From the Sector

Reset
28 results
Prof. Dr Tae Jin Kang (Seoul National University), Dr Musa Akdere (CarboScreen), Dr Christian P. Schindler (ITMF), from left to right. Source: ITMF
Prof. Dr Tae Jin Kang (Seoul National University), Dr Musa Akdere (CarboScreen), Dr Christian P. Schindler (ITMF), from left to right.
01.12.2023

Faster and cheaper carbon fibre production with CarboScreen

Faster and more cost-effective carbon fibre production - the technology of the start-up CarboScreen comes a good deal closer to this dream. The founders Dr. Musa Akdere, Felix Pohlkemper and Tim Röding from the Institut für Textiltechnik (ITA) of RWTH Aachen University are using sensor technology to monitor carbon fibre production, thereby doubling the production speed from the current 15 to 30 m/min in the medium term and increasing turnover by up to €37.5 million per year and system. This ground-breaking development also impressed the jury at the ITMF at their Annual Conference in Keqiao, China, and was honoured with the ITMF StartUp Award 2023 on 6 November 2023.

Dr. Musa Akdere accepted the award on behalf of the CarboScreen founding team.

Carbon fibres can only develop their full potential if they are not damaged during production and further processing. Two types of fibre damage occur more frequently during fibre production: Superficial or mechanical damage to the fibres or damage to the chemical structure.

Faster and more cost-effective carbon fibre production - the technology of the start-up CarboScreen comes a good deal closer to this dream. The founders Dr. Musa Akdere, Felix Pohlkemper and Tim Röding from the Institut für Textiltechnik (ITA) of RWTH Aachen University are using sensor technology to monitor carbon fibre production, thereby doubling the production speed from the current 15 to 30 m/min in the medium term and increasing turnover by up to €37.5 million per year and system. This ground-breaking development also impressed the jury at the ITMF at their Annual Conference in Keqiao, China, and was honoured with the ITMF StartUp Award 2023 on 6 November 2023.

Dr. Musa Akdere accepted the award on behalf of the CarboScreen founding team.

Carbon fibres can only develop their full potential if they are not damaged during production and further processing. Two types of fibre damage occur more frequently during fibre production: Superficial or mechanical damage to the fibres or damage to the chemical structure.

Both types of damage cannot be optimally detected by current means or only become apparent after production, to name just two examples. This leads to higher production costs. In an emergency, faulty production can even lead to plant fires. For this reason, and to ensure good production quality, the system is run at 15 m/min below its production capacity for safety reasons. However, 30 m/min or more would be possible. With the sensor-based online monitoring of CarboScreen, the production capacity can be doubled to 30 /min. This would lead to higher production, resulting in lower manufacturing costs and wider use of carbon fibres in mass markets such as automotive, aerospace and wind energy.

More information:
carbon fibers sensors Startup
Source:

ITA – Institut für Textiltechnik of RWTH Aachen University
 

ITMA Asia + CITME Photo: Swissmem
01.11.2023

15 member companies of Swiss Textile Machinery Association at upcoming ITMA Asia + CITME

In China, the textile industry is forward-looking and resilient – with a healthy appetite for new technologies and a determination to keep its leading position. Sustainability is increasingly coming into focus, so there is a growing demand for recycling technologies, as well as automated solutions and digitalization. Cornelia Buchwalder, Secretary General of the Swiss Textile Machinery Association, is clear: “China is the main market for a large number of our association members.” On top of growing consumer demand and technological capabilities, the latest ambitious five-year plan will drive further development of the Chinese textile industry in world markets, and Swiss companies will work with all stakeholders to enable its success.

In China, the textile industry is forward-looking and resilient – with a healthy appetite for new technologies and a determination to keep its leading position. Sustainability is increasingly coming into focus, so there is a growing demand for recycling technologies, as well as automated solutions and digitalization. Cornelia Buchwalder, Secretary General of the Swiss Textile Machinery Association, is clear: “China is the main market for a large number of our association members.” On top of growing consumer demand and technological capabilities, the latest ambitious five-year plan will drive further development of the Chinese textile industry in world markets, and Swiss companies will work with all stakeholders to enable its success.

Market proximity
Swiss companies realized many years ago that geographical proximity is the key to success. Stäubli has started to set up offices in Chinese cities since 1998 and counts 12 locations today, to serve the whole country. In 2002, Itema established a centralized local branch which today has 160 employees in various functions. Loepfe has expanded its presence by creating an independent local business unit to overcome the 9,000 km distance by air, while Uster Technologies has had a Chinese subsidiary since 1982, with offices and service stations in different provinces. Luwa set up its offices and workshop in Shanghai in 1997. Rieter established a presence in mainland China in 2005, driven by a strong commitment to expanding the country’s know-how and expertise – and ten years later opened an advanced research center. All Swiss companies with serious business goals in China have made similar commitments to connect with customers and maintain strong relationships.

Understanding Chinese customers
Swiss companies also understand that Chinese customers require dedicated attention, and that speed is more essential than ever in delivering both machines and services.
Manufacturers in China are seeking cost-effective solutions to remain competitive, while consumers are looking for value in their purchases. Companies need to develop solutions that provide tangible economic benefits to their clients. Furthermore, energy savings have become paramount in China, due to the government's commitment to environmental sustainability and reduced carbon emissions. “Businesses are adopting more energy-efficient processes and technologies to meet stringent energy conservation and emission reduction targets,” says Peter Schnickmann, Managing Director at Luwa Air Engineering (Shanghai). He notes an investment trend for solutions helping Chinese companies cut operational costs and minimize their carbon footprint.

To enhance the reputation of both companies and products – and boost the image of the entire industry – the environmental impact needs to decrease. Priorities are saving water and waste, as well as reducing, replacing or completely eliminating the use of harmful substances. China has a strong demand for environmental-friendly solutions and sustainable technologies.

Customer-oriented in weaving
The huge number of Chinese fabric producers calls for an immense volume of weaving machinery to be supplied by international and local providers. Swiss machinery manufacturers hold an impressive share of this business.
Chinese weavers require advanced technology, with increasingly higher standards of efficiency. In weaving preparation, latest solutions match the speed, quality and reliability now wanted. Weaving machines too offer the eco-efficiency, performance, and ease of use needed, with innovations that extend the scope of sustainable weaving, and open-platform systems configurable to weavers’ specific operations. A huge increase in demand for technical textiles in recent years has been driven by applications such as carbon fiber, aramid and glass fiber.

Profitable in spinning
China’s competitive advantages come from its large-scale and integrated manufacturing capabilities, along with the use of advanced automation and digitization technologies. Spinners aim to capitalize on extended market opportunities, with more economical production. The latest air-jet spinning machines serve these goals, allowing exceptionally low production costs per kilogram of yarn, coupled with high flexibility and reliability. Sustainable yarns are in great demand.

The automation trend in spinning mills focuses on connecting production processes. Data is used to ensure the highest quality standards, most efficient raw material usage, reduction of waste, and energy savings. To make spinning mills more competitive, latest solutions combine cutting-edge hardware, data-enabled software and renowned textile expertise.

More information:
ITMA Asia + CITME Swissmem
Source:

Swissmem

Photo: ANDRITZ
12.04.2023

Lotus Teknik Tekstil A.Ş.: Production line for biodegradable wet wipes by ANDRITZ

Lotus Teknik Tekstil A.Ş., Türkiye, has successfully started up a complete line to produce nonwoven roll goods for biodegradable, plastic-free wet wipes. This line has been delivered, installed, and commissioned by international technology group ANDRITZ.

The neXline wetlace CP line combines the benefits of two technologies: wetlaid and spunlace. Natural fibers are processed gently to create a high-performance and sustainable wipe. This next-generation wipe, called Newipe®, combines the benefits of spunlace fabric, in particular remarkable strength in all directions, with the biodegradability and softness of a WetlaceTM fabric. It is produced with a lower carbon footprint, has a low lint rate, and does not generate dust during production.

