From the Sector

Reset
12 results
06.11.2023

Mahlo presents new solutions at ITMA Asia 2023

Mahlo GmbH + Co. KG will present its systems and solutions for efficient and high-quality textile production and finishing together with Shanghai Kuantex at ITMA Asia (November 19 and 23). The focus will be on the machine manufacturer's new straightening concept, the Orthopac RXVMC.

"In the new straightening concept, special attention was paid to the straightening mechanics and their interaction with the analysis electronics of the probe system," explains Sales Manager Thomas Höpfl. The control concept is also new. A probe group at the leveler infeed detects distortions even before they reach the correction rolls. In this way, the rolls are brought directly into position and the fabric is corrected from the very first centimeter. A scanner group at the outfeed also detects possible residual distortion, which is corrected at the second straightening module. This enables an even more precise and faster response when it comes to reacting to rapidly changing distortions. The Orthopac RXVMC therefore shows its full strength when straightening knitwear and fabrics sensitive to distortion.

Mahlo GmbH + Co. KG will present its systems and solutions for efficient and high-quality textile production and finishing together with Shanghai Kuantex at ITMA Asia (November 19 and 23). The focus will be on the machine manufacturer's new straightening concept, the Orthopac RXVMC.

"In the new straightening concept, special attention was paid to the straightening mechanics and their interaction with the analysis electronics of the probe system," explains Sales Manager Thomas Höpfl. The control concept is also new. A probe group at the leveler infeed detects distortions even before they reach the correction rolls. In this way, the rolls are brought directly into position and the fabric is corrected from the very first centimeter. A scanner group at the outfeed also detects possible residual distortion, which is corrected at the second straightening module. This enables an even more precise and faster response when it comes to reacting to rapidly changing distortions. The Orthopac RXVMC therefore shows its full strength when straightening knitwear and fabrics sensitive to distortion.

Also contributing to high-quality textile production and finishing is the Famacont PMC for controlling weft and stitch course density, which will also be on show at ITMA Asia. The Famacont PMC-15 uses a sensor to measure the yarn or stitch density and compares it with the target value stored in the recipe data management system. The detected deviation of the yarn density from the target value is used to fully automatically regulate the leading during the needling process on the stenter frame. Interested parties can have the mode of operation explained to them at the Mahlo booth with the help of a demo tower and their own or provided fabric samples.

Another major topic remains Industry 4.0, because the best measured data is of no use if it cannot be utilized. Mahlo has continuously developed its digital environment mSmart. "Our systems generate data that the customer can use immediately to regulate goods on-line. At the same time, all measured values are backed up in our data management system mLog enhanced and can be retrieved at any time. With this historical data, processes can be optimized and weak points in the process can be minimized," explains Sales Manager Thomas Höpfl.

20.09.2023

TMAS Members at ITMA Asia + CITME 2023

Members of TMAS – the Swedish Textile Machinery Association – will be taking part in the forthcoming ITMA Asia + CITME exhibition, taking place from November 19-23 2023 at the National Exhibition and Convention Centre in Shanghai, China.

Weaving
In the area of weaving, 93% of the 114,000 new looms delivered in 2022 went to Asia, according to the latest figures from the International Textile Manufacturers Federation (ITMF), with China the top destination, followed by India.
As a result, TMAS members like Vandewiele Sweden AB and Eltex have a huge market to address that has been established over many decades.

Vandewiele Sweden AB benefits from all of the synergies and accumulated know-how of the market-leading Vandewiele Group, supplying weft yarn feeding and tension control units for weaving looms to the majority of weaving machine manufacturers. It also retrofits its latest technologies to working mills to enable instant benefits in terms of productivity and control.

Members of TMAS – the Swedish Textile Machinery Association – will be taking part in the forthcoming ITMA Asia + CITME exhibition, taking place from November 19-23 2023 at the National Exhibition and Convention Centre in Shanghai, China.

