From the Sector

Reset
266 results
Herr Dr.-Ing. Moniruddoza Md. Ashir vom ITM wurde am 12. Oktober 2021 für seine Dissertation "Entwicklung von neuartigen textilbasierten adaptiven Faserkunststoffverbunden mit Formgedächtnislegierungen“ mit dem Innovationspreis des Industrieclubs Sachsen 2020 ausgezeichnet. © Juergen Loesel
Herr Dr. Ashir (2.v.re.) zur Preisverleihung des Innovationspreises des Industrieclubs Sachsen 2020 gemeinsam mit Frau B. Deutsch (Geschäftsführerin Industrieclub Sachsen e.V.), Herr Prof. Dr. Ch. Cherif (Direktor des ITM), Frau Prof. U. Staudinger (Rektorin der TUD) und Herrn Dr. G. Bruntsch (Präsident Industrieclub Sachsen e.V.); v.l.n.r.
27.10.2021

Wissenschaftler vom ITM der TU Dresden mit dem Innovationspreis des Industrieclubs Sachsen geehrt

  • Herr Dr.-Ing. Moniruddoza Md. Ashir vom ITM wurde am 12. Oktober 2021 für seine Dissertation "Entwicklung von neuartigen textilbasierten adaptiven Faserkunststoffverbunden mit Formgedächtnislegierungen“ mit dem Innovationspreis des Industrieclubs Sachsen 2020 ausgezeichnet.
  • Der Preis ist mit 5.000 EUR dotiert und wird jährlich an einen Absolventen der TU Dresden verliehen.

Die Entscheidung zur Vergabe des Innovationspreises des Industrieclubs Sachsen 2020 erfolgte im Sommer 2021 durch ein Preisgericht. Die Verleihung des Innovationspreises erfolgte im Rahmen einer Veranstaltung des Industrieclubs Sachsen im Schloss Eckberg in Dresden am 12. Oktober 2021.

  • Herr Dr.-Ing. Moniruddoza Md. Ashir vom ITM wurde am 12. Oktober 2021 für seine Dissertation "Entwicklung von neuartigen textilbasierten adaptiven Faserkunststoffverbunden mit Formgedächtnislegierungen“ mit dem Innovationspreis des Industrieclubs Sachsen 2020 ausgezeichnet.
  • Der Preis ist mit 5.000 EUR dotiert und wird jährlich an einen Absolventen der TU Dresden verliehen.

Die Entscheidung zur Vergabe des Innovationspreises des Industrieclubs Sachsen 2020 erfolgte im Sommer 2021 durch ein Preisgericht. Die Verleihung des Innovationspreises erfolgte im Rahmen einer Veranstaltung des Industrieclubs Sachsen im Schloss Eckberg in Dresden am 12. Oktober 2021.

In der Dissertation werden alternative Ansätze auf Basis von innovativen textilbasierten adaptiven Faserkunststoffverbunden (FKV) mit strukturintegrierten Formgedächtnislegierungen konzipiert, umgesetzt, erprobt und im Vergleich mit konventionellen technischen Lösungen evaluiert. Daher galt es, eine Vielzahl bisher ungelöster konzeptioneller sowie textil- und materialspezifischer Fragestellungen zu bearbeiten und tiefgreifend zu analysieren. Hierzu zählen die Entwicklung neuartiger Ansätze und technologischer Lösungen sowohl zur reproduzierbaren Einstellung einer anforderungsgerechten Grenzschicht zwischen der Formgedächtnislegierung in Drahtform sowie dem umgebenden Faserverbundwerkstoff, als auch zur vollautomatischen Integration des textilverarbeitbaren Aktors in die Verstärkungsstruktur. Weitere Zielstellungen bestanden in der Ermittlung von Struktur-Funktionseigenschaftsbeziehungen, dem Nachweis der funktionalen Langzeitstabilität sowie der Konzeptionierung und Erprobung von industrierelevanten Funktionsdemonstratoren. Hier wurden adaptive FVK als bionisch inspirierter Flug-, Nachgiebigkeits-, Greif-, Spann-, gezielter Flüssigkeitssteuerungs-, Wisch- und Fortbewegungsmechanismus konzipiert. Diese Demonstratoren repräsentieren alle wesentlichen Funktionalitäten der adaptiven FVK-Kinematik und lassen sich leicht auf andere industrielle Anwendungsbereiche übertragen, wie z. B. die Flugzeug-, Automobil-, Medizin-, Soft-Robotik-, Bau- oder Industrietechnikbranche.

Die Forschungs- und Entwicklungsarbeiten erfolgten in enger Zusammenarbeit mit der Industrie, wie z. B. thoenes Dichtungstechnik GmbH und Elbe Flugzeugwerke GmbH und werden zukünftig am ITM intensiv fortgesetzt. Die neu entwickelte Technologie und Strukturen werden dem Leichtbau insbesondere als Knotenelemente für Rahmentragwerke im Fahrzeugbau, in der Luft- und Raumfahrt, im Maschinenbau sowie auch in der Architektur neue Impulse verleihen. Gegenwärtig wird forschungsseitig die Anwendung dieser Strukturen für medizinische Bereiche, insbesondere orthopädische oder prothetische Hilfsmittel, vorangetrieben.

Source:

Technische Universität Dresden

(c) RadiciGroup
25.10.2021

RadiciGroup: Sustainable Personal Protective Equipment at A+A

RadiciGroup is exhibiting at the A+A trade fair, an international event focusing on safety solutions for the workplace, to be held in Dusseldorf, Germany, from 26 to 29 October. This international show gives RadiciGroup the opportunity to present its latest developments in personal protective equipment (PPE) for industrial use, including coveralls, gowns, caps, full hoods, shoe covers and boots.

This international show gives RadiciGroup the opportunity to present its latest developments in  personal protective equipment (PPE) for industrial use, including coveralls, gowns, caps, full hoods, shoe covers and boots. These products are part of a new line, Radipeople, a trade name identifying the new protective workwear sold by RadiciGroup: end products of a traceable supply chain, in which special attention is paid to the choice of raw materials and the quality of the final products offered the market.

RadiciGroup is exhibiting at the A+A trade fair, an international event focusing on safety solutions for the workplace, to be held in Dusseldorf, Germany, from 26 to 29 October. This international show gives RadiciGroup the opportunity to present its latest developments in personal protective equipment (PPE) for industrial use, including coveralls, gowns, caps, full hoods, shoe covers and boots.

This international show gives RadiciGroup the opportunity to present its latest developments in  personal protective equipment (PPE) for industrial use, including coveralls, gowns, caps, full hoods, shoe covers and boots. These products are part of a new line, Radipeople, a trade name identifying the new protective workwear sold by RadiciGroup: end products of a traceable supply chain, in which special attention is paid to the choice of raw materials and the quality of the final products offered the market.

At RadiciGroup, care for the health and safety of people is one of the pillars of the Group's sustainability strategy, combined with a strong commitment to safeguarding the environment. Radipeople Eco, the first protective coverall with 100% end-of-life recyclability is proof of such commitment. All parts of Radipeople Eco: the fabric, lamination, zipper and thread are made of the same material, 100% polypropylene. Furthermore, the Group’s offering includes garments made with Respunsible®, a spundbond obtained from recycled polypropylene or materials certified under the ISCC Plus scheme.

