From the Sector

Reset
67 results
60th anniversary of Eltex of Sweden AB (c) Eltex of Sweden
21.02.2024

60th anniversary of Eltex of Sweden AB

Eltex of Sweden, a pioneer in the adoption of electronic sensors by the weaving machinery industry, is marking its 60th anniversary this month.

The electronic detection of broken or missing weft yarns during production was the problem Eltex founders Åke Rydborn and Ragnar Henriksson set out to solve with the development of the world’s first electronic weft-stop-motion. Its potential was recognised on its introduction at the 1963 ITMA exhibition in Hannover, Germany, leading to the foundation of the company in a modest 12-square-metre workshop in Älmhult, Sweden, in February 1964.

Eltex of Sweden, a pioneer in the adoption of electronic sensors by the weaving machinery industry, is marking its 60th anniversary this month.

The electronic detection of broken or missing weft yarns during production was the problem Eltex founders Åke Rydborn and Ragnar Henriksson set out to solve with the development of the world’s first electronic weft-stop-motion. Its potential was recognised on its introduction at the 1963 ITMA exhibition in Hannover, Germany, leading to the foundation of the company in a modest 12-square-metre workshop in Älmhult, Sweden, in February 1964.

By 1968 the company was operating from a modern 3,000-square-metre plant and beginning to establish a global presence, introducing the first all-in-one printed circuit board (PCB) for its sensor systems in 1971. As exports increased, further Eltex operations were established in the USA and Ireland and the company expanded its product range including energy control devices, temperature and humidity loggers, food handling safety systems, and military grade battery chargers. Further textile milestones in parallel to advances in weaving technology included optical arrival detectors for air-jet weaving machines at the beginning of the 1980s, and the QTV system for warp preparation, which introduced digital stop-motion control to the industry at the start of the 1990s. In 2009, the company branched out into carpet tufting, first with the CoTS clamp-on tube sensor for tufting machines, followed by the Compact sensor for tufting machines in 2013. In 2019 the Compact II further cemented the company’s position in this sector.

Newly developed Eltex EyETM and ACT-R
Most recently, Eltex has launched the Eltex EyETM system for the monitoring of yarn tension on warp beams. Not only does it eliminate problems when warping, but also in the subsequent weaving or tufting processes. Eltex EyETM monitors the yarn tension on all positions in real-time and a minimum and maximum allowable tension value can be set. If any yarn’s tension falls outside these values the operator can be warned or the machine stopped.

The Eltex ACT and ACT-R units meanwhile go beyond yarn tension monitoring to actually control yarn tension. This extends the application range greatly. The plug and play system automatically compensates for any differences in yarn tension that arise, for example from irregularities in yarn packages.

Eltex has been owned by Brian Hicks, Seamus O’Dwyer and Jonathan Bell since 2007, following a management buy-out and the subsequent formation of Eltex Global Holdings in Ireland. Today, its head office, Eltex of Sweden AB, is in Osby, Sweden where it provides research and development, administration and global sales for the group. Eltex Manufacturing in Ireland is now the group’s primary production facility and Eltex US, Inc. provides sales and service for North America.

Source:

Eltex of Sweden

MACH2®XS Photo SHIMA SEIKI MFG., LTD.
MACH2®XS
28.01.2024

SHIMA SEIKI at Dhaka International Textile & Garment Machinery Exhibition 2024

Operating in Bangladesh since 1996, this is the fourteenth time the Japanese manufacturer is participating in DTG.

As the Bangladeshi textile industry calls for sustainable production through innovation and digitalization, the market is keen to establish effective business models that support such production. In response, for the first time in its DTG exhibition history, SHIMA SEIKI's lineup consists entirely of WHOLEGARMENT® knitting machines. Capable of knitting an entire garment in one piece without the need for linking or sewing while using only the material required to knit one garment at a time, WHOLEGARMENT® knitting is famous for promoting sustainability in the knit factory.

Operating in Bangladesh since 1996, this is the fourteenth time the Japanese manufacturer is participating in DTG.

As the Bangladeshi textile industry calls for sustainable production through innovation and digitalization, the market is keen to establish effective business models that support such production. In response, for the first time in its DTG exhibition history, SHIMA SEIKI's lineup consists entirely of WHOLEGARMENT® knitting machines. Capable of knitting an entire garment in one piece without the need for linking or sewing while using only the material required to knit one garment at a time, WHOLEGARMENT® knitting is famous for promoting sustainability in the knit factory.

The company is showing its MACH2®XS153 WHOLEGARMENT® knitting machine in 15L gauge, as well as its SWG®091N2 "Mini" WHOLEGARMENT® knitting machine in 15 gauge. MACH2®XS features 4 needle beds and SHIMA SEIKI's original SlideNeedle™, capable of producing high-quality fine gauge WHOLEGARMENT® knitwear in all needles. SWG®091N2 provides opportunities in WHOLEGARMENT® knitting across a wide range of items in a compact, economical package. A different approach to WHOLEGARMENT knitting is also shown in the form of the N.SVR®183 machine. SHIMA SEIKI's global standard in shaped knitting, the N.SVR® series now features a model for producing WHOLEGARMENT® knitwear using every other needle in fine gauge. Shown in 18 gauge at DTG, N.SVR®183 is the ideal machine for flexible, entry-level WHOLEGARMENT® production, with the versatility to respond to fluctuating market demand.

Demonstrations are performed on SHIMA SEIKI's SDS®-ONE APEX4 design system. At the core of the company’s "Total Fashion System" concept, it provides comprehensive support throughout the supply chain, integrating production into one smooth and efficient workflow from yarn development, product planning and design, to machine programming, production and even sales promotion.

Source:

SHIMA SEIKI MFG., LTD.

Teams from Lonati, Lubrogamma and Vickers during a recent meeting at the Vickers HQ in Leeds, UK. Photo: AWOL
Teams from Lonati, Lubrogamma and Vickers during a recent meeting at the Vickers HQ in Leeds, UK.
15.01.2024

Vickers Oils: Reliable running for Lonati’s knitting machines

BTMA member Vickers Oils has marked an important milestone in its partnership with knitting machinery leader Lonati by earning Original Equipment Manufacturer (OEM) approval for its VICKERLUBE SOCK 46 needle oil.

VICKERLUBE SOCK 46 is a mineral-based needle lubricant designed to meet the criteria for modern knitting machine technology. It provides a high standard of lubrication as well as holding very good stability properties and having a high resistance to oxidation. The product is readily scourable and holds a well-balanced additive system meaning that it is fully compatible with all machine components. It can also be used with machines producing any yarn type – including tricky elastanes – to produce the highest quality end product.

Lonati, headquartered in Brescia, Italy, has been a prominent name in knitting machines for over 70 years, designing and manufacturing an impressive average of 8,000 annually. It places a strong emphasis on delivering the highest quality textile machinery, underpinned by a commitment to research and development that ensures the use of cutting-edge products, technologies and processes in its machines.

BTMA member Vickers Oils has marked an important milestone in its partnership with knitting machinery leader Lonati by earning Original Equipment Manufacturer (OEM) approval for its VICKERLUBE SOCK 46 needle oil.