Weaving
In the area of weaving, 93% of the 114,000 new looms delivered in 2022 went to Asia, according to the latest figures from the International Textile Manufacturers Federation (ITMF), with China the top destination, followed by India.
As a result, TMAS members like Vandewiele Sweden AB and Eltex have a huge market to address that has been established over many decades.

Vandewiele Sweden AB benefits from all of the synergies and accumulated know-how of the market-leading Vandewiele Group, supplying weft yarn feeding and tension control units for weaving looms to the majority of weaving machine manufacturers. It also retrofits its latest technologies to working mills to enable instant benefits in terms of productivity and control.

Yarn and sewing thread monitoring
With nearly 70 years of expertise in yarn sensor technology, Eltex of Sweden AB has been at the forefront of new product development. Its EYE and EyETM systems are capable of accurately and efficiently monitoring the movement and tension of more than 1,000 yarns simultaneously. These systems are suitable for various applications and fibre types, including warping, winding, multiaxial weaving and new material applications.

Eltex sewing tension monitors, such as the ETM422, have been well-received by customers. This device can monitor the tension of sewing threads in real time, effectively improving the quality and safety of sewn products. Particularly in China's rapidly growing automotive manufacturing sector, the ETM422 has seen widespread use to meet the industry’s escalating demands for product safety and quality.

Dyeing and finishing
“Digitalisation, automation and AI have become the key enablers for sustainable gains across the entire textile industry and so much has been achieved in the past few years, especially in terms of automation,” says TMAS secretary general Therese Premler-Andersson. “One area in which TMAS members are really making a difference right now, is in replacing water and energy-intensive technologies for the dyeing and finishing processes with new digital technologies.”

The TexCoat G4 non-contact spray technology for textile finishing and remoistening, for example, will be showcased in Shanghai by Baldwin. It not only reduces water, chemicals and energy consumption, but also provides the flexibility to adapt to a customer’s requirements in terms of single and double-sided finishing applications. The TexCoat G4 can reduce water consumption by as much as 50% compared to traditional padding application processes.

18.11.2022

Monforts at Igatex 2022

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts customers in the regions around the country’s three biggest cities of Karachi, Lahore and Faisalbad include all of the main players in the fields of home textiles and denim production, including Afroze, , Al Karam Artistic Milliners, Azgard-9, Crestex, , Gul Ahmed, Interloop, Liberty Mills, Lucky Textile Mills, Mustaqim, Naveena (NDL), Rajby Industries, Sapphire Finishing, Soorty, Style Textile and US Denim.

These companies rely on established Monforts technologies including Montex stentering equipment, Monfortex sanforizing units and Thermex dyeing ranges. The company’s Matex Eco Applicator minimum application system has also proved a big hit in recent years.

Monforts has also achieved considerable success in Pakistan with its Econtrol®* dyeing system  – an effective and established dyeing process. More than 40 Thermex continuous dyeing ranges have been installed in Pakistan in recent years and operator training on the Econtrol®* process by sophisticated technologists is an additional service.

The Econtrol® pad-dry process has a number of immediate benefits. Compared to the common pad-dry-pad-steam process, no salt is used and no steamer is required for a separate fixation step. Compared to the pad-dry-thermofix process, no urea is used and no smoke or deposits are generated, and unlike with the cold pad batch process, direct feedback of the dyeing results ensures no batching time is necessary and guarantees good reproducibility from the lab to bulk production.

An immediate wash off is also unnecessary, allowing for flexible production planning. The process is suitable for pale to dark shades with very good fastness properties. Also waste water treatment is improved by this technology.

*Econtrol is a registered mark of Dystar Colours Distribution GmbH.

Source:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

Photo: Sellers Textile Engineers
Hybrid Shearing Cylinder
10.10.2022

The Hybrid Shear by Sellers Textile Engineers

BTMA member Sellers Textile Engineers is marking its 110th anniversary this year with the introduction of a new concept in carpet shearing, as the essential final step in ensuring tuft uniformity and ‘just new’ freshness in finished carpet rolls.

The company has for many years offered two options in the construction of its shearing cylinders – the first, namely the ‘strap-on’, incorporates spiral blades bolted to the cylinder body and the second, known as the ‘caulked-in’, includes spirals which are fixed very securely in a machined groove within the machine.

