Textination Newsline

Reset
35 results
Photo: TheDigitalArtist, Pixabay
31.01.2024

“Smart nanocomposites” for wearable electronics, vehicles, and buildings

  • Small, lightweight, stretchable, cost-efficient thermoelectric devices signify a breakthrough in sustainable energy development and waste heat recovery.
  • Next-gen flexible energy harvesting systems will owe their efficiency to the integration of graphene nanotubes. They offer easy processability, stable thermoelectric performance, flexibility, and robust mechanical properties.
  • Nanocomposites have high market potential in manufacturing generators for medical and smart wearables, vehicles sensors, and efficient building management.

Around half of the world’s useful energy is wasted as heat due to the limited efficiency of energy conversion devices. For example, one-third of a vehicle’s energy dissipates as waste heat in exhaust gases. At the same time, vehicles contain more and more electronic devices requiring electrical energy.

  • Small, lightweight, stretchable, cost-efficient thermoelectric devices signify a breakthrough in sustainable energy development and waste heat recovery.
  • Next-gen flexible energy harvesting systems will owe their efficiency to the integration of graphene nanotubes. They offer easy processability, stable thermoelectric performance, flexibility, and robust mechanical properties.
  • Nanocomposites have high market potential in manufacturing generators for medical and smart wearables, vehicles sensors, and efficient building management.

Around half of the world’s useful energy is wasted as heat due to the limited efficiency of energy conversion devices. For example, one-third of a vehicle’s energy dissipates as waste heat in exhaust gases. At the same time, vehicles contain more and more electronic devices requiring electrical energy. As another example, lightweight wearable sensors for health and environmental monitoring are also becoming increasingly demanding. The potential to convert waste heat or solar energy into useful electrical power has emerged as an opportunity for more sustainable energy management. Convenient thermoelectric generators (TEGs) currently have only low effectiveness and a relatively large size and weight. Based on expensive or corrosion-vulnerable materials, they are rigid and often contain toxic elements.
 
Recently developed, easy-to-process, self-supporting and flexible nonwoven nanocomposite sheets demonstrate excellent thermoelectric properties combined with good mechanical robustness. A recent paper in ACS Applied Nano Materials described how researches combined a thermoplastic polyurethane (TPU) with TUBALLTM graphene nanotubes to fabricate a nanocomposite material capable of harvesting electrical energy from sources of waste heat.

Thanks to their high aspect ratio and specific surface area, graphene nanotubes provide TPU with electrical conductivity, making it possible to achieve high thermoelectrical performance while maintaining or improving mechanical properties. “Stiffness, strength, and tensile toughness were improved by 7, 25, and 250 times compared to buckypapers, respectively. Nanocomposite sheet shows low electrical resistivity of 7.5*10-3 Ohm×cm, high Young’s modulus of 1.8 GPa, failure strength of 80 MPa, and elongation at break of 41%,” said Dr. Beate Krause, Group Leader, Leibniz-Institut für Polymerforschung Dresden e. V.

Graphene nanotubes, being a fundamentally new material, provide an opportunity to replace current TEG materials with more environmentally friendly ones. The sensors powered by such thermoelectric generators could act as a “smart skin” for vehicles and buildings, providing sensoring capabilities to monitor performance and prevent potential issues before they lead to breakdowns, ensuring optimal operational efficiency. In aircraft, no-wire nanocomposites could serve as stand-alone sensors for monitoring deicing systems, eliminating the need for an extensive network of electrical cables. The high flexibility, strength, and reliability of graphene nanotube-enabled thermoelectric materials also extend their applications into the realm of smart wearable and medical devices.

Source:

Leibniz-Institut für Polymerforschung Dresden e. V. / OCSiAl

Berndt Köll on the Stubai Glacier: Initial field tests showed convincing results. (c) Lenzing AG
22.11.2023

Glacier protection rethought: Nonwovens made of cellulosic fibers

Protection for snow and ice: Cellulosic LENZING™ fibers offer solution for preservation of glacier mass

In field trials on Austrian glaciers, nonwovens made of cellulosic LENZING™ fibers are being used to cover glacier mass. They are showing promising results and offer a sustainable solution for glacier protection. Nonwovens containing fossil-based synthetic fibers might cause negative environmental consequences such as microplastics on glaciers.

Protection for snow and ice: Cellulosic LENZING™ fibers offer solution for preservation of glacier mass

In field trials on Austrian glaciers, nonwovens made of cellulosic LENZING™ fibers are being used to cover glacier mass. They are showing promising results and offer a sustainable solution for glacier protection. Nonwovens containing fossil-based synthetic fibers might cause negative environmental consequences such as microplastics on glaciers.

Geotextiles are already widely used to protect snow and ice on glaciers from melting. The use of nonwovens made from cellulosic LENZING™ fibers is now achieving a sustainable turnaround. Geotextiles show great success in Austria in protecting glaciers, which are highly endangered by global warming. By covering glacier mass, its melting is slowed down and mitigated. So far, the nonwovens used to protect glaciers are usually made of fossil-based synthetic fibers. The problem with that might occur as microplastics left behind after the summer flow down into the valley and can enter the food chain through small organisms and animals.

Sustainability from production to reuse
An innovative and sustainable solution for the protection of snow and ice is now possible with the help of nonwovens made of cellulosic LENZING™ fibers. "LENZING™ fibers are derived from renewable, responsibly managed wood sources and are produced in an environmentally responsible process. Thanks to their botanic origin, they have the ability to break down, returning into nature after use" explains Berndt Köll, Business & Innovation Manager at Lenzing.

In a field trial on the Stubai Glacier, the covering of a small area with the new material containing cellulosic LENZING™ fibers was tested for the first time. The result was convincing: 4 meters of ice mass could be saved from melting. Due to its success, the project is now being expanded. In 2023 field tests started in all Austrian glaciers, which are used for tourism.

"We are pleased with the positive results and see the project as a sustainable solution for glacier protection - not only in Austria, but beyond national borders," Berndt Köll continues. There should also be a possibility to explore for recycling after the nonwovens are used: These geotextiles can be recycled and ultimately used to make yarn for textile products.

Awarded with the Swiss BIO TOP
The sustainable glacier protection and its results also convinced the jury of industry experts of the BIO TOP, a major award for wood and material innovations in Switzerland. With this award innovative projects in the field of bio-based woods and materials are promoted and supported. At the award ceremony on September 20, 2023, Geotextiles containing LENZING™ fibers were honored with the award for its solution.

Source:

Lenzing AG

TiHive Wins RISE® Innovation Award for their SAPMonit Technology Photo INDA
03.10.2023

TiHive Wins RISE® Innovation Award for their SAPMonit Technology

Business leaders, product developers, and technology scouts convened at the RISE® (Research, Innovation & Science for Engineered Fabrics) Conference, Sept. 26-27, Raleigh, NC for two days of valuable insights in material science, process and sustainability innovations. RISE is co-organized by INDA and The Nonwovens Institute, North Carolina State University.

Industry, academic, and government experts shared their expertise in these key areas:

Business leaders, product developers, and technology scouts convened at the RISE® (Research, Innovation & Science for Engineered Fabrics) Conference, Sept. 26-27, Raleigh, NC for two days of valuable insights in material science, process and sustainability innovations. RISE is co-organized by INDA and The Nonwovens Institute, North Carolina State University.

Industry, academic, and government experts shared their expertise in these key areas:

  • The future of nonwoven manufacturing
  • Real-world applications and advances in filter media
  • rPolymers and sustainability
  • Innovative strategies and circular solutions
  • Advancements in sustainable nonwoven applications
  • Market statistics and data trends

A highlight of RISE was a poster presentation of fundamental nonwovens research by The Nonwovens Institute’s graduate students. As an added value, The Nonwovens Institute offered RISE participants a tour of its world-class facilities located on the Centennial Campus of North Carolina State University, featuring the most extensive set of lab- and pilot-scale equipment found anywhere including all the nonwovens platform and testing technologies.

RISE® Innovation Award Winner
TiHive won the 2023 RISE Innovation Award for their SAPMonit technology. TiHive’s innovation, SAPMonit – a technology breakthrough, inspects millions of diapers weekly. SAPMonit delivers lightning-speed inline inspection of superabsorbents’ weight and distribution, optimizes resources, detects flaws, and accelerates R&D. SAPMonit utilizes advanced see-through cameras, high-speed vision algorithms, and secure cloud integration, revolutionizing industry norms. SAPMonit has great potential for sustainability, cost reduction, and enhanced customer satisfaction as it avoids hundreds of tons of plastic waste per year per machine.

The RISE Innovation Award finalists included Curt. G. Joa, Inc. for their ESC-8 – The JOA® Electronic Size Change, Fiberpartner Aps for their BicoBio Fiber, and Reifenhäuser REICOFIL GmbH & Co. KG for their Reifenhäuser Reicofil RF5 XHL.  Together, these finalists’ innovations have the potential to reduce plastic waste by millions of kgs.

DiaperRecycle won the 2022 RISE® Innovation Award for its innovative technology to recycle used diapers into absorbent and flushable cat litter. By diverting used diapers from households and institutions, and separating the plastic and fiber, DiaperRecycle strives to decrease the climate-changing emissions of diapers from landfills.

2023 INDA Lifetime Technical Achievement Award
Ed Thomas, President, Nonwoven Technology Associates, LLC, received the 2023 INDA Lifetime Technical Achievement Award for his decades of nonwoven contributions to the growth and success of the nonwoven industry.

RISE 2024 will be held October 1-2, 2024 at the James B. Hunt Jr. Library at North Carolina State University in Raleigh, NC.

More information:
INDA RISE® nonwovens
Source:

INDA

Photo Pixabay
10.01.2023

Fraunhofer: Optimized production of nonwoven masks

Producing infection control clothing requires a lot of energy and uses lots of material resources. Fraunhofer researchers have now developed a technology which helps to save materials and energy when producing nonwovens. A digital twin controls key manufacturing process parameters on the basis of mathematical modeling. As well as improving mask manufacturing, the ProQuIV solution can also be used to optimize the production parameters for other applications involving these versatile technical textiles, enabling manufacturers to respond flexibly to customer requests and changes in the market.

Producing infection control clothing requires a lot of energy and uses lots of material resources. Fraunhofer researchers have now developed a technology which helps to save materials and energy when producing nonwovens. A digital twin controls key manufacturing process parameters on the basis of mathematical modeling. As well as improving mask manufacturing, the ProQuIV solution can also be used to optimize the production parameters for other applications involving these versatile technical textiles, enabling manufacturers to respond flexibly to customer requests and changes in the market.

Nonwoven infection control masks were being used in their millions even before the COVID-19 pandemic and are regarded as simple mass-produced items. Nevertheless, the manufacturing process used to make them needs to meet strict requirements regarding precision and reliability. According to DIN (the German Institute for Standardization), the nonwoven in the mask must filter out at least 94 percent of the aerosols in the case of the FFP-2 mask and 99 percent in the case of the FFP-3 version. At the same time, the mask must let enough air through to ensure that the wearer can still breathe properly. Many manufacturers are looking for ways to optimize the manufacturing process. Furthermore, production needs to be made more flexible so that companies are able to process and deliver versatile nonwovens for a wide range of different applications and sectors.

