From the Sector

Reset
92 results
DITF: Lignin coating for Geotextiles Photo: DITF
Coating process of a cellulose-based nonwoven with the lignin compound using thermoplastic processing methods on a continuous coating line.
27.10.2023

DITF: Lignin coating for Geotextiles

Textiles are a given in civil engineering: they stabilize water protection dams, prevent runoff containing pollutants from landfills, facilitate the revegetation of slopes at risk of erosion, and even make asphalt layers of roads thinner. Until now, textiles made of highly resistant synthetic fibers have been used for this purpose, which have a very long lifetime. For some applications, however, it would not only be sufficient but even desirable for the auxiliary textile to degrade in the soil when it has done its job. Environmentally friendly natural fibers, on the other hand, often decompose too quickly. The German Institutes of Textile and Fiber Research Denkendorf (DITF) are developing a bio-based protective coating that extends their service life.

Textiles are a given in civil engineering: they stabilize water protection dams, prevent runoff containing pollutants from landfills, facilitate the revegetation of slopes at risk of erosion, and even make asphalt layers of roads thinner. Until now, textiles made of highly resistant synthetic fibers have been used for this purpose, which have a very long lifetime. For some applications, however, it would not only be sufficient but even desirable for the auxiliary textile to degrade in the soil when it has done its job. Environmentally friendly natural fibers, on the other hand, often decompose too quickly. The German Institutes of Textile and Fiber Research Denkendorf (DITF) are developing a bio-based protective coating that extends their service life.

Depending on humidity and temperature, natural fiber materials can degrade in the soil in a matter of months or even a few days. In order to significantly extend the degradation time and make them suitable for geotextiles, the Denkendorf team researches a protective coating. This coating, based on lignin, is itself biodegradable and does not generate microplastics in the soil. Lignin is indeed biodegradable, but this degradation takes a very long time in nature.

Together with cellulose, Lignin forms the building materials for wood and is the "glue" in wood that holds this composite material together. In paper production, usually only the cellulose is used, so lignin is produced in large quantities as a waste material. So-called kraft lignin remains as a fusible material. Textile production can deal well with thermoplastic materials. All in all, this is a good prerequisite for taking a closer look at lignin as a protective coating for geotextiles.

Lignin is brittle by nature. Therefore, it is necessary to blend the kraft lignin with softer biomaterials. These new biopolymer compounds of brittle kraft lignin and softer biopolymers were applied to yarns and textile surfaces in the research project via adapted coating systems. For this purpose, for example, cotton yarns were coated with lignin at different application rates and evaluated. Biodegradation testing was carried out using soil burial tests both in a climatic chamber with temperature and humidity defined precisely according to the standard and outdoors under real environmental conditions. With positive results: the service life of textiles made of natural fibers can be extended by many factors with a lignin coating: The thicker the protective coating, the longer the protection lasts. In the outdoor tests, the lignin coating was still completely intact even after about 160 days of burial.

Textile materials coated with lignin enable sustainable applications. For example, they have an adjustable and sufficiently long service life for certain geotextile applications. In addition, they are still biodegradable and can replace previously used synthetic materials in some applications, such as revegetation of trench and stream banks.

Thus, lignin-coated textiles have the potential to significantly reduce the carbon footprint: They reduce dependence on petroleum-based products and avoid the formation of microplastics in the soil.

Further research is needed to establish lignin, which was previously a waste material, as a new valuable material in industrial manufacturing processes in the textile industry.

The research work was supported by the Baden-Württemberg Ministry of Food, Rural Areas and Consumer Protection as part of the Baden-Württemberg State Strategy for a Sustainable Bioeconomy.

Source:

Deutsche Institute für Textil- und Faserforschung Denkendorf (DITF)

Cinte Techtextil China 2023 with different zones (c) Messe Frankfurt (HK) Ltd
14.09.2023

Cinte Techtextil China 2023 with different zones

Technological progress often results from close collaboration, and industries that rely on continual improvement stand to benefit from the return to in-person business. Cinte Techtextil China’s first edition since eased pandemic measures is set to reflect a 27.9% increase in exhibitor numbers, with a rejuvenated international contingent further supplemented by the return of the European Zone. Taking place from 19 – 21 September across 40,000 sqm at the Shanghai New International Expo Centre, the platform is expected to welcome buyers from across Asia, Europe, and beyond. Pre-registrations have doubled compared to the previous edition, and international buyers account for over 20% of the total.

The new zone, Marine Textile Zone, will be comprised of multiple Chinese green marine and nautical rope netting exhibitors, while also hosting the Technology Exchange Forum, and the awards ceremony of the Top 10 Suppliers in the China Rope Net Industry. Prominent exhibitors in this zone include Ropenet Group, Hunan Xinhai, and Zhejiang Four Brothers Rope.

Technological progress often results from close collaboration, and industries that rely on continual improvement stand to benefit from the return to in-person business. Cinte Techtextil China’s first edition since eased pandemic measures is set to reflect a 27.9% increase in exhibitor numbers, with a rejuvenated international contingent further supplemented by the return of the European Zone. Taking place from 19 – 21 September across 40,000 sqm at the Shanghai New International Expo Centre, the platform is expected to welcome buyers from across Asia, Europe, and beyond. Pre-registrations have doubled compared to the previous edition, and international buyers account for over 20% of the total.

The new zone, Marine Textile Zone, will be comprised of multiple Chinese green marine and nautical rope netting exhibitors, while also hosting the Technology Exchange Forum, and the awards ceremony of the Top 10 Suppliers in the China Rope Net Industry. Prominent exhibitors in this zone include Ropenet Group, Hunan Xinhai, and Zhejiang Four Brothers Rope.

Other domestic exhibitors, such as Shanghai Shenda Kebao New Materials, SIJIA New Material (Shanghai), Zhejiang Hailide New Material, and Zhejiang Jinda New Materials, will showcase products for applications in outdoor advertising, tents, boats, vehicles, environmental engineering, and much more.

Supplementing the fairground’s wide variety of domestic suppliers will be a much-increased showing of international exhibitors, with many to be found within hall E1’s European Zone. Several global industry leaders are featured in their categories below:

Nonwovens equipment

  • Autefa Solutions, Germany: solutions provider for nonwovens lines and machines for carded-crosslapped needlepunching lines, spunlace lines and thermobonding lines.
  • Dilo, Germany: in addition to offering general services, Dilo supplies opening and blending equipment, carding and airlay machines, and crosslapping and needling machines.
  • Groz-Beckert, Germany: provider of industrial machine needles, precision parts and fine tools, as well as systems and services for the production and joining of textile fabrics.
  • Reifenhäuser Reicofil, Germany: provider of innovative technologies and components for plastics extrusion, producing blown films, cast films, sheets as well as nonwovens.

Weaving equipment

  • Itema, Italy: provider of advanced weaving machines, spare parts, and integrated services, specifically for rapier, air jet and projectile weft insertion technologies.
  • Lindauer DORNIER, Germany: the company manufactures weaving machines, film stretching lines, and composite systems, also offering technical support and spare parts supply.
  • Picanol, Belgium: producer and servicer of high-tech air jet and rapier weaving machines, with around 2,600 weaving mills utilising their systems worldwide.

Coating and lamination

  • BRÜCKNER Textile Technologies, Germany: manufacturer of machines and lines for the coating and finishing of apparel fabric, technical textiles, nonwovens, glass fabrics and floor coverings.
  • ROWA Lack, Germany: developer of high-quality materials and product solutions for the polymer industry, with applications including automotive, electrical engineering, construction, technical textiles, and medical technology.
  • Stahl, the Netherlands: the Dutch company provides high quality coatings, dyes and process chemicals for leather, flexible coated substrates, textiles, films and foils, paper, and related products.

Fibre

  • Monosuisse, Switzerland: with production sites in Switzerland, Poland, Romania, Mexico, and Germany, Monosuisse manufactures various precise, high-quality polymer monofilaments from 19µm to 3.00 mm in diameter.
  • Perlon, Germany: specialised in the manufacture of synthetic filaments in diverse application areas, including paper machine clothing, dental care, and advanced technical textiles for agriculture, 3D printing, sports and leisure, home, and more.

