continues to focus on partnering for systemic change

  • Clear commitment to improving the environmental footprint of textile and nonwoven industries

  • Global initiative TfS promotes sustainable design of global supply chains

The Lenzing Group, a world-leading provider of wood-based specialty fibers for the global textile and nonwoven industries, has joined the chemical industry’s sustainable supply chain initiative, Together for Sustainability (TfS). Together with Lenzing, numerous internationally active chemical companies have joined the initiative. Their common goal is to make the global supply chains of the chemical industry sustainable.

  • Lenzing continues to focus on partnering for systemic change

  • Clear commitment to improving the environmental footprint of textile and nonwoven industries

  • Global initiative TfS promotes sustainable design of global supply chains

The Lenzing Group, a world-leading provider of wood-based specialty fibers for the global textile and nonwoven industries, has joined the chemical industry’s sustainable supply chain initiative, Together for Sustainability (TfS). Together with Lenzing, numerous internationally active chemical companies have joined the initiative. Their common goal is to make the global supply chains of the chemical industry sustainable.

“Joining the TfS initiative is another clear commitment to improving the environmental footprint of the global textile and nonwoven industries and proves that sustainability is taken very seriously at Lenzing – so much so that sustainability is at the heart of our business strategy. So much so, it sits at the core of the Group’s business strategy. The industry needs innovation in order to transition from linear to circular ways of working, and Lenzing will continue to partner across the supply chain to bring this vision to life,” says Robert van de Kerkhof, Chief Commercial Officer Fiber at Lenzing.

Partnering for systemic change
Complex global sustainability challenges require a collaborative approach to developing systemic solutions, involving many stakeholder groups. In order to make the global textile and nonwovens industries more sustainable and bring about systemic change, Lenzing has therefore also been building on partnerships within its sustainability strategy “Naturally Positive” for many years.

“I am very proud to welcome Lenzing to the TfS family, bringing the TfS membership to 37 companies. Together and with our strategic partners we continue to expand our reach and increase our impact on the sustainability performance in chemical supply chains. Given the regulatory landscape, climate challenges and market conditions, the need for sustainable businesses only intensifies. TfS is the crucial enabler to make supply chains and businesses at large more sustainable and contribute to developing a better world”, says TfS President Bertrand Conquéret.

The global TfS initiative follows the principles of the UN Global Compact and Responsible Care.

 

Source:

Lenzing AG

Baldwin’s non-contact spray technology Texcoat G4. (Photo: Baldwin)
15.06.2022

Archroma and Baldwin to collaborate for optimized performance and resource saving in textile finishing

Archroma, a global leader in specialty chemicals towards sustainable solutions, and Baldwin, a leading global manufacturer and supplier of precision spray systems and technology for sustainable textile manufacturing, announce a new collaboration to optimize performance and resource saving in the finishing department.

The two companies aim to support textile manufacturers in their development projects, targeting to improve their product safety, performance and functionality, while at the same time maximizing the productivity and resource utilization of the finishing application process.

Archroma and Baldwin are collaborating in multiple projects that combine Archroma’s most sustainable product innovations with Baldwin’s Texcoat G4.

TexCoat G4 is a non-contact spray technology for textile finishing and remoistening, designed to allow a controlled and optimal coverage of the exact amount of finish chemistry for reaching specific characteristics of the fabric. The system can be used to reduce water consumption by as much as 50% compared to traditional padding application processes.

Archroma, a global leader in specialty chemicals towards sustainable solutions, and Baldwin, a leading global manufacturer and supplier of precision spray systems and technology for sustainable textile manufacturing, announce a new collaboration to optimize performance and resource saving in the finishing department.

The two companies aim to support textile manufacturers in their development projects, targeting to improve their product safety, performance and functionality, while at the same time maximizing the productivity and resource utilization of the finishing application process.

Archroma and Baldwin are collaborating in multiple projects that combine Archroma’s most sustainable product innovations with Baldwin’s Texcoat G4.

