From the Sector

Reset
78 results
DITF: CO2-negative construction with new composite material Photo: DITF
Structure of the wall element
20.03.2024

DITF: CO2-negative construction with new composite material

The DITF is leading the joint project "DACCUS-Pre*". The basic idea of the project is to develop a new building material that stores carbon in the long term and removes more CO2 from the atmosphere than is emitted during its production.       

In collaboration with the company TechnoCarbon Technologies, the project is now well advanced - a first demonstrator in the form of a house wall element has been realized. It consists of three materials: Natural stone, carbon fibers and biochar. Each component contributes in a different way to the negative CO2 balance of the material:

Two slabs of natural stone form the exposed walls of the wall element. The mechanical processing of the material, i.e. sawing in stone cutting machines, produces significant quantities of stone dust. This is very reactive due to its large specific surface area. Silicate weathering of the rock dust permanently binds a large amount of CO2 from the atmosphere.

The DITF is leading the joint project "DACCUS-Pre*". The basic idea of the project is to develop a new building material that stores carbon in the long term and removes more CO2 from the atmosphere than is emitted during its production.       

In collaboration with the company TechnoCarbon Technologies, the project is now well advanced - a first demonstrator in the form of a house wall element has been realized. It consists of three materials: Natural stone, carbon fibers and biochar. Each component contributes in a different way to the negative CO2 balance of the material:

Two slabs of natural stone form the exposed walls of the wall element. The mechanical processing of the material, i.e. sawing in stone cutting machines, produces significant quantities of stone dust. This is very reactive due to its large specific surface area. Silicate weathering of the rock dust permanently binds a large amount of CO2 from the atmosphere.

Carbon fibers in the form of technical fabrics reinforce the side walls of the wall elements. They absorb tensile forces and are intended to stabilize the building material in the same way as reinforcing steel in concrete. The carbon fibers used are bio-based, produced from biomass. Lignin-based carbon fibers, which have long been technically optimized at DITF Denkendorf, are particularly suitable for this application: They are inexpensive due to low raw material costs and have a high carbon yield. In addition, unlike reinforcing steel, they are not susceptible to oxidation and therefore last much longer. Although carbon fibers are more energy-intensive to produce than steel, as used in reinforced concrete, only a small amount is needed for use in building materials. As a result, the energy and CO2 balance is much better than for reinforced concrete. By using solar heat and biomass to produce the carbon fibers and the weathering of the stone dust, the CO2 balance of the new building material is actually negative, making it possible to construct CO2-negative buildings.

The third component of the new building material is biochar. This is used as a filler between the two rock slabs. The char acts as an effective insulating material. It is also a permanent source of CO2 storage, which plays a significant role in the CO2 balance of the entire wall element.

From a technical point of view, the already realized demonstrator, a wall element for structural engineering, is well developed. The natural stone used is a gabbro from India, which has a high-quality appearance and is suitable for high loads. This has been proven in load tests.  Bio-based carbon fibers serve as the top layer of the stone slabs. The biochar from Convoris GmbH is characterized by particularly good thermal insulation values.

The CO2 balance of a house wall made of the new material has been calculated and compared with that of conventional reinforced concrete. This results in a difference in the CO2 balance of 157 CO2 equivalents per square meter of house wall. A significant saving!

* (Methods for removing atmospheric carbon dioxide (Carbon Dioxide Removal) by Direct Air Carbon Capture, Utilization and Sustainable Storage after Use (DACCUS).

Source:

Deutsche Institute für Textil- und Faserforschung

26.02.2024

SGL Carbon: Review of options for Business Unit Carbon Fibers

SGL Carbon SE is currently evaluating various strategic options for the Business Unit Carbon Fibers (CF). These include a possible partial or complete divestment of the Business Unit. In a first step, potential interested parties shall be approached with the general data of the Business Unit to determine their interest in an acquisition. If there is sufficient interest, a structured transaction process will be carried out in a second step. Overall, a share of sales amounting to around € 179.6 million after nine months in 2023 (9M 2022: € 269.0 million) is therefore under review. The CF sales share corresponded to 21.9% of SGL Carbon's consolidated sales after nine months in 2023 (9M 2022: 31.5%). Adjusted EBITDA of the Business Unit excluding the result from joint ventures amounted to minus € 10,9 million after nine months in 2023 (9M 2022: € 27,9 million). Despite the operating loss of CF after nine months in 2023, SGL Carbon maintains its guidance for fiscal year 2023. This shows the positive development of the three other business units and the resilience of SGL Carbon's business model.

SGL Carbon SE is currently evaluating various strategic options for the Business Unit Carbon Fibers (CF). These include a possible partial or complete divestment of the Business Unit. In a first step, potential interested parties shall be approached with the general data of the Business Unit to determine their interest in an acquisition. If there is sufficient interest, a structured transaction process will be carried out in a second step. Overall, a share of sales amounting to around € 179.6 million after nine months in 2023 (9M 2022: € 269.0 million) is therefore under review. The CF sales share corresponded to 21.9% of SGL Carbon's consolidated sales after nine months in 2023 (9M 2022: 31.5%). Adjusted EBITDA of the Business Unit excluding the result from joint ventures amounted to minus € 10,9 million after nine months in 2023 (9M 2022: € 27,9 million). Despite the operating loss of CF after nine months in 2023, SGL Carbon maintains its guidance for fiscal year 2023. This shows the positive development of the three other business units and the resilience of SGL Carbon's business model.

Carbon Fibers manufactures textile, acrylic and carbon fibers as well as composite materials at seven locations in Europe and North America. Following the temporary drop in demand for carbon fibers from the important wind industry market, the Business Unit's sales and earnings fell significantly in the course of fiscal year 2023. Due to the importance of the wind industry for the European Green Deal, SGL Carbon and many experts assumed that the wind industry recovers quickly. Unfortunately, this is currently not the case. Even if demand picks up, the company assumes that Carbon Fibers will need additional resources to remain competitive in the international market environment and to exploit market opportunities in the best possible way. Against this background, SGL Carbon is reviewing all possibilities to support a positive further development of the Carbon Fibers Business Unit.

More information:
SGL Carbon carbon fibers
Source:

SGL Carbon SE 

Gerhard Lettl (AVK Board Member, C.F. Maier Europlast GmbH & Co. KG), Felix Pohlmeyer (ITA), Prof. Dr Jens Ridzewski (AVK Board Member, IMA Materialforschung und Anwendungstechnik GmbH), Tim Röding (ITA), from left to right © AVK
Gerhard Lettl (AVK Board Member, C.F. Maier Europlast GmbH & Co. KG), Felix Pohlmeyer (ITA), Prof. Dr Jens Ridzewski (AVK Board Member, IMA Materialforschung und Anwendungstechnik GmbH), Tim Röding (ITA), from left to right
23.11.2023

CarboScreen: Sensor monitoring for complex carbon fibre production

Felix Pohlkemper and Tim Röding from Institut für Textiltechnik (ITA) of RWTH Aachen University are developing a technology with their start-up CarboScreen GmbH that makes complex carbon fibre production controllable through sensor monitoring. With the help of CarboScreen technology, it should be possible to double the production speed from the current 15 m/min to 30 m/min in the medium term. The doubling of production speed alone could result in an increase in turnover of up to €37.5 million per year and production plant. Felix Pohlkemper and Tim Röding were awarded third place in the AVK Innovation Award 2023 in the Processes and Procedures category for this ground-breaking development. The award ceremony took place during the JEC Roof Forum in Salzburg, Austria.