Thanks to their versatility and technical characteristics, the nonwoven solutions proposed by RadiciGroup are suitable for many industrial sectors, including oil and gas, utilities, construction, food, automotive painting and shipbuilding, maintenance, agriculture, laboratories, microprocessor manufacturing and the pharmaceutical and chemical industries.

Radipeople personal protective equipment delivers excellent protection against external agents (liquids, splashes, jets, particles and sprays), high protection against biological hazards and infectious agents, and high robustness and lightness to optimize protection, on the one hand, and comfort, on the other. All Radipeople protective equipment is made of fully traceable materials, manufactured by a totally Italian production chain involving hundreds of workers, and sold in packaging designed with an ecodesign approach, that is, fully recyclable minimized packaging.

Source:

RadiciGroup

DiloGroup at Techtextil India (c) DiloGroup
3D-Lofter
20.10.2021

DiloGroup at Techtextil India

  • DiloGroup looks forward to participating in the Techtextil India show 2021.

DiloGroup offers tailor-made production systems from one supplier and will inform at this forum in the German pavillon about its portfolio and the latest equipment developments from fibre opening to the finished felt.

A new, simplified elliptical needle beam drive makes Hyperpunch technology also attractive for standard application. Hyperpunch HαV allows a more uniform stitch distribution in the preneedling process especially in combination with the new needle pattern 6000X. In a complete needling line this felt homogenization process can be improved further by using the new needle pattern 8000X which is a milestone in the needle pattern development process and results in endproduct surfaces with low markings over a wide range of advances/stroke.

  • DiloGroup looks forward to participating in the Techtextil India show 2021.

DiloGroup offers tailor-made production systems from one supplier and will inform at this forum in the German pavillon about its portfolio and the latest equipment developments from fibre opening to the finished felt.

A new, simplified elliptical needle beam drive makes Hyperpunch technology also attractive for standard application. Hyperpunch HαV allows a more uniform stitch distribution in the preneedling process especially in combination with the new needle pattern 6000X. In a complete needling line this felt homogenization process can be improved further by using the new needle pattern 8000X which is a milestone in the needle pattern development process and results in endproduct surfaces with low markings over a wide range of advances/stroke.

The “3D-Lofter” which was first presented during ITMA 2019 in Barcelona offers a wider range of nonwovens applications by exploring the third dimension. A series of single web forming units which work according to the aerodynamic web forming principle deliver defined fibre masses in varied patterns on a base needlefelt. A stress oriented production of technical formed parts resulting in fibre savings or patterned DI-LOUR or DI-LOOP felts are two examples for this technology which explores new application areas for needlefelts.

The 3D-Lofter technology may also be used “inverted” for filling up bad spots in web mats and thus achieves a better homogeneity of e. g. spunlace, thermobond or airlay products. The DiloLine 4.0 concept offer I4.0 modules which not only support the user but also facilitate quality control and maintenance by a maximum data transparency in production and control of operation. The Dilo solutions “Smart Start” for a fully automatic start of the production line or “DI-LOWATT” for energy savings are accompanied by Siemens solutions which can be selected via App or Data Cloud “MindSphere”.

With more than 370 installations delivered to the nonwovens industry worldwide, DiloGroup has the necessary know-how and the complete equipment portfolio to engineer the perfect production line for any product specification. The efficiency of Dilo production lines is the result of long-term research work and experience. Apart from machines for needling technology we offer in cooperation with partner companies also production lines including thermobonding and hydroentangling components.

Source:

Oskar Dilo Maschinenfabrik KG

(c) Trevira GmbH
19.10.2021

Indorama at Index 2021 with Sustainability Portfolio

The Hygiene Fibers Group of Indorama Ventures (IVL) came together at the Index Show to present an all-inclusive range of recycled and biodegradable solutions for Hygiene Fiber and Nonwoven applications.

The combination of polymers, technologies, processes and global reach supported by the Hygiene Fibers Group – one of three business segments that make up Indorama Ventures – positions it within the Hygiene industry to meet increasingly challenging market demand for innovative sustainable solutions within the hygiene sector. Across the six brands and companies that make up Hygiene Fibers Group – Auriga, Avgol, FiberVisions, Indorama Asia, Trevira and Wellman International – sustainability and supporting customers to achieve circular objectives is integral to all efforts and fundamental to the ethos of the Hygiene business segment.

The Hygiene Fibers Group of Indorama Ventures (IVL) came together at the Index Show to present an all-inclusive range of recycled and biodegradable solutions for Hygiene Fiber and Nonwoven applications.

The combination of polymers, technologies, processes and global reach supported by the Hygiene Fibers Group – one of three business segments that make up Indorama Ventures – positions it within the Hygiene industry to meet increasingly challenging market demand for innovative sustainable solutions within the hygiene sector. Across the six brands and companies that make up Hygiene Fibers Group – Auriga, Avgol, FiberVisions, Indorama Asia, Trevira and Wellman International – sustainability and supporting customers to achieve circular objectives is integral to all efforts and fundamental to the ethos of the Hygiene business segment.

At the Index Show, the Hygiene Fibers Group launched CiCLO®, a textile technology which allows polyester and other synthetic materials to biodegrade like natural materials do in wastewater treatment plant sludge, sea water and landfill conditions, reducing synthetic microfiber pollution generated during washing, and minimizing plastic accumulation in landfills caused by discarded textiles.

In line with the company’s commitment to support customers with high performance products, while also reducing the impact on the environment, several of the  Hygiene Fibers brands, including Wellman International, Trevira GMBH and Auriga, have been working closely over the last 12 months with the IAM team and the CiCLO® technology. Developments have focused on PET and rPET staple fiber and filament sustainable solutions for applications where recycling is particularly challenging, such as Hygiene, Home Textiles and Automotive applications.

Strengthening the profile of biodegradable offerings within the Hygiene Fibers Group’s sustainability portfolio, Trevira introduced a new range of bicomponent fibres based on PLA and PBS (polybutylene succinate) at the Index show. Both biopolymers offer an exceptional technological opportunity in terms of environmental care and sustainability, while delivering optimum performance. Equally to PLA, PBS is recyclable and up to 100% biodegradable under industrial conditions.

Efforts towards supporting customers to achieve circular objectives are a priority within the Hygiene Fibers Group. This is reflected in the recycled fibers expertise deployed across the segment. Four Hygiene Fibers Group brands, IVL Asia, Auriga, Trevira and Wellman International offer an extensive range of 100% recycled, accredited PET fibers, across a multitude of fiber and nonwovens applications.

The development and evolution of sustainable technologies is central to activity across IVL’s Hygiene Fibers Group, with particular focus on sustainable polyolefin solutions. FiberVisions and ES-FIBERVISIONS, leading Polyolefin mono and bico fiber brands and sister company Avgol, have partnered with UK-based Polymateria to commercially harness the innovative ‘biotransformation’ technology pioneered by Polymateria. The patented technology alters the properties of polyolefins to make them biodegradable in a natural process.  Other polyolefin sustainable innovations within the Hygiene Fibers Group were featured at Index include biosurfactant and biocolourant developments being undertaken by the Avgol team with FiberVisons progressing sustainable design solutions, including lightweight, high performance, reduced carbon solutions.

