Aus der Branche

Zurücksetzen
16 Ergebnisse
03.11.2022

SGL Carbon: Positive Geschäftsentwicklung in allen Geschäftsbereichen

  • Positive Geschäftsentwicklung in allen vier Geschäftsbereichen
  • Umsatzanstieg um 14,8 % auf 853,9 Mio. €
  • Bereinigtes EBITDA verbessert sich um 25,4 % auf 136,1 Mio. €
  • Erfolgreiche Refinanzierung der Wandelschuldverschreibung von 2018

Nach 270,9 Mio. € im 1. Quartal 2022 und 278,9 Mio. € im 2. Quartal erhöhte die SGL Carbon den Konzernumsatz im 3. Quartal 2022 auf 304,1 Mio. €. Nach neun Monaten entspricht dies einem deutlichen Umsatzwachstum von 14,8 % auf insgesamt 853,9 Mio. € (9M 2021: 743,5 Mio. €). Die erfreuliche Geschäftsentwicklung spiegelt sich auch im bereinigten EBITDA der Gesellschaft wider, das sich im Vergleich zum Vorjahreszeitraum um 25,4 % auf 136,1 Mio. € verbesserte (9M 2021: 108,5 Mio. €). Zum operativen Erfolg haben alle vier Geschäftsbereiche beigetragen.

Ausblick
Aufgrund der positiven Geschäftsentwicklung hat das Management die Prognose für das Gesamtjahr am 6. September 2022 erhöht. Für das Geschäftsjahr 2022 wird ein Konzernumsatz von ca. 1,2 Mrd. € (zuvor: ca. 1,1 Mrd. €) und ein bereinigtes EBITDA von 170 bis 190 Mio. € (zuvor: 130 bis 150 Mio. €) erwartet.

  • Positive Geschäftsentwicklung in allen vier Geschäftsbereichen
  • Umsatzanstieg um 14,8 % auf 853,9 Mio. €
  • Bereinigtes EBITDA verbessert sich um 25,4 % auf 136,1 Mio. €
  • Erfolgreiche Refinanzierung der Wandelschuldverschreibung von 2018

Nach 270,9 Mio. € im 1. Quartal 2022 und 278,9 Mio. € im 2. Quartal erhöhte die SGL Carbon den Konzernumsatz im 3. Quartal 2022 auf 304,1 Mio. €. Nach neun Monaten entspricht dies einem deutlichen Umsatzwachstum von 14,8 % auf insgesamt 853,9 Mio. € (9M 2021: 743,5 Mio. €). Die erfreuliche Geschäftsentwicklung spiegelt sich auch im bereinigten EBITDA der Gesellschaft wider, das sich im Vergleich zum Vorjahreszeitraum um 25,4 % auf 136,1 Mio. € verbesserte (9M 2021: 108,5 Mio. €). Zum operativen Erfolg haben alle vier Geschäftsbereiche beigetragen.

Ausblick
Aufgrund der positiven Geschäftsentwicklung hat das Management die Prognose für das Gesamtjahr am 6. September 2022 erhöht. Für das Geschäftsjahr 2022 wird ein Konzernumsatz von ca. 1,2 Mrd. € (zuvor: ca. 1,1 Mrd. €) und ein bereinigtes EBITDA von 170 bis 190 Mio. € (zuvor: 130 bis 150 Mio. €) erwartet.

Folglich wird ein bereinigtes EBIT von 110 bis 130 Mio. € (zuvor: 70 bis 90 Mio. €) prognostiziert. Die Erwartungen zur Kapitalrendite (ROCE) von ursprünglich 7 % bis 9 % werden entsprechend der Ergebnisentwicklung auf 10 % bis 12 % angehoben. Die Einschätzung zum Free Cashflow (deutliche Unterschreitung des Vorjahresniveaus von 111,5 Mio. €) bleibt unverändert.

Quelle:

SGL CARBON SE

(c) BRÜCKNER
Das Projektteam von BRÜCKNER und HEATHCOAT im Leonberger Technologiezentrum
04.10.2022

BRÜCKNER: Neue Anlage für britisches Unternehmen HEATHCOAT FABRICS

Der deutsche Hersteller von Textilveredlungsanlagen BRÜCKNER liefert zum wiederholten Male eine Anlage an HEATHCOAT FABRICS. HEATHCOAT FABRICS ist auf die Herstellung von technischen Textilien in den Bereichen Texturierung, Weberei und Wirkerei sowie Färberei und Ausrüstung spezialisiert. Die Produkte des britischen Textilherstellers werden unter anderem für die Automobil-, Gesundheits-, Verteidigungs- und Luftfahrtindustrie hergestellt.

Der deutsche Hersteller von Textilveredlungsanlagen BRÜCKNER liefert zum wiederholten Male eine Anlage an HEATHCOAT FABRICS. HEATHCOAT FABRICS ist auf die Herstellung von technischen Textilien in den Bereichen Texturierung, Weberei und Wirkerei sowie Färberei und Ausrüstung spezialisiert. Die Produkte des britischen Textilherstellers werden unter anderem für die Automobil-, Gesundheits-, Verteidigungs- und Luftfahrtindustrie hergestellt.

Regina Brückner, Geschäftsführerin und Inhaberin der BRÜCKNER Gruppe, erklärt: „Die komplexen Anforderungen von HEATHCOAT zu erfüllen ist nicht einfach, da die Vielfalt der hergestellten technischen Textilien sehr groß ist. Unsere Anlage muss leichte wie schwere Artikel veredeln. Die Auslegung, Steuerung und das gesamte Anlagenlayout müssen daher flexibel, funktional und trotzdem einfach zu bedienen sein. Glücklicherweise ist das Team von HEATHCOAT FABRICS sehr innovativ und aufgeschlossen. Gemeinsam haben wir in intensiver Zusammenarbeit die richtige Technologie und Handhabung entwickelt. Wir sind sehr glücklich, dass wir diesen von uns sehr geschätzten Kunden mit der Produktivität unserer Anlage und natürlich mit unserem technologischen Know-how überzeugen konnten.“

Die BRÜCKNER POWER-FRAME Spannmaschine mit direkter Gasheizung und gekonterten Thermozonen sorgt für gleichmäßige Temperaturen über die gesamte Länge und Breite des Trockners. Die Anlage ist mit einer schmierungsarmen, horizontal umlaufenden Nadel-Kluppen-Kombikette ausgestattet und ermöglicht mehrere Warenläufe, die speziell auf die zu verarbeitenden Gewebe abgestimmt sind. Zudem wurde gemeinsam mit HEATHCOAT FABRICS ein spezieller Auslauf mit unterschiedlichen Möglichkeiten für Kanten- und Mittenschnitt entwickelt. Je nach Art der Produkte kann die Ware auf Großdocken oder Papphülsen gewickelt oder auf Wagen abgetafelt werden.

