From the Sector

Reset
10 results
Ascend Performance Materials, APMPR063 ©Ascend Performance Materials
SARS-CoV-2, Influenza A inactivated by zinc-embedded nylon fabric.
22.09.2021

SARS-CoV-2, Influenza A inactivated by zinc-embedded nylon fabric

  • A paper published in ACS Applied Materials Interfaces details effectiveness, describes protocol for future testing

An international team of scientists and engineers from the University of Cambridge, the Icahn School of Medicine at Mount Sinai, ResInnova Labs and Ascend Performance Materials has found that a nylon fabric embedded with zinc ions successfully inactivated 99% of the viruses that cause COVID-19 and the common flu.

Face masks, protective clothing and filters are used to slow the spread of viruses. But poor-quality masks can harbor active viruses from infected wearers, posing a transmission risk.

“A major challenge is absorption and inactivation,” said Vikram Gopal, Ph.D., co-senior author and chief technology officer at Ascend Performance Materials. “Respiratory viral illnesses, such as COVID-19, and the flu, are transmitted through droplets and aerosols. Polypropylene, the material in commonly used disposable masks, is a hydrophobic plastic and does not absorb moisture. Instead, the viruses can sit on the surface of the mask, posing a transmission risk when the mask is handled.”

  • A paper published in ACS Applied Materials Interfaces details effectiveness, describes protocol for future testing

An international team of scientists and engineers from the University of Cambridge, the Icahn School of Medicine at Mount Sinai, ResInnova Labs and Ascend Performance Materials has found that a nylon fabric embedded with zinc ions successfully inactivated 99% of the viruses that cause COVID-19 and the common flu.

Face masks, protective clothing and filters are used to slow the spread of viruses. But poor-quality masks can harbor active viruses from infected wearers, posing a transmission risk.

“A major challenge is absorption and inactivation,” said Vikram Gopal, Ph.D., co-senior author and chief technology officer at Ascend Performance Materials. “Respiratory viral illnesses, such as COVID-19, and the flu, are transmitted through droplets and aerosols. Polypropylene, the material in commonly used disposable masks, is a hydrophobic plastic and does not absorb moisture. Instead, the viruses can sit on the surface of the mask, posing a transmission risk when the mask is handled.”

Cotton also has problems, Dr. Gopal said. “Cotton effectively absorbs moisture, but it doesn’t inactivate the virus – again, posing a transmission risk,” he said. In the paper published in ACS Applied Materials Interfaces, the researchers described how a fabric made of nylon 6,6 embedded with active zinc ions absorbed virus-containing moisture droplets and effectively inactivated the particles. The fabric produced a 2-log, or 99%, reduction of virus particles in one hour.

The research team also was able to demonstrate that nylon with active zinc ions remains stable over time, keeping its virus-inactivating properties after 50 washes. “The study shows how nylon textile fabric with zinc outperforms the widely used cotton and polypropylene materials at virus absorption and inactivation,” Dr. Gopal said. The findings have significant implications for future development of PPE, Dr. Gopal said. “Pathogen-free PPE does more than just cut down the risk of transmitting the virus,” Gopal said. “By making PPE washable and reusable, you reduce the need for single-use products, keeping hundreds of millions of masks out of landfills.”

(c) FET
FET meltspinning system for biomedical applications
15.09.2021

FET: Further Gains in the Biomedical sector

Fibre Extrusion Technology of Leeds, UK has delivered nine meltspinning systems to clients in the biomedical sector since the onset of the Covid-19 pandemic, with a similar number currently on order for 2021/22. This way FET could confirm the position as an acknowledged world leader in meltspinning equipment for the production of precursor materials used in medical devices and as a default supplier for absorbable suture production systems, with orders virtually doubling year on year.

Recent installations include a multi-functional system that can produce both multifilament and monofilament pre-cursor fibres, but nonwoven systems have been particularly prominent, driven by the burgeoning demand for FFP3 masks, gowns and other medical products required during the pandemic. These have been sold to medical device manufacturing companies across the globe, including the Far East, USA and Europe. Research organisations have also invested in FET systems for biomedical applications, the most recent being the University of Leeds in a laboratory scale Spunbond system.