Meanwhile, first-time exhibitors include Rökona (Germany), showcasing RE:SPACE, their range of recycled technical textiles; Testex AG (Switzerland), the official OEKO-TEX® representative in multiple countries including China; Hohenstein (Germany), the renowned testing laboratory and research institute; and zwissTEX (Germany), the knitted fabrics and lamination specialists. In addition, the returning Taiwan Pavilion is set to feature the debut of Shinih Enterprise Co Ltd (Taiwan China).

Beyond the innovation displayed at the booths, the fair’s programme is set to welcome global experts from various technical textile and nonwoven sub-sectors to offer specific insights and unveil innovations. Highlighted events include:

The 11th China International Nonwovens Conference
14 sessions cover topics such as the quality control of medical supplies; green development in technology and applications in the nonwovens industry; and the development and application of flashspun nonwovens in China.

Marine textiles and rope netting events
Events specific to this zone include the Top 10 Suppliers in the China Rope Net Industry; Conference on Textile Applications for Marine Engineering and Fisheries; and the China Nonwovens & Industrial Textiles Association (CNITA) Rope Net Branch Council Meeting

"Nonwovens, Creating a Better Life” Innovation Showcase
Product display area showcasing around 100 nonwovens products with applications in five areas: medical and health, quality of life, human habitat, sustainable development, and innovative design.

Advanced Technical Textiles Industry Chain Synergistic Innovation Development Forum
Includes presentations from multiple key players in the technical textile industry, including Mr Steven Liu, Commercial Manager of Polymer Additives Business of Sanitized (China) Ltd.

Source:

Messe Frankfurt (HK) Ltd

05.09.2023

Beaulieu International Group at International Conference on Geosynthetics

Beaulieu International Group will turn the spotlight on geotextile products with sustainability benefits to support progress in resilient civil engineering projects at the 12th ICG Rome from 18th -21st September 2023, presenting options to target fossil carbon reduction by choosing PP-based staple fibres or woven geotextiles that are among the lowest in carbon footprint for geosynthetics.

For manufacturers of nonwoven geotextiles, Beaulieu Fibres International (BFI) offers PP fibres with > 25% carbon footprint reduction compared to the European standard PP fibres, generating 1.48 kg CO2/kg PP fibres. A step further is to accelerate the replacement of fossil carbon in engineered fibre applications by choosing its ISCC Plus certified bio-attributed MONO-PP with a negative carbon footprint.

For construction projects, nonwoven geotextiles made with high-tenacity HT8 fibres are proven to secure a longer service lifetime and reduce the environmental impact, as they offer high mechanical performance at a reduced weight.

Beaulieu International Group will turn the spotlight on geotextile products with sustainability benefits to support progress in resilient civil engineering projects at the 12th ICG Rome from 18th -21st September 2023, presenting options to target fossil carbon reduction by choosing PP-based staple fibres or woven geotextiles that are among the lowest in carbon footprint for geosynthetics.

For manufacturers of nonwoven geotextiles, Beaulieu Fibres International (BFI) offers PP fibres with > 25% carbon footprint reduction compared to the European standard PP fibres, generating 1.48 kg CO2/kg PP fibres. A step further is to accelerate the replacement of fossil carbon in engineered fibre applications by choosing its ISCC Plus certified bio-attributed MONO-PP with a negative carbon footprint.

For construction projects, nonwoven geotextiles made with high-tenacity HT8 fibres are proven to secure a longer service lifetime and reduce the environmental impact, as they offer high mechanical performance at a reduced weight.

Beaulieu Technical Textiles' (BTT) woven geotextiles provide a wide range of functions, including separation, filtration, reinforcement and erosion control, and are among the most sustainable in the industry. Depending on weight, the carbon footprint of its woven geotextiles (m²) ranges between 0.37 and 1.40 kg CO2 eq./m². They also minimize the use of natural resources for more sustainable infrastructure development. Case studies such as at the Ostend-Bruges airport highlight significant CO2 reduction on the jobsite by replacing the transport of 960 trucks of gravel with 3 trucks of woven geotextiles, and by extending the runway’s life span.

The ICG launch of its new line Terralys MF woven filtration geotextiles with monofilament boosts the performance of a common solution in building layers that require high water flow rates. High-tenacity extruded polypropylene tapes and monofilaments are interwoven to form dimensionally stable and highly permeable geotextiles. These new filtration geotextiles provide greater resistance to dirt and biological clogging. They allow water to travel freely while reducing soil erosion when employed as a separation and stabilizing layer.

As of September 2023, all PP staple fibres and woven geotextiles will have Environmental Product Declarations (EPD) based on LCAs. Each EPD is an essential tool for communicating and reporting on the sustainability performance and helps carbon-conscious customers in their purchasing and decision making. Registered EPDs are globally recognized, publicly available and free to download through EPD Libraries.

Source:

Beaulieu International Group

Toray Composite Materials America: Boeing Supplier of the Year Photo Toray
04.09.2023

Toray Composite Materials America: Boeing Supplier of the Year

Toray Composite Materials America, Inc. headquartered in Tacoma, Washington, has been awarded the "Boeing Supplier of the Year" award, a leadership-nominated award given to supplier companies that support and propel Boeing's strategic objectives through risk-sharing and enduring partnerships. This year, 12 companies were selected from among 11,000 Boeing suppliers worldwide, and CMA was selected as one of them for the Alliance Award. This is Toray's second award from Boeing, receiving the Supplier of the Year Excellence Award in 2019.

Toray began supplying Boeing in 1975 when it first qualified TORAYCA™ T300 carbon fiber for commercial application on the Boeing 737. Since then, Toray has provided high-performance carbon fiber and highly toughened, primary structure carbon fiber composite prepreg on various programs.

The trophy was presented by William A. Ampofo II, Vice President of Parts & Distribution Services and Supply Chain for Boeing Global Services and Chair of the Supply Chain Operations Council to CMA.

Toray Composite Materials America, Inc. headquartered in Tacoma, Washington, has been awarded the "Boeing Supplier of the Year" award, a leadership-nominated award given to supplier companies that support and propel Boeing's strategic objectives through risk-sharing and enduring partnerships. This year, 12 companies were selected from among 11,000 Boeing suppliers worldwide, and CMA was selected as one of them for the Alliance Award. This is Toray's second award from Boeing, receiving the Supplier of the Year Excellence Award in 2019.

Toray began supplying Boeing in 1975 when it first qualified TORAYCA™ T300 carbon fiber for commercial application on the Boeing 737. Since then, Toray has provided high-performance carbon fiber and highly toughened, primary structure carbon fiber composite prepreg on various programs.

The trophy was presented by William A. Ampofo II, Vice President of Parts & Distribution Services and Supply Chain for Boeing Global Services and Chair of the Supply Chain Operations Council to CMA.

Source:

Toray

ropes Photo Cinte Techtextil
29.08.2023

Cinte Techtextil China 2023 to launch new Marine Textile Zone

At the crosswinds of China’s 14th Five-Year Plan for the Development of the Marine Economy and its 14th Five-Year Guidance for the Development of the Technical Textiles Industry lies the marine textile sub-sector. Following the government’s directive, the Marine Textile Zone will be unfurled at this year’s fair, taking place from 19 – 21 September 2023 at the Shanghai New International Expo Centre. Multiple exhibitors from across China have confirmed their participation within the zone, which will be comprised of three main parts: green marine science and nautical rope netting innovation display area, the Technology Exchange Forum, and the awards ceremony of the Top 10 Suppliers in the China Rope Net Industry.
 
The global rope market is predicted to experience a CAGR of 5.6% and grow by over USD 4 billion between 2022 - 2027[1], and suppliers are eager for the chance to meet buyers face to face. In fact, many will use the new zone at Asia’s leading technical textiles and nonwovens fair to do so.

