From the Sector

Reset
26 results
(c) A. Monforts Textilmaschinen GmbH & Co. KG
05.01.2024

Monforts: New Stenter line installed at Curt Bauer

Monforts' new Montex 8500 stenter line was recently installed at Curt Bauer’s plant in Aue in Germany.

Curt Bauer has been in continuous operation for 150 years, beginning as a weaving mill in Aue in the Ore Mountains region of Saxony back in 1882. Today, with 120 employees, the company has an annual production of 2.2 million metres of fabric and specialises in three key fields – home textiles, special damask fabrics for West African garments and technical textiles.

A first Montex stenter was installed by Monforts at the Aue plant in 2003 and an older machine from a third party supplier was also still in operation prior to the latest upgrade.
“The replacement of our older existing stenter, which was installed in 1985, was long overdue,” explains Gert Bauer. “It had a maximum working width of 2.2 metres and we were looking to both increase productivity and reduce energy requirements.”

Monforts' new Montex 8500 stenter line was recently installed at Curt Bauer’s plant in Aue in Germany.

Curt Bauer has been in continuous operation for 150 years, beginning as a weaving mill in Aue in the Ore Mountains region of Saxony back in 1882. Today, with 120 employees, the company has an annual production of 2.2 million metres of fabric and specialises in three key fields – home textiles, special damask fabrics for West African garments and technical textiles.

A first Montex stenter was installed by Monforts at the Aue plant in 2003 and an older machine from a third party supplier was also still in operation prior to the latest upgrade.
“The replacement of our older existing stenter, which was installed in 1985, was long overdue,” explains Gert Bauer. “It had a maximum working width of 2.2 metres and we were looking to both increase productivity and reduce energy requirements.”

As a consequence, the company opted for a new Montex 8500 line with a working width of 3.2 metres equipped with the MonforClean heat recovery and exhaust air purification system. The Montex stenter remains unmatched in terms of its robustness and long service life and with MonforClean technology, the waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required, compared to full gas and thermal oil heating. Overall energy savings of up to 40% can now be achieved compared to conventional stenters.

The first challenge at the Aue plant was how to fit the significantly larger machine into the available space without restricting the area required for docking operations.

The special multi-level configuration that Monforts designers and Curt Bauer’s team devised in order to meet these requirements involved raising all of the line’s drying zones – with a combined length of over 28 metres – on scaffolding platforms, to enable the ground floor space below them to continue to be fully utilised.

The next challenge involved configuring the MonforClean system without having to make any costly changes to the roofing structure. This, Gert Bauer observes, demanded “millimetre precision”.

With the new line now fully operational, the savings it is providing have yet to be fully calculated.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG

Monforts: Solid Success at ITMA 2023 Photo: Monforts / AWOL Media
07.07.2023

Monforts: Solid Success at ITMA 2023

Finishing machinery specialist Monforts has secured a number of major orders from textile manufacturers in Central and South America recently, and was pleased to welcome a high number of visitors from the region to its stand at ITMA 2023 in Milan from June 8-14.

Among new orders are those for three Montex stenters delivered to the AustralTex Group in Argentina and a further Montex range to denim manufacturer CIT in Brazil. Guatemala’s Global Textiles placed an order for its second Montex stenter, while Mexico’s Zentrix ordered its third and Avante, also in Mexico, has opted for its sixth.

Elsewhere, orders have also been placed for the delivery of three new Montex stenters to one of Pakistan’s major corporations, as well as a new Thermex dyeing range to nonwovens manaufacturer Orsa in Italy. Further orders – both for new machines and retrofit modules – are now anticipated following ITMA 2023, which attracted over 111,000 visitors to Milan.

Finishing machinery specialist Monforts has secured a number of major orders from textile manufacturers in Central and South America recently, and was pleased to welcome a high number of visitors from the region to its stand at ITMA 2023 in Milan from June 8-14.

Among new orders are those for three Montex stenters delivered to the AustralTex Group in Argentina and a further Montex range to denim manufacturer CIT in Brazil. Guatemala’s Global Textiles placed an order for its second Montex stenter, while Mexico’s Zentrix ordered its third and Avante, also in Mexico, has opted for its sixth.

Elsewhere, orders have also been placed for the delivery of three new Montex stenters to one of Pakistan’s major corporations, as well as a new Thermex dyeing range to nonwovens manaufacturer Orsa in Italy. Further orders – both for new machines and retrofit modules – are now anticipated following ITMA 2023, which attracted over 111,000 visitors to Milan.

“Visitor footfall at ITMA 2023 was well beyond the company’s expectations, and we were especially pleased at the constant number of visitors from South American companies, as well as from Asia and Europe,” said Monforts Marketing Manager Nicole Croonenbroek. “We were able to provide them with detailed information about our portfolio of machines and technologies digitally and fielded an unprecedented number of serious enquiries, many of which promise to turn into new business.”

Monforts Montex stenters for processes such as drying, stretching, heat-setting and coating, she added, are already the industry standard for the fabric finishing industry, providing a number of advantages in terms of production throughput and especially in energy efficiency and resource savings. Other key technologies in the Monforts portfolio include relaxation dryers, Thermex dyeing ranges and Monfortex compressive shrinking ranges.

Montex®Coat
“We were also very pleased with the interest in the Montex®Coat, the latest addition to our range of technologies, which we displayed in Milan,” Croonenbroek said.

The Montex®Coat can serve a very diverse number of markets and enables full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments, as well as solvent coatings. Knife coating, roller coating or screen printing can also all be accommodated with this system. It provides the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

Many refinements have been made to the Montex®Coat in the past few years, resulting in higher coating accuracy and the resulting quality of the treated fabrics. A number of advanced new improvements were introduced in Milan, including automatic edge limiters for immediately adapting to new coating widths and a new and simplified hand-held control device. These save considerable time in setting up the machine and ensuring consistent production.

The Montex®Coat unit displayed in Milan was sold to Vietnamese company Thai Tuan during the show.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG

(c) ITM/TUD
Herr Philipp Weigel, Preisträger des ITMA Sustainable Innovation Award - Research & Innovation Excellence  Award, auf dem Messestand des ITM auf der ITMA 2023
16.06.2023

Philipp Weigel erhält 1. Preis des ITMA Research & Innovation Excellence Award

Im Rahmen der diesjährigen ITMA 2023, der internationalen Textilmaschinenausstellung und Plattform für die gesamte Textilmaschinenbranche, die vom 08. bis 14. Juni 2023 in Mailand stattfand, wurde Herr Dipl.-Ing. Philipp Weigel für seine am ITM angefertigte exzellente Studienarbeit "Numerische Simulation des Struktur- und Auszugverhaltensparametrisch generierter profilierter Carbonpolymergarne" mit dem ITMA Sustainable Innovation Award in der Kategrie "Research & Innovation Excellence Award" ausgezeichnet. Er erhielt hierfür den 1. Preis, der mit 10.000 EUR dotiert ist.
 
