From the Sector

Reset
18 results
(c) A. Monforts Textilmaschinen GmbH & Co. KG
05.01.2024

Monforts: New Stenter line installed at Curt Bauer

Monforts' new Montex 8500 stenter line was recently installed at Curt Bauer’s plant in Aue in Germany.

Curt Bauer has been in continuous operation for 150 years, beginning as a weaving mill in Aue in the Ore Mountains region of Saxony back in 1882. Today, with 120 employees, the company has an annual production of 2.2 million metres of fabric and specialises in three key fields – home textiles, special damask fabrics for West African garments and technical textiles.

A first Montex stenter was installed by Monforts at the Aue plant in 2003 and an older machine from a third party supplier was also still in operation prior to the latest upgrade.
“The replacement of our older existing stenter, which was installed in 1985, was long overdue,” explains Gert Bauer. “It had a maximum working width of 2.2 metres and we were looking to both increase productivity and reduce energy requirements.”

Monforts' new Montex 8500 stenter line was recently installed at Curt Bauer’s plant in Aue in Germany.

Curt Bauer has been in continuous operation for 150 years, beginning as a weaving mill in Aue in the Ore Mountains region of Saxony back in 1882. Today, with 120 employees, the company has an annual production of 2.2 million metres of fabric and specialises in three key fields – home textiles, special damask fabrics for West African garments and technical textiles.

A first Montex stenter was installed by Monforts at the Aue plant in 2003 and an older machine from a third party supplier was also still in operation prior to the latest upgrade.
“The replacement of our older existing stenter, which was installed in 1985, was long overdue,” explains Gert Bauer. “It had a maximum working width of 2.2 metres and we were looking to both increase productivity and reduce energy requirements.”

As a consequence, the company opted for a new Montex 8500 line with a working width of 3.2 metres equipped with the MonforClean heat recovery and exhaust air purification system. The Montex stenter remains unmatched in terms of its robustness and long service life and with MonforClean technology, the waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required, compared to full gas and thermal oil heating. Overall energy savings of up to 40% can now be achieved compared to conventional stenters.

The first challenge at the Aue plant was how to fit the significantly larger machine into the available space without restricting the area required for docking operations.

The special multi-level configuration that Monforts designers and Curt Bauer’s team devised in order to meet these requirements involved raising all of the line’s drying zones – with a combined length of over 28 metres – on scaffolding platforms, to enable the ground floor space below them to continue to be fully utilised.

The next challenge involved configuring the MonforClean system without having to make any costly changes to the roofing structure. This, Gert Bauer observes, demanded “millimetre precision”.

With the new line now fully operational, the savings it is providing have yet to be fully calculated.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG

Monforts: Solid Success at ITMA 2023 Photo: Monforts / AWOL Media
07.07.2023

Monforts: Solid Success at ITMA 2023

Finishing machinery specialist Monforts has secured a number of major orders from textile manufacturers in Central and South America recently, and was pleased to welcome a high number of visitors from the region to its stand at ITMA 2023 in Milan from June 8-14.

Among new orders are those for three Montex stenters delivered to the AustralTex Group in Argentina and a further Montex range to denim manufacturer CIT in Brazil. Guatemala’s Global Textiles placed an order for its second Montex stenter, while Mexico’s Zentrix ordered its third and Avante, also in Mexico, has opted for its sixth.

Elsewhere, orders have also been placed for the delivery of three new Montex stenters to one of Pakistan’s major corporations, as well as a new Thermex dyeing range to nonwovens manaufacturer Orsa in Italy. Further orders – both for new machines and retrofit modules – are now anticipated following ITMA 2023, which attracted over 111,000 visitors to Milan.

Finishing machinery specialist Monforts has secured a number of major orders from textile manufacturers in Central and South America recently, and was pleased to welcome a high number of visitors from the region to its stand at ITMA 2023 in Milan from June 8-14.

Among new orders are those for three Montex stenters delivered to the AustralTex Group in Argentina and a further Montex range to denim manufacturer CIT in Brazil. Guatemala’s Global Textiles placed an order for its second Montex stenter, while Mexico’s Zentrix ordered its third and Avante, also in Mexico, has opted for its sixth.

Elsewhere, orders have also been placed for the delivery of three new Montex stenters to one of Pakistan’s major corporations, as well as a new Thermex dyeing range to nonwovens manaufacturer Orsa in Italy. Further orders – both for new machines and retrofit modules – are now anticipated following ITMA 2023, which attracted over 111,000 visitors to Milan.

“Visitor footfall at ITMA 2023 was well beyond the company’s expectations, and we were especially pleased at the constant number of visitors from South American companies, as well as from Asia and Europe,” said Monforts Marketing Manager Nicole Croonenbroek. “We were able to provide them with detailed information about our portfolio of machines and technologies digitally and fielded an unprecedented number of serious enquiries, many of which promise to turn into new business.”

Monforts Montex stenters for processes such as drying, stretching, heat-setting and coating, she added, are already the industry standard for the fabric finishing industry, providing a number of advantages in terms of production throughput and especially in energy efficiency and resource savings. Other key technologies in the Monforts portfolio include relaxation dryers, Thermex dyeing ranges and Monfortex compressive shrinking ranges.

Montex®Coat
“We were also very pleased with the interest in the Montex®Coat, the latest addition to our range of technologies, which we displayed in Milan,” Croonenbroek said.

The Montex®Coat can serve a very diverse number of markets and enables full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments, as well as solvent coatings. Knife coating, roller coating or screen printing can also all be accommodated with this system. It provides the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

Many refinements have been made to the Montex®Coat in the past few years, resulting in higher coating accuracy and the resulting quality of the treated fabrics. A number of advanced new improvements were introduced in Milan, including automatic edge limiters for immediately adapting to new coating widths and a new and simplified hand-held control device. These save considerable time in setting up the machine and ensuring consistent production.