VICKERLUBE SOCK 46 is a mineral-based needle lubricant designed to meet the criteria for modern knitting machine technology. It provides a high standard of lubrication as well as holding very good stability properties and having a high resistance to oxidation. The product is readily scourable and holds a well-balanced additive system meaning that it is fully compatible with all machine components. It can also be used with machines producing any yarn type – including tricky elastanes – to produce the highest quality end product.

Lonati, headquartered in Brescia, Italy, has been a prominent name in knitting machines for over 70 years, designing and manufacturing an impressive average of 8,000 annually. It places a strong emphasis on delivering the highest quality textile machinery, underpinned by a commitment to research and development that ensures the use of cutting-edge products, technologies and processes in its machines.

Vickers Oils, based in Leeds, West Yorkshire, shares these values, leading the industry in quality and assurance through its continuous focus on research and development, technological leadership, quality control and customer service. As it has done for almost two centuries – the company will mark its 200th anniversary in 2028.

Lonati is now officially recommending VICKERLUBE SOCK 46 for use in its single-cylinder GOAL series of knitting machines, marking a successful collaboration that required dedicated efforts from the teams of Lonati, Vickers Oils and its Italian representative Lubrogamma. Vickers Oils is committed to sustainable product development and VICKERLUBE SOCK 46 meets the clearly defined criteria set out by the Global Organic Textile Standard (GOTS) and conforms to ZDHC MRSL Level 1 certification.

Source:

AWOL Media

flat knitting machine © Knitwear Lab
09.01.2024

Knitwear Lab relies on CREATE PLUS patterning software by STOLL

The Dutch company Knitwear Lab helps visions become reality. The creative think tank offers capacities in the areas of R&D, design, knitwear development and production of prototypes and small quantities and has thus implemented a wide range of projects in recent years. The objects range from medical products and high-tech sportswear to smart textiles with integrated sensors. Sustainability activities are also part of the repertoire, such as the production of yarns from recycled waste.

The Dutch company Knitwear Lab helps visions become reality. The creative think tank offers capacities in the areas of R&D, design, knitwear development and production of prototypes and small quantities and has thus implemented a wide range of projects in recent years. The objects range from medical products and high-tech sportswear to smart textiles with integrated sensors. Sustainability activities are also part of the repertoire, such as the production of yarns from recycled waste.

Knitwear Lab operates at two locations for its diverse tasks: Almere in the Netherlandsis available for development work. In Istanbul, there is a branch for production. Both Knitwear Lab sites each have five STOLL flat knitting machines, including models from the modern ADF range. Prototypes are produced in Almere and there is small-scale production. The production plant in Istanbul specializes in the manufacture of high-quality knitwear in small quantities. STOLL is also involved in the creative processes. For the industrial development of knitwear, Knitwear Lab offers Virtual Knitting, a revolutionary method that combines virtual and physical elements of pattern development and knitwear production to reduce waste and pre-production steps. Customers can use Virtual Knitting to create realistic, producible collections, simplify their design iteration processes and take advantage of the wide range of real-life colorways. The basis for this is comprehensive knitwear expertise, the latest 3D software and the CREATE PLUS patterning software, which was developed by STOLL together with KM.ON.

"The 3D visualization of CREATE simplifies communication with the customer considerably. We use this function every day," says Annika Klaas, Senior Knitwear Programmer. She personally appreciates the uncomplicated grading and exchange of stitch dimensions and the much faster and more efficient work with Dimensioned Shapes that this makes possible. This helps her in her day-to-day work. "We often have requests to realize the same product in different yarns, which now works much faster," says the programmer. Further simplifications would include minor optimizations in terms of the efficiency and user-friendliness of programming and additional import and export options for shapes. Discussions on implementation are already underway.

Source:

KARL MAYER GROUP

28.12.2023

ITMA ASIA + CITME: A success for VDMA member companies

This year’s edition of ITMA ASIA + CITME proved to be a success for the exhibiting VDMA member companies. Measured by booked square metres, Germany had the largest contingent, among the foreign exhibitors. More than 40 VDMA member companies were exhibiting their innovative products in Shanghai.

Dr. Janpeter Horn, chairman of the VDMA Textile Machinery Association noted: “Although facing a difficult market situation, this year’s edition of ITMA ASIA + CITME has exceeded the expectations, both in terms of the number of visitors and the quality of the talks. The significant number of foreign visitors to the fair was particularly pleasing.”

Solutions were demonstrated for more sustainable textile productions by most of the exhibitors, and here the VDMA members presented their technologies for saving water, energy and raw materials under the heading “Smart technologies for green textile production.”  

This year’s edition of ITMA ASIA + CITME proved to be a success for the exhibiting VDMA member companies. Measured by booked square metres, Germany had the largest contingent, among the foreign exhibitors. More than 40 VDMA member companies were exhibiting their innovative products in Shanghai.

Dr. Janpeter Horn, chairman of the VDMA Textile Machinery Association noted: “Although facing a difficult market situation, this year’s edition of ITMA ASIA + CITME has exceeded the expectations, both in terms of the number of visitors and the quality of the talks. The significant number of foreign visitors to the fair was particularly pleasing.”

Solutions were demonstrated for more sustainable textile productions by most of the exhibitors, and here the VDMA members presented their technologies for saving water, energy and raw materials under the heading “Smart technologies for green textile production.”  

Dr. Uwe Rondé, CEO, Saurer Intelligent Technology AG explained: “Saurer is satisfied with both the number of visitors and the quality of the discussions. Our booth was full from morning to evening with customers focused on latest technologies within the three mega trends: recycling, automation and digitalisation. Although machine utilisation in the spinning mills is still well below average, people are already gathering information and thinking about what to invest in once the market recovers.”

Benjamin Reiners, owner of Reiners + Fürst stated: „This year’s ITMA ASIA + CITME has exceeded our expectations by far. Especially the first day - a Sunday - has brought many high-quality customers and exclusively decision makers to our booth. We estimate about 20% international customers mainly from Bangladesh, Egypt, India, Iran, Pakistan, Uzbekistan and Vietnam. All customers agreed that the market situation at the moment is difficult, capacity usage is between 50-75% in the ring spinning sector and improvement is expected not before the 2nd half of 2024. Nevertheless the general spirit is very positive.“

“This ITMA ASIA was a great success for Trützschler. We welcomed a large number of Chinese visitors to our booth, as well as a significant number of interested international visitors”, said Dr. Bettina Temath, Head of Global Marketing Trützschler Group SE.

Georg Stausberg, CEO of the polymer processing solutions division and chief sustainability officer of the Oerlikon Group stated: „We can look back on a successful show where we were able to meet many of our customers not only from China, but also from Pakistan, India and Indonesia, for example.”

“A very well-attended trade fair, with interesting discussions, great innovative topics, in line with the modern and rapidly developing China" noted Wolfgang Schöffl, head of product line weaving machines and member of the extended management, Lindauer Dornier.

