From the Sector

Reset
9 results
19.07.2022

Rieter starts sales process for the remaining land owned by Rieter

  • Order intake of CHF 869.4 million, order backlog of more than CHF 2 100 million
  • Sales of CHF 620.6 million, preproduced deliveries in the three-digit million range had to be postponed until the second half of 2022
  • EBIT of CHF -10.2 million, net result of CHF -25.2 million due to significant cost increases, additional costs, and acquisition-related expenses
  • Action plan to increase sales and profitability
  • Rieter site Winterthur
  • Outlook

Rieter continued to be successful in the market in the first half of 2022. Based on the company’s technology leadership, innovative product portfolio and the completion of the ring- and compact-spinning system, a high order intake and a significant increase in sales were generated. The increase in sales was achieved even though preproduced deliveries in the three-digit million range had to be postponed until the second half of 2022. The order backlog is at a record level.

  • Order intake of CHF 869.4 million, order backlog of more than CHF 2 100 million
  • Sales of CHF 620.6 million, preproduced deliveries in the three-digit million range had to be postponed until the second half of 2022
  • EBIT of CHF -10.2 million, net result of CHF -25.2 million due to significant cost increases, additional costs, and acquisition-related expenses
  • Action plan to increase sales and profitability
  • Rieter site Winterthur
  • Outlook

Rieter continued to be successful in the market in the first half of 2022. Based on the company’s technology leadership, innovative product portfolio and the completion of the ring- and compact-spinning system, a high order intake and a significant increase in sales were generated. The increase in sales was achieved even though preproduced deliveries in the three-digit million range had to be postponed until the second half of 2022. The order backlog is at a record level. Despite higher sales, the significant increase in material and logistics costs, additional costs for compensation of the material shortages and the expenditure incurred for the acquisition in the years 2021/2022 resulted in a loss. Rieter is implementing an action plan to increase sales and profitability. The sales process for the remaining land owned by Rieter was initiated.

Order Intake and Order Backlog
Rieter posted an order intake of CHF 869.4 million, which included CHF 176.6 million from the businesses acquired in the years 2021/2022. As expected, demand has thus returned to normal compared with the exceptionally high figure for the prior-year period, but remains well above the average figure for the last five years of around CHF 570 million (first half 2021: CHF 975.3 million, first half 2022 excluding acquisition effect CHF 692.8 million).

The regional shift in demand with investments in additional spinning capacity outside China along with investments in the competitiveness of Chinese spinning mills continues. Rieter benefits from its technology leadership, the innovative product portfolio and the completion of the ring- and compact-spinning system through the acquisition of the automatic winding machine business. The largest order intakes came from India, Turkey, China, Uzbekistan, and Pakistan.

On June 30, 2022, the company had an order backlog of more than CHF 2 100 million (June 30, 2021: CHF 1 135 million). Cancellations in the reporting period amounted to around 5% of the order backlog.

Sales
The Rieter Group posted sales of CHF 620.6 million, which included CHF 68.9 million from the businesses acquired in the years 2021/2022 (first half 2021: CHF 400.5 million).

As a result, sales were significantly higher than in the prior-year period, although preproduced deliveries, which mainly affected the Business Group Machines & Systems, in the three-digit million range had to be postponed until the second half of 2022. The reasons for the postponements were the COVID lockdown in China and supply chain bottlenecks.

EBIT, Net Result and Free Cash Flow
Rieter posted a loss of CHF -10.2 million at the EBIT level in the first half of 2022.

Earnings were impacted by significantly higher material and logistics costs. The price increases already implemented are having a delayed effect, mainly in the Business Group Machines & Systems, and were therefore unable to compensate for the high increase in costs. In addition, costs in connection with material shortages negatively impacted profitability. The result also includes acquisition-related expenses of CHF -11.2 million.

The loss at the net result level was CHF -25.2 million, of which CHF -17.6 million was due to the acquisition.

Free cash flow was CHF -57.1 million, attributable to the build-up of inventories in connection with the high order backlog and postponed deliveries.

Action Plan to Increase Sales and Profitability
Rieter is implementing a comprehensive package of measures with the aim of increasing sales and profitability in the second half of 2022.

The package focuses on two main priorities: Firstly, Rieter is continuing to systematically implement price increases while working to improve the quality of margins of the order backlog, so as to compensate for cost increases in materials and logistics.
Secondly, Rieter is working closely with key suppliers and is developing alternative solutions to eliminate material bottlenecks, as far as possible, in order to safeguard deliveries.