TexCoat G4 is a non-contact spray technology for textile finishing and remoistening, designed to allow a controlled and optimal coverage of the exact amount of finish chemistry for reaching specific characteristics of the fabric. The system can be used to reduce water consumption by as much as 50% compared to traditional padding application processes.

Archroma and Baldwin are currently testing Archroma’s finishing products and systems, such as the soon-to-be-launched PFC-free* Smartrepel® Hydro SR for water-based soil repellence, as well as metal and inorganic particle-free antimicrobial technologies like Sanitized T 20-19 and TH 15-14, which will be launched at the upcoming Techtextil 2022.

The first test results will be available for discussions with both partners at Techtextil at their respective booths.

14.06.2022

Members of TMAS at Texprocess, Techtextil and Heimtextil in Frankfurt

ACG Nyström, a member of TMAS, the Swedish textile machinery association, will demonstrate the automated Talon 75 multi-ply cutter at the forthcoming Texprocess exhibition in Frankfurt, Germany, from June 21-24.

The Talon 75 is capable of cutting up to 7.5cm of compressed materials common to the sewn products and technical textiles industries. The machine is engineered to automatically pull stacked material plies from the spreading table to a modular, bristle-block conveyor bed for reciprocating knife cutting of patterns. Precise system operations with state-of-the-art motion control communications offer an industrial-strength solution.

Industry 4.0 ready
Eastman’s Talon multi-ply cutting systems are Industry 4.0 ready and equipped with the latest in condition based predictive maintenance technology. Their robust design utilises motors and amplifiers that automatically detect changes in critical components to notify operators well in advance of maintenance prompts. Also on display in Frankfurt will be Eastman’s ES-960, a material spreader capable of fast and easy spreading heights up to 20cm.

ACG Nyström, a member of TMAS, the Swedish textile machinery association, will demonstrate the automated Talon 75 multi-ply cutter at the forthcoming Texprocess exhibition in Frankfurt, Germany, from June 21-24.

The Talon 75 is capable of cutting up to 7.5cm of compressed materials common to the sewn products and technical textiles industries. The machine is engineered to automatically pull stacked material plies from the spreading table to a modular, bristle-block conveyor bed for reciprocating knife cutting of patterns. Precise system operations with state-of-the-art motion control communications offer an industrial-strength solution.

Industry 4.0 ready
Eastman’s Talon multi-ply cutting systems are Industry 4.0 ready and equipped with the latest in condition based predictive maintenance technology. Their robust design utilises motors and amplifiers that automatically detect changes in critical components to notify operators well in advance of maintenance prompts. Also on display in Frankfurt will be Eastman’s ES-960, a material spreader capable of fast and easy spreading heights up to 20cm.

Members of TMAS will be showcasing a range of solutions aligning with the growing trend for more localised and automated textile manufacturing at the forthcoming Texprocess, Techtextil and Heimtextil shows which are all taking place in Frankfurt from June 21-24.

Source:

TMAS / AWOL Media

(c) SHIMA SEIKI MFG., LTD.
14.06.2022

SHIMA SEIKI to exhibit at Techtextil 2022 in Frankfurt

SHIMA SEIKI MFG., LTD. of Wakayama, Japan, along with its Italian subsidiary SHIMA SEIKI ITALIA S.p.A., will be participating in the Techtextil exhibition in Frankfurt, Germany from the 21st till the 24th of June 2022.

SHIMA SEIKI MFG., LTD. of Wakayama, Japan, along with its Italian subsidiary SHIMA SEIKI ITALIA S.p.A., will be participating in the Techtextil exhibition in Frankfurt, Germany from the 21st till the 24th of June 2022.