Lotus Teknik Tekstil A.Ş., Türkiye, has successfully started up a complete line to produce nonwoven roll goods for biodegradable, plastic-free wet wipes. This line has been delivered, installed, and commissioned by international technology group ANDRITZ.

The neXline wetlace CP line combines the benefits of two technologies: wetlaid and spunlace. Natural fibers are processed gently to create a high-performance and sustainable wipe. This next-generation wipe, called Newipe®, combines the benefits of spunlace fabric, in particular remarkable strength in all directions, with the biodegradability and softness of a WetlaceTM fabric. It is produced with a lower carbon footprint, has a low lint rate, and does not generate dust during production.

Lotus Teknik Tekstil A.Ş. is a leading nonwoven roll good producer and a member of a group company. The group company consists of 4 companies that operate end-to-end manufacturing including nonwovens, cardboard packings, plastics, and finished wet wipe products. Headquartered in Istanbul, Sapro is the leader in Türkiye and one of the four leaders in the manufacturing of wet wipes in Europe. The company produces, converts, and supplies 161 million sheets of wipes per day for personal, household, and industrial use, exporting 70% of its production to 65 countries all over the world. Sustainability plays a prominent role in Sapro’s business strategy.

Source:

ANDRITZ AG

(c) M. Vorhof, ITM/TU Dresden
12.04.2023

ITM at JEC 2023

From April 25th to 27th, 2023, the Institute of Textile Machinery and High Performance Material Technology (ITM) of TU Dresden will be exhibiting at the pavilion SAXONY! at JEC World 2023.

The ITM will provide a comprehensive overview of its current research in the field of machine and product development along the entire textile process chain.

The upcoming JEC 2023 exhibition will highlight innovative Customised Connective Cores (CCC), which are custom-made core-insert structures additively manufactured using cellular metal and a form-fit integrated insert. These CCCs can be seamless integrated either as patches or as full-surface core material into lightweight panels, offering significantly improved load-bearing behavior (especially 4 times the load-bearing capacity and fail-safe behavior) compared to existing technologies. This breakthrough opens up new possibilities for fastening lightweight panels.

From April 25th to 27th, 2023, the Institute of Textile Machinery and High Performance Material Technology (ITM) of TU Dresden will be exhibiting at the pavilion SAXONY! at JEC World 2023.

The ITM will provide a comprehensive overview of its current research in the field of machine and product development along the entire textile process chain.

The upcoming JEC 2023 exhibition will highlight innovative Customised Connective Cores (CCC), which are custom-made core-insert structures additively manufactured using cellular metal and a form-fit integrated insert. These CCCs can be seamless integrated either as patches or as full-surface core material into lightweight panels, offering significantly improved load-bearing behavior (especially 4 times the load-bearing capacity and fail-safe behavior) compared to existing technologies. This breakthrough opens up new possibilities for fastening lightweight panels.

Another highlight at the exhibition is the repair process for fibre-reinforced composites (FRP) developed at the ITM. Instead of mechanically grinding the damaged area, the matrix in the repair area is locally dissolved using a UV-rays-induced depolymerisation process. Damaged fibres can thus be replaced by a customized repair patch. Free yarn ends on the textile repair patches are spliced with the UV-exposed yarn ends in the repair area using an adapted splicing process. In this way, a very clean, simplified and mechanically improved repair area can be achieved compared to the state of the art.

The diverse possibilities offered by the structure and process simulation of textile high-performance materials and textile manufacturing processes will also be presented. By means of multi-scale modelling and simulation, a profound understanding of materials and processes is achieved at the ITM. Finite element models on the micro, meso and macro scale have been developed and validated for this purpose. Examples from current ITM research projects demonstrate the various possibilities and areas of application of modern simulation methods in the field of textile technology.

Moreover, an innovative process for the integral manufacturing of 3D rib-stiffened preforms with complexly arranged stiffeners in 0°, 90° and ± 45° orientation was developed and successfully implemented at the ITM. Due to the process-integrated structure fixation and the continuous fibre reinforcement between shell and rib structure, the 3D preforms are perfectly suited for the production of highly load-bearing FRP components with increased bending stiffness, which will be exhibited at JEC. Hence, the lightweight construction potential of high-performance fibres can be fully exploited.

A successfully established development are partially flowable 2D textile reinforcement fabrics that are continuously manufactured in one single process step. For this purpose, the entire process chain was developed at the ITM, which allows a cost-effective and high-volume production of load-bearing thermoplastic 3D FRP components with continuous fibre reinforcement between shell and stiffeners.

At JEC 2023, the ITM will also present a partially embedded textile latice girder as reinforcement for carbon concrete applications, which was produced by means of an innovative textile manufacturing process based on the multiaxial warp knitting technology. Through the development of a customized warp insertion, manipulation and take-off system as well as appropriate shaping methods, it is now possible to produce tailored textile semi-finished products, e.g. for use in wall and ceiling panels. These textile latice girders represent a resource-saving alternative to conventional steel girders due to the reduced among of concrete required and the additional cavity for media and cable guidance.

The integration of textile actuators and sensors in FRP provides structures with additional functionalities. The research and application of such interactive FRP with different matrix materials (e.g. with thermoset, elastomer or concrete matrix systems) for structural health monitoring or adaptive systems is one of the key research areas of the ITM.

Moreover, the development and implementation of innovative yarn constructions based on recycled high-performance fibres (e.g. rCF, rGF, rAR) for sustainable FRPs is successfully promoted at ITM. By use of a special carding machine, recycled fibres are opened up, separated and joined to form a wide, uniform ribbon. Subsequently, innovative hybrid yarn constructions made of evenly mixed recycled high-performance and thermoplastic fibres with variable fibre volume fractions can be manufactured by means of various spinning technologies. Selected yarn constructions and components will be showcased at JEC.

More information:
ITM TU Dresden JEC World
Foto: ANDRITZ
Novafiber CEO and Head of Production together with ANDRITZ technicians and project manager in front of the newly installed 6-cylinder EXEL line
05.04.2023

Novafiber starts up textile recycling and airlay lines from ANDRITZ

International technology group ANDRITZ has delivered, installed, and commissioned a mechanical textile recycling line and an airlay line at Novafiber’s nonwovens production mill in Palín, Guatemala. Both lines have been successfully operating since December 2022.

The recycling line – the second tearing line ANDRITZ supplied to Novafiber – processes post-industrial textile waste from Central America. The recycled fibers feed the latest ANDRITZ Flexiloft airlay line, which produces nonwoven end-products for the bedding and furniture industries – a true example of a circular textile-to-nonwoven approach. The production process ensures complete material use as a state-of-the-art edge trim recycling system returns any waste directly to the tearing and/or airlay line.

This combination of ANDRITZ tearing and airlay lines allows Novafiber to process large amounts of post-industrial garments, controlling the supply chain from raw material to final product. In addition, it enables energy savings and a reduced carbon footprint due to the reduction of shipments.

International technology group ANDRITZ has delivered, installed, and commissioned a mechanical textile recycling line and an airlay line at Novafiber’s nonwovens production mill in Palín, Guatemala. Both lines have been successfully operating since December 2022.

The recycling line – the second tearing line ANDRITZ supplied to Novafiber – processes post-industrial textile waste from Central America. The recycled fibers feed the latest ANDRITZ Flexiloft airlay line, which produces nonwoven end-products for the bedding and furniture industries – a true example of a circular textile-to-nonwoven approach. The production process ensures complete material use as a state-of-the-art edge trim recycling system returns any waste directly to the tearing and/or airlay line.

This combination of ANDRITZ tearing and airlay lines allows Novafiber to process large amounts of post-industrial garments, controlling the supply chain from raw material to final product. In addition, it enables energy savings and a reduced carbon footprint due to the reduction of shipments.