Rieter Site Winterthur
The Board of Directors has decided to begin the process for the sale of the remaining land at the Rieter site in Winterthur (Switzerland). In total, around 75 000 m2 of land will be sold.

Outlook
As already reported, Rieter expects demand for new systems to normalize further in the coming months. Due to the capacity utilization at spinning mills, the company anticipates that demand for consumables, wear & tear and spare parts will remain at a good level.

For the full year 2022, due to the high order backlog and the consolidation of the businesses acquired from Saurer, Rieter expects sales of around CHF 1 400 million (2021: CHF 969.2 million). The reduced sales forecast compared to early 2022 (March 2022: CHF 1 500 million) reflects the impact of global supply bottlenecks. The realization of sales revenue from the order backlog continues to be associated with risks in relation to the well-known challenges.

Despite significantly higher sales, Rieter expects EBIT and net result for 2022 to be below the previous year’s level. This is due to the considerable increases in the cost of materials and logistics, additional costs for compensation of material shortages as well expenses in connection with the acquisition in the years 2021/2022. Despite the price increases already implemented, global cost increases continue to pose a risk to the growth of profitability.

Source:

Rieter Holding AG

(c) FET
FET meltspinning system for biomedical applications
15.09.2021

FET: Further Gains in the Biomedical sector

Fibre Extrusion Technology of Leeds, UK has delivered nine meltspinning systems to clients in the biomedical sector since the onset of the Covid-19 pandemic, with a similar number currently on order for 2021/22. This way FET could confirm the position as an acknowledged world leader in meltspinning equipment for the production of precursor materials used in medical devices and as a default supplier for absorbable suture production systems, with orders virtually doubling year on year.

Recent installations include a multi-functional system that can produce both multifilament and monofilament pre-cursor fibres, but nonwoven systems have been particularly prominent, driven by the burgeoning demand for FFP3 masks, gowns and other medical products required during the pandemic. These have been sold to medical device manufacturing companies across the globe, including the Far East, USA and Europe. Research organisations have also invested in FET systems for biomedical applications, the most recent being the University of Leeds in a laboratory scale Spunbond system.

Fibre Extrusion Technology of Leeds, UK has delivered nine meltspinning systems to clients in the biomedical sector since the onset of the Covid-19 pandemic, with a similar number currently on order for 2021/22. This way FET could confirm the position as an acknowledged world leader in meltspinning equipment for the production of precursor materials used in medical devices and as a default supplier for absorbable suture production systems, with orders virtually doubling year on year.

Recent installations include a multi-functional system that can produce both multifilament and monofilament pre-cursor fibres, but nonwoven systems have been particularly prominent, driven by the burgeoning demand for FFP3 masks, gowns and other medical products required during the pandemic. These have been sold to medical device manufacturing companies across the globe, including the Far East, USA and Europe. Research organisations have also invested in FET systems for biomedical applications, the most recent being the University of Leeds in a laboratory scale Spunbond system.

The FET in-house Process Development Laboratory and ongoing collaboration with biomaterial polymer suppliers has helped to optimise the biomedical melt spinning technology. The Laboratory is at the disposal of customers for all aspects of confidential testing and evaluation. To further increase this competitive edge, FET will be opening a new Process Development Laboratory and Visitor Centre in early 2022.

More information:
meltspinning FET
Source:

Projectmarketing for FET

15.07.2021

Rieter: First half of 2021

  • Order intake of CHF 975.3 million (first half of 2020: CHF 250.7 million).
  • Sales of CHF 400.5 million (first half of 2020: CHF 254.9 million).
  • EBIT of CHF 9.0 million and net profit of CHF 5.3 million

The first half of 2021 has been characterized by a strong market recovery in combination with a regional shift in demand for new machinery and systems. Rieter anticipates a normalization of the demand for new systems in the coming months. The company assumes that spinning mills will continue to work at high-capacity levels.

For the full year, Rieter expects sales to be above CHF 900 million.

The realization of sales from the order backlog continues to be associated with risks in light of bottlenecks in material deliveries and freight capacities as well as the ongoing pandemic in key markets for Rieter.

In recent years, Rieter has implemented its strategy based on the cornerstones of innovation leadership, strengthening the components, spare parts and services businesses, and adjusting cost structures.