At the crosswinds of China’s 14th Five-Year Plan for the Development of the Marine Economy and its 14th Five-Year Guidance for the Development of the Technical Textiles Industry lies the marine textile sub-sector. Following the government’s directive, the Marine Textile Zone will be unfurled at this year’s fair, taking place from 19 – 21 September 2023 at the Shanghai New International Expo Centre. Multiple exhibitors from across China have confirmed their participation within the zone, which will be comprised of three main parts: green marine science and nautical rope netting innovation display area, the Technology Exchange Forum, and the awards ceremony of the Top 10 Suppliers in the China Rope Net Industry.
 
The global rope market is predicted to experience a CAGR of 5.6% and grow by over USD 4 billion between 2022 - 2027[1], and suppliers are eager for the chance to meet buyers face to face. In fact, many will use the new zone at Asia’s leading technical textiles and nonwovens fair to do so.

In the green marine and rope netting category, exhibitors will showcase the latest innovations along the marine textile industry chain, anchored by application areas such as marine engineering, marine economy, marine fencing, marine rescue, deep-sea fishing, deep-sea aquaculture, and many more.

Featured exhibitors include:

  • Ropenet Group: covering 36 application areas, such as aerospace, marine fisheries, safety protection, and emergency rescue, the Shandong-based company has exported to over 110 countries and regions. Products include ropes, nets, threads, and belts, with new materials and high-performance synthetic fibre spinning ropes forming the core of its business.
  • Hunan Xinhai: with its Hunan factory covering 200,000 sqm, its industry-leading rope net production scale ensures it can service multiple sectors such as fisheries, sports, military industry, marine engineering, life-saving protection, and many more. Its extensive network spans Asia, Africa, Europe, and beyond.
  • Zhejiang Four Brothers Rope: located in Zhejiang Toumen Port Economic Development Zone, the special chemical fibre rope manufacturer integrates R&D, manufacturing, sales, and after-sales service. After nearly 60 years of operation, the company now has a yearly production capacity of over 15,000 tons.

Other notable exhibitors in this zone include Xuzhou Henghui Braiding Machine; Shandong Jinguan Netting; Jiuli Rope; and Zhejiang Hailun Rope Net.

Meanwhile, the Technology Exchange Forum will focus on policies and regulations, strategic development opportunities, market analysis, product and process innovation, and the promotion and application of marine textiles. A range of well-known international and domestic experts have been invited to deliver comprehensive industry analysis, and unveil oceanic green textile initiatives onsite.

Designed to expand the influence of the rope net industry, the Top 10 Suppliers in the China Rope Net Industry awards will highlight enterprises currently making key contributions. Other fringe events related to this textile sub-sector include the Conference on Textile Applications for Marine Engineering and Fisheries, and the China Nonwovens & Industrial Textiles Association (CNITA) Rope Net Branch Council Meeting.

Lastly, the Marine Textile Zone will also encompass a business negotiation area to facilitate negotiations between key players onsite, set against the backdrop of the innovation display area’s award-winning and patented rope net products. As a whole, the zone is expected to encourage independent innovation in marine science and technology, coordinate the protection and development of marine resources, and help build a modern maritime industrial system.

The fair’s product categories cover 12 application areas, which comprehensively span a full range of potential uses in modern technical textiles and nonwovens. These categories also cover the entire industry, from upstream technology and raw materials providers to finished fabrics, chemicals and other solutions. This scope of product groups and application areas ensures that the fair is an effective business platform for the entire industry.

The fair is organised by Messe Frankfurt (HK) Ltd; the Sub-Council of Textile Industry, CCPIT; and the China Nonwovens & Industrial Textiles Association (CNITA).

Source:

Messe Frankfurt (HK) Ltd

09.08.2023

Carrington Textiles and Pincroft Debut at DALO Industry Days

The Danish Ministry of Defence Acquisition and Logistics Organisation (DALO) Industry Days event is scheduled to take place from 23rd to 24th August in Denmark. Carrington Textiles and their main manufacturing facility in the UK, Pincroft, will showcase their latest innovations in military textiles.

Carrington Textiles - after recently announcing the launch of the new stretch military ripstop fabric, Spartan HT Flex Lite, and strategically appointing the new Head of Defence and Security Fabrics -  at the event represents the commercial focus on building on an over 90 years of heritage of manufacturing military fabrics.

Likewise, Pincroft’s latest technology in non-skin contact vector protection for defence textiles and the recent involvement in printing the new Dutch Ministry of Defence’s camouflage pattern as part of their army’s uniform programme, are just a few of the textile services that will be presented at the event.

The Danish Ministry of Defence Acquisition and Logistics Organisation (DALO) Industry Days event is scheduled to take place from 23rd to 24th August in Denmark. Carrington Textiles and their main manufacturing facility in the UK, Pincroft, will showcase their latest innovations in military textiles.

Carrington Textiles - after recently announcing the launch of the new stretch military ripstop fabric, Spartan HT Flex Lite, and strategically appointing the new Head of Defence and Security Fabrics -  at the event represents the commercial focus on building on an over 90 years of heritage of manufacturing military fabrics.

Likewise, Pincroft’s latest technology in non-skin contact vector protection for defence textiles and the recent involvement in printing the new Dutch Ministry of Defence’s camouflage pattern as part of their army’s uniform programme, are just a few of the textile services that will be presented at the event.

Source:

Carrington Textiles

OETI purchases ECS to expand its PPE portfolio photo: OETI
12.07.2023

OETI purchases ECS to expand its PPE portfolio

OETI – a member of the internationally active TESTEX Group – has bought the German company ECS to expand its service portfolio in the field of personal protective equipment (PPE).

OETI has been offering testing services for textile work clothing since 1983 – for about 40 years. Since the introduction of CE labelling for personal protective equipment and the enactment of the PPE Directive by the European Union in 1993, OETI has not only been testing textile personal protective equipment, but now on also certifies it in conformity with EU standards. In 1995, OETI was certified in Brussels as a Notified Body (0534) for type-examinations and quality assurance monitoring of personal protective equipment end products. Testing and certification is carried out in accordance with the current PPE Regulation (EU) 2016/425.

Testing and Certification Body for Eye and Face Protection, based in Aalen, was founded 15 years ago and is a globally active institution for testing and certification of eye and face protection equipment. The company is one of the leading independent testing institutions for personal protection products in laser applications and for welding work.

OETI – a member of the internationally active TESTEX Group – has bought the German company ECS to expand its service portfolio in the field of personal protective equipment (PPE).

OETI has been offering testing services for textile work clothing since 1983 – for about 40 years. Since the introduction of CE labelling for personal protective equipment and the enactment of the PPE Directive by the European Union in 1993, OETI has not only been testing textile personal protective equipment, but now on also certifies it in conformity with EU standards. In 1995, OETI was certified in Brussels as a Notified Body (0534) for type-examinations and quality assurance monitoring of personal protective equipment end products. Testing and certification is carried out in accordance with the current PPE Regulation (EU) 2016/425.

Testing and Certification Body for Eye and Face Protection, based in Aalen, was founded 15 years ago and is a globally active institution for testing and certification of eye and face protection equipment. The company is one of the leading independent testing institutions for personal protection products in laser applications and for welding work.

ECS tests and evaluates occupational health and safety goggles with and without a filter action, passive and active switching protection filters and shields for welders, and laser protection filters, goggles, and shields. The company also tests the optical properties of sunglasses, sports glasses, ski goggles, swimming goggles and motorbike goggles.

With OETI’s takeover, the ECS location in Aalen is retained, and all employees will continue working at ECS. The new Managing Director of ECS GmbH as of 1 July 2023 is Dipl.-Ing. Rolf Diebolder.

‘We are present on the European market, on the American market and, via a representative office, on the Chinese market. With the aid of the new distribution channels through OETI and TESTEX, we want to steadily advance ECS’ expansion and be present on all five continents’, says Managing Director Rolf Diebolder, explaining his strategic plans for ECS. ‘I would like OETI and ECS to develop a joint strategy in order to be able to offer existing and new customers of both companies a complete package which, when combined, will give us a unique selling point in the marketplace’, says Diebolder.