Based in Palín, Novafiber is a leading company in Guatemala for producing nonwovens from post-industrial textile waste for both the local market and export.

Source:

ANDRITZ AG

(c) TMAS
30.12.2022

Climate impact mapping of Swedish textile machinery

Over the past year, TMAS, the Swedish Textile Machinery Association, has been working with ClimatePartner on a corporate carbon footprint (CCF) mapping project with its member companies, as a natural step towards supporting a more sustainable textile industry.

Over half of the members of TMAS are participating in the project, which involves calculating each operation’s Scope 1, 2 and 3 emissions in order to identify the current climate impact and areas where reductions can be made.

“Integrating climate action into strategies is becoming increasingly important in Europe and we have decided to take a pro-active role,” says TMAS secretary general Therese Premler-Andersson. “There is growing pressure from customers to be more transparant in this area and forthcoming legislation will soon make it necessary for all to take climate actions. TMAS members, however, recognise the benefit of taking action now, not least in terms of taking responsibility and demonstrating credibility.”

The CCF project’s scope examines all aspects of a business split into five areas:

Over the past year, TMAS, the Swedish Textile Machinery Association, has been working with ClimatePartner on a corporate carbon footprint (CCF) mapping project with its member companies, as a natural step towards supporting a more sustainable textile industry.

Over half of the members of TMAS are participating in the project, which involves calculating each operation’s Scope 1, 2 and 3 emissions in order to identify the current climate impact and areas where reductions can be made.

“Integrating climate action into strategies is becoming increasingly important in Europe and we have decided to take a pro-active role,” says TMAS secretary general Therese Premler-Andersson. “There is growing pressure from customers to be more transparant in this area and forthcoming legislation will soon make it necessary for all to take climate actions. TMAS members, however, recognise the benefit of taking action now, not least in terms of taking responsibility and demonstrating credibility.”

The CCF project’s scope examines all aspects of a business split into five areas:

  • Facility Management (heating, electricity, water, cooling agents and waste disposal).
  • Employee Mobility (commuting and company cars).
  • Business Travel (flights travel by train, rental cars).
  • Procurement (production, packaging and office materials).
  • Logistics (inbound and outbound).

Primary data is being used wherever possible and emission factors originate from internationally recognised databases such as ecoinvent and GEMIS.

The ClimatePartner measurement programme is based on the guidelines of the Greenhouse Gas Protocol Corporate Accounting and Reporting Standard (GHG Protocol), and factors in all greenhouse gases covered by the Kyoto Protocol. These are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), hydrofluorocarbons (HFC), perfluorocarbons (PFC), sulphur hexafluoride (SF6) and nitrogen trifluoride (NF3).

Each of these gases affect the atmosphere differently and remain in the atmosphere for different lengths of time. Rather than reporting on each gas separately, they are expressed as a CO2 equivalent (CO2e) for the sake of simplicity. A CO2e is essentially a conversion into a ‘global warming potential’ value that enables the influence of different gases on global warming to be compared.

Photo VDMA
12.12.2022

Young Talent Award for AI supported production control of carbon fibres

  • Formula 1 cars will be cheaper in future

Carbon is the stuff Formula 1 cars are made of, at least the bodywork. But until now, carbon has been expensive. It can be produced more cheaply and efficiently if artificial intelligence monitors the production processes. A camera system combined with artificial intelligence automatically detects defects in the production of carbon fibres. This makes expensive manual inspection of the carbon fibres obsolete and the production price of the carbon fibre can be reduced in the long term.

For this idea, the young engineer Deniz Sinan Yesilyurt received the second prize of the "Digitalisation in Mechanical Engineering" Young Talent Award on 6 December.

  • Formula 1 cars will be cheaper in future

Carbon is the stuff Formula 1 cars are made of, at least the bodywork. But until now, carbon has been expensive. It can be produced more cheaply and efficiently if artificial intelligence monitors the production processes. A camera system combined with artificial intelligence automatically detects defects in the production of carbon fibres. This makes expensive manual inspection of the carbon fibres obsolete and the production price of the carbon fibre can be reduced in the long term.

For this idea, the young engineer Deniz Sinan Yesilyurt received the second prize of the "Digitalisation in Mechanical Engineering" Young Talent Award on 6 December.

Carbon fibres are sought after because of their good properties. They are very light - they weigh up to 50 percent less than aluminium. The combination of low weight and good mechanical properties offers many advantages. Especially in times of the energy transition, lightweight materials like carbon are more relevant than ever before. At the same time, carbon fibres are as resistant to external stresses as metals. However, achieving these good properties of carbon fibres is very complex.


Up to 300 individual fibre strands - bundles of individual fibres - have to be monitored simultaneously during production. If carbon fibres tear, it costs time and money to sort out the damaged fibres. This is just one example of various defects that can occur in the fibres during production.


Therefore, Deniz Sinan Yesilyurt attached a camera to the carbon fibre line that takes pictures of various fibre defects during production and collects them in a database. The artificial intelligence in the camera's information technology system evaluates the fibre defects by assigning the images to predefined reference defects. In doing so, it recognises various fibre defects with a classification accuracy of 99 per cent. The process can also be used in other areas that produce chemical fibres.

Deniz Sinan Yesilyurt received the prize from the German Engineering Federation (VDMA) in Frankfurt am Main, Germany. He is a Bachelor's graduate at the Institut für Textiltechnik (ITA) of RWTH Aachen University. The full title of his bachelor's thesis is: "Development of a Kl-supported process monitoring using machine learning to detect fibre damage in the stabilisation process". The VDMA awarded the prize to a total of four theses from different universities. The prize is awarded for outstanding theses and was offered in Germany, Austria and Switzerland.

Source:

ITA – Institut für Textiltechnik of RWTH Aachen Universit

FET-200LAB wet spinning system Photo: Fibre Extrusion Technology Limited (FET)
21.11.2022

FET wet spinning system selected for major fibre research programme

Fibre Extrusion Technology Limited (FET) of Leeds, England has installed a FET-200LAB wet spinning system at the University of Manchester which will play a major part in advanced materials research to support sustainable growth and development.

This research programme will be conducted by The Henry Royce Institute, which operates as a hub model at The University of Manchester with spokes at other leading research universities in the UK.

The Henry Royce Institute identifies challenges and stimulates innovation in advanced UK materials research, delivering positive economic and societal impact. In particular, this materials research initiative is focused on supporting and promoting all forms of sustainable growth and development.
These challenges range from biomedical devices through to plastics sustainability and energy-efficient devices; hence supporting key national targets such as the UK’s zero-carbon 2050 target.

Fibre Extrusion Technology Limited (FET) of Leeds, England has installed a FET-200LAB wet spinning system at the University of Manchester which will play a major part in advanced materials research to support sustainable growth and development.

This research programme will be conducted by The Henry Royce Institute, which operates as a hub model at The University of Manchester with spokes at other leading research universities in the UK.

The Henry Royce Institute identifies challenges and stimulates innovation in advanced UK materials research, delivering positive economic and societal impact. In particular, this materials research initiative is focused on supporting and promoting all forms of sustainable growth and development.
These challenges range from biomedical devices through to plastics sustainability and energy-efficient devices; hence supporting key national targets such as the UK’s zero-carbon 2050 target.

FET-200 Series wet spinning systems complement FET’s renowned range of melt spinning equipment. The FET-200LAB is a laboratory scale system, which is especially suitable for the early stages of formulation and process development. It is used for processing new functional textile materials in a variety of solvent and polymer combinations.

In particular, the FET-200LAB will be utilised in trials for a family of fibres made from wood pulp, a sustainable resource rather than the usual fossil fuels. Bio-based polymers are produced from biomass feedstocks such as cellulose and are commonly used in the manufacture of high end apparel. The key to cellulose and other materials like lyocell and viscose is that they can be recycled, treated and fed back into the wet spinning system for repeat manufacture.

