Aus der Branche

Zurücksetzen
23 Ergebnisse
(c) A. Monforts Textilmaschinen GmbH & Co. KG
05.01.2024

Monforts: New Stenter line installed at Curt Bauer

Monforts' new Montex 8500 stenter line was recently installed at Curt Bauer’s plant in Aue in Germany.

Curt Bauer has been in continuous operation for 150 years, beginning as a weaving mill in Aue in the Ore Mountains region of Saxony back in 1882. Today, with 120 employees, the company has an annual production of 2.2 million metres of fabric and specialises in three key fields – home textiles, special damask fabrics for West African garments and technical textiles.

A first Montex stenter was installed by Monforts at the Aue plant in 2003 and an older machine from a third party supplier was also still in operation prior to the latest upgrade.
“The replacement of our older existing stenter, which was installed in 1985, was long overdue,” explains Gert Bauer. “It had a maximum working width of 2.2 metres and we were looking to both increase productivity and reduce energy requirements.”

Monforts' new Montex 8500 stenter line was recently installed at Curt Bauer’s plant in Aue in Germany.

Curt Bauer has been in continuous operation for 150 years, beginning as a weaving mill in Aue in the Ore Mountains region of Saxony back in 1882. Today, with 120 employees, the company has an annual production of 2.2 million metres of fabric and specialises in three key fields – home textiles, special damask fabrics for West African garments and technical textiles.

A first Montex stenter was installed by Monforts at the Aue plant in 2003 and an older machine from a third party supplier was also still in operation prior to the latest upgrade.
“The replacement of our older existing stenter, which was installed in 1985, was long overdue,” explains Gert Bauer. “It had a maximum working width of 2.2 metres and we were looking to both increase productivity and reduce energy requirements.”

As a consequence, the company opted for a new Montex 8500 line with a working width of 3.2 metres equipped with the MonforClean heat recovery and exhaust air purification system. The Montex stenter remains unmatched in terms of its robustness and long service life and with MonforClean technology, the waste heat from the drying process is used to pre-heat the drying air. This results in a radical reduction in the conventional heat supply required, compared to full gas and thermal oil heating. Overall energy savings of up to 40% can now be achieved compared to conventional stenters.

The first challenge at the Aue plant was how to fit the significantly larger machine into the available space without restricting the area required for docking operations.

The special multi-level configuration that Monforts designers and Curt Bauer’s team devised in order to meet these requirements involved raising all of the line’s drying zones – with a combined length of over 28 metres – on scaffolding platforms, to enable the ground floor space below them to continue to be fully utilised.

The next challenge involved configuring the MonforClean system without having to make any costly changes to the roofing structure. This, Gert Bauer observes, demanded “millimetre precision”.

With the new line now fully operational, the savings it is providing have yet to be fully calculated.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG

Monforts: Solid Success at ITMA 2023 Photo: Monforts / AWOL Media
07.07.2023

Monforts: Solid Success at ITMA 2023

Finishing machinery specialist Monforts has secured a number of major orders from textile manufacturers in Central and South America recently, and was pleased to welcome a high number of visitors from the region to its stand at ITMA 2023 in Milan from June 8-14.

Among new orders are those for three Montex stenters delivered to the AustralTex Group in Argentina and a further Montex range to denim manufacturer CIT in Brazil. Guatemala’s Global Textiles placed an order for its second Montex stenter, while Mexico’s Zentrix ordered its third and Avante, also in Mexico, has opted for its sixth.

Elsewhere, orders have also been placed for the delivery of three new Montex stenters to one of Pakistan’s major corporations, as well as a new Thermex dyeing range to nonwovens manaufacturer Orsa in Italy. Further orders – both for new machines and retrofit modules – are now anticipated following ITMA 2023, which attracted over 111,000 visitors to Milan.

Finishing machinery specialist Monforts has secured a number of major orders from textile manufacturers in Central and South America recently, and was pleased to welcome a high number of visitors from the region to its stand at ITMA 2023 in Milan from June 8-14.

Among new orders are those for three Montex stenters delivered to the AustralTex Group in Argentina and a further Montex range to denim manufacturer CIT in Brazil. Guatemala’s Global Textiles placed an order for its second Montex stenter, while Mexico’s Zentrix ordered its third and Avante, also in Mexico, has opted for its sixth.

Elsewhere, orders have also been placed for the delivery of three new Montex stenters to one of Pakistan’s major corporations, as well as a new Thermex dyeing range to nonwovens manaufacturer Orsa in Italy. Further orders – both for new machines and retrofit modules – are now anticipated following ITMA 2023, which attracted over 111,000 visitors to Milan.

“Visitor footfall at ITMA 2023 was well beyond the company’s expectations, and we were especially pleased at the constant number of visitors from South American companies, as well as from Asia and Europe,” said Monforts Marketing Manager Nicole Croonenbroek. “We were able to provide them with detailed information about our portfolio of machines and technologies digitally and fielded an unprecedented number of serious enquiries, many of which promise to turn into new business.”

Monforts Montex stenters for processes such as drying, stretching, heat-setting and coating, she added, are already the industry standard for the fabric finishing industry, providing a number of advantages in terms of production throughput and especially in energy efficiency and resource savings. Other key technologies in the Monforts portfolio include relaxation dryers, Thermex dyeing ranges and Monfortex compressive shrinking ranges.

Montex®Coat
“We were also very pleased with the interest in the Montex®Coat, the latest addition to our range of technologies, which we displayed in Milan,” Croonenbroek said.

The Montex®Coat can serve a very diverse number of markets and enables full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments, as well as solvent coatings. Knife coating, roller coating or screen printing can also all be accommodated with this system. It provides the ultimate in flexibility and the ability to switch quickly from one fabric run to the next, without compromising on the economical use of energy or raw materials.

Many refinements have been made to the Montex®Coat in the past few years, resulting in higher coating accuracy and the resulting quality of the treated fabrics. A number of advanced new improvements were introduced in Milan, including automatic edge limiters for immediately adapting to new coating widths and a new and simplified hand-held control device. These save considerable time in setting up the machine and ensuring consistent production.

The Montex®Coat unit displayed in Milan was sold to Vietnamese company Thai Tuan during the show.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG

(c) A. Monforts Textilmaschinen GmbH & Co. KG
Members and associates of the WasserSTOFF consortium from Monforts, Pleva, NTB Nova Textil, TU Freiberg, Hochschule Niederrhein and Honeywell Thermal Solutions, at the launch meeting of the new project at the Monforts ATC in Mönchengladbach.
28.04.2023

Monforts presents green hydrogen project WasserSTOFF at ITMA 2023

At ITMA 2023 in Milan from June 8-14 this year, Monforts is organising two free-to-attend seminars and discussions on the potential of green hydrogen as a new energy source for textile finishing, drying and related processes.

Monforts is currently leading a consortium of industrial partners and universities in the three-year WasserSTOFF project, launched in November 2022, that is exploring all aspects of this exciting and fast-rising new industrial energy option.
The target of the government-funded project is to establish to what extent hydrogen can be used in the future as an alternative heating source for textile finishing processes. This will first involve tests on laboratory equipment together with associated partners and the results will then be transferred to a stenter frame at the Monforts Advanced Technology Center (ATC).

At ITMA 2023 in Milan from June 8-14 this year, Monforts is organising two free-to-attend seminars and discussions on the potential of green hydrogen as a new energy source for textile finishing, drying and related processes.

Monforts is currently leading a consortium of industrial partners and universities in the three-year WasserSTOFF project, launched in November 2022, that is exploring all aspects of this exciting and fast-rising new industrial energy option.
The target of the government-funded project is to establish to what extent hydrogen can be used in the future as an alternative heating source for textile finishing processes. This will first involve tests on laboratory equipment together with associated partners and the results will then be transferred to a stenter frame at the Monforts Advanced Technology Center (ATC).

To be considered “green”, hydrogen must be produced using a zero-carbon process that is powered by renewable energy sources such as wind or solar. Currently, the cleanest method of hydrogen production is electrolysis, using an electrically-powered electrolyzer to separate water molecules into hydrogen and oxygen. The purity of the hydrogen is also important, and impurities must be removed via a separation process.

