From the Sector

The DITF is leading the joint project "DACCUS-Pre*". The basic idea of the project is to develop a new building material that stores carbon in the long term and removes more CO₂ from the atmosphere than is emitted during its production.       

In collaboration with the company TechnoCarbon Technologies, the project is now well advanced - a first demonstrator in the form of a house wall element has been realized. It consists of three materials: Natural stone, carbon fibers and biochar. Each component contributes in a different way to the negative CO₂ balance of the material:

Two slabs of natural stone form the exposed walls of the wall element. The mechanical processing of the material, i.e. sawing in stone cutting machines, produces significant quantities of stone dust. This is very reactive due to its large specific surface area. Silicate weathering of the rock dust permanently binds a large amount of CO₂ from the atmosphere.

Carbon fibers in the form of technical fabrics reinforce the side walls of the wall elements. They absorb tensile forces and are intended to stabilize the building material in the same way as reinforcing steel in concrete. The carbon fibers used are bio-based, produced from biomass. Lignin-based carbon fibers, which have long been technically optimized at DITF Denkendorf, are particularly suitable for this application: They are inexpensive due to low raw material costs and have a high carbon yield. In addition, unlike reinforcing steel, they are not susceptible to oxidation and therefore last much longer. Although carbon fibers are more energy-intensive to produce than steel, as used in reinforced concrete, only a small amount is needed for use in building materials. As a result, the energy and CO₂ balance is much better than for reinforced concrete. By using solar heat and biomass to produce the carbon fibers and the weathering of the stone dust, the CO₂ balance of the new building material is actually negative, making it possible to construct CO₂-negative buildings.

The third component of the new building material is biochar. This is used as a filler between the two rock slabs. The char acts as an effective insulating material. It is also a permanent source of CO₂ storage, which plays a significant role in the CO₂ balance of the entire wall element.

From a technical point of view, the already realized demonstrator, a wall element for structural engineering, is well developed. The natural stone used is a gabbro from India, which has a high-quality appearance and is suitable for high loads. This has been proven in load tests.  Bio-based carbon fibers serve as the top layer of the stone slabs. The biochar from Convoris GmbH is characterized by particularly good thermal insulation values.

The CO₂ balance of a house wall made of the new material has been calculated and compared with that of conventional reinforced concrete. This results in a difference in the CO₂ balance of 157 CO₂ equivalents per square meter of house wall. A significant saving!

* (Methods for removing atmospheric carbon dioxide (Carbon Dioxide Removal) by Direct Air Carbon Capture, Utilization and Sustainable Storage after Use (DACCUS).

INDA, the Association of the Nonwoven Fabrics Industry, announced a call for abstracts for IDEA®, April 29-May 1, 2025, Miami Beach Convention Center, Miami Beach, Florida. IDEA attracts thousands of nonwoven professionals from all functional areas spanning the entire supply chain.

The theme for IDEA25 is “Nonwovens for a Healthier Planet” highlighting nonwoven advancements in sustainability.

Product developers, designers, engineers, technical scouts, and marketing professionals accountable for their product’s environmental impact will attend IDEA. Presentations will focus on responsible sourcing, innovations in sustainability, and end-of-life solutions for nonwovens and its related industries.

A few examples of topics for consideration are:

RESPONSIBLE SOURCING

• Natural Fibers (Cotton, Hemp, Bamboo, Banana, Wood Pulp, Regenerated Cellulose, Wool, Fur, Chitin, Feathers)
• Polymers (Biopolymers, Regenerated and Recycled polymers, Unconventional and Alternatives to Traditional Polymers)
• Sustainable Chemistries (finishes, lubricants, adhesives, and additives)

INNOVATIONS IN SUSTAINABILITY

• Process Improvements with Sustainability Impact (reduced waste, reduced energy, reduced water consumption)
• Product Design Improvements with Sustainability Impact (lightweighting, designs for end-of-life, “good enough” design)

END-OF-LIFE SOLUTIONS

• End-of-Life or Next-Life Considerations (compostability, biodegradability, recycling, advanced recycling and circularity)
• Presenting is an opportunity for technical professionals to showcase pioneering research, innovative solutions, and expert insights with technology scouts.