Diebolder also sees further potential in the cooperation with regard to protective laser clothing. According to him, this is where the laser laboratory commissioned by ECS could be used to make textiles laser-safe. In the future, there will be more and more ‘hand-held’ devices, i.e. laser welding devices, for which gloves and protective jackets are needed.

Source:

OETI - Institut fuer Oekologie, Technik und Innovation GmbH

(c) KARL MAYER GROUP
02.06.2023

KARL MAYER GROUP with sustainable technical textiles at ITMA

KARL MAYER GROUP will be presenting a WEFTTRONIC® II G at the ITMA with new features and upgrades for greater efficiency. This warp knitting machine with weft insertion produces lattice structures from high-strength polyester, which are firmly established in the construction industry in particular. With a working width of 213", it offers productivity and further advantages through design innovations. New features include weft thread tension monitoring, management and the new VARIO WEFT laying system. The component for the weft insertion aims at maximum flexibility. It allows the patterning of the weft yarn to be changed quickly and easily electronically, without mechanical intervention during yarn insertion and without limits on repeat lengths. In addition, there is less waste.

KARL MAYER GROUP will be presenting a WEFTTRONIC® II G at the ITMA with new features and upgrades for greater efficiency. This warp knitting machine with weft insertion produces lattice structures from high-strength polyester, which are firmly established in the construction industry in particular. With a working width of 213", it offers productivity and further advantages through design innovations. New features include weft thread tension monitoring, management and the new VARIO WEFT laying system. The component for the weft insertion aims at maximum flexibility. It allows the patterning of the weft yarn to be changed quickly and easily electronically, without mechanical intervention during yarn insertion and without limits on repeat lengths. In addition, there is less waste.

The KARL MAYER GROUP also supports its customers with well thought-out Care Solutions. The new support offers include retrofit packages for retrofitting control and drive technology for weft insertion and composite machines, and service packages that bundle various services. These include machine inspections and the replacement of all drive belts. The customer benefits from fixed prices that cover the costs of technician assignments, various discount options and transparent services.

A new solution for the vertical greening of cities is presented from the field of application for technical textiles. The core of the innovation is a grid textile produced on warp knitting machines with weft insertion by KARL MAYER Technische Textilien GmbH. The knitted lattice fabric is made of flax. It is used as a climbing aid for fast-growing plants, and after the greening phase, in autumn, it can be recycled together with these plants as biomass in pyrolysis plants to produce electricity and activated carbon. In summer, the planted sails lower the ambient temperature through evaporation effects. In addition, photosynthesis creates fresh air and binds CO2. Other important advantages are low soil requirements and flexible placement in public spaces. The greening system was developed by the company Micro Climate Cultivation, OMC°C, with the support of KARL MAYER Technische Textilien.

The KARL MAYER GROUP will also be exhibiting a sustainable composite solution made from natural fibres. The reinforcing textile of the innovative lightweight material is a multiaxial non-crimp fabric, which was also produced from the bio-based raw material flax on a COP MAX 4 from KARL MAYER Technische Textilien. The boatbuilding specialist GREENBOATS uses natural fibre composites to achieve sustainable products. The fact that it succeeds in this is shown, for example, by the Global Warming Potential (GWP): 0.48 kg of CO2 per kilogram of flax reinforcement compares with 2.9 kg of CO2 per kilogram of glass textile.

Source:

KARL MAYER Verwaltungsgesellschaft mbH

12.04.2023

Comeback of CIOSH trade fair in Shanghai

As a trade fair for safety and occupational health in China, the 104th China International Occupational Safety & Health Goods Expo (CIOSH 2023), organized by China Textile Commerce Association (CTCA) and Messe Düsseldorf (Shanghai) Co., Ltd. (MDS), will be grandly held at the Shanghai New International Expo Centre (SNIEC) Hall E1-E7 from 13-15 April 2023. Following three years of epidemic prevention and control measures, the situation has stabilized in China, allowing the labor protection market to enter a phase of rapid recovery and rebound. CIOSH 2023 will attract over 1,500 exhibitors from 14 countries, showcasing their latest protective equipment and technology in an exhibition area exceeding 80,000 square meters.

As a trade fair for safety and occupational health in China, the 104th China International Occupational Safety & Health Goods Expo (CIOSH 2023), organized by China Textile Commerce Association (CTCA) and Messe Düsseldorf (Shanghai) Co., Ltd. (MDS), will be grandly held at the Shanghai New International Expo Centre (SNIEC) Hall E1-E7 from 13-15 April 2023. Following three years of epidemic prevention and control measures, the situation has stabilized in China, allowing the labor protection market to enter a phase of rapid recovery and rebound. CIOSH 2023 will attract over 1,500 exhibitors from 14 countries, showcasing their latest protective equipment and technology in an exhibition area exceeding 80,000 square meters.

Integrating Online and Offline Platforms
CIOSH 2023 encompasses four major sectors: Safety at Work, Security at Work, Health at Work, and Emergency Rescue Management. Renowned domestic and international exhibitors, including 3M, Honeywell, Ansell, SATA, JSP, MSA, DELTAPLUS, Lakeland, Cortina, UVEX, CM Chaomei, Xing Yu Gloves, DS, East Asia Glove, Hanvo, SOMO Zhongmai Safety, SAFETY-INXS, and TELPS, will assemble on site. At the same time, CIOSH 2023 has introduced an innovative online platform - CIOSH VIRTUAL. By offering online displays, live streaming, interactive features, and real-time communications, it breaks time and space constraints, facilitating exhibitors and visitors to continue their business exchanges and cooperations beyond the physical exhibition. So far, nearly 1,300 companies have joined the CIOSH VIRTUAL, showcasing more than 3,000 products online and attracting over 70,000 views.

CIOSH Industry Technical Seminar, Sustainable Development Emerges as the Key Focus
The annual Industry Technical Seminar, held concurrently with CIOSH, serves as a platform for professionals to discuss product solutions, share industry insights, and exchange ideas on relevant policies. In 2021, China integrated climate change mitigation measures into its 14th Five-Year Plan, established a 2030 carbon peaking action plan, and proactively pursued the goal of carbon neutrality by 2060. Under the development objectives of "carbon peaking" and "carbon neutrality," the sustainable development of the personal protective equipment (PPE) industry has become the primary theme of this year's seminar. Experts from China Carbon Low-carbon Certification (Jiangsu) Co., Ltd., China Certification Centre, Inc., and SGS-CSTC Standards Technical Services Co., Ltd., will examine related policies, the effects of "carbon neutrality" on the PPE industry chain and the industries using PPE from different angles. They will also explore the future direction of PPE and offer professional guidance for the transformation of relevant enterprises.

Fall Protection Zone
Falls from height are one of the most common accidents that cause serious injury or death to workers. Effective fall protection requires not only protective equipment, but also professional instructions and training. Therefore, CIOSH set up a new Fall Protection Zone in 2021, which received unanimous acclaim. CIOSH 2023 has continued to invite SKYLOTEC, rothoblaas, JECH, Mode and NTR Safety, five companies that specialize in protection at height, to conduct on-site demonstrations on fall testing, fall protection solutions and aerial rescue, and provide visitors with the most professional fall protection guidance and training.

Occupational Health
CIOSH has always implemented the strategy of expanding the business scope in a diversified way, which devotes itself to providing innovative opportunities and new driving forces for the sustainability of the occupational safety and health industry. This year, focusing on the "occupational health" sector, the exhibition will launch an Ergonomics Zone and an Exoskeleton Technology Zone for the first time.