  • Order intake of CHF 975.3 million (first half of 2020: CHF 250.7 million).
  • Sales of CHF 400.5 million (first half of 2020: CHF 254.9 million).
  • EBIT of CHF 9.0 million and net profit of CHF 5.3 million

The first half of 2021 has been characterized by a strong market recovery in combination with a regional shift in demand for new machinery and systems. Rieter anticipates a normalization of the demand for new systems in the coming months. The company assumes that spinning mills will continue to work at high-capacity levels.

For the full year, Rieter expects sales to be above CHF 900 million.

The realization of sales from the order backlog continues to be associated with risks in light of bottlenecks in material deliveries and freight capacities as well as the ongoing pandemic in key markets for Rieter.

In recent years, Rieter has implemented its strategy based on the cornerstones of innovation leadership, strengthening the components, spare parts and services businesses, and adjusting cost structures.

Crisis management in the pandemic year of 2020 was aimed at protecting employees, fulfilling customer commitments, ensuring liquidity, and also strengthening the market position for the time after the pandemic as well as retaining the ability to benefit from the incipient market recovery.

The focus for 2021 remains on the implementation of this strategy. The measures for crisis management relating to the protection of employees and fulfilling customer commitments are still in effect in countries that continue to be affected by the pandemic.

The Rieter Board of Directors has approved the implementation of the CAMPUS project. The Rieter CAMPUS comprises a customer and technology center as well as an administration building at the Winterthur location. It will make an important contribution to the implementation of the innovation strategy and to the enhancement of Rieter’s technology leadership position.

Source:

Rieter

07.04.2021

NCTO: Importance of the U.S. Textile Industry to Lifesaving PPE & the Economy

National Council of Textiles Organization (NCTO) member Parkdale Mills hosted Senator Tim Kaine (D-VA) at the company’s Magnolia Manufacturing plant in Hillsville, Va. today to showcase the critical role the company and the industry has played in producing lifesaving personal protective equipment (PPE) to aid frontline health-care workers and the country during the pandemic.

Parkdale’s facility in Hillsville, Va. is a key yarn spinning hub contributing to a major face mask initiative bringing together several U.S. companies and more than 5,000 workers as part of the Biden administration’s pledge to provide 25 million reusable face masks to communities hit hard by the pandemic.

National Council of Textiles Organization (NCTO) member Parkdale Mills hosted Senator Tim Kaine (D-VA) at the company’s Magnolia Manufacturing plant in Hillsville, Va. today to showcase the critical role the company and the industry has played in producing lifesaving personal protective equipment (PPE) to aid frontline health-care workers and the country during the pandemic.

Parkdale’s facility in Hillsville, Va. is a key yarn spinning hub contributing to a major face mask initiative bringing together several U.S. companies and more than 5,000 workers as part of the Biden administration’s pledge to provide 25 million reusable face masks to communities hit hard by the pandemic.

“Parkdale Mills thanks Senator Kaine for his leadership on policies that help bolster our company and the entire textile industry. We are proud to be part of an initiative that is bringing together American companies to produce 100% American-made masks for community health centers, soup kitchens and food banks across the country,” said Davis Warlick of Parkdale Mills. “With the support of our government and leaders like Senator Kaine, our industry is demonstrating its ability and capacity to make critical items here for the long term.”

Kim Glas, President and CEO of NCTO said: “We want to sincerely thank Senator Kaine for his leadership in supporting American manufacturers, which have played a vital role in our economy as well as the nationwide effort to produce critical PPE and medical textiles for a nation in crisis. We are grateful to the senator and the Biden administration for prioritizing domestic manufacturers and the U.S. workforce. The U.S. textile industry is a vital contributor to the U.S economy and policies that Senator Kaine supports help bolster the onshoring of PPE and critical items, which in turn spurs employment and investment in the American manufacturing base.”

09.03.2021

Rieter Financial Year 2020

Financial Year 2020

As a consequence of the COVID-19 pandemic, Rieter closed the 2020 financial year with sales of CHF 573.0 million, which corresponds to a decrease of 25% compared to the previous year (2019: CHF 760.0 million). Due to the low sales volume, a loss of CHF 84.4 million was recorded at the EBIT level while at the net profit level the loss was CHF 89.8 million. In view of the loss in the 2020 financial year, the Board of Directors proposes that shareholders waive the payment of a dividend for 2020.