Established in 1998, FET is a leading supplier of laboratory and pilot melt spinning systems with installations in over 35 countries and has now successfully processed more than 35 different polymer types in multifilament, monofilament and nonwoven formats.

Source:

DAVID STEAD PROJECT MARKETING LTD

(c) Robin Inizan – Lucas Pavy Production
Tearing line by ANDRITZ in operation at the Renaissance Textile plant
11.11.2022

Renaissance Textile starts up the first textile recycling line by ANDRITZ in France

Renaissance Textile in Laval, France has successfully started up a complete textile recycling line, delivered, installed, and commissioned by ANDRITZ Laroche, part of the international technology group ANDRITZ.

The ANDRITZ textile recycling equipment enabled Renaissance Textile to become the first French recycling platform dedicated to industrial end-of-life textiles. The project aims to produce new fibers from the collected post-consumer apparel, which will be used to weave new recycled fabrics in the end.

The new 12,000 m² plant is equipped with a complete tearing line whose design is the result of close collaboration between R&D specialists from ANDRITZ Laroche and Renaissance Textile, as well as customized trials carried out jointly by the two parties at the ANDRITZ technical center in Cours, France.

Renaissance Textile in Laval, France has successfully started up a complete textile recycling line, delivered, installed, and commissioned by ANDRITZ Laroche, part of the international technology group ANDRITZ.

The ANDRITZ textile recycling equipment enabled Renaissance Textile to become the first French recycling platform dedicated to industrial end-of-life textiles. The project aims to produce new fibers from the collected post-consumer apparel, which will be used to weave new recycled fabrics in the end.

The new 12,000 m² plant is equipped with a complete tearing line whose design is the result of close collaboration between R&D specialists from ANDRITZ Laroche and Renaissance Textile, as well as customized trials carried out jointly by the two parties at the ANDRITZ technical center in Cours, France.

The new clothing produced based on this type of circular economy model thus reflects the social and sustainability commitments of Renaissance Textile in terms of decarbonizing the textile industry, the fight against global warming, autonomy in raw material sourcing, and promotion of local staffing, particularly for people who have been unemployed for a long time or are seeking to enter the labor market for the first time. By 2025, for example, Renaissance Textile plans to create no less than 110 direct jobs.

Freudenberg´s gas diffusion layer production Photo: Freudenberg´s gas diffusion layer production.
20.10.2022

Freudenberg supplies gas diffusion layers for fuel cell stacks

Freudenberg Performance Materials (Freudenberg) has concluded a high-volume, multi-year contract with a global automotive tier one supplier to supply high-performance gas diffusion layers for the stacks forming the core of the fuel cell systems produced by the leading automotive supplier. Global target applications are mid-sized and heavy commercial vehicles as well as buses. Freudenberg is supporting the customer’s global fuel cell activities, thereby also accelerating the breakthrough of mass-produced fuel cell stacks.

Fuel cell technology is an important element of a successful energy transition. Gas diffusion layers play a key role in this context: they are indispensable for the functioning of a fuel cell and have a significant impact on the performance of a fuel cell stack.

Freudenberg Performance Materials (Freudenberg) has concluded a high-volume, multi-year contract with a global automotive tier one supplier to supply high-performance gas diffusion layers for the stacks forming the core of the fuel cell systems produced by the leading automotive supplier. Global target applications are mid-sized and heavy commercial vehicles as well as buses. Freudenberg is supporting the customer’s global fuel cell activities, thereby also accelerating the breakthrough of mass-produced fuel cell stacks.

Fuel cell technology is an important element of a successful energy transition. Gas diffusion layers play a key role in this context: they are indispensable for the functioning of a fuel cell and have a significant impact on the performance of a fuel cell stack.

A fuel cell converts the chemical energy of hydrogen and atmospheric oxygen into electricity. Functionally-optimized gas diffusion layers made of carbon-fiber based nonwoven are installed on both sides of a catalyst-coated membrane positioned in the middle of the fuel cell. The gas diffusion layers distribute hydrogen and oxygen evenly to the membrane and remove the electricity, heat and water generated by the CO2-free chemical reaction. They also protect the sensitive membrane and are optimized to suit the bipolar plate. A fuel cell stack is made up of several individual fuel cells.

Freudenberg already has more than 20 years of unique expertise in the development and production of gas diffusion layers for fuel cell applications in the mobility sector and for porous transport layers used in electrolyzers. Freudenberg is currently expanding its production capacity at its Weinheim headquarters by installing additional lines. Further investments are on the verge of implementation.

Photo: ACIMIT
13.07.2022

Italian textile machinery sector returning to pre-Covid levels

  • Annual assembly of ACIMIT, the Association of Italian Textile Machinery Manufacturers

  • Digitalization and Sustainability Key to Resiliency for Italian Textile Machinery Sector

The objective critical issues faced by Italy as a whole throughout the course of 2021, primarily dictated by a pandemic that upset any and all pre-existing equilibriums, have not slowed or halted the Italian textile machinery sector.

Indeed, data presented during the annual assembly of ACIMIT, the Association of Italian Textile Machinery Manufacturers, held on 1 July proved decidedly positive, showing that in 2021 the sector recovered significantly compared to 2020, to the point of returning to pre-Covid levels.

Specifically, Italian textile machinery production amounted to 2.388 billion euros (+35% over 2020 and + 5% over 2019), with total exports amounting to 2.031 billion euros (+37% over 2020 and +9% over 2019).

  • Annual assembly of ACIMIT, the Association of Italian Textile Machinery Manufacturers

  • Digitalization and Sustainability Key to Resiliency for Italian Textile Machinery Sector

The objective critical issues faced by Italy as a whole throughout the course of 2021, primarily dictated by a pandemic that upset any and all pre-existing equilibriums, have not slowed or halted the Italian textile machinery sector.

Indeed, data presented during the annual assembly of ACIMIT, the Association of Italian Textile Machinery Manufacturers, held on 1 July proved decidedly positive, showing that in 2021 the sector recovered significantly compared to 2020, to the point of returning to pre-Covid levels.

Specifically, Italian textile machinery production amounted to 2.388 billion euros (+35% over 2020 and + 5% over 2019), with total exports amounting to 2.031 billion euros (+37% over 2020 and +9% over 2019).

However, these results do not cancel the obstacles that companies are still facing. Looking to the near future, expectations are for a rather uncertain outlook, as underscored by ACIMIT President Alessandro Zucchi: “2022 remains a year replete with unknown factors, starting with the Russian-Ukrainian conflict, along with the persistence of the pandemic, which seriously risk delaying expected growth consolidation for businesses in the sector. Difficulties in finding raw materials and components negatively affect the completion and fulfilment of orders processed as far back as 2021. To boot, rising energy costs and inflationary trends affecting numerous commodities are depressing overall business confidence. So the outlook for the sector is not so good.”
As such, the two cornerstones through which ACIMIT aims to support the Italian textile machinery sector are digitilization and sustainability.

4.0: The textile machinery sector looks to the future
The road to digital transformation has already led numerous manufacturers to completely rethink their production processes, rendering them more efficient and l ess expensive. The digital world is moving ahead at a decisive rate in the textile machinery sector, where the buzzwords are increasingly, for instance, the Internet of Things connecting to a company’s ecosystem, machine learning algorithms applied to production, predictive maintenance, and the integrated cloud management of various production departments. It is no coincidence that ACIMIT has focused decisively on its Digital Ready project, through which Italian textile machinery that adopt a common set of data are certified, with the aim of facilitating integration with the operating systems of client companies (ERP, MES, CRM, etc.).