The VDMA Textile Machinery Association and VDMA China were present at the fair, to support the members e.g. with regard to IPR. With the help of a VDMA expert and a contracted law firm, the member company Sahm submitted a complaint application for patent infringement disputes during the exhibition to the onsite IPR office. Both parties, Sahm, and the Chinese company, that used patented design without permission reached an agreement: The Chinese company had to stop displaying functions and designs involving patent infringement on site which meant the removal of some structural parts and the covering of key components protected by patent protection.

Dr. Harald Weber, managing director of VDMA Textile Machinery concluded: “Asia, and China in particular, represent the primary foreign markets for the VDMA member companies in the sector. The Chinese market is the main destination for their exports. Other major export destinations in Asia include India, Pakistan, Bangladesh and Uzbekistan. ITMA ASIA + CITME provides a unique platform to showcase technologies for customers directly in Asia. The VDMA member companies are looking forward to the coming edition of the fair from 14 to 18 October 2024 in Shanghai.”

The latest survey of VDMA members' subsidiaries in China gives reason to hope that the economic situation in the Chinese textile industry could also improve significantly in the second half of the year. In addition, European textile machinery manufacturers are urged to be present on the most important market and at the trade fair and to offer Asian customers most advanced technology for their demanding challenges.

Source:

VDMA e. V.
Textile Machinery

15.12.2023

Italian textile machinery industry at Colombiatex 2024

At the upcoming edition of Colombiatex, that will take place in Medellin from January 23 to 25, 2024, the leading Italian manufacturers of textile machinery will be present in the common area organized by Italian Trade Agency and ACIMIT, the Association of Italian Textile Machinery Manufacturers.

There will be 23 companies exhibiting in the Italian pavilion. Among these, ACIMIT members companies are: Btsr, Color Service, Danti, Fadis, Flainox, Isotex, Itema, Kairos Engineering, Lgl, Lonati, Mcs, Monti-Mac, Nexia, Orox, Ratti, Reggiani Macchine, Salvadè, Santoni, Srs, Stalam, Tecnorama, Ugolini.

The Colombian textile and clothing industry has experienced significant growth in recent years. Consequently, imports of textile machinery have also increased. In 2023, Colombian imports are expected to reach 58 million euros. For the period 2024-2027, the Country’s import growth is projected to be an average of 2.2% annually, according to data compiled by ACIMIT.

At the upcoming edition of Colombiatex, that will take place in Medellin from January 23 to 25, 2024, the leading Italian manufacturers of textile machinery will be present in the common area organized by Italian Trade Agency and ACIMIT, the Association of Italian Textile Machinery Manufacturers.

There will be 23 companies exhibiting in the Italian pavilion. Among these, ACIMIT members companies are: Btsr, Color Service, Danti, Fadis, Flainox, Isotex, Itema, Kairos Engineering, Lgl, Lonati, Mcs, Monti-Mac, Nexia, Orox, Ratti, Reggiani Macchine, Salvadè, Santoni, Srs, Stalam, Tecnorama, Ugolini.

The Colombian textile and clothing industry has experienced significant growth in recent years. Consequently, imports of textile machinery have also increased. In 2023, Colombian imports are expected to reach 58 million euros. For the period 2024-2027, the Country’s import growth is projected to be an average of 2.2% annually, according to data compiled by ACIMIT.

Italy has long been a technological partner for Colombian textile companies that have invested in the modernization of the production process. Italian exports to Colombia in 2022 exceeded 18 million euros (a 50% increase from the previous year). In the first six months of 2023, Italian exports to Colombia reached 9 million euros.

More information:
ACIMIT Colombiatex
Source:

ACIMIT

06.11.2023

Mahlo presents new solutions at ITMA Asia 2023

Mahlo GmbH + Co. KG will present its systems and solutions for efficient and high-quality textile production and finishing together with Shanghai Kuantex at ITMA Asia (November 19 and 23). The focus will be on the machine manufacturer's new straightening concept, the Orthopac RXVMC.

"In the new straightening concept, special attention was paid to the straightening mechanics and their interaction with the analysis electronics of the probe system," explains Sales Manager Thomas Höpfl. The control concept is also new. A probe group at the leveler infeed detects distortions even before they reach the correction rolls. In this way, the rolls are brought directly into position and the fabric is corrected from the very first centimeter. A scanner group at the outfeed also detects possible residual distortion, which is corrected at the second straightening module. This enables an even more precise and faster response when it comes to reacting to rapidly changing distortions. The Orthopac RXVMC therefore shows its full strength when straightening knitwear and fabrics sensitive to distortion.

Mahlo GmbH + Co. KG will present its systems and solutions for efficient and high-quality textile production and finishing together with Shanghai Kuantex at ITMA Asia (November 19 and 23). The focus will be on the machine manufacturer's new straightening concept, the Orthopac RXVMC.

"In the new straightening concept, special attention was paid to the straightening mechanics and their interaction with the analysis electronics of the probe system," explains Sales Manager Thomas Höpfl. The control concept is also new. A probe group at the leveler infeed detects distortions even before they reach the correction rolls. In this way, the rolls are brought directly into position and the fabric is corrected from the very first centimeter. A scanner group at the outfeed also detects possible residual distortion, which is corrected at the second straightening module. This enables an even more precise and faster response when it comes to reacting to rapidly changing distortions. The Orthopac RXVMC therefore shows its full strength when straightening knitwear and fabrics sensitive to distortion.

Also contributing to high-quality textile production and finishing is the Famacont PMC for controlling weft and stitch course density, which will also be on show at ITMA Asia. The Famacont PMC-15 uses a sensor to measure the yarn or stitch density and compares it with the target value stored in the recipe data management system. The detected deviation of the yarn density from the target value is used to fully automatically regulate the leading during the needling process on the stenter frame. Interested parties can have the mode of operation explained to them at the Mahlo booth with the help of a demo tower and their own or provided fabric samples.

Another major topic remains Industry 4.0, because the best measured data is of no use if it cannot be utilized. Mahlo has continuously developed its digital environment mSmart. "Our systems generate data that the customer can use immediately to regulate goods on-line. At the same time, all measured values are backed up in our data management system mLog enhanced and can be retrieved at any time. With this historical data, processes can be optimized and weak points in the process can be minimized," explains Sales Manager Thomas Höpfl.

18.10.2023

SHIMA SEIKI at A+A 2023

SHIMA SEIKI MFG., LTD. of Wakayama, Japan will participate in the A+A 2023—Safety, Security and Health at Work International Trade Fair in Düsseldorf, Germany (24th-27th October 2023). On display will be the company's latest safety-related technology through its new SPG®-R pile glove knitting machine and the prototype SFG®-R next-generation glove knitting machine. Each of these machines drew attention at SHIMA SEIKI's booth at the International Textile Machinery (ITMA 2023) Exhibition in Milan.

SHIMA SEIKI MFG., LTD. of Wakayama, Japan will participate in the A+A 2023—Safety, Security and Health at Work International Trade Fair in Düsseldorf, Germany (24th-27th October 2023). On display will be the company's latest safety-related technology through its new SPG®-R pile glove knitting machine and the prototype SFG®-R next-generation glove knitting machine. Each of these machines drew attention at SHIMA SEIKI's booth at the International Textile Machinery (ITMA 2023) Exhibition in Milan.

