From the Sector

At the upcoming Techtextil show for technical textiles, which will take place in Frankfurt from April 23-25, Monforts will launch its new coaTTex coating unit dedicated to air knife and knife-over-roller coating.

For single-sided application with paste or foam, the versatile coaTTex is suitable for both incorporation into existing finishing ranges as well as installation with new Monforts lines, notably the Montex stenter systems.

A wide range of coatings can be applied to fabrics for providing functions such as waterproofing, liquid and gas protection and breathability, in addition to foam lamination and coating, including black-out coating.

The considerable technical textile end-use applications envisaged for the coaTTex range from window blinds to abrasive cloths and from airbags to sails.

With an operational speed of up to 40 metres per minute, coaTTex units are available in nominal widths of between 1800mm to 3600mm and their robust construction is characterised by a rotating beam for the fixation of up to three different knife executions.

Central adjustment of both the horizontal and vertical position of the beam, and also of the knife angle, enables easy adaptation to new projects and automatic tension control guarantees high quality production. In addition, the cleaning blade for the coating roller is pneumatically controlled, as is the lifting of the beam at seams and clamping during fabric standstill.

The “Cellulose Fibres Conference 2024” held in Cologne on 13-14 March demonstrated the innovative power of the cellulose fibre industry. Several projects and scale-ups for textiles, hygiene products, construction and packaging showed the growth and bright future of this industry, supported by the policy framework to reduce single-use plastic products, such as the Single Use Plastics Directive (SUPD) in Europe.

40 international speakers presented the latest market trends in their industry and illustrated the innovation potential of cellulose fibres. Leading experts introduced new technologies for the recycling of cellulose-rich raw materials and gave insights into circular economy practices in the fields of textiles, hygiene, construction and packaging. All presentations were followed by exciting panel discussions with active audience participation including numerous questions and comments from the audience in Cologne and online. Once again, the Cellulose Fibres Conference proved to be an excellent networking opportunity to the 214 participants and 23 exhibitors from 27 countries. The annual conference is a unique meeting point for the global cellulose fibre industry.  

For the fourth time, nova-Institute has awarded the “Cellulose Fibre Innovation of the Year” Award at the Cellulose Fibres Conference. The Innovation Award recognises applications and innovations that will lead the way in the industry’s transition to sustainable fibres. Close race between the nominees – “The Straw Flexi-Dress” by DITF & VRETENA (Germany), cellulose textile fibre from unbleached straw pulp, is the winning cellulose fibre innovation 2024, followed by HONEXT (Spain) with the “HONEXT® Board FR-B (B-s1, d0)” from fibre waste from the paper industry, while TreeToTextile (Sweden) with their “New Generation of Bio-based and Resource-efficient Fibre” won third place.

Prior to the event, the conference advisory board had nominated six remarkable innovations for the award. The nominees were neck and neck, when the winners were elected in a live vote by the audience on the first day of the conference.

First place
DITF & VRETENA (Germany): The Straw Flexi-Dress – Design Meets Sustainability
The Flexi-Dress design was inspired by the natural golden colour and silky touch of HighPerCell® (HPC) filaments based on unbleached straw pulp. These cellulose filaments are produced using environmentally friendly spinning technology in a closed-loop production process. The design decisions focused on the emotional connection and attachment to the HPC material to create a local and circular fashion product. The Flexi-Dress is designed as a versatile knitted garment – from work to street – that can be worn as a dress, but can also be split into two pieces – used separately as a top and a straight skirt. The top can also be worn with the V-neck front or back. The HPC textile knit structure was considered important for comfort and emotional properties.

Second place
Honext Material (Spain): HONEXT® Board FR-B (B-s1, d0) – Flame-retardant Board made From Upcycled Fibre Waste From the Paper Industry
HONEXT® FR-B board (B-s1, d0) is a flame-retardant board made from 100 % upcycled industrial waste fibres from the paper industry. Thanks to innovations in biotechnology, paper sludge is upcycled – the previously “worthless” residue from paper making – to create a fully recyclable material, all without the use of resins. This lightweight and easy-to-handle board boasts high mechanical performance and stability, along with low thermal conductivity, making it perfect for various applications in all interior environments where fire safety is a priority. The material is non-toxic, with no added VOCs, ensuring safety for both people and the planet. A sustainable and healthy material for the built environment, it achieves Cradle-to-Cradle Certified GOLD, and Material Health CertificateTM Gold Level version 4.0 with a carbon-negative footprint. Additionally, the product is verified in the Product Environmental Footprint.