Fibre Extrusion Technology of Leeds, UK has delivered nine meltspinning systems to clients in the biomedical sector since the onset of the Covid-19 pandemic, with a similar number currently on order for 2021/22. This way FET could confirm the position as an acknowledged world leader in meltspinning equipment for the production of precursor materials used in medical devices and as a default supplier for absorbable suture production systems, with orders virtually doubling year on year.

Recent installations include a multi-functional system that can produce both multifilament and monofilament pre-cursor fibres, but nonwoven systems have been particularly prominent, driven by the burgeoning demand for FFP3 masks, gowns and other medical products required during the pandemic. These have been sold to medical device manufacturing companies across the globe, including the Far East, USA and Europe. Research organisations have also invested in FET systems for biomedical applications, the most recent being the University of Leeds in a laboratory scale Spunbond system.

The FET in-house Process Development Laboratory and ongoing collaboration with biomaterial polymer suppliers has helped to optimise the biomedical melt spinning technology. The Laboratory is at the disposal of customers for all aspects of confidential testing and evaluation. To further increase this competitive edge, FET will be opening a new Process Development Laboratory and Visitor Centre in early 2022.

More information:
meltspinning FET
Source:

Projectmarketing for FET

16.06.2021

Closed-loop recycling pilot project for single-use facemasks

  • Fraunhofer, SABIC, and Procter & Gamble join forces
  • The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics.
  • The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

Due to COVID-19, use of billions of disposable facemasks is raising environmental concerns especially when they are thoughtlessly discarded in public spaces, including - parks, open-air venues and beaches. Apart from the challenge of dealing with such huge volumes of essential personal healthcare items in a sustainable way, simply throwing the used masks away for disposal on landfill sites or in incineration plants represents a loss of valuable feedstock for new material.

  • Fraunhofer, SABIC, and Procter & Gamble join forces
  • The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics.
  • The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

Due to COVID-19, use of billions of disposable facemasks is raising environmental concerns especially when they are thoughtlessly discarded in public spaces, including - parks, open-air venues and beaches. Apart from the challenge of dealing with such huge volumes of essential personal healthcare items in a sustainable way, simply throwing the used masks away for disposal on landfill sites or in incineration plants represents a loss of valuable feedstock for new material.

“Recognizing the challenge, we set out to explore how used facemasks could potentially be returned into the value chain of new facemask production”, says Dr. Peter Dziezok, Director R&D Open Innovation at P&G. “But creating a true circular solution from both a sustainable and an economically feasible perspective takes partners. Therefore, we teamed up with Fraunhofer CCPE and Fraunhofer UMSICHT’s expert scientists and SABIC’s Technology & Innovation specialists to investigate potential solutions.”

As part of the pilot, P&G collected used facemasks worn by employees or given to visitors at its manufacturing and research sites in Germany. Although those masks are always disposed of responsibly, there was no ideal route in place to recycle them efficiently. To help demonstrate a potential step change in this scenario, special collection bins were set up, and the collected used masks were sent to Fraunhofer for further processing in a dedicated research pyrolysis plant.

“A single-use medical product such as a face mask has high hygiene requirements, both in terms of disposal and production. Mechanical recycling, would have not done the job”, explains Dr. Alexander Hofmann, Head of Department Recycling Management at Fraunhofer UMSICHT. “In our solution, therefore, the masks were first automatically shredded and then thermochemically converted to pyrolysis oil. Pyrolysis breaks the plastic down into molecular fragments under pressure and heat, which will also destroy any residual pollutants or pathogens, such as the Coronavirus. In this way it is possible to produce feedstock for new plastics in virgin quality that can also meet the requirements for medical products”, adds Hofmann, who is also Head of Research Department “Advanced Recycling” at Fraunhofer CCPE.