SHIMA SEIKI's original SPG®, developed in 1979 as the world’s first automatic glove knitting machine to produce seamless pile-knitted gloves, is now reborn as a next-generation model. Pile gloves feature special traits that include cushioning, shock-reduction and thermal insulation and cold protection, making them popular especially in the field of industrial safety. Now, SPG® is redesigned from the ground up and re-introduced as the SPG®-R. The new SPG®-R features a new moveable sinker system with selectable loop presser function. Combined with a new belt-driven carriage it allows SPG® to provide efficient and reliable production of fashionable, high-quality pile gloves. Shown in 7 gauge at A+A, SPG®-R surpasses the previous generation with pioneering technology, improved capability and reliable productivity.

SHIMA SEIKI's original product on which the company was founded was the fully automated seamless glove knitting machine. While the original model evolved to become the current SFG® series, SFG®-R exhibited at A+A is its spiritual successor. With a new sinker system, a belt-driven 2-cam carriage and auto yarn carriers SFG®-R is a completely new machine for knitting gloves that conform better to the shape of the hand for improved fit. Furthermore its greater design potential offers users the opportunity to break out of the work glove market and into the fashion market. SFG®-R is shown as a prototype next-generation model in 12 gauge at A+A.

Also demonstrated will be SHIMA SEIKI's APEXFiz® design software. The importance of design software is made even more significant by the new patterning capabilities of SPG®-R and SFG®-R. Both machines now feature increased design potential that allow each of their products—pile gloves and work gloves, respectively—to expand their market into fashion. APEXFiz® is available for developing these designs. Furthermore virtual sampling on APEXFiz® is especially effective in streamlining the production process. Ultra-realistic simulation capability allows the use of virtual samples for evaluating design variations without producing actual samples for each variation, thereby minimizing the time, cost and resources normally required with sample-making, supporting smart, speedy and sustainable production.

Source:

SHIMA SEIKI MFG., LTD.

21.07.2023

Digital Textile Printing: Direct-to-Film Technology

In the printing industry, direct-to-film technology is having a transformative impact on the apparel decoration space. It provides a simple and affordable garment printing process that facilitates vibrant, dynamic, full-colour designs with a durable print. It opens up opportunities for digital print service providers (PSPs) to expand their product offerings in the textile industry, their network of potential customers and expand the range of fabrics they can print on.

In the printing industry, direct-to-film technology is having a transformative impact on the apparel decoration space. It provides a simple and affordable garment printing process that facilitates vibrant, dynamic, full-colour designs with a durable print. It opens up opportunities for digital print service providers (PSPs) to expand their product offerings in the textile industry, their network of potential customers and expand the range of fabrics they can print on.

Direct-to-film vs. Screen Printing
Direct-to-film printing is the process of digitally printing directly onto a special transfer film sheet. The printed film is subsequently sprinkled with a hot-melt powder and heated. Once the transfer sheet is cured and dried, it can be heat-pressed onto a variety of fabrics to create premium transferred designs for customised merchandising, sportswear, and an array of other promotional applications for the textile market. Compared with traditional screen printing, the plate creation required for that process is far too time-consuming. Not only this, but it does not match direct-to-film’s ability to produce vivid colours and quality details such as shapes, lettering, and motifs often sought after in the promotional and merchandising space for bespoke textiles.

The Mimaki TxF150-75
Mimaki’s first direct-to-film inkjet printer is the TxF150-75, a fitting extension to the 150 series, with a maximum printing width of 80cm. Offering a stable printing plotter, the model’s built-in ink circulation system and degassed ink pack are resolutions to common direct-to-film challenges such as poor ink ejection and white ink clogging. The new printer also includes core Mimaki features including NCU (Nozzle Check Unit) and NRS (Nozzle Recovery System) for stable, uninterrupted print production. Operating in harmony with the textile printer itself is Mimaki’s ECO PASSPORT by OEKO-TEX® certified water-based pigment textile inks, formulated especially for the TxF150-75. Coupled with Mimaki’s RasterLink7 RIP software, users are offered end-to-end oversight and efficiency from creative design to final product.

In addition, and in line with Mimaki’s collaborative approach to meeting customer needs, Adkins has developed an 80cm wide powder shaker cure unit to complete this ‘A brand’ direct-to-film printing solution. By offering the printer and post-processing unit at 80cm wide, customers can print larger garments with less waste and quicker production times, making the process much more cost effective.

STOLL launches a new innovation package (c) STOLL, KARL MAYER GROUP
07.07.2023

STOLL launches a new innovation package

ITMA 2023 was a successful platform for the flat knitting machine manufacturer STOLL to present its latest new developments. The business unit of the KARL MAYER GROUP will be following up this fair on 3 July with the launch of a further innovation package. With the solutions contained in this package, STOLL will be offering its customers additional added value when using their flat knitting machines - in line with the concept of bundling innovations.

ITMA 2023 was a successful platform for the flat knitting machine manufacturer STOLL to present its latest new developments. The business unit of the KARL MAYER GROUP will be following up this fair on 3 July with the launch of a further innovation package. With the solutions contained in this package, STOLL will be offering its customers additional added value when using their flat knitting machines - in line with the concept of bundling innovations.

The new features include an optimised central lubrication system that reduces both maintenance effort and oil consumption, this as standard from July 2023 for all models of the CMS and ADF series produced in Reutlingen.
Compared to the previous optional variant, it ensures more efficient and comprehensive lubrication. All needle bed elements, from the holding-down jack to the coupling part and intermediate slider to the selection jack, are now supplied with oil. The machine itself recognises whether lubrication is required. Independently of this, the lubrication intensity and oil distribution can be adapted to the individual machine conditions by setting various parameters, if required. To ensure that the required amount of lubricant is reliably supplied, a message is sent if the level is too low.

In addition, a new oil drain container as standard equipment for all CMS and ADF models catches used oil from the needle bed under the machine. This prevents soiling of floors or knitted fabrics. The emptying of the container can be efficiently managed by an adjustable reminder function. The neat and at the same time sustainable solution does not require cleaning agents or hoovers and offers the possibility to reuse the oil after cleaning through special filters, if necessary.

Users of CMS and ADF belt take-down machines can benefit from optimisations around the belt take-down. Thanks to the new STOLL innovation package, this can be turned forwards and backwards by means of a switch as standard in order to easily eliminate fabric wraps and thus reduce maintenance times. In addition, a mirror, which is also fitted as standard, ensures a simple visual check of the belt take-down.

Another solution of the STOLL innovation package from July 2023 includes new cams that enable split-stitch implementation without cam box modification. This reduces manual effort and thus conversion times and costs. The feature is standard on all fine gauges ADF and CMS machines.

For the W machines from STOLL, there is now a further inlay yarn carrier, the Qt, in addition to the previous Qw yarn carrier. The extension means that the number of inlay yarn carriers used in a system can be increased from the previous one to three. No additional system is required for the weft yarn, and the process steps weft yarn insertion and knitting take place in the same system.