Felix Pohlkemper and Tim Röding from Institut für Textiltechnik (ITA) of RWTH Aachen University are developing a technology with their start-up CarboScreen GmbH that makes complex carbon fibre production controllable through sensor monitoring. With the help of CarboScreen technology, it should be possible to double the production speed from the current 15 m/min to 30 m/min in the medium term. The doubling of production speed alone could result in an increase in turnover of up to €37.5 million per year and production plant. Felix Pohlkemper and Tim Röding were awarded third place in the AVK Innovation Award 2023 in the Processes and Procedures category for this ground-breaking development. The award ceremony took place during the JEC Roof Forum in Salzburg, Austria.

The production of carbon fibres is highly complex. In the current state of the art, however, the manufacturing process is only monitored manually by semi-skilled workers. However, even minimal fibre damage during production leads to a reduction in the quality of the carbon fibre. In extreme cases, it can also lead to plant fires. To ensure production quality, the production speed is currently limited to a maximum of 15 m/min. In fact, the production speed of the systems could be higher. The sensor-based online monitoring of Carbo-Screen makes it possible to increase the production speed to 30 m/min in the medium term. As a result of the increased production volume per system, the specific production costs of the carbon fibre are reduced, which can result in lower prices.

A reduced sales price would make it possible to use carbon fibres and their composite materials even more widely in traditional markets such as aerospace technology and wind energy, as well as for mass production in the automotive industry.

The CarboScreen online monitoring system is currently being developed for industrial use. It is to be validated at an industrial plant in 2024. CarboScreen GmbH was founded as part of EXIST funding and offers AI-supported sensor systems for carbon fibre production. The sensor technology continuously monitors the fibre throughout the entire production process. Deviations are detected automatically.

The winners of the AVK Innovation Award are honoured annually by the AVK Industrievereinigung Verstärkte Kunststoffe. Companies, institutes and their partners are honoured in three categories: products and applications, processes and procedures, and research and science.

08.11.2023

Hexcel showcases new fiber HexPly® M79 Prepregs at METSTRADE 2023

Hexcel will continue to celebrate its 75th anniversary and highlight its latest developments for the Marine market at METSTRADE 2023 on November 15-17. Hexcel will showcase innovative advanced lightweight material technologies including new intermediate and high modulus fiber HexPly® M79 prepregs and present example high-performance superyacht and windship components developed by customers using Hexcel materials.

The new intermediate modulus prepreg combines the low temperature curing and simple processing of the DNV GL accredited HexPly M79 resin system with the market-leading stiffness of HexTow® IM2C fiber, creating a uniquely optimized composite material for highly loaded components. Originally developed to provide best-in-class performance for America’s Cup and IMOCA hull and deck structures, the new combination minimizes structural deformation under load in parts such as rigs, foils, and other appendages.

Hexcel will continue to celebrate its 75th anniversary and highlight its latest developments for the Marine market at METSTRADE 2023 on November 15-17. Hexcel will showcase innovative advanced lightweight material technologies including new intermediate and high modulus fiber HexPly® M79 prepregs and present example high-performance superyacht and windship components developed by customers using Hexcel materials.

The new intermediate modulus prepreg combines the low temperature curing and simple processing of the DNV GL accredited HexPly M79 resin system with the market-leading stiffness of HexTow® IM2C fiber, creating a uniquely optimized composite material for highly loaded components. Originally developed to provide best-in-class performance for America’s Cup and IMOCA hull and deck structures, the new combination minimizes structural deformation under load in parts such as rigs, foils, and other appendages.

For a high modulus solution, HexTow® HM54 fiber is also now available with the HexPly M79 resin system. The unique mechanical properties of HexTow HM54 fiber allow structural designers to achieve higher safety margins for both stiffness and strength critical applications. Both products can be manufactured with Hexcel G-Vent technology for out-of-autoclave processing, delivering a reduction in process time and cost without compromising mechanical performance.

Hexcel will also display customer products that have benefited from the performance and processing gains provided by HexPly materials. A section of a Solid Sail mast made using Bureau Veritas (BV)-approved HexPly® M9.6 prepregs will be exhibited at METS. Such masts are used for wind propulsion and, by harnessing the power of ocean winds, they reduce reliance on engines, reducing fuel usage and emissions.

Visitors to the Hexcel booth will also see a section of a radar arch part from luxury motor yacht builder Sunseeker made using HexPly® XF surfacing technology and HexPly® SuperFIT semi-pregs. The part is lighter in weight and stiffer than versions made using resin-infusion processes and de-molds with a pinhole-free surface that needs minimal preparation to be ready for painting. Sunseeker has recorded an overall reduction in process time and material costs of around 30% against traditional prepreg parts, using Hexcel composite materials.

Source:

Hexcel

05.10.2023

EURATEX and CIE warn EU Presidency about de-industrialised Europe

Ahead of the extra-ordinary Council on 6 October in Granada, EURATEX President, Alberto Paccanelli, and CIE President, Jose Vte Serna, call on the EU Presidency to develop a new competitiveness strategy, which can relaunch the European industry and ensure it will remain competitive in the decades to come. This means bringing together trade, energy, state aid and sustainability policies into a single, integrated, comprehensive approach, which can support a robust and modern European manufacturing industry.  
 
To consolidate a strong industrial structure in Europe, the Union should

Ahead of the extra-ordinary Council on 6 October in Granada, EURATEX President, Alberto Paccanelli, and CIE President, Jose Vte Serna, call on the EU Presidency to develop a new competitiveness strategy, which can relaunch the European industry and ensure it will remain competitive in the decades to come. This means bringing together trade, energy, state aid and sustainability policies into a single, integrated, comprehensive approach, which can support a robust and modern European manufacturing industry.  
 
To consolidate a strong industrial structure in Europe, the Union should

  1. secure the supply of clean energy at a competitive cost;
  2. support innovation and foster the necessary talent pool and
  3. be more assertive in achieving an international level-playing field on sustainability, based on the European model.  

During the past few years the implementation of incoherent and conflicting objectives under the trade, energy, industrial and sustainability policy has been observed. As a matter of fact, while the circular economy promised to be a recipe for a competitive industry of the future, the likelihood of pushing the EU industry out of the market and driving investment elsewhere than in Europe is very high. If this approach were to continue in the next years, it will result in a de-industrialised Europe, depending on imports from abroad. Such a Europe would be more exposed to geopolitical turmoil, with no agency to deliver its vision of peace, well-being and a healthy environment to its citizens.