Die Arbeit ist von großem wissenschaftlichen Interesse für die Entwicklung hochleistungsfähiger, ressourcenschonender Carbonbetonbauteile mit höchster Materialeffizienz und Nachhaltigkeit sowie für die simulative Beschreibung und digitale Auslegung der Bewehrungsstruktur.

CEMATEX-Präsident Ernesto Maurer überreichte das Preisgeld und Urkunde an die glücklichen Gewinner:nnen während der ITMA 2023 in Mailand, Italien.

Der 2. und 3. Preis ging an Absolventen des Instituts für Textiltechnik der RWTH Aachen.

Im Rahmen der diesjährigen ITMA 2023, der internationalen Textilmaschinenausstellung und Plattform für die gesamte Textilmaschinenbranche, die vom 08. bis 14. Juni 2023 in Mailand stattfand, wurde Herr Dipl.-Ing. Philipp Weigel für seine am ITM angefertigte exzellente Studienarbeit "Numerische Simulation des Struktur- und Auszugverhaltensparametrisch generierter profilierter Carbonpolymergarne" mit dem ITMA Sustainable Innovation Award in der Kategrie "Research & Innovation Excellence Award" ausgezeichnet. Er erhielt hierfür den 1. Preis, der mit 10.000 EUR dotiert ist.
 
Die Arbeit ist von großem wissenschaftlichen Interesse für die Entwicklung hochleistungsfähiger, ressourcenschonender Carbonbetonbauteile mit höchster Materialeffizienz und Nachhaltigkeit sowie für die simulative Beschreibung und digitale Auslegung der Bewehrungsstruktur.

CEMATEX-Präsident Ernesto Maurer überreichte das Preisgeld und Urkunde an die glücklichen Gewinner:nnen während der ITMA 2023 in Mailand, Italien.

Der 2. und 3. Preis ging an Absolventen des Instituts für Textiltechnik der RWTH Aachen.

Der ITMA Sustainable Innovation Award wurde von CEMATEX ins Leben gerufen, um die gemeinsamen Anstrengungen der globalen Textilindustrie zur Förderung der Nachhaltigkeit von Unternehmen durch innovative Lösungen und zur Förderung herausragender branchenspezifischer Forschung zu würdigen.
Der Preis umfasst zwei Kategorien: einen Industry Excellence Award für Textil- und Bekleidungshersteller und einen Research & Innovation Excellence Award, der für Master-Studenten offen ist.

Source:

Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) - TU Dresden

Photo A. Monforts Textilmaschinen GmbH & Co. KG
Gunnar Meyer
10.01.2023

Gunnar Meyer new Managing Director for Monforts

Gunnar Meyer has been assigned the new Managing Director of A. Monforts Textilmaschinen GmbH & Co. KG in Mönchengladbach, Germany, as of January 1st 2023.

He started his career with Monforts and has spent his whole working life in the textile machinery industry. Between 1985 and 2010 he was a key part of the Monforts team in various roles related to sales and commercial issues, including as General Sales Director. He returned to the company in 2019 after working for other well-known German textile machine manufacturers in the field of nonwovens.

“Working in other parts of the textile industry, I have gained a lot of experience in the management of complex technical textile projects and my special focus will certainly be on challenges like the current energy crisis, alternative heating systems and sustainable textile finishing,” stated Meyer.

Gunnar Meyer has been assigned the new Managing Director of A. Monforts Textilmaschinen GmbH & Co. KG in Mönchengladbach, Germany, as of January 1st 2023.

He started his career with Monforts and has spent his whole working life in the textile machinery industry. Between 1985 and 2010 he was a key part of the Monforts team in various roles related to sales and commercial issues, including as General Sales Director. He returned to the company in 2019 after working for other well-known German textile machine manufacturers in the field of nonwovens.

“Working in other parts of the textile industry, I have gained a lot of experience in the management of complex technical textile projects and my special focus will certainly be on challenges like the current energy crisis, alternative heating systems and sustainable textile finishing,” stated Meyer.

Source:

AWOL for A. Monforts Textilmaschinen GmbH & Co. KG (9912)

18.11.2022

Monforts at Igatex 2022

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts customers in the regions around the country’s three biggest cities of Karachi, Lahore and Faisalbad include all of the main players in the fields of home textiles and denim production, including Afroze, , Al Karam Artistic Milliners, Azgard-9, Crestex, , Gul Ahmed, Interloop, Liberty Mills, Lucky Textile Mills, Mustaqim, Naveena (NDL), Rajby Industries, Sapphire Finishing, Soorty, Style Textile and US Denim.

These companies rely on established Monforts technologies including Montex stentering equipment, Monfortex sanforizing units and Thermex dyeing ranges. The company’s Matex Eco Applicator minimum application system has also proved a big hit in recent years.

Monforts has also achieved considerable success in Pakistan with its Econtrol®* dyeing system  – an effective and established dyeing process. More than 40 Thermex continuous dyeing ranges have been installed in Pakistan in recent years and operator training on the Econtrol®* process by sophisticated technologists is an additional service.

The Econtrol® pad-dry process has a number of immediate benefits. Compared to the common pad-dry-pad-steam process, no salt is used and no steamer is required for a separate fixation step. Compared to the pad-dry-thermofix process, no urea is used and no smoke or deposits are generated, and unlike with the cold pad batch process, direct feedback of the dyeing results ensures no batching time is necessary and guarantees good reproducibility from the lab to bulk production.

An immediate wash off is also unnecessary, allowing for flexible production planning. The process is suitable for pale to dark shades with very good fastness properties. Also waste water treatment is improved by this technology.

*Econtrol is a registered mark of Dystar Colours Distribution GmbH.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

Dr. Harald Weber and Thomas Waldmann. Photo: VDMA
from left to right: Dr. Harald Weber and Thomas Waldmann.
08.11.2022

VDMA Textile Machinery Association: Dr Harald Weber succeeds Thomas Waldmann

Dr. Harald Weber will become the new managing director of the VDMA Textile Machinery Association on 1 January 2023. The 44-year-old industrial engineer succeeds Thomas Waldmann, who has held the position since 1991 and will retire at the end of the year.