ProQuIV, the solution developed by the Fraunhofer Institute for Industrial Mathematics ITWM in Kaiserslautern, fulfills both of these aims. The abbreviation “ProQuIV” stands for “Production and Quality Optimization of Nonwoven Infection Control Clothing” (Produktions- und Qualitätsoptimierung von Infektionsschutzkleidung aus Vliesstoffen). The basic idea is that manufacturing process parameters are characterized with regard to their impact on the uniformity of the nonwoven, and this impact is then linked to properties of the end product; for example, a protective mask. This model chain links all relevant parameters to an image analysis and creates a digital twin of the production process. The digital twin enables real-time monitoring and automatic control of nonwoven manufacturing and thus makes it possible to harness potential for optimization.

Dr. Ralf Kirsch, who works in the Flow and Material Simulation department and heads up the Filtration and Separation team, explains: “With ProQuIV, the manufacturers need less material overall, and they save energy. And the quality of the end product is guaranteed at all times.”

Nonwoven manufacturing with heat and air flow
Nonwovens for filtration applications are manufactured in what is known as the
meltblown process. This involves melting down plastics such as polypropylene and forcing them through nozzles so they come out in the form of threads referred to as filaments. The filaments are picked up on two sides by air flows which carry them forward almost at the speed of sound and swirl them around before depositing them on a collection belt. This makes the filaments even thinner: By the end of the process, their thickness is in the micrometer or even submicrometer range. They are then cooled, and binding agents are added in order to create the nonwoven. The more effectively the temperature, air speed and belt speed are coordinated with each other, the more uniform the distribution of the fibers at the end and therefore the more homogeneous the material will appear when examined under a transmitted light microscope. Lighter and darker areas can thereby be identified — this is referred to by experts as cloudiness. The Fraunhofer team has developed a method to measure a cloudiness index on the basis of image data. The light areas have a low fiber volume ratio, which means that they are less dense and have a lower filtration rate. Darker areas have a higher fiber volume and therefore a higher filtration rate. On the other hand, the higher air flow resistance in these areas means that they filter a smaller proportion of the air that is breathed in. A larger proportion of the air flows through the more open areas which have a less effective filtration effect.

Production process with real-time control
In the case of ProQuIV, the transmitted light images from the microscope are used to calibrate the models prior to use. The experts analyze the current condition of the textile sample and use this information to draw conclusions about how to optimize the system — for example, by increasing the temperature, reducing the belt speed or adjusting the strength of the air flows. “One of the key aims of our research project was to link central parameters such as filtration rate, flow resistance and cloudiness of a material with each other and to use this basis to generate a method which models all of the variables in the production process mathematically,” says Kirsch. The digital twin monitors and controls the ongoing production process in real time. If the system deviates slightly from where it should be — for example, if the temperature is too high — the settings are corrected automatically within seconds.

Fast and efficient manufacturing
“This means that it is not necessary to interrupt production, take material samples and readjust the machines. Once the models have been calibrated, the manufacturer can be confident that the nonwoven coming off the belt complies with the specifications and quality standards,” explains Kirsch. ProQuIV makes production much more efficient — there is less material waste, and the energy consumption is also reduced. Another advantage is that it allows manufacturers to develop new nonwoven-based products quickly — all they have to do is change the target specifications in the modeling and adjust the parameters. This enables production companies to respond flexibly to customer requests or market trends.

This might sound logical but can be quite complex when it comes to development. The way that the values for filtration performance and flow resistance increase, for example, is not linear at all, and they are not proportional to the fiber volume ratio either. This means that doubling the filament density does not result in double the filtration performance and flow resistance — the relationship between the parameters is much more complex than that. “This is precisely why the mathematical modeling is so important. It helps us to understand the complex relationship between the individual process parameters,” says ITWM researcher Kirsch. The researchers are able to draw on their extensive expertise in simulation and modeling for this work.

More applications are possible
The next step for the Fraunhofer team is to reduce the breathing resistance of the nonwovens for the wearer without impairing the protective effect. This is made possible by electrically charging the fibers and employing a principle similar to that of a feather duster. The electric charge causes the textile fabric to attract the tiniest of particles which could otherwise slip through the pores. For this purpose, the strength of the electrostatic charge is integrated into the modeling as a parameter.

The Fraunhofer researchers’ plans for the application of this method extend far beyond masks and air filters. Their technology is generally applicable to the production of nonwovens — for example, it can also be used in materials for the filtration of liquids. Furthermore, ProQuIV methods can be used to optimize the manufacture of nonwovens used in sound-insulating applications.

Source:

Fraunhofer Institute for Industrial Mathematics ITWM

(c) MAI Carbon
24.05.2022

From waste to secondary raw material - wetlaid nonwovens made from recycled carbon fibers

MAI Scrap SeRO | From Scrap to Secondary Ressources – Highly Orientated Wet-Laid-Nonwovens from CFRP-Waste

The »Scrap SeRO« project is an international joint project in the field of »recycling of carbon fibers«.

The technical project goal is the demonstration of a continuous process route for processing pyrolytically recycled carbon fibers (rCF) in high-performance second-life component structures. In addition to the technological level, the focus of the project is particularly on the international transfer character, in the sense of a cross-cluster initiative between the top cluster MAI Carbon (Germany) and CVC (South Korea).

MAI Scrap SeRO | From Scrap to Secondary Ressources – Highly Orientated Wet-Laid-Nonwovens from CFRP-Waste

The »Scrap SeRO« project is an international joint project in the field of »recycling of carbon fibers«.

The technical project goal is the demonstration of a continuous process route for processing pyrolytically recycled carbon fibers (rCF) in high-performance second-life component structures. In addition to the technological level, the focus of the project is particularly on the international transfer character, in the sense of a cross-cluster initiative between the top cluster MAI Carbon (Germany) and CVC (South Korea).

Through direct cooperation between market-leading companies and research institutions of the participating cluster members, the technical project processing takes place in the context of the global challenge of recycling, as well as the need for increased resource efficiency, with reference to the economically strategic material carbon fibers.

Efficient processing of recycled carbon fibers
The technological process route within the project runs along the industrial wet-laying technology, which is comparable to classic paper production. This enables a robust production of high-quality rCF nonwovens, which are characterized, among other things, by particularly high homogeneity and stability of characteristic values.

A special development focus is on a specific process control, which allows the generation of an orientation of the individual fiber filaments in the nonwoven material.

The given preferred fiber direction of the discontinuous fiber structure opens up strong synergy effects in relation to increased packing densities, i.e. fiber volume content, as well as a significantly optimized processing behavior in relation to impregnation, forming and consolidation, in addition to a load path-oriented mechanics.

The innovative wetlaid nonwovens are then further processed into thermoset and thermoplastic semi-finished products, i.e. prepregs or organosheets, using impregnation processes that are suitable for large-scale production.

rCF tapes are produced from this in an intermediate slitting step. By means of automated fiber placement, load path-optimized preforms can be deposited, which are then consolidated into complex demonstrator components.

The process chain is monitored at key interfaces by innovative non-destructive measurement technology and supplemented by extensive characterization methods. Especially for the processing of pyrolysed recycled carbon fibers, which were recovered from end-of-life waste or PrePreg waste, for example, there are completely new potentials with significant added value compared to the current state of the art for the overall process route presented here.

International Transfer
The fundamentally global challenge of recycling and the striving for increased sustainability is strongly influenced by national recycling strategies as a result of country-specific framework conditions. The globalized way in which companies deal with high-volume material flows places additional demands on a functioning circular economy. A networked solution can only be created on the basis of and in compliance with the respective guidelines and structural factors.

In the case of the high-performance material carbon fiber, there is a particularly high technical requirement for an ecologically and economically viable recycling industry. At the same time, the specific market size already opens up interesting scaling effects and potential for market penetration.

The Scrap SeRO project connects two of the world's leading top clusters in the field of carbon composites from South Korea and Germany on the basis of a cross-cluster initiative. As part of this first promising technology project, the foundation stone for future cooperation is to be laid that supports the effective recycling of carbon fibers. The project makes an important contribution to closing the material cycle for carbon fibers and thus paves the way for renewed use in further life cycles of this high-quality and energy-intensive material.

Info »Scrap SeRO«

  • Duration: 05/2019 – 04/2022
  • Funding: BMBF
  • Funding Amount: 2.557.000 €

National Consortium

  • Fraunhofer Institute for Casting, Composite and Processing Technology IGCV
  • ELG Carbon Fibre
  • J.M. Voith SE & Co. KG
  • Neenah Gessner
  • SURAGUS GmbH
  • LAMILUX Composites GmbH
  • Covestro Deutschland AG
  • BA Composites GmbH
  • SGL Carbon

International Consortium

  • KCarbon
  • Hyundai
  • Sangmyung University
  • TERA Engineering
Source:

Fraunhofer Institute for Casting, Composite and Processing Technology IGCV

(c) A3/Christian Strohmayr
10.05.2022

Fraunhofer reduces CO2 footprint and recycles trendy lightweight carbon material

Neo-ecology through innovative paper technology

To reduce the CO2 footprint, the Fraunhofer Institute for Casting, Composite and Processing Technology IGCV Augsburg research with a state-of-the-art wetlaid nonwoven machine for recycling carbon fibers. The production processes are similar to those of a paper manufacturing machine. The crucial difference: we turn not paper fibers into the paper but recycled carbon fibers into nonwoven roll fabrics. The carbon fiber thus gets a second life and finds an environmentally friendly way in nonwovens, such as door panels, engine bonnets, roof structures, underbody protection (automotive), and heat shields (helicopter tail boom), as well as in aircraft interiors.

“Wetlaid technology for processing technical fibers is currently experiencing a revolution following centuries of papermaking tradition.”
Michael Sauer, Researcher at Fraunhofer IGCV

Neo-ecology through innovative paper technology

To reduce the CO2 footprint, the Fraunhofer Institute for Casting, Composite and Processing Technology IGCV Augsburg research with a state-of-the-art wetlaid nonwoven machine for recycling carbon fibers. The production processes are similar to those of a paper manufacturing machine. The crucial difference: we turn not paper fibers into the paper but recycled carbon fibers into nonwoven roll fabrics. The carbon fiber thus gets a second life and finds an environmentally friendly way in nonwovens, such as door panels, engine bonnets, roof structures, underbody protection (automotive), and heat shields (helicopter tail boom), as well as in aircraft interiors.

“Wetlaid technology for processing technical fibers is currently experiencing a revolution following centuries of papermaking tradition.”
Michael Sauer, Researcher at Fraunhofer IGCV

The wetlaid technology used is one of the oldest nonwoven forming processes (around 140 BC - 100 AD). As an essential industry sector with diverse fields of application, wetlaid nonwovens are no longer only found in the classic paper. Instead, the application areas extend, for example, from adhesive carrier films, and packaging material, to banknotes and their process-integrated watermarks and security features. In the future, particularly sustainable technology fields will be added around battery components, fuel cell elements, filtration layers, and even function-integrated material solutions, e.g., EMI shielding function.

Fraunhofer IGCV wetlaid nonwovens line is specifically designed as a pilot line. In principle, very different fiber materials such as natural, regenerated, and synthetic fibers can be processed, mainly recycled and technical fibers. The system offers the highest possible flexibility regarding material variants and process parameters. In addition, sufficiently high productivity is ensured to allow subsequent scaled processing trials (e.g., demonstrator production).