The Montex®Coat unit displayed in Milan was sold to Vietnamese company Thai Tuan during the show.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG

Photo: Montex
15.12.2022

Monforts: 40 years of advanced manufacturing in Austria

Montex Maschinenfabrik – the key site for the manufacturing of Monforts finishing machines in Austria – has celebrated its 40th anniversary in 2022.

Located in St. Stefan, in the centre of Austria’s Lavant Valley in Carinthia, the advanced manufacturing hub was founded by Monforts in 1982.

“From the outset, we have specialised in all aspects of machine production, including high-precision sheet metal working, laser cutting and welding, and the pre-assembly of machines and components, , along with a well-organised quality management and spare parts service,” says Montex plant manager Gert Hanzl.

“We work very closely with the Monforts research and development team in Mönchengladbach, Germany, to take the latest new ideas through testing and prototyping, in readiness for future series production,” Hanzl says. “We are fully exploiting the many new possibilities in the continuous development of design and manufacturing methods. The respective electrical switch cabinets for the machines are delivered just-in-time from Monforts in Germany according to our production schedules.”

Montex Maschinenfabrik – the key site for the manufacturing of Monforts finishing machines in Austria – has celebrated its 40th anniversary in 2022.

Located in St. Stefan, in the centre of Austria’s Lavant Valley in Carinthia, the advanced manufacturing hub was founded by Monforts in 1982.

“From the outset, we have specialised in all aspects of machine production, including high-precision sheet metal working, laser cutting and welding, and the pre-assembly of machines and components, , along with a well-organised quality management and spare parts service,” says Montex plant manager Gert Hanzl.

“We work very closely with the Monforts research and development team in Mönchengladbach, Germany, to take the latest new ideas through testing and prototyping, in readiness for future series production,” Hanzl says. “We are fully exploiting the many new possibilities in the continuous development of design and manufacturing methods. The respective electrical switch cabinets for the machines are delivered just-in-time from Monforts in Germany according to our production schedules.”

While there is standardisation in series-produced Monforts machines, Montex is also increasingly called upon to construct bespoke machines with unique designs, according to the special needs of customers in technical textile or special textiles, he adds.

The core Monforts machine range, including the industry standard Montex stenters, along with relaxation dryers, Thermex dyeing ranges, Monfortex compressive shrinking ranges and Montex®Coat coating units is built at the Austrian site.

Source:

AWOL Media for Montex

(c) Brückner / TEXCOM
from left to right: Ronaldo Huber (MAPEKO), Esteban Scigliano (TEXCOM) and Rodrigo Huber (MAPEKO) in front of one of the two new BRÜCKNER POWER-FRAME stenters
06.12.2022

TEXCOM started up BRÜCKNER POWER-FRAME stenters

TEXCOM has recently started up two new BRÜCKNER POWER-FRAME stenters for knitted fabric with eight compartments and lubrication-free vertical chain and direct gas heating. This is already the 5th BRÜCKNER line purchased by TEXCOM and the successful continuation of the cooperation with BRÜCKNER since 1979. The third member of this successful alliance is the commercial agency, MAPEKO, which has been active for BRÜCKNER for several decades and in the 3rd generation.

With 3 production plants, a commercial office and 6 sales stores distributed around the country, TEXCOM manufactures and distributes knitted fabrics for a highly demanded market, where sports, technical, fashion and workwear fabrics stand out. The company's own developments, such as Twintex, Polisap, Neodry, Sense, Texcom antibacterial, among other brands, are perfect for sports and leisure due to their technical attributes. The company attaches great importance to the fact that all processed materials have the appropriate current environmental certificate (Öko Tex Standard 100, BlueSign and ZDHC)and efficient as well as responsible chemicals are used.

TEXCOM has recently started up two new BRÜCKNER POWER-FRAME stenters for knitted fabric with eight compartments and lubrication-free vertical chain and direct gas heating. This is already the 5th BRÜCKNER line purchased by TEXCOM and the successful continuation of the cooperation with BRÜCKNER since 1979. The third member of this successful alliance is the commercial agency, MAPEKO, which has been active for BRÜCKNER for several decades and in the 3rd generation.

With 3 production plants, a commercial office and 6 sales stores distributed around the country, TEXCOM manufactures and distributes knitted fabrics for a highly demanded market, where sports, technical, fashion and workwear fabrics stand out. The company's own developments, such as Twintex, Polisap, Neodry, Sense, Texcom antibacterial, among other brands, are perfect for sports and leisure due to their technical attributes. The company attaches great importance to the fact that all processed materials have the appropriate current environmental certificate (Öko Tex Standard 100, BlueSign and ZDHC)and efficient as well as responsible chemicals are used.

With more than 100 circular knitting machines and a wide range of possibilities for rotary printing, sublimation, lamination as well as special finishes such as antibacterial or hydrophilic, TEXCOM produces premium sports and leisure wear. This includes the official jersey of Argentina's national soccer team.

More information:
TEXCOM Brückner stenters
Source:

Brückner Trockentechnik GmbH & Co. KG

05.05.2022

Monforts at Techtextil showcasing its finishing and coating technologies

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

The Techtextil and Heimtextil Summer Special exhibitions, taking place together in Frankfurt from June 21-24, represent an opportunity for Monforts to showcase its finishing and coating technologies for two of its major markets – especially at a time when energy prices continue to soar for textile manufacturers in Europe.

Existing customers of Monforts include many manufacturers in the field of home textiles, as well as those making geotextiles, automotive fabrics and other functional materials – all of whom will be well represented in Frankfurt this June. Dedicated Montex lines have also been supplied to producers of airbags, flame retardant barrier fabrics and spacer fabrics, as well as high-temperature filter materials.

Energy prices are rising steeply everywhere and a particular emphasis for Monforts in Frankfurt will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as better insulation of the treatment chambers or the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air resulting in a radical reduction in the conventional heat supply required compared to gas and thermal oil heating. The modular system for heat recovery can also be extended for exhaust air cleaning and odour elimination. Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation including modification of the heating source.