After completing his doctorate at the Technical University of Darmstadt and working as a lecturer at the University of Applied Sciences Mittelhessen (THM), Dr. Weber joined the VDMA in 2011. Since then, he has been responsible for the topics of technology and innovation in the Plastics and Rubber Machinery Association.

Dr. Janpeter Horn, Chairman of the VDMA Textile Machinery Association and Managing Director of August Herzog Maschinenfabrik, commented on the change of personnel: "From his previous work in the plastics industry, Dr. Weber has profound knowledge and experience in topics that are also gaining in importance in textile machinery manufacturing. Examples include recycling and the circular economy, as well as digitalisation and especially the communication standard OPC UA."

Dr. Harald Weber will become the new managing director of the VDMA Textile Machinery Association on 1 January 2023. The 44-year-old industrial engineer succeeds Thomas Waldmann, who has held the position since 1991 and will retire at the end of the year.

After completing his doctorate at the Technical University of Darmstadt and working as a lecturer at the University of Applied Sciences Mittelhessen (THM), Dr. Weber joined the VDMA in 2011. Since then, he has been responsible for the topics of technology and innovation in the Plastics and Rubber Machinery Association.

Dr. Janpeter Horn, Chairman of the VDMA Textile Machinery Association and Managing Director of August Herzog Maschinenfabrik, commented on the change of personnel: "From his previous work in the plastics industry, Dr. Weber has profound knowledge and experience in topics that are also gaining in importance in textile machinery manufacturing. Examples include recycling and the circular economy, as well as digitalisation and especially the communication standard OPC UA."

Dr. Horn added: "We combine our warm welcome to Dr. Weber with a big thank you to Thomas Waldmann. 30 years as managing director at the Textile Machinery Association also stand for constantly changing framework conditions. Mr. Waldmann has always had his finger on the pulse of the industry and, together with his team, has represented the special interests of the member companies: From technology policy to challenges of market access to the leading trade fair ITMA and the European association CEMATEX. ITMA 2007 in Munich was certainly a highlight. The executive board of the association wishes Mr. Waldmann all the best for the new phase of his life that is now beginning."

Source:

VDMA e. V.
Textile Machinery

03.08.2022

17. Chemnitzer Textiltechnik-Tagung (CTT) am 28. + 29. September

Unter dem Motto „Textiltechnik als Schlüsseltechnologie der Zukunft“ informieren sich Maschinenproduzenten, Anwender, Textilfachleute und Forschende über neueste Entwicklungen in den Themenbereichen:

  • Ressourceneffiziente und nachhaltige Prozesse
  • Textiltechnologien für den Leichtbau
  • Digitalisierung in der textilen Produktion
  • Additive Fertigung mit Fasern und Textilien

Das Format bietet neben klassischen Vorträgen im Plenarteil und vier Themenkomplexen auch Pitches sowie studentische und wissenschaftliche Projektvorstellungen bzw. Exponate-Präsentationen.

Im Plenarteil der Veranstaltung werden der europäische GFK-Markt vorgestellt und die Bedeutung des Mittelstandes für die deutsche Volkswirtschaft näher beleuchtet.

Ausgewählte technologische Highlights der Fachvorträge in diesem Jahr sind neuartige Verfahren zum 3D-Druck, innovative Carbon-Textilien für die Betonarmierung sowie neue Digitalisierungsstrategien für den Maschinenbau und die Textilindustrie.

Kooperationspartner der diesjährigen Veranstaltung sind das tschechische Generalkonsulat und tschechische Branchenverbände.

Unter dem Motto „Textiltechnik als Schlüsseltechnologie der Zukunft“ informieren sich Maschinenproduzenten, Anwender, Textilfachleute und Forschende über neueste Entwicklungen in den Themenbereichen:

  • Ressourceneffiziente und nachhaltige Prozesse
  • Textiltechnologien für den Leichtbau
  • Digitalisierung in der textilen Produktion
  • Additive Fertigung mit Fasern und Textilien

Das Format bietet neben klassischen Vorträgen im Plenarteil und vier Themenkomplexen auch Pitches sowie studentische und wissenschaftliche Projektvorstellungen bzw. Exponate-Präsentationen.

Im Plenarteil der Veranstaltung werden der europäische GFK-Markt vorgestellt und die Bedeutung des Mittelstandes für die deutsche Volkswirtschaft näher beleuchtet.

Ausgewählte technologische Highlights der Fachvorträge in diesem Jahr sind neuartige Verfahren zum 3D-Druck, innovative Carbon-Textilien für die Betonarmierung sowie neue Digitalisierungsstrategien für den Maschinenbau und die Textilindustrie.

Kooperationspartner der diesjährigen Veranstaltung sind das tschechische Generalkonsulat und tschechische Branchenverbände.

Source:

Förderverein Cetex Chemnitzer Textilmaschinenentwicklung e.V.

(c) A. Monforts Textilmaschinen GmbH & Co. KG
07.07.2022

Monforts: New orders for machines at Techtextil 2022

The recent Techtextil show in Frankfurt emphasised the diversity of applications for nonwovens and technical textiles, according to finishing technology specialist Monforts.

“We fielded enquiries at top management level from an extremely wide range of companies, all with very different ideas for new product applications during the show,” said Alexander Fitz, who joined the company a year ago as engineer for textile technologies and co-ordinator of the Monforts Advanced Technology Centre (ATC). Fitz brings a background in both technical textile technology and processes to the role, having previously worked for a nonwovens machinery builder and a roll-goods manufacturer.

The recent Techtextil show in Frankfurt emphasised the diversity of applications for nonwovens and technical textiles, according to finishing technology specialist Monforts.

“We fielded enquiries at top management level from an extremely wide range of companies, all with very different ideas for new product applications during the show,” said Alexander Fitz, who joined the company a year ago as engineer for textile technologies and co-ordinator of the Monforts Advanced Technology Centre (ATC). Fitz brings a background in both technical textile technology and processes to the role, having previously worked for a nonwovens machinery builder and a roll-goods manufacturer.

Trials
“We are now looking forward to interesting new trials and pilot production runs, as well as the commissioning of new orders for machines resulting from the extremely busy exhibition,” he says. “Obviously, everyone at the moment is looking to make energy savings, and we have developed a range of options for helping companies increase their resource efficiency, both on new lines and as retrofitted systems, but this is not stifling innovation at the new material level.