The new Sellers’ Hybrid Shearing Cylinder combines the benefits of both, resulting in an improved cut and finer finish, in addition to longer repeatable finishing and increased rigidity.

BTMA member Sellers Textile Engineers is marking its 110th anniversary this year with the introduction of a new concept in carpet shearing, as the essential final step in ensuring tuft uniformity and ‘just new’ freshness in finished carpet rolls.

The company has for many years offered two options in the construction of its shearing cylinders – the first, namely the ‘strap-on’, incorporates spiral blades bolted to the cylinder body and the second, known as the ‘caulked-in’, includes spirals which are fixed very securely in a machined groove within the machine.

The new Sellers’ Hybrid Shearing Cylinder combines the benefits of both, resulting in an improved cut and finer finish, in addition to longer repeatable finishing and increased rigidity.

“The Hybrid Shearing Cylinder has all the advantages of the ‘strap-on’ spiral blade to provide a sharper and cleaner cut, along with enhanced rigidity which significantly lengthens the intervals between the necessary regrinding of the blade,” explains Sellers Director Neil Miller. “We currently have six Hybrid Shearing Cylinders operating in the field and the earliest, which has been installed in both No1 Head position, where the majority of the shearing operation and heaviest cut is performed, and also in No3 Head, where the sharper cutting angle has resulted in a much improved surface quality.”

Sellers shearing machines have led the field in carpet finishing for many decades, enabling the leading manufacturers to stay competitive by enabling the highest quality of finish to be achieved economically and efficiently.

The latest advanced features of these machines include a load cell tension control drive system, an automated touchscreen for easy operator control and fault diagnosis, an enhanced cleaning system including cylinder and blade separation and fully controllable pivoting beds. Further options include thickness monitoring, seam detection and metal detection systems.

“The Hybrid Shearing Cylinder will become standard on our latest machines and also be made available for retrofitting, to provide significant benefits to our existing users,” says Miller. “All of our equipment is designed, manufactured, assembled and tested at our plant in the UK, and as one of the few remaining European engineering companies to make all of our components in-house – with now over a century of accumulated know-how – flexibility in design allows our finishing solutions to be targeted to specific customers and their product requirements. Aligned to this is a lead in process control systems which ensure the accurate control, reliability and repeatability of the processing parameters on all of our machines.”

Sellers remains committed to providing complete finishing solutions for all carpet, tile and artificial grass products. Its range includes machines for tufted secondary backing, both conventional, powder and extrusion lamination, Wilton and Axminster products, artificial grass and foam lines, coating lines for bitumen, PVC, PU and other polymers, as well as shearing for all carpet products.

Ongoing developments on the company’s coating and drying lines have resulted in improved guiding and product tension control as well as dryer efficiency, reducing heat loss and optimising energy use. These include a re-design of the fan pressure boxes and impingement nozzles to increase airflow efficiency, modulating gas burners and introducing easy clean, accessible filters.

In addition, the proven dual zone system has been enhanced, giving a temperature differential of up to 80°C between top and bottom zones. Dryers can be heated by either gas or steam and operation and access have been simplified with controls via touchscreen and PLC.

An extensive range of ancillary equipment is available to provide maximum flexibility to cover product requirements, for both new processing lines and as upgrades to existing equipment.

“Carpet manufacturing is now based on well-established, tried and trusted processes and it’s rare for new innovations to be introduced into this sector,” says Jason Kent, CEO of the British Textile Machinery Association. “The new Sellers Hybrid Shearing Cylinder can provide a competitive edge for manufacturers which is currently being proven in the field. It’s one of a number of new innovations the company is planning to showcase at next year’s ITMA exhibition in Milan.”

(c) Baldwin Technology Company Inc.
Baldwin’s Rick Stanford and Fi-Tech’s Ian Mills kick off partnership with a handshake
03.10.2022

Baldwin Technology partners with Fi-Tech to represent textile finishing technologies

Baldwin Technology Co. Inc. and Fi-Tech Inc. join partnership to ensure service amid growing demand for sustainable solutions. Fi-Tech Inc. will represent Baldwin Technology Co. Inc.’s complete textile and nonwoven product lines as its sales agent in the U.S. and Canada.