On display will be SHIMA SEIKI’s latest innovation in flat knitting technology as applied to the field of technical textiles—a prototype weft knitting machine capable of multi-axial yarn insertion. Fabrics produced on this machine use inlay technique for the production of hybrid textiles that combine the stretch characteristics of knitted fabrics with the stability of woven textiles, suited to various technical applications. To this, warp yarn is inserted to further expand its capability to produce 3D-shaped carbon fiber and composite preforms directly on the machine. This is made possible by taking advantage of the fact that flat knitting as a textile production method is capable of producing end products that are shaped-to-form and with added thickness. Compared to current methods of preform production, savings in post-processing time, material, labor and associated costs are immense, realizing efficient and sustainable production. SHIMA SEIKI’s own yarn unwinding technology is also used for optimum yarn feed and tension for use with technical yarns that are otherwise difficult to knit. Industrial textile samples knit on the multi-axial machine will also be available for examination on-site.

SHIMA SEIKI's SDS®-ONE APEX4 3D design system will be available for demonstrations as well. Of particular interest should be its ultra-realistic simulation capability that realizes Virtual Sampling. When countless variations must be evaluated before arriving at a final design, virtual product samples can be used to streamline the decision-making process by minimizing the enormous amount of time, cost and material normally associated with producing actual samples for each variation. When approved, the same data can be converted to machine data for immediate knitting, significantly reducing lead times.

(c) Trützschler Nonwovens & Man-Made Fibers GmbH
14.06.2022

Trützschler Man-Made Fibers presents OPTIMA systems for industrial yarns

Trützschler Man-Made Fibers introduces OPTIMA for IDY and expands the range of the OPTIMA extrusion systems by the industrial yarn (IDY) sector. In addition to OPTIMA for carpet yarns (MO40-C, MO40-E and TO40), variants for manufacturing (semi-)industrial multifilament yarns are now joining the line.

Since 2012, Trützschler has been developing and building high-performance extrusion lines for carpet yarns (BCF - Bulk Continuous Filament) and industrial/technical yarns made of polyester, polyamide and polypropylene. The market launch of the OPTIMA concept for BCF took place in 2019 and has established itself in the markets since then. OPTIMA was designed as a modular platform and now also includes solutions in the IDY (InDustrial Yarn) sector.

OPTIMA systems for industrial yarn (TEC-O40 and TEC-O80) impress with flexibility application and end product diversity. Both concepts offer a wide range of design options and can be tailored precisely to meet end product and the throughput requirements.

Trützschler Man-Made Fibers introduces OPTIMA for IDY and expands the range of the OPTIMA extrusion systems by the industrial yarn (IDY) sector. In addition to OPTIMA for carpet yarns (MO40-C, MO40-E and TO40), variants for manufacturing (semi-)industrial multifilament yarns are now joining the line.

Since 2012, Trützschler has been developing and building high-performance extrusion lines for carpet yarns (BCF - Bulk Continuous Filament) and industrial/technical yarns made of polyester, polyamide and polypropylene. The market launch of the OPTIMA concept for BCF took place in 2019 and has established itself in the markets since then. OPTIMA was designed as a modular platform and now also includes solutions in the IDY (InDustrial Yarn) sector.

OPTIMA systems for industrial yarn (TEC-O40 and TEC-O80) impress with flexibility application and end product diversity. Both concepts offer a wide range of design options and can be tailored precisely to meet end product and the throughput requirements.

OPTIMA enables the production of high-tenacity yarns for shoelaces, ropes and nets as well as low-shrinkage qualities for tire cords, truck tarpaulins and airbags. As the lines are modular, they can be quickly adapted to new market developments and end products.

Source:

Trützschler Nonwovens & Man-Made Fibers GmbH

13.06.2022

AkzoNobel launches mosquito-repellent coating

People in Brazil have a new ally in the fight against an invasive carrier of dengue fever – a mosquito-repellent coating developed by AkzoNobel’s Coral brand.
 