“Despite all its advantages, there are obstacles to overcome on the way to widespread, economically-feasible green hydrogen use,” explains Monforts Textile Technologies Engineer Jonas Beisel. “Until there are widely available, reliable and economical sources of this clean power, the cost of producing it will remain prohibitive. The infrastructure is not yet there, and hydrogen also has a tendency to make steel brittle and subject to fracture, which is something that requires further investigation in both its transportation and use in industrial processing.
“Green energy’s potential as a clean fuel source is tremendous, but there is much we need to explore when considering its use in the textile finishing processes carried out globally on our industry-leading Montex stenter dryers and other machines.”

At its Advanced Technology Center (ATC) in Mönchengladbach, Monforts will be carrying out intensive tests and trials to assess the reliability of both processes and final products when different natural gas and hydrogen mixtures – up to 100% green hydrogen – are employed. The results will be closely analysed by the consortium partners because there are many parameters that at this stage remain unknown.

The aim, Beisel adds, is to both reduce CO2 emissions and – following the rising prices and industry turbulence experienced by manufacturers over the past year or so – to further reduce a dependency on natural gas.

The three-year WasserSTOFF project is sponsored by Germany’s Federal Ministry for Economic Affairs and Climate Action, and with Monforts at the helm brings together industrial partners Pleva and NTB Nova Textil, with academic input from the Hochschule Niederrhein and the Technical University of Freiberg.

18.11.2022

Monforts at Igatex 2022

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts will be presenting its finishing technologies at the forthcoming Igatex textile machinery exhibition, which takes place from December 1-4 at the Lahore Expo Centre in Pakistan.

The importance of the textile industry to Pakistan’s economy cannot be overstated – it accounts for 60% of the country’s overall exports and some of its industry’s players are very major employers. In the year to June 2022, Pakistan’s textile exports climbed by 25% to a record value of $19.3 billion according to the country’s Bureau of Statistics, as security of deliveries – especially to Europe and the USA – worked in the country’s favour, in the light of the Covid-19 pandemic and subsequent supply chain issues. It has a key role to play in quickly getting the country back on its feet after the devastation.

Monforts customers in the regions around the country’s three biggest cities of Karachi, Lahore and Faisalbad include all of the main players in the fields of home textiles and denim production, including Afroze, , Al Karam Artistic Milliners, Azgard-9, Crestex, , Gul Ahmed, Interloop, Liberty Mills, Lucky Textile Mills, Mustaqim, Naveena (NDL), Rajby Industries, Sapphire Finishing, Soorty, Style Textile and US Denim.

These companies rely on established Monforts technologies including Montex stentering equipment, Monfortex sanforizing units and Thermex dyeing ranges. The company’s Matex Eco Applicator minimum application system has also proved a big hit in recent years.

Monforts has also achieved considerable success in Pakistan with its Econtrol®* dyeing system  – an effective and established dyeing process. More than 40 Thermex continuous dyeing ranges have been installed in Pakistan in recent years and operator training on the Econtrol®* process by sophisticated technologists is an additional service.

The Econtrol® pad-dry process has a number of immediate benefits. Compared to the common pad-dry-pad-steam process, no salt is used and no steamer is required for a separate fixation step. Compared to the pad-dry-thermofix process, no urea is used and no smoke or deposits are generated, and unlike with the cold pad batch process, direct feedback of the dyeing results ensures no batching time is necessary and guarantees good reproducibility from the lab to bulk production.

An immediate wash off is also unnecessary, allowing for flexible production planning. The process is suitable for pale to dark shades with very good fastness properties. Also waste water treatment is improved by this technology.

*Econtrol is a registered mark of Dystar Colours Distribution GmbH.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

08.09.2022

Monforts at ITMA ASIA + CITME

Monforts will highlight its technologies for special technical textile applications at this year’s ITMA ASIA + CITME which takes place at the National Exhibition and Convention Center in Shanghai, China, from November 20-24.

One of Monforts' developments is the Montex 8500 XXL stenter system for the production of technical fabrics in widths of up to 6.8 metres. Among the products made on this system are treated nonwovens for the geotextiles and filter media markets, tarpaulins, advertising banners, black-out curtains, membranes and many more.

On Montex©Coat coating lines, meanwhile, the possibilities range from the single-sided application of finishing agents for outdoor clothing and adding functionality to home textiles, to the creation of materials for sophisticated lightweight construction and automotive and aerospace components.

Monforts will highlight its technologies for special technical textile applications at this year’s ITMA ASIA + CITME which takes place at the National Exhibition and Convention Center in Shanghai, China, from November 20-24.

One of Monforts' developments is the Montex 8500 XXL stenter system for the production of technical fabrics in widths of up to 6.8 metres. Among the products made on this system are treated nonwovens for the geotextiles and filter media markets, tarpaulins, advertising banners, black-out curtains, membranes and many more.

On Montex©Coat coating lines, meanwhile, the possibilities range from the single-sided application of finishing agents for outdoor clothing and adding functionality to home textiles, to the creation of materials for sophisticated lightweight construction and automotive and aerospace components.

“Many more applications are possible, such as the overdyeing of denim, the creation of double-face coated materials, fabrics awnings, tents and medical drapes and the pre-treatment of substrates for digital printing”, explains Gunnar Meyer, Monforts area sales manager for China. “A range of different doctor blades and their combinations can be supplied to meet individual requirements, including air knife, roller knife, foam, screen and magnetic roller coating. The latter option is recommended for lines with working widths of over 2.4 metres.”

In addition, Monforts can provide the necessary explosion-proof ranges for solvent-based coatings and high temperature processes up to 320°C, such as the PTFE coating of nonwoven filter material. These lines are equipped with special burners, stenter chains, and insulation.

Quelle:

 A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) A. Monforts Textilmaschinen GmbH & Co. KG
07.07.2022

Monforts: New orders for machines at Techtextil 2022

The recent Techtextil show in Frankfurt emphasised the diversity of applications for nonwovens and technical textiles, according to finishing technology specialist Monforts.

“We fielded enquiries at top management level from an extremely wide range of companies, all with very different ideas for new product applications during the show,” said Alexander Fitz, who joined the company a year ago as engineer for textile technologies and co-ordinator of the Monforts Advanced Technology Centre (ATC). Fitz brings a background in both technical textile technology and processes to the role, having previously worked for a nonwovens machinery builder and a roll-goods manufacturer.

The recent Techtextil show in Frankfurt emphasised the diversity of applications for nonwovens and technical textiles, according to finishing technology specialist Monforts.

“We fielded enquiries at top management level from an extremely wide range of companies, all with very different ideas for new product applications during the show,” said Alexander Fitz, who joined the company a year ago as engineer for textile technologies and co-ordinator of the Monforts Advanced Technology Centre (ATC). Fitz brings a background in both technical textile technology and processes to the role, having previously worked for a nonwovens machinery builder and a roll-goods manufacturer.

Trials
“We are now looking forward to interesting new trials and pilot production runs, as well as the commissioning of new orders for machines resulting from the extremely busy exhibition,” he says. “Obviously, everyone at the moment is looking to make energy savings, and we have developed a range of options for helping companies increase their resource efficiency, both on new lines and as retrofitted systems, but this is not stifling innovation at the new material level.

“There was a lot of interest in what is possible with the Montex®Coat coating system and the range of different techniques it enables, and at our ATC in Mönchengladbach, a Montex®Coat unit is integrated into the full technical textiles pilot line, on which it is possible to run new fabrics in widths of up to 1.8 metres.”

Explosion proof
The technical textiles line at the ATC incorporates a Montex four-chamber stenter and is fitted with an explosion-proof coating application chamber in order to allow treatment to be carried out with organic solvents and other volatile materials.

Every single component within the chamber has to meet the standards of the European Union’s ATEX directives for working in a potentially explosive atmosphere. A range of sensors linked to alarms operate at various levels within the chamber to ensure the specified lower explosion limit (LOL) is never exceeded and the ventilation adapts accordingly.

Advanced functions
Special features on the finishing line relate to further advanced functions such as the ability to treat materials not only at temperatures of up to 320°C, but also to be able to treat the top and bottom faces of certain materials at different temperatures within a single pass through the machine.