Founded in 1972 and headquartered in Richmond, Virginia, Fi-Tech is an agency and distribution firm for textile and non-woven machinery. Its initial focus was on synthetic fibers and nonwovens and it has since expanded its portfolio to represent manufacturers of complete machines or technical components used in the production of nonwovens, synthetic fibers, polymer, textiles, converting, perforated products and tobacco processing. Fi-Tech also maintains a spare parts inventory for many of the companies it represents.

Baldwin Technology Co. Inc. and Fi-Tech Inc. join partnership to ensure service amid growing demand for sustainable solutions. Fi-Tech Inc. will represent Baldwin Technology Co. Inc.’s complete textile and nonwoven product lines as its sales agent in the U.S. and Canada.

Founded in 1972 and headquartered in Richmond, Virginia, Fi-Tech is an agency and distribution firm for textile and non-woven machinery. Its initial focus was on synthetic fibers and nonwovens and it has since expanded its portfolio to represent manufacturers of complete machines or technical components used in the production of nonwovens, synthetic fibers, polymer, textiles, converting, perforated products and tobacco processing. Fi-Tech also maintains a spare parts inventory for many of the companies it represents.

“With the increasing demand of Baldwin’s finishing technology, we needed to find the right partner for sales promotion in the U.S. and Canadian markets for knits, wovens and non-wovens,” said Rick Stanford, Baldwin Technology’s VP Global Business Development, Textiles. “Fi-Tech of Richmond, Virginia is the perfect partner. They are well established in the textile and non-wovens industry and their portfolio of principals provides excellent synergy with Baldwin’s precision spray and plasma treater systems.”

Baldwin’s solutions are used in a wide variety of fabrics from basic jersey and fleece with softening and anti-microbial finishes to technical fabrics such as outdoor gear, military, upholstery, automotive and industrial fabrics utilizing the latest in technical finishes such as DWR, soil release, flame retardants and insect repellent among others.

Source:

Baldwin Technology Company Inc. / Adduco Communications

Photo: AWOL
20.09.2022

Halley Stevensons: Unique waxed cotton finishing with new Monforts line

Monforts has installed and commissioned a new Montex finishing range at the Baltic Works of Halley Stevensons in Dundee, Scotland, to further boost the weatherproofing specialist’s highly flexible operations.

The range, with a working width of two metres, was built at the Montex assembly plant in Austria and consists of a Montex®Coat coating unit in knife execution for paste and foam coating and a Montex 8500 6F stenter.

Founded in 1864, Halley Stevensons has amassed unique technical know-how and manufacturing experience in the art of waxed cotton for weatherproofed fabrics and is able to provide international orders in custom colours and finishes to very low minimum quantities where required. The company exports worldwide and its premium brand customers include Belstaff, Barbours, Filson and J.Crew.

The range has replaced one of the company’s older stenter/coating lines and has already enabled Halley Stevensons to recreate various products with lower coating applications at higher speeds than was previously possible.

Monforts has installed and commissioned a new Montex finishing range at the Baltic Works of Halley Stevensons in Dundee, Scotland, to further boost the weatherproofing specialist’s highly flexible operations.

The range, with a working width of two metres, was built at the Montex assembly plant in Austria and consists of a Montex®Coat coating unit in knife execution for paste and foam coating and a Montex 8500 6F stenter.

Founded in 1864, Halley Stevensons has amassed unique technical know-how and manufacturing experience in the art of waxed cotton for weatherproofed fabrics and is able to provide international orders in custom colours and finishes to very low minimum quantities where required. The company exports worldwide and its premium brand customers include Belstaff, Barbours, Filson and J.Crew.

The range has replaced one of the company’s older stenter/coating lines and has already enabled Halley Stevensons to recreate various products with lower coating applications at higher speeds than was previously possible.