“There was a lot of interest in what is possible with the Montex®Coat coating system and the range of different techniques it enables, and at our ATC in Mönchengladbach, a Montex®Coat unit is integrated into the full technical textiles pilot line, on which it is possible to run new fabrics in widths of up to 1.8 metres.”

Explosion proof
The technical textiles line at the ATC incorporates a Montex four-chamber stenter and is fitted with an explosion-proof coating application chamber in order to allow treatment to be carried out with organic solvents and other volatile materials.

Every single component within the chamber has to meet the standards of the European Union’s ATEX directives for working in a potentially explosive atmosphere. A range of sensors linked to alarms operate at various levels within the chamber to ensure the specified lower explosion limit (LOL) is never exceeded and the ventilation adapts accordingly.

Advanced functions
Special features on the finishing line relate to further advanced functions such as the ability to treat materials not only at temperatures of up to 320°C, but also to be able to treat the top and bottom faces of certain materials at different temperatures within a single pass through the machine.

To achieve this, the first two chambers of the stenter are fitted with special, heavy duty TwinAir ventilation motors and separate burners for individual top/bottom temperature. A temperature differential of up to 60°C can be achieved between the upper and lower nozzles within the chamber, depending on the treatment paramenters.

Another key feature of the technical textiles line at the ATC is the special stretching device which is capable of pulling ten tons in length and ten tons in width – a huge amount per square metre of fabric and necessary in the production of materials such as woven or 3D knits for high temperature filter media.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) ITM TUD
24.06.2022

VDMA verleiht Nachhaltigkeitspreise an Ingenieurnachwuchs am ITM

Die Verleihung der Förderpreise 2022 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchsingenieur:innen deutscher Universitäten für Spitzenleistungen im Studium fand am 22. Juni 2022 im Rahmen der Techtextil 2022 in Frankfurt/Main statt. Die bundesweit ausgeschriebenen Förderpreise wurden durch Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, auf dem VDMA-Messestand verliehen. Zum ersten Mal stand bei der Auswahl der eingereichten Arbeiten der Fokus auf Nachhaltigkeit.
 
Frau M. Sc. Marina Andrea Michel wurde mit dem mit 3.500 EUR dotierten Nachhaltigkeitspreis für die „Beste Masterarbeit des Deutschen Textilmaschinenbaues 2022“ geehrt. Ihre am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden Abschlussarbeit beschäftigt sich mit der „Funktionalisierung von Garnen mittels Cyclodextrinen zur Filtration von Mikro- und Nanoplastik, Übertragung auf Gewebe“.
 

Die Verleihung der Förderpreise 2022 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchsingenieur:innen deutscher Universitäten für Spitzenleistungen im Studium fand am 22. Juni 2022 im Rahmen der Techtextil 2022 in Frankfurt/Main statt. Die bundesweit ausgeschriebenen Förderpreise wurden durch Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, auf dem VDMA-Messestand verliehen. Zum ersten Mal stand bei der Auswahl der eingereichten Arbeiten der Fokus auf Nachhaltigkeit.
 
Frau M. Sc. Marina Andrea Michel wurde mit dem mit 3.500 EUR dotierten Nachhaltigkeitspreis für die „Beste Masterarbeit des Deutschen Textilmaschinenbaues 2022“ geehrt. Ihre am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden Abschlussarbeit beschäftigt sich mit der „Funktionalisierung von Garnen mittels Cyclodextrinen zur Filtration von Mikro- und Nanoplastik, Übertragung auf Gewebe“.
 
Im Fokus stand ein Verfahren zur textilchemischen Ausrüstung von Garn- und Gewebematerialien aus nachwachsenden Rohstoffen mit Cyclodextrinen, die Mikro- und Nanoplastik (MNP) anbinden. Die grundlegenden Erkenntnisse zeigen dabei das Potenzial daraus hergestellter faserbasierter Filter zur deutlichen und nachhaltigen Minimierung der MNP-Belastung, sowohl von lokalen Trinkwasserquellen bis hin zu globalen Wasserkreisläufen, auf. Die Masterarbeit beinhaltet erstmals die innovative Anwendung von Cyclodextrinmolekülen zur Anbindung kleinster Plastikpartikel unterschiedlicher Form und molekularer Zusammensetzung.
 
Simon Hoebel erhielt den mit 3.000 EUR dotierten Nachhaltigkeitspreis „Beste Forschungsarbeit des Deutschen Textilmaschinenbaues 2022“ über die „Weiterentwicklung des Versuchstandes zur Herstellung von flexiblen hochdrapierbaren Thermoplastfaserbandstrukturen aus recycelten Carbonfasern und Thermoplastfasern für hochbelastbare thermoplastische Verbundbauteile“.
 
Das Ziel der prämierten Forschungsarbeit bestand in der Weiterentwicklung eines Versuchstandes sowie eines anwendungsbezogenen technologischen Knowhows zur Entwicklung und Fertigung von unidirektionalen hochdrapierbaren Thermoplastfaserbandstrukturen aus recycelten Carbonfasern (rCF) und Thermoplastfasern (TFS) für hochbelastbare thermoplastische CFK-Bauteile. Im Rahmen der Forschungsarbeit untersuchte Hoebel den gesamten Prozess zur Herstellung von hochdrapierbaren Thermoplastfaserbandstrukturen von der Kardierung, Verstreckung, Banddoublierung und Konsolidierung. Aus den entwickelten rCF-TFS wurden thermoplastische UD-Verbunde gefertigt und ihre mechanischen Eigenschaften charakterisiert. Die Ergebnisse der Studienarbeit zeigen das Potenzial dieser neuartigen Prozesskette und der darauf basierenden leistungsfähigen und nachhaltigen Thermoplastfaserbandstrukturen auf Basis von rCF.

Source:

Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

(c) A. Monforts Textilmaschinen GmbH & Co. KG
20.06.2022

Monforts introduces range of modular upgrades

Monforts is introducing a range of modular upgrades that can be added to existing finishing lines already in production.

The Monforts universal Energy Tower – a flexible, free-standing air/air heat exchanger for recovering the heat from the exhaust air flow of thermal processes – can result in a 30% reduction in the energy consumed by a line, depending on the exhaust air volume and operating temperature.

A Monforts Eco Booster, completely integrated into the chamber design of the Montex stenter, is another retrofitting option. As a single state-of-the-art heat recovery system with automatic cleaning, it can be added to existing ranges. For ranges of up to eight chambers only one module is necessary to achieve significant energy savings.