Photo Autoneum Management AG
19.12.2022

Autoneum: Optimized thermal management for electric vehicles thanks to cold chamber

A new cold chamber at its headquarters in Winterthur, Switzerland, enables Autoneum to optimize existing technologies as well as simulation and engineering services in vehicle thermal management and to adapt them to the changing thermal requirements of electric vehicles

The absence of heat from the internal combustion engine in electric vehicles as well as the impact of ambient temperature on the performance and lifetime of lithium-ion batteries are changing the requirements for vehicle thermal management. In addition, the energy from the battery is used not only to power the e-motor but also to thermally manage the battery itself and to warm and cool the car cabin by means of the heating, ventilation and air conditioning system. To increase the thermal comfort of the occupants and at the same time ensure optimum battery performance, save energy and thus increase the car’s range, manufacturers are placing increasing emphasis on efficient overall thermal management of the vehicle.

A new cold chamber at its headquarters in Winterthur, Switzerland, enables Autoneum to optimize existing technologies as well as simulation and engineering services in vehicle thermal management and to adapt them to the changing thermal requirements of electric vehicles

The absence of heat from the internal combustion engine in electric vehicles as well as the impact of ambient temperature on the performance and lifetime of lithium-ion batteries are changing the requirements for vehicle thermal management. In addition, the energy from the battery is used not only to power the e-motor but also to thermally manage the battery itself and to warm and cool the car cabin by means of the heating, ventilation and air conditioning system. To increase the thermal comfort of the occupants and at the same time ensure optimum battery performance, save energy and thus increase the car’s range, manufacturers are placing increasing emphasis on efficient overall thermal management of the vehicle.

The chamber enables to test both occupants’ subjective perception of thermal comfort and the performance of components and entire vehicles under controlled temperature conditions of up to minus 20 degrees Celsius. It is thus a valuable addition to the existing testing and bench-marking facilities at the Company’s global research and development centers. The tests conducted in the chamber show how existing insulating components such as under battery shields, carpets and interior trim need to be optimized to further enhance the thermal management of the vehicle battery and cabin. The tests also provide valuable insights regarding the development and optimization of heated surfaces such as floor mats and door trim panels to improve thermal performance and driver comfort of electric vehicles.

Source:

Autoneum Management AG

24.11.2022

EURATEX: A price cap at 275€/MWh would be meaningless

The plan of the European Commission to propose a price cap on wholesale gas price at 275€/MWh would be a bitter disappointment for the European textiles and clothing manufacturers, said EURATEX.

November 22nd, EURATEX stated in a letter to EC President, Ursula von der Leyen, that any price cap above the level of 80€euro/MWh would not help the EU industry – the textile sector in particular – to survive the current crisis. Indeed as early as July 2021, the wholesale gas price in the EU was below 30€/MWh. Now, the EU industry is facing gas and energy prices that have exceeded any coping capacity: from the record-high 320€/MWh last August, the price has reached to 127€/MWh today. Still, it is more than 300% than the business as usual prices.

The plan of the European Commission to propose a price cap on wholesale gas price at 275€/MWh would be a bitter disappointment for the European textiles and clothing manufacturers, said EURATEX.

November 22nd, EURATEX stated in a letter to EC President, Ursula von der Leyen, that any price cap above the level of 80€euro/MWh would not help the EU industry – the textile sector in particular – to survive the current crisis. Indeed as early as July 2021, the wholesale gas price in the EU was below 30€/MWh. Now, the EU industry is facing gas and energy prices that have exceeded any coping capacity: from the record-high 320€/MWh last August, the price has reached to 127€/MWh today. Still, it is more than 300% than the business as usual prices.

The very existence of the European industry is at stake and with it the European sustainability agenda – and Europe’s capacity to implement it. Furthermore, Europe will lose its strategic autonomy, which guarantees essential goods and services are made available on the European Internal Market. If we continue on this path, the EU will soon become totally dependent on foreign imports with no leverage to implement its sustainability agenda, let alone lead the transition to a circular economy on the international stage.

At present, the EU industry is facing a dire international competition with the industry in China, India and the US working at energy prices of around 10$/MWh. In addition, these competitors are benefitting of sky-high subsidies from their own governments: the rollout of the US $369bln industrial subsidy scheme is just the latest example.

EURATEX Director General, Dirk Vantyghem, believes that “while the EU Industry is under immense, unprecedented pressure, a price cap at 275€/MWh would be meaningless: the European industry will be permanently pushed out on the market. The industry is at the heart of the European way of life and the fundament of our social market economy. The EU must save its industry to save Europe. The moment to act is now.”

More information:
price gap energy crisis Euratex
Source:

EURATEX

31.10.2022

Cinte Techtextil China announces exhibitors for December Edition

From 7 – 9 December 2022, Cinte Techtextil China will welcome visitors sourcing solutions for 12 application areas of technical textiles and nonwovens at the National Exhibition and Convention Center in Shanghai.

A number of countries and regions are represented at the fair’s International Zone, with companies from Austria, Belgium, France, Germany, Hong Kong, Italy, the Netherlands, Spain, Sweden, Switzerland, Taiwan, and the US. Standout international exhibitors include:

From 7 – 9 December 2022, Cinte Techtextil China will welcome visitors sourcing solutions for 12 application areas of technical textiles and nonwovens at the National Exhibition and Convention Center in Shanghai.

A number of countries and regions are represented at the fair’s International Zone, with companies from Austria, Belgium, France, Germany, Hong Kong, Italy, the Netherlands, Spain, Sweden, Switzerland, Taiwan, and the US. Standout international exhibitors include:

  • TESTEX, an international, independent Swiss institute which specialises in the testing and certification of textile and leather products. The organisation is a founding member and official representative of the OEKO-TEX® Association, and will present their certification services at the fairground.
  • Cotton Council International (CCI) is a non-profit trade association that promotes US cotton fibre and manufactured cotton products, with their COTTON USA™ Mark. At this year’s fair they will showcase cotton spunlace fabric, wipes, kitchen tissues, facial masks, cosmetic removers, and more, with their products particularly applicable to Agrotech, Clothtech, Medtech, and Sporttech.
  • Graf + Cie AG is a subsidiary of the Rieter Group, and a leading supplier of clothing for carding and combs for combing machines in the short- and long-staple spinning industry. This year, the Swiss company will showcase stationary flats, and metallic card clothing for roller cards.
  • At the returning German Pavilion, buyers can source sought-after technical textiles and nonwovens that are renowned for their quality. The companies and expertise on display at this pavilion are endorsed by the Federal Republic of Germany, with several exhibitors highlighted below:
  • Brückner Textile Technologies GmbH & Co KG has developed machinery for the textile industry since 1949. Today, the company offers complete line systems for the dry finishing of both woven and knitted fabric, as well as for technical textiles, glass fibres, and floor coverings.
  • Perlon (Zhejiang) Co Ltd is part of a global group of companies that specialises in the manufacture of synthetic filaments, with factories in China, Germany, Poland, and the US. Their products have a diverse range of potential uses, largely categorised in the Agrotech and Indutech application areas.
  • IBENA Textilwerke GmbH produces various functional fabrics for Protech. At the fair, the company will be showcasing insulative, flame retardant (FR) textiles for firefighting and search & rescue services. Developed with DuPont™ aramid material, their FR properties will not diminish after washing or repeated use.

This year’s fair also sees the return of the Taiwan Zone. With support from the Taiwan Nonwoven Fabrics Industry Association, the area will showcase a range of industry leading nonwoven products and services, by brands such as KNH Enterprise, Nan Liu Enterprise, Unique Pretty Ind, and Web-Pro Corporation.

As a world’s largest manufacturer of technical textiles, China is home to a vast array of companies responsible for innovative products. Some domestic exhibitors to look out for are:

  • CTA Hi-Textiles Co Ltd, a high-tech enterprise controlled by China Textile Science Research Institute. In recent years, the company has developed several new textile composite materials, and their products are widely used in sectors such as national defence, policing and public security, medical protection, and engineering and manufacturing.
  • Sateri is one of the world’s largest producers of viscose fibre, with an annual capacity of 1.8 million metric tonnes. At their mills, they make yarn and fibre products applicable to sectors such as beauty, hygiene and personal care, medical, wipes, and protective wear.