Source:

Trevira GmbH, Indorama Ventures

12.10.2021

DSM to showcase armor solutions made with Dyneema® at Milipol Paris 2021

DSM, the inventor and manufacturer of Dyneema®, will be exhibiting at one of the leading events for homeland security and safety, Milipol Paris 2021, from October 19-22.

The performance characteristics of Dyneema® make it ideal for a variety of applications, including soft and hard armor ballistics to protect against today’s advanced and emerging threats. In addition, Dyneema® combines next-generation fiber technology and unidirectional engineering to deliver armor solutions with unmatched ballistic stopping power in a lightweight and flexible composite.

By implementing Dyneema®, body armor manufacturers are able to use less material in the development of their ballistic vests, plates and helmets. This leads to weight savings upwards of 30 percent when compared to competitive materials, without impacting ballistic performance. The lightweight construction of armor made with Dyneema® also mitigates injuries associated with the cumulative effects of daily armor use – while improving situational awareness, as well as cognitive and tactical performance.

DSM, the inventor and manufacturer of Dyneema®, will be exhibiting at one of the leading events for homeland security and safety, Milipol Paris 2021, from October 19-22.

The performance characteristics of Dyneema® make it ideal for a variety of applications, including soft and hard armor ballistics to protect against today’s advanced and emerging threats. In addition, Dyneema® combines next-generation fiber technology and unidirectional engineering to deliver armor solutions with unmatched ballistic stopping power in a lightweight and flexible composite.

By implementing Dyneema®, body armor manufacturers are able to use less material in the development of their ballistic vests, plates and helmets. This leads to weight savings upwards of 30 percent when compared to competitive materials, without impacting ballistic performance. The lightweight construction of armor made with Dyneema® also mitigates injuries associated with the cumulative effects of daily armor use – while improving situational awareness, as well as cognitive and tactical performance.

While decreasing the load on the wearer, Dyneema® is simultaneously able to reduce the impact of material manufacturing on our planet. In line with DSM’s commitment to protect people and the environment they live in, we have developed the first-ever bio-based ultra-high molecular weight polyethylene fiber and unidirectional (UD) material. Bio-based Dyneema® boasts the same exact performance as conventional Dyneema® with a carbon footprint that is 90 percent lower than generic HMPE.

Source:

DSM Protective Materials / EMG

07.10.2021

Lenzing rated “sustainability champion” by MSCI ESG

The Lenzing Group, leading supplier of wood-based specialty fibers, has received further recognition of its performance in sustainability. The prestigious rating agency MSCI has upgraded its rating for the Lenzing Group from “A” to “AA” as at September 2021. As a result, Lenzing ranks among the top 6 percent of companies rated in its peer group.

The upgrade to the MSCI ESG rating will also lead to a reduction in Lenzing’s interest expense. Lenzing placed a bonded loan worth EUR 500 mn in November 2019, which is linked to its sustainability performance. In accordance with its commitment under the bonded loan placement, the company will donate the full amount of the interest expense saved thanks to the rating revision to a project it supports.

The rating agency MSCI, whose rating determines the interest rate for the bonded loan, cited the company's ambitious climate targets, its approach to promoting a circular economy and exceptionally good governance structure as the main reasons for the upgrade.

The Lenzing Group, leading supplier of wood-based specialty fibers, has received further recognition of its performance in sustainability. The prestigious rating agency MSCI has upgraded its rating for the Lenzing Group from “A” to “AA” as at September 2021. As a result, Lenzing ranks among the top 6 percent of companies rated in its peer group.

The upgrade to the MSCI ESG rating will also lead to a reduction in Lenzing’s interest expense. Lenzing placed a bonded loan worth EUR 500 mn in November 2019, which is linked to its sustainability performance. In accordance with its commitment under the bonded loan placement, the company will donate the full amount of the interest expense saved thanks to the rating revision to a project it supports.

The rating agency MSCI, whose rating determines the interest rate for the bonded loan, cited the company's ambitious climate targets, its approach to promoting a circular economy and exceptionally good governance structure as the main reasons for the upgrade.

More information:
Lenzing Sustainability
Source:

Lenzing AG

01.10.2021

Archroma celebrates 8 Years of creating positive impact

Archroma celebrates 8 years of leading the way to a sustainable world, with innovations and solutions aimed at creating added value sustainable for its partners, consumers and the planet.

Archroma came to life on 1st October 2013 from textile, paper and emulsions businesses acquired from Clariant by SK Capital Partners.
Building on decades of commitment to developing safer eco-friendlier chemistry, Archroma has become in the past 8 years a prominent name for more sustainable colors and performance, collaborating with leading brands such as Primark, G-Star, Patagonia, Esprit and more.

Archroma has introduced innovations, such as the EarthColors® made from non-edible plant waste from the food and herbal industry, Denisol® Pure, an indigo for aniline-free* denim, aniline being a category 2 carcinogen substance, and Smartrepel®, a PFC-free* water repellent solution. The company is also about to launch a new plant-based softener.

Archroma celebrates 8 years of leading the way to a sustainable world, with innovations and solutions aimed at creating added value sustainable for its partners, consumers and the planet.

Archroma came to life on 1st October 2013 from textile, paper and emulsions businesses acquired from Clariant by SK Capital Partners.
Building on decades of commitment to developing safer eco-friendlier chemistry, Archroma has become in the past 8 years a prominent name for more sustainable colors and performance, collaborating with leading brands such as Primark, G-Star, Patagonia, Esprit and more.

Archroma has introduced innovations, such as the EarthColors® made from non-edible plant waste from the food and herbal industry, Denisol® Pure, an indigo for aniline-free* denim, aniline being a category 2 carcinogen substance, and Smartrepel®, a PFC-free* water repellent solution. The company is also about to launch a new plant-based softener.

The company started to develop holistic solutions designed to bring innovation and performance, whilst reducing the impacts on water, energy and other natural resources. The savings generated by these 70+ system solutions are demonstrated by Archroma's proprietary ONE WAY Impact Calculator, a tool launched in 2012 and continuously upgraded to simulate and optimize the footprint of application processes.

Archroma also recently launched CASUAL X SMART, a sulfur dyeing system for trendy wash-down effects to make clothes that look smart at home and at work. The colors won't fade in the washing cycle, and the application process allows resource savings of up to 33% water, 21% energy and 35% chemical usage compared to a benchmark reactive & pigment garment dyeing.

With ONE WAY, a brand can calculate how much impact their current production and the Archroma Way collection will have on water, energy, chemical, raw material or CO2 footprint.

(c) Archroma
23.09.2021

Archroma: Online regulatory & compliance platform

  • Instant access to ecotoxicological and regulatory information and certificates for Archroma specialty chemical products
  • Faster decision-making and time-to-market for manufacturers, brands and retailers in the textile, paper, packaging, paint, and construction industries

Archroma, a global leader in specialty chemicals towards sustainable solutions, announced the launch of The Safe Edge, an online platform for instant access to product related regulatory & compliance certificates and information.

