From the Sector

Reset
283 results
FET-200LAB wet spinning system Photo: Fibre Extrusion Technology Limited (FET)
21.11.2022

FET wet spinning system selected for major fibre research programme

Fibre Extrusion Technology Limited (FET) of Leeds, England has installed a FET-200LAB wet spinning system at the University of Manchester which will play a major part in advanced materials research to support sustainable growth and development.

This research programme will be conducted by The Henry Royce Institute, which operates as a hub model at The University of Manchester with spokes at other leading research universities in the UK.

The Henry Royce Institute identifies challenges and stimulates innovation in advanced UK materials research, delivering positive economic and societal impact. In particular, this materials research initiative is focused on supporting and promoting all forms of sustainable growth and development.
These challenges range from biomedical devices through to plastics sustainability and energy-efficient devices; hence supporting key national targets such as the UK’s zero-carbon 2050 target.

Fibre Extrusion Technology Limited (FET) of Leeds, England has installed a FET-200LAB wet spinning system at the University of Manchester which will play a major part in advanced materials research to support sustainable growth and development.

This research programme will be conducted by The Henry Royce Institute, which operates as a hub model at The University of Manchester with spokes at other leading research universities in the UK.

The Henry Royce Institute identifies challenges and stimulates innovation in advanced UK materials research, delivering positive economic and societal impact. In particular, this materials research initiative is focused on supporting and promoting all forms of sustainable growth and development.
These challenges range from biomedical devices through to plastics sustainability and energy-efficient devices; hence supporting key national targets such as the UK’s zero-carbon 2050 target.

FET-200 Series wet spinning systems complement FET’s renowned range of melt spinning equipment. The FET-200LAB is a laboratory scale system, which is especially suitable for the early stages of formulation and process development. It is used for processing new functional textile materials in a variety of solvent and polymer combinations.

In particular, the FET-200LAB will be utilised in trials for a family of fibres made from wood pulp, a sustainable resource rather than the usual fossil fuels. Bio-based polymers are produced from biomass feedstocks such as cellulose and are commonly used in the manufacture of high end apparel. The key to cellulose and other materials like lyocell and viscose is that they can be recycled, treated and fed back into the wet spinning system for repeat manufacture.

Established in 1998, FET is a leading supplier of laboratory and pilot melt spinning systems with installations in over 35 countries and has now successfully processed more than 35 different polymer types in multifilament, monofilament and nonwoven formats.

Source:

DAVID STEAD PROJECT MARKETING LTD

18.11.2022

Monforts at Igatex 2022

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts customers in the regions around the country’s three biggest cities of Karachi, Lahore and Faisalbad include all of the main players in the fields of home textiles and denim production, including Afroze, , Al Karam Artistic Milliners, Azgard-9, Crestex, , Gul Ahmed, Interloop, Liberty Mills, Lucky Textile Mills, Mustaqim, Naveena (NDL), Rajby Industries, Sapphire Finishing, Soorty, Style Textile and US Denim.

These companies rely on established Monforts technologies including Montex stentering equipment, Monfortex sanforizing units and Thermex dyeing ranges. The company’s Matex Eco Applicator minimum application system has also proved a big hit in recent years.

Monforts has also achieved considerable success in Pakistan with its Econtrol®* dyeing system  – an effective and established dyeing process. More than 40 Thermex continuous dyeing ranges have been installed in Pakistan in recent years and operator training on the Econtrol®* process by sophisticated technologists is an additional service.

The Econtrol® pad-dry process has a number of immediate benefits. Compared to the common pad-dry-pad-steam process, no salt is used and no steamer is required for a separate fixation step. Compared to the pad-dry-thermofix process, no urea is used and no smoke or deposits are generated, and unlike with the cold pad batch process, direct feedback of the dyeing results ensures no batching time is necessary and guarantees good reproducibility from the lab to bulk production.

An immediate wash off is also unnecessary, allowing for flexible production planning. The process is suitable for pale to dark shades with very good fastness properties. Also waste water treatment is improved by this technology.

*Econtrol is a registered mark of Dystar Colours Distribution GmbH.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) Robin Inizan – Lucas Pavy Production
Tearing line by ANDRITZ in operation at the Renaissance Textile plant
11.11.2022

Renaissance Textile starts up the first textile recycling line by ANDRITZ in France

Renaissance Textile in Laval, France has successfully started up a complete textile recycling line, delivered, installed, and commissioned by ANDRITZ Laroche, part of the international technology group ANDRITZ.

The ANDRITZ textile recycling equipment enabled Renaissance Textile to become the first French recycling platform dedicated to industrial end-of-life textiles. The project aims to produce new fibers from the collected post-consumer apparel, which will be used to weave new recycled fabrics in the end.

The new 12,000 m² plant is equipped with a complete tearing line whose design is the result of close collaboration between R&D specialists from ANDRITZ Laroche and Renaissance Textile, as well as customized trials carried out jointly by the two parties at the ANDRITZ technical center in Cours, France.

Renaissance Textile in Laval, France has successfully started up a complete textile recycling line, delivered, installed, and commissioned by ANDRITZ Laroche, part of the international technology group ANDRITZ.

The ANDRITZ textile recycling equipment enabled Renaissance Textile to become the first French recycling platform dedicated to industrial end-of-life textiles. The project aims to produce new fibers from the collected post-consumer apparel, which will be used to weave new recycled fabrics in the end.

The new 12,000 m² plant is equipped with a complete tearing line whose design is the result of close collaboration between R&D specialists from ANDRITZ Laroche and Renaissance Textile, as well as customized trials carried out jointly by the two parties at the ANDRITZ technical center in Cours, France.

The new clothing produced based on this type of circular economy model thus reflects the social and sustainability commitments of Renaissance Textile in terms of decarbonizing the textile industry, the fight against global warming, autonomy in raw material sourcing, and promotion of local staffing, particularly for people who have been unemployed for a long time or are seeking to enter the labor market for the first time. By 2025, for example, Renaissance Textile plans to create no less than 110 direct jobs.

Photo Phoenox Textiles
10.11.2022

Sellers Textiles Engineers: New Shearing line for Phoenox

As part of an ongoing investment programme ensuring it remains at the forefront of advanced technology for carpet production, West Yorkshire, UK-headquartered Phoenox Textiles has recently installed a new two-metre-wide shearing line supplied by BTMA member Sellers Textiles Engineers.

Phoenox, which has been family owned since its foundation in 1954, develops original creative flooring design concepts for retail brands. Its products are sold through high street outlets, department stores and volume retailers across Europe and North America, in addition to substantial online and catalogue-driven business. All told, the company’s 24-hour parcel service dispatches some 3.2 million orders every year.