Order intake of CHF 640.2 million in the 2020 financial year was 31% down on the previous year (2019: CHF 926.1 million). Following the significant slump in demand in the second quarter of 2020 (CHF 45.7 million), order intake recovered in the third quarter (CHF 174.4 million) and improved further in the fourth quarter (CHF 215.1 million).

At the end of 2020, the company had an order backlog of about CHF 560 million (December 31, 2019: about CHF 500 million).

Financial Year 2020

As a consequence of the COVID-19 pandemic, Rieter closed the 2020 financial year with sales of CHF 573.0 million, which corresponds to a decrease of 25% compared to the previous year (2019: CHF 760.0 million). Due to the low sales volume, a loss of CHF 84.4 million was recorded at the EBIT level while at the net profit level the loss was CHF 89.8 million. In view of the loss in the 2020 financial year, the Board of Directors proposes that shareholders waive the payment of a dividend for 2020.

Order intake of CHF 640.2 million in the 2020 financial year was 31% down on the previous year (2019: CHF 926.1 million). Following the significant slump in demand in the second quarter of 2020 (CHF 45.7 million), order intake recovered in the third quarter (CHF 174.4 million) and improved further in the fourth quarter (CHF 215.1 million).

At the end of 2020, the company had an order backlog of about CHF 560 million (December 31, 2019: about CHF 500 million).

Business Groups
Sales of the Business Group Machines & Systems amounted to CHF 295.8 million in 2020, which corresponds to a decrease of 24% compared to the previous year. Due to the low volume and taking into account the expenditure on the ongoing innovation program, the business group recorded a loss of CHF 72.4 million at the EBIT level. Order intake in the reporting year was CHF 363.9 million (-35% compared to the previous year).

The Business Group Components with sales of CHF 174.3 million (-24% compared to the previous year) achieved a profit of CHF 1.4 million at the EBIT level before restructuring charges. EBIT after restructuring charges was CHF -5.5 million. The order intake with CHF 169.1 million (-24% compared to the previous year) was just below sales.

The Business Group After Sales achieved sales of CHF 102.9 million (-27% compared to the previous year) and a positive EBIT of CHF 1.8 million. Order intake was CHF 107.2 million (-24% compared to the previous year). Over 60% of spinning mills were shut down in the second quarter of 2020, with a corresponding impact on the demand for spare parts.

Dividend
Due to the loss of CHF 89.8 million at the net profit level in the 2020 financial year, the Board of Directors proposes that shareholders waive the distribution of a dividend.

Outlook
Rieter expects the market recovery that began in the second half of 2020 to continue in 2021. The company expects an order intake in the first half of 2021 exceeding that of the previous half year (second half of 2020: CHF 389.5 million). Thanks to the improved capacity utilization, Rieter is planning short-time working in only a few areas in the first half of 2021. Nonetheless, as already announced, Rieter still anticipates that sales in the first half of 2021 will be below the break-even point. In connection with the high order backlog at the beginning of 2021, Rieter expects an operating profit for the full year 2021.

Source:

Rieter Management AG

27.01.2021

Rieter: First Information on the Financial Year 2020

Order Intake Continued to Recover in the Fourth Quarter of 2020:

  • Order intake increased to CHF 215.1 million in the fourth quarter of 2020 and reached a total of CHF 640.2 million in the 2020 financial year
  • As expected, sales of CHF 573.0 million in the 2020 financial year were significantly down on the previous year
  • EBIT margin of around -15% and net profit of around -16% of sales expected
  • First half of 2021 still heavily impacted by the COVID-19 pandemic
  • Change to the Group Executive Committee

Rieter posted a globally and broadly supported order intake of CHF 215.1 million in the fourth quarter of 2020. Thus, the recovery that began in the third quarter of 2020 after the slump in demand in the second quarter continued (order intake second quarter: CHF 45.7 million, third quarter: CHF 174.4 million). Overall, Rieter’s annual order intake for the 2020 financial year totaled CHF 640.2 million, which corresponds to a decrease of 31% compared to the previous year.