Waxed cotton was originally developed by sailors in the early 15th century when Scottish North Sea herring fleets began treating flax sailcloth with fish oils and grease in an attempt to waterproof their sails. Remnants of these sails were used by the sailors as capes to withstand the high winds and sea spray.

By the mid 1850s, sailcloth was being treated with linseed oil, but while initially highly effective, it would yellow and stiffen through weathering over time and eventually lose its waterproofing qualities.

In the years that followed, various treatments were applied to cottons in an attempt to find the most effective weatherproofing solution, and the combination of densely-woven cotton impregnated with a paraffin waxed coating proved most successful. For over 150 years, Halley Stevensons created many different variations of both woven constructions and finishing treatments and now supplies thousands of metres of waxed cotton every year, with each roll produced to custom specifications.

“The beauty of waxed cotton is its durability and longevity,” says Managing Director James Campbell. “The fabrics are breathable, with the wax adjusting to ambient temperatures to be softer and more breathable in warm weather and stiffer and more wind proof in cold conditions.”
While traditional waxes are petroleum or paraffin based, Halley Stevensons has always been comfortable about using a waste product from industry and reusing it to make products that last a lifetime.  

“We are always exploring different finishing techniques and one of our most popular finishes is our hybrid aero – an emulsified blend of waxes,” Campbell says. “This fabric is water repellent but has little wax in the mixture so the handle is much drier to touch than the traditional wet waxes.”

The company has also recently launched a new 100% plant-based wax – Ever Wax Olive – consisting of a blend of olive oil, rape seed and castor bean with comparable water repellence to petroleum and a far better rating than other natural waxes which have come before it.

“The high tradition of skills and fabric innovation imposed by our original guildsmen is still our benchmark standard of honest workmanship today,” Managing Director James Campbell concludes “We use responsibly sourced cotton fabrics and processes that are gentle to the product and low impact to the environment. Our dyeing methods use very low levels of water and our waxes are simply heated up for application and cooled down to store when not in use, meaning no waste discharges. Now, with this new Monforts line, we are also achieving running speeds two-to-three times faster than with the older stenter, combined with less gas usage. It’s proved a great partnership.”

Baldwin’s non-contact spray technology Texcoat G4. (Photo: Baldwin)
15.06.2022

Archroma and Baldwin to collaborate for optimized performance and resource saving in textile finishing

Archroma, a global leader in specialty chemicals towards sustainable solutions, and Baldwin, a leading global manufacturer and supplier of precision spray systems and technology for sustainable textile manufacturing, announce a new collaboration to optimize performance and resource saving in the finishing department.

The two companies aim to support textile manufacturers in their development projects, targeting to improve their product safety, performance and functionality, while at the same time maximizing the productivity and resource utilization of the finishing application process.

Archroma and Baldwin are collaborating in multiple projects that combine Archroma’s most sustainable product innovations with Baldwin’s Texcoat G4.

TexCoat G4 is a non-contact spray technology for textile finishing and remoistening, designed to allow a controlled and optimal coverage of the exact amount of finish chemistry for reaching specific characteristics of the fabric. The system can be used to reduce water consumption by as much as 50% compared to traditional padding application processes.

Archroma, a global leader in specialty chemicals towards sustainable solutions, and Baldwin, a leading global manufacturer and supplier of precision spray systems and technology for sustainable textile manufacturing, announce a new collaboration to optimize performance and resource saving in the finishing department.

The two companies aim to support textile manufacturers in their development projects, targeting to improve their product safety, performance and functionality, while at the same time maximizing the productivity and resource utilization of the finishing application process.

Archroma and Baldwin are collaborating in multiple projects that combine Archroma’s most sustainable product innovations with Baldwin’s Texcoat G4.

TexCoat G4 is a non-contact spray technology for textile finishing and remoistening, designed to allow a controlled and optimal coverage of the exact amount of finish chemistry for reaching specific characteristics of the fabric. The system can be used to reduce water consumption by as much as 50% compared to traditional padding application processes.