Operating from two manufacturing sites, Phoenox manufactures an annual 1.7 million metres of flooring in the UK. Over a combined area of 1,700,000 square metres, the two plants are equipped for tufting, backcoating, cloth printing and finishing along with automated cutting, sewing and packing.

As part of an ongoing investment programme ensuring it remains at the forefront of advanced technology for carpet production, West Yorkshire, UK-headquartered Phoenox Textiles has recently installed a new two-metre-wide shearing line supplied by BTMA member Sellers Textiles Engineers.

Phoenox, which has been family owned since its foundation in 1954, develops original creative flooring design concepts for retail brands. Its products are sold through high street outlets, department stores and volume retailers across Europe and North America, in addition to substantial online and catalogue-driven business. All told, the company’s 24-hour parcel service dispatches some 3.2 million orders every year.

Operating from two manufacturing sites, Phoenox manufactures an annual 1.7 million metres of flooring in the UK. Over a combined area of 1,700,000 square metres, the two plants are equipped for tufting, backcoating, cloth printing and finishing along with automated cutting, sewing and packing.

In addition to the Sellers shearing line, other recent investments for the UK operations have included three new advanced tufting machines and a high-speed Sellers backcoating line equipped to handle widths of up to two metres and coat at six metres per minute. Washable and dyeable foams and eco-friendly applications in different weights are applied for many product areas.

The company’s state-of-the-art Chromo jet printing process line is meanwhile the only one of its kind in the UK, with its 256 jets making possible designs in up eight colours per pattern. With sustainability very much at the forefront of the company’s approach, Phoenox recycles most of its paste and inks and uses organic options wherever possible, as well as recycled water.

“We operate a piece dye colour cloth programme and can dye nylon and cotton with weights of up to 500kg per load, working with direct, organic, vat and reactive dyes,” says Mosley. “We also offer computerised and weighed commission dyeing. Computerised automated cutting machines and photocell pattern recognition enable us to cut at high speed in most cloth densities. With finishing and sewing though, it’s all about the detail, and our team have years of experience and hand-finish our products on traditional high-speed machines.”

The new Sellers Hybrid Shearing Cylinder can provide a competitive edge for manufacturers which is currently being proven in the field, including at Phoenox. It’s one of a number of new innovations BTMA members are planning to showcase at next year’s ITMA exhibition in Milan.

Source:

AWOL for Phoenox Textiles

Dr. Harald Weber and Thomas Waldmann. Photo: VDMA
from left to right: Dr. Harald Weber and Thomas Waldmann.
08.11.2022

VDMA Textile Machinery Association: Dr Harald Weber succeeds Thomas Waldmann

Dr. Harald Weber will become the new managing director of the VDMA Textile Machinery Association on 1 January 2023. The 44-year-old industrial engineer succeeds Thomas Waldmann, who has held the position since 1991 and will retire at the end of the year.

After completing his doctorate at the Technical University of Darmstadt and working as a lecturer at the University of Applied Sciences Mittelhessen (THM), Dr. Weber joined the VDMA in 2011. Since then, he has been responsible for the topics of technology and innovation in the Plastics and Rubber Machinery Association.

Dr. Janpeter Horn, Chairman of the VDMA Textile Machinery Association and Managing Director of August Herzog Maschinenfabrik, commented on the change of personnel: "From his previous work in the plastics industry, Dr. Weber has profound knowledge and experience in topics that are also gaining in importance in textile machinery manufacturing. Examples include recycling and the circular economy, as well as digitalisation and especially the communication standard OPC UA."

Dr. Harald Weber will become the new managing director of the VDMA Textile Machinery Association on 1 January 2023. The 44-year-old industrial engineer succeeds Thomas Waldmann, who has held the position since 1991 and will retire at the end of the year.

After completing his doctorate at the Technical University of Darmstadt and working as a lecturer at the University of Applied Sciences Mittelhessen (THM), Dr. Weber joined the VDMA in 2011. Since then, he has been responsible for the topics of technology and innovation in the Plastics and Rubber Machinery Association.

Dr. Janpeter Horn, Chairman of the VDMA Textile Machinery Association and Managing Director of August Herzog Maschinenfabrik, commented on the change of personnel: "From his previous work in the plastics industry, Dr. Weber has profound knowledge and experience in topics that are also gaining in importance in textile machinery manufacturing. Examples include recycling and the circular economy, as well as digitalisation and especially the communication standard OPC UA."

Dr. Horn added: "We combine our warm welcome to Dr. Weber with a big thank you to Thomas Waldmann. 30 years as managing director at the Textile Machinery Association also stand for constantly changing framework conditions. Mr. Waldmann has always had his finger on the pulse of the industry and, together with his team, has represented the special interests of the member companies: From technology policy to challenges of market access to the leading trade fair ITMA and the European association CEMATEX. ITMA 2007 in Munich was certainly a highlight. The executive board of the association wishes Mr. Waldmann all the best for the new phase of his life that is now beginning."

Source:

VDMA e. V.
Textile Machinery

(c) JIAM, Messe Frankfurt Japan Ltd
07.11.2022

JIAM 2022 OSAKA taking place after a six year break

JIAM 2022 OSAKA, organised by the Japan Sewing Machinery Manufacturers Association (JASMA), will soon be held at INTEX OSAKA from 30 November – 3 December 2022. Under the theme of “It all connects at JIAM – the forefront of technology and master craftsmanship”, the 12th edition brings together leading sewing machine suppliers and apparel manufacturers, making it a must-attend event for textile professionals. In this era of change, an international platform to facilitate business and information exchange is essential. The 2022 edition will showcase apparel manufacturing solutions catered to each and every need, combining high-level skillsets and time-tested knowledge with the latest modern-day technology.

JIAM 2022 OSAKA, organised by the Japan Sewing Machinery Manufacturers Association (JASMA), will soon be held at INTEX OSAKA from 30 November – 3 December 2022. Under the theme of “It all connects at JIAM – the forefront of technology and master craftsmanship”, the 12th edition brings together leading sewing machine suppliers and apparel manufacturers, making it a must-attend event for textile professionals. In this era of change, an international platform to facilitate business and information exchange is essential. The 2022 edition will showcase apparel manufacturing solutions catered to each and every need, combining high-level skillsets and time-tested knowledge with the latest modern-day technology.

As of October, 144 exhibitors from 10 countries and regions (China, Greece, Germany, Hong Kong, India, Italy, Singapore, Taiwan and Thailand) have signed up for JIAM 2022 OSAKA to showcase their latest products and services. Of these, 39 companies (21 domestic, 18 overseas) will be joining the fair for the first time. In addition, two pavilions from Germany (VDMA; Mechanical Engineering Industry Association) and Taiwan (TSMA; Taiwan Sewing Machinery Association) will bring even more product diversity to the show floor. The previous edition of JIAM OSAKA in 2016 welcomed 258 exhibitors from 15 countries and regions as well as 15,257 visitors from 72 countries and regions, mainly from Bangladesh, China, India, Korea, Taiwan, Sri Lanka, and Vietnam.