The pyrolysis oil was then sent to SABIC to be used as feedstock for the production of new PP resin. The resins were produced using the widely recognized principle of mass balance to combine the alternative feedstock with fossil-based feedstock in the production process. Mass balance is considered a crucial bridge between today’s large scale linear economy and the more sustainable circular economy of the future, which today is operated on a smaller scale but is expected to grow quickly.

“The high-quality circular PP polymer obtained in this pilot clearly demonstrates that closed-loop recycling is achievable through active collaboration of players from across the value chain”, emphasizes Mark Vester, Global Circular Economy Leader at SABIC. “The circular material is part of our TRUCIRCLE™ portfolio, aimed at preventing valuable used plastic from becoming waste and at mitigating the depletion of fossil resources.”

Finally, to close the loop, the PP polymer was supplied to P&G, where it was processed into non-woven fibers material. “This pilot project has helped us to assess if the close loop approach could work for hygienic and medical grade plastics”, says Hansjörg Reick, P&G Senior Director Open Innovation. “Of course, further work is needed but the results so far have been very encouraging.”

The entire closed loop pilot project from facemask collection to production was developed and implemented within seven months. The transferability of advanced recycling to other feedstocks and chemical products is being further researched at Fraunhofer CCPE.

Source:

Fraunhofer

Bunzl Distribution brings American antiviral technology to Mexico retailers
19.04.2021

Bunzl Distribution brings American antiviral technology to Mexico retailers

US-made Acteev Protect™ masks have embedded zinc ion technology which deactivates many viruses and eliminates bacteria

Bunzl Distribution, a leading supplier of packaging, disposable supplies, and cleaning and safety products, has signed on as the distributor in Mexico for Acteev Protect™ masks, made in the United States by polyamide manufacturer Ascend Performance Materials. A global distributor, Bunzl provides supplies to supermarkets, food processing plants, retailers and convenience stores in Mexico.

Bunzl will distribute the Acteev Protect Nonwoven Mask, a reusable general purpose mask that features powerful antiviral and antibacterial properties. Acteev technology embeds active zinc ions in a polymer matrix which destroys microbes, deactivates many viruses and eliminates bacteria and fungi.

US-made Acteev Protect™ masks have embedded zinc ion technology which deactivates many viruses and eliminates bacteria

Bunzl Distribution, a leading supplier of packaging, disposable supplies, and cleaning and safety products, has signed on as the distributor in Mexico for Acteev Protect™ masks, made in the United States by polyamide manufacturer Ascend Performance Materials. A global distributor, Bunzl provides supplies to supermarkets, food processing plants, retailers and convenience stores in Mexico.

Bunzl will distribute the Acteev Protect Nonwoven Mask, a reusable general purpose mask that features powerful antiviral and antibacterial properties. Acteev technology embeds active zinc ions in a polymer matrix which destroys microbes, deactivates many viruses and eliminates bacteria and fungi.

Recent testing on Acteev fabric completed at the University of Cambridge has demonstrated that Acteev technology deactivates the virus that causes COVID-19, SARS-CoV-2, with greater than 99.9% efficacy. Ascend has submitted several masks designs to the U.S. Environmental Protection Agency and the U.S. Food and Drug Administration to obtain the appropriate regulatory clearances to make specific claims regarding the technology’s antiviral properties in the United States.

Carlos Green, Director General of Bunzl de México, says the company is pleased to bring products featuring better safety and protection to the Mexico market. “Our customers are more focused than ever before on doing business safely, and Acteev masks offer an added level of protection in the workplace,” he said. “We’re excited to offer our customers this premium product that provides some of the best protection available.”

In addition to antiviral, antifungal and antibacterial protection, the washable, reusable masks are lightweight, breathable and odor-fighting, making them comfortable to wear during a long shift at work or for outdoor workout. “Workers in industrial settings, such as chemical and food processing plants, and convenience stores and other retail outlets deserve the right protection as they keep society and the economy moving in Mexico,” said Juan Toro, Ascend’s principal business development leader for Acteev in the Americas.