To help international buyers stay connected with the Chinese market, Match Plus, the fair’s online business matching platform, will support foreign buyers achieve their sourcing goals despite travel limitations. Further information on Match Plus will be available at a later stage.

The fair’s product categories cover 12 application areas, which comprehensively span a full range of potential uses in modern technical textiles and nonwovens. These categories also cover the entire industry, from upstream technology and raw materials providers to finished fabrics, chemicals and other solutions.

(c) PURE LOOP
07.09.2022

PURE LOOP: High-strength synthetic nonwoven made with a recycled content of 10 percent

Geosynthetics have become an indispensable part of the construction industry. PP nonwovens, for example - mechanically bonded continuous fibres made from specially UV-stabilised polypropylenes - are often used in blanket form as barriers, screens and filters, and their strength extends the service life of construction projects. Whether for road construction, or as barrier on glaciers or against weeds - there are myriad applications.

TenCate Geosynthetics uses the PURE LOOP ISEC evo technology to recycle this type of PP nonwoven. The European company, with locations in Austria, France and the Netherlands, is specialised in the development and production of geotextiles for modern civil engineering applications. The edge trimmings and production rejects generated during manufacturing used to be recycled at the Linz site, but not fed back into the company's own production process.

Geosynthetics have become an indispensable part of the construction industry. PP nonwovens, for example - mechanically bonded continuous fibres made from specially UV-stabilised polypropylenes - are often used in blanket form as barriers, screens and filters, and their strength extends the service life of construction projects. Whether for road construction, or as barrier on glaciers or against weeds - there are myriad applications.

TenCate Geosynthetics uses the PURE LOOP ISEC evo technology to recycle this type of PP nonwoven. The European company, with locations in Austria, France and the Netherlands, is specialised in the development and production of geotextiles for modern civil engineering applications. The edge trimmings and production rejects generated during manufacturing used to be recycled at the Linz site, but not fed back into the company's own production process.

"The demands on us were high," recalls Patrick Wiesinger, project manager at PURE LOOP. "The PP nonwoven is highly tear resistant, which means its a very challenging recycling process. Our ISEC evo machine conserves the quality of the production waste really well during recycling, so we were able to achieve the specified increase in quality for the recyclates."

Another advantage of PURE LOOP technology is the wide range of shapes in which the production scrap can be delivered for processing. "Our ifeed technology with double feed ram system and singleshaft shredder offers the ideal conditions for direct processing of these large rolls - and without the need for prior preparation of the input material by employees before the material is fed into the recycling process", emphasizes Patrick Wiesinger. With the ISEC evo recycling machine TenCate can now manufacture its high-strength PP nonwoven product with a recyclate content of up to 10 percent.

Source:

PURE LOOP, EREMA Group GmbH

Beaulieu International Group
23.08.2022

BIG at EuroGeo7 with geotextile fibres & woven fabrics

Beaulieu International Group invites EuroGeo7 attendees to discover geotextile solutions promoting greater sustainability for future civil engineering projects. Specialists from Beaulieu Fibres International (BFI) and Beaulieu Technical Textiles (BTT) will present high-performance geosynthetics through high tenacity fibres for lightweight, nonwoven geotextiles, and a range of high durability woven geotextile solutions with an environmentally beneficial impact.

Beaulieu International Group invites EuroGeo7 attendees to discover geotextile solutions promoting greater sustainability for future civil engineering projects. Specialists from Beaulieu Fibres International (BFI) and Beaulieu Technical Textiles (BTT) will present high-performance geosynthetics through high tenacity fibres for lightweight, nonwoven geotextiles, and a range of high durability woven geotextile solutions with an environmentally beneficial impact.

“We are delighted to sponsor EuroGeo7 and to be finally on-site, following a two-year postponement of the event. EuroGeo7 is bringing the geotextile community together to further promote and develop geosynthetics in a fast changing global economy striving for growth while reducing its carbon footprint along the supply chain, " comment from Jefrem Jennard, Sales Director Fibres, and Roy Kerckhove, Sales Director Technical Textiles. “Geotextiles provide highly versatile, durable and natural resource-saving alternatives in large infrastructure works, and offer durable protection in erosion control and waste/water management projects. We are continuously developing our fibres and finished engineering textiles with proven sustainability-enhancing benefits to progress product development and customer sustainability goals on fossil carbon reduction, while taking concrete steps to reduce our own environmental footprint.”
 
Sustainability improvement is key to the long-term strategy of Beaulieu International Group, and it is committed to supporting the geotextile industry by targeting and accelerating change and communicating the sustainable performance of its products. The UN Sustainable Development Goals are integrated into its business and are the foundations of the new Route 2030 Sustainability Roadmap.


For manufacturers of nonwoven geotextiles, BFI’s high-tenacity HT8 staple fibres enable customers to achieve nonwovens with high mechanical performance at reduced fibre weight. The HT8 high tenacity fibres are designed in a way that customers can meet the industry durability standards for a longer service lifetime, supporting more sustainable design and resource reduction over time. BTT’s woven geotextiles are amongst the most sustainable in the industry and provide a wide range of functions, including separation, filtration, reinforcement and erosion control.

BFI and BTT have conducted lifecycle assessments to calculate their activities' carbon footprint and solutions and have received external recognition for their ongoing sustainability efforts. For example, in 2022, BFI was awarded a Silver EcoVadis sustainability rating, and BFI and BTT are proud recipients of the Voka Charter for Sustainable Entrepreneurship 2022.

Source:

Beaulieu International Group

15.07.2022

ANDRITZ at CINTE 2022 in China

ANDRITZ will be presenting its innovative nonwovens production solutions at CINTE 2022 in Shanghai, China (September 6–8). ANDRITZ will show its broad product portfolio covering state-of-the-art nonwovens and textile production technologies such as air-through bonding, airlay, needlepunch, spunlace, spunbond, wetlaid/WetlaceTM, converting, textile finishing, recycling, and natural fiber processing.

SUSTAINABILITY IS KEY
ANDRITZ supports nonwovens producers in the move to sustainability with the aim of reducing or eliminating plastic components while maintaining the high quality of the desired product properties. This applies to all types of sustainable wipes, such as flushable, biodegradable, bio-sourced, carded pulp or standard carded wipes. The latest development in this field is the ANDRITZ neXline wetlace CP line, which integrates the carded-pulp (CP) process. This is a fully engineered production line combining the benefits of drylaid and wetlaid technologies to produce a new generation of biodegradable wipes.

ANDRITZ will be presenting its innovative nonwovens production solutions at CINTE 2022 in Shanghai, China (September 6–8). ANDRITZ will show its broad product portfolio covering state-of-the-art nonwovens and textile production technologies such as air-through bonding, airlay, needlepunch, spunlace, spunbond, wetlaid/WetlaceTM, converting, textile finishing, recycling, and natural fiber processing.

SUSTAINABILITY IS KEY
ANDRITZ supports nonwovens producers in the move to sustainability with the aim of reducing or eliminating plastic components while maintaining the high quality of the desired product properties. This applies to all types of sustainable wipes, such as flushable, biodegradable, bio-sourced, carded pulp or standard carded wipes. The latest development in this field is the ANDRITZ neXline wetlace CP line, which integrates the carded-pulp (CP) process. This is a fully engineered production line combining the benefits of drylaid and wetlaid technologies to produce a new generation of biodegradable wipes.

NEXLINE WETLAID AXCESS TARGETS SMALLER AND MEDIUM PRODUCTION VOLUMES
The neXline wetlaid aXcess targets smaller and medium production volumes and has been devised for new and existing lines. The compact line provides an entrance to the growing wetlaid market, with a variety of final applications and options.