A wide variety of special seminars
11 special organiser seminars will not only provide relevant industry knowledge, but also offer practical skills for daily work:

  • Manufacturing industry and digital technology
    Mr Atsushi Yasuda, Manager of Ministry of Economy, Trade and Industry Manufacturing Industries Bureau,Industrial Machinery Division
  • Skills training seminar
    1. Twist Jacket (Lapel) pattern and matching sewing (front and shoulder seams)
    2. Shoulder keeper (prevent shoulder collapse) cherish a piece of clothing
    Mr Susumu Inarida, Emeritus Professor of Bunka Fashion Graduate University (BFGU) / Specially Appointed Committee Member of Japan Modelist Associate / Contemporary Master Craftsman Certified by the Ministry of Health, Labor and Welfare
  • "Mottainai!" sustainable initiatives from Osaka!
    Common points between Senshu Towl and OSAKA KABAN and the future
    Mr Eiji Shinoda, President of Shinoda cCorp
    Mr Kenji Fukuroya, Representative Employee of Fukuroya Joint Company etc.
  • About the sustainable fashion community “NewMake”- Upcycling initiatives in collaboration with brands
    Mr Tac Hosokawa, CEO of Story & Co.
  • Win - win strategy on underwear sewing, viewpoint of BISEI SANGYO Co., LTD
    Mr Toru Miyawaki, Managing Executive Officer of BISEI SANGYO Co.,LTD / Chairman of Hikoneseni Cooperative

Home Sewing Machine Zone
Catering to the B2C market, the Home Sewing Machine Zone, will feature major domestic household sewing machine suppliers. To promote the joy of sewing, a special workshop will be organised by Brother Industries Ltd, Janome Corp, JUKI Corp and JASMA covering topics such as the use of upcycled materials. As part of JIAM 2022 OSAKA’s sustainable development goals, visitors will be taught to sew “cup sleeves” using discarded items and materials from the DIY brand WHTATNOT. Attendees will also learn about upcycling, the process of upgrading unwanted items into new products that are useful. Another highlight will be the awards for JASMA’s “42th Home Sewing Competition for Elementary, Middle, and High School Students”.

Source:

JIAM, Messe Frankfurt Japan Ltd / Messe Frankfurt (HK) Limited

04.11.2022

Rieter publishes Investor Update 2022

  • Sales of CHF 366.8 million in the third quarter, CHF 987.4 million after nine months
  • Order intake of CHF 226.4 million in the third quarter, CHF 1 095.8 million after nine months
  • Order backlog of around CHF 2 000 million as of September 30, 2022
  • Precautionary measures taken against potential energy crisis in Europe
  • Financing of a Professorship for Artificial Intelligence
  • Rieter site sales process on schedule
  • Outlook 2022

Rieter recorded a significant increase in sales in the third quarter of 2022, reaching a level of CHF 366.8 million (2021: CHF 257.3 million). The measures introduced to increase sales and profitability in the second half of 2022 are taking effect and will continue to be implemented in a systematic manner. These include a close cooperation with key suppliers, the development of alternative solutions to eliminate material shortages, the enforcement of price increases, and the improvement of the margin quality of the order backlog.

  • Sales of CHF 366.8 million in the third quarter, CHF 987.4 million after nine months
  • Order intake of CHF 226.4 million in the third quarter, CHF 1 095.8 million after nine months
  • Order backlog of around CHF 2 000 million as of September 30, 2022
  • Precautionary measures taken against potential energy crisis in Europe
  • Financing of a Professorship for Artificial Intelligence
  • Rieter site sales process on schedule
  • Outlook 2022

Rieter recorded a significant increase in sales in the third quarter of 2022, reaching a level of CHF 366.8 million (2021: CHF 257.3 million). The measures introduced to increase sales and profitability in the second half of 2022 are taking effect and will continue to be implemented in a systematic manner. These include a close cooperation with key suppliers, the development of alternative solutions to eliminate material shortages, the enforcement of price increases, and the improvement of the margin quality of the order backlog.

The order intake of CHF 226.4 million in the third quarter of 2022 reflects the expected normalization of demand for new equipment compared to the record year of 2021, which was characterized by catch-up effects and the regional shift in demand. In addition, the well-known uncertainties and risks and the continuing extremely long delivery times at key manufacturers had a dampening effect on demand. Due to the slowdown in capacity utilization in the spinning mills, demand for consumables, wear & tear and spare parts also declined in the third quarter of 2022. Major orders continued to be recorded from Turkey, Uzbekistan, and China.

Rieter has a high order backlog of around CHF 2 000 million as of September 30, 2022 (September 30, 2021: CHF 1 562 million), which will guarantee capacity utilization in all three business groups until well into 2023 or rather 2024. The cancellation rate in the reporting period was around 5% of the order backlog.

Outlook 2022
Rieter anticipates weakened demand for new systems in the coming months. The demand for consumables, wear & tear and spare parts will depend on the capacity utilization of spinning mills in the months ahead.

For the full year 2022, Rieter expects sales of around CHF 1 400 million. The realization of sales revenue from the order backlog continues to be associated with risks in relation to the well-known uncertainties.

Despite significantly higher sales compared to the prior-year period, Rieter expects EBIT and net result for 2022 to be below the previous year’s level. This is due to the considerable increases in the cost of materials and logistics, additional costs for compensation of material shortages as well as expenses in connection with the acquisition in the years 2021/2022.

More information:
Rieter financial year 2022
Source:

Rieter Management AG

(c) EFI
31.10.2022

EFI sells 300th VUTEk FabriVU Printer

Orbus Exhibit & Display Group® has continued its substantial and longstanding relationship with digital print technology provider Electronics For Imaging, Inc., choosing the premium-quality capabilities of the EFI™ VUTEk® FabriVU® 340+ soft signage printer to meet surging demand for dye-sublimation soft signage graphics. The new printer now running at Orbus’s Las Vegas facility marks an important milestone for EFI, as it is the 300th EFI VUTEk FabriVU printer installed worldwide.

Orbus is North America’s top trade manufacturer of soft signage and flag graphics for tradeshow exhibits, promotional displays, experiential retail and corporate interiors. The company is one of the largest users of EFI soft signage printers worldwide. The newly installed FabriVU 340+ model joins two additional FabriVU printers at Orbus Las Vegas. The company has its fourth FabriVU printer at its headquarters facility, along with a pair of high-volume EFI industrial printers used exclusively for dye-sublimation production.