With continuously growing public awareness around the social, health and ecological impacts of human and business activities, the need for transparency and traceability in supply chains has become essential.

Time to market is equally critical, and manufacturers, brands and retailers need access to reliable information in real time.

  • Instant access to ecotoxicological and regulatory information and certificates for Archroma specialty chemical products
  • Faster decision-making and time-to-market for manufacturers, brands and retailers in the textile, paper, packaging, paint, and construction industries

Archroma, a global leader in specialty chemicals towards sustainable solutions, announced the launch of The Safe Edge, an online platform for instant access to product related regulatory & compliance certificates and information.

With continuously growing public awareness around the social, health and ecological impacts of human and business activities, the need for transparency and traceability in supply chains has become essential.

Time to market is equally critical, and manufacturers, brands and retailers need access to reliable information in real time.

The Safe Edge platform has been designed with that in mind: It allows brands, retailers and manufacturers of textile, fashion, packaging, paper, paints, to verify with just a few clicks the regulatory & compliance status of Archroma products, including regulations, ecotoxicological information & certifications, and brand requirements.

The Safe Edge covers standards, regulations and information such as air emission factors, animal origin, halal, kosher, plant origin, food contact, Blue Angel, bluesign®, Cradle-to-Cradle, chemical inventories, Composability EN 13432, conflict minerals, EU Flower/Ecolabel, GOTS, CONEG, ISEGA, Nordic Swan, Oekotex® Standard 100, California Prop 65, REACH, RoHS (Restriction of Hazardous Substance), Screened Chemistry, SDS, SVHC (Substance of Very High Concern), VOC (US), ZDHC (Zero Discharge Hazardous Chemicals), and brand standards (like Coats A&F MRSL, Decathlon RSL 2020, Jack Wolfskin RSL and The List IV by Inditex.

With the launch of The Safe Edge, Archroma continues to assert its leading role in driving sustainability in its industries, in line with its commitment to the principles of “The Archroma Way to a Sustainable World: safe, efficient, enhanced, it’s our nature”. The “Safe” principle in particular is at the core of the Archroma approach to sustainability, with the deeply rooted goal to protect people and the planet with products that are safe to use, and safe to wear.

The Safe Edge is already accessible for manufacturers, brands and retailers in Europe and Asia, and will be launched in North America in September 2021, and in Latin America by the end of the year.

More information:
Archroma online platform
Source:

Archroma

Bemberg™ by Asahi Kasei at Filo to unveil its smart DNA story that meet contemporary consumer needs (c) Bemberg™
Waxewul proposal using Bemberg™.
15.09.2021

Bemberg™ by Asahi Kasei at Filo to unveil its smart DNA story that meet contemporary consumer needs

  • FILO, 29th-30th September 2021, booth C5

Bemberg™ by Asahi Kasei has been invited to showcase at Filo fair, the international exhibition of orthogonal weaving yarns for clothing and furnishings, circular knitwear and technical textiles, in a new special area, a dedicated open space reserved to sustainable fibers that will allow visitors to discover all their production cycle and performances, in full relax and transparency.

Bemberg™, an exceptional fiber made from the smart-tech transformation of cotton linters pre-consumer materials and converted through a traceable and transparent closed loop process, will brings to Filo its history, experience, know-how and market partnerships to prove its versatility and design-driven look and touch Last but not least we are talking about a true circular economy-oriented ingredient, with certified sustainable performance: Bemberg™ is biodegradable and compostable material as verified by the INNOVHUB 3rd party test and it has GRS (Global Reycled Standard) certification from Textile Exchange proving recycling authenticity.

  • FILO, 29th-30th September 2021, booth C5

Bemberg™ by Asahi Kasei has been invited to showcase at Filo fair, the international exhibition of orthogonal weaving yarns for clothing and furnishings, circular knitwear and technical textiles, in a new special area, a dedicated open space reserved to sustainable fibers that will allow visitors to discover all their production cycle and performances, in full relax and transparency.

Bemberg™, an exceptional fiber made from the smart-tech transformation of cotton linters pre-consumer materials and converted through a traceable and transparent closed loop process, will brings to Filo its history, experience, know-how and market partnerships to prove its versatility and design-driven look and touch Last but not least we are talking about a true circular economy-oriented ingredient, with certified sustainable performance: Bemberg™ is biodegradable and compostable material as verified by the INNOVHUB 3rd party test and it has GRS (Global Reycled Standard) certification from Textile Exchange proving recycling authenticity.

Bemberg™ application history starts with high-quality suit lining, but today we can find it in many other applications such as fashion couture, outerwear, innerwear, bedding, and sportswear where its amazing unique touch and quality is offering a distinctive performance.

And to prove all of this, Bemberg™ will be at Filo showing some selected fabric innovation, and three responsible-driven designers representing different and complementary part of contemporary consumer wardrobe: ZEROBARRACENTO, Maurizio Miri and WAXEWUL - who have all chosen Bemberg™ fiber to create special collections. Three different ways to see and represent how sustainability and style – even if completely different ones – together can be highly successful, performing and interesting to the new consumer.

ZEROBARRACENTO, a gender-neutral emerging outerwear brand focusing on zero-waste product development, selects Bemberg™ for two fundamental reasons: firstly, from a stylistic point of view for its extreme versatility: in the various collections we have adopted it to create Kimonos, padded jackets, wrap dresses as well as for the interiors of our garments, which are intended to be soft embraces for total physical and mental comfort. The second but no less important reason is that this fibre has circular values in line with their zero-waste commitment.

The concept of the brand "Maurizio Miri" has a strong personality and a clear intent: to create a product that stimulates the wearer towards beauty. A garment should not simply be worn, but it has also to create a perfect symbiosis with the person wearing it and generate an exchange of positive energies. The purpose is to make the individual feel in perfect harmony with their own image. With this aim in mind, the designer selects extremely precious Bemberg™ linings for their sophisticated tailor jackets. 

Finally, WAXEWUL, a brand of sartorial clothing and artisan accessories with an urban-afro soul that has environmental and social sustainability as its basic ethics. WAXEWUL will bring to Filo its brand-new product, the J_Hood Bag: a doubleface jacket with a comfortably removable hood that can be transformed into a finely hidden doubleface bag. An exclusive, innovative and sustainable garment with minimal impact on the environment made of BemBAZIN™ - a new generation of bazin created, patented and produced by Brunello which is composed by the high-tech and responsible fibers of Bemberg™ - on one side and of wax on the other, traceable and certified, guaranteeing a reduction in waste (two jackets in one) and a long-life cycle.

14.09.2021

Kornit Digital: 2020 Impact and Environmental, Social, and Governance Report released

Kornit Digital Ltd., a worldwide market leader in digital textile production technologies, released its 2020 Impact and Environmental, Social, and Governance (“ESG”) Report. This inaugural report affirms Kornit’s commitment to achieving specific ESG goals. This includes the way Kornit conducts business, creates meaningful impact in local communities, and achieves environmental sustainability, in addition to how Kornit will continue to build a diverse and inclusive company culture, foster employee growth and development, and empower fair and safe labor practices globally.
 