Known as Well-being Protection Anti-Mosquito, the colorless matt varnish contains an active ingredient called permethrin. Its repellent action is specifically designed to combat the Aedes aegypti mosquito, which was largely responsible for dengue cases in Brazil surging 165% during the first few months of 2022 – according to figures from the Brazilian Ministry of Health. As well as spreading dengue, Aedes aegypti can also transmit the zika and chikungunya virus.
 
When a mosquito lands on the new transparent topcoat, the permethrin is absorbed through its feet and over-excites the insect’s nervous system, causing it to disengage or fall off. Permethrin is a well-known repellent and is commonly used in fabrics for mosquito nets and protective clothing.

People in Brazil have a new ally in the fight against an invasive carrier of dengue fever – a mosquito-repellent coating developed by AkzoNobel’s Coral brand.
 
Known as Well-being Protection Anti-Mosquito, the colorless matt varnish contains an active ingredient called permethrin. Its repellent action is specifically designed to combat the Aedes aegypti mosquito, which was largely responsible for dengue cases in Brazil surging 165% during the first few months of 2022 – according to figures from the Brazilian Ministry of Health. As well as spreading dengue, Aedes aegypti can also transmit the zika and chikungunya virus.
 
When a mosquito lands on the new transparent topcoat, the permethrin is absorbed through its feet and over-excites the insect’s nervous system, causing it to disengage or fall off. Permethrin is a well-known repellent and is commonly used in fabrics for mosquito nets and protective clothing.

The effectiveness of Well-being Protection Anti-Mosquito was tested in an independent external laboratory, certified by the Brazilian Network of Analytical Laboratories in Health. All the tests took place on painted walls and ceilings in a life-size house environment and successfully proved that mosquitoes were repelled from the room after contact, with the active ingredient being retained in the varnish matrix.

Source:

AkzoNobel

(c) adidas AG
09.06.2022

adidas launches new Sportswear Capsule

adidas drops an all-new sportswear capsule. The collection is inspired by the way the next generation continues to turn tradition on its head with how they move through the world, opting for a fresh comfort-first mindset and rejecting old-world pressures.

To get closer to this mindset, adidas reached out to uncover more about the rise of the cosy fit. Nine in ten believe the clothes they wear impact how mentally comfortable they feel, and over three quarters say they are more likely to thrive in multiple aspects of life when rooted in a true feeling of comfort. With this in mind, adidas’ sportswear capsule is built for next-level comfort both at home and on the streets with a full collection of casual, stylish fits for both men and women.

Fronted by a raft of next generation trailblazers, including global award-winning actress Hoyeon, US gymnast sensation Nia Dennis, American football superstar Tua Tagavailoa, and Chinese national sprinting champion Xie Zhenye, the campaign reveals how choosing comfort in mind and body has given them confidence, more internal headspace, and the ability to embrace any challenges within their journey of progress.

adidas drops an all-new sportswear capsule. The collection is inspired by the way the next generation continues to turn tradition on its head with how they move through the world, opting for a fresh comfort-first mindset and rejecting old-world pressures.

To get closer to this mindset, adidas reached out to uncover more about the rise of the cosy fit. Nine in ten believe the clothes they wear impact how mentally comfortable they feel, and over three quarters say they are more likely to thrive in multiple aspects of life when rooted in a true feeling of comfort. With this in mind, adidas’ sportswear capsule is built for next-level comfort both at home and on the streets with a full collection of casual, stylish fits for both men and women.

Fronted by a raft of next generation trailblazers, including global award-winning actress Hoyeon, US gymnast sensation Nia Dennis, American football superstar Tua Tagavailoa, and Chinese national sprinting champion Xie Zhenye, the campaign reveals how choosing comfort in mind and body has given them confidence, more internal headspace, and the ability to embrace any challenges within their journey of progress.