With the Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

All of these very different materials require coating and finishing for maximum efficiency, using Monforts technologies which provide the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

The Monforts EcoApplicator offers further potential for sustainably achieving perfect finishes via a precise direct application system, as an alternative to conventional padding – where fabrics are immersed in a bath of the required finishing chemicals. It can significantly further reduce the energy and water required and finishes can be applied on just one side of the fabric, or both, and even separately on each side, to be sealed in place via different heating zones in the stenter.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) A. Monforts Textilmaschinen GmbH & Co. KG
07.04.2022

Montex stenter at ITM

Monforts and its Turkish representative Neotek are looking forward to the forthcoming ITM 22 international textile machinery show taking place from June 14-18 at the Tüyap Fair and Congress Centre in Istanbul, after a three-year break.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying. The resulting constant evaporation rate within the stenter ensures optimum energy utilisation and also avoids markings on the fabric.

With the latest Montex stenters, overall energy savings of up to 40% can now be achieved compared to a conventional stenter with no heat recovery or energy optimisation measures like high-quality chamber insulation.

Monforts and its Turkish representative Neotek are looking forward to the forthcoming ITM 22 international textile machinery show taking place from June 14-18 at the Tüyap Fair and Congress Centre in Istanbul, after a three-year break.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying. The resulting constant evaporation rate within the stenter ensures optimum energy utilisation and also avoids markings on the fabric.

With the latest Montex stenters, overall energy savings of up to 40% can now be achieved compared to a conventional stenter with no heat recovery or energy optimisation measures like high-quality chamber insulation.

The Montex stenter also benefits from full digital control, with the Qualitex 800 PLC control system providing ease of operation and rapid access to line and management data, including full operating cost overviews, as well as maintenance monitoring.

Advances in digital technology mean that there are also now significant gains to be made in the retrofitting of existing Monforts machines with the latest automatic drives and control systems, going far beyond the basic replacement of spare parts.

“We will be emphasising the robustness and versatility of the Montex stenter for essential processes such as drying, stretching, heatsetting and coating at the Istanbul show,” said Monforts Area Sales Manager Thomas Päffgen.

“With energy prices rising steeply everywhere, features such as the MonforClean system, or the EcoBooster, in which waste heat from the drying process is used to pre-heat the drying air, are proving more invaluable than ever,” added Ahmet Kilic of Neotek. “Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation.”

Source:

A. Monforts Textilmaschinen GmbH & Co. KG

31.03.2022

Monforts at Techtextil North America

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Advanced machine operation
With the highly intuitive Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Versatility is the key
Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

Source:

AWOl Media / A. Monforts Textilmaschinen GmbH & Co. KG

(c) Monforts / AWOL Media
07.02.2022

Monforts: Turkish upholstery leader opts for the Montex®Coat

Turkish powerhouse in home textiles and furnishing fabrics Altun Tekstil has just commissioned the first Montex®Coat coating system in Turkey.

The advanced machine has been installed at the ever-expanding family-owned company’s industrial complex in Bursa and is being employed to provide an anti-slip and textured backing to upholstery fabrics with a stable and uniform foam, via knife-over-roller coating.  

Founded in 1993, Altun exports its fabrics to more than 60 countries, with its major export markets being Russia and Ukraine, as well as many Middle Eastern and European countries.
Its integrated operations include the production of texturized yarns, weaving and raschel knitting, in addition to dyeing and finishing. With a major focus on tulle curtains and upholstery, the company’s fabric range also extends to a wide variety of apparel styles.

Turkish powerhouse in home textiles and furnishing fabrics Altun Tekstil has just commissioned the first Montex®Coat coating system in Turkey.

The advanced machine has been installed at the ever-expanding family-owned company’s industrial complex in Bursa and is being employed to provide an anti-slip and textured backing to upholstery fabrics with a stable and uniform foam, via knife-over-roller coating.  

Founded in 1993, Altun exports its fabrics to more than 60 countries, with its major export markets being Russia and Ukraine, as well as many Middle Eastern and European countries.
Its integrated operations include the production of texturized yarns, weaving and raschel knitting, in addition to dyeing and finishing. With a major focus on tulle curtains and upholstery, the company’s fabric range also extends to a wide variety of apparel styles.

Altun has installed eight stenters in various widths at its two plants since 2016 – coincidentally the year Monforts Turkish representative Neotek was founded. All of the stenters are engineered for specific product lines and the Montex®Coat unit is integrated into the latest of these lines, which has a maximum working width of 2.2 metres and eight chambers.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

14.10.2021

Monforts: Automated finishing at Knopf’s Sohn

Knopf’s Sohn, a contract finisher of technical textiles, has installed a fully automated Montex stenter at its plant in Helmbrechts, Germany.
Knopf’s Sohn is processing technical textiles for the automotive, aerospace, home furnishings and workwear markets, based on wool, cellulose, polyamide and polyester fabrics, along with elastane blends, in weights of 80-800gsm.

The Montex machinery range is constantly being upgraded to meet evolving customer needs for greater automation, ease of operation and energy optimisation. The latest ten chamber line at Knopf’s Sohn, with a working width of up to 2.0 metres, was engineered to specific requirements in order to accelerate the company’s move to fully automatic control of its production, and high scaffolding was required for its installation.

The line benefits from two integrated ECO Booster modules to provide high energy savings. These compact, air-to-air heat exchangers, installed within the roof structure of the line, exploit energy from the exhaust gas to preheat up to 60% of the incoming fresh air entering the stenter.

Knopf’s Sohn, a contract finisher of technical textiles, has installed a fully automated Montex stenter at its plant in Helmbrechts, Germany.
Knopf’s Sohn is processing technical textiles for the automotive, aerospace, home furnishings and workwear markets, based on wool, cellulose, polyamide and polyester fabrics, along with elastane blends, in weights of 80-800gsm.

The Montex machinery range is constantly being upgraded to meet evolving customer needs for greater automation, ease of operation and energy optimisation. The latest ten chamber line at Knopf’s Sohn, with a working width of up to 2.0 metres, was engineered to specific requirements in order to accelerate the company’s move to fully automatic control of its production, and high scaffolding was required for its installation.