“We are proud to partner with Bunzl to help deliver a reusable mask that provides both antiviral properties as well as an opportunity reduce the number of masks consumed, saving the companies money.”
Acteev Protect shows promise for use beyond masks, according to Ascend. The technology was originally developed for workout wear, and now the company is working textile applications ranging from gloves to scrubs to high-end athleisure.

Antiviral and antibacterial zwissCLEAN masks® of zwissTEX (c) zwissTex
zwissCLEAN MASK BASIC
21.10.2020

Antiviral and antibacterial zwissCLEAN masks® of zwissTEX

With zwissCLEAN® masks, zwissTEX is a pioneer among manufacturers of antiviral and antibacterial oronasal masks. Unlike conventional models they actively and highly effectively eliminate viruses and bacteria thanks to the latest textile technologies. This is made possible by an environmentally friendly finishing that foregoes the use of silver and zinc. "The formula physically interrupts the cell membrane of the viruses and bacteria - so no development of resistance is possible. In this way 99.9 percent of viruses and bacteria are eliminated within a very short time," says Maximilian Schönfließ - Business Development Manager of zwissTEX.

The zwissCLEAN MASK BASIC is particularly suitable when a mask is to be worn over a longer period of time - whether for school, concerts, trade fair visits or air travel. "The special feature of our zwissCLEAN MASK BASIC is that it can be worn for up to 12 hours without any problems due to the breathable material", says Schönfließ. "With it even sleeping is possible. And unlike disposable masks it can be washed up to 10 times at 30 degrees. Disposal by type is also possible".

With zwissCLEAN® masks, zwissTEX is a pioneer among manufacturers of antiviral and antibacterial oronasal masks. Unlike conventional models they actively and highly effectively eliminate viruses and bacteria thanks to the latest textile technologies. This is made possible by an environmentally friendly finishing that foregoes the use of silver and zinc. "The formula physically interrupts the cell membrane of the viruses and bacteria - so no development of resistance is possible. In this way 99.9 percent of viruses and bacteria are eliminated within a very short time," says Maximilian Schönfließ - Business Development Manager of zwissTEX.

The zwissCLEAN MASK BASIC is particularly suitable when a mask is to be worn over a longer period of time - whether for school, concerts, trade fair visits or air travel. "The special feature of our zwissCLEAN MASK BASIC is that it can be worn for up to 12 hours without any problems due to the breathable material", says Schönfließ. "With it even sleeping is possible. And unlike disposable masks it can be washed up to 10 times at 30 degrees. Disposal by type is also possible".

The zwissCLEAN MASK COMFORT is recommended for daily protection at shopping, on public transport, at business appointments or similar events. It consists of a three-layer structure and combines efficient antiviral protection with long-term wearing comfort. The outer material and the integrated fleece promote protection against viruses and bacteria. The lower material made of organic cotton guarantees a lasting pleasant feeling on the skin. The mask can be washed up to 30 times, thus replacing up to 210 disposable masks and saving resources sustainably.

Source:

zwissTex

With the PFAFF 4520, engineers and technicians from PFAFF have designed a full-automatic production line (CE compliant) for processing multi-layer disposable masks, which meets the requirements of "German engineering" in a unique way. (c) PFAFF
PFAFF 4520: Full-automatic mask production unit
05.10.2020

PFAFF 4520: Full-automatic mask production unit

With the PFAFF 4520, engineers and technicians from PFAFF have designed a full-automatic production line (CE compliant) for processing multi-layer disposable masks, which meets the requirements of "German engineering" in a unique way. The product combines 150 years of expertise in joining textile materials and a concentrated know-how of the PFAFF INDUSTRIAL and KSL brands in the areas of process control, automation and robotics.

The PFAFF 4520 is an investment in a robust and sophisticated production line (MADE IN GERMANY) with an exceptionally reliable working process. In times of Covid-19 it is so important to rely on the right equipment for the mask production and avoid costly readjustments or an unnecessary second investment!

Key facts of the unit:

With the PFAFF 4520, engineers and technicians from PFAFF have designed a full-automatic production line (CE compliant) for processing multi-layer disposable masks, which meets the requirements of "German engineering" in a unique way. The product combines 150 years of expertise in joining textile materials and a concentrated know-how of the PFAFF INDUSTRIAL and KSL brands in the areas of process control, automation and robotics.