Quelle:

Brückner Trockentechnik GmbH & Co. KG

(c) AkzoNobel
12.07.2022

AkzoNobel announces €20 million investment and creates new jobs in France

A €20 million investment has been announced by AkzoNobel to increase and improve production at two of its sites in France. Around 30 new jobs will be created.

A total of €15 million will be spent on the company’s aerospace coatings facility in Pamiers, which was taken over following the Mapaero acquisition in 2019. Production capacity is being boosted by 50%, while the funds will also be used to reduce environmental impact and improve safety processes and working conditions.

The other €5 million will be spent on improving production flexibility at the decorative paints site in Montataire, which is one of the company’s most important manufacturing locations for wall paints in Europe.

The plans for Pamiers include the construction of two extensions, one for storage and one for cleaning and waste treatment. The project will also enable the company to relocate the production of exterior polyurethane paints for aircraft widely used in Europe from its Waukegan plant in the US.

Building work is expected to start by the end of 2023, with the new installations at both locations due to be operational in early 2025.

A €20 million investment has been announced by AkzoNobel to increase and improve production at two of its sites in France. Around 30 new jobs will be created.

A total of €15 million will be spent on the company’s aerospace coatings facility in Pamiers, which was taken over following the Mapaero acquisition in 2019. Production capacity is being boosted by 50%, while the funds will also be used to reduce environmental impact and improve safety processes and working conditions.

The other €5 million will be spent on improving production flexibility at the decorative paints site in Montataire, which is one of the company’s most important manufacturing locations for wall paints in Europe.

The plans for Pamiers include the construction of two extensions, one for storage and one for cleaning and waste treatment. The project will also enable the company to relocate the production of exterior polyurethane paints for aircraft widely used in Europe from its Waukegan plant in the US.

Building work is expected to start by the end of 2023, with the new installations at both locations due to be operational in early 2025.

AkzoNobel employs nearly 1,500 people in France and operates four production facilities, in Montataire (decorative paints), Dourdan (powder coatings), Limoges (adhesive markings) and Pamiers (aerospace coatings).

Weitere Informationen:
AkzoNobel Coatings aerospace
Quelle:

AkzoNobel

(c) COBRA International
12.04.2022

COBRA International showcases its portfolio for vehicle systems at AUVSI XPONENTIAL 2022

Cobra International will showcase its portfolio of design and manufacturing solutions for the unmanned vehicle systems sector when the company exhibits alongside long-term partner HiveGround at the AUVSI XPONENTIAL 2022 conference.

Taking centre stage on the Cobra stand will be a fully assembled Swiftlet UAV. This compact tactical fixed wing UAV platform has a 5.5m wingspan and was developed by the Royal Thai Air Force and National Science and Technology Development Agency (NSTDA) for a broad range of survey, monitoring and search and rescue (SAR) operations. Cobra manufactured the 30kg Swiftlet composite airframe using a combination of CNC cut carbon sandwich internal structure and PVC foam sandwich skins using both high grade glass fibre and carbon fibre reinforcements.

Visitors to the Cobra stand will also see the VETAL, a twin rotor vertical take-off and landing (VTOL) drone with a composite airframe manufactured by Cobra for HiveGround, the Thailand based developer of UAV surveying and robotics systems.

Cobra International will showcase its portfolio of design and manufacturing solutions for the unmanned vehicle systems sector when the company exhibits alongside long-term partner HiveGround at the AUVSI XPONENTIAL 2022 conference.

Taking centre stage on the Cobra stand will be a fully assembled Swiftlet UAV. This compact tactical fixed wing UAV platform has a 5.5m wingspan and was developed by the Royal Thai Air Force and National Science and Technology Development Agency (NSTDA) for a broad range of survey, monitoring and search and rescue (SAR) operations. Cobra manufactured the 30kg Swiftlet composite airframe using a combination of CNC cut carbon sandwich internal structure and PVC foam sandwich skins using both high grade glass fibre and carbon fibre reinforcements.

Visitors to the Cobra stand will also see the VETAL, a twin rotor vertical take-off and landing (VTOL) drone with a composite airframe manufactured by Cobra for HiveGround, the Thailand based developer of UAV surveying and robotics systems.

At AUVSI XPONENTIAL, Cobra will also illustrate how the company leverages innovation and expertise developed in its water sports and automotive business to enhance its product offering to the UAV sector. Products on display include a Fliteboard electric foiling surfboard, pre-preg hydrofoil parts, lightweight medical prosthetics, flax and forged carbon parts, as well as a full set of visual carbon and painted automotive trims, each demonstrating the company’s high volume production capacity for ultra-light carbon composite structures.

The show will take place from the 25 to 28 April at the Orange County Convention Center, Orlando, Florida.

Quelle:

COBRA International / 100% Marketing

Expansion begins at Hexcel Engineered Core Operations Plant in Morocco (c) Hexcel Corporation
15.03.2022

Expansion begins at Hexcel Engineered Core Operations Plant in Morocco

Hexcel Corporation hosted customers and public officials at its manufacturing site in the Midparc Free Trade Zone in Casablanca as the company broke ground on an expansion that will double the size of its existing engineered core manufacturing operation in Morocco to meet increased demand from aerospace customers for lightweight advanced composites.

The expansion, announced in September 2021, is expected to be completed in early 2023. The plant size will double to 24,000 square meters and employment is expected to increase from 120 to 400 people when the expansion is completed.