On an eight-chamber stenter with an operating width of two metres carrying out a fixing process on a 150gsm woven fabric, for example, the energy savings have been calculated to be 35% over an annual schedule of 6,000 operating hours.

In addition, the Eco Booster consumes only minimal amounts of water during the cleaning cycle and the entire process is controlled and monitored automatically.

Monforts is introducing a range of modular upgrades that can be added to existing finishing lines already in production.

The Monforts universal Energy Tower – a flexible, free-standing air/air heat exchanger for recovering the heat from the exhaust air flow of thermal processes – can result in a 30% reduction in the energy consumed by a line, depending on the exhaust air volume and operating temperature.

A Monforts Eco Booster, completely integrated into the chamber design of the Montex stenter, is another retrofitting option. As a single state-of-the-art heat recovery system with automatic cleaning, it can be added to existing ranges. For ranges of up to eight chambers only one module is necessary to achieve significant energy savings.

On an eight-chamber stenter with an operating width of two metres carrying out a fixing process on a 150gsm woven fabric, for example, the energy savings have been calculated to be 35% over an annual schedule of 6,000 operating hours.

In addition, the Eco Booster consumes only minimal amounts of water during the cleaning cycle and the entire process is controlled and monitored automatically.

The Matex Eco Applicator is an alternative to the conventional padding process for energy-conscious finishing and achieving considerable savings in the energy required for drying treated fabrics. The precise amount of chemical can be applied to the fabric and with less residual moisture after application of only approximately 35% so that less drying capacity is required in the stenter, which leads to huge energy savings.

Finishes can be evenly applied on either or both sides of the fabric, and two separate treatments can be applied to front and back. This makes the unit ideal for the production of, for example, double-performance hydrophobic/hydrophilic fabrics for professional clothing, as well as the over dyeing or finishing of denim fabrics.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) A. Monforts Textilmaschinen GmbH & Co. KG
07.04.2022

Montex stenter at ITM

Monforts and its Turkish representative Neotek are looking forward to the forthcoming ITM 22 international textile machinery show taking place from June 14-18 at the Tüyap Fair and Congress Centre in Istanbul, after a three-year break.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying. The resulting constant evaporation rate within the stenter ensures optimum energy utilisation and also avoids markings on the fabric.

With the latest Montex stenters, overall energy savings of up to 40% can now be achieved compared to a conventional stenter with no heat recovery or energy optimisation measures like high-quality chamber insulation.

Monforts and its Turkish representative Neotek are looking forward to the forthcoming ITM 22 international textile machinery show taking place from June 14-18 at the Tüyap Fair and Congress Centre in Istanbul, after a three-year break.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying. The resulting constant evaporation rate within the stenter ensures optimum energy utilisation and also avoids markings on the fabric.

With the latest Montex stenters, overall energy savings of up to 40% can now be achieved compared to a conventional stenter with no heat recovery or energy optimisation measures like high-quality chamber insulation.

The Montex stenter also benefits from full digital control, with the Qualitex 800 PLC control system providing ease of operation and rapid access to line and management data, including full operating cost overviews, as well as maintenance monitoring.

Advances in digital technology mean that there are also now significant gains to be made in the retrofitting of existing Monforts machines with the latest automatic drives and control systems, going far beyond the basic replacement of spare parts.

“We will be emphasising the robustness and versatility of the Montex stenter for essential processes such as drying, stretching, heatsetting and coating at the Istanbul show,” said Monforts Area Sales Manager Thomas Päffgen.

“With energy prices rising steeply everywhere, features such as the MonforClean system, or the EcoBooster, in which waste heat from the drying process is used to pre-heat the drying air, are proving more invaluable than ever,” added Ahmet Kilic of Neotek. “Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation.”

Source:

A. Monforts Textilmaschinen GmbH & Co. KG

Hochschule Albstadt-Sigmaringen: Textile Studiengänge verfügen über neue Maschinentypen (c) Hochschule Albstadt-Sigmaringen
Der Masterstudent Marc Weisser und Marc Witzemann am neuen Etikettierer
01.04.2022

Hochschule Albstadt-Sigmaringen: Neue Maschinentypen für textile Studiengänge

In den Laboren der textilen Studiengänge an der Hochschule Albstadt-Sigmaringen stehen pünktlich zum Start ins Sommersemester zwei brandneue Maschinen, die den Studierenden ebenso zur Verfügung stehen wie Interessierten aus der Textilindustrie.

„Wir testen gerade den Prototypen einer Flüssigklebemaschine“, sagt Prof. Matthias Kimmerle. Dabei handelt es sich um eine Weltneuheit, die es bislang noch nirgendwo sonst gibt – möglich wurde diese Leihgabe durch die hervorragenden Kontakte der Hochschule zum japanischen Hersteller. Das Neue daran: Anstatt Kleidung zu nähen, werden die einzelnen Schnittteile geklebt. „Die Ergebnisse sind sehr überzeugend“, sagt Matthias Kimmerle. „Die Kantenführung erledigt die Maschine vollautomatisch und hält dabei die Abstände exakt und konstant ein.“

In den Laboren der textilen Studiengänge an der Hochschule Albstadt-Sigmaringen stehen pünktlich zum Start ins Sommersemester zwei brandneue Maschinen, die den Studierenden ebenso zur Verfügung stehen wie Interessierten aus der Textilindustrie.

„Wir testen gerade den Prototypen einer Flüssigklebemaschine“, sagt Prof. Matthias Kimmerle. Dabei handelt es sich um eine Weltneuheit, die es bislang noch nirgendwo sonst gibt – möglich wurde diese Leihgabe durch die hervorragenden Kontakte der Hochschule zum japanischen Hersteller. Das Neue daran: Anstatt Kleidung zu nähen, werden die einzelnen Schnittteile geklebt. „Die Ergebnisse sind sehr überzeugend“, sagt Matthias Kimmerle. „Die Kantenführung erledigt die Maschine vollautomatisch und hält dabei die Abstände exakt und konstant ein.“

Ein Wäschehersteller aus Albstadt hat die Maschine bereits erfolgreich ausprobiert, „und wir selber testen sie mit Funktionsmaterialien, wie sie bei Unterwäsche oder Sportkleidung benutzt werden“. Hier seien störende Nähte häufig unerwünscht, und die Klebetechnik kann genau dieses Problem lösen. Die Maschine steht noch ein paar Wochen in Albstadt zur Verfügung, bevor sie zu einem Textilunternehmen nach Österreich umzieht.