Source:

KARL MAYER Verwaltungsgesellschaft mbH

(c) Mayer & Cie. GmbH & Co. KG
05.07.2023

Mayer & Cie. draws positive balance on ITMA 2023

From circular knitting machines and braiders via upgrades to digital solutions, Mayer & Cie. presented at ITMA 2023 a wide range of solutions that make circular knitting machines and braiding machines even more durable and thereby more valuable, for which the long-established firm received a positive visitor response.

From machinery manufacturer to solution provider
Three circular knitting machines – a Relanit 3.2 HS, an SF4-3.2 III and the OVJA 2.4 EM – and an MR-15/18C/Single Deck braiding machine took up about half the floor space of Mayer & Cie.’s ITMA stand. That reflected the weighting of the trade fair presentation. Along with high-tech circular knitting and braiding products the Mayer & Cie. focus at this year’s ITMA was on solutions that increase the value and durability of its machines. Including the digital platform knitlink, the new Control 5.0 machine control system, the camera-assisted error recognition system knithawk, almost a dozen upgrade kits for existing machines and the new oiler system Senso Blue RS.

From circular knitting machines and braiders via upgrades to digital solutions, Mayer & Cie. presented at ITMA 2023 a wide range of solutions that make circular knitting machines and braiding machines even more durable and thereby more valuable, for which the long-established firm received a positive visitor response.

From machinery manufacturer to solution provider
Three circular knitting machines – a Relanit 3.2 HS, an SF4-3.2 III and the OVJA 2.4 EM – and an MR-15/18C/Single Deck braiding machine took up about half the floor space of Mayer & Cie.’s ITMA stand. That reflected the weighting of the trade fair presentation. Along with high-tech circular knitting and braiding products the Mayer & Cie. focus at this year’s ITMA was on solutions that increase the value and durability of its machines. Including the digital platform knitlink, the new Control 5.0 machine control system, the camera-assisted error recognition system knithawk, almost a dozen upgrade kits for existing machines and the new oiler system Senso Blue RS.

Trade fair debut for Mayer & Cie. braiding machine
Mayer & Cie. also exhibited a braiding machine at ITMA for the first time. The company has integrated the braiding division at is Albstadt headquarters since 2019. “Braiding machines are a part of textile machinery,” said Mayer & Cie. Managing Partner Benjamin Maye, “but we nevertheless saw presenting the MR-15/18C/SD braider at ITMA as an experiment – and are satisfied with the result. The machine attracted a great deal of attention and we were able to make interesting contacts.”

A positive conclusion on ITMA 2023
Expectations of this year’s ITMA were moderate, Benjamin Mayer said. “War, high energy prices, inflation and recession are the signs of the times. Not even an ITMA is going to change that.” In addition, there had been serious problems with the issue of visas that had made it impossible for many potential visitors to attend the trade fair.

The Mayer & Cie. management therefore judged its success not by the general demand but by the positive visitor feedback. “For us that was an indicator of our future competitiveness,” said CEO Benjamin Mayer, “and we can definitely be sure of that with our developments.”

Source:

Mayer & Cie. GmbH & Co. KG

19.06.2023

SHIMA SEIKI to exhibit at Pitti Filati

SHIMA SEIKI ITALIA S.p.A., Italian subsidiary of leading Japanese computerized knitting solutions provider SHIMA SEIKI MFG., LTD., will exhibit at the 93rd edition of the Pitti Immagine Filati exhibition in Florence, Italy. It will exhibit as part of the new CustomEasy section, which explores the various aspects of customization in the presence of textile machinery, including a multi-faceted lineup of SHIMA SEIKI WHOLEGARMENT® knitting machines.

SHIMA SEIKI ITALIA S.p.A., Italian subsidiary of leading Japanese computerized knitting solutions provider SHIMA SEIKI MFG., LTD., will exhibit at the 93rd edition of the Pitti Immagine Filati exhibition in Florence, Italy. It will exhibit as part of the new CustomEasy section, which explores the various aspects of customization in the presence of textile machinery, including a multi-faceted lineup of SHIMA SEIKI WHOLEGARMENT® knitting machines.

The WHOLEGARMENT® knitting machine SWG-XR® features 4 needle beds for all-needle knitting of high quality WHOLEGARMENT® products using the company's original SlideNeedle™. SWG-XR® features a re-designed sinker system and a compact, light-weight carriage featuring 4 systems as well as auto yarn carriers. All contribute to increased productivity of more than 25% over the previous MACH2®XS machine, as well as increased product range using a wider variety of yarn for supporting knits for all seasons, and higher quality for knitting beautiful fabrics and silhouettes; even items that were impossible to knit with the MACH2® series, including punch-lace patterns, variable stitch knitting and intarsia knitting. Setting new standards for the next generation of waste-free, sustainable WHOLEGARMENT® knitting, SWG-XR® at Pitti Filati will be shown in 18L.

Affectionately referred to as “SWG®-Mini,” SHIMA SEIKI's compact line of WHOLEGARMENT® machines allows customers to take advantage of the same short lead times and versatile production as larger WHOLEGARMENT® knitting machines, but with minimal investment. SWG®091N2 with its 36-inch (90cm) knitting width is especially suited to knitting a wide variety of items including accessory items as well as childrenswear and smaller size garments, all without the need for linking or sewing afterward. At Pitti Filati SWG®091N2 will be shown in 5 gauge.

A new proposal in WHOLEGARMENT® knitting will also be shown in the form of the N.SVR®183 WHOLEGARMENT® knitting machine. SHIMA SEIKI's global standard in shaped knitting, the N.SVR® series now features a model for producing WHOLEGARMENT® knitwear using every other needle in fine gauge. N.SVR®183 is equipped with the R2CARRIAGE® system and a compact, lightweight carriage for even higher productivity. Shown in 21G at Pitti Filati 93, N.SVR®183 is the ideal machine for flexible, entry-level WHOLEGARMENT® production, with the versatility to respond to fluctuating market demand.

APEXFiz® subscription-based design software supports the creative side of fashion from planning and design to colorway evaluation, realistic fabric simulation and 3D virtual sampling. Virtual samples are a digitized version of sample making that are accurate enough to be used effectively as prototypes. By replacing physical samples, virtual samples reduce time, cost and material that otherwise go to waste. APEXFiz® thereby helps to realize sustainability and digitally transform the fashion supply chain.

Continuing from past editions of Pitti Filati are knit samples produced in collaboration with Italian designer Vittorio Branchizio, as well as samples from SHIMA SEIKI headquarters for assessing the potential of SHIMA SEIKI knitting machines.

Source:

SHIMA SEIKI MFG., LTD.

14.06.2023

Spinnova and Portuguese Tearfil agree on an R&D yarn-spinning line

Spinnova has entered into a yarn development cooperation agreement with the Portuguese company Tearfil, where Tearfil will operate Spinnova’s R&D yarn-spinning line. The yarn-spinning line is intended for product development and will be located in Guimarães, Portugal at Tearfil's facilities.  