Key looks include:

  • Women’s Rib Dress: A straight minimalist silhouette in block-colour black, which can be worn individually or layered for a more expressive look. Features a twister racerback detail, crew neck cut, and side split hem for an added edge
  • Men’s Classic Tee paired with Woven Pants and Coach Jacket: Paying homage to sport heritage, the woven pants and coach jacket offer an oversized and relaxed fit, in a neutral but bold colour pairing. The ribbed crewneck tee complements the look with a stylish mixture of textures
  • Women’s Oversized Hoodie with Rib Crop Top and Biker Shorts: A muted pastel toned top designed with a cropped hem and matching shorts in soft rib knit material, creating an effortless fresh but cosy look which can be easily layered with a slouchy oversized hoodie
  • Men’s Fleece Hoodie layered over Oversized Tee and Fleece Shorts: Relaxed fit basic tee with a vibrant red block logo paired with a boxy hooded jumper which boasts an oversized aesthetic. Complemented by baggy fleece-lined shorts ensures comfort through every move and moment
More information:
adidas Sportswear
Source:

adidas AG

08.06.2022

TEXAID enables Circularity Project R[ECO]LLECT

TEXAID with its Spanish subsidiary PERCENTIL enable Springfield to put its commitment to sustainability into action through implementing a circularity pilot project with the aim of giving a second life to second-hand garments. As part of the Tendam Group, who operates more than 2000 stores in 79 countries, Springfield partners with the TEXAID group, leading in the industry of collecting, sorting, reselling and recycling used garments, to launch the R[ECO]LLECT initiative.

Take-Back Program R[ECO]LLECT
With "the future is circular" as their call to action, the project is called R[ECO]LLECT and refers directly to the collection of all second-hand garments in good condition, to meet three clear sustainability objectives of Springfield: reduce the pressure on natural resources, reduce CO2 emissions and reduce the amount of textile waste.

R[ECO]LLECT was launched in May 2022 as a pilot project in 16 Springfield stores in Spain across different cities and provinces.

TEXAID with its Spanish subsidiary PERCENTIL enable Springfield to put its commitment to sustainability into action through implementing a circularity pilot project with the aim of giving a second life to second-hand garments. As part of the Tendam Group, who operates more than 2000 stores in 79 countries, Springfield partners with the TEXAID group, leading in the industry of collecting, sorting, reselling and recycling used garments, to launch the R[ECO]LLECT initiative.

Take-Back Program R[ECO]LLECT
With "the future is circular" as their call to action, the project is called R[ECO]LLECT and refers directly to the collection of all second-hand garments in good condition, to meet three clear sustainability objectives of Springfield: reduce the pressure on natural resources, reduce CO2 emissions and reduce the amount of textile waste.

R[ECO]LLECT was launched in May 2022 as a pilot project in 16 Springfield stores in Spain across different cities and provinces.

TEXAID’s Spanish subsidiary PERCENTIL is a strategic partner of Springfield in this step towards sustainability. The motto of PERCENTIL is that "there is nothing more sustainable than what you already have in your closet", and it is an intermediary between people who want to get rid of clothes and those who are looking to buy almost new clothes from brands recognized for their design and quality, but at a much lower price. In this way, textile overproduction is reduced, and the environmental impact is reduced. In addition, PERCENTIL receives the clothes, sorts them and takes care of giving them a second life.

More information:
Texaid Springfield circularity
Source:

Texaid

RadiciGroup slashed greenhouse gas emissions by 70% (c) RadiciGroup
08.06.2022

RadiciGroup slashed greenhouse gas emissions by 70%

Setting concrete environmental sustainability objectives for abating direct greenhouse gas emissions and leveraging investments and state-of-the-art technology. This is the approach that has always guided RadiciGroup in operating its businesses with a wide range of products: chemical intermediates, polyamide polymers, high performance engineering polymers and advanced textile solutions.

Between 2011 and 2020, overall Group greenhouse gas emissions were cut by 70%, falling from about 700,000 metric tons per year of CO2 equivalent to 200,000 metric tons.  