The line benefits from two integrated ECO Booster modules to provide high energy savings. These compact, air-to-air heat exchangers, installed within the roof structure of the line, exploit energy from the exhaust gas to preheat up to 60% of the incoming fresh air entering the stenter.

The use of a single ECO Booster unit has been calculated to save up to 35% in energy costs, based on fixation processes. Fully automatic operation, set at the Monforts Qualitex control unit, ensures there is no additional burden on the machine operator.

The line is powered by Exxotherm indirect heating, which practically eliminates the yellowing which can be experienced during the treatment of certain polyamide and elastane-based fabrics, and is also equipped with a Conticlean circulating air filter system for constant high drying capacity.

Software
The latest Qualitex visualisation software offers operators reliability and easy control with its full HD multi-touch monitor and slider function, dashboard function with individual adaptation to operating states and faster access to comprehensive recipe data management.

With the Monformatic control system, the exact maintenance of the dwell time in combined treatment processes (drying and heat-setting) can be monitored. When the heat-setting point is reached, the fan speed is automatically adjusted, keeping energy consumption fully under control.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) Brückner Trockentechnik GmbH & Co. KG
23.09.2021

WEIDMANN and BRÜCKNER: New standards in stenter technology

WEIDMANN GmbH in Süßen is known worldwide as a specialist for the finishing of fiber and down-proof articles and woven industrial fabrics. Customers particularly appreciate the company's reliability and flexibility with regard to their individu-al requirements, and consistently high quality of its products. The Swabian textile manufacturer finishes premium fabrics, mainly for the bedding industry, using the latest technology and in an environmentally conscious manner.

WEIDMANN GmbH in Süßen is known worldwide as a specialist for the finishing of fiber and down-proof articles and woven industrial fabrics. Customers particularly appreciate the company's reliability and flexibility with regard to their individu-al requirements, and consistently high quality of its products. The Swabian textile manufacturer finishes premium fabrics, mainly for the bedding industry, using the latest technology and in an environmentally conscious manner.

The complex production and finishing processes for high-quality fabrics require a reliable and efficient machine technology. With this in mind, WEIDMANN has always relied on the proven stenter technolo-gy from BRÜCKNER. For many decades, the German textile machinery manufacturer has been a world leader in the con-struction of production lines for the finishing of classical textiles, woven industrial  fabrics, nonwovens, glass fabrics and floor coverings. In addition to stenters, the company's production program also in-cludes coating lines, relaxation dryers, sanfor lines, continuous dyeing lines as well as ovens for the bonding of nonwovens and other special lines. All machines are produced 100% in-house in Germany.

Both companies continuously invest in new and innovative technology in order to be successful and competitive today and in the future. Only Recently, a completely newly developed BRÜCKNER stenter was installed in the ultra-modern plant at WEIDMANN. During the intensive project engineering phase it soon became clear which features are of special importance for their daily production requirements:

  • uniform moisture distribution in the machine entry and during pick-up of the specialized   chemicals in the finishing padder before the thermoprocess
  • weft-straight fabric flow with minimized residual distortion
  • very good accessibility for maintenance and daily cleaning
  • sensor technology and automation of setting parameters for energy optimization
  • heat-recovery with hot water generation for the dye house
  • the line must be fully Industry 4.0 capable
Source:

Brückner Trockentechnik GmbH & Co. KG

(c) Brückner Trockentechnik GmbH & Co. KG
12.08.2021

BRÜCKNER successful in Turkey with stenters

The Turkish company ARIKAN Mensucat Industry and Trade Inc. was founded in 1993 and is located in Kahramanmaraş, one of the southernmost cities of the country. Today, the family-owned company employs around 1,500 people and finishes around 55 tons of knitwear every day. In addition to many well-known Turkish fashion manufacturers, ARIKAN also supplies international manufacturers in Europe, Russia, the Gulf States and other leading international markets.

The Turkish company ARIKAN Mensucat Industry and Trade Inc. was founded in 1993 and is located in Kahramanmaraş, one of the southernmost cities of the country. Today, the family-owned company employs around 1,500 people and finishes around 55 tons of knitwear every day. In addition to many well-known Turkish fashion manufacturers, ARIKAN also supplies international manufacturers in Europe, Russia, the Gulf States and other leading international markets.

The German machinery manufacturer BRÜCKNER supported the Turkish company from the very beginning. From the foundation of the dyeing and finishing plant, BRÜCKNER supplied three stenters for the finishing of the high-quality knitted fabric in 2014. Two more lines followed in 2016. For decades, BRÜCKNER has been the market leader for the finishing of knitted fabric. Especially for very fine and elastic fabric, special line configurations and technological know-how are necessary to be able to produce a high-quality end product. During the drying and heat-setting process, for example, extremely accurate and uniform temperature distribution over the entire length and width of the dryer is essential. In the BRÜCKNER stenter this is achieved, among other things, by the alternating arrangement of the thermal zones every 1.5 meters and by the proven split-flow air system.

The machine operators at ARIKAN appreciate the easy control of BRÜCKNER lines. The visualization is intuitively designed and offers many auxiliary systems for an optimized production process. In addition, significant energy savings can be achieved with just a few changes to the machine parameters.

The management at ARIKAN attaches great importance to energy saving, especially in the fabric finishing department. The drying process is one of the most energy-intensive in the entire process chain, therefore the biggest savings can be made here. These have a direct impact on the manufacturing costs of the textiles and thus on competitiveness in the market. In the meantime, talks are already in progress for another BRÜCKNER line which will include a very special feature: a combined heating system for the dryer. For many customers - and so also for ARIKAN in Turkey - e.g. steam energy is available free or very cheap. With the combined heating system developed by BRÜCKNER it is possible to use this steam energy for heating up the dryer and thus to achieve significant savings. If the available steam is not sufficient for a running process, it is automatically switched over to gas heating. This mode of operation does not only have an effect on the energy costs, but also makes a considerable contribution to environmental protection.