It is fundamental for Europe to pursue a more coherent set of policies that put the competitiveness of its domestic industry at the core. In this context, all the industrial manufacturing sectors should be in the scope, including the textile industry, given its importance in providing essential products and applications to our society. A first impactful action that can be taken in this direction, would be to expand the scope of the Net-Zero Industry Act (NZIA) to include the textiles and clothing industry.
 
The history of European industry is fully woven in the birth and expansion of the European textiles industry since the XVIII century. Still today, the European textiles and clothing industry holds a pivotal position in the market, encompassing a diverse range of sectors and applications. In terms of employment, our industry creates 1,3 million direct jobs in Europe, encompassing a wide range of roles, from design and production to distribution and retail. European textiles have a wide range of applications, the most common one is of course clothing and fashion. The industry has a long history of producing high-quality apparel, with various regions specializing in specific niches.
 
Beyond clothing, there is a wide range of industrial sectors were textiles play an essential role, including  Automotive (used for upholstery, interior components, and even lightweight composite materials), Aircraft and Shipbuilding (where textiles are employed for their lightweight and high-strength properties, to enhance fuel efficiency, reduce emissions, and improve overall performance), Building and Construction (insulation, roofing, geotextiles, and architectural textiles), or Personal Protective Equipment, for medical personnel, firefighters, police and army officers. This includes masks, gowns, uniforms, helmets, and fire-resistant clothing, ensuring safety in hazardous environments.
 
Textiles are essential components of our society and our well-being. It is key for Europe to maintain its capacity to manufacture high-quality, sustainable and high-technology textiles.  With this in mind, the competitiveness policy of the future and the related funds to support it, should include the textile ecosystem in its scope.  

 

More information:
Euratex EU council Policy Hub
Source:

Euratex

25.09.2023

ARC Research Hub to support sustainable manufacturing of fibre materials

In August 2023, Australian Research Council (ARC) Chief Research Officer Professor Christina Twomey officially launched the ARC Research Hub for Functional and Sustainable Fibres.

Through collaboration with 16 domestic and international Partner Organisations, the team at the ARC Research Hub will be conducting research across three core themes – Sustainability, Circular Economies, and Extraordinary Functionality.

Led by Deakin University, the ARC Research Hub aims to harness Australia’s research capacity in fibre, textiles, and composite materials to develop materials with enhanced functionality, meeting Australian consumer and industrial demand for advanced fibre capabilities including recycling and re-purposing textile waste.
 
Professor Twomey said that the ARC Research Hub is fundamental to increasing collaboration between Australia’s most innovative researchers and vital industries.

In August 2023, Australian Research Council (ARC) Chief Research Officer Professor Christina Twomey officially launched the ARC Research Hub for Functional and Sustainable Fibres.

Through collaboration with 16 domestic and international Partner Organisations, the team at the ARC Research Hub will be conducting research across three core themes – Sustainability, Circular Economies, and Extraordinary Functionality.

Led by Deakin University, the ARC Research Hub aims to harness Australia’s research capacity in fibre, textiles, and composite materials to develop materials with enhanced functionality, meeting Australian consumer and industrial demand for advanced fibre capabilities including recycling and re-purposing textile waste.
 
Professor Twomey said that the ARC Research Hub is fundamental to increasing collaboration between Australia’s most innovative researchers and vital industries.

“The ARC has a proud history of supporting outstanding research that benefits the Australian community, and the ARC Research Hub for Functional and Sustainable Fibres is a great example of this,” Professor Twomey said.
 
“In collaboration with industry partners, the research team are building on the work undertaken by the ARC Research Hub for a World-class Future Fibre Industry which ended in 2021 – this continued success is no easy feat.

“This new ARC Research Hub will strengthen productivity and competitiveness of the advanced manufacturing sector and will place Australia at the forefront of a global shift towards functional and sustainable materials.”
 
The ARC is investing $5 million over 5 years under the ARC Industrial Transformation Research Program.

It is expected that the ARC Research Hub will address the immediate need to reduce industry’s reliance on petroleum-derived materials and to reduce the environmental impact of supply chains.

Source:

Australian Research Council

Toray Composite Materials America: Boeing Supplier of the Year Photo Toray
04.09.2023

Toray Composite Materials America: Boeing Supplier of the Year

Toray Composite Materials America, Inc. headquartered in Tacoma, Washington, has been awarded the "Boeing Supplier of the Year" award, a leadership-nominated award given to supplier companies that support and propel Boeing's strategic objectives through risk-sharing and enduring partnerships. This year, 12 companies were selected from among 11,000 Boeing suppliers worldwide, and CMA was selected as one of them for the Alliance Award. This is Toray's second award from Boeing, receiving the Supplier of the Year Excellence Award in 2019.

Toray began supplying Boeing in 1975 when it first qualified TORAYCA™ T300 carbon fiber for commercial application on the Boeing 737. Since then, Toray has provided high-performance carbon fiber and highly toughened, primary structure carbon fiber composite prepreg on various programs.

The trophy was presented by William A. Ampofo II, Vice President of Parts & Distribution Services and Supply Chain for Boeing Global Services and Chair of the Supply Chain Operations Council to CMA.

Toray Composite Materials America, Inc. headquartered in Tacoma, Washington, has been awarded the "Boeing Supplier of the Year" award, a leadership-nominated award given to supplier companies that support and propel Boeing's strategic objectives through risk-sharing and enduring partnerships. This year, 12 companies were selected from among 11,000 Boeing suppliers worldwide, and CMA was selected as one of them for the Alliance Award. This is Toray's second award from Boeing, receiving the Supplier of the Year Excellence Award in 2019.

Toray began supplying Boeing in 1975 when it first qualified TORAYCA™ T300 carbon fiber for commercial application on the Boeing 737. Since then, Toray has provided high-performance carbon fiber and highly toughened, primary structure carbon fiber composite prepreg on various programs.

The trophy was presented by William A. Ampofo II, Vice President of Parts & Distribution Services and Supply Chain for Boeing Global Services and Chair of the Supply Chain Operations Council to CMA.

Source:

Toray

28.06.2023

EPTA highlights contribution of pultruded composites to sustainable construction

Increasing energy and resource efficiency in the construction sector will be key to the EU’s ambition of achieving climate neutrality by 2050. By enabling the manufacture of strong, durable and lightweight products, composite materials can help the construction sector improve its environmental sustainability, as well as reduce total lifecycle costs. The latest EPTA industry briefing, Pultruded composites contribute to a more sustainable future for construction, discusses how pultruded composites answer the need for materials offering high performance, faster installation, corrosion resistance and low maintenance.

The report is available to download from the EPTA website.