The rationale behind the yarn-spinning line is for research and development into using Spinnova's fibre in commercial scale yarn production and to streamline development work with industry partners.   
Spinnova has decided to locate the line in Guimarães in Portugal, at Tearfil’s facilities. Spinnova will benefit from the industry know-how of a strong partner and from the proximity of one of Europe’s most significant textile industry hubs in Portugal. This will improve Spinnova’s access to global textile markets.   

Spinnova has entered into a yarn development cooperation agreement with the Portuguese company Tearfil, where Tearfil will operate Spinnova’s R&D yarn-spinning line. The yarn-spinning line is intended for product development and will be located in Guimarães, Portugal at Tearfil's facilities.  

The rationale behind the yarn-spinning line is for research and development into using Spinnova's fibre in commercial scale yarn production and to streamline development work with industry partners.   
Spinnova has decided to locate the line in Guimarães in Portugal, at Tearfil’s facilities. Spinnova will benefit from the industry know-how of a strong partner and from the proximity of one of Europe’s most significant textile industry hubs in Portugal. This will improve Spinnova’s access to global textile markets.   

Spinnova’s yarn-spinning line will be installed at Tearfil's premises. The technology delivery and installations are expected to take place in the fall of 2023, and the spinning line is intended to be operational by the end of the year. Tearfil is responsible for the yarn-spinning line's operations, and Spinnova will use a part of the line capacity for its product development.  

In 2021, Spinnova announced that it would establish an R&D yarn-spinning line in Jyväskylä, Finland. The decision to change the location was made during the feasibility planning and discussions with potential partners. This change in location and operational model will slightly decrease the capital expenditure and will lead to lower operational expenses.  

The technology supplier for Spinnova's new spinning mill line is the Swiss-based company Rieter. Rieter is a leading supplier of systems for manufacturing yarn from staple fibers in spinning mills. The company develops and manufactures machinery, systems and components used to convert natural and man-made fibers and their blends into yarns in the most cost-efficient manner.

More information:
Spinnova Tearfil spinning Portugal
Source:

Spinnova

09.06.2023

EFI Reggiani showcases its innovations at ITMA 2023

At ITMA 2023, EFI™ Reggiani is presenting its sustainable Reggiani ecoTERRA pigment printing line up, the high-speed EFI Reggiani HYPER and Reggiani BOLT XS direct-to-fabric printing solutions, and EFI Inèdit end-to-end digital textile workflows.

At ITMA 2023, EFI™ Reggiani is presenting its sustainable Reggiani ecoTERRA pigment printing line up, the high-speed EFI Reggiani HYPER and Reggiani BOLT XS direct-to-fabric printing solutions, and EFI Inèdit end-to-end digital textile workflows.

The EFI Reggiani ecoTERRA solution is an all-in-one solution for water-based pigment printing that requires no ancillary equipment for pre- and post-treatment. By reducing water, energy and chemicals consumption in the overall process, customers can now obtain a sustainable, direct-to-fabric printing solution. For the first time at ITMA, EFI Reggiani is presenting its full ecoTERRA line up of four models, including a 340 printing width, with speeds ranging from 150 to 600 sqm/hour. This allows customers to choose the best TCO/ROI based on output volume and speed range.
 
Reggiani ecoTERRA water-based pigment inks deliver excellent wet and dry fastness properties, sharpness in detail, and durability while also ensuring printhead longevity with reduced maintenance costs. Thanks to the enhanced polymerisation and finishing unit, EFI Reggiani ecoTERRA also provides an enhanced tactile experience and fabric softness.
 
In addition to highlighting EFI Reggiani’s sustainable product offering, the company will also demonstrate the significant productivity and efficiency advantages offered by its portfolio of high-speed, high-performance digital textile printers at ITMA 2023. Attendees will discover how mass production can transition to a digital, on-demand workflow with the high speeds and high print quality of the EFI Reggiani HYPER scanning printer and the next-generation EFI Reggiani BOLT XS single-pass textile printer.

Visitors to the booth also will see EFI Reggiani’s new proprietary end-to-end digital printing workflow and the latest enhancements to EFI Inèdit digital textile software. Inèdit, now part of EFI Reggiani, is one of the leading developers of raster image processors (RIPs) and related software for digital industrial textile printing. The EFI Reggiani end-to-end workflow with Inèdit integration boosts productivity and production capabilities for digital textile print operations while ensuring maximum security for customer’s designs thanks to two-level encryption.
 
EFI Reggiani QUERY, the user-friendly, advanced data analysis tool to measure printer performance, keep track of real costs per metre, and monitor water and energy consumption, will also be demonstrated.

(c) Mimaki
09.06.2023

Mimaki launches Tiger600-1800TS Dye Sublimation Printer

Mimaki Europe, a provider of industrial inkjet printers, cutting plotters, and 3D printers, is debuting the new Tiger600-1800TS, Mimaki’s most productive sublimation transfer printer, on its stand at ITMA 2023. This latest high-speed, compact and robust roll-to-roll inkjet printer has been designed to accelerate the analogue to digital transformation within the textile printing industry.

The Tiger600-1800TS boasts a maximum printing speed of 550 m2/h (143% faster than the previous model) owing to the renovated high-speed printhead and Mimaki’s proprietary image quality enhancement technologies. The printer’s size has also been halved compared to the previous system, with the paper mounting and winding system both located at the back of the machine. This smaller footprint enables customers to easily install multiple units to meet fluctuating demand, whilst also increasing overall production capacity.

Mimaki Europe, a provider of industrial inkjet printers, cutting plotters, and 3D printers, is debuting the new Tiger600-1800TS, Mimaki’s most productive sublimation transfer printer, on its stand at ITMA 2023. This latest high-speed, compact and robust roll-to-roll inkjet printer has been designed to accelerate the analogue to digital transformation within the textile printing industry.

The Tiger600-1800TS boasts a maximum printing speed of 550 m2/h (143% faster than the previous model) owing to the renovated high-speed printhead and Mimaki’s proprietary image quality enhancement technologies. The printer’s size has also been halved compared to the previous system, with the paper mounting and winding system both located at the back of the machine. This smaller footprint enables customers to easily install multiple units to meet fluctuating demand, whilst also increasing overall production capacity.

A further environmental benefit of the Tiger600-1800TS will be the bluesign® certification of its MLSb510 series sublimation transfer inks. This certificate, expected to be awarded in June 2023, will provide assurance that these inks are of highest quality combined with due consideration for the safety of consumers and print operators, and environmental conservation, and therefore, contributing to the sustainability of the textile industry.

Mimaki’s expertise in developing reliable, easy-to-use and efficient solutions has also not faltered in the development of the Tiger600-1800TS. The printer’s ink tanks can be replaced without interrupting the printing process, minimising down time. Maintenance of the printer is also reduced with its roller paper feeding method eliminating the need for the application of adhesives onto a belt.

Source:

Mimaki Europe

09.06.2023

EURATEX: Meeting about Industry 5.0 concept

On the occasion of EURATEX’ General Assembly held in Milan on 7 June, the European textile industry  discussed the relationship between innovation, sustainability and people in the industry of tomorrow. EURATEX members welcomed the Textiles Transition Pathway, released on 6 June by the Commission, as a valuable roadmap to ensure a successful green and digital transition. The meeting in Milan was also the occasion to strengthen links with textile machine manufacturers, gathering at ITMA 2023.