A green soul
Combining production efficiency and respect for the environment: a challenge ACIMIT has made its own and which it promotes among its members through the Sustainable Technologies project. Launched by the association as early as 2011, the project highlights the commitment of Italian textile machinery manufacturers in the area of sustainability. At the heart of the project is the Green Label, a form of certification specifically for Italian textile machinery which highlights its energy and environmental performance. An all-Italian seal of approval developed in collaboration with RINA, an international certification body.
The assembly held on 1 July provided an opportunity to take stock of the Sustainable Technologies project, more specifically, with the presentation of the Rina Consulting survey on the Green Label’s evolution and impact in recent years.

The results have confirmed the initiative’s extreme validity. The technological advances implemented by the association’s machinery producers participating in the project have effectively translated into benefits in terms of environmental impact (reduction of CO2 equivalent emissions for machinery), as well as economic advantages for machinery users.

With reference to the year 2021, a total of 204,598 tons of CO2 emissions avoided on an annual basis have been quantified, thanks to the implementation of improvements on machinery. This is a truly significant reduction which, for the sake of comparison, corresponds to the carbon dioxide emissions generated by 36,864 automobiles travelling an average of 35,000 km a year. In terms of energy savings, the use of green labeled textile machinery has provided excellent performances in allowing for a reduction of up to 84% in consumption.

A round table discussion on the Green Label’s primary purpose
The environmental and economic impact generated in production processes for Italian textile machinery through the use of Green Label technologies was the focus of the round table which concluded the ACIMIT assembly.

Moderated by Aurora Magni (professor of the Industrial Systems Sustainability course at the LIUC School of Engineering), the debate involved Gianluca Brenna (Lipomo Printing House administrator and Vice President of the Italian Fashion System for Welfare), Pietro Pin (Benetton Group consultant and President of UNI for the textile-clothing area), Giorgio Ravasio (Italy Country Manager for Vivienne Westwood), as well as ACIMIT President Alessandro Zucchi.

Called on to compare common factors in their experiences relating to environmental transition processes for their respective companies, the participants were unanimous: the future of Italian textile machinery can no longer ignore advanced technology developments capable of offering sustainable solutions with a low environmental impact while also reducing production costs. This philosophy has by now been consolidated, and has proven to lead directly to a circular economy outlook.

The upcoming ITMA 2023 exhibition
Lastly, a word on ITMA 2023, the most important international exhibition for textile machinery, to be held in Italy from 8 to 14 June 2023 at Fiera-Milano Rho. Marking the 19th edition of ITMA, this trade fair is an essential event for the entire industry worldwide, providing a global showcase for numerous innovative operational solutions on display. A marketplace that offers participants extraordinary business opportunities. The participation of Italian companies is managed by ACIMIT.

Photo: © 2022, Steiger Participations
11.07.2022

Swiss Textile Machinery technology and innovations for technical textiles

New ideas were exchanged, brainstormed, and discussed freely at members’ booths at the Swiss Textile Machinery Pavilion during the recent Techtextil in Frankfurt. “Customers and researchers met Swiss textile machinery companies to explore the possibility of the not-yet-invented. “We regard our Pavilion as the place where future innovations catch a spark,” says Cornelia Buchwalder, Secretary General of the Swiss Textile Machinery Association. Further developments in the field of hybrid yarns were a hot topic. One example of this involves producing a yarn which has all the typical characteristics and advantages of carbon – but which also prioritizes careful use of resources, combining carbon fibres with thermoplastics.

Technical textiles cover a vast range of applications, and it’s still growing thanks to intensive research by specialist institutes and universities. Many members of the Swiss Textile Machinery Association maintain long-standing partnership with such bodies. Innovations are often joint efforts.

New ideas were exchanged, brainstormed, and discussed freely at members’ booths at the Swiss Textile Machinery Pavilion during the recent Techtextil in Frankfurt. “Customers and researchers met Swiss textile machinery companies to explore the possibility of the not-yet-invented. “We regard our Pavilion as the place where future innovations catch a spark,” says Cornelia Buchwalder, Secretary General of the Swiss Textile Machinery Association. Further developments in the field of hybrid yarns were a hot topic. One example of this involves producing a yarn which has all the typical characteristics and advantages of carbon – but which also prioritizes careful use of resources, combining carbon fibres with thermoplastics.

Technical textiles cover a vast range of applications, and it’s still growing thanks to intensive research by specialist institutes and universities. Many members of the Swiss Textile Machinery Association maintain long-standing partnership with such bodies. Innovations are often joint efforts.

Feel-good technical fabrics
Some technical textiles feel like a second skin. A well-known example is activewear from the ‘sport tech’ field. Activewear includes breathable clothing, usually consisting of a three-layer-laminate: an inner lining, a breathable membrane in the center, and an outer fabric. The challenge is to bond the individual layers without losing breathability or softness, while meeting technical requirements such as resistance to a number of wash cycles.

Bonding solutions meeting top quality requirements, as well as ambitious standards for environmental protection and sustainability, were reinvented by the Cavitec brand from the Santex Rimar Group. This company’s hotmelt technology uses one-component polymers applied to textiles in a hot, molten state. Bonding based on hotmelts is both water- and solvent-free. Drying and exhaust air cleaning are not necessary, which is an ecological advantage. Energy consumption is also significantly lower. Cavitec hotmelt technology is also developed for laminated medical protection fabrics which are safe, high-quality and sustainable. These fabrics can be washed, sterilized, and used again.   

A second skin with added value is the result of Jakob Müller Group’s cooperation with an institute for an established outdoor fashion brand. They have devised a heating mat applied as an inner jacket. Outdoor gear with a heated inlay offers the wearer a comfortable feeling even in a cold climate. The heating mat is particularly light, breathable, flexible and adjustable to three temperature levels.

Fabrics with these advantages are now possible thanks to multi direct weaving (MDW) technology from the Jakob Müller Group. A lacquer-insulated heating strand is inserted into the base textile as a ‘meander’ using MDW technology. The technology is offered with both label weaving machines and the latest generation of ribbon weaving machines. The textile pocket calculator is another MDW based future-oriented application developed in cooperation with a textile research institute.

Safety and health
Life-saving reliability is a must for vehicle airbags. They have to fulfil high security aspects, and must remain inflated for several seconds when an accident occurs. Airbags made of flat-woven fabric – cut and seamed – can show weakness at seams during the inflation phase. Latest Jacquard technology by Stäubli enables one-piece-woven (OPW) airbags to be produced, creating shape and structure in a single process. The final product is an airbag consisting of a sealed cushion with woven seams. OPW airbag weaving reduces the number of production steps, and increases the security aspects.
Another big advantage of Stäubli’s new weaving technology is the flexibility in formats required in today’s mid- and upper-range cars, where lateral protection (in the seat or in the roof over the door) has become standard and is designed in line with the car shape. Safe airbags are woven on modern high-speed weaving machines. The warp material, the variety of fabric patterns, and the importance of precisely shaped airbags require the use of a robust and reliable Jacquard machine.

A revolution for orthopaedic patients is a knitting machine from Steiger Participations, which uses compressive yarns developed to meet the needs of the specific health market. This machine model was exclusively designed for production with inlaid elastic yarns and offers optimum performance with guaranteed final product quality.

In the orthopaedic field, many Steiger flat knitting machines have already been operating as automatic, custom-made production systems. For example, the dimensions of an injured limb are taken by the doctor and fed into a web-based application. The doctor selects the compression class in the various sections of the item and a data file created by the software automatically applies a preconfigured program. With no human intervention required, the program is generated and produced on the machine, precisely matching the patient’s dimensions. Each product is different, and generally available within 48 hours.

(c) SHIMA SEIKI MFG., LTD.
14.06.2022

SHIMA SEIKI to exhibit at Techtextil 2022 in Frankfurt

SHIMA SEIKI MFG., LTD. of Wakayama, Japan, along with its Italian subsidiary SHIMA SEIKI ITALIA S.p.A., will be participating in the Techtextil exhibition in Frankfurt, Germany from the 21st till the 24th of June 2022.