Orbus Exhibit & Display Group® has continued its substantial and longstanding relationship with digital print technology provider Electronics For Imaging, Inc., choosing the premium-quality capabilities of the EFI™ VUTEk® FabriVU® 340+ soft signage printer to meet surging demand for dye-sublimation soft signage graphics. The new printer now running at Orbus’s Las Vegas facility marks an important milestone for EFI, as it is the 300th EFI VUTEk FabriVU printer installed worldwide.

Orbus is North America’s top trade manufacturer of soft signage and flag graphics for tradeshow exhibits, promotional displays, experiential retail and corporate interiors. The company is one of the largest users of EFI soft signage printers worldwide. The newly installed FabriVU 340+ model joins two additional FabriVU printers at Orbus Las Vegas. The company has its fourth FabriVU printer at its headquarters facility, along with a pair of high-volume EFI industrial printers used exclusively for dye-sublimation production.

The upgraded performance comes courtesy of the VUTEk FabriVU 340+ printer’s new, eight-printhead, CMYK x 2 array, along with new electronics for reliable and consistent premium-quality output of exhibit graphics, backlit graphics, retail fixture wraps, front lit graphics, block-out banners and fabric interior decor. A flag printing kit on the printer easily handles porous media in high-penetration applications by collecting inks without touching the rear side of the media.
 
As with all VUTEk FabriVU printers, it prints both transfer paper and direct-to-fabric.

Source:

EFI

(c) Rieter
Autoconer X6
31.10.2022

Rieter at India ITME 2022

Rieter is presenting the latest innovations in its systems, components and services at the upcoming India ITME 2022 in Uttar Pradesh (India), taking place from December 8 – 13, 2022.

Autoconer X6
The automatic winding machine Autoconer X6 completes the Rieter ring and compact-spinning systems. The machine serves as the final quality assurance in the ring and compact-spinning process and is key to the performance of the subsequent process stages. The Multilink system with Multilot offers maximum flexibility to handle a different type of yarn.

The latest splicer generation OZ1 and OZ2 provides an optimum splice quality based on an open prism. With only two prisms spinning mills can splice the entire spectrum of cotton yarns as well as blends. They are also used for the splicing of cotton-based elastic core yarns in combination with the Elastosplicer. The splice zone exhibits an impressive elasticity in the fabric.

Rieter is presenting the latest innovations in its systems, components and services at the upcoming India ITME 2022 in Uttar Pradesh (India), taking place from December 8 – 13, 2022.

Autoconer X6
The automatic winding machine Autoconer X6 completes the Rieter ring and compact-spinning systems. The machine serves as the final quality assurance in the ring and compact-spinning process and is key to the performance of the subsequent process stages. The Multilink system with Multilot offers maximum flexibility to handle a different type of yarn.

The latest splicer generation OZ1 and OZ2 provides an optimum splice quality based on an open prism. With only two prisms spinning mills can splice the entire spectrum of cotton yarns as well as blends. They are also used for the splicing of cotton-based elastic core yarns in combination with the Elastosplicer. The splice zone exhibits an impressive elasticity in the fabric.

Compacting Solutions
The Rieter compacting devices include the COMPACTapron, COMPACTeasy and COMPACTdrum. Spinning mills can change quickly between ring and compact yarn and offer customers a broader product range.

Recycling Expertise from Rotor to Ring
Rieter offers solutions for the integration of recycled raw material into yarn production to help close the textile loop and make fashion more circular. Both rotor and ring yarns can be produced with a considerable amount of mechanically recycled fibers.

ESSENTIALorder
Based on existing customer information, the webshop ESSENTIALorder visualizes which Rieter machines andn systems are available inside each spinning mill. It therefore offers a personalized shopping experience and facilitates order management, enabling spinning mills to optimize their internal stock levels.

ROBOspin
The piecing robot ROBOspin reduces personnel requirements in the ring spinning section by 50%. The robot also attains productivity increases thanks to higher spindle speeds at equal or higher efficiency.

SSM NEO-FD
SSM is presenting NEO-FD, the assembly-winding machine for precision wound packages for twisting. It meets all requirements for efficient production. The machine features the auto-doffing option and the online back-pressure system for low and high package densities.

Temco CoolFlow Disc
Temco’s CoolFlow texturing discs offer longer lifetime thanks to a brand-new geometry and the latest polyurethane technology. The texturing discs now generate a disc surface that operates at a lower temperature, resulting in slower ageing and abrasion. Further benefits are more stable yarn quality, higher productivity, and an overall process cost reduction.

Photo: Reifenhäuser
26.10.2022

Reifenhäuser Extrusion Systems and maku AG cooperate

  • Strategic partnership for automation system in the field of slot dies and coextrusion adapters

Reifenhäuser Extrusion Systems (RES) - the Reifenhäuser Group's business unit specializing in extrusion components - announces a strategic partnership with maku AG at K 2022, the world's largest plastics trade fair. The aim of the cooperation is the joint marketing and further development of the automation system designed by maku for coextrusion adapters and slot dies.

  • Strategic partnership for automation system in the field of slot dies and coextrusion adapters

Reifenhäuser Extrusion Systems (RES) - the Reifenhäuser Group's business unit specializing in extrusion components - announces a strategic partnership with maku AG at K 2022, the world's largest plastics trade fair. The aim of the cooperation is the joint marketing and further development of the automation system designed by maku for coextrusion adapters and slot dies.

The so-called PAM system (precise, autonomous, mechatronic) is available immediately and exclusively as an automation option for new Reifenhäuser dies and adapters, as well as for aftermarket dies across all manufacturers. PAM enables producers in the field of flat film and sheet production as well as extrusion coating to precisely control the entire hot part (coextrusion adapter and die) via the line's control panel. This is significantly faster and more accurate than conventional control by hand or expansion bolt automation. It enables faster start-up of good production, higher output with lower energy consumption, and thus significantly improved overall equipment efficiency (OEE). The decisive advantage lies in the use of motorized manual adjustment bolts that replace conventional thermal expansion bolts. Reifenhäuser presented the system for the first time at the K 2022.

Source:

Reifenhäuser GmbH & Co. KG Maschinenfabrik
 

Texaid / Texcircle
26.10.2022

Swiss Textile Recycling Project TEXCIRLCE

After two years of joint collaboration and research the Swiss Textile Recycling Project “Texcircle” comes to an end. Partners and stakeholders have worked on the vision of a textile cluster where materials flow in circular loops. The goal of the project was to develop high-quality yarns and products incorporating such a large amount of recycled textiles as possible. In the end, several product prototypes from carpets, socks, and curtains to pullovers, padding and accessories have been developed with at least 50 % recycled fiber up to 80 % recycled fibers and yarns.

