From the Sector

Reset
38 results
Figure 1: Adsorption of a drop of waste oil within seconds by a leaf of the floating fern Salvinia molesta. Abbildung 1 © W. Barthlott, M. Mail/Universität Bonn
Figure 1: Adsorption of a drop of waste oil within seconds by a leaf of the floating fern Salvinia molesta.
14.12.2023

Self-driven and sustainable removal of oil spills in water using textiles

Researchers at the ITA, the University of Bonn and Heimbach GmbH have developed a new method for removing oil spills from water surfaces in an energy-saving, cost-effective way and without the use of toxic substances. The method is made possible by a technical textile that is integrated into a floating container. A single small device can remove up to 4 liters of diesel within an hour. This corresponds to about 100 m2 of oil film on a water surface.
 
Despite the steady expansion of renewable energies, global oil production, oil consumption and the risk of oil pollution have increased steadily over the last two decades. In 2022, global oil production amounted to 4.4 billion tons! Accidents often occur during the extraction, transportation and use of oil, resulting in serious and sometimes irreversible environmental pollution and harm to humans.

There are various methods for removing this oil pollution from water surfaces. However, all methods have various shortcomings that make them difficult to use and, in particular, limit the removal of oil from inland waters.

Researchers at the ITA, the University of Bonn and Heimbach GmbH have developed a new method for removing oil spills from water surfaces in an energy-saving, cost-effective way and without the use of toxic substances. The method is made possible by a technical textile that is integrated into a floating container. A single small device can remove up to 4 liters of diesel within an hour. This corresponds to about 100 m2 of oil film on a water surface.
 
Despite the steady expansion of renewable energies, global oil production, oil consumption and the risk of oil pollution have increased steadily over the last two decades. In 2022, global oil production amounted to 4.4 billion tons! Accidents often occur during the extraction, transportation and use of oil, resulting in serious and sometimes irreversible environmental pollution and harm to humans.

There are various methods for removing this oil pollution from water surfaces. However, all methods have various shortcomings that make them difficult to use and, in particular, limit the removal of oil from inland waters.

For many technical applications, unexpected solutions come from the field of biology. Millions of years of evolution led to optimized surfaces of living organisms for their interaction with the environment. Solutions - often rather unfamiliar to materials scientists and difficult to accept. The long-time routine examination of around 20,000 different species showed that there is an almost infinite variety of structures and functionalities. Some species in particular stand out for their excellent oil adsorption properties. It was shown that, e.g., leaves of the floating fern Salvinia molesta, adsorb oil, separate it from water surfaces and transport it on their surfaces (Figure 1, see also the video of the phenomon.).

The observations inspired them to transfer the effect to technical textiles for separating oil and water. The result is a superhydrophobic spacer fabric that can be produced industrially and is therefore easily scalable.

The bio-inspired textile can be integrated into a device for oil-water separation. This entire device is called a Bionic Oil Adsorber (BOA). Figure 2: Cross-section of computer-aided (CAD) model of the Bionic Oil Adsorber. The scheme shows an oil film (red) on a water surface (light blue). In the floating cotainer(gray), the textile (orange) is fixed so that it is in contact with the oil film and the end protrudes into the container. The oil is adsorbed and transported by the BOA textile. As shown in the cross-section, it enters the contain-er, where it is released again and accumulates at the bottom of the container. See also the video regarding the oil absorption on the textile, source ITA).
 
Starting from the contamination in the form of an oil film on the water surface, the separation and collection process works according to the following steps:

  • The BOA is introduced into the oil film.
  • The oil is adsorbed by the textile and separated from the water at the same time.
  • The oil is transported through the textile into the collection container.
  • The oil drips from the textile into the collection container.
  • The oil is collected until the container is emptied.

The advantage of this novel oil separation device is that no additional energy has to be applied to operate the BOA. The oil is separated from the surrounding water by the surface properties of the textile and transported through the textile driven solely by capillary forces, even against gravity. When it reaches the end of the textile in the collection container, the oil desorbs without any further external influence due to gravitational forces. With the current scale approximately 4 L of diesel can be separated from water by one device of the Bionic Oil Adsorber per hour.

  • It seems unlikely that a functionalized knitted spacer textile is cheaper than a conventional nonwoven, like it is commonly used for oil sorbents. However, since it is a functional material, the costs must be related to the amount of oil removed. In this respect, if we compare the sales price of the BOA textile with the sales prices of various oil-binding nonwovens, the former is 5 to 13 times cheaper with 10 ct/L oil removed.
    Overall, the BOA device offers a cost-effective and sustainable method of oil-water separation in contrast to conventional cleaning methods due to the following advantages:
  • No additional energy requirements, such as with oil skimmers, are necessary
  • No toxic substances are introduced into the water body, such as with oil dispersants
  • The textiles and equipment can be reused multiple times
  • No waste remains inside the water body
  • Inexpensive in terms of the amount of oil removed.
  • The team of researchers from the ITA, the University of Bonn and Heimbach GmbH was able to prove that the novel biomimetic BOA technology is surprisingly efficient and sustainable for a self-controlled separation and automatic collection of oil films including their complete removal from the water. BOA can be asapted for open water application but also for the use in inland waters. Furthermore, it is promising, that the textile can be used in various related separation processes. The product is currently being further developed so that it can be launched on the market in 2-3 years.

 

Source:

ITA – Institut für Textiltechnik of RWTH Aachen University

Prof. Dr Tae Jin Kang (Seoul National University), Dr Musa Akdere (CarboScreen), Dr Christian P. Schindler (ITMF), from left to right. Source: ITMF
Prof. Dr Tae Jin Kang (Seoul National University), Dr Musa Akdere (CarboScreen), Dr Christian P. Schindler (ITMF), from left to right.
01.12.2023

Faster and cheaper carbon fibre production with CarboScreen

Faster and more cost-effective carbon fibre production - the technology of the start-up CarboScreen comes a good deal closer to this dream. The founders Dr. Musa Akdere, Felix Pohlkemper and Tim Röding from the Institut für Textiltechnik (ITA) of RWTH Aachen University are using sensor technology to monitor carbon fibre production, thereby doubling the production speed from the current 15 to 30 m/min in the medium term and increasing turnover by up to €37.5 million per year and system. This ground-breaking development also impressed the jury at the ITMF at their Annual Conference in Keqiao, China, and was honoured with the ITMF StartUp Award 2023 on 6 November 2023.

Dr. Musa Akdere accepted the award on behalf of the CarboScreen founding team.

Carbon fibres can only develop their full potential if they are not damaged during production and further processing. Two types of fibre damage occur more frequently during fibre production: Superficial or mechanical damage to the fibres or damage to the chemical structure.

Faster and more cost-effective carbon fibre production - the technology of the start-up CarboScreen comes a good deal closer to this dream. The founders Dr. Musa Akdere, Felix Pohlkemper and Tim Röding from the Institut für Textiltechnik (ITA) of RWTH Aachen University are using sensor technology to monitor carbon fibre production, thereby doubling the production speed from the current 15 to 30 m/min in the medium term and increasing turnover by up to €37.5 million per year and system. This ground-breaking development also impressed the jury at the ITMF at their Annual Conference in Keqiao, China, and was honoured with the ITMF StartUp Award 2023 on 6 November 2023.

Dr. Musa Akdere accepted the award on behalf of the CarboScreen founding team.

Carbon fibres can only develop their full potential if they are not damaged during production and further processing. Two types of fibre damage occur more frequently during fibre production: Superficial or mechanical damage to the fibres or damage to the chemical structure.

Both types of damage cannot be optimally detected by current means or only become apparent after production, to name just two examples. This leads to higher production costs. In an emergency, faulty production can even lead to plant fires. For this reason, and to ensure good production quality, the system is run at 15 m/min below its production capacity for safety reasons. However, 30 m/min or more would be possible. With the sensor-based online monitoring of CarboScreen, the production capacity can be doubled to 30 /min. This would lead to higher production, resulting in lower manufacturing costs and wider use of carbon fibres in mass markets such as automotive, aerospace and wind energy.

More information:
carbon fibers sensors Startup
Source:

ITA – Institut für Textiltechnik of RWTH Aachen University
 

Industriebrache Pixabay; Tama66
19.07.2023

IVC und ZVI positionieren sich klar gegen Pauschalverbot von PFAS

"Viele Unternehmen sitzen bereits auf gepackten Koffern und haben ihre Investitionsentscheidungen sind getroffen." Deutschland sei gerade erneut dabei, sich in multiple internationale Abhängigkeiten zu begeben und seinen Abschied aus dem Kreis der Industrienationen vorzubereiten. So beurteilen der Geschäftsführer der Industrievereinigung Chemiefaser e.V. (IVC), Dr. Wilhelm Rauch, und der Ressortleiter Umwelt-& Chemikalienpolitik des Zentralverbands Oberflächentechnik e.V. (ZVO), Dr. Malte M. Zimmer gemeinsam mit verschiedenen Unternehmen die Konsequenzen aus dem Plan der European Chemicals Agency (ECHA), rund 10.000 Alkylsubstanzen zu verbieten.

"Viele Unternehmen sitzen bereits auf gepackten Koffern und haben ihre Investitionsentscheidungen sind getroffen." Deutschland sei gerade erneut dabei, sich in multiple internationale Abhängigkeiten zu begeben und seinen Abschied aus dem Kreis der Industrienationen vorzubereiten. So beurteilen der Geschäftsführer der Industrievereinigung Chemiefaser e.V. (IVC), Dr. Wilhelm Rauch, und der Ressortleiter Umwelt-& Chemikalienpolitik des Zentralverbands Oberflächentechnik e.V. (ZVO), Dr. Malte M. Zimmer gemeinsam mit verschiedenen Unternehmen die Konsequenzen aus dem Plan der European Chemicals Agency (ECHA), rund 10.000 Alkylsubstanzen zu verbieten.