Setting concrete environmental sustainability objectives for abating direct greenhouse gas emissions and leveraging investments and state-of-the-art technology. This is the approach that has always guided RadiciGroup in operating its businesses with a wide range of products: chemical intermediates, polyamide polymers, high performance engineering polymers and advanced textile solutions.

Between 2011 and 2020, overall Group greenhouse gas emissions were cut by 70%, falling from about 700,000 metric tons per year of CO2 equivalent to 200,000 metric tons.  

These results were largely achieved through the action implemented by the Group’s Specialty Chemicals Business Area at its plants in Novara, Italy, and in Germany, which are the heart of RadiciGroup’s chemicals business. Here the Group produces an essential intermediate for synthesizing polyamide 66, adipic acid, whose production process releases nitrous oxide as a by-product. Nitrous oxide in itself is not particularly problematic (in fact, it is used in the medical sector as an anaesthetic and in the food industry as a spray propellant, in cans of whipped cream, for instance), but, if it is released into the atmosphere, it has a much higher greenhouse gas effect than carbon dioxide.

At the Radici Chimica site in Novara, a multiyear investment budget of over EUR 10 million was dedicated to lowering these emissions through three important undertakings: in 2004, putting into operation a three catalyst bed reactor, designed and patented by the company, to decompose nitrous oxide into nitrogen and oxygen, the two elements it is composed of, thus making it innocuous for the atmosphere; in 2013, installing an EnviNOx plant to decrease the release of nitrous oxide formed in the production of nitric acid, and, in 2021, a further improvement in the emissions abatement system associated with nitric acid production.

Since activating the last plant just 9 months ago, more than 35,000 metric tons of CO2 equivalent have been cut. All the above-mentioned actions have enabled Radici Chimica Novara to record a nitrous oxide emissions level less than 10 ppm, a value close to zero.

Source:

RadiciGroup

(c) Willy Bogner GmbH & Co. KGaA
07.06.2022

BOGNER and MICHELIN: Athluxury Sports Fashion meets function

BOGNER and the French tire manufacturer MICHELIN, are presenting a winter shoe collection for Autumn/Winter 2022. For the second winter season in a row, Munich-based BOGNER is working together with the shoe sole specialist MICHELIN.

The BOGNER|MICHELIN snowboots have a high performance sole, which offers excellent grip and major traction in all winter condition thanks to the particular design. MICHELIN's expertise in profile design meets 90 years of BOGNER’s heritage, which combines luxurious fashion, sports and unique design. The result: luxurious snowboots remarkably light in weight with high slip-resistance and the flexibility characteristic of a running shoe.

For Autumn/Winter 2022, the BOGNER Snowboot Collection will be launched with new features and designs. The BOGNER Snowker is a new shoe creation combining snowboot and sneaker. The blend of typical snowboot features with a true sneaker feeling combines Athluxury Sports Fashion with a tailor-made, technically advanced sole system.

BOGNER and the French tire manufacturer MICHELIN, are presenting a winter shoe collection for Autumn/Winter 2022. For the second winter season in a row, Munich-based BOGNER is working together with the shoe sole specialist MICHELIN.

The BOGNER|MICHELIN snowboots have a high performance sole, which offers excellent grip and major traction in all winter condition thanks to the particular design. MICHELIN's expertise in profile design meets 90 years of BOGNER’s heritage, which combines luxurious fashion, sports and unique design. The result: luxurious snowboots remarkably light in weight with high slip-resistance and the flexibility characteristic of a running shoe.

For Autumn/Winter 2022, the BOGNER Snowboot Collection will be launched with new features and designs. The BOGNER Snowker is a new shoe creation combining snowboot and sneaker. The blend of typical snowboot features with a true sneaker feeling combines Athluxury Sports Fashion with a tailor-made, technically advanced sole system.