Monforts (c) Monforts
19.11.2020

İlay puts a premium on energy with new Monforts installation

The company, founded in 1993, has established a reputation for leadership in new printing techniques and technologies with customers across Europe, as well as with many of the leading Turkish brands.

Mission
On its mission to achieving continuous progress in error-free and resource-efficient manufacturing, İlay has just taken delivery of a new Monforts Montex stenter range, with a working width of two metres and eight TwinAir chambers.

“This installation provides us with much improved control options for all process parameters and compared to the old stenter it is replacing, we are particularly impressed with the energy savings we are making,” Mr Savaş says.

Achieving energy savings on Montex stenters has been a key focus for Monforts designers and engineers in Germany for many years.

The company, founded in 1993, has established a reputation for leadership in new printing techniques and technologies with customers across Europe, as well as with many of the leading Turkish brands.

Mission
On its mission to achieving continuous progress in error-free and resource-efficient manufacturing, İlay has just taken delivery of a new Monforts Montex stenter range, with a working width of two metres and eight TwinAir chambers.

“This installation provides us with much improved control options for all process parameters and compared to the old stenter it is replacing, we are particularly impressed with the energy savings we are making,” Mr Savaş says.

Achieving energy savings on Montex stenters has been a key focus for Monforts designers and engineers in Germany for many years.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying.

The resulting constant evaporation rate within the stenter ensures optimum energy utilisation. In addition, TwinAir chambers feature special panelling for low heat radiation, careful sealing of all connecting positions and chamber access points, and air locks at both the entry and the exit.

“Monforts stenters set the benchmark in terms of energy efficiency and help conserve resources,” says Ahmet Kılıç, founder of Neotek, the representative for Monforts in Turkey. “Automatically setting the initial moisture content requirement for a specific process before drying to a minimum value helps reduce heat evaporation and consequently, energy consumption. The hermetic sealing of the stenter frame further prevents the loss of heated air as well as the ingress of excessive cold air – which has to be heated back up if it is not kept out in the first place.”

The new Montex line was completed at İlay Textile in August 2020, with no problems during either installation or commissioning.

 

Source:

AWOL Media

Monforts texCoat coating system (c) Monforts / AWOL Media
06.10.2020

Monforts at Innovate Textile & Apparel (ITA) 2020

During the Innovate Textile & Apparel (ITA) virtual textile machinery show which will run from October 15th-30th 2020, Monforts will be emphasising its leadership position in three key fields – advanced coating, denim finishing and fabric sanforizing.

With its multi-head capability, the latest Monforts texCoat coating system provides flexibility with an unprecedented range of options and a wide range of modules available.

Refinements
“Since we acquired the coating technology that our systems are based on we have made a lot of refinements and all of them are reflected in higher coating accuracy and the resulting quality of the treated fabrics,” says Monforts Head of Technical Textiles, Jürgen Hanel.
“Our systems have the shortest fabric path from the coating unit into the stenter and we have all variations of coating application systems too – and all of these options are available in wider widths, with the engineering and manufacturing from a single source here in Europe.”

During the Innovate Textile & Apparel (ITA) virtual textile machinery show which will run from October 15th-30th 2020, Monforts will be emphasising its leadership position in three key fields – advanced coating, denim finishing and fabric sanforizing.

With its multi-head capability, the latest Monforts texCoat coating system provides flexibility with an unprecedented range of options and a wide range of modules available.

Refinements
“Since we acquired the coating technology that our systems are based on we have made a lot of refinements and all of them are reflected in higher coating accuracy and the resulting quality of the treated fabrics,” says Monforts Head of Technical Textiles, Jürgen Hanel.
“Our systems have the shortest fabric path from the coating unit into the stenter and we have all variations of coating application systems too – and all of these options are available in wider widths, with the engineering and manufacturing from a single source here in Europe.”

CYD
Denim finishing is meanwhile a field in which Monforts has an undisputed lead and it has been working closely with its many partners in the key denim manufacturing countries of Bangladesh, Brazil, China, India, Mexico Pakistan and Turkey to develop advanced solutions. The latest of these is the CYD yarn dyeing system.
“CYD is based on the proven Econtrol® dyeing system for fabrics*,” explains Monforts Head of Denim Hans Wroblowski. “It integrates new functions and processes into the weaving preparatory processes – spinning, direct beaming, warping and assembly beaming, followed by sizing and dyeing – in order to increase quality, flexibility, economic viability and productivity. The CYD system has been developed in response to a very strong market demand.”

Pre-shrinking
Monforts has also recently delivered a significant number of its latest Monfortex sanforizing lines to customers around the world.
Sanforizing is vital to final fabric quality, pre-shrinking it by compressing prior to washing, to limit any residual or further shrinkage in a made-up finished garment to less than 1%, for perfect comfort and fit over an extended lifetime.

As with industry-leading Montex stenters, Monfortex lines benefit from the latest Qualitex 800 control system which allows all parameters to be easily automated via the 24-inch colour touchscreen, including production speed, control of all fabric feed devices, rotation spray or steaming cylinder options, the width of the stretching field and the rubber belt pressure. Up to 10,000 separate process parameter records can be generated and stored by the data manager.

 

*Econtrol® is a registered mark of DyStar Colours Distribution GmbH, Germany.

Acafintex looks to a bright future with new Monforts technology (c) AWOL Media
Acafintex father and son ownership team Don Francisco and Lic Francisco Moyano at the new Monforts installation.
14.09.2020

Acafintex looks to a bright future with new Monforts technology

At a total length of over 71 metres, the Montex finishing line that has just been installed by Monforts for Acafintex at its plant in Puebla, Mexico, is one of the highest capacity stenters the German technology leader has delivered to date.

Puebla is known as the epicentre of Mexico’s textile and clothing industry and is ideally placed for supplying both the USA and Europe, being three hours from the Gulf of Mexico for shipping via the Atlantic, and five hours from the Pacific coast as well.