The main operating range of the wetlaid line relates to the following parameters:

  • Processing speed: up to 30 m/min
  • Role width: 610 mm
  • Grammage: approx. 20–300 gsm
  • Overall machinery is ≥ IP65 standard for processing, e.g., conductive fiber materials
  • Machine design based on an angled wire configuration with high dewatering capacity, e.g., for processing highly diluted fiber suspensions or for material variants with high water retention capacity.
  • Machine modular system design with maximum flexibility for a quick change of material variants or a quick change of process parameters. The setup allows short-term hardware adaptations as well as project-specific modifications.

Research focus: carbon recycling at the end of the life cycle
The research focus of Fraunhofer IGCV is primarily in the field of technical staple fibers. The processing of recycled carbon fibers is a particular focus. Current research topics in this context include, for example, the research, optimization, and further development of binder systems, different fiber lengths and fiber length distributions, nonwoven homogeneity, and fiber orientation. In addition, the focus is on the integration of digital as well as AI-supported methods within the framework of online process monitoring. Further research topics, such as the production of gas diffusion layers for fuel cell components, the further development of battery elements, and filtration applications, are currently being developed.

Source:

Fraunhofer Institute for Casting, Composite and Processing Technology IGCV

(c) STFI
14.12.2021

Funding Project Raw Material Classification of Recycled Fibers

For centuries, old textiles have been used to make tear fibers and processed into new textile products. This effective recycling is one of the oldest material cycles in the world. Today, it is not only clothing that is recycled, but also high-quality technical textiles. As the products of the textile industry evolve, so do the demands on textile recycling. The basis for this is a clear assessment and classification of raw materials.

For centuries, old textiles have been used to make tear fibers and processed into new textile products. This effective recycling is one of the oldest material cycles in the world. Today, it is not only clothing that is recycled, but also high-quality technical textiles. As the products of the textile industry evolve, so do the demands on textile recycling. The basis for this is a clear assessment and classification of raw materials.

In the research project of the German Institutes of Textile and Fiber Research Denkendorf (DITF) and the Sächsisches Textilforschungsinstitut e.V. (STFI - Saxony Textile Research Institute), a methodology is being developed that will make it possible to analyze the tearing as well as the subsequent processes with regard to fiber quality. The systematic analysis should make it possible to optimize the subsequent spinning processes in such a way that the recycled content of the yarn can be increased without the yarn properties differing significantly from those of a yarn consisting of 100% good fibers. These yarns can then be processed into sustainable textile products such as clothing or composite components.

The project, which is funded by the BMWi/IGF, is scheduled to run for two years and will end on December 31, 2022. The main benefits for the participating companies are to enable them to make greater use of secondary raw materials, to open up new markets through technologies or products developed in the project, to initiate synergies and long-term cooperation, and to prepare a joint market presence.    

The project includes several steps:

  • Material selection and procurement
    Cotton fibers to be processed are obtained from used textiles (T-shirts) and waste from the cotton spinning mill. Aramid fibers are processed from used protective clothing and technical textiles.
  • Optimization of the preparation / dissolution of the textiles
    To ensure that the fibers are detached from the corresponding textiles as gently as possible and with a not too high reduction, exact settings have to be found for the tearing process, which are technologically very demanding and require a lot of experience.
  • Determination of the quality criteria for the evaluation of the fiber dissolution
    In order to define the quality criteria, the fibers coming from the tearing mill are determined by means of an MDTA-4 measuring device from Textechno GmbH & Co. KG. The criteria determined are to be used to characterize the (lowest possible) fiber shortening caused by the tearing process.
  • Determination of optimized settings in the spinning process
    In order to determine the optimum settings for producing a yarn from the recycled fibers, they are spun after the rotor spinning process. By adjusting the spinning process, the aim is to produce a yarn that has good uniformity and also appropriate firmness.
  • Production and comparison of yarns from recycled raw materials
    In order that the recycled fibers - consisting of aramid and cotton - can each be used to produce an area-measured material, the material is to be processed at industrial scale. For this purpose, the fibers are processed over a complete blowroom line with following sliver production over adapted cards. After drawing and the following roving production, yarns are produced according to the rotor or ring spinning process. The finished yarns are used to produce knitted fabrics.
  • Coordination, analysis of results and preparation of reports
    The final report is prepared by the DITF and the STFI. The results will be transferred through publications, technical information to associations and trade fair presentations. Regular meetings with the participating companies are planned.

Textination spoke with Stephan Baz, Deputy Head of the Competence Center Staple Fiber, Weaving & Simulation, Head of Staple Fiber Technology and Markus Baumann, Research Associate at the Competence Center Staple Fiber, Weaving & Simulation (both DITF) as well as Bernd Gulich, Head of Department Nonwovens/Recycling and Johannes Leis, Research Associate Focus Nonwovens/Recycling (both STFI) about the current status of the funding project.

What is the current status of the project?
We are currently in the phase of carrying out trials and the iterative optimization of several project components. As expected, several loops are necessary for the mechanical preparation itself and also for the adjustment of the spinning process with the different variants. Ultimately, after all, the project aims at coordinating the processes of mechanical preparation and spinning as processing in order to achieve optimum results. At the same time, determining the quality criteria of the fibers produced is not trivial. This also requires the further development of processes and test methods that can be implemented productively in industry and that allow the quality of the fibers produced to be assessed effectively and unaffected by residual yarns, for example. What is really remarkable is the interest and willingness of the industry to drive the project work forward. The considerable quantities of materials required for our trials were purchased from ReSales Textilhandel und -recycling GmbH, Altex Textil-Recycling GmbH & Co. KG and Gebrüder Otto GmbH & Co. KG. Furthermore, with Temafa Maschinenfabrik GmbH, Nomaco GmbH & Co. KG, Schill + Seilacher GmbH, Spinnerei Neuhof GmbH & Co. KG and Maschinenfabrik Rieter AG, many members of the project-supporting committee are actively involved in the project, from consulting to the providing of technologies. The company Textechno Herbert Stein GmbH & Co. KG has provided a testing device of the type MDTA4 for the duration of the project and supports our work with regard to the evaluation of the mechanically prepared fibers. We are of course particularly pleased about this, as it has allowed us to look at and analyze several technologies in both mechanical preparation, testing and spinning. We expect to be able to make more detailed statements at the beginning of the coming year.

Which approaches do you think are particularly promising?
With regard to technologies, we must refer to the evaluation and analysis of the trials, which are currently still ongoing. We will be able to go into more detail in the first quarter of next year.

Of course, things are already emerging. With meta-aramid waste, promising approaches could be found very quickly; with post-consumer cotton, this is considerably more complex. Obviously, there is a link between the quality of the raw material and the quality of the products. In some cases, we have already been able to determine very low average fiber lengths in the procured goods; to a certain extent, these are of course directly reflected in the output of our processes. From this, and this is not a new finding, a great importance of the design of the textiles is again derived.

What are the challenges?
In addition to the expected high short fiber content, the residual yarns after the tearing process are an issue of particular focus. The proportion of these residual yarns can vary between the materials and preparation technologies, but the further dissolution of the products of the tearing process is essential.

If the processes are considered further in a utilization phase, the question of design naturally also arises for the best possible use of recycled fibers. Many problems, but also the approaches to solutions for the use of comparatively short fibers, can also be expected to apply to the (multiple) use of mechanically recycled fibers.

Can we speak of upcycling in the final product?
We see yarn-to-yarn recycling neither as upcycling nor downcycling, but as closed-loop recycling. The background is that the products are to go into the same application from which they came and have to compete with primary material. This means that certain specific requirements have to be met and at the same time there is considerable price pressure. In the case of downcycling, a significant reduction in properties is accepted, while in the case of upcycling, the higher-priced application can make up for the reprocessing effort. In the attempt to produce yarn material again from yarn material, both are only permissible to a small extent. This represents the particular challenge.

What does a recyclate prepared from used textiles mean for the spinning process?
Part of this question is to be answered in the project by the detailed classification of the processed fibers and is thus the subject of the tests currently underway. It turns out that, in addition to the rather obvious points such as significantly reduced fiber length, process disturbances due to undissolved fabrics and yarn pieces, there are also less obvious aspects to be considered, such as a significantly increased outgoing quantity for processing in the spinning process. The outgoing quantity is of particular interest here, because in the end the newly produced yarn should also contain a considerable proportion of prepared fibers.

What consequences does this have for textile machinery manufacturing?
The consequences that can already be estimated at the present time are that, particularly in the processing of cotton, the machinery in the spinning preparatory mill is specialized in the processing of (new) natural fibers with a certain amount of dirt. In contrast to new fibers, processed fibers are clean fibers with a significantly higher proportion of short fibers. Elements that are good at removing dirt also reject an increased amount of short fibers, which can lead to unintentionally high waste quantities under certain circumstances. It is therefore necessary to adapt the established machine technology to the new requirement profile of the raw material "processed fibers". Analogous adaptations are probably necessary along the entire processing chain up to the yarn. In the drafting system of the spinning machine, of course, this is due more to the high short fiber ratio than to elements that have been optimized for cleaning out dirt and foreign substances.

Source:

Textination GmbH

Foto: Pixabay
09.11.2021

NGST - Next Generation Protective Textiles

  • Efficient Production of Novel, High-Quality Infection-Protective Textiles

 
Considerable shortages of protective textiles, especially respirators, occurred during the SARS-CoV-2 pandemic, which were exacerbated by the lack of sufficient production capacity in Germany and the EU at the time. Short-term retooling at EU companies as well as importing goods often did not lead to success, as these protective textiles were of highly variable quality, which had a negative impact on safety.

The "Next Generation Protective Textiles" initiative aims to remedy this situation by researching new approaches for the production of high-quality protective textiles.

The "NGST" project is divided into several subtasks
The project includes:

  • Efficient Production of Novel, High-Quality Infection-Protective Textiles

 
Considerable shortages of protective textiles, especially respirators, occurred during the SARS-CoV-2 pandemic, which were exacerbated by the lack of sufficient production capacity in Germany and the EU at the time. Short-term retooling at EU companies as well as importing goods often did not lead to success, as these protective textiles were of highly variable quality, which had a negative impact on safety.

The "Next Generation Protective Textiles" initiative aims to remedy this situation by researching new approaches for the production of high-quality protective textiles.

The "NGST" project is divided into several subtasks
The project includes:

  • qualified selection of basic materials
  • studies on up-scaling to create the conditions for a rapid expansion of production capacities
  • development of novel antiviral coatings
  • comprehensive biological and material science analysis to verify the improved properties and also to open up new methods of quality control.

The protective textiles to be developed in the project have a wide range of applications beyond use in the medical field and in civil protection. In principle, wherever immediate cleaning and disinfection are difficult or special filtration tasks are necessary, such as in mobile or stationary filter systems for air purification or for individual personal protection.

In this project, the Fraunhofer IGCV is researching the development of a manufacturing process for nonwovens as a basis for infection protection and filtration media based on wet nonwoven technology. Compared to the state of the art (meltblown technology), this is potentially characterised by significantly increased production capacities as well as increased flexibility with regard to material variety. The main challenges here are the very high quality requirements based on low basis weights for processing the finest possible micro-staple fibres..
          