SHIMA SEIKI MFG., LTD. of Wakayama, Japan, along with its Italian subsidiary SHIMA SEIKI ITALIA S.p.A., will be participating in the Techtextil exhibition in Frankfurt, Germany from the 21st till the 24th of June 2022.

On display will be SHIMA SEIKI’s latest innovation in flat knitting technology as applied to the field of technical textiles—a prototype weft knitting machine capable of multi-axial yarn insertion. Fabrics produced on this machine use inlay technique for the production of hybrid textiles that combine the stretch characteristics of knitted fabrics with the stability of woven textiles, suited to various technical applications. To this, warp yarn is inserted to further expand its capability to produce 3D-shaped carbon fiber and composite preforms directly on the machine. This is made possible by taking advantage of the fact that flat knitting as a textile production method is capable of producing end products that are shaped-to-form and with added thickness. Compared to current methods of preform production, savings in post-processing time, material, labor and associated costs are immense, realizing efficient and sustainable production. SHIMA SEIKI’s own yarn unwinding technology is also used for optimum yarn feed and tension for use with technical yarns that are otherwise difficult to knit. Industrial textile samples knit on the multi-axial machine will also be available for examination on-site.

SHIMA SEIKI's SDS®-ONE APEX4 3D design system will be available for demonstrations as well. Of particular interest should be its ultra-realistic simulation capability that realizes Virtual Sampling. When countless variations must be evaluated before arriving at a final design, virtual product samples can be used to streamline the decision-making process by minimizing the enormous amount of time, cost and material normally associated with producing actual samples for each variation. When approved, the same data can be converted to machine data for immediate knitting, significantly reducing lead times.

Process control with Qualiscan QMS (c) Mahlo. Process control with Qualiscan QMS.
17.05.2022

Mahlo at Techtextil 2022

At Techtextil from 21-24 June in Frankfurt, Mahlo will be demonstrating how manufacturers of technical textiles can optimise their production even further using measuring and control technology.

Special straightening technology for technical textiles
Mahlo's range also includes solutions for straightening distorted goods. Best suited for technical textiles are, for example, the symbol of the straightening machine, the Orthopac RVMC-15 and the reinforced version Orthopac GRVMC-15. Frame, bearings, and rollers are designed for high loads and allow large working widths of up to 5,400 mm. As the latest development from Mahlo, the experts present the Orthopac CRVMC-15 automatic straightener, which is particularly interesting for the glass & carbon fabric industry and some special applications.

At Techtextil from 21-24 June in Frankfurt, Mahlo will be demonstrating how manufacturers of technical textiles can optimise their production even further using measuring and control technology.

Special straightening technology for technical textiles
Mahlo's range also includes solutions for straightening distorted goods. Best suited for technical textiles are, for example, the symbol of the straightening machine, the Orthopac RVMC-15 and the reinforced version Orthopac GRVMC-15. Frame, bearings, and rollers are designed for high loads and allow large working widths of up to 5,400 mm. As the latest development from Mahlo, the experts present the Orthopac CRVMC-15 automatic straightener, which is particularly interesting for the glass & carbon fabric industry and some special applications.

The Mahlo team will present the wide portfolio of intelligent scanners and sensors that record product and process parameters, such as distortion, fabric temperature, dwell time, basis weight, coating weight, thickness, moisture content, residual moisture, exhaust moisture, air permeability, etc. online. Among other things, visitors can expect to see the Famacont PMC-15 weft density measurement system in live operation. The system measures the weft or course density on the running web and compares it with the target value stored in the recipe data management system. The detected deviation from the target value is used to fully automatically control the overfeed during the needling process at the stenter frame and to ensure a constant weft/course density over the full width of the product.

Source:

Mahlo GmbH + Co. KG

After Moody's, Standard & Poor's also upgrades SGL Carbon’s rating (c) SGL Carbon
SGL
11.05.2022

After Moody's, Standard & Poor's also upgrades SGL Carbon’s rating

Standard & Poor's Global Ratings (S&P) raises its long-term rating for SGL Carbon to B- and its issue rating on its financial instruments to B. The outlook for the company is rated as stable by the renowned rating agency.

S&P Global Ratings explains the upgrade of SGL's rating with the company's improved capital structure and the reduction of net debt. The rating agency expects SGL Carbon to generate positive free cash flow in the coming years, which will support the reduction in absolute debt.

For the future development of SGL Carbon, S&P assumes an improvement in profitability based in particular on the expansion of products and materials for the future-oriented core markets of mobility, energy transition and digitalization, besides the savings from the restructuring.

"We are pleased that our operational successes and the already advanced trans-formation of SGL Carbon have been honored by the two major rating agencies - Moody's and S&P - by upgrading the ratings. We also see this as a motivation for the further development of SGL Carbon," explains Thomas Dippold, Chief Financial Officer of SGL Carbon SE.

Standard & Poor's Global Ratings (S&P) raises its long-term rating for SGL Carbon to B- and its issue rating on its financial instruments to B. The outlook for the company is rated as stable by the renowned rating agency.

S&P Global Ratings explains the upgrade of SGL's rating with the company's improved capital structure and the reduction of net debt. The rating agency expects SGL Carbon to generate positive free cash flow in the coming years, which will support the reduction in absolute debt.

For the future development of SGL Carbon, S&P assumes an improvement in profitability based in particular on the expansion of products and materials for the future-oriented core markets of mobility, energy transition and digitalization, besides the savings from the restructuring.

"We are pleased that our operational successes and the already advanced trans-formation of SGL Carbon have been honored by the two major rating agencies - Moody's and S&P - by upgrading the ratings. We also see this as a motivation for the further development of SGL Carbon," explains Thomas Dippold, Chief Financial Officer of SGL Carbon SE.

More information:
SGL Carbon
Source:

 SGL Carbon

(c) SHIMA SEIKI MFG., LTD.
25.04.2022

SHIMA SEIKI to Exhibit at JEC World 2022

Leading Japanese textile solutions provider SHIMA SEIKI MFG., LTD. of Wakayama, Japan will exhibit at the upcoming JEC World 2022 exposition to be held in Paris, France next month.

On display will be the P-CAM®131 multi-ply computerized cutting machine (NC cutting machine). SHIMA SEIKI's fast, efficient and reliable P-CAM® series computerized cutting machines are known for their innovative functions and Made-in-Japan quality, and boast the largest market share in Japan. At JEC World P-CAM®131 is shown in its most compact form, featuring a cutting area of 1,300 mm x 1,700 mm, with option for expansion. Its multi-ply cutting capability allows up to 1 inch (33mm) of fabric or material to be cut. A knife sharpening system produces a sharp, strong blade every time. Strong, robust components permit quicker response times for knife movement and more accurate cutting composites and other industrial materials. The P-CAM® lineup is ideally suited to global production in a wide range of industrial applications in addition to apparel and textiles.

Leading Japanese textile solutions provider SHIMA SEIKI MFG., LTD. of Wakayama, Japan will exhibit at the upcoming JEC World 2022 exposition to be held in Paris, France next month.

On display will be the P-CAM®131 multi-ply computerized cutting machine (NC cutting machine). SHIMA SEIKI's fast, efficient and reliable P-CAM® series computerized cutting machines are known for their innovative functions and Made-in-Japan quality, and boast the largest market share in Japan. At JEC World P-CAM®131 is shown in its most compact form, featuring a cutting area of 1,300 mm x 1,700 mm, with option for expansion. Its multi-ply cutting capability allows up to 1 inch (33mm) of fabric or material to be cut. A knife sharpening system produces a sharp, strong blade every time. Strong, robust components permit quicker response times for knife movement and more accurate cutting composites and other industrial materials. The P-CAM® lineup is ideally suited to global production in a wide range of industrial applications in addition to apparel and textiles.