Order Intake Continued to Recover in the Fourth Quarter of 2020:

  • Order intake increased to CHF 215.1 million in the fourth quarter of 2020 and reached a total of CHF 640.2 million in the 2020 financial year
  • As expected, sales of CHF 573.0 million in the 2020 financial year were significantly down on the previous year
  • EBIT margin of around -15% and net profit of around -16% of sales expected
  • First half of 2021 still heavily impacted by the COVID-19 pandemic
  • Change to the Group Executive Committee

Rieter posted a globally and broadly supported order intake of CHF 215.1 million in the fourth quarter of 2020. Thus, the recovery that began in the third quarter of 2020 after the slump in demand in the second quarter continued (order intake second quarter: CHF 45.7 million, third quarter: CHF 174.4 million). Overall, Rieter’s annual order intake for the 2020 financial year totaled CHF 640.2 million, which corresponds to a decrease of 31% compared to the previous year.

At the end of 2020, the company had an order backlog of about CHF 560 million (December 31, 2019: about CHF 500 million).

As expected, as a consequence of the economic effects of the COVID-19 pandemic, the Rieter Group closed the 2020 financial year with considerably lower sales than in the previous year. According to the first, as yet unaudited figures, total sales of CHF 573.0 million were achieved, which corresponds to a decrease of 25% compared to the previous year (2019: CHF 760.0 million).

Order Intake by Business Group
All three business groups were affected by the slump in demand in the second quarter of 2020 due to the COVID-19 pandemic. Despite the recovery in order intake in the third and fourth quarters of 2020, the weak second quarter was only partially offset.

The Business Group Machines & Systems was particularly hard hit by the effects of the pandemic, with a year-on-year decline of 35%. The Business Groups Components and After Sales each recorded a 24% reduction in order intake.*

Sales by Business Group
The exceptional market situation in 2020 gave rise to a significant decline in sales in all three business groups. Accordingly, reluctance to invest and deferred deliveries by customers caused sales in the Business Group Machines & Systems to decline by 24% compared to the previous year.

Due to COVID-19, a large number of spinning mills stopped production worldwide. This led to low demand for spare parts and wear parts, especially in the second and third quarters of 2020. Accordingly, compared to the previous year, sales in the Business Groups Components and After Sales fell by 24% and 27% respectively in the 2020 financial year.*

Sales by Region
With the exception of Turkey, all regions were affected by the low demand as a consequence of the COVID-19 pandemic.*

EBIT Margin and Net Profit
In the 2020 financial year, Rieter anticipates an EBIT margin of around -15% (2019: 11.2%) and net profit of around -16% of sales (2019: 6.9%). As of December 31, 2020, Rieter had liquid funds of exceeding CHF 280 million and unused credit lines in the mid three-digit million range.

First Half of 2021 Still Heavily Impacted by the COVID-19 Pandemic
Thanks to the improved capacity utilization, Rieter is planning short-time working in only a few areas in the first half of 2021. Nevertheless, Rieter expects sales in the first half of 2021 to be below the break-even point.*

Change to the Group Executive Committee
With effect from March 1, 2021, the Board of Directors of Rieter Holding Ltd. has appointed Roger Albrecht as Head of the Business Group Machines & Systems and a member of the Group Executive Committee.*

Annual General Meeting April 15, 2021
The 2021 Annual General Meeting of Rieter Holding Ltd. will take place in Winterthur on April 15, 2021.*


*See attached document for more information.

Source:

Rieter Management AG

Rieter Investor Update 2020 (c) Rieter Management AG
Rieter Investor Update 2020
23.10.2020

Rieter Investor Update 2020

  • Significant recovery in order intake in third quarter 2020
  • Order intake of CHF 425.1 million after nine months
  • COVID crisis management in place
  • Continuous implementation of the strategy
  • Outlook 2020

The market recovery, which Rieter reported in June 2020, has continued. This is reflected in capacity utilization at spinning mills worldwide, which Rieter monitors. In April 2020, the proportion of producing spinning mills was around 40% while at the end of September 2020 this was around 90%. Against this backdrop, the Rieter Group increased order intake in the third quarter of 2020 to CHF 174.4 million (2nd quarter 2020: CHF 45.7 million). In the first nine months of 2020, the Rieter Group achieved a cumulative order intake of CHF 425.1 million (2019: CHF 524.5 million). Compared to the previous year period, this represents a decline of 19%.