Abstracts must be submitted via the INDA website by June 7, 2024.

Since inventing the first fleece crafted from recycled plastic water bottles more than three decades ago, Polartec®, a Milliken & Company brand, and the creator of innovative and more sustainable textile solutions, has upheld its pledge to protect the environment.

With its new Beyond Begins Today initiative, Polartec aims to raise awareness around the important global themes of sustainability, diversity and positive change.

Polartec is engaged to make the goal of zero waste a reality – from using 100% recycled and plant-based materials, to delivering certified waste reductions and innovative technologies that reduce the impact of its activities.

Beyond Begins Today is a multifaceted campaign featuring static and multimedia content, including short films released throughout the year via multiple touchpoints and channels – the first of which will be released on Earth Day 2024 to underscore the underlying premise that the future is what we make it. Polartec’s commitment to sustainable solutions go beyond the integration of increasingly advanced manufacturing methods or the ongoing exploration of novel fibers, and continued investments in sustainable materials development.

Polartec’s promises that every product launches in 2024 will either reduce the impact on the planet, endure the test of time, or contribute to circularity processes. Beyond Begins Today looks at how Polartec fabrics are made to last, and made to be used and enjoyed from one generation to the next and beyond. It explores the innovative monomaterials, repurposed plastic and plant-based nylon membranes and fabrics that Polartec uses to set new standards for high performance materials and the ambitious climate-related objectives across the entire value chain that exceed existing mandates. This holistic strategy shall allow Polartec to stay at the forefront of its industry by producing top-notch textiles that champion environmental stewardship and pave the way for a more sustainable tomorrow.

The 17th World-Pultrusion-Conference (WPC) took place in Hamburg from 29 February to 1 March. Pultrusion, also known as the extrusion process, is a highly efficient method for producing fibre-reinforced plastic profiles for various applications in the construction/infrastructure and transport sectors.

A record number of almost 150 participants from all over the world attended the event. An international audience of experts from Europe and the USA, as well as China, India and Japan was represented.

The lecture programme with a total of 25 specialist lectures was strongly characterised by the topic of sustainability. The process development of thermoplastic pultrusion and applications in wind energy, solar panels, bridge construction and the automotive industry were also discussed at length. Despite the difficult market environment, many opportunities and possibilities for the pultrusion industry were presented.

The conference takes place every two years in a European country of importance to the pultrusion industry and is organised by AVK for the European Pultrusion Technology Association (EPTA), in cooperation with the American Composites Manufacturers Association (ACMA).

The German Institutes of Textile and Fiber Research Denkendorf (DITF) have modernized and expanded their melt spinning pilot plant with support from the State of Baden-Württemberg. The new facility enables research into new spinning processes, fiber functionalization and sustainable fibers made from biodegradable and bio-based polymers.

In the field of melt spinning, the DITF are working on several pioneering research areas, for example the development of various fibers for medical implants or fibers made from polylactide, a sustainable bio-based polyester. Other focal points include the development of flame-retardant polyamides and their processing into fibers for carpet and automotive applications as well as the development of carbon fibers from melt-spun precursors. The development of a bio-based alternative to petroleum-based polyethylene terephthalate (PET) fibers into polyethylene furanoate (PEF) fibers is also new. Bicomponent spinning technology, in which the fibers can be produced from two different components, plays a particularly important role, too.

Since polyamide (PA) and many other polymers were developed more than 85 years ago, various melt-spun fibers have revolutionized the textile world. In the field of technical textiles, they can have on a variety of functions: depending on their exact composition, they can for example be electrically conductive or luminescent. They can also show antimicrobial properties and be flame-retardant. They are suitable for lightweight construction, for medical applications or for insulating buildings.

In order to protect the environment and resources, the use of bio-based fibers will be increased in the future with a special focus on easy-to-recycle fibers. To this end, the DITF are conducting research into sustainable polyamides, polyesters and polyolefins as well as many other polymers. Many 'classic', that is, petroleum-based polymers cannot or only insufficiently be broken down into their components or recycled directly after use. An important goal of new research work is therefore to further establish systematic recycling methods to produce fibers of the highest possible quality.