In der Lernfabrik der textilen Studiengänge steht außerdem seit vergangener Woche der Prototyp eines neuen Etikettierers (angedockt an einen Zünd-Cutter), der die Schnittteile nach dem Ausschneiden automatisch etikettieren kann. Eine solche Maschine sei für viele Branchen nützlich, „insbesondere dann, wenn in der Produktion viele Teile hergestellt werden, die sich ähneln“, sagt Matthias Kimmerle. Ermöglicht wurde die Anschaffung durch Marc Witzemann, Geschäftsführer von Rebstock Consulting, der die Maschinen des Herstellers in Deutschland vertreibt und die Hochschule seit Jahren mit der Dauerleihgabe von Cuttern unterstützt. „Es ist uns ein großes Anliegen, dass Studierende und kleinere Unternehmen die Möglichkeit bekommen, auf neuer Technik etwas zu testen“, sagt er. Wie wichtig genau das im sehr praxisbezogenen Studium an der Hochschule ist, betont auch Matthias Kimmerle. „Die Maschine passt zudem perfekt zu unserer Microfactory.“ Diese ermöglicht es, selbst kleine Losgrößen von nur einem Stück auf Kundenwünsche angepasst herzustellen.

Source:

Hochschule Albstadt-Sigmaringen

(c) VDMA
Chairperson and Vice Chairpersons of the VDMA Textile Machinery: Verena Thies, Dr. Janpeter Horn, Regina Brückner.
31.03.2022

VDMA: Dr. Janpeter Horn New Chairperson of Textile Machinery Association

Dr. Janpeter Horn, Managing Director of August Herzog Maschinenfabrik, is the new Chairperson of the VDMA Textile Machinery. Dr. Horn was elected at the members’ meeting of the Association in Leonberg. The new Executive Board is completed with Ms. Regina Brückner, Managing Associate of Brückner Trockentechnik and Ms. Verena Thies, Managing Shareholder of Thies Textilmaschinen, who were elected as Vice Chairpersons.

After his election, Dr. Horn stated: “I am pleased to have Ms. Brückner and Ms. Thies by my side. Both have been serving on the Executive Board of the VDMA Textile Machinery as well as the European Committee of Textile Machinery Manufacturers CEMATEX for many years. With this team, we are well prepared to effectively represent the interests of the industry at national and international level.”

Based in Oldenburg, Northern Germany, Herzog is a company with a long tradition and at the same time the most innovative developer and manufacturer of braiding and winding machinery. Worldwide references in braiding and winding technique confirm the company’s technical and quality leadership.

Dr. Janpeter Horn, Managing Director of August Herzog Maschinenfabrik, is the new Chairperson of the VDMA Textile Machinery. Dr. Horn was elected at the members’ meeting of the Association in Leonberg. The new Executive Board is completed with Ms. Regina Brückner, Managing Associate of Brückner Trockentechnik and Ms. Verena Thies, Managing Shareholder of Thies Textilmaschinen, who were elected as Vice Chairpersons.

After his election, Dr. Horn stated: “I am pleased to have Ms. Brückner and Ms. Thies by my side. Both have been serving on the Executive Board of the VDMA Textile Machinery as well as the European Committee of Textile Machinery Manufacturers CEMATEX for many years. With this team, we are well prepared to effectively represent the interests of the industry at national and international level.”

Based in Oldenburg, Northern Germany, Herzog is a company with a long tradition and at the same time the most innovative developer and manufacturer of braiding and winding machinery. Worldwide references in braiding and winding technique confirm the company’s technical and quality leadership.

The new Executive Board of the VDMA Textile Machinery for the legislative period until 2026 is composed of:

  • Dr. Janpeter Horn (Chairperson), August Herzog Maschinenfabrik
  • Regina Brückner (Vice Chairperson), BRÜCKNER Trockentechnik
  • Verena Thies (Vice Chairperson), THIES
  • Peter D. Dornier, Lindauer DORNIER
  • Stefan Flöth, A. Monforts Textilmaschinen
  • Arno Gärtner, KARL MAYER STOLL Textilmaschinenfabrik
  • Markus Kleindorp, MEMMINGER-IRO
  • Andreas Lukas, ANDRITZ Küsters
  • Benjamin Mayer, Mayer & Cie.
  • Dr. Jörg Morgner, Temafa Maschinenfabrik
  • Benjamin Reiners, Reiners + Fürst
  • Dr. Uwe Rondé, Saurer Group
  • Eric Schöller, Groz-Beckert
  • Georg Stausberg, Oerlikon Textile
  • Heinrich Trützschler, Trützschler Group
Source:

VDMA e. V.
Textilmaschinen

31.03.2022

Monforts at Techtextil North America

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Advanced machine operation
With the highly intuitive Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Versatility is the key
Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

Source:

AWOl Media / A. Monforts Textilmaschinen GmbH & Co. KG

ANDRITZ delivers tearing line to Sasia Photo: ANDRITZ
Miguel Silva, CEO of Sasia, in front of the newly installed seven-cylinder Jumbo tearing line
15.02.2022

ANDRITZ delivers tearing line to Sasia

In January 2022, international technology group ANDRITZ successfully started up its latest-generation tearing line for spinning grade fibers delivered to Sasia at its Ribeirão premises, Portugal.

The scope of supply includes a seven-cylinder Jumbo tearing machine dedicated to spinning grade fibers. As the first of its kind in Portugal, the machine contains the latest ANDRITZ Laroche innovation for fiber opening, featuring a new-generation pinning configuration.

ANDRITZ has worked closely with Sasia for more than half a century, offering both cutting-edge solutions for recycling as well as every possible fine-tuning customization to support Sasia’s goals. Sasia’s plant now has four state-of-the-art ANDRITZ Laroche tearing lines.

A pioneer in the textile recycling industry since its foundation in 1952, Sasia is engaged in the circular economy with the aim of reducing textile waste by turning it into usable raw material again, increasing ability to compete as well as promoting innovation and sustainability.

In January 2022, international technology group ANDRITZ successfully started up its latest-generation tearing line for spinning grade fibers delivered to Sasia at its Ribeirão premises, Portugal.

The scope of supply includes a seven-cylinder Jumbo tearing machine dedicated to spinning grade fibers. As the first of its kind in Portugal, the machine contains the latest ANDRITZ Laroche innovation for fiber opening, featuring a new-generation pinning configuration.