Kornit Digital Ltd., a worldwide market leader in digital textile production technologies, released its 2020 Impact and Environmental, Social, and Governance (“ESG”) Report. This inaugural report affirms Kornit’s commitment to achieving specific ESG goals. This includes the way Kornit conducts business, creates meaningful impact in local communities, and achieves environmental sustainability, in addition to how Kornit will continue to build a diverse and inclusive company culture, foster employee growth and development, and empower fair and safe labor practices globally.
 
In addition to enabling eco-friendly production processes with technology and consumables that use less water, reduce waste, and minimize the carbon footprint, Kornit technology solutions enable sustainable production on demand, which eliminates overproduction of apparel and other textile goods. A 2021 Life Cycle Assessment conducted on two flagship products, the Kornit Atlas MAX and Kornit Presto S, demonstrated that relative to traditional analog processes, Kornit’s digital production systems used up to 95% less water and 94% less energy, and produced up to 83% less greenhouse gas (GHG) emissions for the Presto S system and up to 93% less water and 66% less energy, and produced up to 82% less greenhouse gas (GHG) emissions for the Atlas MAX system.


Based on this study, in addition to past sustainability performance results and strategic projections for business growth and market expansion, by 2026 Kornit Digital’s sustainable on-demand solutions are expected to enable the production of approximately 2.5 billion apparel items in a responsible manner to deliver:

  • Zero overproduction: By moving the industry to on-demand manufacturing, Kornit will help eliminate the estimated 1.1 billion apparel items overproduced using traditional production methods, based on an industry average of 30% overproduction. This is about 1 apparel item for each and every person living in Europe and North America – saved.
  • Zero water waste: In addition to eliminating overstocks, Kornit-enabled production on demand will support saving an estimated 4.3 trillion liters (1.1 trillion gallons) of water. This is the estimated amount of drinking water needed for the entire U.S. population for 11 years.
  • Reduced CO2 emissions: By enabling sustainable on-demand production, consuming less energy, and generating less waste, Kornit will prevent an estimated 17.2 billion kilograms (37.9 billion pounds) of greenhouse gas emissions, compared to traditional manufacturing methods. This is equivalent to the estimated amount of carbon dioxide emitted from circumnavigating the entire planet with a car nearly 2,400 times.

Furthermore, the report outlines Kornit’s commitment to achieving KPIs that address waste, chemicals, GHG emissions, energy, product development, employee training, diversity and inclusion, and the company’s supply chain.

Source:

pr4u

Rieter CAMPUS – Foundation Stone Laid (c) Rieter
Rieter Campus Winterthur
09.09.2021

Rieter CAMPUS – Foundation Stone Laid

  • Rieter CAMPUS strengthens innovation strategy and technology leadership position
  • Customer and technology center and administration building ready for occupancy in 2024
  • Commitment to the Winterthur site and to Switzerland as a business location

On September 8, 2021, the foundation stone was laid for the Rieter CAMPUS on the western part of the Rieter site at the Winterthur location, which includes a customer and technology center as well as an administration building. The Rieter CAMPUS will make an important contribution to the implementation of the innovation strategy and to the enhancement of the company’s technology leadership position. At the same time, the investment of around CHF 80 million is a commitment to the Winterthur site and to Switzerland as a business location. 

  • Rieter CAMPUS strengthens innovation strategy and technology leadership position
  • Customer and technology center and administration building ready for occupancy in 2024
  • Commitment to the Winterthur site and to Switzerland as a business location

On September 8, 2021, the foundation stone was laid for the Rieter CAMPUS on the western part of the Rieter site at the Winterthur location, which includes a customer and technology center as well as an administration building. The Rieter CAMPUS will make an important contribution to the implementation of the innovation strategy and to the enhancement of the company’s technology leadership position. At the same time, the investment of around CHF 80 million is a commitment to the Winterthur site and to Switzerland as a business location. 

With a floor area of over 30 000 m2, the Rieter CAMPUS offers space for around   700 ultra-modern workplaces. For this purpose, Rieter and a specialist in office architecture have developed a contemporary space concept for the “Open Space Office” that is tailored to the needs of the company, divided into meeting rooms, focus rooms and some individual offices. The underground car park provides   88 parking spaces, and a further 12 outdoor parking spaces are being created   in front of the technology center.  “In the course of its 225-year company history, Rieter has helped shape the city of Winterthur. The foundation for the future as a leading technology company is now being created with the new CAMPUS. In this way, Rieter is giving a clear indication   of its commitment to the Winterthur site and to Switzerland as a business location”, commented Bernhard Jucker, Chairman of the Board of Directors of Rieter Holding AG.

Innovation is an important part of Rieter’s strategy and crucial for the company’s success. For this reason, Rieter invests more than CHF 50 million annually in research and development. Thanks to this commitment, Rieter is making a   decisive contribution to the further development of systems for sustainable yarn production and their digitization. The Rieter CAMPUS will provide an attractive working environment that promotes creativity and innovation.  The new CAMPUS is a showcase project in terms of economic feasibility, energy efficiency and sustainability. Rieter relies on renewable energy for construction. This includes heat generation via geothermal probes and a photovoltaic system on around 1 300 m2 of roof area. “In this way, the entrepreneurial focus on sustainable and energy-efficient solutions for yarn production is reflected in the overall concept of the CAMPUS,” emphasized Rieter CEO Norbert Klapper.  The move into the new building is planned for 2024.

Source:

Rieter Management AG

07.09.2021

Lenzing AG: Early termination of contract with Stefan Doboczky

  • CEO Stefan Doboczky will not extend contract and will step down at end of third quarter 2021

The Supervisory Board of Lenzing AG, a world’s leading producer of wood-based cellulosic fibers, has come to a mutual agreement with its longstanding Chief Executive Officer Stefan Doboczky to end his contract. Doboczky has informed the Supervisory Board that he will not be available for another extension of his contract. With great regret the Supervisory Board of Lenzing AG accepts his resignation and the parties mutually agreed to end the contract effective September 30, 2021.

  • CEO Stefan Doboczky will not extend contract and will step down at end of third quarter 2021

The Supervisory Board of Lenzing AG, a world’s leading producer of wood-based cellulosic fibers, has come to a mutual agreement with its longstanding Chief Executive Officer Stefan Doboczky to end his contract. Doboczky has informed the Supervisory Board that he will not be available for another extension of his contract. With great regret the Supervisory Board of Lenzing AG accepts his resignation and the parties mutually agreed to end the contract effective September 30, 2021.

“My sincere thanks go to Stefan Doboczky for his exceptional achievements at Lenzing. The design and implementation of the transformation of Lenzing AG into a global specialty fiber leader and the positioning of the company as a recognized sustainability champion have been major accomplishments of Stefan Doboczky over the last years”, said Chairman of the Supervisory Board, Peter Edelmann. “Thanks to his leadership, Lenzing AG finds itself today on a stable and profitable growth track with a clear commitment to become climate-neutral by 2050. And all of that in spite of the challenging environment of the COVID-19 pandemic”, said Edelmann.

Stefan Doboczky: “Developing and consistently implementing the Lenzing strategy has been the cornerstone of my work in recent years. After extensive consideration, I have decided that this is the right time for a personal change. The strategy is in place, the company is well on track – now is the ideal moment to pass on the baton. And one thing is certain: Lenzing will always have a very special place in my heart.”