ANDRITZ AXCESS DEVELOPED FOR MEDIUM CAPACITIES IN WUXI, CHINA
The aXcess range was specially developed at ANDRITZ (China) Ltd. Wuxi Branch to handle medium capacities. The facility in Wuxi has an experienced platform for production and service specially geared to serve the Asian nonwovens industry. It designs and manufactures cutting-edge lines to complement the ANDRITZ aXcess product range, which includes complete lines and individual machines for air-through bonding, needlepunch and spunlace processes. With the aXcess range, ANDRITZ has developed a hybrid line combining European and Chinese machines, which is the ideal combination to obtain the best added value from each component in the line and be very flexible to accommodate different business cases.

The service organization was set up to provide prompt delivery and excellent customer support, even during the COVID-19 pandemic. A team of technicians and process experts can be deployed quickly to customer sites requiring full-range assistance. The ANDRITZ facilities include a roll service center with state of-the-art grinding equipment and a test stand for various types of rolls.

In addition, our aXcess range manufactured in Europe also offers technologies for spunlaid and wetlaid processes. Increasing production speeds and widths, compact and reliable design, and affordable investment costs are what customers look for in a competitive market environment. To meet these requirements ideally, we recently enhanced our nonwoven calender and dryer ranges.

David Herberg Photo: Adient
David Herberg, Vice President Engineering EMEA at automotive supplier Adient
12.07.2022

David Herberg is a Rising Star 2022

David Herberg, Vice President Engi-neering EMEA at automotive supplier Adient, has been named Rising Star 2022 in the Engineering category by Automotive News Europe magazine.

Every year since 2010, Automotive News Europe has recognized talents in the European automotive industry for their outstanding careers and special achievements in the service of their company and the industry as a whole. To be eligible, candidates must have a minimum of ten years’ experience in the industry, speak at least two languages and be aged 45 years or younger at the time of the nomination.

"The 19 people we are honoring this year are special," said Luca Ciferri, Associate Publisher & Editor of Automotive News Europe. "They’ve made it to the top from a pool of more than 130 candidates, making this year's selection process the most competitive in the history of the award."

David Herberg, Vice President Engi-neering EMEA at automotive supplier Adient, has been named Rising Star 2022 in the Engineering category by Automotive News Europe magazine.

Every year since 2010, Automotive News Europe has recognized talents in the European automotive industry for their outstanding careers and special achievements in the service of their company and the industry as a whole. To be eligible, candidates must have a minimum of ten years’ experience in the industry, speak at least two languages and be aged 45 years or younger at the time of the nomination.

"The 19 people we are honoring this year are special," said Luca Ciferri, Associate Publisher & Editor of Automotive News Europe. "They’ve made it to the top from a pool of more than 130 candidates, making this year's selection process the most competitive in the history of the award."

Herberg, graduate industrial engineer and aged 45, looks back at a career spanning more than ten years at Adient, a leading supplier of seating systems for the automotive industry. After several years at the management consultancy McKinsey and various management positions at Adient as well as its predecessor Johnson Controls, Herberg has been responsible for around 1,200 employees in the development of seat structures, trim and complete seating systems since May 2020.

Source:

Adient

INDA Announces Six New Board Members and Officers (c) INDA
INDA New BOD Members 2022
08.03.2022

INDA Announces Six New Board Members and Officers

  • INDA, the Association of the Nonwoven Fabrics Industry, today announced six new board members and its 2022 slate of officers to guide the success of the nonwovens industry and its members.

Elected by the INDA membership to three-year terms that began on March 1, the new board members bring a high level of diverse expertise and insight to the management of the association as it moves forward with its vibrant growth.

“I am delighted to welcome such a strong group of new board members who bring deep industry knowledge and insights to provide strategic stewardship for our association,” said Dave Rousse, INDA President. “We look forward to working with them to advance INDA’s new value proposition to enhance our industry’s leadership position and deliver greater value to our members.”

The new board members are from global leaders Lenzing Group, Bast Fibre Technologies, Reifenhauser Reicofil, Rockline Industries, Hollingsworth & Vose Company and Principle Business Enterprises.  

  • INDA, the Association of the Nonwoven Fabrics Industry, today announced six new board members and its 2022 slate of officers to guide the success of the nonwovens industry and its members.

Elected by the INDA membership to three-year terms that began on March 1, the new board members bring a high level of diverse expertise and insight to the management of the association as it moves forward with its vibrant growth.

“I am delighted to welcome such a strong group of new board members who bring deep industry knowledge and insights to provide strategic stewardship for our association,” said Dave Rousse, INDA President. “We look forward to working with them to advance INDA’s new value proposition to enhance our industry’s leadership position and deliver greater value to our members.”

The new board members are from global leaders Lenzing Group, Bast Fibre Technologies, Reifenhauser Reicofil, Rockline Industries, Hollingsworth & Vose Company and Principle Business Enterprises.  

INDA also announced Bryan Haynes, Ph.D., R&E Technical Director Kimberly-Clark, has been named Chairman of the Board. Barbara Lawless, Vice President Sales and Marketing, Medical Products, Precision Fabrics Group, Inc. has been elected Vice Chair of Finance, and Richard Altice, President and CEO of NatureWorks, has been appointed to INDA’s Executive Committee.

The new board members are:

  • Jürgen Eizinger, Senior Commercial Director, Nonwovens Business EU/AM/MEA, Lenzing Group

Eizinger has nearly 20 years of fiber industry experience. He has been with the Lenzing Group since 2001 and most recently was Vice President of the Global Nonwoven Business. He has worked at multiple locations around the world and held various commercial, engineering and technical customer services roles.

  • Jim Posa, President and General Manager, Bast Fibre Technologies, Inc.

Posa has 30-plus years of nonwovens experience and has successfully led businesses from startups to some of the largest companies in the nonwovens market. He has developed and implemented strategic business, development, operational and acquisition growth plans. His teams have worked with businesses focused on most of the major end use markets such as hygiene, wipes, filtration, medical and industrial. As a senior executive, Posa has led global businesses at Fiberweb, BP/Amoco, CEO of a Nisseki/Amoco joint venture (ANCI), Lydall, and Nitto America. A long-time INDA supporter, he has previously served on committees and as a Board member.

  • Markus Mueller – Sales Director and Board Member, Reifenhauser Reicofil

Mueller brings to the INDA Board 35 years of experience with Reifenhauser in the nonwovens and film industries. His experience has included roles as PLC Engineer, Commissioning Engineer, Project Manager and Sales Manager. Mueller has extensive knowledge of the global hygiene and medical nonwovens markets. He holds a degree in Electrical Engineering from the Technical University of Cologne.

  • Matt Koele, Director of Global Materials Development, Rockline Industries

Koele is based at Rockline’s headquarters in Sheboygan, WI.  Before joining Rockline in 2012, he has held several business and Research and Development (R&D) leadership positions at SC Johnson and Kimberly-Clark Corporation. An inventor with over 10 patents, Koele is a magna cum laude graduate of Michigan Technological University in Chemical Engineering.

  • Mike Clark, President, Filtration Solutions, Hollingsworth & Vose Company

Clark joined H&V in 2003 and has held numerous leadership positions in the U.S. and Germany. He previously served as the President of the High Efficiency and Specialty Filtration Division from 2009 to 2020.  Before joining H&V, Clark was a strategy consultant for eight years working with Fortune 100 manufacturing companies. He holds a bachelor’s in Mechanical Engineering from Rensselaer Polytechnic Institute.

  • Andrew Stocking, Ph.D., President and CEO, Principle Business Enterprises, Inc. (PBE)

Stocking joined PBE in 2017 after a career in engineering, technology, nonprofits and government. He was named President and COO in 2018, then President and CEO in 2020, becoming the third-generation leader of the family-owned organization. He previously held roles in the private sector and within federal government offices, including the Department of Energy and Congressional Budget Office. He earned a BS in Chemical Engineering and an MS in Civil Engineering from Stanford University, and a Ph.D. in Resource Economics from the University of Maryland.

The 21-member board is comprised of elected Board Officers. One-third of the entire Board is elected each year for a three-year term by a majority vote of INDA’s general membership. INDA’s Executive Committee, empowered to act on behalf of the Board between meetings, consists of the Board Officers plus four appointees.