Third Place
TreeToTextile (Sweden): A New Generation of Bio-based and Resource-efficient Fibre
TreeToTextile has developed a unique, sustainable and resource efficient fibre that doesn’t exist on the market today. It has a natural dry feel similar to cotton and a semi-dull sheen and high drape like viscose. It is based on cellulose and has the potential to complement or replace cotton, viscose and polyester as a single fibre or in blends, depending on the application.
TreeToTextile Technology™ has a low demand for chemicals, energy and water. According to a third party verified LCA, the TreeToTextile fibre has a climate impact of 0.6 kg CO2 eq/kilo fibre. The fibre is made from bio-based and traceable resources and is biodegradable.

The next conference will be held on 12-13 March 2025.

ACG Kinna Automatic and ACG Nyström – members of TMAS, the Swedish textile machinery association – have delivered the first microfactory for the production of fully finished filter bags to an international filtration industry customer, in cooperation with JUKI Central Europe.

The microfactory’s configuration is based on two separate interconnecting modules – the Smart Filter Line (SFL) and the Filtermaster 2.0. The SFL handles the fabric feeding from rolls and its folding prior to seam construction, which can either be by automatic sewing, welding or with sewing and taping, depending on specifications. Very rapid changeover of the modular seaming methods can be achieved during product changes. The specific size of the now fully-tubular fabric is then precisely cut to size for each individual unit and further folded ready to be fed into the Filtermaster 2.0. The Filtermaster 2.0 then automatically attaches the reinforcement, bottom and snap rings onto the filter tube with a second Juki sewing head on a robotic arm, to form the fully finished filter bag ready for packaging.

Filter bags are employed in a wide range of industrial processes and while they may be largely under the radar as products, they represent a pretty significant percentage of overall technical textiles production.
They are used in foundries, smelters, incinerators, asphalt plants and energy production plants. Other key manufacturing fields – often where dust is generated – include the production of timber, textiles, composites, waste handling and minerals, in addition to chemicals, food production, pharmaceuticals, electronics and agriculture.

As a further example of the scale of the industry and the high volumes of fabrics involved, one supplier has delivered a single order of 30,000 filter bags to be used for flue gas cleaning at a European power plant. The bags can also be anywhere up to twelve metres in length and frequently have to be replaced.

• Three out of four business units with record sales and results
• Carbon Fibers business weighs on the Group's profitability
• Group sales of €1,089.1 million (-4.1%) and adjusted EBITDA of €168.4 million (-2.5%) in a difficult market environment
• Sales and earnings forecast for 2023 achieved despite drop in demand from key market
• 2024 further capacity expansion in graphite components for silicon carbide-based semiconductors

In fiscal year 2023, SGL Carbon achieved the sales and earnings targets set at the beginning of the year despite the drop in demand from the important wind market and an increasingly challenging economic environment. Group sales decreased slightly by €46.8 million (minus 4.1%) to €1,089.1 million (previous year: €1,135.9 million). At € 168.4 million, adjusted EBITDA, a key performance indicator for the Group, was also down slightly (minus 2.5%) compared to the previous year (€172.8 million) but was clearly within the forecast range for 2023 of €160 to 180 million.

While the positive sales development of the Graphite Solutions (+€53.5 million to €565.7 million), Process Technology (+€21.6 million to €127.9 million) and Composite Solutions (+€0.8 million to €153.9 million) business units had a positive effect, the Carbon Fibers business unit had a negative impact on Group sales with a sales decline of €122.3 million to €224.9 million.

Outlook
The global economy will continue to face comparatively high interest rates and subdued growth prospects in 2024. Tighter financing conditions, weak trade growth and a decline in business and consumer confidence are also weighing on the economic outlook. In addition, heightened geopolitical tensions are contributing to increased uncertainty.

SGL Carbon expects different developments in our key sales markets in 2024. The most important sales and earnings driver will be demand for specialty graphite components for the semiconductor industry. In contrast, all indicators currently suggest that demand for carbon fibers for the wind industry will remain weak in 2024 and that the Carbon Fibers (CF) business unit will therefore continue to record operating losses. Even if demand picks up, SGL Carbon assumes that Carbon Fibers will require additional resources to make the most of market opportunities. With this in mind, teh company announced on February 23, 2024, that they are reviewing all strategic options for Carbon Fibers. These also include a possible partial or complete sale of the business unit.