Mexico's textile and clothing industry spans the entire production chain – from cotton growing and man-made fibre production to the manufacture of yarn, fabric, finished clothing and accessories. The industry is estimated to directly employ around 640,000 workers and to provide livelihoods for many more people indirectly. The country is a key supplier of textiles and clothing to the USA, but has faced fierce competition from China, which has until recently been the largest supplier of textiles and clothing to the US market.

At a total length of over 71 metres, the Montex finishing line that has just been installed by Monforts for Acafintex at its plant in Puebla, Mexico, is one of the highest capacity stenters the German technology leader has delivered to date.

Puebla is known as the epicentre of Mexico’s textile and clothing industry and is ideally placed for supplying both the USA and Europe, being three hours from the Gulf of Mexico for shipping via the Atlantic, and five hours from the Pacific coast as well.

Mexico's textile and clothing industry spans the entire production chain – from cotton growing and man-made fibre production to the manufacture of yarn, fabric, finished clothing and accessories. The industry is estimated to directly employ around 640,000 workers and to provide livelihoods for many more people indirectly. The country is a key supplier of textiles and clothing to the USA, but has faced fierce competition from China, which has until recently been the largest supplier of textiles and clothing to the US market.

However, the position of Mexico in the US import market has become more stable following the signing of the United States-Mexico-Canada Agreement (USMCA), which came into force in July this year. The country has also been a key beneficiary of the current trade war that is raging between China and the USA.

In addition, there is scope for higher sales in Mexico’s domestic market. The country has a population of 129 million people who are becoming increasingly prosperous, with a large proportion of younger people who are spending more on clothing.

Flexible operation

Founded in 1986, family-owned Acafintex operates as a commission dyehouse, finishing both knitted and woven fabrics for local companies in Mexico, in widths of between 100cm to 3.6 metres. The company is run by father and son team Don Francisco and Lic Francisco Moyano.

“We have very flexible operations for fabric finishing and also produce and sell our own fabrics for both the fashion industry and for the uniforms market,” says Don Francisco. “These days, we are increasingly finishing materials for technical textiles and for the automotive industry too. We have both local and international suppliers of both yarns and base fabrics and make sure we choose the best and most reliable sources. Exports now account for over 40% of our sales.”

European contract

With a  width of 3.8 metres, the new Monforts Montex line at Acafintex is equipped with no less than 12 double TwinAir drying chambers to meet the requirements of specific technical textiles to a European customer, in a contract secured following the company’s ISO 9001 certification in 2019. The line is equipped with an integrated heat recovery system and also benefits from an exhaust air cleaning system to ensure the most resource-efficient processing available on the market.

On the Monforts TwinAir system, the airflows above and below the fabric being dried can be regulated completely independently of each other, with Optiscan Auto-Balance fully controlling the distance between the fabric and the dryer nozzles via variable-frequency fan motors and CCD chip evaluation. As a result, the evaporation rate of the stenter and its energy utilisation are always fully optimised. Contact-free drying eliminates the possibility of fabric marking or stitch draft.

Highly-intuitive Monforts Qualitex visualisation software allows all machine functions and process parameters to be assessed and controlled easily, and thousands of article specific settings and formulations to be called up at any time – with 100% reproducible results.

In combination with an existing Montex stenter, the new line has expanded finishing capacity at Acafintex to an annual 20 million linear metres.

Modifications

“From the installation to the start-up, we were supported by a team of Monforts technicians and local representative Arnulf Thaler at Sattex here in Mexico,” says Lic Francisco. “Of course, every installation has its challenges and with such big machines we needed to modify several things inside the factory and also required certain modifications from Monforts which were all carried out successfully.”  

Forced, like much of the textile industry globally, to temporarily suspend operations at the height of the Covid-19 pandemic, Acafintex is now back to full production, having installed the necessary safety measures for its employees, and is anticipating a bright future.

“We are passionate about developing new materials in search of mutual benefit for both our clients and suppliers, as well as our own workforce and the environment,” Don Francisco Moyano concludes. “Investment in the latest technology like this new Monforts line plays a key role in helping us achieve our long-term goals.”

Sustainable leadership for GtA with new Monforts Montex wide width lines (c) AWOL Media
GtA Managing Director Andreas Niess
27.07.2020

Sustainable leadership for GtA with new Monforts Montex wide width lines

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

A new standard in pure white, 100% clean and fault-free textile substrates has been demanded by this market in recent years due to the rapid growth in digitally-printed banners and billboards – often referred to as ‘soft signage’.

The substrates of choice for digital printing are 100% polyester warp knits which are resilient and allow excellent take-up of inks, and vibrant colours and clear and precise images to be achieved with digital printing techniques. The knitted construction also has the advantage of elasticity, which is a plus in terms of flexibility for installers.

Critically, the warp knitted fabrics have extremely smooth surfaces which is becoming increasingly important due to the general move away from PVC coatings which were the standard in the past.

It was to finish these fabrics for Georg and Otto Friedrich GmbH as well as providing such services for many other customers, that the GtA plant in Neresheim, Baden-Württemberg, was established in 2015.

The purpose-built plant on a greenfield site was initially equipped with a fully-automated, 72 metre long Monforts installation comprising a washing machine integrated with a 3.6 metre wide, seven-chamber Montex stenter. The line quickly went from single to double shift production and then to 24/7 operation  to meet demand.

Expanded widths

Building on the success of this installation, GtA has now installed two more Montex stenter lines – both in expanded working widths of 5.6 metres and purpose-built at Montex GmbH in Austria.

A six-chamber Montex unit is combined with a washing machine to guarantee the purity of the substrates, while a five-chamber line is integrated with a wide-width coating machine. This new coating capability at GtA has led to a number of new additions to the Georg and Otto Friedrich DecoTex range for digital printing, including wide width fabrics with flame retardant, antimicrobial and non-slip finishes.