Increasing energy and resource efficiency in the construction sector will be key to the EU’s ambition of achieving climate neutrality by 2050. By enabling the manufacture of strong, durable and lightweight products, composite materials can help the construction sector improve its environmental sustainability, as well as reduce total lifecycle costs. The latest EPTA industry briefing, Pultruded composites contribute to a more sustainable future for construction, discusses how pultruded composites answer the need for materials offering high performance, faster installation, corrosion resistance and low maintenance.

The report is available to download from the EPTA website.

The future of construction
As one of the largest global users of energy and raw materials, the construction industry is under immense pressure to improve its sustainability. At the same time, it must respond to demands for improved performance and reduced total cost of ownership. New materials will be needed to minimise the use of natural resources, enable a reduction of carbon footprint and facilitate circular economy practices. Choosing the optimum materials required for durability throughout the lifecycle will be increasingly important. A shift to off-site production is also forecast, where factory-controlled environments and automated processes can improve quality control, lower waste, and reduce work on site.

Lightweight pultruded parts can be pre-assembled into modules or complete structures in the factory for faster installation on site. Lightweight profiles lower energy use during transportation and installation, and a longer service life combined with minimal maintenance can deliver a reduced through-life carbon footprint. Pultruded parts such as profiles, gratings, beams, tubes and planks are increasingly found in a range of building, construction and infrastructure applications. Examples include bridge decks, fencing, stairs and handrails, train platforms, cladding, utility poles, modular building concepts, and window frames.

One application offering large growth potential for composites is bridges. Composite bridges are being designed to provide a service life of 100 years and unlike steel bridges do not require regular repainting to protect them from corrosion. Over recent years, pultruded glass fibre composite has become a highly popular choice for pedestrian and cycle bridges. Pre-fabricated ‘easy fit’ bridge decking planks, pre-assembled bridge modules and complete bridge ‘kits’ are now available. Corrosion-resistant composite bridges are ideal for use near water or on the coast, and in remote locations where regular maintenance operations would be difficult. A composite bridge can deliver the same performance as a steel structure with a weight saving of up to 50% or more. This enables more streamlined bridge designs which require less substantial supporting structures and foundations, greatly reducing consumption of materials and energy. Lightweight also results in easier logistics and simplified installation. Pultruded are more easily transported to the construction site, with lower fuel consumption, and easier to move on site, often reducing labour requirements and the capacity of lifting equipment.

A lifecycle approach
As the construction industry looks to the future, the environmental and economic benefits of composite materials linked to easier logistics and installation, durability and low maintenance are becoming increasingly valued. More projects are demonstrating the benefits of composite materials and standards covering the design, fabrication and installation of pultruded profiles are making it easier for the construction industry to use them. With ongoing development and collaboration, pultrusion has the potential to contribute to a more sustainable future for construction and many other industries. EPTA will continue to promote the advancement of pultrusion technology and its applications and foster sustainable practices within the industry.

Source:

The European Pultrusion Technology Association (EPTA)

(c) Freudenberg Performance Materials Holding SE & Co. KG
13.02.2023

Freudenberg Performance Materials presents range of solutions for the composites industry at JEC 2023

Freudenberg Performance Materials (Freudenberg) will present surfacing veils and core materials for lightweight fiber reinforced plastic (FRP) parts at JEC in Paris, France. Freudenberg will also be showcasing Enka® Solutions flow media and spacers for efficient vacuum infusion, resin transfer and foam injection molding processes for applications in the composites industry, etc. at the international composites show.
 
Freudenberg’s solutions for the FRP industry include a variety of glass, PAN and PET nonwovens, as well as core materials for the production of lightweight fiber reinforced plastic parts. These products are designed for anti-corrosion coatings in piping and tank construction, smooth UV resistant surfaces for facade panels, and other applications for a diverse range of end products. Products made from fiber reinforced plastics must be equipped with surfacing veils to provide abrasion resistance, corrosion resistance, smooth surfaces and mechanical strength. Freudenberg offers high-tech nonwovens that can meet these challenges.
 

Freudenberg Performance Materials (Freudenberg) will present surfacing veils and core materials for lightweight fiber reinforced plastic (FRP) parts at JEC in Paris, France. Freudenberg will also be showcasing Enka® Solutions flow media and spacers for efficient vacuum infusion, resin transfer and foam injection molding processes for applications in the composites industry, etc. at the international composites show.
 
Freudenberg’s solutions for the FRP industry include a variety of glass, PAN and PET nonwovens, as well as core materials for the production of lightweight fiber reinforced plastic parts. These products are designed for anti-corrosion coatings in piping and tank construction, smooth UV resistant surfaces for facade panels, and other applications for a diverse range of end products. Products made from fiber reinforced plastics must be equipped with surfacing veils to provide abrasion resistance, corrosion resistance, smooth surfaces and mechanical strength. Freudenberg offers high-tech nonwovens that can meet these challenges.
 
Enka® Solutions products are characterized by their typical 3D entangled polymeric filament structures. Thanks to this structure, they are exceptionally suitable as flow media and spacers when producing composite materials.

Source:

Freudenberg Performance Materials Holding SE & Co. KG

30.12.2022

Composites United declares membership in Composites Germany

Society and the economy are facing existential challenges. In addition to the consequences of climate change, these include the realisation that energy and many resources are no longer available in the usual quantities, so that their efficiency must be significantly increased in the short term. Lightweight construction, especially with fibre composite materials, can and will make an important contribution here, e.g. in wind power plants or hydrogen storage systems. As an umbrella organisation, Composites Germany represents the capabilities and interests of the German fibre composite industry. With the re-entry of Composites United, Composites Germany will combine the forces of the two leading composites networks in Germany and its position will be significantly strengthened. Changed framework conditions make the re-entry possible and necessary.

Society and the economy are facing existential challenges. In addition to the consequences of climate change, these include the realisation that energy and many resources are no longer available in the usual quantities, so that their efficiency must be significantly increased in the short term. Lightweight construction, especially with fibre composite materials, can and will make an important contribution here, e.g. in wind power plants or hydrogen storage systems. As an umbrella organisation, Composites Germany represents the capabilities and interests of the German fibre composite industry. With the re-entry of Composites United, Composites Germany will combine the forces of the two leading composites networks in Germany and its position will be significantly strengthened. Changed framework conditions make the re-entry possible and necessary.

VDMA and Leichtbau BW will continue to support the work of Composites Germany as associate members and contribute the know-how of their members. Together, the organisations will promote sustainable lightweight construction as a key technology for Germany, focusing on composites materials, says Prof. Klaus Drechsler of Composites United, one of the two board members of Composites Germany. As a network and mouthpiece of the composites industry, Composites Germany bundles the interests of its members. The aim is to continuously expand activities, promote innovations and technologies, develop new markets and new value chains, and anchor training and further education, adds his board colleague Dr Michael Effing of AVK. The agreement was concluded on 29 November 2022 during the JEC Forum DACH in Augsburg, where both associations were cooperation partners of the event.