Source:

Willy Bogner GmbH & Co. KGaA

07.06.2022

EFI confirms Acquisition of Inèdit Software for textile printing

Electronics For Imaging, Inc. announced that it has acquired Inèdit Software S.L., a developer of raster image processors (RIPs) and related software for digital industrial textile printing. The acquisition extends EFI’s strategy to accelerate digital transformation in industrial print through investments that advance the company’s presence and capabilities in Packaging & Corrugated, Display Graphics, Textile, and Building Materials/Décor applications. Inèdit will be integrated into the Reggiani textile business.

Electronics For Imaging, Inc. announced that it has acquired Inèdit Software S.L., a developer of raster image processors (RIPs) and related software for digital industrial textile printing. The acquisition extends EFI’s strategy to accelerate digital transformation in industrial print through investments that advance the company’s presence and capabilities in Packaging & Corrugated, Display Graphics, Textile, and Building Materials/Décor applications. Inèdit will be integrated into the Reggiani textile business.

Similar to EFI’s Fiery® digital front end and RIP technologies for the digital commercial and industrial printing markets, Inèdit’s neoStampa product is a recognized benchmark solution for RIPs in digital textile printing. The Inèdit product portfolio features advanced workflow solutions for textile profiling, calibration, design integration and much more. Inèdit’s RIP technology is employed across the worldwide textile industry and is one of the leading RIPs used to drive EFI Reggiani digital printers and other digital industrial textile printer brands. As part of EFI Reggiani, Inèdit will continue to support products for a broad range of digital printers.

Source:

EFI

06.06.2022

SHIMA SEIKI to exhibit at ITM 2022

SHIMA SEIKI MFG. will participate in the ITM 2022 International Textile Machinery Exhibition in Istanbul, Turkey.

SHIMA SEIKI MFG. will participate in the ITM 2022 International Textile Machinery Exhibition in Istanbul, Turkey.

SHIMA SEIKI will exhibit a wide range of its products, including proposals in seam-free WHOLEGARMENT® knitting technology that offers an alternative to labor-intensive manufacturing in Turkey and other international markets. Featured is the flagship MACH2XS WHOLEGARMENT® knitting machine with original SlideNeedle™ on four needle beds and spring-loaded moveable sinkers with expanded patterning capability, the MACH2VS V-bed machine for producing WHOLEGARMENT® items using every other needle, as well as the compact SWG091N2 for producing smaller WHOLEGARMENT® items and accessories. A brand new proposal in V-bed WHOLEGARMENT® knitting will also be introduced in the form of the N.SVR183 machine. N.SVR123SP features a special loop presser bed that can produce hybrid inlay fabrics with both knit and weave characteristics. N.SVR123SP at ITM will feature the special i-Plating option, capable of alternating yarn colors in any pattern, producing jacquard-like designs using plain jersey stitch for even greater diversity in knit design. Meanwhile N.SSR112 offers industry-leading technology in an economical yet reliable package made in Japan. Also on display is the SFG20 glove knitting machine.

Demonstrations will be performed on SHIMA SEIKI’s SDS®-ONE APEX4 design system. At the core of the company’s “Total Fashion System” concept, SDS®-ONE APEX4 provides comprehensive support throughout the production supply chain, integrating production into one smooth and efficient workflow from yarn development, product planning and design, to production and even sales promotion. Especially effective is the way SDS®-ONE APEX4 improves on the design evaluation process with its ultra-realistic simulation capability, whereby virtual samples replace physical sampling, consequently reducing time, cost and material that otherwise go to waste. The same capability is present in APEXFiz™ subscription-based design software. Installed on personal computers, APEXFiz™ features the same functionality as SDS®-ONE APEX4, but with the added versatility to adapt to different work styles and business environments including teleworking and telecommuting. Digital prototyping using virtual samples on SDS®-ONE APEX4 and APEXFiz™ help to digitally transform the fashion supply chain for realizing sustainable manufacturing. APEXFiz™ will be shown along with SHIMA SEIKI’s yarnbank™ digital yarn web platform that further enhances the realism of virtual samples.

Source:

SHIMA SEIKI MFG., LTD.