The new Montex stenter lines benefit from all of the latest innovations from Monforts, including the Smart Sensor system for the optimised maintenance planning of key mechanical wear components on the stenters. A comprehensive overview of the condition of all parts at any time is now available for operators within the highly intuitive Qualitex visualization software.

With Qualitex, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

Environmental commitment

GtA is run by a seasoned team of textile professionals led by Managing Director Andreas Niess.

“We have received excellent service from Monforts from the outset and we were happy to place the order for these two new lines as part of our ongoing cooperation,” he says. “With all of the latest Monforts advances in technology we are fully in control of all production and quality parameters with these lines, as part of our significant commitment to innovative environmental technology.”

The GtA plant, which operates in near-cleanroom conditions, has also been equipped with proprietary technology to fully exploit the Monforts air-to-air heat recovery systems that are now standard with Montex stenters.

“Around 30 per cent of our investment volume at the site goes to energy-saving measures and we are sure that this commitment is worthwhile,” Mr Niess says. “As an example, our integrated heat recovery system fully exploits the waste heat from the process exhaust air and the burner exhaust gases of the Monforts stenters, allowing us to achieve an exhaust air temperature of  between 30 to 34°C, compared to what would conventionally be between 140 to 160°C. Another focus has been on exhaust air purification technology and here too, the latest technology has been installed with integrated heat recovery elements.”

This, he adds, saves 52% of the energy that would normally be used – equating to 5,800,000 KwH per year. The necessary audits for energy-efficient companies are also carried out annually.

In addition, GtA has purpose-designed the automatic chemical mixing and dosing systems that feed the padders for the key treatments that are carried out on the fabrics through the stenters.

The company is going further, however, in its pursuit of clean production and raw materials.

"We want to be an asset and not a burden on our immediate environment and therefore do not use any additives containing solvents," Mr Niess says. “We were the first to use fully halogen-free flame retardant chemistry, and we use bio-based, finely ground alumina products for the washing process instead of surfactants. PES polyester yarns made from recycled material are also increasingly used and the latest additions to our raw materials portfolio, the RC-Ocean products, are made from recycled sea plastic.

“We are now planning a combined heat and power plant for the production of electrical energy and heat and we will also build a photovoltaic system that converts solar radiation into electrical energy. GtA wants to be the first textile finishing company to be CO2-neutral in the manufacture of all of its products by 2025. The complete heat supply and heating for the 13,000 square metre production hall, as well as the office building and the hot water supply for the domestic water, is already energy-neutral. We are convinced that this commitment will pay off in the long term and our positive business development proves that sustainability and business profitability are perfectly compatible.”

In addition to the products for Georg and Otto Friedrich GmbH, GtA  offers its manufacturing capacities for other customers as a contract service.

All products are manufactured in accordance with Öko-Tex Standard 100, product class 1 and the company is also involved in the research and development of new sustainable manufacturing processes, in cooperation with many regional universities and funding project partners.

Source:

AWOL Media for A. Monforts Textilmaschinen GmbH & Co. KG

Monforts denim mills move hemp into the mainstream © Cone Denim
Cone Denim Sweet Leaf jeans.
30.06.2020

Monforts denim mills move hemp into the mainstream

  • There is an urban legend that hemp canvas was used to make the very first pair of Levi’s jeans.
  • While this is a myth that originated in the counterculture of the 1960s, hemp is without doubt the fibre of the moment for the denim industry.

At the second Kingpins24 virtual denim show that was broadcast from New York on June 23rd and 24th, the sustainable benefits of hemp fibre were referenced by many Monforts customers who are now including it in their collections, including AGI Denim, Artistic Milliners, Black Peony, Calik, Cone Denim, Naveena Denim Mills (NDM) and Orta.

“Hemp is an easy to grow fibre which requires no irrigation, no fertilizers, no herbicides and no chemicals,” says Allan Little, Director of Product Development for Cone Denim, which has recently launched its Sweet Leaf collection featuring the fibre. “Significantly, it also uses fifty per cent or even less water than cotton in cultivation.”

It can also bring some new aesthetics to denim too, he adds.

  • There is an urban legend that hemp canvas was used to make the very first pair of Levi’s jeans.
  • While this is a myth that originated in the counterculture of the 1960s, hemp is without doubt the fibre of the moment for the denim industry.

At the second Kingpins24 virtual denim show that was broadcast from New York on June 23rd and 24th, the sustainable benefits of hemp fibre were referenced by many Monforts customers who are now including it in their collections, including AGI Denim, Artistic Milliners, Black Peony, Calik, Cone Denim, Naveena Denim Mills (NDM) and Orta.

“Hemp is an easy to grow fibre which requires no irrigation, no fertilizers, no herbicides and no chemicals,” says Allan Little, Director of Product Development for Cone Denim, which has recently launched its Sweet Leaf collection featuring the fibre. “Significantly, it also uses fifty per cent or even less water than cotton in cultivation.”

It can also bring some new aesthetics to denim too, he adds.

“Hemp has a unique colour and adds a different cast to our indigo, the drape and texture of the fabrics is different and it even adds  a bit of a unique hand, so combined with its sustainable credentials we are proud to be bringing the Sweet Leaf collection to the market.”

US supply chain

Cone is currently sourcing its hemp from France, but with much of its manufacturing now in Mexico – and with the introduction of the US Farm Bill in 2018 which has legalised the growing of legal hemp – is exploring the possibility of investing in the US supply chain.

“With US hemp we’re really at the R&D phase,” Little emphasises. “It’s a unique crop, so coming up with the right stalk to provide the right fibre is challenging. We’ve experimented with different types of seed and various methods of decortication.”

Decortication, he explains, is the mechanical removal of the outside layer of the hemp stalk to useable fibre on the inside. A second process, cottonization, is necessary to make the fibre suitable for spinning, because compared to cotton, hemp is longer, stiffer, and less flexible.

100% success

At the end of 2019, Naveena (NDM), headquartered in Karachi, introduced fabrics featuring up to 51% hemp content in blends with Tencel and recycled polyester and this year has developed the first 100% hemp denims.