Europe has a waste problem of 7.5 million waste of which only 30-35 % is collected and less than 1 % of the textile and clothing worldwide is recycled into textiles and clothing again. It is as well found that around 80 % of the impact of a textile product lies in the design.

After two years of joint collaboration and research the Swiss Textile Recycling Project “Texcircle” comes to an end. Partners and stakeholders have worked on the vision of a textile cluster where materials flow in circular loops. The goal of the project was to develop high-quality yarns and products incorporating such a large amount of recycled textiles as possible. In the end, several product prototypes from carpets, socks, and curtains to pullovers, padding and accessories have been developed with at least 50 % recycled fiber up to 80 % recycled fibers and yarns.

Europe has a waste problem of 7.5 million waste of which only 30-35 % is collected and less than 1 % of the textile and clothing worldwide is recycled into textiles and clothing again. It is as well found that around 80 % of the impact of a textile product lies in the design.

Together with the design research expertise of the Lucerne University of Applied sciences and arts, the spinning expertise of Rieter and the sorting and collection expertise of Texaid, systems should be created where products of high quality can be produced of recycled fiber. On board were the expertise of further Cluster partners of Brands, Retailers, and the public sector to see how a joint Cluster and system coukld be established.

The Project Texcircle and cluster is led by the Lucerne University of Applied Sciences and Arts – Art  & Design, and in collaboration with Coop, Rieter, Jacob Rohner AG, Ruckstuhl AG, TEXAID as well as workfashion.com ag. Furthermore, Bundesamt für Zivildienst ZIVI, NIKIN AG, and Tiger Liz Textiles are supporting the project. The project is funded by Innosuisse.

Furthermore, collaboration partners from all over Europe contributed to the project to enable these prototypes and systems.

Through joint developments from the design, the collecting, sorting trials, tearing, and spinning trials until the actual production trials and product testing. The partners were able to recycle 2.5 Tons of pre-and post-consumer textile waste into product prototypes with a promising commercial interest. From socks, west, and pullovers to non-woven felts and accessories to carpets and curtains. Through our 2 years of collaboration, the teamcame across several hurdles in the textile recycling value chain which could be tackled. This was a proof of concept that a circular system is possible and the industry now has to enable this at full scale.

Source:

Texaid / Texcircle

Photo: Monforts
The new seven chamber Montex TwinAir stenter range with Montex®Coat coating at the plant.
26.10.2022

Dolinschek: Compression stockings in a variety of colours

The identification of profitable new niche markets has been central to the success and continuous expansion of Germany’s Dolinschek, a leading knitting, dyeing and finishing specialist, located in Burladingen in Baden-Württemberg.

“There is so much more to textiles than just clothing,” says Theo Dolinschek, who runs the company with his brother Erwin. “We handle many different technical materials such as automotive components, geotextiles and wallcoverings, but also those for more unusual applications such as inlays for extractor hoods, cut protection fabrics and even wool felts which are employed as insulation on wind turbines.

“We have also recently started to produce compression stockings in a variety of colours, because not everyone wants them black, beige or skin coloured. The most important product areas for us now are in sportswear, corsetry and lingerie, as well as orthopedic and medical products, workwear and protective clothing, but in addition, many other technical applications.”

The identification of profitable new niche markets has been central to the success and continuous expansion of Germany’s Dolinschek, a leading knitting, dyeing and finishing specialist, located in Burladingen in Baden-Württemberg.

“There is so much more to textiles than just clothing,” says Theo Dolinschek, who runs the company with his brother Erwin. “We handle many different technical materials such as automotive components, geotextiles and wallcoverings, but also those for more unusual applications such as inlays for extractor hoods, cut protection fabrics and even wool felts which are employed as insulation on wind turbines.

“We have also recently started to produce compression stockings in a variety of colours, because not everyone wants them black, beige or skin coloured. The most important product areas for us now are in sportswear, corsetry and lingerie, as well as orthopedic and medical products, workwear and protective clothing, but in addition, many other technical applications.”

The Dolinschek brothers moved their business to the historic site of the former Ambrosius Heim textile company in Burladingen in 2001 in order to expand. At the time, the company – founded by their father in 1980 as a textile wholesaler before moving into dyeing – employed just 13 people. Within a year, the company had bought additional space at the site.

Now, with Theo in charge of technology and sales, and Erwin responsible for production, the company employs almost 100 people and operates on an integrated site of 35,000 square metres.

In 2005, a laminating department was established by the company and since 2012 investment in knitting machines has been ongoing.

“The further we went into vertical integration, the more of our own products we were able to position on the market and so we were also able to make ourselves more independent,” says Theo. “We have continued to develop and today we can produce high-quality fabrics for many fields, with 42 knitting machines, 36 dyeing machines, three stenter frames and many other production and processing machines.”

Dolinschek has also developed its own proprietary TMG dyeing machines which have subsequently been successfully sold to many other companies all over the world. There are currently 11 of these machines  in operation at the Burladingen site and around 45 installed at other companies.

For finishing technology, however, the company relies on Monforts, and has installed a new seven chamber Montex TwinAir stenter range with a Montex®Coat coating unit in knife execution, enabling the coating of dimensionally stable knitted fabrics with polyurethane or acrylate. Another unique feature is the Teflon-coated (non-stick) transportation belt through the system.

The Montex line is also equipped with integrated heat recovery and exhaust gas purification to ensure the most resource-efficient processing available on the market. The exhaust air goes from the Monforts heat recovery system into an existing air/water heat recovery system and then into an electrostatic precipitator.

Highly-intuitive Monforts Qualitex visualisation software allows all machine functions and process parameters to be assessed and controlled easily.

 

More information:
Dolinschek Monforts
Source:

AWOL Media

Freudenberg´s gas diffusion layer production Photo: Freudenberg´s gas diffusion layer production.
20.10.2022

Freudenberg supplies gas diffusion layers for fuel cell stacks

Freudenberg Performance Materials (Freudenberg) has concluded a high-volume, multi-year contract with a global automotive tier one supplier to supply high-performance gas diffusion layers for the stacks forming the core of the fuel cell systems produced by the leading automotive supplier. Global target applications are mid-sized and heavy commercial vehicles as well as buses. Freudenberg is supporting the customer’s global fuel cell activities, thereby also accelerating the breakthrough of mass-produced fuel cell stacks.

Fuel cell technology is an important element of a successful energy transition. Gas diffusion layers play a key role in this context: they are indispensable for the functioning of a fuel cell and have a significant impact on the performance of a fuel cell stack.