Archroma and Baldwin are currently testing Archroma’s finishing products and systems, such as the soon-to-be-launched PFC-free* Smartrepel® Hydro SR for water-based soil repellence, as well as metal and inorganic particle-free antimicrobial technologies like Sanitized T 20-19 and TH 15-14, which will be launched at the upcoming Techtextil 2022.

The first test results will be available for discussions with both partners at Techtextil at their respective booths.

ECO-COAT minimum application unit (c) Brückner
Minimalauftragsaggregat ECO-COAT
02.06.2022

BRÜCKNER: Answering current challenges of the textile industry

The German machinery producer BRÜCKNER used exactly these chances and repositioned itself during the pandemic period. For more than 70 years, the family-run company has been specialized in individual finishing concepts for textiles, technical textiles, nonwovens and floor coverings. The current challenges in the textile industry are serious. The clear increase of the energy costs and the general uncertainty of the energy supply as well as political requirements make a profitable textile production more and more demanding for many companies.

The German machinery producer BRÜCKNER used exactly these chances and repositioned itself during the pandemic period. For more than 70 years, the family-run company has been specialized in individual finishing concepts for textiles, technical textiles, nonwovens and floor coverings. The current challenges in the textile industry are serious. The clear increase of the energy costs and the general uncertainty of the energy supply as well as political requirements make a profitable textile production more and more demanding for many companies.

The company responds to this with a newly developed stenter concept with double heating system. Depending on availability, the lines can be operated with gas or oil, but also other combinations with steam or renewable energies are possible. This means that production delays and machine downtimes can be avoided as far as possible. In addition, developed intelligent assistance systems for its machines have been developed that support the machine operator in using the best possible process to operate the line as energy-efficiently as possible. Further energy savings are possible with new energy-efficient motors or heat-recovery and exhaust air cleaning systems. This also helps to avoid harmful emissions.

But many textile producers are also focusing on reducing chemicals. For this purpose, BRÜCKNER's further developed ECO-COAT minimum application unit can make a decisive contribution. Knitted and woven fabrics, but also nonwovens can be finished on one or both sides via different fabric paths. With the minimum application via an engraved roller, a single-sided application of up to 100 g/m² can be achieved. A double-sided and higher application quantity is achieved, for example, by impregnation in the nip. Irrespective of the selected fabric path, a very small liquor reservoir means that only minimal quantities of waste water are produced when changing batches or liquors, and the use of chemicals can also be significantly reduced. In addition, less water has to be evaporated in the subsequent drying process than, for example, in the case of impregnation in a water bath, so the energy requirement is significantly reduced.

On the two upcoming trade fairs ITM in Istanbul and TECHTEXTIL in Frankfurt in June, interested customers can personally get an idea of BRÜCKNER's new developments.

Source:

Brückner Trockentechnik GmbH & Co. KG

31.03.2022

Monforts at Techtextil North America

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Monforts will highlight its advanced finishing and coating technologies for the production of technical textiles at Techtextil North America, which takes place at the Georgia World Congress Center in Atlanta from May 17-19.

The company and its US representative PSP Marketing, of Charlotte, North Carolina, will be part of the centrepiece VDMA German Pavilion at the show.

Energy prices
With energy prices continuing to go through the roof, an emphasis at Techtextil North America will be on the energy and heat recovery that can be achieved with Montex stenters, through features such as the MonforClean system, in which waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required. A range of further resource-saving and energy recovery options can be specified per individual line installation.

Advanced machine operation
With the highly intuitive Qualitex 800 visualization software, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

The Qualitex 800 system is available for the automatic and continuous operation of the company’s Montex stenters, as well as its Thermex continuous dyeing ranges, Monfortex shrinking systems and Montex®Coat coating units.

Versatility is the key
Monforts Montex®Coat coating units serve an equally diverse number of markets, including tents, tarpaulins and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments and solvent coatings (in explosion-proof conditions) with knife coating, roller coating or screen printing can all be accommodated with this system.