To achieve this, the first two chambers of the stenter are fitted with special, heavy duty TwinAir ventilation motors and separate burners for individual top/bottom temperature. A temperature differential of up to 60°C can be achieved between the upper and lower nozzles within the chamber, depending on the treatment paramenters.

Another key feature of the technical textiles line at the ATC is the special stretching device which is capable of pulling ten tons in length and ten tons in width – a huge amount per square metre of fabric and necessary in the production of materials such as woven or 3D knits for high temperature filter media.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) A. Monforts Textilmaschinen GmbH & Co. KG
20.06.2022

Monforts introduces range of modular upgrades

Monforts is introducing a range of modular upgrades that can be added to existing finishing lines already in production.

The Monforts universal Energy Tower – a flexible, free-standing air/air heat exchanger for recovering the heat from the exhaust air flow of thermal processes – can result in a 30% reduction in the energy consumed by a line, depending on the exhaust air volume and operating temperature.

A Monforts Eco Booster, completely integrated into the chamber design of the Montex stenter, is another retrofitting option. As a single state-of-the-art heat recovery system with automatic cleaning, it can be added to existing ranges. For ranges of up to eight chambers only one module is necessary to achieve significant energy savings.

On an eight-chamber stenter with an operating width of two metres carrying out a fixing process on a 150gsm woven fabric, for example, the energy savings have been calculated to be 35% over an annual schedule of 6,000 operating hours.

In addition, the Eco Booster consumes only minimal amounts of water during the cleaning cycle and the entire process is controlled and monitored automatically.

Monforts is introducing a range of modular upgrades that can be added to existing finishing lines already in production.

The Monforts universal Energy Tower – a flexible, free-standing air/air heat exchanger for recovering the heat from the exhaust air flow of thermal processes – can result in a 30% reduction in the energy consumed by a line, depending on the exhaust air volume and operating temperature.

A Monforts Eco Booster, completely integrated into the chamber design of the Montex stenter, is another retrofitting option. As a single state-of-the-art heat recovery system with automatic cleaning, it can be added to existing ranges. For ranges of up to eight chambers only one module is necessary to achieve significant energy savings.

On an eight-chamber stenter with an operating width of two metres carrying out a fixing process on a 150gsm woven fabric, for example, the energy savings have been calculated to be 35% over an annual schedule of 6,000 operating hours.

In addition, the Eco Booster consumes only minimal amounts of water during the cleaning cycle and the entire process is controlled and monitored automatically.

The Matex Eco Applicator is an alternative to the conventional padding process for energy-conscious finishing and achieving considerable savings in the energy required for drying treated fabrics. The precise amount of chemical can be applied to the fabric and with less residual moisture after application of only approximately 35% so that less drying capacity is required in the stenter, which leads to huge energy savings.

Finishes can be evenly applied on either or both sides of the fabric, and two separate treatments can be applied to front and back. This makes the unit ideal for the production of, for example, double-performance hydrophobic/hydrophilic fabrics for professional clothing, as well as the over dyeing or finishing of denim fabrics.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

(c) A. Monforts Textilmaschinen GmbH & Co. KG
07.04.2022

Montex stenter at ITM

Monforts and its Turkish representative Neotek are looking forward to the forthcoming ITM 22 international textile machinery show taking place from June 14-18 at the Tüyap Fair and Congress Centre in Istanbul, after a three-year break.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying. The resulting constant evaporation rate within the stenter ensures optimum energy utilisation and also avoids markings on the fabric.

With the latest Montex stenters, overall energy savings of up to 40% can now be achieved compared to a conventional stenter with no heat recovery or energy optimisation measures like high-quality chamber insulation.

Monforts and its Turkish representative Neotek are looking forward to the forthcoming ITM 22 international textile machinery show taking place from June 14-18 at the Tüyap Fair and Congress Centre in Istanbul, after a three-year break.

With the TwinAir heating chamber system within a Montex stenter, top and bottom airflows can be regulated completely independently of each other, ensuring heat is only applied when and where it is required. The Optiscan balancing system ensures continuous automatic evaluation of the distance between the nozzles and the fabric for highly economical and contact-free drying. The resulting constant evaporation rate within the stenter ensures optimum energy utilisation and also avoids markings on the fabric.

With the latest Montex stenters, overall energy savings of up to 40% can now be achieved compared to a conventional stenter with no heat recovery or energy optimisation measures like high-quality chamber insulation.

The Montex stenter also benefits from full digital control, with the Qualitex 800 PLC control system providing ease of operation and rapid access to line and management data, including full operating cost overviews, as well as maintenance monitoring.

Advances in digital technology mean that there are also now significant gains to be made in the retrofitting of existing Monforts machines with the latest automatic drives and control systems, going far beyond the basic replacement of spare parts.

“We will be emphasising the robustness and versatility of the Montex stenter for essential processes such as drying, stretching, heatsetting and coating at the Istanbul show,” said Monforts Area Sales Manager Thomas Päffgen.

“With energy prices rising steeply everywhere, features such as the MonforClean system, or the EcoBooster, in which waste heat from the drying process is used to pre-heat the drying air, are proving more invaluable than ever,” added Ahmet Kilic of Neotek. “Monforts can provide a range of further resource-saving and energy recovery options tailored to each individual line installation.”

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG

Monforts: A complete finishing line upgrade for Wülfing (c) A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media
A completely new joint control system joins the two machines seamlessly.
06.07.2021

Monforts: A complete finishing line upgrade for Wülfing

Wülfing GmbH is one of the oldest but also one of the most modern home textiles companies in Germany, with its main weaving and finishing operations located in Borken, North Rhine-Westphalia, and a further jacquard weaving mill in Steinfurt, as well as with a making up and packaging plant in the Czech Republic.

At its Borken plant, Wülfing has employed a Monforts sanforizing line since 2009 to guarantee the required dimensional stability and shrink-fastness of its high quality bed linen. With a working width of over three metres, the sanforizing process is a central pillar in the production of typical wide-width cotton fabrics for home textiles.

In 2017, the company was able to acquire a second Monforts sanforizing line from another company which, although built in 2005, had been virtually unused. It was overhauled and installed behind a Monforts equalizing frame of a similar age.

“Unfortunately, the two machines had to be operated separately via individual controls and did not represent an integrated unit,” says Schulte-Mesum. “This resulted in deficits in the desired productivity and in the control technology.”

Wülfing GmbH is one of the oldest but also one of the most modern home textiles companies in Germany, with its main weaving and finishing operations located in Borken, North Rhine-Westphalia, and a further jacquard weaving mill in Steinfurt, as well as with a making up and packaging plant in the Czech Republic.

At its Borken plant, Wülfing has employed a Monforts sanforizing line since 2009 to guarantee the required dimensional stability and shrink-fastness of its high quality bed linen. With a working width of over three metres, the sanforizing process is a central pillar in the production of typical wide-width cotton fabrics for home textiles.

In 2017, the company was able to acquire a second Monforts sanforizing line from another company which, although built in 2005, had been virtually unused. It was overhauled and installed behind a Monforts equalizing frame of a similar age.

“Unfortunately, the two machines had to be operated separately via individual controls and did not represent an integrated unit,” says Schulte-Mesum. “This resulted in deficits in the desired productivity and in the control technology.”

Wülfing consulted with Monforts on a number of upgrade options and opted for a completely new joint control system to merge the two machines, as well as a new connecting inlet, a tensioning and damping field and a steaming unit.

“Monforts provided a fast and precise erection and commissioning of the technology in spite of the difficult pandemic circumstances,” says Schulte-Mesum. “The result has been an increase in production speeds by 20% and enhanced uniformity in fabric width through a much improved guidance system.

“We are also achieving energy savings as a result of the new control and drive technology and operation has been simplified and improved as a result of the unified control. We benefit from simplified access for maintenance work such as the grinding of the rubber blanket, but most of all we have greatly improved our flexibility and now have two almost identical Monforts sanforizing lines.”

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

Monforts takes part in Webtalk by VDMA’s textile machinery division (c) Monforts/Pleva
13.05.2021

Monforts takes part in Webtalk by VDMA’s textile machinery division

Monforts Head of Technical Textiles Jürgen Hanel will take part in the next international webtalk to be held by the VDMA’s textile machinery division on May 20th.