Pursuing novel approaches to increase quality and productivity in the production of protective textiles
The aim is to provide optimised nonwoven materials as a starting material for subsequent antiviral coatings, and to assess and demonstrate the high technological potential of wet nonwoven technology in this field of application.

For this purpose, an existing pilot wetlaid nonwoven line was specifically modified on a pilot plant scale. This makes it possible to produce nonwoven materials from micro-staple fibres in the required very high quality in terms of uniformity, basis weight, blending and thickness profile with high reproducibility. A standard PP nonwoven was used as a comparison system, which was produced according to the current state of the art using meltblown technology. In addition to the PP comparison variants, however, the processing of PLA, viscose and PET staple fibres, among others, was also investigated. The focus here is on maximum fibre fineness (microfibres) in each case in order to achieve the largest possible specific fibre surface or effective area in the nonwoven. In order to emphasise the significantly increased flexibility of wetlaid technology, particularly innovative variants based on modified bi-component fibres with maximised fibre surface area as well as split fibres are also being conceptually tested.

In addition to aspects of direct material and process development, the scale of the pilot plant provides a comprehensive data basis for estimating a later scaling up to an industrial series. This should create a technological starting point for the ramp-up of an efficient, national production of fleece-based infection control materials based on wet-laying technology.

Source:

Fraunhofer Institute for Casting, Composite and Processing Technology IGCV

Photo: pixabay
19.10.2021

Micromechanical Simulation of the Resilience of Nonwovens

Nonwovens are an important component of different products of several uses, e.g. transport of humidity in sanitary products, insulation materials or filters. Nonwovens are usually produced on large engineering facilities. For this, experimental studies of design with regard to the optimization of these nonwoven-structures prove to be very difficult.

Influence Design Parameters
There are so many parameters of design, as for example fibers, surface weight or type of nonwoven bonding and finishing that are affecting the properties of nonwovens. For the change of one single parameter, e.g. the material of fiber, it is necessary to adapt the whole process of fabrication from the spinning of the fibers via their stacking to the nonwoven hardening.

Nonwovens are an important component of different products of several uses, e.g. transport of humidity in sanitary products, insulation materials or filters. Nonwovens are usually produced on large engineering facilities. For this, experimental studies of design with regard to the optimization of these nonwoven-structures prove to be very difficult.

Influence Design Parameters
There are so many parameters of design, as for example fibers, surface weight or type of nonwoven bonding and finishing that are affecting the properties of nonwovens. For the change of one single parameter, e.g. the material of fiber, it is necessary to adapt the whole process of fabrication from the spinning of the fibers via their stacking to the nonwoven hardening.

Following the production of such a prototype a time consuming and cost-intensive characterization of the properties of nonwovens carried out experimentally has to be done.  Therefore, for this reason detailed studies considering several parameters of design are uneconomic.

Thus, micromechanical models of simulation are developed at Fraunhofer ITWM in cooperation with Procter & Gamble Service GmbH (P & G). By means of these models it is possible to forecast numerically the effective properties of nonwovens for diverse parameters of design. To virtually modify and optimize individual parameters in this connection it is only necessary to adapt the corresponding inputs of the model.

Fast Predictions Possible
In this case, the focus of the numerical predictions is primarily lying on the time-dependent behavior of the nonwovens.  The dynamic properties can be determined by means of numerical simulation of cyclic measurements. In doing so, a good correspondence of simulation and measurements is obtained.

Compared to experiments the required time of simulation for the behavior in case of low frequencies does not change. Therefore, we can obtain rapid forecasts for the long-term behavior (month till years) and the corresponding resilience of nonwovens using numerical models. A lot of alternatives can be simulated and studied within a few hours.

The fact that not only effective (macroscopic) properties of nonwovens can be computed, but also local physical values such as distribution of tension in binding agents and fibres is a further advantage of this micromechanical  approach. So, the simulation contributes to a better understanding of the properties of nonwovens.

Future designs deal with an extension of the models with regard to simulation of the productionv processes. By this, a fully digitalized layout design of nonwovens, from the manufacturing process till the optimization of functionality is possible.

Source:

Fraunhofer Institute for Industrial Mathematics ITWM

Photo: pixabay
21.09.2021

Virtual Quality Inspection Optimizes Production of Filter Nonwovens

Nonwoven production received more attention than ever before from the general public in Corona times, because the technical textile is crucial for infection protection. The ultra-fine nonwoven products are manufactured in so-called meltblown processes. A cross-departmental team at the Fraunhofer Institute for Industrial Mathematics ITWM in Kaiserslautern is optimizing the entire production chain in the »ProQuIV« project. Simulations help to guarantee the product quality of the filter material despite fluctuations in production.

Nonwoven production received more attention than ever before from the general public in Corona times, because the technical textile is crucial for infection protection. The ultra-fine nonwoven products are manufactured in so-called meltblown processes. A cross-departmental team at the Fraunhofer Institute for Industrial Mathematics ITWM in Kaiserslautern is optimizing the entire production chain in the »ProQuIV« project. Simulations help to guarantee the product quality of the filter material despite fluctuations in production.

The abbreviation »ProQuIV« stands for »Production and Quality Optimization of Nonwoven Infection Protection Clothing«. This is because bottlenecks in the production of these materials were particularly evident at the beginning of the Covid 19 crisis. For the meltblown nonwovens, this optimization of the product quality is also particularly difficult because the textiles react very sensitively to fluctuations in the manufacturing processes and material impurities.

Digital Twin Keeps an Eye on the Big Picture
»Meltblown« is the name of the industrial manufacturing process whose ultra-fine fiber nonwovens are responsible for providing the crucial filtering function in face masks. In this process, the molten polymer is forced through nozzles into a forward-flowing, high-speed stream. It is stretched and cooled in a highly turbulent air flow.

»The overall process of filter media production – from the polymer melt to the filter medium – presents a major challenge in simulation,« explains Dr. Konrad Steiner, head of the »Flow and Materials Simulation« department. »In the project, we kept the big picture in mind and developed a completely integrated evaluation chain as a digital twin. In doing so, we take several key components into account at once: We simulate the typical production processes of nonwovens, the formation of the fiber structures and then the material properties – here, in particular, the filter efficiency. This allows us to quantitatively evaluate the influences of the manufacturing process on the product properties.« In each of these individual areas, Fraunhofer ITWM and its experts are among the leading research groups internationally.

Homogeneity of the Material – Fewer Clouds in the Simulation Sky
In the meltblown process, a key factor is the behavior of the filaments in the turbulent, hot and fast air flow. The properties of the filaments are strongly influenced by this air flow. The quality of the filaments – and thus the quality of the nonwovens – is influenced by many factors. Dr. Dietmar Hietel, head of the »Transport Processes« department, knows what this means more precisely in practice. His team has been working at Fraunhofer ITWM for years on the simulation of various processes involving filaments, threads, and fibers. »The focus of the project is the so-called cloudiness, i.e. the non-uniformity of the fiber distributions in the nonwoven,« explains Hietel. »We are investigating the question: How homogeneous is the fabric? Because the quality of the products can be greatly improved if we increase the uniformity. Our simulations help figure out how to do that.«

Objective Evaluation of the Homogeneity of Nonwovens
The researchers also use appropriate image analysis techniques to quantify this cloudiness. The power spectrum plays a special role here. »The cloudiness index (CLI) describes homogeneity complementary to local basis weight and its variance,« describes Dr. Katja Schladitz. She brings her expertise in image processing to the project. »Our CLI ensures a robust assessment of the homogeneity and can thus be used for different material classes and imaging techniques to be used as an objective measure.« The frequencies that go into the CLI calculation can be chosen so that the CLI is meaningful for the particular application area.

Filtration: How Efficient Are the Filters?
For the upscaling to industrial processes such as mask production, the ITWM expertise in filters is also included in the project. The »Filtration and Separation« team led by Dr. Ralf Kirsch has been working for years on the mathematical modeling and simulation of various separation processes.

»What's special about this project is that we calculated the efficiency of the filters for fluctuations of varying degrees in the fiber volume fraction,« emphasizes Kirsch. »This allows us to specify up to what level of cloudiness the required filter efficiency can be achieved at all.« As a current example of this, the figure depicts in the graphic the efficiency of a filter material for N95 masks as a function of the inhomogeneity of the nonwoven.

ITMW Methods Support Across the Entire Process Chain
In »ProQuIV«, digital twins and calculations from Fraunhofer ITWM support a holistic view and better understanding of the processes. The production of technical textiles thus not only becomes more efficient, but the nonwovens can be developed virtually without having to realize this in advance in a test facility. In this way, production capacities can be increased while maintaining or even increase the quality. Together with long-term partners from industry, the research can be put into practice quickly and efficiently.

Simulations save textile companies experiments, allow new insights, enable systematic parameter variations and solve upscaling problems that can otherwise lead to bad investments during the transition from laboratory plant to industrial plant. However, virtual implementation of nonwoven production also opens up new opportunities for optimization at other levels. For example, acoustic insulating nonwovens or even hygiene nonwovens can also be optimized in terms of their product quality precisely with regard to the material properties to be achieved – while taking into account the process fluctuations that occur.

The project is part of the Fraunhofer-Gesellschaft's »Fraunhofer versus Corona« program and was completed in April 2021. The results will flow into several follow-up projects with the nonwovens industry.

Photo: pixabay
24.08.2021

Air, Water, Oil: What PLA bioplastic can filter well - and what not

Air filters have been discussed so often in recent days in the fight against the pandemic. With filter material made of nonwoven fabric, they block the way back into rooms for aerosols containing viruses. But how can these devices not only protect health, but also be operated with filter material that is as environmentally friendly as possible?

Air filters have been discussed so often in recent days in the fight against the pandemic. With filter material made of nonwoven fabric, they block the way back into rooms for aerosols containing viruses. But how can these devices not only protect health, but also be operated with filter material that is as environmentally friendly as possible?

Under clearly defined conditions, the bioplastic polylactide (PLA), also known as polylactic acid, is suited for this purpose. This can be deduced from results obtained by researchers from the Zuse community in the recently completed "BioFilter" research project. The key question for this and other potential applications of biofilters is: How do the special properties of PLA affect the filter performance and durability? After all, PLA can have practical disadvantages compared to its fossil-based competitors. Its material tends to be brittle and it doesn't particularly like high temperatures beyond 60 degrees Celsius. As a biogenic material, polylactic acid is also potentially more susceptible to abrasion and organic degradation processes. This can play an even greater role in the use of filters, e.g. in sewage treatment facilities, than in air filters. Industrial customers, however, naturally want a durable, reliable product.

From monofilament to nonwoven
Against this background, the researchers studied the PLA properties in order to test nonwovens for biofilters on this basis. The German Textile Research Center North-West (German Textile Research Center North-West - DTNW) and the Saxon Textile Research Institute (STFI), where the nonwovens were produced, were involved. Granules from various commercially available manufacturers were used. However, the research did not start with nonwovens, in which the fibers are deposited close together in different layers, but with so-called monofilaments, i.e. fibers made of PLA that are comparable to threads. DTNW and STFI initially carried out tests on these monofilaments, e.g. in a climate chamber for aging and durability.