Lenzing AG remains on track with its guidance for the full year 2021 as announced with the half-year results. Cord Prinzhorn has been appointed interim CEO. Prinzhorn is Member of the Supervisory Board of Lenzing AG and will be available until a successor is found. The Supervisory Board will immediately start the search process.

More information:
Lenzing AG Stefan Doboczky
Source:

Lenzing AG

B.I.G. YARNS awarded HPR status for second European plant © Beaulieu International Group
B.I.G. YARNS awarded HPR status for second European plant.
07.09.2021

B.I.G. YARNS awarded HPR status for second European plant

  • FM Global ‘Highly Protected Risk’ Achievement Award for Komen site, Belgium
  • Completes HPR Award status for B.I.G. YARNS’ European production facilities
  • Fifth plant in Beaulieu International Group to attain HPR Award

B.I.G. YARNS is proud to announce the attainment of a FM Global ‘Highly Protected Risk’ Achievement Award (HPR Award) for its yarn production facility in Komen, Belgium.

The HPR Award is assigned by insurer FM Global, Beaulieu International Group’s insurance partner of the past five years in its on-going dedication to property loss prevention. A worldwide team of engineers focuses on providing assistance and protection of B.I.G.’s assets, helping the Group to achieve a higher level of risk protection. The FM Global assessment considers implementation of measures to protect against fire, natural hazard, mechanical breakdown of machinery and also cyber risks. The local team worked diligently over the last five years to implement all the FM Global recommendations.

  • FM Global ‘Highly Protected Risk’ Achievement Award for Komen site, Belgium
  • Completes HPR Award status for B.I.G. YARNS’ European production facilities
  • Fifth plant in Beaulieu International Group to attain HPR Award

B.I.G. YARNS is proud to announce the attainment of a FM Global ‘Highly Protected Risk’ Achievement Award (HPR Award) for its yarn production facility in Komen, Belgium.

The HPR Award is assigned by insurer FM Global, Beaulieu International Group’s insurance partner of the past five years in its on-going dedication to property loss prevention. A worldwide team of engineers focuses on providing assistance and protection of B.I.G.’s assets, helping the Group to achieve a higher level of risk protection. The FM Global assessment considers implementation of measures to protect against fire, natural hazard, mechanical breakdown of machinery and also cyber risks. The local team worked diligently over the last five years to implement all the FM Global recommendations.

Emmanuel Colchen, General Manager B.I.G. YARNS, comments: “Achieving the prestigious HPR Award recognizes the commitment of the teams at B.I.G. YARNS and the wider Beaulieu International Group to proactive risk management and contingency planning to ensure the safety and protection of our workplaces. Safeguarding property is a key element in enabling us to provide business continuity for our customers in demanding sectors like automotive, commercial contract and residential flooring.”

B.I.G. YARNS’ Komen production facility is the fifth plant at B.I.G. to receive HPR status - the highest level a plant can achieve for fire risk prevention and protection.

The Yarns division of Beaulieu International Group achieved HPR status for its other European site in Comines, France, in 2017.

01.09.2021

CHT Group generates 62% of 2020 sales with sustainable products

  • Sustainability Report 2020 published

As an internationally positioned company, the CHT Group is one of the leading suppliers of speciality chemicals. The company supplying chemical products for the most diverse applications and industries, presented their annual edition of the Sustainability Report, for the period January to December 2020,

The report has been prepared in accordance with the standards of the Global Reporting Initiative (GRI) and is based on the Core option. The focus is on human resources development, energy and water consumption as well as company-wide emissions and waste management.

Particularly noteworthy here is the group-wide reduction in specific resource consumption in the areas under review. In relation to the volume produced, for example, the following key figures show the reduction of environmental impacts:

  • Sustainability Report 2020 published

As an internationally positioned company, the CHT Group is one of the leading suppliers of speciality chemicals. The company supplying chemical products for the most diverse applications and industries, presented their annual edition of the Sustainability Report, for the period January to December 2020,

The report has been prepared in accordance with the standards of the Global Reporting Initiative (GRI) and is based on the Core option. The focus is on human resources development, energy and water consumption as well as company-wide emissions and waste management.

Particularly noteworthy here is the group-wide reduction in specific resource consumption in the areas under review. In relation to the volume produced, for example, the following key figures show the reduction of environmental impacts:

  • 21% share of renewable energies in total consumption
  • 440,000 EUR investment in environmental protection and nature conservation
  • 5.8% less energy consumption and less CO2 emission

62% of CHT Group's 2020 sales were generated with sustainable products. For this, 91% of the strategic raw material volume was sourced from suppliers classified as sustainable.

At the center of the report are the current working topics and outlooks that showcase CHT's commitment to sustainability and its innovative strength to achieve the United Nations Sustainable Development Goals (SDGs).

CHT considers 11 of the SDGs to be particularly relevant for the future of the Group of companies. For this reason, the recently revised global corporate strategy is directly geared to the Sustainable Development Goals of the United Nations.

The current edition of the report, which is published for the first time exclusively online in a resource-saving manner, is available here: https://sustainability-report.cht.com

More information:
CHT Group Sustainability Report
Source:

CHT Gruppe

31.08.2021

DSM and SABIC: Creating recycled-based Dyneema®

Royal DSM, a global science-based company in Nutrition, Health and Sustainable Living, and SABIC, a global leader in the chemical industry, announced a collaboration to create recycled-based Dyneema®. Through a joint pilot with multiple CirculariTeam® members, the manufacturing and usage of Dyneema® using mixed plastic waste as feedstock (via mass balance approach) will be successfully demonstrated. It is an important step toward the future goal of fully closing the loop by delivering Dyneema® made from ultra-high molecular weight polyethylene (UHMwPE) waste. This collaboration underlines DSM’s and SABIC’s efforts to accelerate a circular economy for materials.

Royal DSM, a global science-based company in Nutrition, Health and Sustainable Living, and SABIC, a global leader in the chemical industry, announced a collaboration to create recycled-based Dyneema®. Through a joint pilot with multiple CirculariTeam® members, the manufacturing and usage of Dyneema® using mixed plastic waste as feedstock (via mass balance approach) will be successfully demonstrated. It is an important step toward the future goal of fully closing the loop by delivering Dyneema® made from ultra-high molecular weight polyethylene (UHMwPE) waste. This collaboration underlines DSM’s and SABIC’s efforts to accelerate a circular economy for materials.

By working together with members of CirculariTeam®, DSM will produce recycled-based Dyneema® made using SABIC’s certified circular ethylene as a pilot project in both a sailing rope and a pelagic trawl net application. The circular ethylene, from SABIC’s TRUCIRCLE™ portfolio, uses mixed plastic waste as feedstock (mass balance approach), which not only contributes to preventing valuable plastic from becoming waste and the avoidance of carbon emissions compared to incineration, but it will also help preserve fossil resources. These pilots are an important early-stage milestone in the journey toward making fully circular Dyneema® from HMPE post-production and post-consumer waste.