Die EU lasse dabei die Folgen auf Schlüsseltechnologien wie beispielsweise die grüne Energiewende komplett außer Acht. Lithiumbatterien, Windräder, Brennstoffzellen, Computerchips - für PFAS existierten aktuell zumindest in Hightech-Anwendungen keine Alternativen. Bis auf wenige längere Ausnahmeregelungen seien aktuell 18 Monate als Übergangsfristen vorgesehen. Das sei ein ausreichendes Zeitfenster, um die Produktion in Europa abzuwickeln und nach neuen Standorten zu suchen, beispielsweise in den USA. Dort werde die Fluorchemie als Schlüsseltechnologie massiv aufgebaut und als kostbares Gut mit Exportverboten belegt.

IVC und ZVO monierten, dass das Innovationsvermögen der europäischen Industrie hergeschenkt werde und man anderen Ländern den Markt mit allen preislichen und wettbewerblichen Konsequenzen überlasse. Als besonders betroffene Branchen führten die Verbände die Medizintechnik, Schutzausrüstung, Flugzeugbau und Automobilelektronik, den Textilmaschinenbau und Industrietextilien an. Abluftfilter mit PTFE-Membranen oder aus PTFE-Fasern stellten in der Müllverbrennung und in Zementwerken den Umweltschutz sicher, so dass keine Schadstoffe in die Atmosphäre gelangten. Membranen für Wasserstoff-Brennstoffzellen, Wasserstoffelektrolyseure, Lithium-Ionen-Batterien aus Karbonfaservliesen und der fluorchemischen Protonenaustauscher Nafion-Membran würden in Zukunft verboten und damit die die Pläne für eine Wasserstoffenergiewende dauerhaft nicht umsetzbar.

Source:

Industrievereinigung Chemiefaser e.V., Zentralverband Oberflächentechnik e.V.

OETI purchases ECS to expand its PPE portfolio photo: OETI
12.07.2023

OETI purchases ECS to expand its PPE portfolio

OETI – a member of the internationally active TESTEX Group – has bought the German company ECS to expand its service portfolio in the field of personal protective equipment (PPE).

OETI has been offering testing services for textile work clothing since 1983 – for about 40 years. Since the introduction of CE labelling for personal protective equipment and the enactment of the PPE Directive by the European Union in 1993, OETI has not only been testing textile personal protective equipment, but now on also certifies it in conformity with EU standards. In 1995, OETI was certified in Brussels as a Notified Body (0534) for type-examinations and quality assurance monitoring of personal protective equipment end products. Testing and certification is carried out in accordance with the current PPE Regulation (EU) 2016/425.

Testing and Certification Body for Eye and Face Protection, based in Aalen, was founded 15 years ago and is a globally active institution for testing and certification of eye and face protection equipment. The company is one of the leading independent testing institutions for personal protection products in laser applications and for welding work.

OETI – a member of the internationally active TESTEX Group – has bought the German company ECS to expand its service portfolio in the field of personal protective equipment (PPE).

OETI has been offering testing services for textile work clothing since 1983 – for about 40 years. Since the introduction of CE labelling for personal protective equipment and the enactment of the PPE Directive by the European Union in 1993, OETI has not only been testing textile personal protective equipment, but now on also certifies it in conformity with EU standards. In 1995, OETI was certified in Brussels as a Notified Body (0534) for type-examinations and quality assurance monitoring of personal protective equipment end products. Testing and certification is carried out in accordance with the current PPE Regulation (EU) 2016/425.

Testing and Certification Body for Eye and Face Protection, based in Aalen, was founded 15 years ago and is a globally active institution for testing and certification of eye and face protection equipment. The company is one of the leading independent testing institutions for personal protection products in laser applications and for welding work.

ECS tests and evaluates occupational health and safety goggles with and without a filter action, passive and active switching protection filters and shields for welders, and laser protection filters, goggles, and shields. The company also tests the optical properties of sunglasses, sports glasses, ski goggles, swimming goggles and motorbike goggles.

With OETI’s takeover, the ECS location in Aalen is retained, and all employees will continue working at ECS. The new Managing Director of ECS GmbH as of 1 July 2023 is Dipl.-Ing. Rolf Diebolder.

‘We are present on the European market, on the American market and, via a representative office, on the Chinese market. With the aid of the new distribution channels through OETI and TESTEX, we want to steadily advance ECS’ expansion and be present on all five continents’, says Managing Director Rolf Diebolder, explaining his strategic plans for ECS. ‘I would like OETI and ECS to develop a joint strategy in order to be able to offer existing and new customers of both companies a complete package which, when combined, will give us a unique selling point in the marketplace’, says Diebolder.

Diebolder also sees further potential in the cooperation with regard to protective laser clothing. According to him, this is where the laser laboratory commissioned by ECS could be used to make textiles laser-safe. In the future, there will be more and more ‘hand-held’ devices, i.e. laser welding devices, for which gloves and protective jackets are needed.

Source:

OETI - Institut fuer Oekologie, Technik und Innovation GmbH

Untersuchungsmethoden bei der Zertifizierung von Augenschutzprodukten
Untersuchungsmethoden bei der Zertifizierung von Augenschutzprodukten
11.07.2023

OETI kauft ECS zur Erweiterung des PSA-Portfolios

OETI – Mitglied der international tätigen TESTEX Gruppe – kauft das deutsche Unternehmen ECS, um sein Services-Portfolio im Bereich persönlicher Schutzausrüstungen (PSA) zu erweitern.

Seit rund 40 Jahren bietet das OETI – mit Hauptsitz in Österreich, Prüfungen für textile Arbeitskleidung an. Ab1993, mit der Einführung der CE-Kennzeichnung für persönliche Schutzausrüstung und dem Erlassen der PSA-Richtlinie durch die Europäische Union, prüft das OETI nicht nur textile persönliche Schutzausrüstungen, sondern zertifiziert sie auch EU-konform. Im Jahr 1995 erfolgt OETI‘s Notifizierung in Brüssel als Notified Body (0534) für Baumusterprüfungen und die Überwachung der Qualitätssicherung für das Endprodukt von persönlicher Schutzausrüstung. Geprüft und zertifiziert wird gemäß der aktuellen PSA-Verordnung (EU) 2016/425.

OETI – Mitglied der international tätigen TESTEX Gruppe – kauft das deutsche Unternehmen ECS, um sein Services-Portfolio im Bereich persönlicher Schutzausrüstungen (PSA) zu erweitern.

Seit rund 40 Jahren bietet das OETI – mit Hauptsitz in Österreich, Prüfungen für textile Arbeitskleidung an. Ab1993, mit der Einführung der CE-Kennzeichnung für persönliche Schutzausrüstung und dem Erlassen der PSA-Richtlinie durch die Europäische Union, prüft das OETI nicht nur textile persönliche Schutzausrüstungen, sondern zertifiziert sie auch EU-konform. Im Jahr 1995 erfolgt OETI‘s Notifizierung in Brüssel als Notified Body (0534) für Baumusterprüfungen und die Überwachung der Qualitätssicherung für das Endprodukt von persönlicher Schutzausrüstung. Geprüft und zertifiziert wird gemäß der aktuellen PSA-Verordnung (EU) 2016/425.

Die ECS GmbH - Prüf- und Zertifizierungsstelle für Augen- und Gesichtsschutz mit Sitz in Aalen wurde vor 15 Jahren gegründet und ist eine weltweit agierende Institution für die Prüfung und Zertifizierung von Augen- und Gesichtsschutzgeräten. Für persönliche Schutzprodukte bei Laseranwendungen und für Schweißarbeiten ist das Unternehmen eine der führenden unabhängigen Prüfeinrichtungen.

Die ECS prüft und bewertet Arbeitsschutzbrillen mit und ohne Filterwirkung, passive und aktiv-schaltende Schweißerschutzfilter und -abschirmungen, Laserschutzfilter, -brillen und -abschirmungen. Ebenso prüft das Unternehmen die optischen Eigenschaften von Sonnen-, Sport-, Ski-, Schwimm- und Motorradbrillen.

Nach der Übernahme durch OETI bleibt der ECS-Standort in Aalen erhalten, alle Mitarbeiter*innen sind weiterhin bei der ECS tätig. Neuer Geschäftsführer der ECS GmbH ist ab 1. Juli 2023 Dipl.-Ing. Rolf Diebolder.

„Wir sind auf dem europäischen, auf dem amerikanischen und über eine Vertretung auf dem chinesischen Markt präsent. Mit Hilfe der neuen Vertriebswege durch OETI und TESTEX wollen wir den Ausbau der ECS stetig vorantreiben und auf allen fünf Kontinenten präsent sein.“, so Geschäftsführer Rolf Diebolder.

Weiteres Potenzial in der Zusammenarbeit sieht Diebolder auch in Bezug auf Laserschutzkleidung. Hier könne das von der ECS beauftragte Laserlabor dazu genutzt werden, um Textilien Laserschutz-sicher zu machen. Es wird in Zukunft immer mehr „hand-held“ Geräte geben, also Laserschweißgeräte, für die man Handschuhe und Schutzjacken benötigt.