Source:

Composites Germany

31.10.2022

Cinte Techtextil China announces exhibitors for December Edition

From 7 – 9 December 2022, Cinte Techtextil China will welcome visitors sourcing solutions for 12 application areas of technical textiles and nonwovens at the National Exhibition and Convention Center in Shanghai.

A number of countries and regions are represented at the fair’s International Zone, with companies from Austria, Belgium, France, Germany, Hong Kong, Italy, the Netherlands, Spain, Sweden, Switzerland, Taiwan, and the US. Standout international exhibitors include:

From 7 – 9 December 2022, Cinte Techtextil China will welcome visitors sourcing solutions for 12 application areas of technical textiles and nonwovens at the National Exhibition and Convention Center in Shanghai.

A number of countries and regions are represented at the fair’s International Zone, with companies from Austria, Belgium, France, Germany, Hong Kong, Italy, the Netherlands, Spain, Sweden, Switzerland, Taiwan, and the US. Standout international exhibitors include:

  • TESTEX, an international, independent Swiss institute which specialises in the testing and certification of textile and leather products. The organisation is a founding member and official representative of the OEKO-TEX® Association, and will present their certification services at the fairground.
  • Cotton Council International (CCI) is a non-profit trade association that promotes US cotton fibre and manufactured cotton products, with their COTTON USA™ Mark. At this year’s fair they will showcase cotton spunlace fabric, wipes, kitchen tissues, facial masks, cosmetic removers, and more, with their products particularly applicable to Agrotech, Clothtech, Medtech, and Sporttech.
  • Graf + Cie AG is a subsidiary of the Rieter Group, and a leading supplier of clothing for carding and combs for combing machines in the short- and long-staple spinning industry. This year, the Swiss company will showcase stationary flats, and metallic card clothing for roller cards.
  • At the returning German Pavilion, buyers can source sought-after technical textiles and nonwovens that are renowned for their quality. The companies and expertise on display at this pavilion are endorsed by the Federal Republic of Germany, with several exhibitors highlighted below:
  • Brückner Textile Technologies GmbH & Co KG has developed machinery for the textile industry since 1949. Today, the company offers complete line systems for the dry finishing of both woven and knitted fabric, as well as for technical textiles, glass fibres, and floor coverings.
  • Perlon (Zhejiang) Co Ltd is part of a global group of companies that specialises in the manufacture of synthetic filaments, with factories in China, Germany, Poland, and the US. Their products have a diverse range of potential uses, largely categorised in the Agrotech and Indutech application areas.
  • IBENA Textilwerke GmbH produces various functional fabrics for Protech. At the fair, the company will be showcasing insulative, flame retardant (FR) textiles for firefighting and search & rescue services. Developed with DuPont™ aramid material, their FR properties will not diminish after washing or repeated use.

This year’s fair also sees the return of the Taiwan Zone. With support from the Taiwan Nonwoven Fabrics Industry Association, the area will showcase a range of industry leading nonwoven products and services, by brands such as KNH Enterprise, Nan Liu Enterprise, Unique Pretty Ind, and Web-Pro Corporation.

As a world’s largest manufacturer of technical textiles, China is home to a vast array of companies responsible for innovative products. Some domestic exhibitors to look out for are:

  • CTA Hi-Textiles Co Ltd, a high-tech enterprise controlled by China Textile Science Research Institute. In recent years, the company has developed several new textile composite materials, and their products are widely used in sectors such as national defence, policing and public security, medical protection, and engineering and manufacturing.
  • Sateri is one of the world’s largest producers of viscose fibre, with an annual capacity of 1.8 million metric tonnes. At their mills, they make yarn and fibre products applicable to sectors such as beauty, hygiene and personal care, medical, wipes, and protective wear.

To help international buyers stay connected with the Chinese market, Match Plus, the fair’s online business matching platform, will support foreign buyers achieve their sourcing goals despite travel limitations. Further information on Match Plus will be available at a later stage.

The fair’s product categories cover 12 application areas, which comprehensively span a full range of potential uses in modern technical textiles and nonwovens. These categories also cover the entire industry, from upstream technology and raw materials providers to finished fabrics, chemicals and other solutions.

27.10.2022

The curtain lifts on JEC World 2023

Well-known as the “Festival of composites” each year in Paris, JEC World is the event dedicated to composite materials, their manufacturing technologies and application markets. It will take place in Paris Nord Villepinte from April 25th to 27th, 2023, giving once again the opportunity for professionals to meet with the worldwide composites industry.

Six months prior to the show, the program of the 2023 edition starts to unveil.

For 2023, JEC World is preparing a wide program of conferences and expert panels discussions focusing largely on sustainability and key challenges of our industry and application sectors. In aerospace, construction, ground transportation, health, design, energy (…): sustainable initiatives and greener mindsets are taking over the latest developments in high-performance composite technologies and applications.

Well-known as the “Festival of composites” each year in Paris, JEC World is the event dedicated to composite materials, their manufacturing technologies and application markets. It will take place in Paris Nord Villepinte from April 25th to 27th, 2023, giving once again the opportunity for professionals to meet with the worldwide composites industry.

Six months prior to the show, the program of the 2023 edition starts to unveil.

For 2023, JEC World is preparing a wide program of conferences and expert panels discussions focusing largely on sustainability and key challenges of our industry and application sectors. In aerospace, construction, ground transportation, health, design, energy (…): sustainable initiatives and greener mindsets are taking over the latest developments in high-performance composite technologies and applications.

The JEC Composites Innovation Awards
For 25 years, through the JEC Composites Innovation Awards, JEC Group has rewarded cutting-edge, creative projects which demonstrate the full potential of composite materials. Highly recognised worldwide, they offer the winners and their partners international recognition, a greater exposure during the JEC World show and throughout the following year, new business opportunities as well as an enhanced customer trust.
All companies, R&D centres and their partners can apply before December 16th, and the winners will be revealed during the ceremony, on March 2nd in Paris.

The JEC Composites Startup Booster, the leading startup competition in the world of composites and advanced materials comes back for a sixth edition. All entrepreneurs, SMEs, startups and academic spinoffs building innovative composites projects who want to get international visibility and grow their business with key players of the composites industry & OEMs are already signing up.

Following the call for entries (deadline January 15th, 2023), 20 startups will be selected by JEC Group and its partners Airbus and Mercedes-Benz. Out of the 20 finalists, 3 winners will be selected during the pitching sessions of the show: one in the “Materials & Products” category, one in the “Process, Manufacturing & Equipment” category and a special “Sustainability” award.