As can be seen in the picture, the monofilaments became brittle after only two weeks at higher temperatures from 70 degrees Celsius, as the DTNW authors recently reported in the Journal Applied Polymer Materials. Under normalized conditions, however, the monofilaments showed no measurable reduction in stability even after almost three years, and the PLA nonwovens were in no way inferior to their fossil-based counterparts in terms of filter performance. "In my opinion, the focus for the use of PLA as a filter material will be on applications where relatively low temperatures are present, with which PLA copes very well," says DTNW scientist Christina Schippers.

Besides temperature and humidity consider other factors
For the researchers, however, the project, which was funded by the German Federal Ministry for Economic Affairs and Energy, was not just about the suitability of polylactide for air filters, but also for other applications, such as filtering water. In addition, the research revealed that when evaluating filter media made from bio-based and biodegradable nonwovens, it is important to consider other influencing factors, such as mechanical loads caused by air currents, in addition to temperature and humidity. "The innovative core of the project was to evaluate the possibilities and application limits of PLA nonwovens as filter media with sufficient mechanical properties and long-term stability," says project leader Dr. Larisa Tsarkova. Like her colleagues at STFI, DTNW is involved in the Zuse Community's Bioeconomy Cluster, in which researchers from nonprofit institutes cooperate under the guiding principle of "Researching with Nature." "For us, the bioeconomy is a top cross-industry topic that connects numerous institutes of the Zuse Community and is lived through collaborations such as with the 'Bio-Filter'," explains the future STFI managing director Dr. Heike Illing-Günther.

Cooperation in the Bioeconomy Cluster
With the results obtained from the "Bio-Filter" project, DTNW and STFI now want to continue working in order to be able to make derivations for clearly described areas of application for PLA nonwoven filters in the future. These possible fields of application extend far beyond room air filters and thus beyond the pandemic. For example, the water-repellent property of PLA is potentially interesting for filters in large-scale kitchens for water-oil filtration or also in the industry for engine oils.

The research is also so important, because PLA is already quite well established in individual consumer-related segments - keyword: carrier bags. Traditionally, lactic acid was used to preserve food, for example in sauerkraut. Today, PLA is obtained via a multi-stage synthesis from sugar, which ferments to lactic acid and polymerizes this to PLA, as Kunststoffe.de explains. PLA is one of the best-known bioplastics, but has not always been readily available due to strong demand in recent years. The Netherlands-based company Total Corbion has announced plans to start up a PLA plant with an annual capacity of 100,000 tons in Grandpuits, France, by 2024. It would be the largest plant of its kind in Europe, with Asia leading the way so far.

Source:

Deutsche Industrieforschungsgemeinschaft Konrad Zuse e.V.

Photo: pixabay
17.08.2021

Innovative wound care: Customized wound dressings made from tropoelastin

Customized, biomedically applicable materials based on tropoelastin are being developed in a joint project by Skinomics GmbH from Halle, Martin Luther University Halle-Wittenberg and the Fraunhofer Institute for Microstructure of Materials and Systems IMWS. The material combines biocompatibility, durability, biodegradability and favorable mechanical properties similar to those of skin. Preclinical tests have confirmed that it is suitable for use as a wound dressing material used in the treatment of chronic and complex wounds.

Customized, biomedically applicable materials based on tropoelastin are being developed in a joint project by Skinomics GmbH from Halle, Martin Luther University Halle-Wittenberg and the Fraunhofer Institute for Microstructure of Materials and Systems IMWS. The material combines biocompatibility, durability, biodegradability and favorable mechanical properties similar to those of skin. Preclinical tests have confirmed that it is suitable for use as a wound dressing material used in the treatment of chronic and complex wounds.

Particularly in the context of an aging society, special wound dressings are gaining in importance. The treatment of complex wound diseases such as venous ulcers, leg ulcers, or foot ulcers is challenging for medical staff, long-term and painful for those affected and cost-intensive for the healthcare system. Innovative protein-based materials are now being used for the treatment of such wounds. However, since they are made from animal tissues, they carry increased risks of infection or can result in undesirable immune reactions. In addition, there are increasing reservations in the population about medical products of animal origin.

In the joint research project, the project partners are currently developing customized, biomedically applicable materials based on human tropoelastin. This precursor protein is converted in the body to elastin, a vital and long-lived structural biopolymer that has exceptional mechanical properties and thus gives the skin and other organs the elasticity and resilience they need to function.

“Elastin is chemically and enzymatically extremely stable, biocompatible and does not produce immunological rejections when used as a biomaterial in humans. Therefore, we want to create new and innovative solutions for the treatment of complex wounds based on human tropoelastin,” says Dr. Christian Schmelzer, Head of the Department of Biological and Macromolecular Materials at Fraunhofer IMWS.

Individual wound treatment
As part of the research project led by Prof. Dr. Markus Pietzsch of Martin Luther University Halle-Wittenberg, the researchers succeeded in developing a biotechnological process for modifying tropoelastin. The modified tropoelastin is processed at Fraunhofer IMWS. Here, an electrospinning procedure is used to produce ultra-thin nanofibers with diameters of only a few hundred nanometers. The resulting nonwovens are further crosslinked to stabilize them for the respective application. The procedures developed have been optimized so that biomedical parameters such as pore size, stability and mechanical properties are variable and can thus be customized to meet the requirements of the respective wound treatment. The materials produced using the new procedures are being investigated by Skinomics GmbH in initial preclinical tests with regard to their skin compatibility and have already achieved promising results.

At the end of the project by the end of this year, applications for intellectual property rights are to be filed, building the basis for a subsequent product development phase for certified medical products.

Photo: pixabay
20.07.2021

Closed-Loop Recycling Pilot Project for Single Use Face Masks

  • Circular economy for plastics: Fraunhofer, SABIC, and Procter & Gamble join forces

The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics. The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

The transformation from a linear to a circular plastics economy can only succeed with a multi-stakeholder approach. The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE combines the competencies of six institutes of the Fraunhofer-Gesellschaft and cooperates closely with partners from industry. Together, we work on systemic, technical and social innovations and keep an eye on the entire life cycle of plastic products.  

  • Circular economy for plastics: Fraunhofer, SABIC, and Procter & Gamble join forces

The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics. The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

The transformation from a linear to a circular plastics economy can only succeed with a multi-stakeholder approach. The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE combines the competencies of six institutes of the Fraunhofer-Gesellschaft and cooperates closely with partners from industry. Together, we work on systemic, technical and social innovations and keep an eye on the entire life cycle of plastic products.  

Fraunhofer Institute for Environmental, Safety and Energy Technology UMSICHT is a pioneer in sustainable energy and raw materials management by supplying and transferring scientific results into companies, society and politics. Together with partners, the dedicated UMSICHT team researches and develops sustainable products, processes and services which inspire.

Fraunhofer Institute UMSICHT, SABIC and Procter & Gamble (P&G) are collaborating in an innovative circular economy pilot project which aimed to demonstrate the feasibility of closed-loop recycling of single-use facemasks.

Due to COVID-19, use of billions of disposable facemasks is raising environmental concerns especially when they are thoughtlessly discarded in public spaces, including - parks, open-air venues and beaches. Apart from the challenge of dealing with such huge volumes of essential personal healthcare items in a sustainable way, simply throwing the used masks away for disposal on landfill sites or in incineration plants represents a loss of valuable feedstock for new material.

“Recognizing the challenge, we set out to explore how used facemasks could potentially be returned into the value chain of new facemask production,” says Dr. Peter Dziezok, Director R&D Open Innovation at P&G. “But creating a true circular solution from both a sustainable and an economically feasible perspective takes partners. Therefore, we teamed up with Fraunhofer CCPE and Fraunhofer UMSICHT’s expert scientists and SABIC’s T&I specialists to investigate potential solutions.”

As part of the pilot, P&G collected used facemasks worn by employees or given to visitors at its manufacturing and research sites in Germany. Although those masks are always disposed of responsibly, there was no ideal route in place to recycle them efficiently. To help demonstrate a potential step change in this scenario, special collection bins were set up, and the collected used masks were sent to Fraunhofer for further processing in a dedicated research pyrolysis plant.

“A single-use medical product such as a face mask has high hygiene requirements, both in terms of disposal and production. Mechanical recycling, would have not done the job” explains Dr. Alexander Hofmann, Head of Department Recycling Management at Fraunhofer UMSICHT. “In our solution, therefore, the masks were first automatically shredded and then thermochemically converted to pyrolysis oil.

Pyrolysis breaks the plastic down into molecular fragments under pressure and heat, which will also destroy any residual pollutants or pathogens, such as the Coronavirus. In this way it is possible to produce feedstock for new plastics in virgin quality that can also meet the requirements for medical products” adds Hofmann, who is also Head of Research Department “Advanced Recycling” at Fraunhofer CCPE.

The pyrolysis oil was then sent to SABIC to be used as feedstock for the production of new PP resin. The resins were produced using the widely recognized principle of mass balance to combine the alternative feedstock with fossil-based feedstock in the production process. Mass balance is considered a crucial bridge between today’s linear economy and the more sustainable circular economy of the future.

“The high-quality circular PP polymer obtained in this pilot clearly demonstrates that closed-loop recycling is achievable through active collaboration of players from across the value chain,” emphasizes Mark Vester, Global Circular Economy Leader at SABIC. “The circular material is part of our TRUCIRCLE™ portfolio, aimed at preventing valuable used plastic from becoming waste and at mitigating the depletion of fossil resources.”

Finally, to close the loop, the PP polymer was supplied to P&G, where it was processed into non-woven fibers material. “This pilot project has helped us to assess if the close loop approach could work for hygienic and medical grade plastics.” says Hansjörg Reick, P&G Senior Director Open Innovation. “Of course, further work is needed but the results so far have been very encouraging”.

The entire closed loop pilot project from facemask collection to production was developed and implemented within only seven months. The transferability of advanced recycling to other feedstocks and chemical products is being further researched at Fraunhofer CCPE.

Photo: Pixabay
16.02.2021

Carbon with Multiple Lives: Bringing Innovations in Carbon Fiber Recycling to Market

When it comes to the future of motorized mobility, everyone talks about the power drive: How much e-car, how much combustion engine can the environment tolerate and how much do people need? At the same time, new powertrains place ineased demands not only on the engine, but also on its housing and the car body: Carbon fibers are often used for such demanding applications. Like the powertrain of the future, the materials on the vehicle should also be environmentally friendly. That is why recycling of carbon fibers is required. Institutes of the Zuse Community have developed solutions for this.

Carbon fibers consist almost completely of pure carbon. It is extracted from the plastic polyacrylonitrile at 1,300 degrees Celsius, using a lot of energy. The advantages of carbon fibers: They have almost no dead weight, are enormously break-resistant and sturdy. These properties are needed, for example, in the battery box of electric vehicles in structural components of a car body.

When it comes to the future of motorized mobility, everyone talks about the power drive: How much e-car, how much combustion engine can the environment tolerate and how much do people need? At the same time, new powertrains place ineased demands not only on the engine, but also on its housing and the car body: Carbon fibers are often used for such demanding applications. Like the powertrain of the future, the materials on the vehicle should also be environmentally friendly. That is why recycling of carbon fibers is required. Institutes of the Zuse Community have developed solutions for this.