More information:
OETI PSA
Source:

OETI - Institut fuer Oekologie, Technik und Innovation GmbH

Professor Dr Thomas Gries with the award winner Flávio André Marter Diniz Hanns-Voith-Stiftung, Oliver Voge
Professor Dr Thomas Gries with the award winner Flávio André Marter Diniz
11.07.2023

Future cost reduction through ultra-thin PE carbon fibres

  • ITA Master's graduate wins Hanns Voith Foundation Award 2023

In his Master's thesis, Flávio André Marter Diniz, a graduate of the Institut für Textiltechnik of RWTH Aachen University (ITA), developed ultra-thin polyethylene (PE) carbon fibres with a filament diameter 2-3 times smaller than usual. In addition, the use of PE-based precursors will make it possible to reduce the price of carbon fibres by 50 per cent in the future, thus opening up a wide range of other possible applications in key industries such as wind power, aerospace and automotive. For this groundbreaking development, Marter Diniz was awarded the Hanns Voith Prize with the Hanns Voith Foundation Award in the category "New Materials". The prize is endowed with € 5,000 in prize money.

Flávio André Marter Diniz won the prize in the category "New Materials" for his master thesis entitled "Investigation of the stabilisation and carbonisation process for the production of ultra-thin polyethylene-based carbon fibres".

  • ITA Master's graduate wins Hanns Voith Foundation Award 2023

In his Master's thesis, Flávio André Marter Diniz, a graduate of the Institut für Textiltechnik of RWTH Aachen University (ITA), developed ultra-thin polyethylene (PE) carbon fibres with a filament diameter 2-3 times smaller than usual. In addition, the use of PE-based precursors will make it possible to reduce the price of carbon fibres by 50 per cent in the future, thus opening up a wide range of other possible applications in key industries such as wind power, aerospace and automotive. For this groundbreaking development, Marter Diniz was awarded the Hanns Voith Prize with the Hanns Voith Foundation Award in the category "New Materials". The prize is endowed with € 5,000 in prize money.

Flávio André Marter Diniz won the prize in the category "New Materials" for his master thesis entitled "Investigation of the stabilisation and carbonisation process for the production of ultra-thin polyethylene-based carbon fibres".

The use of carbon fibres in highly stressed lightweight construction solutions, such as today's growth applications of wind turbines or pressure tanks, has become indispensable due to their excellent mechanical properties and low density. High manufacturing costs of conventional PAN precursor-based carbon fibres make the material very cost-intensive. In addition, it is not sufficiently available. New manufacturing approaches that develop alternative raw materials and manufacturing processes can be a key and growth engine for further industrial composites applications.

The aim of the work was to develop a new and cost-effective manufacturing process for high-quality ultra-thin carbon fibres using a polyethylene precursor. For this purpose, the sulphonisation process, which is time-consuming today, was to be significantly shortened. As a result, Mr. Marter Diniz produced novel ultra-thin polyethylenebased carbon fibres with a filament diameter < 3 μm with an excellent surface quality of the fibres without detectable structural defects. The fibre diameter is 2-3 times smaller than that of conventional PANbased CF. This provides the basis for mechanically high-quality material properties. At the same time, Mr. Marter Diniz was able to reduce the sulphonisation time by 25 percent. The developed material and technology set important milestones on the way to cheaper carbon fibres. With PE-based precursors, the price of CF can be reduced by 50 percent compared to conventional PAN-based CF.  

A total of five other young scientists were awarded in six categories (Drive Technology, Innovation & Technology/Artificial Intelligence, New Materials, Paper, Hydropower and Economic Sciences. This year, for the 10th time, the Hanns Voith Foundation awarded the Hanns Voith Prize to outstanding young scientists.

Source:

ITA Institut für Textiltechnik of RWTH Aachen University

Dr Ioana Slabu and Benedict Bauer with the nanomodified stent. Photo Peter Winandy
30.03.2023

Nanomodified polymerstent: Novel technology for tumour therapy

  • Electromagnetically heatable nanomodified stent for the treatment of hollow organ tumours wins second place at the RWTH Innovation Award

Almost every fourth person who dies of cancer has a hollow organ tumour, for example in the bile duct or in the oesophagus. Such a tumour cannot usually be removed surgically. It is only possible to open the hollow organ for a short time using a stent, i.e. a tubeshaped prosthesis. However, the tumour grows back and penetrates the hollow organ through the stent. Ioana Slabu from the Institute of Applied Medical Technology and Benedict Bauer from the Institut für Textiltechnik of RWTH Aachen University have now developed a novel technology for the therapy of hollow organ tumours, which was awarded second place in the RWTH Innovation Award. This involves a polymerstent that contains magnetic nanoparticles. When electromagnetic fields are applied, these nanoparticles lead to a controlled heating of the stent material and thus of the tumour. Because the tumour reacts much more sensitively to heat than healthy tissue, it is destroyed and the hollow organ remains open. Thus, the stent develops a self-cleaning effect.  

  • Electromagnetically heatable nanomodified stent for the treatment of hollow organ tumours wins second place at the RWTH Innovation Award

Almost every fourth person who dies of cancer has a hollow organ tumour, for example in the bile duct or in the oesophagus. Such a tumour cannot usually be removed surgically. It is only possible to open the hollow organ for a short time using a stent, i.e. a tubeshaped prosthesis. However, the tumour grows back and penetrates the hollow organ through the stent. Ioana Slabu from the Institute of Applied Medical Technology and Benedict Bauer from the Institut für Textiltechnik of RWTH Aachen University have now developed a novel technology for the therapy of hollow organ tumours, which was awarded second place in the RWTH Innovation Award. This involves a polymerstent that contains magnetic nanoparticles. When electromagnetic fields are applied, these nanoparticles lead to a controlled heating of the stent material and thus of the tumour. Because the tumour reacts much more sensitively to heat than healthy tissue, it is destroyed and the hollow organ remains open. Thus, the stent develops a self-cleaning effect.  

Ioana Slabu of the AME explains: "Not only can we drastically reduce treatment costs, but above all we can provide relief for millions of patients worldwide.
 
A manufacturing process and proof of concept for magnetic hyperthermia are already in place. This novel technology has a very high development potential because it can also be used for tumours in other parts of the body such as the prostate, stomach, intestine or urinary bladder or for cardiovascular diseases.  

The AiF/IGF project started under the project title "ProNano" funded by BMWK. Now the approval for the follow-up project "ProNano2" has also been received. The approved project is called: "Validation of the innovation potential of heatable stents for heat-induced treatment of cavity tumours" and is funded by BMBF in course of the VIP+ program. With the Clinic for General, Visceral and Transplantation Surgery of the University Hospital Aachen and the Institute for Technology and Innovation Management at RWTH Aachen University, the consortium is enriched by clinical and economic expertise. Every year, RWTH Aachen University honours particularly innovative university projects with the Innovation Award. Professor Malte Brettel, Prorector for Business and Industry, presented the certificates to four outstanding projects as part of RWTHtransparent.

Source:

ITA – Institut für Textiltechnik of RWTH Aachen University

(c) BRÜCKNER
The project team of BRÜCKNER and HEATHCOAT in BRÜCKNER’s Technology Centre in Leonberg
04.10.2022

BRÜCKNER: New finishing line for British company HEATHCOAT FABRICS

HEATHCOAT FABRICS partnered again with BRÜCKNER Textile Technologies and their sales partner ADVANCED DYEING SOLUTIONS to install a finishing line for industrial textiles. HEATHCOAT FABRICS specializes in the production of technical textiles in the fields of texturising, weaving and warp knitting as well as dyeing and finishing. The prroducts are manufactured for use in the automotive, healthcare, defence, and aerospace industries

Mrs. Regina Brückner, CEO and owner of the BRÜCKNER Group stated: "To meet the complex re-quirements of HEATHCOAT is not easy because of the great variety of technical textiles produced. Our line has to finish light as well as heavy articles, so the design, control and the whole line layout have to be flexible, functional and still easy to operate. Fortunately, the team at HEATHCOAT FABRICS is very innovative and open-minded, and together we worked hard to develop the right technology and han-dling. We are very happy that we could convince this customer, whom we appreciate very much, with the productivity of our line and of course with our technological know-how."

HEATHCOAT FABRICS partnered again with BRÜCKNER Textile Technologies and their sales partner ADVANCED DYEING SOLUTIONS to install a finishing line for industrial textiles. HEATHCOAT FABRICS specializes in the production of technical textiles in the fields of texturising, weaving and warp knitting as well as dyeing and finishing. The prroducts are manufactured for use in the automotive, healthcare, defence, and aerospace industries

Mrs. Regina Brückner, CEO and owner of the BRÜCKNER Group stated: "To meet the complex re-quirements of HEATHCOAT is not easy because of the great variety of technical textiles produced. Our line has to finish light as well as heavy articles, so the design, control and the whole line layout have to be flexible, functional and still easy to operate. Fortunately, the team at HEATHCOAT FABRICS is very innovative and open-minded, and together we worked hard to develop the right technology and han-dling. We are very happy that we could convince this customer, whom we appreciate very much, with the productivity of our line and of course with our technological know-how."

The direct gas heated BRÜCKNER POWER-FRAME stenter with its staggered heating source arrangement every half zone provides best available temperature consistency across the length and the width of the stenter. The unit is equipped with a low-lub, horizontally returning combined pin / clip chain and several fabric paths, especially designed for the different fabrics being processed. Together with HEATHCOAT FABRICS technologists, the BRÜCKNER design team developed a special delivery end of the stenter with different edge trimming and slitting possibilities. Depending on the kind of products, the fabrics can be batched on large diameter A-frames, wound on cardboard tubes or plaited into trolleys.