Source:

AWOl Media / A. Monforts Textilmaschinen GmbH & Co. KG

(c) Brückner Trockentechnik GmbH & Co. KG
BRÜCKNER ECO-HEAT and ECO-AIR system on the stenter at FEINJERSEY
19.08.2021

Sustainable production technology from BRÜCKNER

  • Long-term partnership between the Austrian textile producer FEINJERSEY and the German textile machinery manufacturer BRÜCKNER

The Feinjersey Group is an internationally operating textile company and supplies the "global players" of the textile industry worldwide. The value chain of the company, which is based in Götzis, Austria, ranges from yarn processing to the finished product.

As a fully integrated production company, the internationally active textile company Feinjersey attaches great importance to a high quality standard and guarantees care at every step in the process chain. With approx. 250 employees and annual sales of around 45 million euros, the company knits, dyes and finishes top-quality knitted fabrics as well as elastic woven fabrics for a wide range of applications.

Products are made for the fashion, sports, workwear and technical textiles sectors. Among other things, fabrics for the automotive industry, laminating backings and coating substrate for artificial leather or foils, construction textiles or fabrics for medical technology are all produced.

  • Long-term partnership between the Austrian textile producer FEINJERSEY and the German textile machinery manufacturer BRÜCKNER

The Feinjersey Group is an internationally operating textile company and supplies the "global players" of the textile industry worldwide. The value chain of the company, which is based in Götzis, Austria, ranges from yarn processing to the finished product.

As a fully integrated production company, the internationally active textile company Feinjersey attaches great importance to a high quality standard and guarantees care at every step in the process chain. With approx. 250 employees and annual sales of around 45 million euros, the company knits, dyes and finishes top-quality knitted fabrics as well as elastic woven fabrics for a wide range of applications.

Products are made for the fashion, sports, workwear and technical textiles sectors. Among other things, fabrics for the automotive industry, laminating backings and coating substrate for artificial leather or foils, construction textiles or fabrics for medical technology are all produced.

The Austrian textile manufacturer has been certified with the Bluesign textile seal and ensures efficient use of resources with modern machinery. Water and energy consumption as well as pollutant emissions are to be reduced to a minimum.

In textile finishing in particular, the focus is on minimising energy consumption as this process is the most energy-intensive in the entire process chain. Feinjersey uses its own photovoltaic system for this purpose, as well as the heat recovery and exhaust air purification systems on the stenter frames. By using the waste heat from production, the company's buildings are heated. All six stenter frames at Feinjersey are made by BRÜCKNER and produce with three-stage heat recovery and exhaust air purification systems.

The latest BRÜCKNER line has a working width of 4.20 m and is mainly used for the finishing of high-ly elastic and extremely sensitive knitted fabric. In order to avoid yellowing on the fabric, the stenter is equipped with an indirect gas heating system. The knitting oil vapours coming from the fabric during the heat-setting process are extracted from the dryer and cleaned in a BRÜCK-NER ECO-AIR exhaust air cleaning system before being extracted to atmosphere. The complete exhaust air treat-ment on the newest stenter is carried out by a multistage BRÜCKNER ECO-HEAT and ECO-AIR system.

Source:

Brückner Trockentechnik GmbH & Co. KG

(c) Brückner Trockentechnik GmbH & Co. KG
12.08.2021

BRÜCKNER successful in Turkey with stenters

The Turkish company ARIKAN Mensucat Industry and Trade Inc. was founded in 1993 and is located in Kahramanmaraş, one of the southernmost cities of the country. Today, the family-owned company employs around 1,500 people and finishes around 55 tons of knitwear every day. In addition to many well-known Turkish fashion manufacturers, ARIKAN also supplies international manufacturers in Europe, Russia, the Gulf States and other leading international markets.

The Turkish company ARIKAN Mensucat Industry and Trade Inc. was founded in 1993 and is located in Kahramanmaraş, one of the southernmost cities of the country. Today, the family-owned company employs around 1,500 people and finishes around 55 tons of knitwear every day. In addition to many well-known Turkish fashion manufacturers, ARIKAN also supplies international manufacturers in Europe, Russia, the Gulf States and other leading international markets.