SGL Carbon's sales forecast for the financial year 2024 takes all four operating business units into account, as the company is only at the beginning of evaluating the strategic options for CF. In line with the assumptions outlined, SGL Carbon is therefore expecting Group sales at the previous year's level (2023: €1,089.1 million).

In the earnings forecast, SGL Carbon has taken into account underutilization of production capacity in the Carbon Fibers business unit and the associated high idle capacity costs. The projected operating loss of CF will have a negative impact on the adjusted EBITDA of the SGL Carbon Group in 2024. Due to the expected positive development of Graphite Solutions, SGL Carbon anticipates an adjusted EBITDA of between €160 million and €170 million for fiscal year 2024, taking into account all four operating business units. Should the process of reviewing all strategic options for the CF business unit result in a sale, the forecast of adjusted EBITDA in 2024 would be between €180 - 190 million.

The DITF is leading the joint project "DACCUS-Pre*". The basic idea of the project is to develop a new building material that stores carbon in the long term and removes more CO₂ from the atmosphere than is emitted during its production.       

In collaboration with the company TechnoCarbon Technologies, the project is now well advanced - a first demonstrator in the form of a house wall element has been realized. It consists of three materials: Natural stone, carbon fibers and biochar. Each component contributes in a different way to the negative CO₂ balance of the material:

Two slabs of natural stone form the exposed walls of the wall element. The mechanical processing of the material, i.e. sawing in stone cutting machines, produces significant quantities of stone dust. This is very reactive due to its large specific surface area. Silicate weathering of the rock dust permanently binds a large amount of CO₂ from the atmosphere.

Carbon fibers in the form of technical fabrics reinforce the side walls of the wall elements. They absorb tensile forces and are intended to stabilize the building material in the same way as reinforcing steel in concrete. The carbon fibers used are bio-based, produced from biomass. Lignin-based carbon fibers, which have long been technically optimized at DITF Denkendorf, are particularly suitable for this application: They are inexpensive due to low raw material costs and have a high carbon yield. In addition, unlike reinforcing steel, they are not susceptible to oxidation and therefore last much longer. Although carbon fibers are more energy-intensive to produce than steel, as used in reinforced concrete, only a small amount is needed for use in building materials. As a result, the energy and CO₂ balance is much better than for reinforced concrete. By using solar heat and biomass to produce the carbon fibers and the weathering of the stone dust, the CO₂ balance of the new building material is actually negative, making it possible to construct CO₂-negative buildings.

The third component of the new building material is biochar. This is used as a filler between the two rock slabs. The char acts as an effective insulating material. It is also a permanent source of CO₂ storage, which plays a significant role in the CO₂ balance of the entire wall element.

From a technical point of view, the already realized demonstrator, a wall element for structural engineering, is well developed. The natural stone used is a gabbro from India, which has a high-quality appearance and is suitable for high loads. This has been proven in load tests.  Bio-based carbon fibers serve as the top layer of the stone slabs. The biochar from Convoris GmbH is characterized by particularly good thermal insulation values.

The CO₂ balance of a house wall made of the new material has been calculated and compared with that of conventional reinforced concrete. This results in a difference in the CO₂ balance of 157 CO₂ equivalents per square meter of house wall. A significant saving!

* (Methods for removing atmospheric carbon dioxide (Carbon Dioxide Removal) by Direct Air Carbon Capture, Utilization and Sustainable Storage after Use (DACCUS).

Lightweight design is a key enabler for addressing the energy transition and sustainable economy. Following the liquidation of the state agency Leichtbau BW GmbH, a consortium consisting of the Allianz Faserbasierter Werkstoffe Baden-Württtemberg (AFBW), the Leichtbauzentrum Baden-Württemberg (LBZ e.V. -BW) and Composites United Baden-Württemberg (CU BW) now represents the interests of the lightweight construction community in the State.

The Lightweight Design Agency for Baden-Württemberg is set up for this purpose on behalf of and with the support of the State. The Lightweight Construction Alliance BW is the central point of contact for all players in the field of lightweight construction in the State and acts in their interests at national and international level. Professor Markus Milwich from the German Institutes of Textile and Fiber Research Denkendorf (DITF) represents the agency.

The use of lightweight materials in combination with new production technologies will significantly reduce energy consumption in transportation, the manufacturing industry and the construction sector. Resources can be saved through the use of new materials. As a cross-functional technology, lightweight construction covers entire value chain from production and use to recycling and reuse.