Carbon fibers consist almost completely of pure carbon. It is extracted from the plastic polyacrylonitrile at 1,300 degrees Celsius, using a lot of energy. The advantages of carbon fibers: They have almost no dead weight, are enormously break-resistant and sturdy. These properties are needed, for example, in the battery box of electric vehicles in structural components of a car body.

The Saxon Textile Research Institute (STFI), for instance, is currently working with industrial partners on combining the static-mechanical strengths of carbon fibers with vibration damping properties to improve the housings of electric motors in cars. The project, which is funded by the German Federal Ministry for Economic Affairs and Energy, is aimed at developing hybrid nonwovens that contain other fibers, in addition to carbon fiber, as a reinforcement. "We want to combine the advantages of different fiber materials and thereby develop a product that is optimally tailored to the requirements", explains Marcel Hofmann, head of department of Textile Lightweight Construction at STFI.

The Chemnitz researchers would therefore complement previous nonwoven solutions. They look back on 15 years of working with recycled carbon fibers. The global annual demand for the high-value fibers has almost quadrupled in the past decade, according to the AVK Industry Association to around 142,000 t most recently. "Increasing demand has brought recycling more and more into focus", says Hofmann. According to him, carbon fiber waste is available for about one-tenth to one-fifth of the price of primary fibers, but they still need to be processed. The key issue for the research success of recycled fibers is competitive applications. STFI has found these not only in cars, but also in the sports and leisure sector as well as in medical technology, for example in components for computer tomography. "While metals or glass fibers cast shadows as potential competing products, carbon does not interfere with the image display and can fully exploit its advantages", explains Hofmann.
 
Using Paper Know-How
If recycled carbon fibers can pass through the product cycle again, this significantly improves their carbon footprint. At the same time it applies: The shorter the carbon fibers, the less attractive they are for further recycling. With this in mind, the Cetex Research Institute and the Papiertechnische Stiftung (PTS), both members of the Zuse Community, developed a new process as part of a research project that gives recycled carbon fibers, which previously seemed unsuitable, a second product life. "While classic textile processes use dry processing for the already very brittle recycled carbon fibers in fiber lengths of at least 80 mm, we dealt with a process from the paper industry that processes the materials wet. At the end of the process, in very simplified terms, we obtained a laminar mat made of recycled carbon fibers and chemical fibers", says Cetex project engineer Johannes Tietze, explaining the process by which even 40 mm short carbon fibers can be recycled into appealing intermediates.

The resulting product created in a hot pressing process serves as the base material for heavy-duty structural components. In addition, the mechanical properties of the semi-finished products were improved by combining them with continuous fiber-reinforced tapes. The researchers expect the recycled product to compete with glass-fiber-reinforced plastics, for example in applications in rail and vehicle construction. The results are now being incorporated into further research and development in
the cooperation network of Ressourcetex, a funded association with 18 partners from industry and science.

Successful Implementation in the Automotive Industry
Industrial solutions for the recycling of carbon fiber production waste are being developed at the Thuringian Institute of Textile and Plastics Research (TITK). Several of these developments were industrially implemented with partners at the company SGL Composites in Wackersdorf, Germany. The processing of the so-called dry waste, mainly from production, is carried out in a separate procedure. "Here, we add the opened fibers to various processes for nonwoven production", says the responsible head of the department at TITK, Dr. Renate Lützkendorf . In addition to developments for applications e.g. in the BMW i3 in the roof or rear seat shell, special nonwovens and processes for the production of Sheet Molding Compounds (SMC) were established at TITK. These are thermoset materials consisting of reaction resins and reinforcing fibers, which are used to press fiber-plastic composites. This was used, for example, in a component for the C-pillar of the BMW 7 Series. "In its projects, TITK is primarily focusing on the development of more efficient processes and combined procedures to give carbon fiber recycling materials better opportunities in lightweight construction applications, also in terms of costs", says Lützkendorf. The focus is currently on the use of CF recycled fibers in thermoplastic processes for sheet and profile extrusion. "The goal is to combine short- and continuous-fiber reinforcement in a single, high-performance process step."

1) Since February 1st, 2021, Dr.-Ing. Thomas Reussmann succeeds Dr.-Ing. Renate Lützkendorf, who retired 31 January.

Source:

Zuse Community

Graphic: Pixabay
12.01.2021

East German Textile and Clothing Industry recorded a significant Drop in Sales in 2020

  • vti calls on health textiles purchasers to place more orders with domestic manufacturers
  • East German textile and clothing industry faces the Covid-19 crises with new ideas and products
  • Clothing sector more affected than the textile sector

The Association of the North-East German Textile and Clothing Industry (vti) calls on decision-makers in politics and authorities as well as in clinics and long-term care to order far more health protection textiles from local manufacturers than before. "That would be a logical step towards future-oriented, sustainable business - and furthermore in an exceptionally tough crisis situation. We are happy to arrange appropriate contacts with our companies," emphasized Dr.-Ing. Jenz Otto, Managing Director of the Chemnitz-based industry association, during an online press conference on January 8, 2021.

  • vti calls on health textiles purchasers to place more orders with domestic manufacturers
  • East German textile and clothing industry faces the Covid-19 crises with new ideas and products
  • Clothing sector more affected than the textile sector

The Association of the North-East German Textile and Clothing Industry (vti) calls on decision-makers in politics and authorities as well as in clinics and long-term care to order far more health protection textiles from local manufacturers than before. "That would be a logical step towards future-oriented, sustainable business - and furthermore in an exceptionally tough crisis situation. We are happy to arrange appropriate contacts with our companies," emphasized Dr.-Ing. Jenz Otto, Managing Director of the Chemnitz-based industry association, during an online press conference on January 8, 2021. “We don't understand the buying resistance concerning health textiles, even though the demand is huge. It is just as incomprehensible why there are still no noteworthy orders from authorities. In spring, the German federal government had already announced to provide 1 billion Euro with its economic stimulus package for national epidemic reserves for personal protective equipment. The federal states also had to take action in this regard and stock up. We urgently await the long-announced tenders for equipping the pandemic reserve stock. It is important that the purchase price is not the only measure of all things. Rather, criteria such as standard-compliant quality, traceable supply chains, the possibility of needs-based reorders and the multiple use of textiles are decisive for the safety of the population.”

When supply chains worldwide collapsed at the beginning of 2020, both authorities and many care and health facilities turned to textile companies for help. Many manufacturers launched both everyday masks and protective textiles that could be used in healthcare at short notice.
"These include highly effective bacteria and virus-repellent reusable products that enable effective textile management in the healthcare sector and at the same time prevent the piles of single-use waste from growing there," explained vti chairman Thomas Lindner, managing director of Strumpfwerk Lindner GmbH, Hohenstein-Ernstthal: “When the cheap imports from Asia reinstated, however, the interest decreased significantly. Nevertheless, numerous companies have continued to invest in new technology and aligned their production accordingly. For example, completely new production lines of face masks have been set up at several locations. Do not forget: The very expensive test procedures for medical and health textiles are a major challenge for us, the medium-sized businesses. In addition, there are still too few accredited test and certification bodies in Germany.” The fact that the companies were able to adapt to the new requirements at this rapid pace was primarily possible, because around 30 local companies and research institutes have been part of the health textiles network "health.textil", which is controlled by the vti and supported by the Free State of Saxony, for several years now. This alliance cooperates closely with practice partners such as the University Clinic of Dresden and the Elbland Clinics in Meißen. Nowadays it has expanded their activities to their neighbouring industry, research and application partner in Czech Republic. www.healthtextil.de

CO2 taxation puts medium-sized companies at a competitive disadvantage
Concerning the permanently relevant topic energy transition in Germany, vti General Manager Dr.-Ing. Jenz Otto points out that the economic framework conditions for medium-sized producers will continue to worsen with the introduction of the CO2 taxation in the midst of the current crisis. “The financial resources to be used for this will then be lacking for investments in innovative products and environmentally friendly manufacturing processes. Furthermore, our companies suffer significant competitive disadvantages compared to foreign competitors.” Björn-Olaf Dröge, managing director of the textile finishing company pro4tex GmbH, Niederfrohna, with around 100 employees, reported that the tax to be paid by his company for renewable energies adds up to around a quarter of a million euros annually. “Now the CO2 taxation for our natural gas consumption comes on top of that. For 2021 we anticipate an additional burden of almost 70,000 Euros.”

vti about the current situation in the East German industry
The East German textile and clothing industry recorded a significant loss in sales already in 2019. This trend has continued in 2020 being reinforced by the Covid-19 crises. Based on preliminary estimates, the vti assumes that the total turnover of the industry will be more than 11 percent below the previous year at the end of 2020, where the clothing sector is affected far more than the textile sector, with a decline of 35 percent. Exports, which are extremely important for the industry, also decreased in a similar magnitude. The job cuts have so far been relatively moderate, as many companies use the short-time working regulations and try to retain their permanent workforce. For 2021 the vti sees a gleam of hope in technical textiles, which have been in greater demand again in recent weeks - especially from the automotive industry. The employment cuts have so far been relatively moderate, as many companies use short-time working regulations and try to retain their permanent workforce. The vti sees a bright future for technical textiles in 2021, which have been in greater demand – especially in the automobile industry – in the last few weeks.

Of the around 16,000 employees, 12,000 work in Saxony and 2,500 in Thuringia. This makes this region one of the four largest German textile locations, along North Rhine-Westphalia, Baden-Württemberg and Bavaria. It has modern spinning mills, weaving mills, knitting mills, warp knitting mills, nonwovens manufacturers, embroidery mills, finishing companies and clothing manufacturers as well as efficient research and educational institutions. 

Over half of the turnover in the East German textile and clothing industry has so far been attributa-ble to technical textiles, followed by home textiles with around 30 percent and the clothing sector with around 10 percent. The vti acts as a stakeholder at state, federal and EU level, tariff- and so-cial partner, as well as a service provider for its around 160 member companies.

(c) Pixabay
15.12.2020

Protection against Corona: Materials research provides findings at institutes of the Zuse Community

As the year draws to a close, expectations are growing that protection against COVID-19 will soon be available. Until this is the case for large sections of the population, the successes achieved in research and industry to protect against the virus in 2020 offer a good starting point in the fight against corona and beyond. At institutes in the Zuse community, progress have been made not only in medical but also in materials research.

As the year draws to a close, expectations are growing that protection against COVID-19 will soon be available. Until this is the case for large sections of the population, the successes achieved in research and industry to protect against the virus in 2020 offer a good starting point in the fight against corona and beyond. At institutes in the Zuse community, progress have been made not only in medical but also in materials research.

These successes in materials research include innovations in the coating of surfaces. "In the wake of the pandemic, the demand for antiviral and antimicrobial surfaces has risen sharply, and we have successfully intensified our research in this area," explains Dr. Sebastian Spange, Head of Surface Technology at the Jena research institute INNOVENT. He expects to see an increasing number of products with antiviral surfaces in the future. "Our tests with model organisms show that an appropriate coating of surfaces works", emphasizes Spange. The spectrum of techniques used by INNOVENT includes flame treatment, plasma coating and the so-called Sol-Gel process, in which organic and inorganic substances can be combined in one layer at relatively low temperatures. According to Spange, materials for the coatings can be antibacterial metal compounds as well as natural substances with antiviral potential.