Source:

Brückner Trockentechnik GmbH & Co. KG

(c) Fraunhofer IAP
Faserverstärktes Monomaterialkomposit aus PLA
28.07.2022

Fraunhofer CCPE: Technische Produktinnovationen für eine zirkuläre Kunststoffwirtschaft

Ziel des Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE ist es, die Wertschöpfungskette Kunststoff zirkulär zu gestalten. Sechs Fraunhofer-Institute erforschen am Beispiel Kunststoff, wie der Wandel von einer linearen zur einer zirkulären Kunststoffwirtschaft gelingen kann. Auf der ACHEMA in Frankfurt, der internationalen Messe für die Prozessindustrie, stellt das Fraunhofer CCPE vom 22. bis zum 26. August zwei technische Produktinnovationen und ein Bewertungstool für Unternehmen der Circular Economy vor.

Seit 2018 erforschen die sechs Fraunhofer-Institute — IAP, ICT, IML, LBF, IVV und UMSICHT – wie eine nachhaltige Transformation einer gesamten Wertschöpfungskette unter Prinzipien der Circular Economy erfolgen kann. Durch einen Multi-Stakeholder-Ansatz können FuE-Kompetenzen gebündelt werden, um Produkte zirkulär zu gestalten, passende Geschäftsmodelle zu entwickeln und End-of-Life Verluste bei Kunststoffabfällen zu reduzieren. Auf der ACHEMA werden die folgenden Projekte ausgestellt:

Ziel des Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE ist es, die Wertschöpfungskette Kunststoff zirkulär zu gestalten. Sechs Fraunhofer-Institute erforschen am Beispiel Kunststoff, wie der Wandel von einer linearen zur einer zirkulären Kunststoffwirtschaft gelingen kann. Auf der ACHEMA in Frankfurt, der internationalen Messe für die Prozessindustrie, stellt das Fraunhofer CCPE vom 22. bis zum 26. August zwei technische Produktinnovationen und ein Bewertungstool für Unternehmen der Circular Economy vor.

Seit 2018 erforschen die sechs Fraunhofer-Institute — IAP, ICT, IML, LBF, IVV und UMSICHT – wie eine nachhaltige Transformation einer gesamten Wertschöpfungskette unter Prinzipien der Circular Economy erfolgen kann. Durch einen Multi-Stakeholder-Ansatz können FuE-Kompetenzen gebündelt werden, um Produkte zirkulär zu gestalten, passende Geschäftsmodelle zu entwickeln und End-of-Life Verluste bei Kunststoffabfällen zu reduzieren. Auf der ACHEMA werden die folgenden Projekte ausgestellt:

  • Faserverstärktes Monomaterialkomposit aus PLA
    Biobasierte Kunststoffe werden zunehmend für technisch anspruchsvolle Einsatzbereiche z.B. in der Automobil- und Textilindustrie nachgefragt. Zwei zentrale Anforderungen sind dabei ihre Stabilität und ihre Recyclingfähigkeit. Forschende der Fraunhofer-Institute IAP und ICT entwickelten innovative PLA-basierte Monomaterial-Komposite (Organobleche), die technische Applikationen adressieren und insbesondere mit Hinblick auf die Rezyklisierbarkeit einen Beitrag zur Umsetzung der Sustainable Development Goals der UN leisten können.
  • Optisch und mechanisch verbesserte Folienrezyklate
    Bei der Herstellung von Folien zählt neben den mechanischen Eigenschaften besonders der visuelle Eindruck. Es dürfen keine Fehlstellen in Form von Stippen, Fischaugen oder Abrissen auftreten, die insbesondere bei Verwendung von Rezyklaten zu Problemen führen können. Die direkte Verwendung eines Folienregranulats führt jedoch häufig zu vielen Abrissen während der Folienherstellung, die zudem fatale Auswirkungen auf die mechanischen Materialeigenschaften haben. Durch die Zugabe einer geeigneten Additivformulierung konnte die Folienqualität nun signifikant verbessert werden.

Ist ein Produkt reif für die Circular Economy?
Weiterhin präsentieren die Forschenden nun auf der ACHEMA das webbasierte Tool CRL®, mit dem Unternehmen den Reifegrad von Produkten oder Produktsystemen im Hinblick auf die Circular Economy selbst bewerten können. Es prüft, inwieweit ein Produkt die Strategien der Kreislaufwirtschaft in den Bereichen Produktdesign, Produktdienstleistungssystem, End-of-Life-Management und Kreislaufwirtschaft bereits berücksichtigt und wo noch Verbesserungspotenzial besteht.

Source:

Fraunhofer-Institut für Umwelt-, Sicherheits- und Energietechnik UMSICHT

(c) ITM
22.06.2022

ITM: Techtextil Innovation Award 2022 für neuartige textile Herzklappenprothesen

Wissenschaftler:innen vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden sind am 21. Juni 2022 für ihre gewebten Herzklappenimplantate mit dem Techtextil Innovation Award 2022 in der Kategorie „New Product“ ausgezeichnet worden.

Im Rahmen eines Forschungsprojektes der Industriellen Gemeinschaftsforschung (IGF) entwickelten Wissenschaftler:innen des ITM neuartige textile Herzklappenprothesen. Die Implantate können exakt an die anatomische Form angepasst und minimalinvasiv im Herz platziert werden. Die textile Herzklappe ist integral gefertigt. Hierbei erfolgt die Integration des Ventils in situ während des Webprozesses. Somit besteht die strömungstechnisch optimierte Herzklappe aus einer einzigen textilen Struktur. Weitere Fügeprozesse, z. B. durch Nähen, sind nicht mehr erforderlich. Das reduziert den Fertigungsaufwand im Gegensatz zur heutigen Herstellung biologischer Herzklappenprothesen in Handarbeit enorm.

Wissenschaftler:innen vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden sind am 21. Juni 2022 für ihre gewebten Herzklappenimplantate mit dem Techtextil Innovation Award 2022 in der Kategorie „New Product“ ausgezeichnet worden.

Im Rahmen eines Forschungsprojektes der Industriellen Gemeinschaftsforschung (IGF) entwickelten Wissenschaftler:innen des ITM neuartige textile Herzklappenprothesen. Die Implantate können exakt an die anatomische Form angepasst und minimalinvasiv im Herz platziert werden. Die textile Herzklappe ist integral gefertigt. Hierbei erfolgt die Integration des Ventils in situ während des Webprozesses. Somit besteht die strömungstechnisch optimierte Herzklappe aus einer einzigen textilen Struktur. Weitere Fügeprozesse, z. B. durch Nähen, sind nicht mehr erforderlich. Das reduziert den Fertigungsaufwand im Gegensatz zur heutigen Herstellung biologischer Herzklappenprothesen in Handarbeit enorm.

Prof. Chokri Cherif, Institutsdirektor des ITM, freut sich mit seinem Team sehr über die kontinuierli-chen interdisziplinären Forschungserfolge, die am ITM in enger Kooperation mit technischen Webereien, Medizinern und Anwendern stetig erzielt werden. „Bereits vor zwei Jahren wurden wir mit dieser neuartigen Entwicklung als eines der drei Finalistenteams des Otto von Guericke-Preises 2020 geehrt. Die Auswahl für den Techtextil Innovation Award 2022 ist eine erneute Bestätigung für den Bedarf an unserer praxisorientierten Forschung und eine besondere Würdigung, aber gleichzeitig auch weiterer Ansporn für die zeitnahe Umsetzung unserer Forschungsergebnisse in die Industrie.“

Bislang stehen für die Behandlung defekter Herzklappen mechanische und biologische Klappen zur Verfügung. Die neuartigen gewebten Herzklappenprothesen sollen die Vorteile der beiden Typen vereinen: unbegrenzte Lebensdauer, keine lebenslange Einnahme von blutverdünnenden Medikamenten und minimal invasive Operation. Ferner können die textilen Herzklappen zeit- und kostensparend mit hoher Reproduzierbarkeit und Qualität gefertigt werden.

ECO-COAT minimum application unit (c) Brückner
Minimalauftragsaggregat ECO-COAT
02.06.2022

BRÜCKNER: Answering current challenges of the textile industry

The German machinery producer BRÜCKNER used exactly these chances and repositioned itself during the pandemic period. For more than 70 years, the family-run company has been specialized in individual finishing concepts for textiles, technical textiles, nonwovens and floor coverings. The current challenges in the textile industry are serious. The clear increase of the energy costs and the general uncertainty of the energy supply as well as political requirements make a profitable textile production more and more demanding for many companies.

The German machinery producer BRÜCKNER used exactly these chances and repositioned itself during the pandemic period. For more than 70 years, the family-run company has been specialized in individual finishing concepts for textiles, technical textiles, nonwovens and floor coverings. The current challenges in the textile industry are serious. The clear increase of the energy costs and the general uncertainty of the energy supply as well as political requirements make a profitable textile production more and more demanding for many companies.

The company responds to this with a newly developed stenter concept with double heating system. Depending on availability, the lines can be operated with gas or oil, but also other combinations with steam or renewable energies are possible. This means that production delays and machine downtimes can be avoided as far as possible. In addition, developed intelligent assistance systems for its machines have been developed that support the machine operator in using the best possible process to operate the line as energy-efficiently as possible. Further energy savings are possible with new energy-efficient motors or heat-recovery and exhaust air cleaning systems. This also helps to avoid harmful emissions.