The Casablanca facility was built as part of Hexcel’s ongoing worldwide investment to create a diversified and robust global supply chain to support aerospace customers’ growing demand for engineered core. At the plant, Hexcel transforms lightweight honeycomb materials into engineered core parts to reinforce structures in the aerospace industry, particularly for aircraft, engine nacelles, and helicopter blades.

Hexcel Corporation hosted customers and public officials at its manufacturing site in the Midparc Free Trade Zone in Casablanca as the company broke ground on an expansion that will double the size of its existing engineered core manufacturing operation in Morocco to meet increased demand from aerospace customers for lightweight advanced composites.

The expansion, announced in September 2021, is expected to be completed in early 2023. The plant size will double to 24,000 square meters and employment is expected to increase from 120 to 400 people when the expansion is completed.

The Casablanca facility was built as part of Hexcel’s ongoing worldwide investment to create a diversified and robust global supply chain to support aerospace customers’ growing demand for engineered core. At the plant, Hexcel transforms lightweight honeycomb materials into engineered core parts to reinforce structures in the aerospace industry, particularly for aircraft, engine nacelles, and helicopter blades.

At the event, Thierry Merlot, Hexcel President – Aerospace for Europe, MEA/AP & Industrial, said, “We are pleased to celebrate this milestone with our customers and with the local community. The increased demand for lightweight, aerodynamic, advanced composites is growing, and our customers including Safran, Airbus, Airbus Atlantic, Boeing and Spirit AeroSystems have shown confidence in our ability to meet that demand. We appreciate the support from them as well as from the Ministry and everyone in the local community who continue providing us with the opportunity to further our investment in Morocco. The very successful establishment of Hexcel, the qualification of the workforce, the support of the state and the proximity of our customers have been real assets to launch this extension of our site in Casablanca.”

Quelle:

Hexcel Corporation

03.02.2022

The 2022 JEC Composites Innovation Awards: Official Finalists line up

Première Vision - Each year, since its creation more than 20 years ago, the JEC Composites Innovation Awards celebrate successful projects and cooperation between players of the composite industry.
The competition has especially shined a light on some 203 companies and 499 partners, awarding them for the excellence of their composite innovations.

After pre-selection of the finalists, one winner is selected in each category:

  • Aerospace – Application
  • Aerospace – Process
  • Automotive & road transportation – surface
  • Automotive & road transportation – structural
  • Building & Civil Engineering
  • Design, Furniture & Home
  • Equipment & Machinery
  • Maritime Transportation & Shipbuilding
  • Sports, Leisure & Recreation
  • Renewable Energy

The international jury representing the entire composites value chain includes:

Première Vision - Each year, since its creation more than 20 years ago, the JEC Composites Innovation Awards celebrate successful projects and cooperation between players of the composite industry.
The competition has especially shined a light on some 203 companies and 499 partners, awarding them for the excellence of their composite innovations.

After pre-selection of the finalists, one winner is selected in each category:

  • Aerospace – Application
  • Aerospace – Process
  • Automotive & road transportation – surface
  • Automotive & road transportation – structural
  • Building & Civil Engineering
  • Design, Furniture & Home
  • Equipment & Machinery
  • Maritime Transportation & Shipbuilding
  • Sports, Leisure & Recreation
  • Renewable Energy

The international jury representing the entire composites value chain includes:

  • Michel COGNET, Chairman of the Board, JEC Group
  • Christophe BINETRUY, Professor of Mechanical Engineering, EC Nantes
  • Kiyoshi UZAWA, Professor/Director, Innovative Composite Center, Kanazawa Institute of Technology
  • Jiming Sung HA, Professor, Hanyang University
  • Brian KRULL, Global Director of Innovation, Magna Exteriors Inc
  • Karl-Heinz FULLER, Manager Future Outside Materials, Mercedes Benz AG
  • Deniz KORKMAZ, CTO, Kordsa Teknik Tekstil AS
  • Henry SHIN, Head of Center, K-CARBON
  • Véronique MICHAUD, Associate Professor/ Director, EPFL – Laboratory for Processing of Advanced Composites
  • Alan BANKS, Lightweight Innovations Manager, Ford Motor Company
  • Enzo CRESCENTI, Technical Authority and Composite Expert, Airbus

Discover the finalists in each category here.

Quelle:

JEC Group

Mit dem Shirt „SmartTex“ können Astronautinnen und Astronauten die nötigen Sensoren komfortabel am Körper tragen. © DLR
SmartTex Shirt
27.10.2021

Forschung für kosmische Missionen: SmartTex liefert Daten über Vitalfunktionen

Es sieht aus wie ein normales Shirt, doch es hat es in sich:  Das neue SmartTex Shirt transferiert mittels integrierter Sensoren physiologische Daten von Astronautinnen und Astronauten über ein drahtloses Kommunikationsnetzwerk zur Erde.  Auf diese Weise sollen die Auswirkungen der Weltraumumgebung auf das menschliche Herz-Kreislauf-System, vor allem in Hinblick auf langfristige bemannte Weltraum-Missionen, bewertet und dokumentiert werden. Getestet wird das vom Deutschen Zentrum für Luft- und Raumfahrt (DLR) in Kooperation mit der DSI Aerospace Technology, der Medizinischen Fakultät der Universität Bielefeld sowie dem textilen Forschungspartner Hohenstein entwickelte SmartTex im Rahmen des Projekts Wireless Compose-2 (WICO2) zum ersten Mal vom deutschen ESA-Astronauten Dr. Matthias Maurer, der am 30. Oktober 2021 für sechs Monate zu seiner Mission Cosmic Kiss auf der Internationalen Raumstation ISS aufbricht.

Es sieht aus wie ein normales Shirt, doch es hat es in sich:  Das neue SmartTex Shirt transferiert mittels integrierter Sensoren physiologische Daten von Astronautinnen und Astronauten über ein drahtloses Kommunikationsnetzwerk zur Erde.  Auf diese Weise sollen die Auswirkungen der Weltraumumgebung auf das menschliche Herz-Kreislauf-System, vor allem in Hinblick auf langfristige bemannte Weltraum-Missionen, bewertet und dokumentiert werden. Getestet wird das vom Deutschen Zentrum für Luft- und Raumfahrt (DLR) in Kooperation mit der DSI Aerospace Technology, der Medizinischen Fakultät der Universität Bielefeld sowie dem textilen Forschungspartner Hohenstein entwickelte SmartTex im Rahmen des Projekts Wireless Compose-2 (WICO2) zum ersten Mal vom deutschen ESA-Astronauten Dr. Matthias Maurer, der am 30. Oktober 2021 für sechs Monate zu seiner Mission Cosmic Kiss auf der Internationalen Raumstation ISS aufbricht.