Also available for video display will be SHIMA SEIKI’s latest innovation in flat knitting technology as applied to the field of technical textiles—a prototype weft knitting machine capable of multi-axial yarn insertion. Fabrics produced on this machine use inlay technique for the production of hybrid textiles that combine the stretch characteristics of knitted fabrics with the stability of woven textiles, suited to various technical applications. To this, warp yarn is inserted to further expand its capability to produce 3D-shaped carbon fiber and composite preforms directly on the machine. This is made possible because flat knitting as a textile production method is capable of producing end products that are shaped-toform and with added thickness. Therefore, savings in post-processing time, cost, material and labor as compared to current methods of preform production are immense, realizing efficient and sustainable production. SHIMA SEIKI’s own yarn unwinding technology is also used for optimum yarn feed and tension for use with technical yarns that are otherwise difficult to knit. Industrial textile samples knit on the multi-axial machine will also be available for examination on-site.

Source:

SHIMA SEIKI MFG., LTD.

(c) 2022, SSM
07.04.2022

Swiss Textile Machinery members at Techtextil

High-performance yarns now offer almost unlimited possibilities for replacing traditional raw materials in a vast range of technical applications. Often tailor-made, these filament yarns go way beyond the conventional idea of ‘textiles’ – finding new uses in sectors such as automotive, aviation, maritime, medical and construction, among many others.

Technical textiles are everywhere in our daily lives today, even if we may not always realize it. Some are in more obviously textile products, from sewing threads to artificial turf. But then, take cars as an example: modern vehicles are stuffed with parts made from sophisticated yarns. It’s common for producers of automotive parts now to send template material and requirement lists to Swiss Textile Machinery members, trusting their expertise and experience. Members operate development and testing centers with latest machine installations, where their experts devise customized solutions, as well as calling on the pure innovative spirit which is part of their DNA.

High-performance yarns now offer almost unlimited possibilities for replacing traditional raw materials in a vast range of technical applications. Often tailor-made, these filament yarns go way beyond the conventional idea of ‘textiles’ – finding new uses in sectors such as automotive, aviation, maritime, medical and construction, among many others.

Technical textiles are everywhere in our daily lives today, even if we may not always realize it. Some are in more obviously textile products, from sewing threads to artificial turf. But then, take cars as an example: modern vehicles are stuffed with parts made from sophisticated yarns. It’s common for producers of automotive parts now to send template material and requirement lists to Swiss Textile Machinery members, trusting their expertise and experience. Members operate development and testing centers with latest machine installations, where their experts devise customized solutions, as well as calling on the pure innovative spirit which is part of their DNA.

At the extremes
Technology drives applications beyond our current imagining in the case of Heberlein air splicers. Developed for a wide range of uses with high-strength technical fibers, they have no problems splicing aramid fibers up to 16’100 dtex, carbon up to 30’000 dtex, Dyneema up to 5’500 dtex, and glass up to 4’800 tex. Using compressed air, the splicers produce a tear-resistant, homogeneous splice of material without interfering knots.

Retech has the technology to achieve specifications for filament yarns, drawing and stretching fibers to perfection. Top heated godet rolls – many customized – are developed for high-performance fibers. Temperatures up to 400 °C can be achieved. Combining the right settings and wide speed ranges for each specific process results in unique end-products.

Fabric producers of high-end applications must avoid any quality risk. Yarn producers are well aware of this responsibility, so they use precision package winders for technical yarns, developed by Rieter’s subsidiary SSM. Taking yarns from ring twisting bobbins, its specialist finish winders can produce coarse-count technical yarns up to 50’000 dtex, offering a new level of flexibility and winding quality.

Lifestyle essentials
At first glance, motorists might fail to notice many of the technical yarns ‘hidden’ inside their cars. These products have functions such as providing stability with hardly any weight, or absorbing tensile forces at defined elongation. This kind of controlled elongation behaviour, for example, arises from the choice of textile material and the special construction of the yarns used.

Such specifications make twisting and cabling machines essential for the automotive industry. Saurer offers machines for the production of technical yarns made from a variety of feed materials in a very wide yarn count range. They are needed for vehicle products such as tire carcasses, toothed engine belts, seat belts, airbags and lorry tarpaulins.

Technical yarns also play a surprising role in our mobile devices. Tapping, scrolling and swiping are second nature for billions, with our phones and a plethora of other lifestyle essentials. Yet, how many people would know that the touch-sensitivity we take for granted on these screens is largely made possible by twisted glass fibers. Bräcker, part of Rieter’s components business, offers a selection of vertical sinter metal rings and nylon travelers for glass fiber twisting, so that mills can achieve high levels of productivity and quality.

Future unlimited
Automotive and communication technology are already important industries for Swiss Textile Machinery members, along with well-known technical textiles markets in sectors such as medical, transport and construction. Smart-wear is already noted as a field with significant potential. Naturally, members are constantly investigating other possibilities. Swiss textile machinery is already applied in energy (batteries), and plastics.

The Swiss Textile Machinery Pavilion will be at the Techtextil exhibition in Frankfurt, Germany, taking place from 21 to 24 June 2022.

Oerlikon Barmag celebrates its 100th anniversary (c) Oerlikon Barmag
A look at the state-of-the-art assembly of a WINGS winder
30.03.2022

Oerlikon Barmag celebrates its 100th anniversary

  • Innovation begins with creativity
  • A pioneer of the manmade fiber industry

When the manmade fiber age began a century ago, a German company was responsible for the pioneering work involved. Barmag, established in 1922, was one of the world’s first companies to construct machines for the large-scale production of synthetic staple fibers. To this day, the leading manufacturer of manmade fiber spinning systems and texturing machines in Remscheid – a brand under the aegis of the Swiss Oerlikon Group since 2007 – has shaped technological progress in this sector; in future, with ever more innovations focusing on sustainability and digitalization.

  • Innovation begins with creativity
  • A pioneer of the manmade fiber industry

When the manmade fiber age began a century ago, a German company was responsible for the pioneering work involved. Barmag, established in 1922, was one of the world’s first companies to construct machines for the large-scale production of synthetic staple fibers. To this day, the leading manufacturer of manmade fiber spinning systems and texturing machines in Remscheid – a brand under the aegis of the Swiss Oerlikon Group since 2007 – has shaped technological progress in this sector; in future, with ever more innovations focusing on sustainability and digitalization.

Barmer Maschinenfabrik Aktiengesellschaft (Barmag) is founded in Barmen, located in the Bergische Land region, on March 27, 1922. The German and Dutch founders enter unchartered technological territory, one created as the result of a groundbreaking invention: in 1884, French chemist Count Hilaire Bernigaud de Chardonnet used nitrocellulose to produce the first so-called artificial silk, later known as rayon. The following decades see rapid development focusing on the search for synthetic textile fibers and their manufacturing technologies. As one of the first machine factories, Barmag battles its way through the eventful early years of the manmade fiber industry, the ‘Roaring Twenties’ and the Great Depression – and suffers the extensive destruction of its factories at the end of World War Two. Rebuilding is successful. With the unstoppable success story of purely synthetic plastic fibers such as polyamide, the company flourishes from the 1950s through to the 1970s, establishing sites in all international, for the textile industry at the time important, industrial regions and garnering prestige across the globe in the process. In the ups and downs of expansion, global competition and crises, Barmag reaches the very pinnacle of the market and becomes the preferred technological development partner for the manmade fiber industries in China, India and Turkey. The company has been a high-impact brand under the umbrella of the Oerlikon Group since 2007.