But many textile producers are also focusing on reducing chemicals. For this purpose, BRÜCKNER's further developed ECO-COAT minimum application unit can make a decisive contribution. Knitted and woven fabrics, but also nonwovens can be finished on one or both sides via different fabric paths. With the minimum application via an engraved roller, a single-sided application of up to 100 g/m² can be achieved. A double-sided and higher application quantity is achieved, for example, by impregnation in the nip. Irrespective of the selected fabric path, a very small liquor reservoir means that only minimal quantities of waste water are produced when changing batches or liquors, and the use of chemicals can also be significantly reduced. In addition, less water has to be evaporated in the subsequent drying process than, for example, in the case of impregnation in a water bath, so the energy requirement is significantly reduced.

On the two upcoming trade fairs ITM in Istanbul and TECHTEXTIL in Frankfurt in June, interested customers can personally get an idea of BRÜCKNER's new developments.

Source:

Brückner Trockentechnik GmbH & Co. KG

(c) AVK - Industrievereinigung Verstärkte Kunststoffe e. V.
24.11.2021

The AVK – Industrievereinigung Verstärkte Kunststoffe – presents its Innovation Awards 2021

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

The AVK – Industrievereinigung Verstärkte Kunststoffe – has once again presented its Innovation Awards to companies, institutes and their partners. Three composites innovations were recognised in each of the three categories – “Innovative Products/Applications”, “Innovative Processes” and “Research and Science” – at the new event JEC Forum DACH on 23 November 2021, the first edition of which was held in Frankfurt.

“As usual, the submissions included a lot of very interesting and promising products and processes this year. The Innovation Awards highlight the outstanding efficiency, cost-effectiveness and sustainability of fibre-reinforced plastics as well as the companies and institutes operating in the sector,” explains Dr. Elmar Witten, Managing Director of the AVK. The jury of leading experts from the industry honoured the following innovations this year:

Category “Research and Science”
First place in the “Research and Science” category was awarded to the German Aerospace Center (DLR) for its Bondline Control Technology (BCT). This innovative process is used for quality control and assurance of bonded joints. The core element is a porous fabric which is applied to a joining surface using an epoxy adhesive or matrix resin. Peeling away the fabric creates a chemically reactive and undercut surface and can also be used as a test to check adhesion to the substrate. BCT has potential in a variety of possible applications. For example, peel ply can be replaced by BCT fabric to produce composite components with an optimised joining surface. The cost-effective BCT peel test is suitable for coupon testing and process control. In addition, the combined adhesion test and surface pre-treatment can be used for quality assurance of bonded repairs on fibre composite structures.

Second place was taken by the Institute of Textile Technology (ITA) at RWTH Aachen University and its partners AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR with “StoneBlade – Lightweight construction with granite for the wind industry”. This innovation enables manufacturers to reduce the amount of non-recyclable materials used in rotor blade construction. At the same time, it reduces the weight of these components and improves the mechanical properties relating to the stability of wind turbines. The innovative approach replaces glass-fibre reinforced plastic in the blade components with hard rock – a natural, cost-effective and recyclable lightweight material. The slabs of rock are cut and ground to a thickness of just a few millimetres and embedded in a fibre composite laminate with carbon fibre, which stabilises them for alternating load cases. The pre-stressed material is pressure-stable in the composite and can absorb tensile forces in the event of continuously alternating loads without any loss of stiffness.

Third place went to the Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK) with its partner Mercedes Benz AG for the interdisciplinary development of a highly integrated inductive charging module for electric vehicles. The ultra-thin charging module was designed to make optimum use of space in the vehicle underbody without reducing ground clearance. An interdisciplinary approach was adopted for the development process. This involved the electrical, mechanical and process characterisation of high-frequency Litz wires, ferromagnetic foil and metal wire cloth as well as the creation of a simulation model. The result is a demonstrator for a charging system with a structural height of 15 mm and a total weight of 8 kg. It achieves a transmission efficiency of up to 92 percent at 7.2 kW nominal power and active air cooling. The hardware demonstrator was fabricated in a 3-step process using RTM and VARI techniques.

Overview of all the winners in the three categories:
Category “Innovative Products/Applications”
1st Place: “Traffic signs from Nabasco (N-BMC)” – Nabasco Products BV and Lorenz Kunststofftechnik GmbH, partners: Pol Heteren BV and NPSP BV
2nd Place: “Novel, ultratough vinyl ester resin for the construction of large marine vessels” Evonik Operations GmbH
3rd Place: “Air intake housing with a multi-material design for gas turbines” – MAN Energy Solutions SE, Leichtbau-Zentrum Sachsen GmbH and Leichtbau-Systemtechnologien KORROPOL GmbH.
Category “Innovative Processes”
1st Place: “In-mould wrapping” off-tool, film-coated, fibre composite components for exterior applications – BMW Group, Partner: Renolit SE
2nd Place: “Adaptive automated repair of composite structural components in the aviation sector” – Lufthansa Technik AG, Partner: iSAM AG
3rd Place: “Automated surface pre-treatment using VUV excimer lamps” – CTC GmbH
Category “Research and Science”
1st Place: “Bondline Control Technology (BCT)” – German Aerospace Center (DLR)
2nd Place: “StoneBlade – Lightweight construction with granite for the wind industry” – Institute of Textile Technology at RWTH Aachen University, Partners: AEROVIDE GmbH, Altropol Kunststoff GmbH, Basamentwerke Böcke GmbH, TechnoCarbon Technologies GbR
3rd Place: “Interdisciplinary development of a highly integrated inductive charging module for electric vehicles” – Dresden University of Technology – Institute for Lightweight Construction and Plastics Technology (ILK), Partner: Mercedes Benz AG

Submissions for the next Innovation Award can be made from the end of January 2022.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

Fraunhofer UMSICHT: Bionische Mikroplastikfilter in Waschmaschinen (c) Jan Hagenmeyer/Uni Bonn
06.10.2021

Fraunhofer UMSICHT: Bionische Mikroplastikfilter in Waschmaschinen

In der Waschmaschine wird nicht nur die Wäsche sauber. Durch den Abrieb von Synthetikfasern gelangen mit dem Abwasser auch winzige Kunststoffpartikel in die Umwelt. Biologinnen und Biologen der Universität Bonn wollen zusammen mit dem Fraunhofer UMSICHT und der Firma Hengst nach dem Vorbild von Fischkiemen einen effizienten, nachhaltigen und haltbaren Waschmaschinenfilter entwickeln. Das Projekt »FishFlow« wird vom Bundesministerium für Bildung und Forschung (BMBF) für ein Jahr mit rund 500 000 Euro gefördert.

Im Fokus stehen Filtertechnologien, die die Verbreitung der unter fünf Millimeter kleinen Kunststoffteilchen unterbinden. Wissenschaftlerinnen und Wissenschaftler der Universität Bonn nehmen nun das Maul von Fischen als biologisches Vorbild für neuartige Filter. »Es gibt viele filtrierende Tiere, aber der Apparat der Fische, von den Kiemenbögen bis zur Weiterleitung der Nahrung in den Verdauungstrakt, weist im Vergleich die höchste Ähnlichkeit zu den Verhältnissen in der Waschmaschine auf«, sagt Prof. Alexander Blanke vom Institut für Evolutionsbiologie und Ökologie der Universität Bonn.

In der Waschmaschine wird nicht nur die Wäsche sauber. Durch den Abrieb von Synthetikfasern gelangen mit dem Abwasser auch winzige Kunststoffpartikel in die Umwelt. Biologinnen und Biologen der Universität Bonn wollen zusammen mit dem Fraunhofer UMSICHT und der Firma Hengst nach dem Vorbild von Fischkiemen einen effizienten, nachhaltigen und haltbaren Waschmaschinenfilter entwickeln. Das Projekt »FishFlow« wird vom Bundesministerium für Bildung und Forschung (BMBF) für ein Jahr mit rund 500 000 Euro gefördert.

Im Fokus stehen Filtertechnologien, die die Verbreitung der unter fünf Millimeter kleinen Kunststoffteilchen unterbinden. Wissenschaftlerinnen und Wissenschaftler der Universität Bonn nehmen nun das Maul von Fischen als biologisches Vorbild für neuartige Filter. »Es gibt viele filtrierende Tiere, aber der Apparat der Fische, von den Kiemenbögen bis zur Weiterleitung der Nahrung in den Verdauungstrakt, weist im Vergleich die höchste Ähnlichkeit zu den Verhältnissen in der Waschmaschine auf«, sagt Prof. Alexander Blanke vom Institut für Evolutionsbiologie und Ökologie der Universität Bonn.

Zusammen mit dem Fraunhofer UMSICHT in Oberhausen und der Firma Hengst in Münster starten die Forschenden ein Projekt, mit dem die Strukturen der Fische nachempfunden werden sollen.

Ziel des Forschungsteams ist ein Filter, der möglichst lange hält, nachhaltig gefertigt ist und eine Rückhalteeffizienz von mehr als 90 Prozent aufweist.

Source:

Fraunhofer-Institut für Umwelt-, Sicherheits- und Energietechnik UMSICHT

ITA
04.05.2021

2021 Aachen Reinforced! Symposium free of charge for all attendees

Institut für Textiltechnik of RWTH Aachen University has changed the format of the 2021 Aachen Reinforced! Symposium to an online only format. The programme was shortened to suit the new format, with presentations taking place on Monday 10th May and Tuesday 11th May.

Institut für Textiltechnik of RWTH Aachen University has changed the format of the 2021 Aachen Reinforced! Symposium to an online only format. The programme was shortened to suit the new format, with presentations taking place on Monday 10th May and Tuesday 11th May.