„Schon bei den Vorgängerprojekten Spacetex (2014) und Spacetex2 (2018) konnten wir wertvolle Einblicke in das Zusammenwirken von Körper, Bekleidung und Klima unter Schwerelosigkeit gewinnen.“, erklärt Hohenstein Senior Scientific Expert Dr. Jan Beringer. Die damals durch den Einsatz des ESA-Astronauten Dr. Alexander Gerst gelieferten Erkenntnisse flossen nun unmittelbar in die Entwicklung des neuen SmartTex Shirts bei Hohenstein mit ein. „Matthias Maurer kann sein maßgeschneidertes Shirt während der (all)täglichen Arbeit auf der Internationalen Raumstation komfortabel am Körper tragen. Dafür haben wir seine Körpermaße als Grundlage für unsere Schnittentwicklung und die Herstellung des Shirts verwendet. In das Shirt haben wir die nötigen Sensoren sowie Datenverarbeitungs- und Kommunikationsmodule schnitttechnisch so integriert, dass sie so wenig wie möglich stören und unabhängig von der Tragesituation immer an der richtigen Stelle positioniert sind. Das ist die Voraussetzung dafür, dass die relevanten physiologischen Daten zuverlässig gemessen werden können.” Das SmartTex Shirt soll ein durchgängiges Bild der Vitalfunktionen von Astronautinnen und Astronauten liefern. Besonders relevant wird das für zukünftige langfristige bemannte Weltraum-Missionen zu Mond und Mars.

So wird Matthias Maurer beim Experiment BEAT (Ballistocardiography for Extraterrestrial Applications and long-Term missions) als erster Astronaut ein mit Sensoren ausgestattetes T-Shirt tragen, das seine Ballistokardiografie-Daten wie Puls und relativen Blutdruck misst. Dafür wurden die Sensoren im DLR-Institut für Luft- und Raumfahrtmedizin in Köln in der Forschungsanlage :envihab kalibriert. Aus dem Datenmaterial ebenfalls ausgelesen werden können Details zur Kontraktionsrate und zu Öffnungs- und Schließzeiten der Herzklappen, die normalerweise nur über Sonographie oder Computertomographie zugänglich sind. Ziel ist es, die Auswirkungen der Weltraumumgebung auf das menschliche Herz-Kreislauf-System zu untersuchen. Um diese Auswirkungen realistisch analysieren zu können, werden die ballistokardiografischen Daten von Matthias Maurer vor, während und nach seinem Aufenthalt auf der ISS erfasst. Für die Zukunft ist ein Technologietransfer des SmartTex Shirts zur Anwendung im Bereich Fitness oder auch in der Telemedizin denkbar.

Wireless Compose-2 (WICO2)
Das Projekt wurde geplant und vorbereitet vom Deutschen Zentrum für Luft- und Raumfahrt (DLR) sowie seinen Kooperationspartnern DSI Aerospace Technology, Hohenstein und der Universität Bielefeld. Das Drahtlos-Kommunikationsnetzwerk liest Sensordaten aus und kann die Position von Menschen und Objekten im Raum durch Laufzeiten von Funkimpulsen bestimmen. Es steht zudem als Plattform für mehrere Versuche auf der ISS zur Verfügung. Dabei werden die ermittelten Daten innerhalb des Netzwerkes zwischengespeichert und in regelmäßigen Abständen von den Astronauten ausgelesen. Diese Datenpakete werden dann über die ISS-Verbindung zur Erde transferiert und von den Forschungsteams auswertet. Seine Energie kann das Kommunikationsnetzwerk durch Solarzellen aus künstlichen Lichtquellen selbst erzeugen.

19.10.2021

Teijin steigert Produktion von Carbonfaser-Prepregs für Luft- und Raumfahrtanwendungen

Teijin Limited gab heute bekannt, dass seine Carbonfaser-Tochter Renegade Materials Corporation – ein führender US-amerikanischer Anbieter von hochhitzebeständigen duroplastischen Prepregs, Harzen und Klebstoffen für die Luft- und Raumfahrtindustrie – seine Produktionskapazitäten für Prepreg um das etwa 2,5-fache erweitern wird. Die erhöhte Kapazität entspricht der Erweiterungsstrategie von Renegade am Standort Miamisburg, Ohio und ist das Ergebnis einer im Dezember 2019 getätigten Investition von 4 Millionen USD. Die Installationsarbeiten begannen im März 2020 und der Betrieb der neuen Produktionslinien wird im Januar 2022 aufgenommen.

Die hitzebeständigen duroplastischen Prepregs, Harze und Klebstoffe von Renegade Materials genießen bei US-amerikanischen und europäischen Flugzeugherstellern und Zulieferern von Flugzeugtriebwerken großes Vertrauen.

Teijin Limited gab heute bekannt, dass seine Carbonfaser-Tochter Renegade Materials Corporation – ein führender US-amerikanischer Anbieter von hochhitzebeständigen duroplastischen Prepregs, Harzen und Klebstoffen für die Luft- und Raumfahrtindustrie – seine Produktionskapazitäten für Prepreg um das etwa 2,5-fache erweitern wird. Die erhöhte Kapazität entspricht der Erweiterungsstrategie von Renegade am Standort Miamisburg, Ohio und ist das Ergebnis einer im Dezember 2019 getätigten Investition von 4 Millionen USD. Die Installationsarbeiten begannen im März 2020 und der Betrieb der neuen Produktionslinien wird im Januar 2022 aufgenommen.

Die hitzebeständigen duroplastischen Prepregs, Harze und Klebstoffe von Renegade Materials genießen bei US-amerikanischen und europäischen Flugzeugherstellern und Zulieferern von Flugzeugtriebwerken großes Vertrauen.