Order Intake by Business Group

  • Significant recovery in order intake in third quarter 2020
  • Order intake of CHF 425.1 million after nine months
  • COVID crisis management in place
  • Continuous implementation of the strategy
  • Outlook 2020

The market recovery, which Rieter reported in June 2020, has continued. This is reflected in capacity utilization at spinning mills worldwide, which Rieter monitors. In April 2020, the proportion of producing spinning mills was around 40% while at the end of September 2020 this was around 90%. Against this backdrop, the Rieter Group increased order intake in the third quarter of 2020 to CHF 174.4 million (2nd quarter 2020: CHF 45.7 million). In the first nine months of 2020, the Rieter Group achieved a cumulative order intake of CHF 425.1 million (2019: CHF 524.5 million). Compared to the previous year period, this represents a decline of 19%.

Order Intake by Business Group

Due to the positive development in the third quarter of 2020, order intake at the Business Group Machines & Systems reached a total of CHF 234.5 million in the first nine months. The reason for the relatively small decline of 8% compared to the previous year is that the new machinery business was already characterized by investment restraint in the first three quarters of the year 2019. The Business Group Components recorded a reduction of 33% to CHF 116.6 million while the Business Group After Sales posted an order intake of CHF 74.0 million, a decrease of 23%. This illustrates the effects of low capacity utilization at the spinning mills, especially in the second quarter of 2020 as a result of the COVID-19 pandemic. The order backlog as of September 30, 2020, was around CHF 515 million (September 30, 2019: CHF 285 million). Cancellations were in the normal range of around 5%.

COVID Crisis Management in Place

Rieter has quickly implemented comprehensive COVID crisis management. Priority is being given to protecting employees, fulfilling customer commitments and ensuring liquidity. The necessary measures to protect employees have been implemented worldwide and the order backlog is being processed largely as planned. Rieter has introduced 40% short-time working in Switzerland and Germany for the second half of 2020. Similar measures were implemented worldwide within the scope of the available legal options. As of September 30, 2020, Rieter had liquid funds of CHF 216.7 million and unused credit lines in the mid three-digit million range in order to ensure liquidity. At the end of September 2020, net debt of CHF 1.2 million was disclosed.

Continuous Implementation of the Strategy

In recent years, Rieter has consistently implemented the strategy with the focus on innovation leadership, strengthening the business on the installed base and optimization of the costs. The company intends to forge ahead with the strategy in the coming months in order to strengthen the market position for the time after the COVID-19 pandemic. The Rieter CAMPUS is an important element of Rieter’s innovation strategy. Depending on the business situation, construction work is due to begin in the first half of 2021.

Outlook 2020

As already announced, in terms of sales and profitability Rieter expects a stronger second half of the year compared to the first half of 2020. Nevertheless, due to the deferral of deliveries by customers, Rieter will also conclude the second half of the year − and thus the full year 2020 − with a net loss. Due to the existing uncertainties, it continues to be difficult to forecast sales and profitability for the second half of 2020. For this reason, Rieter refrains from providing more specific information for the full year 2020.

More information:
Rieter Holding Ltd. Covid-19
Source:

Rieter Management AG

28.05.2020

Rieter: Business Situation facing COVID-19 Pandemic

  • Since the end of March 2020, COVID-19 has led to very low demand in all Business Groups
  • Comprehensive crisis management implemented
  • Loss in the mid double-digit million range expected in the first half of 2020
  • Plans to introduce short-time working to adjust capacity in Switzerland and Germany
  • Strategy will continue to be implemented

Due to COVID-19, a large number of spinning mills have stopped production worldwide. Since the end of March 2020, this has led to low demand for spare parts and wear & tear parts and delays in testing programs during the development of new machines. Customers are postponing investment projects or unable to implement them due to restrictions imposed by national governments. This results in low demand for new machines.

  • Since the end of March 2020, COVID-19 has led to very low demand in all Business Groups
  • Comprehensive crisis management implemented
  • Loss in the mid double-digit million range expected in the first half of 2020
  • Plans to introduce short-time working to adjust capacity in Switzerland and Germany
  • Strategy will continue to be implemented

Due to COVID-19, a large number of spinning mills have stopped production worldwide. Since the end of March 2020, this has led to low demand for spare parts and wear & tear parts and delays in testing programs during the development of new machines. Customers are postponing investment projects or unable to implement them due to restrictions imposed by national governments. This results in low demand for new machines.