More information:
JEC World Composites Startup Award
Source:

JEC Group

(c) JEC Group
13.10.2022

JEC Forum DACH reveals the Startup Booster Finalists

JEC Forum DACH‘s primary goal is to promote the DACH region’s dynamic composites ecosystem. Besides an extensive program of business meetings and conferences, innovation will have a special place in Augsburg from November 29 to 30, 2022 as attendees will have the opportunity to witness the JEC Composites Startup Booster and the AVK Awards. Winners of both competitions will be announced during a dedicated ceremony on November 29th.

The five finalists are:

BioWerkz: Closing the Loops
At BioWerkz a new bio-based, resource-efficient, and CO2-negative material called “NEWood” is developed,  using only wood waste and agricultural waste bound using fungal mycelium; the root network of mushrooms as a natural binder without the need for any synthetic binders.

Bufo Technology – HARDCORK: High-Performance Biobased Composite – Superior by nature
Bufo Technology has developed the high-performance composite material HARDCORK® made from cork, fibers and a thermosetting matrix. HARDCORK® can be manufactured as a core material, sandwich panel or complex molded part.

JEC Forum DACH‘s primary goal is to promote the DACH region’s dynamic composites ecosystem. Besides an extensive program of business meetings and conferences, innovation will have a special place in Augsburg from November 29 to 30, 2022 as attendees will have the opportunity to witness the JEC Composites Startup Booster and the AVK Awards. Winners of both competitions will be announced during a dedicated ceremony on November 29th.

The five finalists are:

BioWerkz: Closing the Loops
At BioWerkz a new bio-based, resource-efficient, and CO2-negative material called “NEWood” is developed,  using only wood waste and agricultural waste bound using fungal mycelium; the root network of mushrooms as a natural binder without the need for any synthetic binders.

Bufo Technology – HARDCORK: High-Performance Biobased Composite – Superior by nature
Bufo Technology has developed the high-performance composite material HARDCORK® made from cork, fibers and a thermosetting matrix. HARDCORK® can be manufactured as a core material, sandwich panel or complex molded part.

Cavicore: Water soluble salt cores for the production of hollow carbon fiber parts
CAVICORE produces ready-to-use water soluble cores for the realization of hollow composite parts. Their “lost cores” have the advantage of being temperature-resistant, stable as well as eco-friendly and recyclable, as they consist of pure salts without binders.

Composite Recycling: Closing the loop on Composite Materials
Composite Recycling has developed a highly energy efficient and sustainable process to separate the resin from the fibres. With the Ecole Polytechnique Fédérale de Lausanne, the team has designed a post-treatment to clean the fibres and make them reusable in new composites, closing the loop.

Microwave Solutions GmbH: Imagineering a sustainable future
Agile and modular microwave plasma and selective depolymerization technology for molecular recycling, fiber recovery and nanomaterial creation.

Mobile robot system for automated loading of a bobbin creel (c) STFI
12.05.2022

STFI with sustainable and digital innovations at Techtextil 2022

The Saxon Textile Research Institute (STFI) will be presenting innovative highlights from research and development at Techtextil 2022, the international trade fair for technical textiles and nonwovens. In addition to a warp-knitted textile façade greening in a modular system and textile lightweight construction elements for the building sector made from hemp as a renewable raw material, the STFI will also be showing innovations from nonwovens research. The project optiformTEX is an example of the nonwovens competence: in this project, the mass per unit area was specifically influenced for the production of semi-finished products in the automotive sector. Furthermore, the Chemnitz Institute exhibits an ecological foam coating for protective textiles. Central highlight of the STFI's presence at the fair is also a mobile robot system, which demonstrates the automated loading of a small-scale bobbin creel.

The Saxon Textile Research Institute (STFI) will be presenting innovative highlights from research and development at Techtextil 2022, the international trade fair for technical textiles and nonwovens. In addition to a warp-knitted textile façade greening in a modular system and textile lightweight construction elements for the building sector made from hemp as a renewable raw material, the STFI will also be showing innovations from nonwovens research. The project optiformTEX is an example of the nonwovens competence: in this project, the mass per unit area was specifically influenced for the production of semi-finished products in the automotive sector. Furthermore, the Chemnitz Institute exhibits an ecological foam coating for protective textiles. Central highlight of the STFI's presence at the fair is also a mobile robot system, which demonstrates the automated loading of a small-scale bobbin creel.

Highlights at Techtextil 2022
The greened façade tile is a system with which large building surfaces can be cost-effectively greened through a simple, modular segment structure. In addition to insulating the building, the system has been created to meet the design requirements of a modern city centre; low-maintenance greening is made possible through functional integration in the textile carrier layer and coordinated plant selection.

Moulded components made of natural fibre nonwovens are increasingly used in the automotive sector. Conventional nonwovens currently have uniform masses per unit area. Technical solutions for load-oriented component reinforcement and the resulting optimised use of materials represent an enormous economic potential. The basic idea of “optiformTEX” was therefore to specifically influence the mass per unit area distribution in the pile before the semi-finished product is consolidated. As a result, a textile-technological process and the corresponding plant component were successfully developed.

Future-oriented materials are offered by developments from the field of renewable raw materials in combination with bio-based resin systems: In the “Gro-Coce” project, an innovative ceiling system was developed by combining sustainable building products and methods. Currently, a high-performance hemp-based semi-finished product as well as the steps for its reproducible production by means of textile surface formation is developed by the research team. Initial application and load tests of the hemp-based semi-finished products on wooden beams confirmed the high performance potential of the natural fibre materials.

Special functional textiles are based on composite materials with coatings or membranes. The previous production of the coatings/membranes poses ecological and health risks. At STFI, solvent-free, purely aqueous coating systems and a technology for their application were therefore developed for the protective textile sector, resulting in a breathable, waterproof and wash-resistant textile coating.

The central highlight of the STFI's presence at the fair is a mobile robot system, which demonstrates the automated loading of a small-scale bobbin creel. At the STFI, the robot is part of the “textile factory of the future”, where a play mat is woven and processed step by step along the textile chain.

(c) Hexcel Corporation
29.04.2022

Hexcel Composite Solutions for the Automotive, Marine, Wind Energy and Recreation Markets at JEC World 2022

Hexcel will present a wide range of high-performance composite innovations for the Automotive, Marine, Wind Energy and Recreation markets during JEC World 2022 in Paris on May 3 – 5.

Hexcel will present a wide range of high-performance composite innovations for the Automotive, Marine, Wind Energy and Recreation markets during JEC World 2022 in Paris on May 3 – 5.

G-Vent Technology for Marine Structures
Hexcel has developed a new technology for out-of-autoclave (OoA) processing that delivers a game-changing reduction in process time and cost for marine manufacturers without compromising mechanical performance. Hexcel has leveraged its experience in aerospace and wind energy to develop its new G-Vent technology for OoA processing of highly loaded, thick section marine structures such as masts, foils, and wind-assisted ship propulsion (WASP) components. A full range of Hexcel marine prepregs are now available with integrated G-Vent technology, reducing the requirement for debulking steps and ensuring extremely low porosity (<1%) regardless of the laminate thickness. Leading marine non-destructive testing specialists Q.I. Composites recently confirmed that the thick section G-Vent panels they had evaluated had void contents and laminate quality in line with state-of-the-art autoclaved prepreg components. Visitors to the Hexcel stand will see a unique 400mm carbon cube cured in a single stage using 695 layers of HexPly M79 carbon fiber UD600 prepreg with G-Vent technology.