Freudenberg Performance Materials (Freudenberg) has concluded a high-volume, multi-year contract with a global automotive tier one supplier to supply high-performance gas diffusion layers for the stacks forming the core of the fuel cell systems produced by the leading automotive supplier. Global target applications are mid-sized and heavy commercial vehicles as well as buses. Freudenberg is supporting the customer’s global fuel cell activities, thereby also accelerating the breakthrough of mass-produced fuel cell stacks.

Fuel cell technology is an important element of a successful energy transition. Gas diffusion layers play a key role in this context: they are indispensable for the functioning of a fuel cell and have a significant impact on the performance of a fuel cell stack.

A fuel cell converts the chemical energy of hydrogen and atmospheric oxygen into electricity. Functionally-optimized gas diffusion layers made of carbon-fiber based nonwoven are installed on both sides of a catalyst-coated membrane positioned in the middle of the fuel cell. The gas diffusion layers distribute hydrogen and oxygen evenly to the membrane and remove the electricity, heat and water generated by the CO2-free chemical reaction. They also protect the sensitive membrane and are optimized to suit the bipolar plate. A fuel cell stack is made up of several individual fuel cells.

Freudenberg already has more than 20 years of unique expertise in the development and production of gas diffusion layers for fuel cell applications in the mobility sector and for porous transport layers used in electrolyzers. Freudenberg is currently expanding its production capacity at its Weinheim headquarters by installing additional lines. Further investments are on the verge of implementation.

Photo: Andritz
14.10.2022

ANDRITZ to install Metris predictive maintenance system for spunlace line

International technology group ANDRITZ has received an order from Welspun Advanced Materials, India, to supply a Metris predictive maintenance system for its spunlace production line at the Telangana plant. This will be the first Metris solutions system to be installed in a spunlace line in India.

The integrated Metris platform developed by ANDRITZ uses smart sensors as an energy self-sufficient and seamless support solution to monitor machine conditions continuously, even in areas that are difficult to access. As a result, analysis of the data collected allows clients to pinpoint every possible issue upfront and helps to enhance line performance.

The Metris predictive maintenance system will enable Welspun Advanced Materials to increase its operating efficiency by:

  • avoiding unexpected line shutdowns, thus increasing performance
  • enabling easy operation along the entire line
  • optimizing maintenance organization and planning


This order follows the start-up of the newly installed, complete high-speed ANDRITZ spunlace line at the Telangana plant.

International technology group ANDRITZ has received an order from Welspun Advanced Materials, India, to supply a Metris predictive maintenance system for its spunlace production line at the Telangana plant. This will be the first Metris solutions system to be installed in a spunlace line in India.

The integrated Metris platform developed by ANDRITZ uses smart sensors as an energy self-sufficient and seamless support solution to monitor machine conditions continuously, even in areas that are difficult to access. As a result, analysis of the data collected allows clients to pinpoint every possible issue upfront and helps to enhance line performance.

The Metris predictive maintenance system will enable Welspun Advanced Materials to increase its operating efficiency by:

  • avoiding unexpected line shutdowns, thus increasing performance
  • enabling easy operation along the entire line
  • optimizing maintenance organization and planning


This order follows the start-up of the newly installed, complete high-speed ANDRITZ spunlace line at the Telangana plant.

Foto: (c) Starlinger & Co Gesellschaft m.b.H.
11.10.2022

Starlinger PET recycling lines in India: Bottle-to-fibre and bottle-to-bottle

Ganesha Ecopet Private Limited, a subsidiary of Indian PET recycling pioneer Ganesha Ecosphere Ltd., has recently opened its new Warangal facility under the brand name Go Rewise where it produces rPET for filament yarns and fibres, as well as for food-grade packaging.  

The company has installed two Starlinger PET recycling lines in its facility in Warangal, Telangana state. Ganesha Ecopet plans to supply the produced rPET granulates under its newly introduced brand enterprise Go Rewise. Launched under the umbrella of one of India's rPET industry leaders, Go Rewise is committed to supplying highest quality rPET products that are produced in a resource-efficient process.
One Starlinger recycling line, a recoSTAR PET 165 H-VAC, processes washed PET bottle flakes for the Go Rewise polyester filament yarn applications and reaches an output of approx. 14,000 tons per year. With the second Starlinger recycling line, Ganesha is producing food-grade rPET resins.

Ganesha Ecopet Private Limited, a subsidiary of Indian PET recycling pioneer Ganesha Ecosphere Ltd., has recently opened its new Warangal facility under the brand name Go Rewise where it produces rPET for filament yarns and fibres, as well as for food-grade packaging.  

The company has installed two Starlinger PET recycling lines in its facility in Warangal, Telangana state. Ganesha Ecopet plans to supply the produced rPET granulates under its newly introduced brand enterprise Go Rewise. Launched under the umbrella of one of India's rPET industry leaders, Go Rewise is committed to supplying highest quality rPET products that are produced in a resource-efficient process.
One Starlinger recycling line, a recoSTAR PET 165 H-VAC, processes washed PET bottle flakes for the Go Rewise polyester filament yarn applications and reaches an output of approx. 14,000 tons per year. With the second Starlinger recycling line, Ganesha is producing food-grade rPET resins.

Ganesha Ecosphere looks back on 30 years of experience in the PET recycling business and can be considered a role model regarding sustainable business activities. Founded in 1987, the company started out as a yarn processing facility. It was among the first companies in India to start reprocessing PET waste to manufacture recycled polyester staple fibre (RPSF) and recycled polyester spun yarns (RPSY) in 1994. By today, the group has established a large network of over 300 scrap vendors located across the country and operates four factories in India - two in Uttar Pradesh, one in Uttarakhand, and the recently opened one in Telangana. It also recently operationalised its first factory outside India in Nepal. With over 500 customers and exports to more than 18 countries, the company ranks among the largest rpet producers in India with 130,000 tonnes per year and currently recycles around 16 - 18 % of India's total PET waste.

Source:

Starlinger & Co Gesellschaft m.b.H.

(c) BTMA
The James Heal AirPro air permeability tester
11.10.2022

BTMA: Testing equipment manufacturer James Heal celebrates 150th anniversary

Long-standing BTMA member James Heal is celebrating its 150th anniversary this year, the company’s formation dating back to 1872, when it was listed as an oil and tallow merchant and mill furnisher in Yorkshire, UK.

Today, as a testing equipment manufacturer for textiles and nonwovens, James Heal continues to expand its range, with a focus on making testing simple – most notably with the introduction of its Performance Testing collection of instruments, most recently the AirPro and HydroView systems.