Source:

INDA, Association of the Nonwoven Fabrics Industry

International technology group ANDRITZ has received an order from Romatex (Pty) Ltd., South Africa, to supply a new batt forming line. © ANDRITZ
ANDRITZ crosslapper PRO 25-90
02.03.2022

ANDRITZ- a new batt forming line for Romatex

  • International technology group ANDRITZ has received an order from Romatex (Pty) Ltd., South Africa, to supply a new batt forming line.

The line will be dedicated to the production of Maliwatt products used in a wide range of applications, including home textiles. Start-up of the line is planned for the fourth quarter of 2022.

ANDRITZ will deliver dedicated batt forming equipment, mixing an aXcess card and an eXcelle crosslapper to achieve the technical characteristics Romatex requires in terms of product quality and line performance. This new stitchbonding line will enable Romatex to better serve the growing customer requirements in terms of availability of high-quality products.

  • International technology group ANDRITZ has received an order from Romatex (Pty) Ltd., South Africa, to supply a new batt forming line.

The line will be dedicated to the production of Maliwatt products used in a wide range of applications, including home textiles. Start-up of the line is planned for the fourth quarter of 2022.

ANDRITZ will deliver dedicated batt forming equipment, mixing an aXcess card and an eXcelle crosslapper to achieve the technical characteristics Romatex requires in terms of product quality and line performance. This new stitchbonding line will enable Romatex to better serve the growing customer requirements in terms of availability of high-quality products.

This will be the third line supplied by ANDRITZ to Romatex in four years. Helmut Höck, General Manager Operations at Romatex, says: “We bought our first line from ANDRITZ in 2017, then another one in 2019. We have been very satisfied with the close collaboration between our companies, the flexibility and reliability of the machines, as well as the excellent service from ANDRITZ over all these years. The experience has been uncomplicated. This has given us the confidence to consider ANDRITZ for a further investment.”

ANDRITZ is one of the global market leaders for supply of nonwoven production technologies, including batt forming equipment for the stitchbonding processes used to make Maliwatt, Malivlies and Multiknit. This segment addresses a variety of applications, including automotive, household, bedding, footwear, wipes, and many others.

Romatex is the leader in Maliwatt stitchbonding in Africa. Its facility is located in Cape Town. One of the company’s key strengths is its product diversification. Today, the company offers a complete range of bed linen, duvets, pillows, and stitchbonded products.

More information:
Andritz nonwovens
Source:

ANDRITZ-GRUPPE

(c) Sitip
21.01.2022

Sitip presents COSMOPOLITAN Fashion-tech fabrics at Milano Unica

Sistema Moda Italia confirms its Innovation Area for the 34th edition of Milano Unica, an area which responds to the growing demand for innovation in products, processes and services able to give specific performances or made with innovative and sustainable systems. And right here we find Sitip’s technical fabrics for clothing, with the COSMOPOLITAN Fashion-tech fabrics collection, modern and comfortable, dedicated to contemporary urbanwear/sportswear style and which perfectly meets the new needs required by the market and by the final consumer: performance and design.

COSMOPOLITAN Fashion-tech is declined into urbanwear through the sartorial technical fabrics that the company has defined Techno Sartorial: a tailoring that combines flawless cuts with exceptional fabric performance.

Sistema Moda Italia confirms its Innovation Area for the 34th edition of Milano Unica, an area which responds to the growing demand for innovation in products, processes and services able to give specific performances or made with innovative and sustainable systems. And right here we find Sitip’s technical fabrics for clothing, with the COSMOPOLITAN Fashion-tech fabrics collection, modern and comfortable, dedicated to contemporary urbanwear/sportswear style and which perfectly meets the new needs required by the market and by the final consumer: performance and design.

COSMOPOLITAN Fashion-tech is declined into urbanwear through the sartorial technical fabrics that the company has defined Techno Sartorial: a tailoring that combines flawless cuts with exceptional fabric performance.

For the production of contemporary urbanwear, thought for the city, Sitip showcases the man’s suit made of jacket+trousers in warp-knit Cosmopolitan Citylife fabric: bi-stretch nylon with UV protection (UPF 50+), quick drying, easy care and skin comfort. Highly performing, breathable, comfortable, insulating and with an exceptional fit: incredible elegance and comfort that enhance the contemporary urbanwear style.

For women, Sitip presents COSMOPOLITAN Fashiontech fabrics dedicated to athleisure, with leggings made - for the summer version - in Cosmopolitan London, a bi-stretch circular knitted fabric, no seethrough, breathable, comfortable on the skin with UV protection (UPF 50+), with easy care and perfect shape retention, and - for the winter version - in Cosmopolitan Paris GZ, a circular knitted fabric raised on the reverse side, with the same properties as the previous one and thermoregulation characteristics.

The Instinct fabric is available in the recycled and raised version NATIVE INSTINCT GZ: a GRS certified thermal fabric made with pre-consumer recycled yarns, bi-stretch, breathable, resistant to pilling, easy care and high comfort, ideal for sporty knitwear and urbanwear part of the NATIVE SUSTAINABLE TEXTILES family, the Sitip fabric collection produced with GRS certified recycled yarns and low environmental impact chemicals with a lower consumption of natural resources , able to respect the environmental and social criteria extended to all the stages of the production chain, including the traceability of raw materials. Sitip also operates in line with international certifications such as OEKO-TEX®, BLUESIGN®, GRS and adheres to the ZDHC gateway, adding to these an ISO 14001 environmental management system, which certifies the company’s commitment to reducing pollution risks.

Source:

Sitip / Valeria Rastrelli

05.11.2021

NCTO Commends House Passage of Infrastructure Package

The National Council of Textile Organizations (NCTO), representing the full spectrum of U.S. textiles from fiber through finished products, issued a statement welcoming House passage of a bipartisan infrastructure bill that will provide billions of dollars in new spending to revitalize the nation’s roads, bridges and railways and help reconstitute a domestic supply chain for face masks, isolation gowns and other personal protective equipment (PPE).

“We commend the House for getting the bipartisan infrastructure bill across the finish line today, and we are pleased the legislation will now go to President Biden for his signature. This is the first step in a long-term strategy that is critically needed to permanently onshore PPE production to ensure our nation is prepared for the next health security crisis,” said NCTO President and CEO Kim Glas. “This infrastructure package will help incentivize the reshoring of PPE production by guaranteeing long-term federal contracts and expanding Berry Amendment rules to more federal agencies’ purchases of PPE products, important priorities of the U.S. textile industry.”

The National Council of Textile Organizations (NCTO), representing the full spectrum of U.S. textiles from fiber through finished products, issued a statement welcoming House passage of a bipartisan infrastructure bill that will provide billions of dollars in new spending to revitalize the nation’s roads, bridges and railways and help reconstitute a domestic supply chain for face masks, isolation gowns and other personal protective equipment (PPE).

“We commend the House for getting the bipartisan infrastructure bill across the finish line today, and we are pleased the legislation will now go to President Biden for his signature. This is the first step in a long-term strategy that is critically needed to permanently onshore PPE production to ensure our nation is prepared for the next health security crisis,” said NCTO President and CEO Kim Glas. “This infrastructure package will help incentivize the reshoring of PPE production by guaranteeing long-term federal contracts and expanding Berry Amendment rules to more federal agencies’ purchases of PPE products, important priorities of the U.S. textile industry.”

NCTO worked with congressional allies to include a version of the Make PPE in America Act, legislation co-sponsored by Senator Rob Portman (R-OH) and Senator Gary Peters (D-MI), in the infrastructure legislative package. The bill ensures all PPE purchased by the Departments of Homeland Security, Health and Human Services and Veterans Affairs are Berry Amendment-compliant (containing 100 percent domestic content); guarantees long-term contracts (a minimum of two years) to U.S. manufacturers; and creates a tiered preference for PPE made in the Western Hemisphere by our free trade partners using U.S. components, after domestic manufacturing capacity has been maximized.