The PFAFF 4520 is an investment in a robust and sophisticated production line (MADE IN GERMANY) with an exceptionally reliable working process. In times of Covid-19 it is so important to rely on the right equipment for the mask production and avoid costly readjustments or an unnecessary second investment!

Key facts of the unit:

-    Size of the mask: 175 x 95 mm
-    Output:  3,500 – 4,000 masks per hour
-    1-, 2- or 3 ply processing  (Non-woven/filtration fabric)
-    SPS (PLC) control of the entire mask system
-    Exceedingly quiet working process of the whole unit
-    Ultrasonic welding components from German manufacturers
-    Protective housing for occupational safety of the operator
-    Packing station + printing station for personalized masks (on request)

The machine package also includes important features in the pre- and after sales:

PFAFF technicians ensure the adjustment of the desired customer material (non-woven or similar filter material) and the number of layers (1-, 2-, 3-ply) to the machine and make a "Ready to production" installation of the whole unit at the customer.  A fast service response time in after-sales (by involvement of the PFAFF sales- and service partner on site) ensures a maximum production output.

Coating expertise brings sustainable comfort and convenience to the face mask (c) A. Monforts Textilmaschinen GmbH & Co. KG
The masks are based on 100% woven cotton and the active ingredients in the finish are a reaction mass of titanium dioxide and silver chloride
21.09.2020

Coating expertise brings sustainable comfort and convenience to the face mask

  • Gorilla Protect is a new company formed in May this year to promote the Catus face mask – a major leap forward in the effectiveness of personal protection products that are available to consumers in the fight against Covid-19.
  • Behind Catus and the new company is Nova Textil, the established fabric finishing company based in Grefrath, Germany, and now run by father and son team Rainer and Oliver Hurtz.

Single stenter

Rainer Hurtz founded Nova Textil with a single Monforts Montex stenter and just five employees in 1999 and has steered its constant development and growth over the past twenty years.

“Our initial focus was on the coating of mainly glass fibre fabrics, awnings and sun protection products for outdoor furnishings,” he said. “We had a great customer who was providing us with so many orders that by 2005 we took the decision to order a second Montex stenter, in a special configuration. This also allowed us to enter the market for blackout and digital printing fabrics. We’ve had a great ongoing relationship with Monforts from the beginning.”

  • Gorilla Protect is a new company formed in May this year to promote the Catus face mask – a major leap forward in the effectiveness of personal protection products that are available to consumers in the fight against Covid-19.
  • Behind Catus and the new company is Nova Textil, the established fabric finishing company based in Grefrath, Germany, and now run by father and son team Rainer and Oliver Hurtz.

Single stenter

Rainer Hurtz founded Nova Textil with a single Monforts Montex stenter and just five employees in 1999 and has steered its constant development and growth over the past twenty years.

“Our initial focus was on the coating of mainly glass fibre fabrics, awnings and sun protection products for outdoor furnishings,” he said. “We had a great customer who was providing us with so many orders that by 2005 we took the decision to order a second Montex stenter, in a special configuration. This also allowed us to enter the market for blackout and digital printing fabrics. We’ve had a great ongoing relationship with Monforts from the beginning.”

A third Montex stenter line was installed at the company’s Grefrath plant in 2015, by which time the company had grown to 40 people and a major new market had opened up in the supply of fabrics for promotional materials at exhibitions and trade shows.

“We had a fantastic two years in 2018 and 2019 and everything was going great for the first three months of this year, but in April it all came crashing down,” said Oliver Hurtz. “Coronavirus put an end to trade shows in 2020, which had a very serious impact on our business.”

At the same time, however, the company was exploring the potential of a new biocidal product from one of its chemicals suppliers which has both antiviral and antimicrobial properties.