Renegade Materials wird sein hochhitzebeständiges duroplastisches Prepreg auf der Composites and Advanced Materials Expo (CAMX) präsentieren. Die CAMX ist einer der größten und umfassendsten Veranstaltungen für Verbundwerkstoffe und Hochleistungsmaterialien in Nordamerika und findet vom 19. bis 21. Oktober im Dallas Convention Center in Dallas, Texas statt.

Quelle:

Teijin Carbon Europe GmbH

14.10.2021

Monforts: Automated finishing at Knopf’s Sohn

Knopf’s Sohn, a contract finisher of technical textiles, has installed a fully automated Montex stenter at its plant in Helmbrechts, Germany.
Knopf’s Sohn is processing technical textiles for the automotive, aerospace, home furnishings and workwear markets, based on wool, cellulose, polyamide and polyester fabrics, along with elastane blends, in weights of 80-800gsm.

The Montex machinery range is constantly being upgraded to meet evolving customer needs for greater automation, ease of operation and energy optimisation. The latest ten chamber line at Knopf’s Sohn, with a working width of up to 2.0 metres, was engineered to specific requirements in order to accelerate the company’s move to fully automatic control of its production, and high scaffolding was required for its installation.

The line benefits from two integrated ECO Booster modules to provide high energy savings. These compact, air-to-air heat exchangers, installed within the roof structure of the line, exploit energy from the exhaust gas to preheat up to 60% of the incoming fresh air entering the stenter.

Knopf’s Sohn, a contract finisher of technical textiles, has installed a fully automated Montex stenter at its plant in Helmbrechts, Germany.
Knopf’s Sohn is processing technical textiles for the automotive, aerospace, home furnishings and workwear markets, based on wool, cellulose, polyamide and polyester fabrics, along with elastane blends, in weights of 80-800gsm.

The Montex machinery range is constantly being upgraded to meet evolving customer needs for greater automation, ease of operation and energy optimisation. The latest ten chamber line at Knopf’s Sohn, with a working width of up to 2.0 metres, was engineered to specific requirements in order to accelerate the company’s move to fully automatic control of its production, and high scaffolding was required for its installation.

The line benefits from two integrated ECO Booster modules to provide high energy savings. These compact, air-to-air heat exchangers, installed within the roof structure of the line, exploit energy from the exhaust gas to preheat up to 60% of the incoming fresh air entering the stenter.

The use of a single ECO Booster unit has been calculated to save up to 35% in energy costs, based on fixation processes. Fully automatic operation, set at the Monforts Qualitex control unit, ensures there is no additional burden on the machine operator.

The line is powered by Exxotherm indirect heating, which practically eliminates the yellowing which can be experienced during the treatment of certain polyamide and elastane-based fabrics, and is also equipped with a Conticlean circulating air filter system for constant high drying capacity.

Software
The latest Qualitex visualisation software offers operators reliability and easy control with its full HD multi-touch monitor and slider function, dashboard function with individual adaptation to operating states and faster access to comprehensive recipe data management.

With the Monformatic control system, the exact maintenance of the dwell time in combined treatment processes (drying and heat-setting) can be monitored. When the heat-setting point is reached, the fan speed is automatically adjusted, keeping energy consumption fully under control.

Quelle:

A. Monforts Textilmaschinen GmbH & Co. KG / AWOL Media

19.07.2021

ISKO to work with the MIT Computer Science & Artificial Intelligence Lab

ISKO announces its participation in CSAIL’s Alliances programme, a collaboration with CSAIL researchers, students and industry partners. Through participation in the programme, ISKO will contribute its expertise in textile innovation and collaborate on the research and development of smart textiles and wearable technologies.

The company joins a network of 26 industries – from startups to big organizations – including AI and machine learning, aerospace, healthcare, life sciences and telecommunications, as well as retail, media and entertainment.

With the goal of overall advancement of the textile and denim industry through the development of smart and wearable solutions, ISKO is stepping up to lead the change through these technologies and their many possible end-uses. The work is done in compliance with ISKO’s Responsible Innovation™ approach.

ISKO brings its innovative and agile structure, impressive production capacity and textile knowledge to the CSAIL programme which has over 1200 people, 60 research groups, 120+ researchers, 600+ students and over 900+ active projects.

ISKO announces its participation in CSAIL’s Alliances programme, a collaboration with CSAIL researchers, students and industry partners. Through participation in the programme, ISKO will contribute its expertise in textile innovation and collaborate on the research and development of smart textiles and wearable technologies.

The company joins a network of 26 industries – from startups to big organizations – including AI and machine learning, aerospace, healthcare, life sciences and telecommunications, as well as retail, media and entertainment.

With the goal of overall advancement of the textile and denim industry through the development of smart and wearable solutions, ISKO is stepping up to lead the change through these technologies and their many possible end-uses. The work is done in compliance with ISKO’s Responsible Innovation™ approach.

ISKO brings its innovative and agile structure, impressive production capacity and textile knowledge to the CSAIL programme which has over 1200 people, 60 research groups, 120+ researchers, 600+ students and over 900+ active projects.

Quelle:

ISKO / Menabò Group srl

Hexcel showcases Carbon Fiber Prepreg Capability for UAV Applications (c) Hexcel Corporation
07.07.2021

Hexcel showcases Carbon Fiber Prepreg Capability for UAV Applications

Hexcel, a global leader in advanced composites technologies, announces the successful maiden flight of a lightweight camera drone, developed using Hexcel HexPly® carbon fiber prepregs. The composite drone was developed by a team of students from the University of Applied Sciences Upper Austria in Wels with composite materials supplied by Hexcel Neumarkt in Austria.

A team of six students in the university’s lightweight construction and composite materials course was responsible for the complete design, engineering, and manufacture of the camera drone over a period of 18 months. Hexcel materials and optimization of the composite engineering enabled the team to reduce the composite structural mass by an impressive 42% compared to similar drones.

Hexcel, a global leader in advanced composites technologies, announces the successful maiden flight of a lightweight camera drone, developed using Hexcel HexPly® carbon fiber prepregs. The composite drone was developed by a team of students from the University of Applied Sciences Upper Austria in Wels with composite materials supplied by Hexcel Neumarkt in Austria.