AirPro
The new James Heal AirPro air permeability tester is used to test the resistance of the flow of air through woven, knitted and nonwoven textiles. Its software offers flexibility with standards and  comprehensive reporting options and different test head sizes are available, making it suitable for a range of applications and standards

Long-standing BTMA member James Heal is celebrating its 150th anniversary this year, the company’s formation dating back to 1872, when it was listed as an oil and tallow merchant and mill furnisher in Yorkshire, UK.

Today, as a testing equipment manufacturer for textiles and nonwovens, James Heal continues to expand its range, with a focus on making testing simple – most notably with the introduction of its Performance Testing collection of instruments, most recently the AirPro and HydroView systems.

AirPro
The new James Heal AirPro air permeability tester is used to test the resistance of the flow of air through woven, knitted and nonwoven textiles. Its software offers flexibility with standards and  comprehensive reporting options and different test head sizes are available, making it suitable for a range of applications and standards

HydroView
The HydroView hydrostatic head tester is meanwhile designed to measure the penetration of water in materials which have an end use that requires water resistance, such as those in the medical, geotextiles and nonwovens sectors. It is also proving essential in the testing of end-use applications for technical textiles, such as in protective gloves, diving dry suits and winter sports apparel, to fishing waders, roofing, tenting, ground sheets and more.

Photo: Sellers Textile Engineers
Hybrid Shearing Cylinder
10.10.2022

The Hybrid Shear by Sellers Textile Engineers

BTMA member Sellers Textile Engineers is marking its 110th anniversary this year with the introduction of a new concept in carpet shearing, as the essential final step in ensuring tuft uniformity and ‘just new’ freshness in finished carpet rolls.

The company has for many years offered two options in the construction of its shearing cylinders – the first, namely the ‘strap-on’, incorporates spiral blades bolted to the cylinder body and the second, known as the ‘caulked-in’, includes spirals which are fixed very securely in a machined groove within the machine.

The new Sellers’ Hybrid Shearing Cylinder combines the benefits of both, resulting in an improved cut and finer finish, in addition to longer repeatable finishing and increased rigidity.

BTMA member Sellers Textile Engineers is marking its 110th anniversary this year with the introduction of a new concept in carpet shearing, as the essential final step in ensuring tuft uniformity and ‘just new’ freshness in finished carpet rolls.

The company has for many years offered two options in the construction of its shearing cylinders – the first, namely the ‘strap-on’, incorporates spiral blades bolted to the cylinder body and the second, known as the ‘caulked-in’, includes spirals which are fixed very securely in a machined groove within the machine.

The new Sellers’ Hybrid Shearing Cylinder combines the benefits of both, resulting in an improved cut and finer finish, in addition to longer repeatable finishing and increased rigidity.

“The Hybrid Shearing Cylinder has all the advantages of the ‘strap-on’ spiral blade to provide a sharper and cleaner cut, along with enhanced rigidity which significantly lengthens the intervals between the necessary regrinding of the blade,” explains Sellers Director Neil Miller. “We currently have six Hybrid Shearing Cylinders operating in the field and the earliest, which has been installed in both No1 Head position, where the majority of the shearing operation and heaviest cut is performed, and also in No3 Head, where the sharper cutting angle has resulted in a much improved surface quality.”

Sellers shearing machines have led the field in carpet finishing for many decades, enabling the leading manufacturers to stay competitive by enabling the highest quality of finish to be achieved economically and efficiently.

The latest advanced features of these machines include a load cell tension control drive system, an automated touchscreen for easy operator control and fault diagnosis, an enhanced cleaning system including cylinder and blade separation and fully controllable pivoting beds. Further options include thickness monitoring, seam detection and metal detection systems.

“The Hybrid Shearing Cylinder will become standard on our latest machines and also be made available for retrofitting, to provide significant benefits to our existing users,” says Miller. “All of our equipment is designed, manufactured, assembled and tested at our plant in the UK, and as one of the few remaining European engineering companies to make all of our components in-house – with now over a century of accumulated know-how – flexibility in design allows our finishing solutions to be targeted to specific customers and their product requirements. Aligned to this is a lead in process control systems which ensure the accurate control, reliability and repeatability of the processing parameters on all of our machines.”

Sellers remains committed to providing complete finishing solutions for all carpet, tile and artificial grass products. Its range includes machines for tufted secondary backing, both conventional, powder and extrusion lamination, Wilton and Axminster products, artificial grass and foam lines, coating lines for bitumen, PVC, PU and other polymers, as well as shearing for all carpet products.

Ongoing developments on the company’s coating and drying lines have resulted in improved guiding and product tension control as well as dryer efficiency, reducing heat loss and optimising energy use. These include a re-design of the fan pressure boxes and impingement nozzles to increase airflow efficiency, modulating gas burners and introducing easy clean, accessible filters.

In addition, the proven dual zone system has been enhanced, giving a temperature differential of up to 80°C between top and bottom zones. Dryers can be heated by either gas or steam and operation and access have been simplified with controls via touchscreen and PLC.

An extensive range of ancillary equipment is available to provide maximum flexibility to cover product requirements, for both new processing lines and as upgrades to existing equipment.

“Carpet manufacturing is now based on well-established, tried and trusted processes and it’s rare for new innovations to be introduced into this sector,” says Jason Kent, CEO of the British Textile Machinery Association. “The new Sellers Hybrid Shearing Cylinder can provide a competitive edge for manufacturers which is currently being proven in the field. It’s one of a number of new innovations the company is planning to showcase at next year’s ITMA exhibition in Milan.”

(c) Mimaki Europe B.V.
07.10.2022

Mimaki announces Third Virtual Global Innovation Days Event

Mimaki announce their third Global Innovation Days (19th – 21st October 2022). This collaborative virtual experience unites Mimaki’s regional offices to discuss trends across the different markets and the American, Asian, and European regions operated in by Mimaki, through a series of live and pre-recorded demonstrations, webinars, and round-table discussions. The programme of events will be led by experts from Mimaki Europe, Japan, USA and Australia.

With a focus on addressing the queries and requirements across the many facets of the print industry, the event will see collaborations with the likes of FESPA, from whom spokespeople will be attending to discuss the latest trends and innovations identified at FESPA this year, as well as a look ahead to next year’s event and what people can expect to see.

Mimaki announce their third Global Innovation Days (19th – 21st October 2022). This collaborative virtual experience unites Mimaki’s regional offices to discuss trends across the different markets and the American, Asian, and European regions operated in by Mimaki, through a series of live and pre-recorded demonstrations, webinars, and round-table discussions. The programme of events will be led by experts from Mimaki Europe, Japan, USA and Australia.

With a focus on addressing the queries and requirements across the many facets of the print industry, the event will see collaborations with the likes of FESPA, from whom spokespeople will be attending to discuss the latest trends and innovations identified at FESPA this year, as well as a look ahead to next year’s event and what people can expect to see.