On the wings of innovation
Today, Oerlikon Barmag is a leading supplier of manmade fiber filament spinning systems and part of the Manmade Fibers Solutions business unit of the Oerlikon Polymer Processing Solutions Division. And our aspirations have not diminished: “The striving towards innovation and technological leadership has been, is and will always be part of our DNA”, emphasizes Georg Stausberg, CEO of Oerlikon Polymer Processing Solutions. In the past, this has been observable in such trailblazing innovations as the revolutionary WINGS generation of winders for POY in 2007 and WINGS for FDY in 2012. Currently, the focus of new and further developments is very much on digitalization and sustainability. Here, Oerlikon Barmag has – as one of the world’s first systems manufacturers – been implementing fully-networked smart factories for globally-leading polyester manufacturers since the end of the last decade. Within this context, digital solutions and automation are also helping to provide greater climate and environmental compatibility. This sustainability commitment is not only evidenced by the e-save label introduced for all products back in 2004: Oerlikon is endeavoring to also make all its sites carbon-neutral by 2030 and to acquire its energy exclusively from renewable sources. An ambitious target, whose achievement could be helped by the Oerlikon Barmag anniversary, states Georg Stausberg: “Innovation begins with creativity. And remembering the past provides plenty of motivation and inspiration for the future.”

ANDRITZ at JEC World 2022 (c) ANDRITZ AG
16.03.2022

ANDRITZ at JEC World 2022

International technology group ANDRITZ will be presenting its special-purpose machines for needlepunch production (including its portfolio for carbon applications) at JEC World 2022 in Paris, France, from May 3 to 5.

Experience and Know-How
ANDRITZ designs, develops, and engineers special-purpose machines for very specific and sensitive applications, like aerospace, railway, and military needs. Therefore, it can provide the market with customized machines offering perfect solutions, whether they are needed for prototypes or for industrial production.

Skilled Engineers
In increasingly demanding markets, the skilled ANDRITZ engineers and technicians help customers get the most out of their investments. The variety of cases they face every day enables them to optimize both output and quality depending on the fibers used, the challenge, and the customer’s final application.

International technology group ANDRITZ will be presenting its special-purpose machines for needlepunch production (including its portfolio for carbon applications) at JEC World 2022 in Paris, France, from May 3 to 5.

Experience and Know-How
ANDRITZ designs, develops, and engineers special-purpose machines for very specific and sensitive applications, like aerospace, railway, and military needs. Therefore, it can provide the market with customized machines offering perfect solutions, whether they are needed for prototypes or for industrial production.

Skilled Engineers
In increasingly demanding markets, the skilled ANDRITZ engineers and technicians help customers get the most out of their investments. The variety of cases they face every day enables them to optimize both output and quality depending on the fibers used, the challenge, and the customer’s final application.

Carbon Expertise
Experience with conductive fibers enables ANDRITZ to overcome challenges and provide access to new product developments. The company’s expertise lies in textile know-how as well as a deep understanding of related constraints. It includes carded/crosslapped processes for nonwovens made from recycled carbon fibers, which can be delivered in rolls or die-cut shapes.

Unconventional Needling for End-Uses
ANDRITZ addresses customers’ challenges by offering solutions and expertise in terms of straight and multi-axial needling, enabling the consolidation of fibers on flat or non-flat surfaces (such as rounded shapes) and even of layers up to 350 mm thick. New developments are made possible thanks to the outstanding ANDRITZ testing facility.

Support and Development
The ANDRITZ needlepunch technical center in Elbeuf, France, is open to visitors. Innovative strength and adaptability are the characteristics that make ANDRITZ the preferred partner in the search for genuine, efficient, and reliable solutions in the interests of productivity and premium, state-of-the-art consolidation. Secrecy being key in such sensitive development work, ANDRITZ naturally always guarantees the utmost confidentiality.

More information:
Andritz JEC World needlepunch
Source:

ANDRITZ AG

The Green Revolution: How Microfactories Can Change the Face of Fashion by Mark Sollman, Product Manager EMEA, Mimaki Europe (c) Mimaki EMEA
Traditionally, apparel manufacturing has centred on a production chain model of sourcing materials and producing garments in bulk, microfactories are now enabling on-demand, on-location production
12.01.2022

Mimaki Europe: The Green Revolution

  • The Green Revolution: How Microfactories Can Change the Face of Fashion by Mark Sollman, Product Manager EMEA, Mimaki Europe

With the all-important COP26 Climate Change Conference having taken centre stage in November, there is no time like the present for the fashion world to rally together in stepping up sustainability efforts and getting carbon emissions under control. Globally, the fashion industry is now estimated to account for around 10 percent of greenhouse gas emissions and 20 percent of wastewater , making the pursuit of greener production methods more pertinent than ever before. Thankfully, we are seeing a new era of production enter the fashion arena, with the increasing emergence of technologically advanced, highly automated microfactories.

Along with reducing unnecessary waste through on-demand production, microfactories have a smaller ecological footprint than traditional garment production and require no water use during the production process, making it not only a faster solution, but a greener one too.

  • The Green Revolution: How Microfactories Can Change the Face of Fashion by Mark Sollman, Product Manager EMEA, Mimaki Europe

With the all-important COP26 Climate Change Conference having taken centre stage in November, there is no time like the present for the fashion world to rally together in stepping up sustainability efforts and getting carbon emissions under control. Globally, the fashion industry is now estimated to account for around 10 percent of greenhouse gas emissions and 20 percent of wastewater , making the pursuit of greener production methods more pertinent than ever before. Thankfully, we are seeing a new era of production enter the fashion arena, with the increasing emergence of technologically advanced, highly automated microfactories.

Along with reducing unnecessary waste through on-demand production, microfactories have a smaller ecological footprint than traditional garment production and require no water use during the production process, making it not only a faster solution, but a greener one too.

Last year’s FESPA saw Mimaki team up with fashion designer Carolina Guzman to bring her designs to life in real time at the show, setting up its own working microfactory live on-site to take her designs from screen to garment within just a day. Guzman’s designs were created using Mimaki’s TS100-1600 Sublimation Printer, before being transferred to textile, digitally cut and finally pieced together. Devised with a string of ethical and environmental objectives threaded throughout, the microfactory also exclusively utilised eco-friendly Greentex fabric, and any remaining material was donated to Sheltersuit: a wind- and waterproof coat that can be transformed into a sleeping bag, which is provided free of charge to homeless people and refugees.

Through working with a number of strategic partners – including transfer printing expert, Klieverik; paper solutions specialist, Neenah Coldenhove; and digital cutting equipment provider, Summa – Mimaki was able to produce a collection of unique, high-quality garments live on the stand during the tradeshow, demonstrating to visitors from more than 100 countries some of the key reasons that microfactories seem set to change the future of fashion…

Unparalleled speed and versatility
Where traditionally, apparel manufacturing has centred on a production chain model of sourcing materials and producing garments in bulk, microfactories are now enabling on-demand, on-location production, making it possible to create everything from unique, one-off pieces and samples right through to entire product lines – all at unprecedented speeds. This means greater flexibility and customisation, enabling designers to modify or update designs and respond to market trends as they occur.

Simplified supply chains and minimised risk
The microfactory setup brings production in-house and on-demand, minimising the cost of not only storing stock, but also of shipping it and responsibly disposing of unsold items. Where recent geopolitical events have highlighted the fragility of global supply chains, microfactories offer a unique independence from these systems, empowering garment manufacturers to future-proof their businesses, become less reliant on external systems and suppliers, and reduce the risk of disruptions.

A boosted bottom line and a greener future
Facilitating savings in a whole line of resources, from physical storage and production space to time and energy, microfactories ultimately have the potential to significantly increase profitability for garment manufacturers, with the additional benefit of being easily scalable as production increases. Perhaps even more compelling, however, are the environmental considerations. Demonstrated on a small scale through Mimaki’s recent project, the environmental benefits inherent to microfactory production will have an even greater impact as it becomes more prolific and commonplace throughout the fashion world, with the potential to effect meaningful environmental change as adoption increases in the years to come.