He will be joined by Johannes Lutz, Research and Development Engineer at Pleva, to provide full details of how the latest Monforts coating technology is supported by special microwave measuring systems.

The Montex®Coat magnetic roller coating option allows a wide range of coatings and finishes to be carried out, while being easy to handle for operators and much easier to clean at the end of the process.

“This roller provides textile finishers with an expanded range of options due to the fully-adjustable positioning of the magnet within the roller and with four different magnet positions possible, can be set to operate both as a direct coating system and as an indirect coater,” Hanel said.

Lutz will provide an overview of the use of Pleva microwave measurement technology in coating processes, in addition to the latest developments in electronic evaluation.

Monforts Head of Technical Textiles Jürgen Hanel will take part in the next international webtalk to be held by the VDMA’s textile machinery division on May 20th.

He will be joined by Johannes Lutz, Research and Development Engineer at Pleva, to provide full details of how the latest Monforts coating technology is supported by special microwave measuring systems.

The Montex®Coat magnetic roller coating option allows a wide range of coatings and finishes to be carried out, while being easy to handle for operators and much easier to clean at the end of the process.

“This roller provides textile finishers with an expanded range of options due to the fully-adjustable positioning of the magnet within the roller and with four different magnet positions possible, can be set to operate both as a direct coating system and as an indirect coater,” Hanel said.

Lutz will provide an overview of the use of Pleva microwave measurement technology in coating processes, in addition to the latest developments in electronic evaluation.

To ensure a constant high quality in coating operations it is necessary to accurately measure and control the amount of chemical being applied, and Pleva’s series 700 devices achieve this via contact-free microwave moisture measurement technology which can be supplied either as single- or three-point units, or as a traversing measurement unit.

The free-to-attend webtalk will take place on May 20th from 2-3pm (CEST) and registration can be made here, along with further information.

Quelle:

AWOL Media

Klaus Heinrichs (c) A. Monforts Textilmaschinen GmbH & Co. KG
22.04.2021

Monforts: Vice-President Klaus Heinrichs is to retire at the end of May

Klaus Heinrichs began working in marketing for the company in 1992. “From the very beginning until today Klaus used his great flair and networking skills to secure and improve the company’s international presence and public relations, especially at seven successive ITMA textile machinery exhibitions, beginning with the show in Milan in 1995,” said Monforts Marketing Manager Nicole Croonenbroek.  “Later, he also took care of customer service, sales administration and exports in his uniquely calm and quietly-spoken style.”

“He has always been a guarantor of successful product launches for Monforts technical and technological highlights such as the TwinAir principle of independent airflow regulation, the Hercules LTM stenter chain, the Econtrol® dyeing technology or the Montex®Coat device - to mention only a few.”

Klaus Heinrichs began working in marketing for the company in 1992. “From the very beginning until today Klaus used his great flair and networking skills to secure and improve the company’s international presence and public relations, especially at seven successive ITMA textile machinery exhibitions, beginning with the show in Milan in 1995,” said Monforts Marketing Manager Nicole Croonenbroek.  “Later, he also took care of customer service, sales administration and exports in his uniquely calm and quietly-spoken style.”

“He has always been a guarantor of successful product launches for Monforts technical and technological highlights such as the TwinAir principle of independent airflow regulation, the Hercules LTM stenter chain, the Econtrol® dyeing technology or the Montex®Coat device - to mention only a few.”

Klaus has also been active on the VDMA’s Exhibition and Marketing Committee since 1993, which he chaired from 2005 to 2008.  
“Klaus always enriched the industry discussions with practical and future-oriented proposals and thus also advanced ITMA,” said Thomas Waldmann, Managing Director of the VDMA Textile Machinery Association. “We sincerely thank him and wish him all the best for this new chapter of his life.”

“We will miss Klaus as a colleague and as a manager because of his skills, character and his engagement,” added Monforts Managing Director Stefan Flöth. “He truly represents the Monforts commitment to our customers to be helpful, accurate, fast and reliable, and we keep him as a friend. I’m sure the many friends he made throughout the world during his career with the company will join us in wishing him all the best for his next phase of life together with his family.”


* Econtrol is a registered trademark of Dystar Colours Distribution GmbH.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG

How to do more with less explored at Kingpins24 Flash (c) Monfords
Monforts has a leading position in the field of denim finishing with its well proven Thermex continuous dyeing systems, Montex stenter dryers and other lines for resource-efficient and economical processing.
09.03.2021

How to do more with less explored at Kingpins24 Flash

  • Major Monforts denim customers continue to pioneer new initiatives that are pushing the boundaries of sustainable production.

Recycling their cotton waste has become one way these companies can do more with less, and at the recent Kingpins24 Flash online event, Sedef Uncu Aki, director of Orta, headquartered in Istanbul, Turkey, announced a new partnership with leading recycling operation Gama Recycle.

Traceable
“Through this local partnership we will supply the waste from our spinning mills and return around 3,000 tons of premium quality cotton back to them,” she said. “We have established a truly controlled and traceable system and partnering with a domestic recycling centre is important because a lot the carbon emissions associated with recycling usually come from transportation.”

  • Major Monforts denim customers continue to pioneer new initiatives that are pushing the boundaries of sustainable production.

Recycling their cotton waste has become one way these companies can do more with less, and at the recent Kingpins24 Flash online event, Sedef Uncu Aki, director of Orta, headquartered in Istanbul, Turkey, announced a new partnership with leading recycling operation Gama Recycle.

Traceable
“Through this local partnership we will supply the waste from our spinning mills and return around 3,000 tons of premium quality cotton back to them,” she said. “We have established a truly controlled and traceable system and partnering with a domestic recycling centre is important because a lot the carbon emissions associated with recycling usually come from transportation.”

Orta’s ZeroMax range meanwhile uses no cotton at all, being based on Lenzing’s Tencel cellulosic fibre, while the company’s involvement in denim production for a recent launch by Levi Strauss, of jeans made with organic cotton and Circulose – a breakthrough material developed by re:newcell of Sweden and partners – was hailed as a further step forward.

To make Circulose, re:newcell repurposes discarded cotton textiles, such as worn-out denim jeans, through a process akin to recycling paper. The incoming waste fabrics are broken down using water. The colour is then stripped from these materials using an eco-friendly bleach and after any synthetic fibres are removed from the mix, the slurry-like mixture is dried and the excess water is extracted, leaving behind a sheet of Circulose. This sheet is then made into viscose fibre which is combined with cotton and woven into new fabrics.

Circular Park
Omer Ahmed, CEO of Artistic Milliners also announced plans for his company’s new 70,000 square-foot Circular Park in Karachi, Pakistan, at Kingpins24 Flash.

Once complete, this will add three million square metres of additional denim capacity a month to the company’s production and take its total recycled output to a monthly five million metres.
Ahmed observed that there is currently a lack of sustainable fibres that are readily available to use for denim production at scale.

“Organic cotton is too expensive, and in my opinion always will be,” he said. “Cottonised hemp is also not cheap and it’s hard to mix with cotton, while the new regenerated cellulose fibres that are now emerging are promising, but currently in short supply. Recycled polyester is meanwhile still based on petroleum resources which we want to move away from. As a consequence, there are only a few other options for us as a manufacturer and this new project will help us minimise our own waste while significantly lowering our carbon footprint.”

Other Monforts denim customers to introduce cotton fibre recycling operations at their plants recently include AGI Denim, Bossa and Soorty.

Vertical savings
Refresh is the name of the latest collection from AGI Denim – reflecting the company’s significant reduction in water consumption.

The company has just opened new fibre spinning and denim mills at its complex in Karachi, Pakistan.

“Over the years we’ve gone through a series of backward integration steps to become fully vertical,” said AGI Denim executive director Ahmed Javed, at Kingpins24 Flash. “In our latest expansion, we revisited every step of the production processes in order to make resource savings.”

Innovations have included the installation of proprietary robotics for garment finishing, but the most attention has been paid to water savings.