New HexPly® Nature Range Sustainable Prepregs
HexPly® Nature Range prepregs feature proven resins such as HexPly M49, M78 and M79 with bio-derived epoxy resin content. Created for use in all industrial markets, HexPly Nature Range materials can be seamlessly integrated into existing production processes, maintaining consistent mechanical performance and processing properties. A dedicated sustainability corner of the Hexcel stand will detail Nature Range products optimized for automotive, marine, wind energy and winter sport applications. The display will include an alpine ski produced by leading manufacturer Tecnica Group Ski Excellence Center which produces skis for Blizzard and for Nordica using HexPly Nature M78.1 UD flax prepreg material. In addition to the reduced environmental impact of the sustainably grown reinforcement, the flax fiber laminates also improve impact resistance and vibration damping in the ski.

HexPly® XF Surface Technology for Improved Part Surface Finish Quality
HexPly XF is a lightweight, semi-preg material that replaces traditional in-mold gel coat. It eliminates time-consuming refinishing work typically required to obtain a paint-ready surface and produces lighter, more consistent parts with shorter cycle times and a cleaner working environment. Visitors to the stand will see a composite panel illustrating a high-quality painted surface enabled with XF technology in a diverse range of industrial applications such as super yacht roof parts, Class A surface automotive panels, and both prepreg and infused wind turbine blades.

HexPly® M49 Prepreg for Automotive Visual Carbon Parts
HexPly M49 is easy to process and is especially suitable for visual carbon fiber-look applications such as the Brabus hood scoop on display on the Hexcel stand at JEC.

HexPly® Prepregs and HiMax® Reinforcements for Performance Marine Structures
Using a scale model of a Gunboat 68 performance sailing catamaran, Hexcel will illustrate how its HexPly and HiMax materials provide manufacturers with a complete set of lightweight composite solutions for high-performance marine structures. HexPly prepreg was selected for critical structural parts of the Gunboat 68 and provides very high mechanical performance including high dry and wet Tg.

Heavyweight HiMax reinforcements offer high deposition rates and remain easy to handle after cutting, making them highly suitable for industrial applications. In combination with a lightweight PrimeTex® woven fabric, the package of carbon fiber HiMax materials developed for the Gunboat 68 enabled consistent resin flow during infusion with reduced surface print-through.

Hexcel Fibers and Reinforcements for Lightweight Sporting Equipment
Sporting equipment manufacturers rely on Hexcel composite materials to deliver the ultimate performance at the lowest possible weight. Hexcel will exhibit a number of the latest high-performance sporting equipment applications such as a Bauer hockey stick featuring PrimeTex 98 gsm AS4C 3K fabric and a Corima tri-spoke cycling wheel made with lightweight Hexcel carbon fiber UD tape. Hexcel will also demonstrate how its HexTow® carbon fibers are used in key leisure and marine applications by displaying an AEROrazr solid carbon rigging component manufactured by spar and rigging manufacturer Future Fibres for the 36th America’s Cup.

 

Source:

Hexcel Corporation / 100% Marketing

Cobra
05.04.2022

COBRA to Sponsor and Manufacture JEC Trophies

Cobra International, leading manufacturer of advanced composite products for the water sports, automotive, marine, UAV, and industrial sectors, reinforces its long collaboration with the JEC Group by designing and manufacturing this year’s JEC Composites Innovation trophies. Cobra has designed and manufactured 35 composite material trophies for the JEC Composites Innovation and Start Up Booster competitions which will be presented during the 2022 awards ceremonies and throughout other JEC Group events in 2022.

Cobra International, leading manufacturer of advanced composite products for the water sports, automotive, marine, UAV, and industrial sectors, reinforces its long collaboration with the JEC Group by designing and manufacturing this year’s JEC Composites Innovation trophies. Cobra has designed and manufactured 35 composite material trophies for the JEC Composites Innovation and Start Up Booster competitions which will be presented during the 2022 awards ceremonies and throughout other JEC Group events in 2022.

The 2022 trophies are designed and produced by Cobra’s Design and Development department - the in house team that supports Cobra’s mass production operations with specialist expertise in product design, industrial design & prototyping. The sweeping curves of the trophies are influenced by perfume bottles, linking back to JEC’s French cultural heritage.  The design also combines a pallet of different materials to symbolise the JEC Group’s complete coverage of the composites sector. Acrylic, upcycled teak production waste from the furniture industry, Innegra™, flax, carbon, and aramid materials have been combined with Sicomin’s GreenPoxy 33 bio-resin to reference the award programme’s combined focus on innovation and sustainability.

The JEC Composites Innovation Awards are presented annually, recognising, and rewarding the most cutting-edge and ingenious projects that exploit the full potential of composite materials. Over the last 20 years, the JEC Composites Innovation and Startup programs have celebrated both innovation and partnership. The JEC Group will announce the winners for the 2022 JEC Composites Innovation awards on April 26th in Paris and in live streaming, and the Start-up Booster winners on May 3rd at JEC World.

“Cobra is delighted to reinforce its partnership with JEC Group, sponsoring and manufacturing the JEC trophies for 2022,” comments Danu Chotikapanich, CEO, Cobra.  “These are two of the most prestigious and respected awards programs within the composites industry and one that also matches Cobra’s ongoing commitment to innovation and sustainability improvements. Working with the latest bio resin technology, natural fibre reinforcements and upcycled composite and wood production waste materials our Design and Development team have created some stunning trophies for this year’s award season.”

Source:

COBRA International Co.,Ltd.

29.03.2022

SMCCreate 2022 design conference – programme available

SMCCreate 2022, the design conference jointly organized by the AVK and the European Alliance for SMC BMC takes place from 28-29 June 2022 in Antwerp, Belgium. Registrations are now possible.

This unique conference about design in SMC and BMC composite materials will provide valuable insights in the entire product design process from idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials.

Within the time of only 1.5 day, the SMCCreate 2022 conference will cover a wide range of subjects, all relevant for designers in their selection of materials solutions that provide performance, cost efficiency, manufacturing ability and sustainability.

Program
15 lectures by international speakers from France, Germany, Italy, Spain, The Netherlands and the USA will present practical presentations about sustainability, part design, mobility and automotive applications. Equally current trends and developments in the European SMC/BMC market are on the agenda.

SMCCreate 2022, the design conference jointly organized by the AVK and the European Alliance for SMC BMC takes place from 28-29 June 2022 in Antwerp, Belgium. Registrations are now possible.