Jon Mitchell, Managing Director at Marlow Ropes: “We’re proud to be one of the first manufacturers to integrate recycled-based Dyneema® within our products and demonstrate the material’s feasibility. By collaborating with materials science pioneers such as DSM and SABIC, we are able to create products that not only deliver superlative functional performance but also have a lower environmental impact. Our products are trialed and tested by professional offshore sailing teams including 11th Hour Racing Team, a proud partner of ours at Marlow, with whom we share a progressive approach to seeking sustainable solutions: no more business as usual."

Klaus Walther, Managing Director at Gleistein: “Warm congratulations to DSM and SABIC for pushing the boundaries of science to deliver a truly unique product. We’re proud that our ropes can be produced from what once was typical household plastic waste. This is an important stepping stone towards becoming circular. It will enable our customer Maritiem BV to further develop high-tech fishing gear whilst contributing to the circular economy. Not to forget Cornelis Vrolijk Fishing Company, who again illustrate their commitment to Corporate Social Responsibility by introducing this concept in fishery.”

More information:
DSM Dyneema SABIC plastic waste
Source:

EMG for DSM

30.08.2021

Biden Administration Awards $6.5M Contract to US Cotton LLC

  • Ramping Up Production of American-Made Polyester Tipped Swabs

The Biden Administration has awarded a contract for $6.5 million to U.S. Cotton LLC, the largest manufacturer of cotton swabs in the United States, to increase domestic production capability for polyester tipped swabs for home testing kits and mass testing applications to fight the COVID-19 pandemic.  Since the beginning of the pandemic, U.S. Cotton has retooled operations to produce over 400 million COVID testing kit swabs.

The Department of Defense (DOD), in coordination with the Department of Health and Human Services (HHS), announced the award today as part of the administration’s broader effort to increase domestic production capability for essential medical supplies.

U.S. Cotton, based in Cleveland, Ohio, said the company will increase its production capacity from 92 million polyester swab tips per month to approximately 371 million polyester swab tips per month by May 2022 to support domestic COVID-19 testing. The DOD contract award was funded through the American Rescue Plan Act (ARPA) to support the domestic industry base expansion for critical medical resources.

  • Ramping Up Production of American-Made Polyester Tipped Swabs

The Biden Administration has awarded a contract for $6.5 million to U.S. Cotton LLC, the largest manufacturer of cotton swabs in the United States, to increase domestic production capability for polyester tipped swabs for home testing kits and mass testing applications to fight the COVID-19 pandemic.  Since the beginning of the pandemic, U.S. Cotton has retooled operations to produce over 400 million COVID testing kit swabs.

The Department of Defense (DOD), in coordination with the Department of Health and Human Services (HHS), announced the award today as part of the administration’s broader effort to increase domestic production capability for essential medical supplies.

U.S. Cotton, based in Cleveland, Ohio, said the company will increase its production capacity from 92 million polyester swab tips per month to approximately 371 million polyester swab tips per month by May 2022 to support domestic COVID-19 testing. The DOD contract award was funded through the American Rescue Plan Act (ARPA) to support the domestic industry base expansion for critical medical resources.

John Nims, President of U.S. Cotton said, “We are proud to be involved in a national effort to help deploy these testing kit swabs for the American people. These swabs are designed to make it easier for people at home to self-administer coronavirus tests and will also be used for mass testing applications, which is critically important. We greatly appreciate the collaboration with DOD and HHS to ramp up essential capacity of polyester-based synthetic swabs that will help in the fight against the pandemic.

“We continue to step up to meet our nation’s critical need for American-made coronavirus testing kit swabs on a massive scale. It is an honor to work with our government to help fight this pandemic and use our innovative technologies based here in the United States to fill a national and global demand for testing kits. I especially want to thank Senator Brown and Senator Portman for all their incredible support to help us retool and expand our operations in Cleveland. We can’t thank them enough for their tireless work and also want to recognize their hard working staff. As the Delta variant surges across the country, this timely investment will help in the fight against COVID by adding this much-needed, long-term surge capacity.”

Kim Glas, President and CEO of NCTO, said, “We want to sincerely thank President Biden, the Department of Defense, and the Department of Health and Human Services for leading this critical industrial expansion effort. We appreciate the administration’s commitment to expand the U.S. industrial base for these essential products.  We have a once-in-a-generation opportunity to onshore these critical supply chains long-term and we look forward to working with the administration and Congress to advance long-term solutions.”

More information:
corona virus NCTO
Source:

NCTO

Graphical material: Borealis
26.08.2021

Drinking cups using chemically recycled polypropylene

Swiss dairy company Emmi is partnering with Borealis and Greiner Packaging to produce iced coffed drinking cups using chemically recycled polypropylene.

The cups are produced by Greiner Packaging and the chemically recycled material comes from Borealis, one of the world’s leading providers of advanced and circular polyolefin solutions based in Vienna, Austria.

Emmi, Switzerland’s largest milk processor is committed to climate protection and the circular economy. The dairy company has the stated goal to make all of its packaging 100% recyclable and is committed to various measures to promote circularity such as packaging that contains at least 30% recyclate by 2027.

Swiss dairy company Emmi is partnering with Borealis and Greiner Packaging to produce iced coffed drinking cups using chemically recycled polypropylene.

The cups are produced by Greiner Packaging and the chemically recycled material comes from Borealis, one of the world’s leading providers of advanced and circular polyolefin solutions based in Vienna, Austria.

Emmi, Switzerland’s largest milk processor is committed to climate protection and the circular economy. The dairy company has the stated goal to make all of its packaging 100% recyclable and is committed to various measures to promote circularity such as packaging that contains at least 30% recyclate by 2027.

From September 2021 Emmi will use at least 100 tonnes of plastic based on the recycled material each year. Chemical recycling renews plastic back to plastic creating recycled materials with a level of purity equivalent to fossil-fuel based PP and hence, fit for protective, food-safe and other demanding applications. In this way, Emmi is utilizing difficult to recycle feedstock preventing plastic waste that would be likely landfilled or incinerated. In the future, depending on the availability of suitable material, the amount of recycled plastic in packaging is to be further increased.

The new technology to recover the polypropylene is currently still in its infancy, where Greiner Packaging and Borealis are leading the way. Only limited quantities of chemically recycled polypropylene are currently available, and Emmi is one of only a few food manufacturers to have secured a share of the chemically recycled polypropylene plastic through its early commitment and long-standing collaboration with the development companies.

The chemically recycled material used for the cups consists entirely and solely of ISCC (International Sustainability & Carbon Certification) material, on a mass balance basis. Mass balance is a methodology that makes it possible to track the amount and sustainability characteristics of circular and/or bio-based content in the value chain and through each step of the process. This provides transparency ultimately also to the consumers, enabling them to know that the product they are buying is based on this renewable material.

More information:
Polypropylen Borealis
Source:

Borealis

Photo: Sateri
26.08.2021

EU-BAT Compliance Confirmed for all Sateri Viscose Fibre Mills

  • Achievement Ahead of Schedule

All of Sateri’s five viscose mills in China are now fully compliant with the emission limits set out in the European Union Best Available Techniques Reference Document (EU-BAT BREF) on Polymers, following recent verification of Sateri Jiangsu and Sateri China mills.