For these forward-looking tasks, a bicomponent spinning plant from Oerlikon Neumag was set up and commissioned on an industrial scale at the DITF in January. The BCF process (bulk continuous filaments) allows special bundling, bulking and processing of the (multifilament) fibers. This process enables the large-scale synthesis of carpet yarns as well as staple fiber production, a unique feature in a public research institute. The system is supplemented by a so-called spinline rheometer. This allows a range of measurement-specific chemical and physical data to be recorded online and inline, which will contribute to a better understanding of fiber formation. In addition, a new compounder will be used for the development of functionalized polymers and for the energy-saving thermomechanical recycling of textile waste.

Texhibition Istanbul Fabric and Textile Accessories Fair, organised by İTKİB Fuarcılık A.Ş. in cooperation with the Istanbul Textile Exporters Association (İTHİB), is ready for its fifth edition. From 6 to 8 March 2024, 558 exhibitors will present themselves to the 30,000 expected visitors from over 100 countries, including the European Union, Great Britain, the USA, North Africa and the Middle East. With this edition, Texhibition has more than doubled the space compared to the last event to 35,000 square metres.

The fifth edition of Texhibition Istanbul offers a comprehensive overview of all product groups in the textile prepress sector: from woven fabrics to knitwear, from denim to artificial leather and textile accessories

Due to popular demand, the fair has been expanded to five halls, including the new Yarn Hall (Hall 8) with exhibitors such as Sasa, Aksa, Karafiber, Kortex, Tepar, Ensar, Kaplanlar and Iskur and the BlueBlack Denim Hall (Hall 7), which showcases the latest denim trends and presents a wide range from blue shades to black denims with exhibitors such as İsko, Çalık Bossa, Kipas and İskur. BlueBlack Denim is designed by the  designer Idil Tarzi in cooperation with the creative directors Gönül Altunisik and Selvi Yigci.

Curated by Idil Tarzi and her creative team, the Texhibition Trend Area in Halls 4 and 5 presents the latest colour trends, materials and accessories.

Under the direction of designers Arzu Kaprol and Filiz Tunca, the Innovation Hub showcases technological innovations that add value to textile production: from fibre to yarn, from fabrics to clothing.

Digital art installations in the entrance area, which run through the entire trade fair, as well as piano performances in the foyer await visitors at the upcoming Texhibition.

Seminars and workshops with industry experts shed light on current topics in the industry, including innovations, production processes and design developments. These opportunities offer participants a platform to exchange knowledge and discuss the latest developments in the textile industry.

INDA, the Association of the Nonwoven Fabrics Industry, announced the election of five new members to serve on its 2024 Board of Directors. The Board of Directors play a key role in advancing INDA’s strategic objectives, actively supporting both the industry and the membership. Their primary responsibility lies in ensuring that INDA remains responsive to the evolving needs of its members and the broader nonwovens industry, guiding the formulation of policies and programs.

The five new Board members include:

• Jaren J. Edwards, President, Stein Fibers
• Edward McNally, Sales Director Nonwoven, Oerlikon Nonwoven
• Thomas Olsen, Senior Vice President, Americas Business Area, Suominen
• Patricia A Sargeant, Vice President, Glatfelter Corporation
• Paul Wood, President, Ontex North America

The Board is comprised of elected Board Officers. One-third of the entire Board is elected each year for a three-year term by INDA’s general membership. INDA’s Executive Committee, empowered to act on behalf of the Board between meetings, consists of the Board Officers plus appointees.
The Executive Committee includes:

• Chair: Mark Thornton, Vice President, The Procter & Gamble Company
• Vice Chair: Barbara Lawless, VP of Sales and Marketing – Medical Products, Precision Fabrics Group, Inc.
• Past Chair: Bryan Haynes, Senior Technical Director for Global Nonwovens, Kimberly-Clark Corporation
• Appointee: Mike Clark, President, Filtration Solutions, Hollingsworth & Vose Company
• Appointee: Jodi Russell, Vice President R&D, Cleaning Innovation, Packaging & Sustainability, The Clorox Company
• Appointee: Jeff Stafford, Vice President of Nonwovens, Milliken & Company
• Appointee: Robert Weilminster, EVP & General Manager, US & Canada – Health, Hygiene and Specialties Division, Berry Global
• Appointee: Tom Zaiser, CEO, Indorama Ventures

Freudenberg Performance Materials (Freudenberg) is unveiling a new 100 percent synthetic wetlaid nonwoven product line made in Germany. The new materials can be manufactured from various types of polymer-based fibers, including ultra-fine micro-fibers, and are designed for use in filtration applications as well as other industrial applications.