Nonwovens produced for mask manufacturers
In 2020, the textile expertise of numerous institutes in the Zuse community ensured that application-oriented research could prove its worth in the practical fight against pandemics. After the shortage of mask supplies in Germany at the beginning of the pandemic, textile research institutes reacted to the shortage by jumping into the breach. The Saxon Textile Research Institute (STFI), for example, converted its research facilities to the production of nonwovens to supply German and European manufacturers of particle filtering protective masks. "From March to November 2020, we supplied nonwovens to various manufacturers in order to provide the best possible support for mask production and thus help contain the pandemic. At a critical time for industry and the population, we were able to help relieve critical production capacity - an unaccustomed role for a research institute, but one we would assume again in similar situations," explains Andreas Berthel, Managing Commercial Director of STFI.

Development of reusable medical face masks
For the improvement of everyday as well as medical face masks the German Institutes for Textile and Fiber Research (DITF) are working on this project. In cooperation with an industrial partner, they are currently developing in Denkendorf, among other things, reusable medical face masks made of high-performance precision fabric using Jacquard weaving technology. The multiple use avoids waste and possible supply bottlenecks.

There are regulations for all types of masks, now also for everyday masks. At Hohenstein, compliance with standards for masks is checked. A new European guideline defines minimum requirements for the design, performance evaluation, labelling and packaging of everyday masks. "As a testing laboratory for medical products, we test the functionality of medical masks from microbiological-hygienic and physical aspects", explains Hohenstein's Managing Director Prof. Dr. Stefan Mecheels. In this way, Hohenstein supports manufacturers, among other things, with technical documentation to prove the effectiveness and safety. Respiratory protection masks (FFP 1, FFP 2 and FFP 3) have been tested at the Plastics Centre (SKZ) in Würzburg since the middle of this year. Among other things, inhalation and exhalation resistance and the passage of particles are tested. In addition, SKZ itself has entered into mask research. In cooperation with a medical technology specialist, SKZ is developing an innovative mask consisting of a cleanable and sterilizable mask carrier and replaceable filter elements.

ILK tests for mouth-nose protection
The fight against Corona is won by the contributions of humans: Of researchers in laboratories, of developers and manufacturers in the Industry as well as from the citizens on the street.
Against this background, the Institute for Air and Refrigeration Technology (ILK) in Dresden has carried out investigations into the permeability of the mouth and nose protection (MNS), namely on possible impairments when breathing through the mask as well as the protective function of everyday masks. Result: Although the materials used for the mouth-nose protection are able to retain about 95 percent of the exhaled droplets, "under practical aspects and consideration of leakages" it can be assumed that about 50 percent to 70 percent of the droplets enter the room, according to the ILK. If the mask is worn below the nose only, it can even be assumed that about 90 percent of the exhaled particles will enter the room due to the large proportion of nasal breathing. This illustrates the importance of tight-fitting and correctly worn mouth and nose protection. "On the other hand, from a physical point of view there are no reasons against wearing a mask", ILK managing director Prof. Dr. Uwe Franzke emphasizes. The researchers examined the CO2 content in the air we breathe as well as the higher effort required for breathing and based this on the criterion of overcoming the pressure loss. "The investigations on pressure loss showed a small, but practically irrelevant increase," explains Franzke.

The complete ILK report "Investigations on the effect of mouth and nose protection (MNS)" is available here.

Venue Messe Frakfurt (c) Mese Frankfurt GmbH
22.09.2020

Heimtextil 2021 to be held in May

The next Heimtextil has been postponed from January and will now be held concurrently with Techtextil and Texprocess 2021 in Frankfurt from 4 to 7 May 2021. This will result in exciting synergistic effects for the sector.
 
The current situation with respect to the corona pandemic and the associated international travel restrictions have caused Messe Frankfurt to postpone the next Heimtextil, the world’s biggest trade fair for home and contract textiles, from the planned dates in January until 4 to 7 May 2021.
     

The next Heimtextil has been postponed from January and will now be held concurrently with Techtextil and Texprocess 2021 in Frankfurt from 4 to 7 May 2021. This will result in exciting synergistic effects for the sector.
 
The current situation with respect to the corona pandemic and the associated international travel restrictions have caused Messe Frankfurt to postpone the next Heimtextil, the world’s biggest trade fair for home and contract textiles, from the planned dates in January until 4 to 7 May 2021.
     
“The bulk of the international home and contract textiles sector want us to hold Heimtextil 2021. Many companies are hoping to give their businesses a boost by taking part in the fair following the restart. And we consider it a greater obligation than ever before that we play our part in this”, explains Detlef Braun, Member of the Executive Board of Messe Frankfurt. “However, the current travel restrictions and the renewed increase in the number of infections represent a big hurdle for our very international trade fair. We are in constant contact with our exhibitors and the appropriate authorities and will do everything in our power to ensure a safe and successful Heimtextil 2021.”

Over 90 percent of exhibitors come to Heimtextil in Frankfurt from outside Germany. As part of the preparatory work for an international trade fair of this kind in January, it is necessary, for example, to commission stand-construction companies, ship the goods and book flights and hotels in September. Thus, in view of the current travel restrictions, holding Heimtextil 2021 in May instead of January offers greater planning certainty for all involved.
 
“The trend-oriented order cycles of the home and contract textiles sector require an annual event towards the beginning of the year. Techtextil and Texprocess are biennial trade fairs and are next due to be held in May 2021. For Heimtextil, this is an opportunity to join forces with the two internationally successful textile trade fairs and present the entire textile value chain simultaneously at Frankfurt Fair and Exhibition Centre”, says Olaf Schmidt, Vice President Textiles and Textile Technologies.

Additionally, holding Heimtextil concurrently with Techtextil, the leading international trade fair for technical textiles and nonwovens, and Texprocess, the leading international trade fair for processing textile and flexible materials, offers a host of exciting synergistic effects for the sector.

The close proximity to suppliers and buyers of technical textiles and nonwovens with innovative functionalities, as well as machines and the latest technologies for processing textile and flexible materials, is certain to generate interesting new perspectives for both visitors and exhibitors of Heimtextil. Indeed, the two textile fairs already aim at the home-textile sector with the ‘Hometech’ segment.
 
“We are confident that the situation with respect to the corona pandemic will have eased significantly by May, next year, and are looking forward to holding a successful and safe event together with our partners from the sector”, says Olaf Schmidt.

NEU: Nextrade - the digital marketplace
For the first time, Messe Frankfurt will provide a supplementary digital service in connection with Heimtextil 2021: Nextrade, an order and data-management portal offering new opportunities through digital 24/7 business relationships between trade-fair participants, especially against the background of the Covid-19 pandemic. There, dealers can place their orders with suppliers around the clock and, therefore, do so independently of any official pandemic regulations applying at the time. Nextrade also offers suppliers completely new sales and distribution channels, especially internationally. Nextrade was launched in conjunction with the Ambiente, Tendence and Nordstil consumer-goods and lifestyle trade fairs. As the first digital B2B market place for home and living, the portal brings together demand and supply from the whole sector and thus produces great value added for both sides:: www.nextrade.market

Techtextil / Texprocess
At the biennial Techtextil, the leading international trade fair for the sector in Frankfurt am Main, international exhibitors present the complete spectrum of technical textiles, functional apparel textiles and textile technologies for all areas of application. Techtextil is held concurrently with Texprocess, the leading trade for the garment and textile processing industry, which is aimed primarily at manufacturers of garments, fashions, upholstered furniture and leather products.

More information:
Heimtextil 2021
Source:

Messe Frankfurt GmbH

Photo: Pixabay
28.04.2020

Meltblown Productive: Fraunhofer ITWM vs. Corona - With Mathematics Against the Crisis

  • Meltblown Productive – ITWM Software Supports Nonwoven Production for Infection Protection

Simulations by the Fraunhofer Institute for Industrial Mathematics ITWM make processes in the manufacturing of nonwovens more efficient. Within the anti-corona program of Fraunhofer the production of infection protection is optimized.
 
Nonwovens production is currently attracting more attention than ever before from the general public, because in times of the corona pandemic, nonwovens are vital for infection protection in the medical sector and also for the protection of the entire population. Disposable bed linen in hospitals, surgical gowns, mouthguards, wound protection pads and compresses are some examples of nonwoven products.

  • Meltblown Productive – ITWM Software Supports Nonwoven Production for Infection Protection

Simulations by the Fraunhofer Institute for Industrial Mathematics ITWM make processes in the manufacturing of nonwovens more efficient. Within the anti-corona program of Fraunhofer the production of infection protection is optimized.
 
Nonwovens production is currently attracting more attention than ever before from the general public, because in times of the corona pandemic, nonwovens are vital for infection protection in the medical sector and also for the protection of the entire population. Disposable bed linen in hospitals, surgical gowns, mouthguards, wound protection pads and compresses are some examples of nonwoven products.

IEspecially in intensive care and geriatric care, disposable products made of nonwovens are used due to the special hygiene requirements. At the moment there are clear bottlenecks in the production of these materials. For the meltblown nonwovens class, however, it is difficult to increase production efficiency because meltblown processes are highly sensitive to process fluctuations and material impurities.
 
Although nonwovens are not all the same, the rough principle of their production is relatively similar to all industrially manufactured nonwovens: molten polymer is pressed through many fine nozzles, stretched and cooled down in an air stream and thus deposited into the typical white webs. "Meltblown" stands for the submicron fiber process whose nonwovens are responsible for the decisive filter function in face masks.
 
With meltblown technology, nonwoven fabrics are produced directly from granules. A special spinning process in combination with high-speed hot air is used to produce fine-fibered nonwovens with different structures. The fibers are highly stretched by the turbulent air flow. During this process they swirl in the air, become entangled and fall more or less randomly onto a conveyor belt where they are further consolidated - a very complex process. Nonwovens manufacturers around the world are striving to massively increase their production capacities.
 
Digital Twin Optimizes Meltblown Process    
This is where the software of the ITWM comes into play. "Our Fiber Dynamics Simulation Tool FIDYST is used to predict the movement of the fibers, their falling and the orientation with which they are laid down on the conveyor belt. Depending on the process settings, turbulence characteristics are generated and thus nonwoven qualities are created that differ in structure, fiber density and strength," explains Dr. Walter Arne from the Fraunhofer ITWM. He has been working at the institute for years on the simulation of various processes involving fibers and filaments.

The methodology is well transferable to meltblown processes. In these processes, one of the specific features is the simulation of filament stretching in a turbulent air flow - how the stretching takes place, the dynamics of the filaments and the diameter distribution. These are all complex aspects that have to be taken into account, but also the flow field or the temperature distribution. The simulations of the scientists at the Fraunhofer ITWM then provide a qualitative and quantitative insight into the fiber formation in such meltblown processes - unique in the world in this form when it comes to simulate a turbulent spinning process (meltblown).

Nonwoven Manufacturers benefit from Simulation
What does this mean for the industry? The production of technical textiles becomes more efficient, but the nonwovens can also be developed without having intensive productions tests in a real facility. This is because the simulations help to forecast and then optimize the processes using a digital twin. In this way, production capacities can be increased while maintaining the same product quality. Simulations save experiments, allow new insights, enable systematic parameter variations and solve up-scaling problems that can lead to misinvestments during the transition from laboratory to industrial plant.