A team of six students in the university’s lightweight construction and composite materials course was responsible for the complete design, engineering, and manufacture of the camera drone over a period of 18 months. Hexcel materials and optimization of the composite engineering enabled the team to reduce the composite structural mass by an impressive 42% compared to similar drones.

Hexcel Neumarkt was one of eight industrial partners supporting the university team throughout the project, providing all carbon fiber prepreg materials used for the drone’s landing gear as well as the fuselage. The ultra-lightweight 32g landing gear was laid up and cured in the press, whereas the fuselage was autoclave cured by the student team using Hexcel HexPly M901 and HexPly M78.1 prepreg resin systems with a combination of woven and unidirectional carbon fiber reinforcements.

With the development of Unmanned Aerial Vehicles (UAV) as a key emerging market and innovation space in the transportation sector, Hexcel’s collaboration with the University of Applied Sciences Upper Austria team not only creates an important link with the next generation of lightweight composite engineers but also highlights the weight saving and structural benefits of Hexcel composite material solutions.

"The massive weight saving achieved with their updated version of the camera drone is a fantastic achievement by the student team," said Michael Rabl, Dean of FH Wels of the Upper Austria University of Applied Sciences. "The joint study not only illustrates the wide range of complex and innovative composite techniques present in the drone sector but also presents the opportunities that exist for further development in the wider Urban Air Mobility (UAM) and aerospace composites markets.”

Hexcel congratulates the project team which includes Lukas Weninger, Karl-Heinz Schneider, Jakob Schlosser, Matthias Thon, Marla Unter, and Simone Hartl on an exceptional piece of lightweight composite design and thanks them for showcasing the contribution of Hexcel materials with a presentation and drone flight. Johanna Arndt, research and technology group leader at Hexcel Neumarkt, said, “It was a great pleasure to work with the team who were very cooperative and self-motivated to succeed. Watching the drone just fly around the Neumarkt plant was just great.”

Hexcel manufactures a complete range of carbon fibers, dry carbon UD tapes, specialty reinforcements, prepregs, and honeycomb core materials, providing customized manufacturing options for new UAM applications that combine aerospace reliability with the high-rate production required. Hexcel composite materials are the ideal solution for the lightest and most efficient cost-competitive transportation vehicles of the future.

Quelle:

Hexcel Corporation / 100% Marketing

Decision SA and Carboman Group Announce New Direct Mould Tooling Technology for Aerospace (c) Decision SA.
new direct mould tooling technology
08.03.2021

Decision SA and Carboman Group Announce New Direct Mould Tooling Technology for Aerospace

Decision SA, part of the leading European composites consortium, Carboman Group, and a specialist in the development, prototyping and production of large composite structures, is proud to announce a new direct mould tooling technology for aerospace.  Decision’s latest tooling solution provides OEMs and manufacturers with short lead times for highly stable direct moulds for series production both in and outside of the autoclave at temperatures of up to 180˚C.

Decision and Carboman recently delivered the first customer moulds using the new technology, providing a tooling glass prepreg, stainless-steel backed direct female mould tool created for the series production of a Class 3 fairing to a leading European aerospace OEM. Decision has immediate availability and capacity for similar tooling projects with lead times currently as short as six to eight weeks.

Decision SA, part of the leading European composites consortium, Carboman Group, and a specialist in the development, prototyping and production of large composite structures, is proud to announce a new direct mould tooling technology for aerospace.  Decision’s latest tooling solution provides OEMs and manufacturers with short lead times for highly stable direct moulds for series production both in and outside of the autoclave at temperatures of up to 180˚C.

Decision and Carboman recently delivered the first customer moulds using the new technology, providing a tooling glass prepreg, stainless-steel backed direct female mould tool created for the series production of a Class 3 fairing to a leading European aerospace OEM. Decision has immediate availability and capacity for similar tooling projects with lead times currently as short as six to eight weeks.

With no traditional plug or mould pattern required, Decision’s direct mould process starts with the group’s engineers selecting a material combination for the tool surface and support structure that will provide the optimum match between the coefficient of thermal expansion (CTE) of the mould and the composite part to be processed.  The CNC machined composite face sheet is supported by a stress-relieved metallic or composite backing structure before final post curing and machining is completed. The principal benefit of this novel approach, aside from removing the need for costly and time-consuming plug production, is the production accuracy delivered by the closely matched CTE of the mould tool and the finished composite part.

The autoclaved composite tool surface is not only extremely dimensionally stable up to processing temperatures of 180˚C, but it can also be configured with additional metallic inserts or fixtures if required.  

Produced in an EN 9100:2018 controlled production environment, and with CMM checks before and after machining, the new direct composite tools have dimensional tolerances of +/-0.2mm.  The available tooling dimensional envelope is currently defined by Decision’s 2200mm x 6000mm autoclave.

“With our new direct tooling technology, we are able to combine the highest technical standards in dimensional accuracy and thermal stability with extremely short lead times.  Decision and Carboman Groups’ combined mission has always been to develop the construction methods for tomorrow’s composite structures, and we believe that this tooling solution will allow our customers to accelerate the implementation of the next generation of high-performance carbon fibre aerostructures and components” Grégoire Metz, Managing Director, Decision SA.

Quelle:

Decision SA.

08.03.2021

SGL Carbon SE steigt doch noch in den SDAX auf

Die Deutsche Börse AG hat mitgeteilt, dass eine fehlerhafte Datengrundlage bezüglich der am 3. März 2021 veröffentlichten Indexveränderungen korrigiert wurde. Dies führt dazu, dass die Aktie der SGL Carbon SE zum Verkettungstermin am Montag, 22. März 2021 in den Kleinwerteindex SDAX aufgenommen wird. Der Aufstieg in den SDAX wird im Rahmen der sogenannten Regular Entry Regel vollzogen.

Der SDAX umfasst 70 Werte, die in der Rangliste nach der Marktkapitalisierung des Streubesitzes und des Börsenumsatzes auf die Werte des MDAX folgen.