Customers in the filtration business can use Freudenberg’s new fully synthetic wetlaid nonwovens in both liquid and air filtration. Applications include reverse osmosis membrane support, support for nanofibers or PTFE membranes as well as oil filtration media. The new materials are suited to use in the building & construction industry or the composites industry.
For filtration applications, the new fully synthetic wetlaid nonwovens are marketed under the Filtura® brand.

Versatile and flexible manufacturing
Freudenberg’s fully synthetic wetlaid nonwovens can be made of polyester, polyolefin, polyamide and polyvinyl alcohol (PVA), using staple fibers of up to 12mm fiber length and microfibers as fine as 0.04dtex. In terms of weight, the product range spans weights of between 8g/m² and 250g/m². Freudenberg’s flexible wetlaid manufacturing line has the capability to combine various thermal and chemical bonding technologies. The materials have high precision in weight and thickness as well as a defined pore size and high porosity.

Wetlaid capabilities for various applications
In addition to its fully synthetic range, Freudenberg can also incorporate glass fibers, viscose and cellulose. General industry applications for Freudenberg wetlaid nonwovens are surfacing veils for glass-fiber reinforced plastics, compostable desiccant bags, battery separators, acoustics, heatshields, and apparel applications such as embroidery substrates.

Fibre Extrusion Technology Ltd (FET) of Leeds, UK has appointed Dr Kristoffer Kortsen as Senior Materials and Process Scientist. He will report directly to R&D Manager, Dr Jonny Hunter, who joined FET in early 2023 in a growing Research and Development team.

Kortsen’s main area of work is in Gel Spinning of UHMWPE (Ultra-High Molecular Weight Polyethylene). His contribution will help provide gel spinning expertise and equipment in the near future to a range of industries including medical, aerospace, defence aerospace and marine.

He completed a Master’s in chemistry at KU Leuven, graduating magna cum laude in 2018. For his Master’s placement, he worked on the production of impact modifier additives for PVC at Kaneka Belgium. Continuing a partnership with this international chemical manufacturing company, he joined the Howdle group at the University of Nottingham for a PhD project looking into the industrial potential of scCO₂ dispersion polymerisations for additive production. After graduating, he worked in the Shaver group at the University of Manchester, developing a holistic approach to plastics recycling and sustainability across the many stakeholders in the field.

At this year's JEC World 2024 from 5 to 7 March, KARL MAYER GROUP will be exhibiting with KARL MAYER Technical Textiles and its STOLL Business

One focus of the exhibition will be non-crimp fabrics and tapes made from bio-based yarn materials for the reinforcement of composites.

"While our business with multiaxial and spreading technology for processing conventional technical fibres such as carbon or glass continues to do well, we are seeing increasing interest in the processing of natural fibres into composites. That's why we have a new product in our trade fair luggage for the upcoming JEC World: an alpine ski in which, among other things, hemp fibre fabrics have been used," reveals Hagen Lotzmann, Vice President Sales KARL MAYER Technische Textilien.

The winter sports equipment is the result of a subsidised project. The hemp tapes for this were supplied by FUSE GmbH and processed into non-crimp fabrics on the COP MAX 5 multiaxial warp knitting machine in the KARL MAYER Technical Textiles technical centre.

The STOLL Business Unit will be focussing on thermoplastic materials. Several knit to shape parts with a textile outer surface and a hardened inner surface will be on display. The double-face products can be made from different types of yarn and do not need to be back-moulded for use as side door panels or housing shells, for example. In addition, the ready-to-use design saves on waste and yarn material.