“Pakistan is one of the largest cotton-producing companies in the world and we’re fortunate that the type of cotton that is grown here is well suited to denim production and also helps us lower our carbon footprint, with everything done in close proximity,” Javed said. “In the lifecycle of a pair of denim jeans, however, cotton fibre production contributes 68% of water consumption. While we cannot control how much water cotton needs for it to grow, we can rethink the way we use it in our factory.”

Refresh-branded denims are washed from 100% recycled water as a result of the company’s new wastewater treatment plant, which puts production wastewater through a series of steps beginning with equalisation, followed by aeration and concluding with sedimentation. The water travels through filtration and ultrafiltration systems before being subjected to an activated carbon system and finally a reverse osmosis system to reduce any dissolved salts.

AGI now recycles 4.4 million gallons of water each month – enough to wash a million pairs of jeans.

Sustainable
Monforts has a leading position in the field of denim finishing with its well proven Thermex continuous dyeing systems, Montex stenter dryers and other lines for resource-efficient and economical processing.

“Our denim partners are constantly setting themselves new goals in respect of sustainable production – and more importantly, achieving them,” says Hans Wroblowski, Monforts Head of Denim. “We work closely with them with the aim of constantly optimising processing parameters and achieving further savings in energy, water and raw materials throughout the dyeing and finishing stages of production.”

The latest Monforts innovation for denim is the CYD yarn dyeing system. This technology is based on the effective and established dyeing process for denim fabrics that is now being applied for yarn dyeing. The CYD system integrates new functions and processes into the weaving preparation processes to increase quality, flexibility, economic viability and productivity. A full CYD line is now available for trials at the company’s Advanced Technology Centre in Mönchengladbach, Germany.”

The Montex®Coat ticks all the right boxes for coating success in 2021 (c) Monforts
A recent Montex®Coat installation at a European mill.
24.02.2021

The Montex®Coat ticks all the right boxes for coating success in 2021

Flexibility, product uniformity and automation are the keys to success for coating businesses in today’s rapidly-changing technical textiles industry, explained Jürgen Hanel, Monforts Head of Technical Textiles, at the recent 1st World Congress on Textile Coating.

Introducing the latest Montex®Coat magnetic roller coating option to virtual delegates from around the world at the conference organised by International Newsletters, Hanel explained why this technology makes perfect sense now

“The magnetic roller system allows a wide range of coatings and finishes to be carried out, while being easy to handle for operators and much easier to clean at the end of the process,” he said. “It provides textile finishers with an expanded range of options due to the fully-adjustable positioning of the magnet within the roller and with four different magnet positions possible, can be set to operate both as a direct coating system and as an indirect coater.”

Flexibility, product uniformity and automation are the keys to success for coating businesses in today’s rapidly-changing technical textiles industry, explained Jürgen Hanel, Monforts Head of Technical Textiles, at the recent 1st World Congress on Textile Coating.

Introducing the latest Montex®Coat magnetic roller coating option to virtual delegates from around the world at the conference organised by International Newsletters, Hanel explained why this technology makes perfect sense now

“The magnetic roller system allows a wide range of coatings and finishes to be carried out, while being easy to handle for operators and much easier to clean at the end of the process,” he said. “It provides textile finishers with an expanded range of options due to the fully-adjustable positioning of the magnet within the roller and with four different magnet positions possible, can be set to operate both as a direct coating system and as an indirect coater.”

With traditional dip coating systems, he added, as well as with many standard knife coating technologies, there is always a difference in the tension between the centre and the edges of the wide width fabrics being treated – and hence the amount of pressure with which the coating is applied. With the use of a magnetic roller, equal pressure is applied across the full width of the fabric, with consistent results even at wide widths of over 2.4 metres. In addition, adjusting the roller surface, rather than changing the coating formulation to match the required add-on and viscosity for each coating effect required, leads to much higher output from the line.

Cleaner and less wasteful
The contribution of such flexible and resource-saving new technologies to a cleaner and less wasteful textile industry was a key theme at the congress – held virtually across the four afternoons of February 11th, 12th, 18th and 19th – as was digitalization and the many advantages it is providing.

“A typical integrated Monforts coating line is automated from the inlet feed to the winder,” Hanel told delegates. “Adjustments can also be made simply and easily from the touchscreen and with the new hand-held remote controller which has recently been introduced for the Montex®Coat unit.”

Manual adjustment, he added, is time consuming and needs the attention of an experienced operator or the reproducibility will not be accurate between coating operations. The adjustment by motors allows each coating to be stored and downloaded again for 100% reproducibility.

The motors can be fully controlled from the touchscreen and all necessary adjustments carried out remotely, making switching from one process to another extremely quick and easy.
The accuracy that is now being demanded by today’s most exacting customers is met with an optional carbon fibre roller – especially in dealing with the winding tension required in the processing of materials such as prepregs for composites and other heavyweight fabrics. Typical applications for the Montex®Coat include the finishing of tents and awnings, black-out roller blinds and sail cloth, automotive interior fabrics and medical disposables. Full PVC coatings, pigment dyeing or minimal application surface and low penetration treatments can all be accommodated.

“The World Congress on Textile Coating was characterised by some very stimulating presentations and forums between the speakers and a global audience of textile specialists,” Jürgen Hanel concluded. “It truly reflected the high level of positive changes now taking place in not just textile coating, but the entire textile industry. I look forward to the next edition, which hopefully will be a face-to-face event for even deeper level discussions and debate.”

Monforts texCoat coating system (c) Monforts / AWOL Media
06.10.2020

Monforts at Innovate Textile & Apparel (ITA) 2020

During the Innovate Textile & Apparel (ITA) virtual textile machinery show which will run from October 15th-30th 2020, Monforts will be emphasising its leadership position in three key fields – advanced coating, denim finishing and fabric sanforizing.

With its multi-head capability, the latest Monforts texCoat coating system provides flexibility with an unprecedented range of options and a wide range of modules available.

Refinements
“Since we acquired the coating technology that our systems are based on we have made a lot of refinements and all of them are reflected in higher coating accuracy and the resulting quality of the treated fabrics,” says Monforts Head of Technical Textiles, Jürgen Hanel.
“Our systems have the shortest fabric path from the coating unit into the stenter and we have all variations of coating application systems too – and all of these options are available in wider widths, with the engineering and manufacturing from a single source here in Europe.”

During the Innovate Textile & Apparel (ITA) virtual textile machinery show which will run from October 15th-30th 2020, Monforts will be emphasising its leadership position in three key fields – advanced coating, denim finishing and fabric sanforizing.

With its multi-head capability, the latest Monforts texCoat coating system provides flexibility with an unprecedented range of options and a wide range of modules available.

Refinements
“Since we acquired the coating technology that our systems are based on we have made a lot of refinements and all of them are reflected in higher coating accuracy and the resulting quality of the treated fabrics,” says Monforts Head of Technical Textiles, Jürgen Hanel.
“Our systems have the shortest fabric path from the coating unit into the stenter and we have all variations of coating application systems too – and all of these options are available in wider widths, with the engineering and manufacturing from a single source here in Europe.”

CYD
Denim finishing is meanwhile a field in which Monforts has an undisputed lead and it has been working closely with its many partners in the key denim manufacturing countries of Bangladesh, Brazil, China, India, Mexico Pakistan and Turkey to develop advanced solutions. The latest of these is the CYD yarn dyeing system.
“CYD is based on the proven Econtrol® dyeing system for fabrics*,” explains Monforts Head of Denim Hans Wroblowski. “It integrates new functions and processes into the weaving preparatory processes – spinning, direct beaming, warping and assembly beaming, followed by sizing and dyeing – in order to increase quality, flexibility, economic viability and productivity. The CYD system has been developed in response to a very strong market demand.”

Pre-shrinking
Monforts has also recently delivered a significant number of its latest Monfortex sanforizing lines to customers around the world.
Sanforizing is vital to final fabric quality, pre-shrinking it by compressing prior to washing, to limit any residual or further shrinkage in a made-up finished garment to less than 1%, for perfect comfort and fit over an extended lifetime.

As with industry-leading Montex stenters, Monfortex lines benefit from the latest Qualitex 800 control system which allows all parameters to be easily automated via the 24-inch colour touchscreen, including production speed, control of all fabric feed devices, rotation spray or steaming cylinder options, the width of the stretching field and the rubber belt pressure. Up to 10,000 separate process parameter records can be generated and stored by the data manager.