Verified by independent consultant Sustainable Textile Solutions (STS), a division of BluWin Limited (UK), the parameters assessed included resource utility efficiency, wastewater discharge and air emission.

Allen Zhang, President of Sateri said, “Sateri Jiangsu was established in 2019 following an acquisition while Sateri China was built in the same year. We had aimed to have both mills meet EU-BAT’s recommended emission levels by 2023. To achieve this two years ahead of schedule underscores our continuous efforts in process improvement and control of pollutant emissions, and resource utilization efficiency. We will continue to pursue manufacturing excellence and invest in best-in-class technologies for all our mills – existing, acquired, and newly constructed ones – as part of our Vision 2030 commitment towards closed-loop and cleaner production.”

  • Achievement Ahead of Schedule

All of Sateri’s five viscose mills in China are now fully compliant with the emission limits set out in the European Union Best Available Techniques Reference Document (EU-BAT BREF) on Polymers, following recent verification of Sateri Jiangsu and Sateri China mills.

Verified by independent consultant Sustainable Textile Solutions (STS), a division of BluWin Limited (UK), the parameters assessed included resource utility efficiency, wastewater discharge and air emission.

Allen Zhang, President of Sateri said, “Sateri Jiangsu was established in 2019 following an acquisition while Sateri China was built in the same year. We had aimed to have both mills meet EU-BAT’s recommended emission levels by 2023. To achieve this two years ahead of schedule underscores our continuous efforts in process improvement and control of pollutant emissions, and resource utilization efficiency. We will continue to pursue manufacturing excellence and invest in best-in-class technologies for all our mills – existing, acquired, and newly constructed ones – as part of our Vision 2030 commitment towards closed-loop and cleaner production.”

Chen Xinwei, Chairman of China Chemical Fiber Industry Association, said, "China's regenerated cellulose fibre industry has been progressing steadily in recent years. As a major viscose manufacturer, Sateri has demonstrated leadership in benchmarking itself against advanced domestic and international standards, focusing on low-carbon development, energy-saving and emission-reduction technology, and cleaner production to advance sustainable development, as well as enhance the company’s competitiveness. All other players in the industry should be encouraged to follow suit."

Sateri is a member of the RGE group of companies; Sateri’s other three mills - Sateri Fujian, Sateri Jiujiang and Sateri China (Jiangxi) - had attained EU-BAT compliance in 2020.

Source:

Omnicom Public Relations Group

3D-Lofter. Photo: (c) DiloGroup
26.08.2021

DiloGroup at INDEX

After a long break, the international nonwovens industry will meet again in Geneva, Switzerland, from October 19 to 22, 2021 on the occasion of INDEX. DiloGroup offers tailormade production systems from one supplier and will inform about its portfolio and the latest equipment developments from fibre opening to the finished felt.

A new, simplified elliptical needle beam drive makes Hyperpunch technology also attractive for standard application. Hyperpunch HαV allows a more uniform stitch distribution in the preneedling process especially in combination with the new needle pattern 6000X. In a complete needling line this felt homogenization process can be improved further by using the new needle pattern 8000X which is a milestone in the needle pattern development process and results in endproduct surfaces with low markings over a wide range of advances/stroke.

After a long break, the international nonwovens industry will meet again in Geneva, Switzerland, from October 19 to 22, 2021 on the occasion of INDEX. DiloGroup offers tailormade production systems from one supplier and will inform about its portfolio and the latest equipment developments from fibre opening to the finished felt.

A new, simplified elliptical needle beam drive makes Hyperpunch technology also attractive for standard application. Hyperpunch HαV allows a more uniform stitch distribution in the preneedling process especially in combination with the new needle pattern 6000X. In a complete needling line this felt homogenization process can be improved further by using the new needle pattern 8000X which is a milestone in the needle pattern development process and results in endproduct surfaces with low markings over a wide range of advances/stroke.

The “3D-Lofter” which was first presented during ITMA 2019 in Barcelona offers a wider range of nonwovens applications by exploring the third dimension. A series of single web forming units which work according to the aerodynamic web forming principle deliver defined fibre masses in varied patterns on a base needlefelt. A stress oriented production of technical formed parts resulting in fibre savings or patterned DI-LOUR or DI-LOOP felts are two examples for this technology which explores new application areas for needlefelts The 3D-Lofter technology may also be used “inverted” for filling up bad spots in web mats and thus achieves a better homogeneity of e. g. spunlace, thermobond or airlay products.

The DiloLine 4.0 concept offer I4.0 modules which not only support the user but also facilitate quality control and maintenance by a maximum data transparency in production and control of operation. The Dilo solutions “Smart Start” for a fully automatic start of the production line or “DI-LOWATT” for energy savings are accompanied by Siemens solutions which can be selected via App or Data Cloud “MindSphere”.

Apart from machines for needling technology we offer in cooperation with partner companies also production lines including thermobonding and hydroentangling components.

More information:
DiloGroup Dilo INDEX
Source:

DiloGroup

(c) Suominen Corporation
24.08.2021

Suominen: Progress in Sustainability, decreasing EBITDA expected

As part of Suominen Corporation’s Half-Year Financial Report for January 1 – June 30, 2021 the company shared their insights and actions defined in their sustainability agenda.
A new Code of Conduct was launched in the beginning of 2021 and a mandatory training program about the Code will be start in the third quarter of this year.

Suominen is committed to continuously improving their production efficiency and the efficient utilization of natural resources. What active measures towards reducing energy consumption, greenhouse gas emissions, water consumption and waste to landfill are concerned, the commitment is to diminish them by 20% per ton of product by 2025 compared to the base year of 2019.
Offering a comprehensive portfolio of sustainable nonwovens and continuously developing new and innovative solutions with a reduced environmental impact, the target is a 50% increase in sales of sustainable nonwovens by 2025 compared to 2019, and to have at least 10 sustainable product launches per year. During the first half of the year, nine sustainable product launches were made.

As part of Suominen Corporation’s Half-Year Financial Report for January 1 – June 30, 2021 the company shared their insights and actions defined in their sustainability agenda.
A new Code of Conduct was launched in the beginning of 2021 and a mandatory training program about the Code will be start in the third quarter of this year.

Suominen is committed to continuously improving their production efficiency and the efficient utilization of natural resources. What active measures towards reducing energy consumption, greenhouse gas emissions, water consumption and waste to landfill are concerned, the commitment is to diminish them by 20% per ton of product by 2025 compared to the base year of 2019.
Offering a comprehensive portfolio of sustainable nonwovens and continuously developing new and innovative solutions with a reduced environmental impact, the target is a 50% increase in sales of sustainable nonwovens by 2025 compared to 2019, and to have at least 10 sustainable product launches per year. During the first half of the year, nine sustainable product launches were made.

OUTLOOK FOR 2021
As announced on August 12, 2021 Suominen expects that its comparable EBITDA (earnings before interest, taxes, depreciation and amortization) in 2021 will decrease from 2020 due to the slowdown in the demand for nonwovens in the second half of 2021 as well as some continuing volatility in the raw material and transportation markets. In 2020, Suominen’s comparable EBITDA was EUR 60.9 million.

More information:
Suominen nonwovens
Source:

Suominen Corporation