The German machinery manufacturer BRÜCKNER supported the Turkish company from the very beginning. From the foundation of the dyeing and finishing plant, BRÜCKNER supplied three stenters for the finishing of the high-quality knitted fabric in 2014. Two more lines followed in 2016. For decades, BRÜCKNER has been the market leader for the finishing of knitted fabric. Especially for very fine and elastic fabric, special line configurations and technological know-how are necessary to be able to produce a high-quality end product. During the drying and heat-setting process, for example, extremely accurate and uniform temperature distribution over the entire length and width of the dryer is essential. In the BRÜCKNER stenter this is achieved, among other things, by the alternating arrangement of the thermal zones every 1.5 meters and by the proven split-flow air system.

The machine operators at ARIKAN appreciate the easy control of BRÜCKNER lines. The visualization is intuitively designed and offers many auxiliary systems for an optimized production process. In addition, significant energy savings can be achieved with just a few changes to the machine parameters.

The management at ARIKAN attaches great importance to energy saving, especially in the fabric finishing department. The drying process is one of the most energy-intensive in the entire process chain, therefore the biggest savings can be made here. These have a direct impact on the manufacturing costs of the textiles and thus on competitiveness in the market. In the meantime, talks are already in progress for another BRÜCKNER line which will include a very special feature: a combined heating system for the dryer. For many customers - and so also for ARIKAN in Turkey - e.g. steam energy is available free or very cheap. With the combined heating system developed by BRÜCKNER it is possible to use this steam energy for heating up the dryer and thus to achieve significant savings. If the available steam is not sufficient for a running process, it is automatically switched over to gas heating. This mode of operation does not only have an effect on the energy costs, but also makes a considerable contribution to environmental protection.

TexCoat G4 non-contact precision spray fabric-finishing system (c) Baldwin Technology Company Inc.
02.08.2021

Baldwin at Techtextil North America

  • Introducing TexCoat G4 to US textile industry
  • Non-contact precision spray fabric-finishing system enhances sustainability and process control

Baldwin Technology Company Inc. will be showcasing its TexCoat G4 non-contact precision spray fabric-finishing system at the Techtextil North America trade show, held Aug. 23 to 25, in Raleigh, North Carolina.

With extensive sustainability benefits, unprecedented tracking and process control, and Industry 4.0 integration, the TexCoat G4 provides consistently high-quality fabric finishing, with no chemistry waste, and significantly reduced water and energy consumption.

Baldwin’s innovative non-contact spray technology eliminates chemistry dilution in wet-on-wet processes. The TexCoat G4 consistently and uniformly sprays chemistry across the fabric surface and applies it only where needed, on one or both sides.

  • Introducing TexCoat G4 to US textile industry
  • Non-contact precision spray fabric-finishing system enhances sustainability and process control

Baldwin Technology Company Inc. will be showcasing its TexCoat G4 non-contact precision spray fabric-finishing system at the Techtextil North America trade show, held Aug. 23 to 25, in Raleigh, North Carolina.

With extensive sustainability benefits, unprecedented tracking and process control, and Industry 4.0 integration, the TexCoat G4 provides consistently high-quality fabric finishing, with no chemistry waste, and significantly reduced water and energy consumption.

Baldwin’s innovative non-contact spray technology eliminates chemistry dilution in wet-on-wet processes. The TexCoat G4 consistently and uniformly sprays chemistry across the fabric surface and applies it only where needed, on one or both sides.

Customers can expect no bath contamination during the finishing process, as well as minimal downtime during changeovers, which are made easy with recipe management that includes automated chemistry and coverage selection. The TexCoat G4 also enhances sustainability by wasting no chemistry during color, fabric or chemistry changeovers, and because only the required chemistry volume is applied to the fabric, wet pick-up levels can be reduced by up to 50 percent—leading to 50 percent less water and energy consumption.

Furthermore, in single-side applications, drying steps can be eliminated for various textiles, including those that are back-coated and laminated, thereby streamlining and simplifying the production process.

Source:

Baldwin Technology Company Inc.