Filtration

“We had already been producing coated fabrics for hot gas filtration and realised that in combination with this new microporous coating we had the basis for a very effective single-layer face mask,” Rainer said. “Achieving this with a single layer product rather than the usual three has resulted in a significant advance in comfort for the wearer and because the mask is able to disinfect itself and helps regulate humidity, it can be worn a number of times without needing to be washed, for greater convenience. It only needs to be washed when it gets dirty and can also be washed up to twenty times without losing its properties, which has to be preferable to single-use disposables.”

Catus face masks are based on 100% woven cotton and the active ingredients in the finish are a reaction mass of titanium dioxide and silver chloride certified to ISO 20743 for their antibacterial effect, and to ISO 18184 for their antiviral effect.

They are proven to  eliminate over  99.99% of the human coronavirus 229 E, with the multiplication of microorganisms such as germs and bacteria prevented by the biostatic action of silver salts and viruses destroyed by oxygen-releasing substances and a mechanism that attacks their fatty envelope. The virus membrane loses its cholesterol content and the virus is inactivated.

Colours

Gorilla Protect next plans to make the masks available in four colours – black, Bordeaux, olive and grey – and is also working on colour branding and printing labels.

“It’s not possible to print on the surface of the mask after it has been coated, but its is possible for volume orders to be printed before the treatment,” Oliver Hurtz said.

“Face masks are going to become an established part of life in the West like they are in Asia and need to be as comfortable and convenient as possible for the wearer,” his father concluded. “With these things in mind, we believe Catus is a significant step forward.”

zwissTEX adds zwissCLEAN MASK BASIC to the zwissCLEAN® antiviral and antibacterial range (c) zwissTEX GmbH
zwissCLEAN MASK BASIC
10.09.2020

zwissCLEAN® range is being expanded

  • zwissTEX adds zwissCLEAN MASK BASIC to the zwissCLEAN® antiviral and antibacterial range

zwissTEX is adding a BASIC mask to the zwissCLEAN® range which is particularly suitable when a mask is to be worn over a longer period of time - whether for school, concerts, trade fair visits or air travel. "The special feature of our zwissCLEAN MASK BASIC is that it can be worn for up to 12 hours without any problems due to the breathable material", says Maximilian Schönfließ - Business Development Manager of zwissTEX. "With it even sleeping is possible. And unlike disposable masks it can be washed up to 10 times at 30 degrees. Disposal by type is also possible".

  • zwissTEX adds zwissCLEAN MASK BASIC to the zwissCLEAN® antiviral and antibacterial range

zwissTEX is adding a BASIC mask to the zwissCLEAN® range which is particularly suitable when a mask is to be worn over a longer period of time - whether for school, concerts, trade fair visits or air travel. "The special feature of our zwissCLEAN MASK BASIC is that it can be worn for up to 12 hours without any problems due to the breathable material", says Maximilian Schönfließ - Business Development Manager of zwissTEX. "With it even sleeping is possible. And unlike disposable masks it can be washed up to 10 times at 30 degrees. Disposal by type is also possible".

With zwissCLEAN® masks, zwissTEX is a pioneer among manufacturers of antiviral and antibacterial oronasal masks. Unlike conventional models they actively and highly effectively eliminate viruses and bacteria thanks to the latest textile technologies. This is made possible by an environmentally friendly finishing that foregoes the use of silver and zinc. "The formula physically interrupts the cell membrane of the viruses and bacteria - so no development of resistance is possible. In this way 99.9 percent of viruses and bacteria are eliminated within a very short time," says Schönfließ.

The zwissCLEAN MASK COMFORT is recommended for daily protection at shopping, on public transport, at business appointments or similar events. It consists of a three-layer structure and combines efficient antiviral protection with long-term wearing comfort. The outer material and the integrated fleece promote protection against viruses and bacteria. The lower material made of organic cotton guarantees a lasting pleasant feeling on the skin. The mask can be washed up to 30 times, thus replacing up to 210 disposable masks and saving resources sustainably.

The zwissCLEAN® range is being continuously expanded. "In addition to mask production we plan to manufacture antiviral and antibacterial gloves," says Schönfließ. "The test phase is already underway and we will start production of the gloves in the coming weeks.