Hosted by Sistema Moda Italia (SMI), EURATEX meetings addressed the crucial issue of how to develop new competitive business models for the future, following the Industry 5.0 concept. In 2021, the European Commission launched “Industry 5.0”, which puts the wellbeing of the worker at the centre of the production process and the use of new technologies to provide prosperity beyond jobs and growth, while respecting the production limits of the planet.

On the occasion of EURATEX’ General Assembly held in Milan on 7 June, the European textile industry  discussed the relationship between innovation, sustainability and people in the industry of tomorrow. EURATEX members welcomed the Textiles Transition Pathway, released on 6 June by the Commission, as a valuable roadmap to ensure a successful green and digital transition. The meeting in Milan was also the occasion to strengthen links with textile machine manufacturers, gathering at ITMA 2023.

Hosted by Sistema Moda Italia (SMI), EURATEX meetings addressed the crucial issue of how to develop new competitive business models for the future, following the Industry 5.0 concept. In 2021, the European Commission launched “Industry 5.0”, which puts the wellbeing of the worker at the centre of the production process and the use of new technologies to provide prosperity beyond jobs and growth, while respecting the production limits of the planet.

The keynote speakers, Francesco Pinto (Chairman, Yamamay) and Claudio Cavacini (Director of Retail Industry Solutions & Strategy, Salesforce), presented how the digital transformation is affecting companies in the retail industry and how they should adapt to maintain their competitive edge. A panel session of textile machinery manufacturers debated how their companies can help delivering this transformation through state of the art machineries. They all agreed that it requires common efforts by all actors and stakeholders along the textile value chain and public support to make the necessary investments. According to Enzo Maurer, ITMA President, ITMA 2023 in Milan will exactly showcase excellence in innovation and new available technologies to make a leap forward in sustainability.

According to Sergio Tamborini, "we are particularly honored to host this event organized by Euratex, the association which is the voice of the European textile industry and its demands, especially those concerning the circular economy. Sistema Moda Italia wants to play its part and there are priorities, from legislation on extended producer responsibility (EPR) in Italy to eco-design, where textiles and clothing will act as a testing ground. SMI's goal will be to continue to encourage the debate on circularity  promoting it in all institutional settings aiming to a growing sustainable  supply chain.”

Alberto Paccanelli, EURATEX President added: “Today’s discussions showed that we are ready to take up new challenges. Nevertheless, this  transition towards a textiles 5.0 can only happen with the support of all actors, from policy makers to retailers. Today’s meeting was also the occasion to review the EU transition pathway for the textiles ecosystem, published yesterday by the European Commission. The pathway is the perfect example of a co-creation process between the European institutions and the stakeholders. We hope that other EU initiatives or legislative proposals will follow the same co-creative process.”

Source:

EURATEX

(c) M. Vorhof, ITM/TU Dresden
12.04.2023

ITM at JEC 2023

From April 25th to 27th, 2023, the Institute of Textile Machinery and High Performance Material Technology (ITM) of TU Dresden will be exhibiting at the pavilion SAXONY! at JEC World 2023.

The ITM will provide a comprehensive overview of its current research in the field of machine and product development along the entire textile process chain.

The upcoming JEC 2023 exhibition will highlight innovative Customised Connective Cores (CCC), which are custom-made core-insert structures additively manufactured using cellular metal and a form-fit integrated insert. These CCCs can be seamless integrated either as patches or as full-surface core material into lightweight panels, offering significantly improved load-bearing behavior (especially 4 times the load-bearing capacity and fail-safe behavior) compared to existing technologies. This breakthrough opens up new possibilities for fastening lightweight panels.

From April 25th to 27th, 2023, the Institute of Textile Machinery and High Performance Material Technology (ITM) of TU Dresden will be exhibiting at the pavilion SAXONY! at JEC World 2023.

The ITM will provide a comprehensive overview of its current research in the field of machine and product development along the entire textile process chain.

The upcoming JEC 2023 exhibition will highlight innovative Customised Connective Cores (CCC), which are custom-made core-insert structures additively manufactured using cellular metal and a form-fit integrated insert. These CCCs can be seamless integrated either as patches or as full-surface core material into lightweight panels, offering significantly improved load-bearing behavior (especially 4 times the load-bearing capacity and fail-safe behavior) compared to existing technologies. This breakthrough opens up new possibilities for fastening lightweight panels.

Another highlight at the exhibition is the repair process for fibre-reinforced composites (FRP) developed at the ITM. Instead of mechanically grinding the damaged area, the matrix in the repair area is locally dissolved using a UV-rays-induced depolymerisation process. Damaged fibres can thus be replaced by a customized repair patch. Free yarn ends on the textile repair patches are spliced with the UV-exposed yarn ends in the repair area using an adapted splicing process. In this way, a very clean, simplified and mechanically improved repair area can be achieved compared to the state of the art.

The diverse possibilities offered by the structure and process simulation of textile high-performance materials and textile manufacturing processes will also be presented. By means of multi-scale modelling and simulation, a profound understanding of materials and processes is achieved at the ITM. Finite element models on the micro, meso and macro scale have been developed and validated for this purpose. Examples from current ITM research projects demonstrate the various possibilities and areas of application of modern simulation methods in the field of textile technology.

Moreover, an innovative process for the integral manufacturing of 3D rib-stiffened preforms with complexly arranged stiffeners in 0°, 90° and ± 45° orientation was developed and successfully implemented at the ITM. Due to the process-integrated structure fixation and the continuous fibre reinforcement between shell and rib structure, the 3D preforms are perfectly suited for the production of highly load-bearing FRP components with increased bending stiffness, which will be exhibited at JEC. Hence, the lightweight construction potential of high-performance fibres can be fully exploited.

A successfully established development are partially flowable 2D textile reinforcement fabrics that are continuously manufactured in one single process step. For this purpose, the entire process chain was developed at the ITM, which allows a cost-effective and high-volume production of load-bearing thermoplastic 3D FRP components with continuous fibre reinforcement between shell and stiffeners.

At JEC 2023, the ITM will also present a partially embedded textile latice girder as reinforcement for carbon concrete applications, which was produced by means of an innovative textile manufacturing process based on the multiaxial warp knitting technology. Through the development of a customized warp insertion, manipulation and take-off system as well as appropriate shaping methods, it is now possible to produce tailored textile semi-finished products, e.g. for use in wall and ceiling panels. These textile latice girders represent a resource-saving alternative to conventional steel girders due to the reduced among of concrete required and the additional cavity for media and cable guidance.

The integration of textile actuators and sensors in FRP provides structures with additional functionalities. The research and application of such interactive FRP with different matrix materials (e.g. with thermoset, elastomer or concrete matrix systems) for structural health monitoring or adaptive systems is one of the key research areas of the ITM.