“The response to the fabrics we showed last year was incredible and we were looking forward to the response to this latest development – which everyone was asking for – at the Kingpins show in Amsterdam, which unfortunately was unable to go ahead,” says NDM’s Director of Marketing Rashid Iqbal. “We produced initial samples in an undyed state because we were not sure how the wet spun yarn would react in the dyeing, but I’m happy to say we have had success in this respect and are now able to provide one hundred per cent indigo dyed hemp denim.”

Environmental benefits

“Differentiation is the key in the highly-competitive denim industry and we have assisted our customers with trials and optimised processing parameters for a range of different fibres, including hemp, both at our Advanced Technology Centre in Germany and at their own mills around the world,” says Hans Wroblowski, Monforts Head of Denim. “Given the environmental benefits of hemp, and the liberalisation of its cultivation in many parts of the world, the interest in it now comes as no surprise. We have the technologies and know-how to help our customers to fully maximise their hemp denims at all post-weaving stages of production.”

Monforts has a dominant position in the field of denim finishing with its well proven Montex stenters. It has been enjoying further recent success with its Eco Line concept based on two key technology advances – the Eco Applicator and the Thermo Stretch.

The latest Monforts innovation for denim is the CYD yarn dyeing system. This technology is based on the effective and established dyeing process for denim fabrics that is now being applied for yarn dyeing.

The CYD system also integrates new functions and processes into the weaving preparation processes – spinning, direct beaming, warping and assembly beaming, followed by sizing and dyeing – to increase quality, flexibility, economic viability and productivity. A full CYD line is now available for trials at the company’s Advanced Technology Centre.

Monforts at Techtextil India (c) Monforts
A recent Monforts texCoat installation.
20.11.2019

Monforts at Techtextil India

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

Monforts Textilmaschinen GmbH & Co. KG will be providing information on its extensive range of coating and finishing technologies for the production of nonwovens and technical textiles at the forthcoming Techtextil India exhibition.

“India is already a very important market for Monforts and there are exciting prospects ahead for Indian manufacturers of technical textiles, who are well positioned to capitalise on growth opportunities,” says Monforts Head of Denim Hans Wroblowski, who will be at the Monforts stand in Hall 4, booth C52 at the show. “India has one of the largest working-age populations in the world and a complete textile value chain for both natural and synthetic fibres.”

In addition, he adds, India’s government, through its Ministry of Textiles, has been actively promoting the growth of technical textiles through various programmes based on investment promotion, subsidies, the creation of infrastructure and the stimulation of consumption.

As a result, India’s Ministry of Textiles is forecasting that the growth of technical textiles in the country will be over 18% annually in the next few years, from a value of US$16.6 billion in 2018 to US$28.7 billion in 2021.

Value addition

High value-added technical products such as wide-width digital printing substrates, carbon fabrics for high-performance composites, filter media, flame retardant barrier fabrics and heavy-duty membranes are now being coated on Monforts texCoat ranges and finished with the company’s industry-leading Montex stenters.

“Since we acquired the technology that our coating units are based on in 2015, we have made a lot of refinements,” says Hans. “All of these developments are reflected in higher coating accuracy and the resulting quality of the treated fabrics. At the same time, our latest multi-functional coating heads offer an unprecedented range of options, with a wide range of modules available.”

The texCoat user interface is now equipped with the unique Monforts visualisation system and the magnetic doctor blade has greater power reserves. Options include a carbon fibre-reinforced composite coating drum with a more scratch-resistant surface and maximum rigidity and remote control which simplifies exact adjustment for the operator.

Montex stenters in special executions are meanwhile ideal for the drying and finishing of both technical woven fabrics and nonwovens and characterised by high stretching devices in both length and width.

“The European-built Montex range of stenters has earned its leading position in the technical textiles market due to the overall robustness, reliability and economy of these machines,” Hans concludes. “Whatever the intended end-product – and we continue to discover potentially new areas in which technical textiles can be utilised all the time – we have the machine specification and know-how to turn ideas into reality. In India we also benefit from the strong sales and service support of A.T.E. Enterprises.”

Texchtextil India takes place alongside World of Composites at the Bombay Exhibition Centre in Mumbai from November 20-22.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG by AWOL Media.

(c) A. Monforts Textilmaschinen GmbH & Co. KG
12.07.2019

Further benefits and savings with the new Monforts MonforClean

A. Monforts Textilmaschinen GmbH & Co. KG presented an energy-optimised new version of its industry-leading Montex stenter for the first time at ITMA 2019 in Barcelona from June 20-26th.

With the introduction of the new MonforClean exhaust air treatment system and other unique process innovations, Monforts has been able to further reduce the energy consumption of Montex stenters by a further 13%.

Exhaust air treatment on stenter frames has posed particular challenges over the years, since the air can contain significant amounts of oil, fibre and even wax particles that may see emissions limits being reached in the processing of certain fabrics, depending on the legal specifications.

In addressing this issue, Monforts is now incorporating the MonforClean module into the stenter frame, so there is no additional space requirement. At the same time, the costs for laborious secondary installations and the piping of the exhaust air treatment components, as well as supporting structures are eliminated due to the machine configuration.

A. Monforts Textilmaschinen GmbH & Co. KG presented an energy-optimised new version of its industry-leading Montex stenter for the first time at ITMA 2019 in Barcelona from June 20-26th.

With the introduction of the new MonforClean exhaust air treatment system and other unique process innovations, Monforts has been able to further reduce the energy consumption of Montex stenters by a further 13%.

Exhaust air treatment on stenter frames has posed particular challenges over the years, since the air can contain significant amounts of oil, fibre and even wax particles that may see emissions limits being reached in the processing of certain fabrics, depending on the legal specifications.

In addressing this issue, Monforts is now incorporating the MonforClean module into the stenter frame, so there is no additional space requirement. At the same time, the costs for laborious secondary installations and the piping of the exhaust air treatment components, as well as supporting structures are eliminated due to the machine configuration.