The conference program for Monday, 10th May:
The programme will begin with exciting presentations on glass chemistry and fibres. A talk by Dr Anne Berthereau (Owens Corning Composites) on the race for always higher modulus glass fibres will be followed by a talk from Dr Hong Li (Nippon Electric Glass) on the potential of new high-strength and high-modulus glass fibres.
After two further presentations on high modulus and bioactive glass fibres from Muawia Dafir and Julia Eichhorn (TU Bergakademie Freiberg), we will learn about furnace efficiency as well as process monitoring and digitalisation in glass fibre production from René Meulemann (CelSian), Hans Gedon (Gedonsoft) and Julius Golovatchev (Incotelogy) respectively.
A presentation by Felix Quintero Martínez (Universidade de Vigo) will explore a novel method to produce ultra-flexible glass nanofibers.
The afternoon will continue with two presentations by Dr Christina Scheffler (Leibniz-Institut für Polymerforschung Dresden e.V. (IPF)) and Professor James Thomason (University of Strathclyde) in the field of glass fibre sizings and fibre-matrix interfaces. Finally, a closing presentation by Steve Bassetti (Michelman) will conclude the first day of the Symposium.

The entire conference programme is available on the website https://aachen-fibres.com/aachen-reinforced/general-information.
To register for the Symposium, use the following link: https://aachen-fibres.com/aachen-reinforced/registration

Nach rund 45 Jahren am Standort in der Spengergasse in Wien ist das OETI (Institut fuer Oekologie, Technik und Innovation GmbH) nun umgezogen! (c) OETI
Entwurf Forum Architekten
17.03.2021

OETI zieht um!

  • Nach rund 45 Jahren am Standort in der Spengergasse in Wien ist das OETI (Institut fuer Oekologie, Technik und Innovation GmbH) nun umgezogen!
  • In knapp vier-jähriger intensiver Planungs- und Bauzeit wurde ein Niedrigenergie-Neubau, der CO2 neutral betrieben wird, errichtet.

Ab 15.03.2021: Klimafreundlicher, vollwertiger Laborstandort innerhalb der TESTEX Gruppe

  • Nach rund 45 Jahren am Standort in der Spengergasse in Wien ist das OETI (Institut fuer Oekologie, Technik und Innovation GmbH) nun umgezogen!
  • In knapp vier-jähriger intensiver Planungs- und Bauzeit wurde ein Niedrigenergie-Neubau, der CO2 neutral betrieben wird, errichtet.

Ab 15.03.2021: Klimafreundlicher, vollwertiger Laborstandort innerhalb der TESTEX Gruppe

Das „OETI – Institut fuer Oekologie, Technik und Innovation GmbH“ wurde vor fast 55 Jahren gegründet und ist ein Prüfinstitut für Textilien, persönliche Schutzausrüstungen und Fußbodentechnik mit Hauptsitz in Wien und 13 weiteren Niederlassungen weltweit. Darüber hinaus ist das OETI Gründungsmitglied der Internationalen OEKO-TEX® - Gemeinschaft. Die Internationale Gemeinschaft für Forschung und Prüfung auf dem Gebiet der Textil- und Lederökologie bietet unabhängige Zertifizierungen und Produktlabels. Seit 1992 ermöglicht OEKO-TEX® Unternehmen entlang der textilen und Leder-Kette und allen Verbraucherinnen und Verbrauchern, verantwortungsvolle Entscheidungen für gesundheitlich unbedenkliche, umweltfreundliche und fair hergestellte Produkte zu treffen.

Passend zu diesem Nachhaltigkeitsfokus, war es dem OETI und seiner Muttergesellschaft, der Schweizer TESTEX AG, ein Anliegen das neue OETI-Hauptquartier in Niedrigenergiebauweise zu errichten und CO2-neutral zu betreiben. Um diese Ziele zu erreichen, wurden höchste Wärmedämmung und energietechnische Optimierung eingesetzt, während die CO2-neutrale Stromversorgung aus der hauseigenen Photovoltaikanlage und durch heimische erneuerbare Energie gespeist wird.

Das neue Hauptquartier bietet bis zu 75 Mitarbeiterinnen und Mitarbeitern auf 2.500m2 Platz und beeindruckt mit hellen und technisch bestens ausgestatteten Büroflächen. Auch die Laborbereiche, das analytisch/chemische Labor und das mechanische Labor, wurden nach den neusten Methoden und Techniken konzipiert. Damit wird das OETI, neben seiner Schweizer Muttergesellschaft TESTEX AG, zum zweiten vollwertigen Laborstandort innerhalb der gesamten, globalen TESTEX Gruppe.

Details zu Planung und Bau

Aufgrund des guten Geschäftserfolges entscheidet sich das OETI im Jahr 2017 den Hauptsitz in Wien auszubauen und erwirbt noch im selben Jahr ein Grundstück für den Bau eines eigenen Geschäftsgebäudes in Liesing, dem 23. Wiener Gemeindebezirk. Der Neubau soll dem innovativen Geist des Prüfinstitutes gerecht werden. Deshalb schreibt das OETI einen Wettbewerb aus und entscheidet sich aus zahlreichen Bewerbern für das österreichische Architekturbüro „Forum Architekten“. „Forum Architekten“ ist bekannt für seine kreativen Lösungsfindungen und hat bereits unterschiedlichste Gebäude vom Flughafenterminal, bis hin zum Hörsaal und privaten Wohnbauten entworfen.
Nach intensiver Planungsphase startet das Projekt im Oktober 2019 in die Bauphase. Um trotz anhaltender Pandemie den Zeitplan für den Einzug Mitte März 2021 halten zu können, arbeiten zeitweise rund 70 Handwerker auf der Baustelle.

Source:

Gerda Pongratz, Marketing & PR

Vötsch Industrietechnik GmbH: Infrarot für textile Prozesse (c) Vötsch Industrietechnik GmbH
07.01.2021

Vötsch Industrietechnik GmbH: Infrarot für textile Prozesse

In der Textilverarbeitung ist Infrarot-Strahlung eine bewährte Wärmequelle. Sie überträgt kontaktlos hohe Leistungen in kurzer Zeit. Dadurch kann Energie eingespart und die Produktionsgeschwindigkeit erhöht werden. Letztlich werden die Produktionskosten minimiert. Infrarotsysteme sind sehr kompakt und können eine hohe Leistungsdichte auf einer kleinen Fläche erzeugen. Daraus resultieren kleine Anlagenlayouts und ein geringer Platzbedarf in der Produktion.

  • Infrarot-Strahler übertragen Wärme kontaktfrei
  • Kurze Reaktionszeiten erlauben eine exakte Temperaturführung
  • Optimal abgestimmte Infrarot-Strahlersysteme erhöhen die Prozessgeschwindigkeit, verbessern die Qualität und sparen Energie

Fixierung von Teppich Bahnen bestehend aus Textilgewebe und Bitumen Laminierung
Durch die Verwendung von Infrarot wird stets eine konstante Bitumentemperatur beim Laminieren mit dem Textilsubstrat gewährleistet unabhängig von der Produktionsgeschwindigkeit (sogar nach Maschinenstillstand) und unabhängig von der Umgebungstemperatur. Dadurch wurde das Problem der Delamination gelöst.

In der Textilverarbeitung ist Infrarot-Strahlung eine bewährte Wärmequelle. Sie überträgt kontaktlos hohe Leistungen in kurzer Zeit. Dadurch kann Energie eingespart und die Produktionsgeschwindigkeit erhöht werden. Letztlich werden die Produktionskosten minimiert. Infrarotsysteme sind sehr kompakt und können eine hohe Leistungsdichte auf einer kleinen Fläche erzeugen. Daraus resultieren kleine Anlagenlayouts und ein geringer Platzbedarf in der Produktion.

  • Infrarot-Strahler übertragen Wärme kontaktfrei
  • Kurze Reaktionszeiten erlauben eine exakte Temperaturführung
  • Optimal abgestimmte Infrarot-Strahlersysteme erhöhen die Prozessgeschwindigkeit, verbessern die Qualität und sparen Energie

Fixierung von Teppich Bahnen bestehend aus Textilgewebe und Bitumen Laminierung
Durch die Verwendung von Infrarot wird stets eine konstante Bitumentemperatur beim Laminieren mit dem Textilsubstrat gewährleistet unabhängig von der Produktionsgeschwindigkeit (sogar nach Maschinenstillstand) und unabhängig von der Umgebungstemperatur. Dadurch wurde das Problem der Delamination gelöst.

Trocknung von Baumwollgewebe auf 2% Restfeuchte
Das System erzeugt eine konstante Restfeuchte bei variierender Produktionsgeschwindigkeit von 10-100m/min und über die vollständige Gewebebreite.
Der Trockenofen ist vertikal aufgebaut, wodurch sehr wenig Platz von nur 1m für 200kW benötigt wurde.

Vorwärmung von Nadelfilz Matten
Das Gewebe wird über die gesamte Produktionsbreite von 5000mm am Eingang des Umluftofens mit einer erhöhten Temperatur (± 60°C zusätzlich) angeliefert, und zwar unabhängig von der Produktionsgeschwindigkeit. Die Prozess Geschwindigkeit konnte auf 12m/min. erhöht werden.
Nahtlose Integration in den zur Verfügung stehenden Platz auf der Produktionsmaschine. Es waren lediglich 500mm in Durchlaufrichtung erforderlich.

Source:

AFBW - Allianz Faserbasierte Werkstoffe Baden-Württemberg e.V.