The aim of the state government is to establish Baden-Württemberg as a leading provider of innovative lightweight construction technologies in order to strengthen the local economy and secure high-quality jobs.

Among others, the "Lightweight Construction Alliance Baden-Württemberg" will continue the nationally renowned "Lightweight Construction Day", which acts as an important source of inspiration for a wide range of lightweight construction topics among business and scientific community.

Professor Milwich, an expert with many years of experience and an excellent network beyond the State's borders, has been recruited for this task. In his role, Milwich also represents the state of Baden-Württemberg on the Strategy Advisory Board of the Lightweight Construction Initiative of the Federal Ministry for Economic Affairs and Climate Action, which supports the cross functional-technology and efficient transfer of knowledge between the various nationwide players in lightweight construction and serves as a central point of contact for entrepreneurs nationwide for all relevant questions.

From 2005 to 2020, Professor Milwich headed the Composite Technology research at the DITF, which was integrated into the Competence Center Polymers and Fiber Composites in 2020. He is also an honorary professor at Reutlingen University, where he teaches hybrid materials and composites. "Lightweight design is an essential aspect for sustainability, environmental and resource conservation. I always showcase this in research and teaching and now also as a representative of the lightweight construction community in Baden-Württemberg," emphasizes Professor Milwich.

In a move to enhance the global competitiveness of the Turkish apparel industry, the Istanbul Apparel Exporters' Association (IHKIB) has entered into a collaborative agreement with the Worldwide Responsible Accredited Production (WRAP).

IHKIB, representing 80% of Türkiye's apparel exports, aims to facilitate and guide its members in navigating new markets and staying abreast of sectoral developments.
WRAP, a US-based non-profit organization, focuses on promoting safe, lawful, humane, and ethical working conditions within the textile and apparel industry.

Mr. Selcuk Mehmet Kaya, Chairman of the International Relations and Sustainability Committee of IHKIB, and Mr. Avedis Seferian, President and CEO of WRAP, officially inked a collaboration agreement on March 8, 2024, marking a significant step towards fostering business relations between Türkiye and the USA. The agreement focuses on a pilot project developed by IHKIB and WRAP, aiming to identify leading Turkish apparel companies exporting to the USA and encouraging these facilities to attain WRAP certification. In return, WRAP will provide in-person and virtual training at no charge to guide these facilities through the certification process. The project seeks to strengthen business ties between Türkiye and the USA, creating additional opportunities for mutual cooperation between the parties in both countries.

Freudenberg Performance Materials (Freudenberg) is showcasing solutions for the automotive, building, apparel, filtration and packaging industries at this year’s Techtextil in Frankfurt am Main from April 23 – 26.

Sustainable nonwoven for car seats
One innovation highlight at Techtextil is a novel Polyester nonwoven material for car seat padding. Also available as a nonwoven composite with PU foam, it is not only easier for car seat manufacturers to handle during the mounting process, but also ensures better dimensional stability as well as providing soft and flexible padding. It has a minimum 25 percent recycled content, for example, by reusing nonwoven clippings and waste, and is fully recyclable. Full supply chain transparency enables customers to trace and verify the content of the nonwoven and thus ensures a responsible production process. The Freudenberg experts will also be presenting several other nonwoven solutions made of up to 80 percent recycled materials that can be used in car seat manufacturing.

Biocarrier for green roofs
Freudenberg is showcasing a sustainable carrier material for green roofs on urban buildings at the trade fair. The carrier is made from polylactide, i.e. from renewable resources. When filled with soil, it provides a strong foothold to root systems, enabling the growth of lightweight sedum blankets that can be rolled out to provide instant green roofs. These roofs not only help counter urban heat, they also improve stormwater management and regulate indoor temperatures.

From textile waste to padding
The company extended its circular thermal wadding product range with the release of comfortemp® HO 80xR circular, a wadding made from 70 percent recycled polyamide from discarded fishing nets, carpet flooring and industrial plastic. Because polyamide 6, also known as nylon, retains its performance characteristics after multiple recycling processes, the fibers can be used again and again to manufacture performance sporting apparel, leisurewear and luxury garments.

Packaging solutions with various sustainability benefits
Freudenberg is also showcasing products for sustainable packaging and filtration solutions. The long-lasting Evolon® technical packaging series is a substitute for disposable packaging used in the transport of sensitive industrial items such as automotive parts. The material is made from up to 85 percent recycled PET. A further highlight at Techtextil are Freudenberg’s fully bio-based solutions for manufacturing dessicant bags. The binder-free material based on bio-fibers is also industrially compostable.
In addition, the experts will be giving trade fair visitors an insight into Freudenberg’s filtration portfolio.