„Wir freuen uns sehr, dass die Deutsche Börse ihre bisherige Entscheidung korrigiert hat und wir in den SDAX aufgenommen werden.“ sagt Dr. Torsten Derr, Vorsitzender des Vorstands der SGL Carbon SE. „Der Aufstieg ist für uns eine Bestätigung unserer bisherigen Restrukturierungsbestrebungen und zugleich Anspruch und Verpflichtung den bisherigen Weg in der Zukunft konsequent fortzusetzen.“

Die Deutsche Börse AG hat mitgeteilt, dass eine fehlerhafte Datengrundlage bezüglich der am 3. März 2021 veröffentlichten Indexveränderungen korrigiert wurde. Dies führt dazu, dass die Aktie der SGL Carbon SE zum Verkettungstermin am Montag, 22. März 2021 in den Kleinwerteindex SDAX aufgenommen wird. Der Aufstieg in den SDAX wird im Rahmen der sogenannten Regular Entry Regel vollzogen.

Der SDAX umfasst 70 Werte, die in der Rangliste nach der Marktkapitalisierung des Streubesitzes und des Börsenumsatzes auf die Werte des MDAX folgen.

„Wir freuen uns sehr, dass die Deutsche Börse ihre bisherige Entscheidung korrigiert hat und wir in den SDAX aufgenommen werden.“ sagt Dr. Torsten Derr, Vorsitzender des Vorstands der SGL Carbon SE. „Der Aufstieg ist für uns eine Bestätigung unserer bisherigen Restrukturierungsbestrebungen und zugleich Anspruch und Verpflichtung den bisherigen Weg in der Zukunft konsequent fortzusetzen.“

Quelle:

SGL Carbon SE

MaruHachi/AMAC: Thermoplastische Hochtemperatur-Tapes und Laminate (c) MaruHachi
16.02.2021

MaruHachi/AMAC: Thermoplastische Hochtemperatur-Tapes und Laminate

Mit seiner kürzlich in Betrieb genommenen Hochtemperatur-Unidirektional-Tape-Linie eröffnet der japanische Composites-Hersteller MaruHachi neue Möglichkeiten für High-End-Anwendungen in anspruchsvollen Marktsegmenten wie Luft- und Raumfahrt oder im Automobilbau und erweitert damit das Spektrum herkömmlicher, auf PP- und PA- basierender Materialien.

Mit seiner kürzlich in Betrieb genommenen Hochtemperatur-Unidirektional-Tape-Linie eröffnet der japanische Composites-Hersteller MaruHachi neue Möglichkeiten für High-End-Anwendungen in anspruchsvollen Marktsegmenten wie Luft- und Raumfahrt oder im Automobilbau und erweitert damit das Spektrum herkömmlicher, auf PP- und PA- basierender Materialien.

In einer ersten Phase wird MaruHachi bis zu 40 Tonnen/Jahr produzieren und konzentriert sich speziell auf hochtemperaturbeständige thermoplastische unidirektionale (UD) Tapes sowie mehrschichtige Plattenlaminate. Das Material basiert auf Hochleistungsfasern wie Kohlenstoff, Aramid, Glas oder Naturfasern und einer Matrix, die aus Hochleistungspolymeren wie PPS, PEEK oder anderen Hochtemperaturpolymeren bestehen kann.  Diese sind wesentlich schlagzäher als Epoxidharze und einfach zu recyceln. Mit einer Breite von 500 mm, einem spezifischen Gewicht von 60 bis 350 g/m2, je nach gewähltem Material, kann die Anlage bis zu Temperaturen von 420 Grad Celsius arbeiten. Das Herstellen unter diesen extrem hohen Temperaturen führt zu besseren Materialeigenschaften in der Endanwendung wie gesteigerte Leistungsfähigkeit, erhöhte Widerstandsfähigkeit und integrierte Hochleistungsfunktionalitäten wie sie z.B. durch das sogenannte Umspritzen erreicht werden.

Seit 2017 ist die MaruHachi Group auf dem europäischen Markt in Kooperation mit Dr. Michael Effing, Geschäftsführer der AMAC GmbH in Aachen, aktiv, der das Unternehmen strategisch berät und unterstützt. Die etablierte, familiengeführte MaruHachi Group hat eine starke Historie in den Bereichen Automobil- und Medizintextilien und ist seit mehr als 15 Jahren im Bereich innovative Verbundwerkstoffe aktiv.

Toshi Sugahara, Geschäftsführer von MaruHachi: "Wir arbeiten bereits seit vielen Jahren mit in- und ausländischen Partnern an nachfragestarken Anwendungen zusammen. Daher hat sich MaruHachi nun dazu entschlossen, in Phase 1 über 1 Mio. EUR in diese neue Anlage zu investieren, wobei ein Teil der Finanzierung von der japanischen Regierung NEDO stammt. Neue Entwicklungen in Phase 2 werden bis Ende 2021 an den nachgelagerten Technologien wie dem automatisierten Preforming und der Konsolidierung vorgenommen. Mit unseren neuen Produkten wollen wir zu einer deutlichen Gewichtsreduzierung der Endprodukte beitragen, die Energieeffizienz verbessern und gleichzeitig eine kosteneffiziente und hochwertige Lösung anbieten."

Dr. Effing, Geschäftsführer der AMAC GmbH bestätigt: "Die Fokussierung auf die Nische der Hochtemperaturprodukte auf Basis von PPS und PEEK ermöglicht es MaruHachi, sehr anspruchsvolle High-End-Anwendungen wie Strukturelemente in Raum- und Flugzeugen, Flugzeugsitze oder Triebwerkskomponenten etc. anbieten zu können. Die Tapes sind vollständig recycelbar und können beispielsweise in hoher Geschwindigkeit bis zu 0.5 Metern pro Sekunde mit laserbasierten Tape-Placement-Maschinen und Robotern verarbeitet werden."

 

Quelle:

AMAC GmbH

13.11.2020

AVK verleiht ihre Preise erstmals virtuell

Die AVK - Industrievereinigung Verstärkte Kunststoffe e.V. hat wieder die renommierten Innovationspreise vergeben. Innovative und vor allem auch nachhaltige Innovationen aus den drei Kategorien „Produkte und Anwendungen“, „Prozesse und Verfahren“ sowie „Forschung und Wissenschaft“ wurden dabei von der Experten-Jury ausgezeichnet.