More information:
zwissTex GmbH Mund-Nase-Maske
Source:

zwissTEX GmbH

Devan (c) Devan
25.03.2020

Devan offers antiviral solutions for textiles' professional workers

Textile innovator and specialty chemical producer Devan answers questions regarding anti-viral textile finish solutions following the growing spread of the COVID-19 outbreak.

Over the past few weeks, Devan has received a lot of questions regarding an antiviral solution for textiles against Sars-COV-2, the virus that causes COVID-19. “Not a big surprise since we put BI-OME AV forward 3 years ago. Testing has been done in cooperation with Institut Pasteur de Lille”, says Devan CEO Sven Ghyselinck. Devan studied enveloped viruses (e.g. H1N1, Corona-types, etc.) as well as naked viruses (e.g. Rotavirus). For both virus families, BI-OME AV showed strong to excellent activity in wet state.

Textile innovator and specialty chemical producer Devan answers questions regarding anti-viral textile finish solutions following the growing spread of the COVID-19 outbreak.

Over the past few weeks, Devan has received a lot of questions regarding an antiviral solution for textiles against Sars-COV-2, the virus that causes COVID-19. “Not a big surprise since we put BI-OME AV forward 3 years ago. Testing has been done in cooperation with Institut Pasteur de Lille”, says Devan CEO Sven Ghyselinck. Devan studied enveloped viruses (e.g. H1N1, Corona-types, etc.) as well as naked viruses (e.g. Rotavirus). For both virus families, BI-OME AV showed strong to excellent activity in wet state.

In the first instance, the company wants to focus on professionals who need to stay working such as policemen, logistics workers, shop employees, day-care workers, … A common complication of respiratory viral disease can be a secondary bacterial infection. Professionals could be helped with either an anti-bacterial on their facemask to reduce the chance for these secondary bacterial infections, for better hygiene and less odor build-up. On workwear, a combination of a virus spread reducing and antibacterial solution could help as these garments are typically used during long hours, are non-disposable and most likely will be washed at home.

Devan has solutions which withstand washing while keeping its performance. BI-OME as a liquid product is EU BPR, Turkish BPR and US EPA registered. Depending on the rash region, commercialising treated articles be subject to additional local registration procedures.

More information:
Devan Coronavirus
Source:

Devan

25.03.2020

DEVAN: Antiviral solutions for textiles

Textile innovator and specialty chemical producer Devan answers questions regarding anti-viral textile finish solutions following the growing spread of the COVID-19 outbreak.

Devan studied enveloped viruses (e.g. H1N1, Corona-types etc.) as well as naked viruses (e.g. Rotavirus). For both virus families BI-OME AV showed strong activity in wet state.
In the first instance, the company wants to focus on professionals who need to stay working such as policemen, logistics workers, shop employees, day-care workers.

A common complication of respiratory viral disease can be a secondary bacterial infection. Professionals could be helped with either an anti-bacterial on their facemask to reduce the chance for these secondary bacterial infections, for better hygiene and less odour build-up. On workwear, a combination of a virus spread reducing and antibacterial solution could help as these garments are typically used during long hours, are non-disposable and most likely will be washed at home.
 

Textile innovator and specialty chemical producer Devan answers questions regarding anti-viral textile finish solutions following the growing spread of the COVID-19 outbreak.

Devan studied enveloped viruses (e.g. H1N1, Corona-types etc.) as well as naked viruses (e.g. Rotavirus). For both virus families BI-OME AV showed strong activity in wet state.
In the first instance, the company wants to focus on professionals who need to stay working such as policemen, logistics workers, shop employees, day-care workers.

A common complication of respiratory viral disease can be a secondary bacterial infection. Professionals could be helped with either an anti-bacterial on their facemask to reduce the chance for these secondary bacterial infections, for better hygiene and less odour build-up. On workwear, a combination of a virus spread reducing and antibacterial solution could help as these garments are typically used during long hours, are non-disposable and most likely will be washed at home.
 

More information:
Devan face masks antiviral
Source:

Marketing Solutions NV