This unique conference about design in SMC and BMC composite materials will provide valuable insights in the entire product design process from idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials.

Within the time of only 1.5 day, the SMCCreate 2022 conference will cover a wide range of subjects, all relevant for designers in their selection of materials solutions that provide performance, cost efficiency, manufacturing ability and sustainability.

Program
15 lectures by international speakers from France, Germany, Italy, Spain, The Netherlands and the USA will present practical presentations about sustainability, part design, mobility and automotive applications. Equally current trends and developments in the European SMC/BMC market are on the agenda.

Date and Location
The SMCCreate 2022 Conference will be organized on June 28-29, 2022 in the Hilton Hotel in Antwerp (Belgium). The presentation language will be English. The programme, further details and registration information is available at www.avk-tv.de.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

22.03.2022

JEC World announces 2023 and 2024 dates

JEC World announces the dates of the show in 2023, taking place from April 25 to 27, and in 2024, from March 5 to 7, in Paris Nord Villepinte in the same halls.
Taking place every year for more than half a century, JEC World gathers the whole value chain of composite materials in Paris. The event brings together not only all major stakeholders of the composites industry but is also the place to be for innovative startups in the field of advanced materials, and for experts, academics, scientists and R&D leaders. For professionals from the various application sectors of composite materials, it is a unique showcase of what composites can offer, and an unlimited source of inspiration. So, with this two-years schedule, professionals can plan their participation while ahead to make the most out the show.

JEC World announces the dates of the show in 2023, taking place from April 25 to 27, and in 2024, from March 5 to 7, in Paris Nord Villepinte in the same halls.
Taking place every year for more than half a century, JEC World gathers the whole value chain of composite materials in Paris. The event brings together not only all major stakeholders of the composites industry but is also the place to be for innovative startups in the field of advanced materials, and for experts, academics, scientists and R&D leaders. For professionals from the various application sectors of composite materials, it is a unique showcase of what composites can offer, and an unlimited source of inspiration. So, with this two-years schedule, professionals can plan their participation while ahead to make the most out the show.

More information:
JEC Group JEC World
Source:

JEC

13.03.2022

JEC Group supports Composites Expert To launch E-learning Composites Academy

On March 10th, JEC Group and Composites Expert have signed a partnership agreement to promote E-learning Composites Academy, the first 4.0 training platform dedicated to manufacturing processes of composite materials.

This partnership will start with two first steps: an introduction webinar session on March 15th at 4pm CET, and two sessions of training during JEC World 2022, on Tuesday, May 3rd and Wednesday, May 4th, in Paris where Composites Expert will present the E-learning Composites Academy, a new pedagogical approach aimed at appropriating knowledge of polymer transformation specially developed by Composites Expert.

Tools have been designed to combine the theoretical part (E-Learning course platform) and the practical part (BOXs, software, process simulator, exercises through manipulation) to observe complex phenomena, with the aim of mastering and optimising transformation processes. The aim of this presentation is to introduce people to the learning method and the interactivity of the teaching aids used in industry and education.

On March 10th, JEC Group and Composites Expert have signed a partnership agreement to promote E-learning Composites Academy, the first 4.0 training platform dedicated to manufacturing processes of composite materials.

This partnership will start with two first steps: an introduction webinar session on March 15th at 4pm CET, and two sessions of training during JEC World 2022, on Tuesday, May 3rd and Wednesday, May 4th, in Paris where Composites Expert will present the E-learning Composites Academy, a new pedagogical approach aimed at appropriating knowledge of polymer transformation specially developed by Composites Expert.

Tools have been designed to combine the theoretical part (E-Learning course platform) and the practical part (BOXs, software, process simulator, exercises through manipulation) to observe complex phenomena, with the aim of mastering and optimising transformation processes. The aim of this presentation is to introduce people to the learning method and the interactivity of the teaching aids used in industry and education.

“One of JEC Group’s objectives is to develop access to education to help the composites industry to attract and train talented professionals. So, we are very proud to announce this partnership and to support Composites Expert initiatives, as joining common efforts and strategies will benefit to the overall industry”, stated Anne-Carole Barbarin, Content and Product development Director.

“The partnership with JEC Group is a major step towards the development of our training platform, while several manufacturers have already supported us, such as Arkema, Chomarat, Daher, Diatex, Pinette PEI, Porcher, Sopara, joining JEC World to officially launch our platform is an amazing opportunity.”, stated Jean-Pierre Cauchois, CEO Composites Expert.

These training sessions are targeting companies’ employees who would like to improve their expertise, to study professional reconversion, the companies who would like to know more or use composite materials, and universities and school for students to go from theory to practical exercises.

Source:

JEC Group

(c) Dubai Museum of the Future
02.03.2022

Sicomin supports Dubai's Museum of the Future with fire-retardant epoxy solutions

Sicomin supported the build of Dubai’s Museum of the Future and supplied its bio-based intumescent gelcoat as well as fire-retardant laminating resins for the production of over 200 double curved panels making up the interior of the Museum’s entrance lobby.

The Museum of the Future, a new addition to Dubai’s skyline by architects Killa Design, engineers Buro Happold and contractor BAM International, opened last week on 22nd February 2022 and features a large percentage of composite materials in the interior construction.

Advanced Fiberglass Industries (AFI) manufactured 230 double curved interior panels, a double-helix DNA structure staircase that scales the full seven levels of the museum and 228 GRP oval shaped light structures for the museums car parking area.

Sicomin supported the build of Dubai’s Museum of the Future and supplied its bio-based intumescent gelcoat as well as fire-retardant laminating resins for the production of over 200 double curved panels making up the interior of the Museum’s entrance lobby.

The Museum of the Future, a new addition to Dubai’s skyline by architects Killa Design, engineers Buro Happold and contractor BAM International, opened last week on 22nd February 2022 and features a large percentage of composite materials in the interior construction.

Advanced Fiberglass Industries (AFI) manufactured 230 double curved interior panels, a double-helix DNA structure staircase that scales the full seven levels of the museum and 228 GRP oval shaped light structures for the museums car parking area.

Adaptable mould technology from Danish company Adapa, was introduced by Advanced Fiberglass Industries, Dubai (AFI) to ensure that the interior panels could be delivered in line with the project schedule. As well as allowing each panel shape to be rapidly configured without the machining of traditional moulds, the adaptive mould technology massively reduced waste generated in the moulding process, contributing to the building’s low carbon LEED platinum credentials.

With a challenging structural and fire safety specification defined, Sicomin’s bio-based SGi128 intumescent gelcoat and SR1122 fire retardant laminating epoxy were chosen for the panels, an additional advantage being that in addition to high fire properties, SGi 128 is also formulated with over 30% carbon from renewable sources, reducing the final carbon footprint significantly.  

Sicomin worked alongside the panel manufacturer, providing technical support for the fire test panels and the initial Adapa moulding trials.

Source:

Sicomin / 100% Marketing