Attendees will also have the opportunity to further explore the latest additions to Mimaki’s product portfolio, with demonstrations of the technologies and the applications that they are able to create coming live from the Mimaki showroom in Amsterdam. The 330 series, including the JV330-160, CJV330-160 and TS330-1600, will be showcased, as well as the full-colour capabilities of the 3DUJ-2207 3D printer, and Mimaki’s latest flatbed printer, the JFX600-2513, which boasts speeds thrice superior to that of its predecessor. Another highlight of the event will be a discussion held with leading print media and software vendors, to examine the current market trends from outside of the manufacturing perspective.

Source:

Mimaki Europe B.V.

06.10.2022

Rieter and the Johann Jacob Rieter Foundation Sponsor Professorship for AI

Together with the Johann Jacob Rieter Foundation, the Rieter Group is supporting a new Endowed Professorship for Industrial Artificial Intelligence (AI) at the ZHAW School of Engineering. The Professorship is dedicated to teaching and research in the field of industrial applications of Artificial Intelligence and will be announced later this year.

The new Endowed Professorship will be established at the Center for Artificial Intelligence (CAI) of the ZHAW in Winterthur. It will focus, in particular, on the application of machine learning methods and knowledge-based systems in connection with processes in production and service.

For Rieter, the commitment is related to the implementation of its technology leadership strategy. The contribution of the Johann Jacob Rieter Foundation to sponsoring the Professorship is in line with the Winterthur Cluster Initiative. The increasing digitalization of production processes opens up new perspectives for Winterthur as a business location.

Together with the Johann Jacob Rieter Foundation, the Rieter Group is supporting a new Endowed Professorship for Industrial Artificial Intelligence (AI) at the ZHAW School of Engineering. The Professorship is dedicated to teaching and research in the field of industrial applications of Artificial Intelligence and will be announced later this year.

The new Endowed Professorship will be established at the Center for Artificial Intelligence (CAI) of the ZHAW in Winterthur. It will focus, in particular, on the application of machine learning methods and knowledge-based systems in connection with processes in production and service.

For Rieter, the commitment is related to the implementation of its technology leadership strategy. The contribution of the Johann Jacob Rieter Foundation to sponsoring the Professorship is in line with the Winterthur Cluster Initiative. The increasing digitalization of production processes opens up new perspectives for Winterthur as a business location.

Building Expertise in the Field of Industrial AI
The Endowed Professorship will serve to build expertise in the field of Industrial AI and will oversee a group that will focus on teaching and research pertaining to trustworthy machine learning. This involves, for example, the deployment of artificial intelligence with the aim of optimizing production processes in relation to the use of raw materials and energy, and making expert knowledge more readily available.

In addition to research, for the purpose of knowledge transfer, the new professorship will also be active in teaching, in the bachelor's degree programs in Computer Science and in Data Science, in the Master of Science in Engineering, and in continuing education.

The annual commitment of CHF 300 000 over a period of six years will be financed equally by the Rieter Group and the Johann Jacob Rieter Foundation.
“The use of artificial intelligence in industry is becoming increasingly important, especially with regard to the potential of data for evaluation and control of complex processes. The support of the Johann Jacob Rieter Foundation and the Rieter Group will allow us to further expand AI research in the field of industrial applications,” explains Prof. Dr. Dirk Wilhelm, Director of the ZHAW School of Engineering.

“The use of Artificial Intelligence will make a significant contribution to automation and process optimization, and thereby advance sustainability in the textile industry. This makes it an important element of the leading technology that Rieter offers,” emphasizes Rieter CEO Dr. Norbert Klapper.

“The Smart Machines cluster is growing in importance,” says Thomas Anwander, member of the Foundation Board, and adds: “The Endowed Professorship for Industrial AI at the ZHAW aims to promote Winterthur as a technology location by pooling locally available strengths in mechanical engineering and Industry 4.0.”

(c) BRÜCKNER
The project team of BRÜCKNER and HEATHCOAT in BRÜCKNER’s Technology Centre in Leonberg
04.10.2022

BRÜCKNER: New finishing line for British company HEATHCOAT FABRICS

HEATHCOAT FABRICS partnered again with BRÜCKNER Textile Technologies and their sales partner ADVANCED DYEING SOLUTIONS to install a finishing line for industrial textiles. HEATHCOAT FABRICS specializes in the production of technical textiles in the fields of texturising, weaving and warp knitting as well as dyeing and finishing. The prroducts are manufactured for use in the automotive, healthcare, defence, and aerospace industries

Mrs. Regina Brückner, CEO and owner of the BRÜCKNER Group stated: "To meet the complex re-quirements of HEATHCOAT is not easy because of the great variety of technical textiles produced. Our line has to finish light as well as heavy articles, so the design, control and the whole line layout have to be flexible, functional and still easy to operate. Fortunately, the team at HEATHCOAT FABRICS is very innovative and open-minded, and together we worked hard to develop the right technology and han-dling. We are very happy that we could convince this customer, whom we appreciate very much, with the productivity of our line and of course with our technological know-how."

HEATHCOAT FABRICS partnered again with BRÜCKNER Textile Technologies and their sales partner ADVANCED DYEING SOLUTIONS to install a finishing line for industrial textiles. HEATHCOAT FABRICS specializes in the production of technical textiles in the fields of texturising, weaving and warp knitting as well as dyeing and finishing. The prroducts are manufactured for use in the automotive, healthcare, defence, and aerospace industries

Mrs. Regina Brückner, CEO and owner of the BRÜCKNER Group stated: "To meet the complex re-quirements of HEATHCOAT is not easy because of the great variety of technical textiles produced. Our line has to finish light as well as heavy articles, so the design, control and the whole line layout have to be flexible, functional and still easy to operate. Fortunately, the team at HEATHCOAT FABRICS is very innovative and open-minded, and together we worked hard to develop the right technology and han-dling. We are very happy that we could convince this customer, whom we appreciate very much, with the productivity of our line and of course with our technological know-how."

The direct gas heated BRÜCKNER POWER-FRAME stenter with its staggered heating source arrangement every half zone provides best available temperature consistency across the length and the width of the stenter. The unit is equipped with a low-lub, horizontally returning combined pin / clip chain and several fabric paths, especially designed for the different fabrics being processed. Together with HEATHCOAT FABRICS technologists, the BRÜCKNER design team developed a special delivery end of the stenter with different edge trimming and slitting possibilities. Depending on the kind of products, the fabrics can be batched on large diameter A-frames, wound on cardboard tubes or plaited into trolleys.

Source:

Brückner Trockentechnik GmbH & Co. KG