(c) Fraunhofer UMSICHT
17.12.2020

Fraunhofer: Buch »Prototype Nature« erschienen

Das frisch erschienene Buch »Prototype Nature« stellt die Biologie in den Mittelpunkt und geht der Frage nach, wie diese für die Wissenschaft, Technik, Wirtschaft und Gesellschaft als Vorbild fungieren kann, um neue Wege für eine nachhaltigere Welt zu ebnen. Aufbauend auf dem gleichnamigen Symposium, geben Wissenschaftler*innen und Designer*innen Einblicke in vielversprechende Ansätze der Bionik und der Biotechnologie und damit auch Denkanstöße für das eigene Handeln in einer bioinspirierten Welt.

Ein Blick ins Inhaltsverzeichnis: »Giftfreies Antifouling nach biologischem Vorbild«; »Von Tierhaut zu Bakterienhaut – von Modedesign zu Biodesign«; »Von der Natur lernen – eine Skizze zur Utopie des Sein-Lassens« - so lauten 3 der 31 vorgestellten Ansätze. Das Buch zeigt auf, welche Vielfalt es an Interaktionen zwischen Biologie, Technik und Design gibt und bietet die Möglichkeit, die Funktionsweise heutiger Organismen und Ökosysteme besser zu verstehen, und zeigt wie diese in analoge technische und gestalterische Lösungen überführt werden.

Das frisch erschienene Buch »Prototype Nature« stellt die Biologie in den Mittelpunkt und geht der Frage nach, wie diese für die Wissenschaft, Technik, Wirtschaft und Gesellschaft als Vorbild fungieren kann, um neue Wege für eine nachhaltigere Welt zu ebnen. Aufbauend auf dem gleichnamigen Symposium, geben Wissenschaftler*innen und Designer*innen Einblicke in vielversprechende Ansätze der Bionik und der Biotechnologie und damit auch Denkanstöße für das eigene Handeln in einer bioinspirierten Welt.

Ein Blick ins Inhaltsverzeichnis: »Giftfreies Antifouling nach biologischem Vorbild«; »Von Tierhaut zu Bakterienhaut – von Modedesign zu Biodesign«; »Von der Natur lernen – eine Skizze zur Utopie des Sein-Lassens« - so lauten 3 der 31 vorgestellten Ansätze. Das Buch zeigt auf, welche Vielfalt es an Interaktionen zwischen Biologie, Technik und Design gibt und bietet die Möglichkeit, die Funktionsweise heutiger Organismen und Ökosysteme besser zu verstehen, und zeigt wie diese in analoge technische und gestalterische Lösungen überführt werden.

Das 21. Jahrhundert gilt als das Jahrhundert der Biologie. Biotechnische und bioinspirierte Innovationen verändern heutige Produktionssysteme und unseren Alltag radikal. Gleichzeitig wandelt sich die Biologie selbst wie z. B. die Gentechnik oder die synthetische Biologie zeigen. Die vielfältigen Fortschritte in der Bionik und der Biotechnologie führen zu einem umfassenden Wandel der Mensch-Technik-Biologie-Verhältnisse. »Sie erfordert die Übernahme von Verantwortung in einem Maße, wie es uns Menschen in der Vergangenheit nur selten gelungen ist«, schreibt Mitherausgeber Jürgen Bertling des Fraunhofer UMSICHT in seiner Danksagung.

Interdisziplinäre Zusammenarbeit verschiedener Fachdisziplinen
Ein weiterer wichtiger Aspekt des Buches ist die Interaktion zwischen den verschiedenen Wissenschaften, die sich teilweise ergänzen, aber auch an bestimmten Punkten widersprechen.

Wichtig für die vielfältigen Fortschritte in der Bionik und der Biotechnologie ist die interdisziplinäre Zusammenarbeit verschiedener Fachdisziplinen. Um die Biologie, die Natur als Vorbild für die Wirtschaft und die Gesellschaft zu nutzen, müssen Naturwissenschaftler und Ingenieure mit Fachleuten aus den Industriebereichen Produktion und Marketing, Gestaltung und Design auf offene Art und Weise zusammenarbeiten. »Warum trennt man beispielsweise immer die Funktion von der Schönheit? In der Natur ist Schönheit Funktion. Lasst uns von der Natur lernen«, sagt Mitherausgeberin Anke Bernotat, Design-Professorin an der Folkwang Universität der Künste. So können Lösungen für wettbewerbsfähiges und umweltverträgliches Produzieren und Wirtschaften entwickelt werden.

Herausgeber des Buchs sind Jürgen Bertling vom Fraunhofer UMSICHT und Anke Bernotat (Folkwang Universität der Künste). Das Projekt »Prototype Nature« wurde vom BMBF durch die Projektträgern DLR und BIOKON gefördert.

Source:

Fraunhofer-Institut für Umwelt-, Sicherheits- und Energietechnik UMSICHT

SGL Carbon and Koller Kunststofftechnik manufacture composite windshield for BMW Group (c) Composites United
Skeletal windshield design based on injection molding with carbon fiber profiles
16.11.2020

SGL Carbon and Koller Kunststofftechnik manufacture composite windshield for BMW Group

  • Carbon fibers combined with injection molding replace conventional steel construction
  • SGL Carbon supplies innovative carbon fiber profiles
  • Serial use in a future high-volume model of BMW Group
  • Construction method offers great potential for use in other automotive projects

Already in August, SGL Carbon received a multi-year order from Koller Kunststofftechnik GmbH for the production of novel carbon fiber profiles for serial use in windshields for a future high-volume model of BMW Group.

  • Carbon fibers combined with injection molding replace conventional steel construction
  • SGL Carbon supplies innovative carbon fiber profiles
  • Serial use in a future high-volume model of BMW Group
  • Construction method offers great potential for use in other automotive projects

Already in August, SGL Carbon received a multi-year order from Koller Kunststofftechnik GmbH for the production of novel carbon fiber profiles for serial use in windshields for a future high-volume model of BMW Group.

The profiles are particularly flexible fiber tows, pre-impregnated with thermoplastic resin in various dimensions. They will be compiled by SGL Carbon on the basis of its own 50k carbon fiber at its site in Innkreis, Austria, and subsequently processed by the injection molding experts at Koller to form a skeletal plastic component. The composite component will replace the previous steel-based windshield. Production of the carbon fiber profiles will start in the remainder of 2020 and will then be ramped up gradually over the next few years for the BMW Group model launch.

In the vehicle, the windshield is a connecting element between the roof frames and thus has an important stabilizing function. The carbon fiber profiles add the required stiffness and crash safety to the component. At the same time, they help to significantly reduce the weight of the roof and thus also support the driving dynamics. The injection molding process also enables particularly complex and material-efficient structures. In the BMW Group model, this innovative component concept will cut weight by 40 percent compared to conventional steel designs of the component while creating important space for cable ducts and sensors.

The production of the carbon fiber profiles themselves is also particularly geared to material and process efficiency in large-scale production. The profiles consist of several smaller fiber strands, the so-called rods, and are manufactured using the modern continuous pultrusion process. During product and process development it was one key objective to ensure that material loss during production is almost completely avoided.

"At SGL Carbon, we have been working on the development of thermoplastic carbon fiber profiles for use in injection molding for some time already. This development work is now beginning to pay off. Due to the many advantages and competitive costs, we see a great potential for the technology to be used in other automotive projects too," explains Sebastian Grasser, Head of the Automotive Segment in the Business Unit Composites - Fibers & Materials at SGL Carbon.

"Innovative lightweight construction with hybrid designs has developed into a strategically conclusive concept for Koller Group's OEM customers," confirms Max Koller, CEO of Koller Group. "SGL Carbon's high level of material expertise, combined with the process know-how of KOLLER Kunststofftechnik and KOLLER Formenbau, create the basis for a promising future in innovative lightweight construction technologies. With this order, the BMW Group has confirmed its confidence in the successful cooperation between SGL and Koller; we are particularly pleased about this", said Max Koller.
 
The Koller Group is a globally operating technology company with plants in Europe and China, as well as NAFTA. The Koller Group develops and manufactures lightweight construction, tools and serial components, primarily for the automotive industry.

Source:

SGL CARBON SE

Anlagentechnik zum Carbonfaser-Recycling im Zentrum für Textilen Leichtbau am STFI, Foto: Dirk Hanus.
28.10.2020

Innovationen beim Recycling von Carbonfasern

  • Kohlenstoff mit mehreren Leben

Geht es um die Zukunft der motorisierten Mobilität, reden alle vom Antrieb: Wie viel E-Auto, wie viel Verbrenner verträgt die Umwelt und braucht der Mensch? Zugleich stellen neue Antriebe erhöhte Anforderungen nicht nur an den Motor, sondern auch an dessen Gehäuse und die Karosse: Für solch anspruchsvolle Anwendungen kommen häufig Carbonfasern zum Einsatz. Wie der Antrieb der Zukunft, sollten auch die Werkstoffe am Fahrzeug umweltfreundlich sein. Deshalb ist Recycling von Carbonfasern gefragt. Lösungen dafür haben Institute der Zuse-Gemeinschaft entwickelt.

  • Kohlenstoff mit mehreren Leben

Geht es um die Zukunft der motorisierten Mobilität, reden alle vom Antrieb: Wie viel E-Auto, wie viel Verbrenner verträgt die Umwelt und braucht der Mensch? Zugleich stellen neue Antriebe erhöhte Anforderungen nicht nur an den Motor, sondern auch an dessen Gehäuse und die Karosse: Für solch anspruchsvolle Anwendungen kommen häufig Carbonfasern zum Einsatz. Wie der Antrieb der Zukunft, sollten auch die Werkstoffe am Fahrzeug umweltfreundlich sein. Deshalb ist Recycling von Carbonfasern gefragt. Lösungen dafür haben Institute der Zuse-Gemeinschaft entwickelt.