Moreover, the development and implementation of innovative yarn constructions based on recycled high-performance fibres (e.g. rCF, rGF, rAR) for sustainable FRPs is successfully promoted at ITM. By use of a special carding machine, recycled fibres are opened up, separated and joined to form a wide, uniform ribbon. Subsequently, innovative hybrid yarn constructions made of evenly mixed recycled high-performance and thermoplastic fibres with variable fibre volume fractions can be manufactured by means of various spinning technologies. Selected yarn constructions and components will be showcased at JEC.

More information:
ITM TU Dresden JEC World
(c) Zünd Systemtechnik AG
06.04.2023

ITMA 2023: Zünd presents digital single- ply cutting

At ITMA 2023 in Milan, Zünd is focusing on the advantages of digital single-ply cutting in modern garment production.

At the show, Zünd will demonstrate the advantages of individual cutting on demand and what benefits single-ply cutting of textiles offers. In the course of digitalization, the market environment of the apparel industry has changed. Producers are responding to increasing digitalization and ever-shorter product life cycles by investing in lean and highly automated production workflows. Solutions from Zünd supported process streamlining from ordering to cutting while minimizing manual interventions.

At ITMA 2023 in Milan, Zünd is focusing on the advantages of digital single-ply cutting in modern garment production.

At the show, Zünd will demonstrate the advantages of individual cutting on demand and what benefits single-ply cutting of textiles offers. In the course of digitalization, the market environment of the apparel industry has changed. Producers are responding to increasing digitalization and ever-shorter product life cycles by investing in lean and highly automated production workflows. Solutions from Zünd supported process streamlining from ordering to cutting while minimizing manual interventions.

Zünd's single-ply cutters are the cutting tools in digitized production, offering manufacturers flexibility and profitability. Intelligent automation functions, optical solutions and software tools facilitate resource optimization, keep an eye on material consumption and support employees who can turn their attention to value-adding activities. With digital single-layer cutting, manufacturers speed up their cutting and expand their production capacities at the same time. They can accept orders at very short notice and easily meet delivery times thanks to highly economical and efficiently scalable on-demand production. Peaks in demand can be easily managed.

Zünd cutters give users new flexibility in their production workflow. He can work with complex motifs, demanding textiles and different shapes. The cutting technology enables the apparel industry to produce highly individualized customized garments in small batches and on demand just as economically and efficiently as in high volumes. It can process and handle more orders in less time. At the same time, both material and time are saved. In combination with the MindCut production software and precise single-layer cutting, there is almost no waste. The cut parts can be nested very close to each other and close to the material edges. This not only offers considerable savings potential, but also helps to reduce the ecological footprint.

Source:

Zünd Systemtechnik AG

Photo Fibre Extrusion Technology Ltd (FET)
23.03.2023

FET prepares for INDEX 23 Exhibition in Geneva

Fibre Extrusion Technology Ltd (FET) of Leeds, UK will shortly be exhibiting at INDEX 23, the leading nonwovens exhibition in Geneva, 18-21 April.

As well as featuring its latest meltblown and spunbond technology, FET will focus on its new Fibre Development Centre. Construction and fit-out of this new purpose-built building is now fully operational. This modern two-storey development provides state-of-the-art facilities, including enhanced laboratory for client testing and product development.

Resident equipment in the Fibre Development Centre reflects the wide range of fibre extrusion systems offered by FET to clients across the globe and will enable continued growth of the company through innovation.  

Complementing FET’s highly successful meltblown technology, the more recent spunbond range provides unprecedented opportunities for the scaled development of new nonwoven fabrics based on a wide range of fibres and polymers, including bicomponents.

Fibre Extrusion Technology Ltd (FET) of Leeds, UK will shortly be exhibiting at INDEX 23, the leading nonwovens exhibition in Geneva, 18-21 April.

As well as featuring its latest meltblown and spunbond technology, FET will focus on its new Fibre Development Centre. Construction and fit-out of this new purpose-built building is now fully operational. This modern two-storey development provides state-of-the-art facilities, including enhanced laboratory for client testing and product development.

Resident equipment in the Fibre Development Centre reflects the wide range of fibre extrusion systems offered by FET to clients across the globe and will enable continued growth of the company through innovation.  

Complementing FET’s highly successful meltblown technology, the more recent spunbond range provides unprecedented opportunities for the scaled development of new nonwoven fabrics based on a wide range of fibres and polymers, including bicomponents.

Source:

Fibre Extrusion Technology Ltd (FET)

02.03.2023

VDMA: Way2ITMA

100 days before ITMA 2023 in Milan, VDMA Textile Machinery launched its “Way2ITMA” webinar series. “Transforming the World of Textiles: efficient – digital – circular”. Under this heading, VDMA technology providers will present their solutions along the value chain.

Speakers of the virtual event were Dr. Janpeter Horn, Chairman of the VDMA Textile Machinery Association and Managing Director of August Herzog Maschinenfabrik, Dirk Vantyghem, Director General, EURATEX, Francis Elias Junker, Area Sales Manager, Andritz Laroche and Tanja Karila, Chief Marketing Officer, Infinited Fiber Company.

With regard to the EU strategy for sustainable and circular textiles, Dr. Horn said: “This topic concerns all of us, consumers and producers. We as machinery builders position ourselves as enablers. We want to be part of the solution of this ambitious project”.

100 days before ITMA 2023 in Milan, VDMA Textile Machinery launched its “Way2ITMA” webinar series. “Transforming the World of Textiles: efficient – digital – circular”. Under this heading, VDMA technology providers will present their solutions along the value chain.

Speakers of the virtual event were Dr. Janpeter Horn, Chairman of the VDMA Textile Machinery Association and Managing Director of August Herzog Maschinenfabrik, Dirk Vantyghem, Director General, EURATEX, Francis Elias Junker, Area Sales Manager, Andritz Laroche and Tanja Karila, Chief Marketing Officer, Infinited Fiber Company.

With regard to the EU strategy for sustainable and circular textiles, Dr. Horn said: “This topic concerns all of us, consumers and producers. We as machinery builders position ourselves as enablers. We want to be part of the solution of this ambitious project”.

Dirk Vantyghem introduced the core issues of the EU textile strategy launched in 2022, which is the most ambitious plan ever, to push the textile sector towards sustainability and transparency, and promote a new circular business model. If wrongly designed, that new framework may collapse the European textile value chain. But if done rightly, the changes ahead could bring a paradigm shift in the sector, where competitiveness is no longer based on price only, but also on sustainability and innovation, explained Vantyghem.

Francis Elias Junker showed high level of expertise for mechanical textile recycling for both spinning and nonwovens industries that Andritz has. The company has a diversity of solutions to offer and several cooperation partners, covering the value chain from recovery of fiber to the chemical modification and preparation for the production of yarn.

Tanja Karila gave an overview of how Infinited Fiber is turning textile waste into new fibers. Patented technology turns post-consumer textile waste into brand new premium quality fibers for the textile industry. The textile-to-textile recycling technology captures the value in waste that would otherwise be landfilled or burned.

More information:
ITMA 2023 Sustainability Webinar
Source:

VDMA e. V.
Textile Machinery