ANDRITZ has worked closely with Sasia for more than half a century, offering both cutting-edge solutions for recycling as well as every possible fine-tuning customization to support Sasia’s goals. Sasia’s plant now has four state-of-the-art ANDRITZ Laroche tearing lines.

A pioneer in the textile recycling industry since its foundation in 1952, Sasia is engaged in the circular economy with the aim of reducing textile waste by turning it into usable raw material again, increasing ability to compete as well as promoting innovation and sustainability.

This order not only underlines ANDRITZ’s position as the leading supplier worldwide of textile recycling lines, but also highlights its ability to bring continuous improvement with sustainable solutions and versatility to its customers.

Source:

ANDRITZ AG

(c) Monforts / AWOL Media
07.02.2022

Monforts: Turkish upholstery leader opts for the Montex®Coat

Turkish powerhouse in home textiles and furnishing fabrics Altun Tekstil has just commissioned the first Montex®Coat coating system in Turkey.

The advanced machine has been installed at the ever-expanding family-owned company’s industrial complex in Bursa and is being employed to provide an anti-slip and textured backing to upholstery fabrics with a stable and uniform foam, via knife-over-roller coating.  

Founded in 1993, Altun exports its fabrics to more than 60 countries, with its major export markets being Russia and Ukraine, as well as many Middle Eastern and European countries.
Its integrated operations include the production of texturized yarns, weaving and raschel knitting, in addition to dyeing and finishing. With a major focus on tulle curtains and upholstery, the company’s fabric range also extends to a wide variety of apparel styles.

Turkish powerhouse in home textiles and furnishing fabrics Altun Tekstil has just commissioned the first Montex®Coat coating system in Turkey.

The advanced machine has been installed at the ever-expanding family-owned company’s industrial complex in Bursa and is being employed to provide an anti-slip and textured backing to upholstery fabrics with a stable and uniform foam, via knife-over-roller coating.  

Founded in 1993, Altun exports its fabrics to more than 60 countries, with its major export markets being Russia and Ukraine, as well as many Middle Eastern and European countries.
Its integrated operations include the production of texturized yarns, weaving and raschel knitting, in addition to dyeing and finishing. With a major focus on tulle curtains and upholstery, the company’s fabric range also extends to a wide variety of apparel styles.

Altun has installed eight stenters in various widths at its two plants since 2016 – coincidentally the year Monforts Turkish representative Neotek was founded. All of the stenters are engineered for specific product lines and the Montex®Coat unit is integrated into the latest of these lines, which has a maximum working width of 2.2 metres and eight chambers.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

06.01.2022

Monforts presents Econtrol® at VDMA Webtalk in February

Monforts textile technologist Jonas Beisel will outline the benefits of the company’s Econtrol® continuous dyeing process during the next free-to-attend VDMA Textile Machinery Webtalk which takes place on February 3rd 2022 at 13.00 (CET).

“Our customers are increasingly looking at shorter production runs and the more economical use of dyestuffs, as well as reducing water and energy consumption,” says Beisel. “We have gained many years of experience in the optimisation of dyeing processes through working with our customers, both at their own plants and in our Advanced Technology Centre (ATC) in Mönchengladbach, Germany.

“Our Thermex universal hotflue for continuous dyeing, curing and thermosoling achieves unrivalled reliability even at high fabric speeds, for exceptional cost-effectiveness when dyeing both large and small batches of woven fabrics. The Econtrol® process for reactive dyestuffs now has an impressive number of references on the market, as a quick and economical one-pass pad-dry and wash off process. This is the ideal process for fast change technology and operational savings.”

Monforts textile technologist Jonas Beisel will outline the benefits of the company’s Econtrol® continuous dyeing process during the next free-to-attend VDMA Textile Machinery Webtalk which takes place on February 3rd 2022 at 13.00 (CET).

“Our customers are increasingly looking at shorter production runs and the more economical use of dyestuffs, as well as reducing water and energy consumption,” says Beisel. “We have gained many years of experience in the optimisation of dyeing processes through working with our customers, both at their own plants and in our Advanced Technology Centre (ATC) in Mönchengladbach, Germany.

“Our Thermex universal hotflue for continuous dyeing, curing and thermosoling achieves unrivalled reliability even at high fabric speeds, for exceptional cost-effectiveness when dyeing both large and small batches of woven fabrics. The Econtrol® process for reactive dyestuffs now has an impressive number of references on the market, as a quick and economical one-pass pad-dry and wash off process. This is the ideal process for fast change technology and operational savings.”

Among key benefits are the saving of resources compared to conventional continuous dyeing methods, excellent reproducibility of pale to dark shades, from lab to bulk, and greater flexibility in production planning due to a resulting dry fabric that does not need an immediate wash off.

Econtrol® is a registered trademark of DyStar® Colours Distribution GmbH, Germany, and Bertram Seuthe of DyStar® will be providing recommendations for dyes and auxiliaries for the process during the VDMA event.

A third speaker, Guido Seiler of Fong’s Europe, will explain how Goller washing ranges help to significantly reduce the water that is conventionally wasted in the washing off process, through a combination of process and chemistry know-how and advanced technologies.

More information:
Monforts VDMA Textilmaschinen
Source:

Monforts Textilmaschinen GmbH & Co. KG by AWOL Media

16.11.2021

DECHOW versteigert Maschinen und Anlagen der SR Webatex GmbH in Bayreuth

  • Nach Werksschließung: Inventar der modernen Textilweberei wird online bis zum 09. Dezember versteigert

DECHOW, eines der marktführenden Industrie-Auktionshäuser in Europa, verantwortet die Vermarktung der Textilweberei SR Webatex GmbH in Bayreuth. Rund 700 Lose kommen, bei der reinen Online-Auktion auf www.troostwijkauctions.com, vom 18. November bis 09. Dezember 2021 zum Aufruf. Darunter 46 DORNIER DLW Luftwebmaschinen der Baujahre 1999-2019 und 43 PICANOL Luftwebmaschinen der Baujahre 2007 – 2011.

  • Nach Werksschließung: Inventar der modernen Textilweberei wird online bis zum 09. Dezember versteigert

DECHOW, eines der marktführenden Industrie-Auktionshäuser in Europa, verantwortet die Vermarktung der Textilweberei SR Webatex GmbH in Bayreuth. Rund 700 Lose kommen, bei der reinen Online-Auktion auf www.troostwijkauctions.com, vom 18. November bis 09. Dezember 2021 zum Aufruf. Darunter 46 DORNIER DLW Luftwebmaschinen der Baujahre 1999-2019 und 43 PICANOL Luftwebmaschinen der Baujahre 2007 – 2011.