Comprehensive crisis management
Rieter has implemented comprehensive crisis management. Priorities are being given to protecting employees, fulfilling customer commitments and ensuring liquidity. The necessary measures to protect employees have been implemented worldwide.
The order backlog of well in excess of CHF 500 million is being processed largely according to plan, despite the existing bottlenecks in the supply chains. Less than 5% of the orders in the order backlog have been canceled.
Rieter has already implemented measures to ensure liquidity and reduce costs. The company has good net liquidity and undrawn credit lines in the mid three-digit million range.
Loss expected in the first half of 2020
As already reported, Rieter expects sales and earnings in the first half of 2020 to be significantly below the prior year level.

Loss expected in the first half of 2020
As already reported, Rieter expects sales and earnings in the first half of 2020 to be significantly below the prior year level. The effects of COVID-19 will place an additional burden on the first half of 2020. Rieter therefore expects sales in the first half of 2020 to be less than CHF 300 million. Despite the countermeasures implemented at the net profit level, this will lead to a loss in the mid double-digit million range.

Plans to introduce short-time working to adjust capacity
Rieter plans to apply for short-time working for the areas with forecasted low capacity utilization at the locations in Switzerland and Germany. The application will be for 40% short-time working in the third quarter of 2020. Talks with staff representatives will begin next week.
As a sign of solidarity, Rieter’s Board of Directors, Group Executive Committee and the senior management will waive 10%-20% of their salaries temporarily.

Implementation of the strategy
In recent years, Rieter has consistently implemented the strategy based on innovation leadership, strengthening the business in components, spare parts and services and the adjustment of cost structures. The company intends to forge ahead with the implementation of the strategy in the coming months, thus strengthening its market position for the time after the COVID-19 pandemic.
The next information on the course of business is planned with the publication of the half-year results on July 16, 2020
 

More information:
Coronavirus Rieter
Source:

Rieter Holding AG

Logo oerlikon
Oerlikon blickt positiv in die Zukunft
23.04.2020

Oerlikon Manmade Fibers segment looking positively towards the future during the coronavirus pandemic

Staggered in terms of timing and with varying magnitude, the global spread of coronavirus is impacting the development of the regional economies in the core markets of the Manmade Fibers segment of the Swiss Oerlikon Group.
The sales markets for manmade fiber systems and equipment have been primarily located in China, India and Turkey for many years now. Together, these markets – above all China – make up the lion’s share of the project landscape at Oerlikon Manmade Fibers. And this is paying positive dividends at the moment. Because the production facilities of the major manmade fiber manufacturers in
China have been systematically fired up again over the past few weeks, with capacity utilization increasing consistently.

Staggered in terms of timing and with varying magnitude, the global spread of coronavirus is impacting the development of the regional economies in the core markets of the Manmade Fibers segment of the Swiss Oerlikon Group.
The sales markets for manmade fiber systems and equipment have been primarily located in China, India and Turkey for many years now. Together, these markets – above all China – make up the lion’s share of the project landscape at Oerlikon Manmade Fibers. And this is paying positive dividends at the moment. Because the production facilities of the major manmade fiber manufacturers in
China have been systematically fired up again over the past few weeks, with capacity utilization increasing consistently.

Going against the flow
The Segment CEO, Georg Stausberg explains the reason: “Long before the coronavirus situation developed, the major manmade fiber manufacturers in China had decided to reverse-integrate their production chains to include petrochemicals in order to expand their portfolios with targeted investments, to reduce their dependence on a ,single product’, to optimize their costs and ultimately to acquire greater control over margins in a global volume business”.
Similar processes and decisions – albeit not on the same scale as in China – have also
been detected at the large manmade fiber manufacturers in India and Turkey. Even though businesses in India and Turkey are presently still temporarily severely impacted by the coronavirus situation, their long-term commitment cannot however be questioned, as the company-internally-agreed plans will be systematically implemented moving forward.

Long-term investments of global market players
All this has recently resulted in increased demand for spinning and texturing systems – just like those supplied by total solutions provider Oerlikon Manmade Fibers with its
Oerlikon Barmag, Oerlikon Neumag and Oerlikon Nonwoven product brands.
“The investments in petrochemical systems are based on long-term strategic considerations and are resulting – even during the coronavirus pandemic – neither in short- and medium-term economic dips, nor in changed customer behavior. (...)”, states Segment-CEO Georg Stausberg.
As a result of Oerlikon Manmade Fibers delving into the digital age years ago, the segment has experienced the intensive and short-term benefit from all the measures, in part also in its processing of customer projects.

Source:

Marketing, Corporate Communications
& Public Affairs