Carbonfasern, auch als Kohlenstofffasern oder verkürzt als Kohlefasern bekannt, bestehen fast vollständig aus reinem Kohlenstoff. Sehr energieaufwändig wird er bei 1.300 Grad Celsius aus dem Kunststoff Polyacrylnitril gewonnen. Die Vorteile der Carbonfasern: Sie haben kaum Eigengewicht, sind enorm bruchfest und stabil. Solche Eigenschaften benötigt man z.B. am Batteriekasten von E-Mobilen oder in Strukturbauteilen der Karosserie. So arbeitet das Sächsische Textilforschungsinstitut e.V. (STFI) aktuell gemeinsam mit Industriepartnern daran, statisch-mechanische Stärken der Carbonfasern mit Eigenschaften zur Schwingungsdämpfung zu verknüpfen, um die Gehäuse von E-Motoren im Auto zu verbessern. Angedacht ist in dem vom Bundeswirtschaftsministerium geförderten Projekt die Entwicklung sogenannter Hybridvliesstoffe, die neben der Carbonfaser als Verstärkung weitere Faserstoffe enthalten. „Wir wollen, die Vorteile unterschiedlicher Faserstoffe verbinden und so ein optimal auf die Anforderungen abgestimmtes Produkt entwickeln“, erläutert Marcel Hofmann, STFI-Abteilungsleiter Textiler Leichtbau.

Damit würden die Chemnitzer Forschenden bisherige Vliesstoff-Lösungen ergänzen. Sie blicken auf eine 15-jährige Geschichte in der Arbeit mit recycelten Carbonfasern zurück. Der globale Jahresbedarf der hochwertigen Fasern hat sich im vergangenen Jahrzehnt fast vervierfacht, laut Angaben der Industrievereinigung AVK auf zuletzt rd. 142.000 t. „Die steigende Nachfrage hat das Recycling immer stärker in den Fokus gerückt“, betont Hofmann. Carbonfaserabfälle sind ihm zufolge für etwa ein Zehntel bis ein Fünftel des Preises von Primärfasern erhältlich, müssen aber noch aufbereitet werden. Dreh- und Angelpunkt für den Forschungserfolg der recycelten Fasern sind konkurrenzfähige Anwendungen. Die hat das STFI nicht nur am Auto, sondern auch im Sport-Freizeitsektor sowie in der Medizintechnik gefunden, so in Komponenten für Computertomographen. "Während Metalle oder Glasfasern als potenzielle Konkurrenzprodukte Schatten werfen, stört Carbon die Bilddarstellung nicht und kann seine Vorteile voll ausspielen“, erläutert Hofmann.

Papier-Knowhow nutzen
Können recycelte Carbonfasern nochmals den Produktkreislauf durchlaufen, verbessert das ihre CO2-Bilanz deutlich. Zugleich gilt: Je kürzer die Carbonfasern, desto unattraktiver sind sie für die weitere Verwertung. Vor diesem Hintergrund entwickelten das Forschungsinstitut Cetex und die Papiertechnische Stiftung (PTS), beide Mitglieder der Zuse-Gemeinschaft, im Rahmen eines Forschungsvorhabens ein neues Verfahren, das bislang wenig geeignet erscheinende Recycling-Carbonfasern ein zweites Produktleben gibt. „Während klassische Textilverfahren die ohnehin sehr spröden Recycling-Carbonfasern in Faserlängen von mind. 80 mm trocken verarbeiten, beschäftigten wir uns mit einem Verfahren aus der Papierindustrie, welches die Materialien nass verarbeitet. Am Ende des Prozesses erhielten wir, stark vereinfacht gesprochen, eine flächige Matte aus recycelten Carbonfasern und Kunststofffasern“, erläutert Cetex-Projektingenieur Johannes Tietze das Verfahren, mit dem auch 40 mm kurze Carbonfasern zu attraktiven Zwischenprodukten recycelt werden können. Das danach in einem Heißpressprozess entstandene Erzeugnis dient als Grundmaterial für hochbelastbare Strukturbauteile. Zusätzlich wurden die mechanischen Eigenschaften der Halbzeuge durch die Kombination mit endlosfaserverstärkten Tapes verbessert. Das Recyclingprodukt soll, so die Erwartung der Forschenden, glasfaserverstärkten Kunststoffen, Konkurrenz machen, z.B. bei Anwendungen im Schienen- und Fahrzeugbau. Die Ergebnisse fließen nun in weiterführende Forschung und Entwicklung im Kooperationsnetzwerk Ressourcetex ein, einem geförderten Verbund von 18 Partnern aus Industrie und Wissenschaft.

Erfolgreiche Umsetzung in der Autoindustrie
Industriereife Lösungen für die Verwertung von Carbonfaser-Produktionsabfällen werden im Thüringischen Institut für Textil- und Kunststoff-Forschung Rudolstadt (TITK) entwickelt. Mehrere dieser Entwicklungen wurden mit Partnern beim Unternehmen SGL Composites in Wackersdorf industriell umgesetzt. Die Aufbereitung der so genannten trockenen Abfälle, hauptsächlich aus Verschnittresten, erfolgt nach einem eigenen Verfahren. „Dabei führen wir die geöffneten Fasern verschiedenen Prozessen zur Vliesherstellung zu“, sagt die zuständige Abteilungsleiterin im TITK, Dr. Renate Lützkendorf. Neben den Entwicklungen für den Einsatz z.B. im BMW i3 in Dach oder Hintersitzschale wurden im TITK spezielle Vliesstoffe und Verfahren für die Herstellung von Sheet Molding Compounds (SMC) etabliert, das sind duroplastische Werkstoffe, die aus Reaktionsharzen und Verstärkungsfasern bestehen und zum Pressen von Faser-Kunststoff-Verbunden verwendet werden. Eingang fand dies z.B. in einem Bauteil für die C-Säule des 7er BMW. „In seinen Projekten setzt das TITK vor allem auf die Entwicklung leistungsfähigerer Prozesse und kombinierter Verfahren, um den Carbonfaser-Recyclingmaterialien auch von den Kosten her bessere Chancen in Leichtbauanwendungen einzuräumen“, betont Lützkendorf. So liege der Fokus gegenwärtig auf dem Einsatz von CF-Recyclingfasern in thermoplastischen Prozessen zur Platten- und Profilextrusion. „Ziel ist es, die Kombination von Kurz- und Endlosfaserverstärkung in einem einzigen, leistungsfähigen Prozess-Schritt zu realisieren.“

Source:

Deutsche Industrieforschungsgemeinschaft Konrad Zuse e.V.

Carbon reinforced concrete today: thin-walled curved barrel shells as roof elements at ITA (c) ITA. Carbon reinforced concrete today: thin-walled curved barrel shells as roof elements at ITA
05.06.2020

DFG funds Collaborative Research Centre / Transregio 280 on carbon reinforced concrete

  • Joint proposal of TUD and RWTH Aachen University

On 29 May, the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) decided to fund the Collaborative Research Centre (CRC)/Transregio 280 "Carbon reinforced concrete" at Technische Universität Dresden, short TUD, and RWTH Aachen University with the participation of the Institut für Textiltechnik, short ITA, with 12 million euros over the next four years.

The CRC/Transregio 280 “Design Strategies for Material-Minimised Carbon Reinforced Concrete Structures - Principles of a New Approach to Construction” breaks with the traditional way of designing reinforced concrete plants. The interdependence of reinforcement and matrix is being investigated in depth and a completely new design and construction strategy for building with carbon reinforced concrete is being developed.

  • Joint proposal of TUD and RWTH Aachen University

On 29 May, the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) decided to fund the Collaborative Research Centre (CRC)/Transregio 280 "Carbon reinforced concrete" at Technische Universität Dresden, short TUD, and RWTH Aachen University with the participation of the Institut für Textiltechnik, short ITA, with 12 million euros over the next four years.

The CRC/Transregio 280 “Design Strategies for Material-Minimised Carbon Reinforced Concrete Structures - Principles of a New Approach to Construction” breaks with the traditional way of designing reinforced concrete plants. The interdependence of reinforcement and matrix is being investigated in depth and a completely new design and construction strategy for building with carbon reinforced concrete is being developed.

Carbon reinforced concrete enables completely new design and construction possibilities in the building industry. The reasons for this are its very high strength and the possibility of a very low concrete overlay of only a few millimetres, as carbon, unlike structural steel, does not rust. However, the successful use of the new material, which was awarded the German Future Prize in 2016, requires completely new design and production strategies, which are being investigated in the CRC/Transregio.

Up to now, textile reinforcements have been coated and cured prior to component manufacture. This process is called offline consolidation. These stiff semi-finished products are not suitable for the production of complex components based on new, digital and continuous manufacturing processes (including 3D concrete printing and concrete extrusion). Therefore, ITA is investigating in the sub-project B02 of the CRC/Transregio how forming and consolidation steps are shifted in time by prepreg systems into the concreting process and how they can be applied within the new digital continuous manufacturing processes. In addition to established curing mechanisms, such as by heat or UV radiation, new approaches are also being researched. These new approaches include activation via the alkalinity of the concrete, microwaves and induction

The TUD and RWTH Aachen were awarded the grant on the basis of many years of experience in the research field of textile reinforced concrete. The material textile reinforced concrete was developed in two special research areas at both universities from 1999-2011 and was first fundamentally researched.

19 individual institutes are involved in the CRC/Transregio 280. The spokesman of the TUD is Professor Dr Manfred Curbach, the spokesman of the RWTH is Professor Dr Josef Hegger.

Source:

Institut für Textiltechnik der RWTH Aachen University, ITA