„Die SR Webatex GmbH war auf die Produktion von technischen Textilien und Gewebelösungen spezialisiert“, erklärt Eva Traut, Projektleiterin AUKTIONSHAUS WILHELM DECHOW GmbH. „Bei den Auktions-Losen handelt es um einen überdurchschnittlich modernen Maschinenbestand, der sich darüber hinaus in einem außergewöhnlich guten und gepflegten Erhaltungszustand befindet“, so Traut weiter. Als neuwertig können bespielweise eine Schlichtmaschine vom Typ KARL MAYER Prosize PSZ (Baujahr 2018) und eine Kontroll- und Wickelmaschine vom Typ RAUCH CB-WK/BA (Baujahr 2019) bezeichnet werden. Viele weitere Spezialmaschinen wie automatische Fadeneinzugsmaschinen und Muster-, Sektional- sowie Kegelbaumschärmaschinen oder ein Labor mit u.a. Garnprüfmaschine, Zugprüfgerät, Waagen und vielen Mikroskopen sind ebenfalls Bestandteil der Auktion.

Zahlreiche Lose dürften auch für Unternehmen in Bayreuth und Umgebung von Interesse sein, wie z.B. die STILL und LINDE Gabelstapler oder die Werkstattausrüstung mit Drehbank, Radialbohr- und Sägemaschinen.

Kaufinteressenten können sich direkt vor Ort einen Eindruck verschaffen. Der Besichtigungstermin findet am 07. Dezember 2021 von 10:00 – 14:00 Uhr in der Tunnelstraße 6, 95448 Bayreuth statt. Interessenten melden sich bitte vorab unter support@dechow.de an.

More information:
Auktion Textilmaschinen
Source:

bereuter media

© ITM / TU Dresden
10.11.2021

Kreativitätspreis des Deutschen Textilmaschinenbaues 2021 geht an Irina Kuznik

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Frau Dipl.-Ing. Irina Kuznik vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden wurde mit dem 3.000 EUR dotierten Kreativitätspreis des Deutschen Textilmaschinenbaues 2021 für ihre exzellente Diplomarbeit „Entwicklung zur umweltfreundlichen Herstellung neuartiger Chitosanfasergarne unter Einsatz von ionischen Flüssigkeiten" ausgezeichnet.

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Frau Dipl.-Ing. Irina Kuznik vom Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM) der TU Dresden wurde mit dem 3.000 EUR dotierten Kreativitätspreis des Deutschen Textilmaschinenbaues 2021 für ihre exzellente Diplomarbeit „Entwicklung zur umweltfreundlichen Herstellung neuartiger Chitosanfasergarne unter Einsatz von ionischen Flüssigkeiten" ausgezeichnet.

In ihrer Diplomarbeit entwickelte Frau Kuznik einen völlig neuen Ansatz zur ökologischen und ökonomischen Herstellung von Chitosangarnen. Unter Nutzung ionischer Flüssigkeiten als gut geeignetes, neuartiges Lösungsmittel für Chitosan lässt sich Chitosan mit geringen Deacetylierungsgraden sowie reines Chitin erfolgreich auflösen. In einem Nassspinnverfahren können damit erzeugte Spinnlösungen zu neuartigen Chitosan- bzw. Chitinmonofilamenten mit sehr guten morphologischen Eigenschaften hergestellt werden. Des Weiteren lässt sich die ionische Flüssigkeit mittels eines Verdampfungsverfahrens aus dem Abwasser zurückgewinnen und wiederaufbereitet werden.

More information:
VDMA Textilmaschinen chitosan
Source:

Technische Universität Dresden
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)

(c) ITM/TU Dresden
10.11.2021

Förderpreis beste Dissertation des Deutschen Textilmaschinenbaues 2021 an Dr.-Ing. Martin Hengstermann

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Dr.-Ing. Martin Hengstermann wurde mit dem mit 5.000 EUR dotierten Förderpreis beste Dissertation des Deutschen Textilmaschinenbaues 2021 für seine am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden erarbeiteten Dissertation „Entwicklung von Hybridgarnen aus recycelten Carbonfasern und Polyamid 6-Fasern für thermoplastische Verbundbauteile mit hohem Leistungsvermögen“ geehrt.

Die Verleihung der Förder- und Kreativitätspreise 2021 der Walter Reiners-Stiftung des VDMA, Fachverband Textilmaschinen an Studierende und Nachwuchswissenschaftler:innen deutscher Universitäten für Spitzenleistungen in Studium und Promotion fand am 09. November 2021 im Rahmen der Aachen-Dresden-Denkendorf International Textile Conference 2021 statt. Die bundesweit ausgeschriebenen Förder- und Kreativitätspreise wurden erneut online durch Herrn Peter D. Dornier, Vorstandsvorsitzender der Walter Reiners-Stiftung, verliehen.

Dr.-Ing. Martin Hengstermann wurde mit dem mit 5.000 EUR dotierten Förderpreis beste Dissertation des Deutschen Textilmaschinenbaues 2021 für seine am Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik der TU Dresden erarbeiteten Dissertation „Entwicklung von Hybridgarnen aus recycelten Carbonfasern und Polyamid 6-Fasern für thermoplastische Verbundbauteile mit hohem Leistungsvermögen“ geehrt.

Gegenstand der Dissertation ist die Entwicklung und Umsetzung von neuartigen Hybridgarnen aus recycelten Carbonfasern (rCF) und Polyamid (PA) 6-Fasern für thermoplastische Verbundbauteile. Diese Hybridgarne können die hervorragenden mechanischen Eigenschaften der rCF im Gegensatz zu bisherigen Lösungen in hohem Maße ausnutzen. Bedingt durch deren spezielle Fasereigenschaften (insbesondere hohe Querkraftempfindlichkeit, Sprödigkeit und fehlende Kräuselung) wurde dafür die Prozesskette der konventionellen Stapelfasergarnherstellung, bestehend aus Krempel, Strecke und Flyer, umfangreich analysiert und technologisch-konstruktiv weiterentwickelt, wodurch erstmalig eine schonende und gleichmäßige Herstellung der Hybridgarne ermöglicht werden konnte.

Source:

Technische Universität Dresden
Institut für Textilmaschinen und Textile Hochleistungswerkstofftechnik (ITM)