 

*Econtrol® is a registered mark of DyStar Colours Distribution GmbH, Germany.

Coating expertise brings sustainable comfort and convenience to the face mask (c) A. Monforts Textilmaschinen GmbH & Co. KG
The masks are based on 100% woven cotton and the active ingredients in the finish are a reaction mass of titanium dioxide and silver chloride
21.09.2020

Coating expertise brings sustainable comfort and convenience to the face mask

  • Gorilla Protect is a new company formed in May this year to promote the Catus face mask – a major leap forward in the effectiveness of personal protection products that are available to consumers in the fight against Covid-19.
  • Behind Catus and the new company is Nova Textil, the established fabric finishing company based in Grefrath, Germany, and now run by father and son team Rainer and Oliver Hurtz.

Single stenter

Rainer Hurtz founded Nova Textil with a single Monforts Montex stenter and just five employees in 1999 and has steered its constant development and growth over the past twenty years.

“Our initial focus was on the coating of mainly glass fibre fabrics, awnings and sun protection products for outdoor furnishings,” he said. “We had a great customer who was providing us with so many orders that by 2005 we took the decision to order a second Montex stenter, in a special configuration. This also allowed us to enter the market for blackout and digital printing fabrics. We’ve had a great ongoing relationship with Monforts from the beginning.”

  • Gorilla Protect is a new company formed in May this year to promote the Catus face mask – a major leap forward in the effectiveness of personal protection products that are available to consumers in the fight against Covid-19.
  • Behind Catus and the new company is Nova Textil, the established fabric finishing company based in Grefrath, Germany, and now run by father and son team Rainer and Oliver Hurtz.

Single stenter

Rainer Hurtz founded Nova Textil with a single Monforts Montex stenter and just five employees in 1999 and has steered its constant development and growth over the past twenty years.

“Our initial focus was on the coating of mainly glass fibre fabrics, awnings and sun protection products for outdoor furnishings,” he said. “We had a great customer who was providing us with so many orders that by 2005 we took the decision to order a second Montex stenter, in a special configuration. This also allowed us to enter the market for blackout and digital printing fabrics. We’ve had a great ongoing relationship with Monforts from the beginning.”

A third Montex stenter line was installed at the company’s Grefrath plant in 2015, by which time the company had grown to 40 people and a major new market had opened up in the supply of fabrics for promotional materials at exhibitions and trade shows.

“We had a fantastic two years in 2018 and 2019 and everything was going great for the first three months of this year, but in April it all came crashing down,” said Oliver Hurtz. “Coronavirus put an end to trade shows in 2020, which had a very serious impact on our business.”

At the same time, however, the company was exploring the potential of a new biocidal product from one of its chemicals suppliers which has both antiviral and antimicrobial properties.

Filtration

“We had already been producing coated fabrics for hot gas filtration and realised that in combination with this new microporous coating we had the basis for a very effective single-layer face mask,” Rainer said. “Achieving this with a single layer product rather than the usual three has resulted in a significant advance in comfort for the wearer and because the mask is able to disinfect itself and helps regulate humidity, it can be worn a number of times without needing to be washed, for greater convenience. It only needs to be washed when it gets dirty and can also be washed up to twenty times without losing its properties, which has to be preferable to single-use disposables.”

Catus face masks are based on 100% woven cotton and the active ingredients in the finish are a reaction mass of titanium dioxide and silver chloride certified to ISO 20743 for their antibacterial effect, and to ISO 18184 for their antiviral effect.

They are proven to  eliminate over  99.99% of the human coronavirus 229 E, with the multiplication of microorganisms such as germs and bacteria prevented by the biostatic action of silver salts and viruses destroyed by oxygen-releasing substances and a mechanism that attacks their fatty envelope. The virus membrane loses its cholesterol content and the virus is inactivated.

Colours

Gorilla Protect next plans to make the masks available in four colours – black, Bordeaux, olive and grey – and is also working on colour branding and printing labels.

“It’s not possible to print on the surface of the mask after it has been coated, but its is possible for volume orders to be printed before the treatment,” Oliver Hurtz said.

“Face masks are going to become an established part of life in the West like they are in Asia and need to be as comfortable and convenient as possible for the wearer,” his father concluded. “With these things in mind, we believe Catus is a significant step forward.”

Acafintex looks to a bright future with new Monforts technology (c) AWOL Media
Acafintex father and son ownership team Don Francisco and Lic Francisco Moyano at the new Monforts installation.
14.09.2020

Acafintex looks to a bright future with new Monforts technology

At a total length of over 71 metres, the Montex finishing line that has just been installed by Monforts for Acafintex at its plant in Puebla, Mexico, is one of the highest capacity stenters the German technology leader has delivered to date.

Puebla is known as the epicentre of Mexico’s textile and clothing industry and is ideally placed for supplying both the USA and Europe, being three hours from the Gulf of Mexico for shipping via the Atlantic, and five hours from the Pacific coast as well.

Mexico's textile and clothing industry spans the entire production chain – from cotton growing and man-made fibre production to the manufacture of yarn, fabric, finished clothing and accessories. The industry is estimated to directly employ around 640,000 workers and to provide livelihoods for many more people indirectly. The country is a key supplier of textiles and clothing to the USA, but has faced fierce competition from China, which has until recently been the largest supplier of textiles and clothing to the US market.

At a total length of over 71 metres, the Montex finishing line that has just been installed by Monforts for Acafintex at its plant in Puebla, Mexico, is one of the highest capacity stenters the German technology leader has delivered to date.

Puebla is known as the epicentre of Mexico’s textile and clothing industry and is ideally placed for supplying both the USA and Europe, being three hours from the Gulf of Mexico for shipping via the Atlantic, and five hours from the Pacific coast as well.

Mexico's textile and clothing industry spans the entire production chain – from cotton growing and man-made fibre production to the manufacture of yarn, fabric, finished clothing and accessories. The industry is estimated to directly employ around 640,000 workers and to provide livelihoods for many more people indirectly. The country is a key supplier of textiles and clothing to the USA, but has faced fierce competition from China, which has until recently been the largest supplier of textiles and clothing to the US market.

However, the position of Mexico in the US import market has become more stable following the signing of the United States-Mexico-Canada Agreement (USMCA), which came into force in July this year. The country has also been a key beneficiary of the current trade war that is raging between China and the USA.

In addition, there is scope for higher sales in Mexico’s domestic market. The country has a population of 129 million people who are becoming increasingly prosperous, with a large proportion of younger people who are spending more on clothing.

Flexible operation

Founded in 1986, family-owned Acafintex operates as a commission dyehouse, finishing both knitted and woven fabrics for local companies in Mexico, in widths of between 100cm to 3.6 metres. The company is run by father and son team Don Francisco and Lic Francisco Moyano.

“We have very flexible operations for fabric finishing and also produce and sell our own fabrics for both the fashion industry and for the uniforms market,” says Don Francisco. “These days, we are increasingly finishing materials for technical textiles and for the automotive industry too. We have both local and international suppliers of both yarns and base fabrics and make sure we choose the best and most reliable sources. Exports now account for over 40% of our sales.”

European contract

With a  width of 3.8 metres, the new Monforts Montex line at Acafintex is equipped with no less than 12 double TwinAir drying chambers to meet the requirements of specific technical textiles to a European customer, in a contract secured following the company’s ISO 9001 certification in 2019. The line is equipped with an integrated heat recovery system and also benefits from an exhaust air cleaning system to ensure the most resource-efficient processing available on the market.

On the Monforts TwinAir system, the airflows above and below the fabric being dried can be regulated completely independently of each other, with Optiscan Auto-Balance fully controlling the distance between the fabric and the dryer nozzles via variable-frequency fan motors and CCD chip evaluation. As a result, the evaporation rate of the stenter and its energy utilisation are always fully optimised. Contact-free drying eliminates the possibility of fabric marking or stitch draft.

Highly-intuitive Monforts Qualitex visualisation software allows all machine functions and process parameters to be assessed and controlled easily, and thousands of article specific settings and formulations to be called up at any time – with 100% reproducible results.

In combination with an existing Montex stenter, the new line has expanded finishing capacity at Acafintex to an annual 20 million linear metres.