Turkey's leading garment machinery manufacturers and representatives have collaborated with Teknik Fuarcılık for GarmentTech İstanbul Garment, Embroidery Machines Spare Parts and Sub Industry Exhibition to host the first GarmentTech İstanbul Exhibition.

The GarmentTech İstanbul Exhibition will be held at İstanbul Expo Center (IFM) between June 25-28, 2025 and brings together all the technologies used in garment and ready-to-wear production.

The ready-to-wear and garment sector is among the locomotive sectors of the Turkish economy with both employment and export income. With 22 thousand 640 exporters and 42 thousand 434 manufacturers, the sector is among the priority sectors in the country's employment with approximately 700 thousand people working in production. Together with the retail and ready-to-wear sectors, total employment exceeds 2 million.

On the other hand, ready-to-wear and garment sector is the 3rd largest exporter in Turkey. Turkey is the 5th country in the world that exports the most ready-to-wear and garment. In 2023, the sector reached 19.3 billion dollars in exports and has a share of 7.5% in general exports.

Teknik Fuarcılık, which has more than 30 years of experience in exhibition organization and has made the ITM International Textile Machinery Exhibition a world brand, has taken action to make the success achieved by the garment and ready-to-wear sector sustainable. GarmentTech İstanbul Exhibition, which will be organized with the support of the members of the Garment Machinery Advisory Board and in cooperation with the Apparel Automation and Machinery Manufacturers Association (KOMİD), will host professional visitors and global buyers from all over the world.

The press conference of GarmentTech İstanbul Exhibition was attended by members of the Garment Machinery Advisory Board, Vice Chairman of Astaş Holding H. Kaya Aşçı, Astaş Juki Board Member and General Manager Turgay Aşçı, Chairman of the Board of Çatma Makine Yavuz Çatma, Chairman of the Board of Alba Makine Cengiz Albayrak, General Manager of Malkan Makine Alparslan Er, General Manager of Uğur Makine Temel Kamiloğlu, Tetaş Sales and Marketing Assistant General Manager Murat Eren, Malkan Makina Factory Manager Metin Kılıç and KOMID President Haluk Akın, TEMSAD President Adil Nalbant, KOMİD Members Serkon Makina Chairman İzzet Savaş, Robotech General Manager Hüseyin Çetin, Chairman of the Board of NewTech Machinery Nezir Yazıcı, LGM Foreign Trade Specialist Yiğit Sağdık Manav, Avtek Manager Oğuz Avcı and many sector representatives.

Mayer & Cie. CN Changzhou LLC, the Chinese subsidiary of the German circular knitting and braiding machine manufacturer Mayer & Cie., settled in Jiangsu Province at the beginning of the year. Until now, the Sales & Service subsidiary Mayer & Cie. China, founded in 2003 and later to become Mayer & Cie. China, had been based in Shanghai.

The new location within a Sino-German Innovation Park comprises a production hall of around 5,000 square meters. In the future, the circular knitting machines assembled for the domestic market will increasingly consist of locally sourced parts and components from various suppliers.

Since 2011, Mayer & Cie. has been assembling selected machine types for the domestic market at its Chinese plant in Shanghai. It started with a single jersey machine for the most common requirements. Today, China's domestic portfolio includes four types of machines. Until now, the knitting heads for these circular knitting machines had been pre-produced at the Mayer & Cie. plant in the Czech Republic and then transported to China.

The manufacturer is now saying goodbye to this "knitting head principle". It made perfect sense for the start of the assembly line, says Benjamin Mayer, managing partner of Mayer & Cie. However, it leaves little room for flexibility. He explains: "In the future, we will source all parts and components of the machines assembled in China from various local suppliers. This allows us to offer our local customers more attractive prices and faster delivery times with the same quality standards. We expect this change to improve the positioning of our products in the domestic market." In addition, the new plant will be connected to the parent company in Albstadt via an SAP connection. This was imperative to increase efficiency, transparency and quality.

The new headquarters of Mayer & Cie. CN is the German Chinese Innovation Park in Jintan in Jiangsu Province. The companies based there enjoy various advantages, including attractive location costs as well as proximity and exchange with other German companies on site. In addition, the administration of the SGIP supports companies in their search for employees, suppliers and service providers.