Making a Contribution to Overcome the Crisis With Many Years of Expertise
"We want to demonstrate this in the project using a typical meltblown line as an example - for this we are in contact with partner companies," says Dr. Dietmar Hietel, head of the department "Transport Processes" at the Fraunhofer ITWM. "Within the framework of Fraunhofer's anti-corona program, we want to use our developed expertise and our network to contribute to overcome the crisis", reports Hietel. His department at the Fraunhofer ITWM has been pursuing research in the field of technical textiles for around 20 years. Due to its current relevance, the project not only got off to a quick start, but the implementation and results should now also be implemented quickly: The project is scheduled to run from April 15th 2020 to August 14th 2020. The kick-off meeting took place on April 17th 2020 via video conference.
 
The project "Meltblown productive" and the results are certainly interesting for nonwoven producers. The production of many mass products has often been outsourced to Asia in the past decades; the nonwovens manufacturers remaining in Germany and Europe tend to focus more on high-quality technical textiles. In the medium and longer term, this will also be a scientific preliminary work when production capacities in Germany and Europe are expanded by new plants. One lesson to be learned from the crisis will also be to reduce the dependence on producers in Asia, especially as a precautionary measure for crisis scenarios.

Source:

Fraunhofer Institute for Industrial Mathematics, ITWM

The new AddiTex compound comes out of the extruder as a filament for 3D printing. © Fraunhofer UMSICHT
12.11.2019

FRAUNHOFER UMSICHT: COMPOUNDS FOR ADDITIVE MANUFACTURING, GEOTEXTILES AND WEARABLES

Whether biodegradable geotextiles, wearables from thermoplastic elastomers or functional textiles from 3D printers - the scope of plastics developed at the Fraunhofer Institute for Environmental, Safety and Energy Technology UMSICHT is wide.

Insights into these projects were provided from October 16th - 23rd  in Düsseldorf: At the K, scientists presented their work on thermally and electrically conductive, biodegradable, bio-based compounds as well as compounds suitable for additive production.
 
Textile composites from the 3D printer
In the "AddiTex" project, plastics were developed that are applied to textiles in layers using 3D printing and give them functional properties. A special challenge in the development was the permanent adhesion: The printed plastic had to be both a strong bond with the textile and sufficiently flexible to be able to participate in movements and twists.

Whether biodegradable geotextiles, wearables from thermoplastic elastomers or functional textiles from 3D printers - the scope of plastics developed at the Fraunhofer Institute for Environmental, Safety and Energy Technology UMSICHT is wide.

Insights into these projects were provided from October 16th - 23rd  in Düsseldorf: At the K, scientists presented their work on thermally and electrically conductive, biodegradable, bio-based compounds as well as compounds suitable for additive production.
 
Textile composites from the 3D printer
In the "AddiTex" project, plastics were developed that are applied to textiles in layers using 3D printing and give them functional properties. A special challenge in the development was the permanent adhesion: The printed plastic had to be both a strong bond with the textile and sufficiently flexible to be able to participate in movements and twists.

A flexible and flame-retardant compound was developed, which is particularly suitable for use in the field of textile sun and sound insulation, as well as a rigid compound, which is used, among other things, for reinforcing the shape of protective and functional clothing.

Geotextile filter for technical-biological bank protection
Geotextile filters for technical-biological bank protection are the focus of the "Bioshoreline" project. It stands for gradually biodegradable nonwovens, which allow a near-natural bank design of inland waterways with plants. They consist of renewable raw materials and are intended to stabilize the soil in the shore area until the plant roots have grown sufficiently and take over both filter and retention functions. The ageing and biodegradation of the fleeces begin immediately after installation, until the fleeces are gradually completely degraded.

Prototypes of the geotextile filters are currently being tested. Female scientists evaluate the plant mass formed above and below ground with and without geotextile filters as well as the influence of the soil type on plant growth and the biological degradation of the filter.

Wearables made of thermoplastic elastomers
In addition, Fraunhofer UMSICHT is developing novel, electrically conductive and flexible compounds that can be processed into thermoplastic-based bipolar plates. These plastics are highly electrically conductive, flexible, mechanically stable, gas-tight and chemically resistant and - depending on the degree of filling of electrically conductive additives - can be used in many different ways. For example, in electrochemical storage tanks (batteries), in energy converters (fuel cells), in chemical-resistant heat exchangers or as resistance heating elements.

Another possible field of application for these plastics: Wearables. These portable materials can be produced easily and cheaply with the new compounds. It is conceivable, for example, to form garments such as a vest by means of resistance heating elements. The idea behind this is called Power-to-Heat and enables the direct conversion of energy into heat.

FUNDING NOTES

"AddiTex" is funded with a grant from the State of North Rhine-Westphalia using funds from the European Regional Development Fund (ERDF) 2014-2020 "Investments in growth and employment". Project Management Agency: LeitmarktAgentur.NRW – Projektmanagement Jülich.

The "Bioshoreline" project (funding reference: 22000815) is funded by the Federal Ministry of Food and Agriculture (BMEL) on the basis of a resolution of the German Bundestag.

More information:
Fraunhofer-Institute UMSICHT K 2019
Source:

Fraunhofer Institute for Environmental, Safety, and Energy Technology UMSICHT

Fotos: (c) ITMA
25.06.2019

A MORE INTERNATIONAL ITMA 2019 SETS NEW RECORD WITH BIGGEST NUMBER OF EXHIBITORS

Since its launch in 1951, ITMA has enjoyed wide industry recognition as the world’s largest textile and garment technology exhibition. This year’s exhibition in Barcelona sees its reputation solidify further with the largest gathering of exhibitors in its history. The record number of exhibitors totaling 1,717 from 45 countries has set a new milestone.

Speaking at the press conference on the opening day of the 18th edition of the exhibition, Mr Fritz P. Mayer, President of the European Committee of Textile Machinery Manufacturers (CEMATEX), said: “The global economy is still facing challenges, accentuated by trade tensions and disruption. However, textile being the world’s oldest manufacturing industry has demonstrated its resilience over the years. 

Since its launch in 1951, ITMA has enjoyed wide industry recognition as the world’s largest textile and garment technology exhibition. This year’s exhibition in Barcelona sees its reputation solidify further with the largest gathering of exhibitors in its history. The record number of exhibitors totaling 1,717 from 45 countries has set a new milestone.

Speaking at the press conference on the opening day of the 18th edition of the exhibition, Mr Fritz P. Mayer, President of the European Committee of Textile Machinery Manufacturers (CEMATEX), said: “The global economy is still facing challenges, accentuated by trade tensions and disruption. However, textile being the world’s oldest manufacturing industry has demonstrated its resilience over the years. 

“This is also the spirit of our exhibitors who continually innovate and launch new technologies and solutions. We are glad that ITMA has been providing a reputable platform for textile machinery manufacturers to market their innovations. This has enabled us to record the largest number of exhibitors in ITMA’s history.”

The exhibits are showcased over 114,500 square metres of net exhibit space, a 9 per cent increase over the previous edition in 2015. The exhibition occupies all nine halls of the Gran Via venue, including the space under the linkway. To allow more companies to participate, many exhibitors were allocated lesser stand space than what they had originally applied for.  

Mr Charles Beauduin, Chairman of ITMA Services, organiser of ITMA 2019 enthused: “The exhibition would have been larger if we had not turned away applicants due to a lack of space. Unfortunately, we could not accommodate a wait-list of about 250 applicants who booked some 8,200 square metres.”

He added: “ITMA has also evolved into a more international exhibition with a rich diversity of technology offerings from both East and West. Almost half of the total number of exhibitors are from non CEMATEX countries. This augurs well for the development of ITMA into a definitive textile and garment platform for the industry.”

International participation
Of the total number of exhibitors, over half are from CEMATEX countries; the balance comprising companies from other parts of Europe, Asia, the Middle East and the Americas. Reflecting the international composition of the participants, the largest number of exhibitors are from Italy (364 exhibitors), China (276 exhibitors), Germany (222 exhibitors), India (169 exhibitors) and Turkey (164 exhibitors).

CEMATEX countries continue to occupy the largest exhibit space, taking up 65% of the total net exhibit space. Italy booked 26% of the space, followed by Germany which booked 18%. The top non-CEMATEX countries are: Turkey with 9%, China with 8%, and India with 5% of the space booked.

Product sectors
Visitors can expect to source a wide range of integrated solutions across the entire value chain in 19 exhibit sectors. Printing, which has seen many advances being made in the last few years, is an exciting growth sector. Chalking up a 38 per cent increase in the number of exhibitors compared with the previous exhibition, it is one of the top five sectors at ITMA 2019:

  • Finishing - 325 exhibitors
  • Spinning - 281 exhibitors
  • Weaving - 182 exhibitors
  • Printing - 157 exhibitors
  • Knitting - 136 exhibitors

Nonwoven and technical textiles due to their wide range of applications continue to be an important sector at ITMA 2019. Garment making, which has been impacted by digitalisation and fast fashion, is also making a bigger impact at ITMA.

Mr Mayer said, “We are extremely pleased to bring garment technology back in focus at ITMA. While ITMA has been traditionally strong in textile making technologies, we are glad that we are able to present garment making solutions from some of the world’s most renowned technology providers. There is an increase of 27 per cent in number of exhibitors as compared with ITMA 2015." Completing the entire value chain is the showcase on fibres, yarn and fabrics. The addition of innovative fabrics in the fibre and yarn chapter at ITMA further completes the sourcing experience for buyers.
 
Focus on innovation
The theme of ITMA 2019 is ‘Innovating the World of Textiles’. To support the innovation drive, CEMATEX has introduced the ITMA Innovation Lab. A new umbrella branding of a series of activities, the Lab includes the Research and Innovation Pavilion, ITMA Speakers Platform, ITMA Sustainable Innovation Award and Innovation Video Showcase. Speakers from the industry have been invited to share their perspectives and experiences at the Speakers Platform which will be held from 21 to 25 June. A finance forum was also held on 21 June.

Co-located events and industry engagement
To encourage the exchange of knowledge, collaboration and networking, several events are staged alongside ITMA 2019. The ITMA-EDANA Nonwovens Forum and Textile Colourant and Chemical Leaders Forum have met with overwhelming response and seats have been added. Similar strong response has also been received by partner events, including the Better Cotton Initiative Seminar, European Digital Textile Conference, TexSummit Global, Planet Textiles, SAC & ZDHC Manufacturer Forum and Texmeeting by TEXFOR.

“The series of co-located events is part of ITMA’s outreach programme to engage industry partners and to create an inclusive platform for the global textile and garment community. We have over 190 international, regional and local organisations lending their support to our exhibition,” Mr Mayer said. ITMA 2019 is held at Fira de Barcelona Gran Via venue till 26 June. The opening hours are from 10.00am to 6.00pm daily, except 26 June when the exhibition will end at 4.00pm.

About CEMATEX & ITMA
The European Committee of Textile Machinery Manufacturers (CEMATEX) comprises national textile machinery associations from Belgium, France, Germany, Italy, Netherlands, Spain, Sweden, Switzerland and the United Kingdom. It is the owner of ITMA and ITMA ASIA. Considered the ‘Olympics’ of textile machinery exhibitions, ITMA has a 68-year history of displaying the latest technology for every single work process of textile and garment making. It is held every four years in Europe.

 

More information:
ITMA 2019
Source:

CEMATEX & ITMA Services