Modifications

“From the installation to the start-up, we were supported by a team of Monforts technicians and local representative Arnulf Thaler at Sattex here in Mexico,” says Lic Francisco. “Of course, every installation has its challenges and with such big machines we needed to modify several things inside the factory and also required certain modifications from Monforts which were all carried out successfully.”  

Forced, like much of the textile industry globally, to temporarily suspend operations at the height of the Covid-19 pandemic, Acafintex is now back to full production, having installed the necessary safety measures for its employees, and is anticipating a bright future.

“We are passionate about developing new materials in search of mutual benefit for both our clients and suppliers, as well as our own workforce and the environment,” Don Francisco Moyano concludes. “Investment in the latest technology like this new Monforts line plays a key role in helping us achieve our long-term goals.”

Sustainable leadership for GtA with new Monforts Montex wide width lines (c) AWOL Media
GtA Managing Director Andreas Niess
27.07.2020

Sustainable leadership for GtA with new Monforts Montex wide width lines

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

Following the successful commissioning of two new Monforts Montex wide-width stenter lines and additional environmental management equipment at its plant in Germany, GtA – Society for Textile Equipment GmbH – is aiming to be the first textile finishing company to become entirely CO2-neutral in the manufacture of all of its products by 2025.

GtA is a partner company to Germany’s large-format digital printing fabric leader, Georg and Otto Friedrich GmbH, which has has this year been able to considerably expand its portfolio due to the new Monforts lines.

Headquartered in Gross-Zimmern, close to Frankfurt, Georg and Otto Friedrich GmbH and its partners in Germany have an annual production of 37 million square metres of warp knits for a range of end-use applications, including garments, automotive interiors and technical textiles, but increasingly with a concentration on digital printing substrates.

Fault-free textiles

A new standard in pure white, 100% clean and fault-free textile substrates has been demanded by this market in recent years due to the rapid growth in digitally-printed banners and billboards – often referred to as ‘soft signage’.

The substrates of choice for digital printing are 100% polyester warp knits which are resilient and allow excellent take-up of inks, and vibrant colours and clear and precise images to be achieved with digital printing techniques. The knitted construction also has the advantage of elasticity, which is a plus in terms of flexibility for installers.

Critically, the warp knitted fabrics have extremely smooth surfaces which is becoming increasingly important due to the general move away from PVC coatings which were the standard in the past.

It was to finish these fabrics for Georg and Otto Friedrich GmbH as well as providing such services for many other customers, that the GtA plant in Neresheim, Baden-Württemberg, was established in 2015.

The purpose-built plant on a greenfield site was initially equipped with a fully-automated, 72 metre long Monforts installation comprising a washing machine integrated with a 3.6 metre wide, seven-chamber Montex stenter. The line quickly went from single to double shift production and then to 24/7 operation  to meet demand.

Expanded widths

Building on the success of this installation, GtA has now installed two more Montex stenter lines – both in expanded working widths of 5.6 metres and purpose-built at Montex GmbH in Austria.

A six-chamber Montex unit is combined with a washing machine to guarantee the purity of the substrates, while a five-chamber line is integrated with a wide-width coating machine. This new coating capability at GtA has led to a number of new additions to the Georg and Otto Friedrich DecoTex range for digital printing, including wide width fabrics with flame retardant, antimicrobial and non-slip finishes.

The new Montex stenter lines benefit from all of the latest innovations from Monforts, including the Smart Sensor system for the optimised maintenance planning of key mechanical wear components on the stenters. A comprehensive overview of the condition of all parts at any time is now available for operators within the highly intuitive Qualitex visualization software.

With Qualitex, all article-specific settings can be stored and the formulations for thousands of treatment processes called up again at any time. Individual operators can also personalise their dashboards with the most important machine functions and process parameters.

Environmental commitment

GtA is run by a seasoned team of textile professionals led by Managing Director Andreas Niess.

“We have received excellent service from Monforts from the outset and we were happy to place the order for these two new lines as part of our ongoing cooperation,” he says. “With all of the latest Monforts advances in technology we are fully in control of all production and quality parameters with these lines, as part of our significant commitment to innovative environmental technology.”

The GtA plant, which operates in near-cleanroom conditions, has also been equipped with proprietary technology to fully exploit the Monforts air-to-air heat recovery systems that are now standard with Montex stenters.

“Around 30 per cent of our investment volume at the site goes to energy-saving measures and we are sure that this commitment is worthwhile,” Mr Niess says. “As an example, our integrated heat recovery system fully exploits the waste heat from the process exhaust air and the burner exhaust gases of the Monforts stenters, allowing us to achieve an exhaust air temperature of  between 30 to 34°C, compared to what would conventionally be between 140 to 160°C. Another focus has been on exhaust air purification technology and here too, the latest technology has been installed with integrated heat recovery elements.”

This, he adds, saves 52% of the energy that would normally be used – equating to 5,800,000 KwH per year. The necessary audits for energy-efficient companies are also carried out annually.

In addition, GtA has purpose-designed the automatic chemical mixing and dosing systems that feed the padders for the key treatments that are carried out on the fabrics through the stenters.

The company is going further, however, in its pursuit of clean production and raw materials.

"We want to be an asset and not a burden on our immediate environment and therefore do not use any additives containing solvents," Mr Niess says. “We were the first to use fully halogen-free flame retardant chemistry, and we use bio-based, finely ground alumina products for the washing process instead of surfactants. PES polyester yarns made from recycled material are also increasingly used and the latest additions to our raw materials portfolio, the RC-Ocean products, are made from recycled sea plastic.

“We are now planning a combined heat and power plant for the production of electrical energy and heat and we will also build a photovoltaic system that converts solar radiation into electrical energy. GtA wants to be the first textile finishing company to be CO2-neutral in the manufacture of all of its products by 2025. The complete heat supply and heating for the 13,000 square metre production hall, as well as the office building and the hot water supply for the domestic water, is already energy-neutral. We are convinced that this commitment will pay off in the long term and our positive business development proves that sustainability and business profitability are perfectly compatible.”

In addition to the products for Georg and Otto Friedrich GmbH, GtA  offers its manufacturing capacities for other customers as a contract service.

All products are manufactured in accordance with Öko-Tex Standard 100, product class 1 and the company is also involved in the research and development of new sustainable manufacturing processes, in cooperation with many regional universities and funding project partners.

Quelle:

AWOL Media for A. Monforts Textilmaschinen GmbH & Co. KG

(c) A. Monforts Textilmaschinen GmbH & Co. KG
24.01.2020

Talking sustainability with Monforts denim customers

In the latest short film released on the Monforts YouTube Channel – captured at the recent Denim Première Vision show in London – some of the leading global manufacturers discuss their initiatives for more sustainable denim production.

Cone Denim, based in Greensboro, North Carolina, for example, can lay claim to having put in place its first environmental control measures back in the 1940s when the company first started recycling its water.

“It was a method of efficiency even back then, eighty years ago,” says Gabriel Magopat, of the company’s UK customer service centre, “but  producing high quality products is another method of being sustainable and of being efficient, and I think that’s what Cone stands for. We have an amazing history.”

Cone Denim is known for its signature S Gene® stretch denims which have traditionally incorporated polyester components to provide the stretch. It has now partnered with Intrinsic Advanced Materials of Gastonia, also in North Carolina, to introduce patent-pending CiCLO stretch polyester fibres into its denim collections. 

In the latest short film released on the Monforts YouTube Channel – captured at the recent Denim Première Vision show in London – some of the leading global manufacturers discuss their initiatives for more sustainable denim production.

Cone Denim, based in Greensboro, North Carolina, for example, can lay claim to having put in place its first environmental control measures back in the 1940s when the company first started recycling its water.

“It was a method of efficiency even back then, eighty years ago,” says Gabriel Magopat, of the company’s UK customer service centre, “but  producing high quality products is another method of being sustainable and of being efficient, and I think that’s what Cone stands for. We have an amazing history.”

Cone Denim is known for its signature S Gene® stretch denims which have traditionally incorporated polyester components to provide the stretch. It has now partnered with Intrinsic Advanced Materials of Gastonia, also in North Carolina, to introduce patent-pending CiCLO stretch polyester fibres into its denim collections. 

While still being synthetic based, CiCLO polyester is able to biodegrade in marine environments, wastewater treatment plants and landfill conditions, at rates similar to natural fibres like wool. 

This more sustainable solution for stretch is also being introduced to China for the first time by another leading denim supplier, Advance Denim.

“Advance Denim is spending its resources on being the most technologically advanced company in China, and also the most sustainable,” says Mark Ix, the company’s Director of Marketing. “We are investing heavily in our manufacturing to save both water and chemicals to create cleaner products.”

Monforts denim customer Berto is a family-owned company with its main denim mill in Bovolenta, a small rural town near to Padua in the north east of Italy, where respect for the environment has always been a must.

“The family has always been focused on respect for the environment,” says Berto’s Marketing Manager Francesca Palento. “In particular, we have a river next to the company from which we take our water for production and we then return it cleaner than it was before. We are also now producing GOTS and Global Recycling Standard jean produced with yarns made from our own internal waste production.”

Pakistan’s Soorty has recently received Cradle to Cradle Gold certification – the most stringent and exacting sustainable standard currently in existence – for its Pure D range of denims. These are produced using the company’s proprietary Zero Waste Water dyeing technology, in combination with the most advanced Monforts finishing machines. 

“Our very latest collection is called Climate Jeans, because every single product we now produce draws attention to the climate emergency we are living through right now,” says Eda Dikman, Soorty’s Marketing Communications Manager. “Sustainability is very important to us because we produce at scale and all of the actions we take reflect on the planet.”

Monforts: Half a century of excellence (c) A. Monforts Textilmaschinen GmbH & Co. KG
Monforts: Half a century of excellence
20.01.2020

Monforts: Half a century of excellence

The origins of both Industry 4.0 and an awareness of the need for more sustainable manufacturing methods can arguably be traced back to the year 1971.

It was in 1971 that the first microprocessor was introduced by Intel, and also that the first and perhaps now most well-known environmental campaigner, Greenpeace, was founded.

As such, a direct line can be charted from that year to today’s automated textile manufacturing machinery concepts, as well as the drive to develop more increasingly resource-efficient processes.

All of the recent innovations which have been introduced to the market by A. Monforts Textilmaschinen GmbH & Co. KG, for example, are being powered by the possibilities of Industry 4.0 and developed in response to the market demand for more sustainable production.

The origins of both Industry 4.0 and an awareness of the need for more sustainable manufacturing methods can arguably be traced back to the year 1971.

It was in 1971 that the first microprocessor was introduced by Intel, and also that the first and perhaps now most well-known environmental campaigner, Greenpeace, was founded.

As such, a direct line can be charted from that year to today’s automated textile manufacturing machinery concepts, as well as the drive to develop more increasingly resource-efficient processes.

All of the recent innovations which have been introduced to the market by A. Monforts Textilmaschinen GmbH & Co. KG, for example, are being powered by the possibilities of Industry 4.0 and developed in response to the market demand for more sustainable production.

They include the new ‘digital twinning’ capability introduced in 2019 for all Monforts machines, with advanced sensor technologies which make it possible to access comprehensive technical machine data from any location using the company’s Smart Support and Smart Check apps. In addition, the digital twin system provides information on individual wear parts, such as, for example, converters or gears.

These latest developments have been very favourably received by Monforts customers, especially in Europe.

50th anniversary
The very first Heimtextil – the leading trade fair for the home textiles market – was also held in Frankfurt in January 1971 and Monforts customers Bierbaum Group and Konrad Hornschuch AG are amongst the German companies who were there from the very start and have attended every annual show since.

Bierbaum Group, based in Borken, is the company behind the well-known Irisette bedding brand and is celebrating its own 125th anniversary in 2020. It has also introduced products bearing the German government’s new Grüner Knopf textile seal of approval for sustainable production.

As a specialist in synthetic leathers for home surfaces, as well as vehicle interiors, Konrad Hornschuch AG, of Weissbach, has been a member of the €44 billion automotive giant Continental AG since 2016.

Representatives from both companies received memorial trophies at a special presentation held on January 7th during the 50th anniversary Heimtextil show.

The home textiles market remains very strong in Germany, with sales amounting to some €9.6 billion in 2019, according to analyst IFH Cologne.

Global growth
The first Heimtextil in 1971 was a significant success, attracting 679 exhibitors from 26 countries.

This year’s show, however, attracted a total of 2,952 exhibitors from 66 countries, reflecting not only the growth of the home textiles industry, but also the globalisation which has taken place over the last half century.

Monforts now has customers for its advanced finishing technologies around the world, with home textile customers from India and Pakistan being particularly well represented at Heimtextil 2020.

Among stand outs from Indian companies at this year’s show was the 2020 collection of Welspun India’s famous Christy England brand, inspired by botanical studies of the gardens of British stately homes. Welspun towels meanwhile benefit from the company’s HygroCotton hollow core yarn technology, produced by a proprietary spinning method which ensures they become softer, fluffier and more absorbent after every wash.

An equally ground-breaking new technology is being introduced by Trident Group, which is one of India’s largest vertically-integrated home textiles manufacturers and two years ago installed five complete Monforts finishing ranges for its new linen department.

Trident’s patented Air Rich yarns feature pores throughout their cross sections for high breathability and absorbency, as well as rapid drying.

Monforts home textile customers from Pakistan stressed the resource efficiency of their processes and products as a result of investments in advanced technology, and during the show the ‘Sustainable Pakistan’ initiative was announced.

Supported by GIZ, the German Society for International Cooperation, the initiative aims to reshape global perceptions of Pakistan’s manufacturers and their innovations. So far, twenty producers have been carefully chosen to be presented on this global platform and will help rebrand Pakistan’s textile industry at the Heimtextil exhibitions going forward.

Heimtextil’s organiser Messe Frankfurt also announced its own new alliance with the United Nations Office for Partnerships, in order to support the UN’s Sustainable Development Goals.

Constancy
Many things have changed since 1971 and home interiors are certainly no longer predominantly orange and brown – and perhaps unlikely to ever become so again.

It’s clear, however, that there has been a constancy in the push to consistently improve textile technologies, processes and products that may have originated in Europe, but have subsequently spread around the world.

And the significance of both microprocessors and sustainability in 2020 could only have been guessed at back in 1971.

 

Monforts (c) A. Monforts Textilmaschinen GmbH & Co. KG
02.09.2019

Monforts: Responding to China’s requirements in 2019

It’s well-known that the astonishing success of China’s economy over the past decade has sent wages soaring and made it difficult for the country’s textile manufacturers to find and retain trained machine operators, while operating in a highly competitive market where optimised production and full resource efficiency are of paramount importance.

In direct response to this situation, A. Monforts Textilmaschinen GmbH & Co. KG has introduced a range of new Industry 4.0 technologies aimed at simplifying machine operation while providing easy access to all data and instant or remote assistance.

At the forthcoming Shanghaitex 2019 textile machinery exhibition, which takes place from November 25-28 in Shanghai, Monforts specialists will be at stand A10 in Hall W and look forward to discussing the company’s latest developments in this area with valued Chinese customers.

They include the latest Qualitex full touch panel control system, with its digital twinning capability and Smart Check and Smart Support apps, reinforced by the comprehensive Monforts Smart Sensor machine monitoring programme.

It’s well-known that the astonishing success of China’s economy over the past decade has sent wages soaring and made it difficult for the country’s textile manufacturers to find and retain trained machine operators, while operating in a highly competitive market where optimised production and full resource efficiency are of paramount importance.

In direct response to this situation, A. Monforts Textilmaschinen GmbH & Co. KG has introduced a range of new Industry 4.0 technologies aimed at simplifying machine operation while providing easy access to all data and instant or remote assistance.

At the forthcoming Shanghaitex 2019 textile machinery exhibition, which takes place from November 25-28 in Shanghai, Monforts specialists will be at stand A10 in Hall W and look forward to discussing the company’s latest developments in this area with valued Chinese customers.

They include the latest Qualitex full touch panel control system, with its digital twinning capability and Smart Check and Smart Support apps, reinforced by the comprehensive Monforts Smart Sensor machine monitoring programme.