Übersicht aller Preisträger in den drei Kategorien:

Kategorie „Innovative Produkte und Anwendungen“
1. Platz: „Direktgekühlter Elektromotor mit integralem Leichtbaugehäuse aus faserverstärktem Kunststoff - DEmiL“ – Fraunhofer-Institut für Chemische Technologie ICT, Pfinztal mit Karlsruher Institut für Technologie, Sumitomo Bakelite Co., Ltd.*

2. Platz: „Wiederaufbereitbare, reparierbare und recyclingfähige (3R) duroplastische Verbundwerkstoffe für wettbewerbsfähigere und nachhaltigere Industrien“ – cidetec, Donostia-San Sebastian, Spanien*

3. Platz: „Brandsichere Composite Metall Hybridstruktur LEO® Brandschutzsandwich mit integriertem Hyconnect Stahl-Glasshybridverbinder“ – SAERTEX GmbH & Co. KG mit Hyconnect GmbH*

Die AVK - Industrievereinigung Verstärkte Kunststoffe e.V. hat wieder die renommierten Innovationspreise vergeben. Innovative und vor allem auch nachhaltige Innovationen aus den drei Kategorien „Produkte und Anwendungen“, „Prozesse und Verfahren“ sowie „Forschung und Wissenschaft“ wurden dabei von der Experten-Jury ausgezeichnet.

Übersicht aller Preisträger in den drei Kategorien:

Kategorie „Innovative Produkte und Anwendungen“
1. Platz: „Direktgekühlter Elektromotor mit integralem Leichtbaugehäuse aus faserverstärktem Kunststoff - DEmiL“ – Fraunhofer-Institut für Chemische Technologie ICT, Pfinztal mit Karlsruher Institut für Technologie, Sumitomo Bakelite Co., Ltd.*

2. Platz: „Wiederaufbereitbare, reparierbare und recyclingfähige (3R) duroplastische Verbundwerkstoffe für wettbewerbsfähigere und nachhaltigere Industrien“ – cidetec, Donostia-San Sebastian, Spanien*

3. Platz: „Brandsichere Composite Metall Hybridstruktur LEO® Brandschutzsandwich mit integriertem Hyconnect Stahl-Glasshybridverbinder“ – SAERTEX GmbH & Co. KG mit Hyconnect GmbH*

Kategorie „Innovative Prozesse und Verfahren“
1. Platz: “ Robotised Injection Moulding (ROBIN)” – Robin, Dresden mit Institut für Leichtbau und Kunststofftechnik der TU Dresden*

2. Platz: „Omega Stringer völlig von der Rolle“ – Deutsches Zentrum für Luft- und Raumfahrt, Braunschweig*

3. Platz: „Hybridguss – Herstellung intrinsischer CFK-Aluminium Verbundstrukturen im Aluminiumdruckgießverfahren“ – Faserinstitut Bremen e. V. mit Fraunhofer IFAM, Bremen*

Kategorie „Forschung und Wissenschaft“
1. Platz: „Untersuchung und Zähmodifizierung neuer hochtemperaturbeständiger ungesättigter Polyesterharze und ihrer Duromere“ – FH Münster, Labor für Kunststofftechnologie und Makromolekulare Chemie, mit BASF SE Global New Business Development, Leibniz-Institut für Polymerforschung e. V., Saertex multicom GmbH*

2. Platz: „Wissenschaftliche Grundlagen zur industriellen Anwendung des thermoplastischen Resin Transfer Molding-Verfahrens (T-RTM)“ – Fraunhofer-Institut für Chemische Technologie ICT, Pfinztal*

3. Platz: „Die material- und energieeffiziente Herstellung von Turbinen Struts durch die integrative Kombination duroplastischer faserverstärkter Werkstoffe“ – Lehrstuhl für Kunststofftechnik, Uni Erlangen-Nürnberg mit Deutschem Zentrum für Luft- und Raumfahrt, Gubesch Group, Schmidt WFT, Siebenwurst, Raschig.*

Preisverleihung erstmals im Internet
Die Preisverleihung erfolgte wegen der Covid-19-Pandemie erstmals als Online-Event am 12. November 2020. Viele Innovationen der Preisträger werden dieses Jahr erneut in der AVK-Innovationspreisbroschüre präsentiert.
Diese wird online zur Verfügung gestellt: https://www.avk-tv.de/innovationaward.php

 

*Weitere Informationen finden Sie im Anhang.

 

Quelle:

AVK – Industrievereinigung Verstärkte Kunststoffe e.V

Thomas Dippold (c) Schaltbau Holding
Thomas Dippold
15.10.2020

SGL Carbon SE: Thomas Dippold becomes member of the Board of Management

As reported on August 17, 2020, the Supervisory Board of SGL Carbon SE had appointed Thomas Dippold to CFO and member of the Board of Management of SGL Carbon SE effective December 1, 2020. Fortunately, Mr. Dippold is able to assume office of his mandate as member of the Board of Management of SGL Carbon SE earlier, so that the Supervisory Board of the company has brought forward the appointment to October 15, 2020, also to prepare for the planned assumption of the CFO position.

As previously reported, and effective December 1, 2020, Mr. Dippold is succeeding the long-standing CFO Dr. Michael Majerus, who is resigning from his office effective November 30, 2020 by mutual amicable consent.

As planned, Dr. Stephan Bühler resigned from his office as member of the Board of Management effective October 15, 2020.

As reported on August 17, 2020, the Supervisory Board of SGL Carbon SE had appointed Thomas Dippold to CFO and member of the Board of Management of SGL Carbon SE effective December 1, 2020. Fortunately, Mr. Dippold is able to assume office of his mandate as member of the Board of Management of SGL Carbon SE earlier, so that the Supervisory Board of the company has brought forward the appointment to October 15, 2020, also to prepare for the planned assumption of the CFO position.

As previously reported, and effective December 1, 2020, Mr. Dippold is succeeding the long-standing CFO Dr. Michael Majerus, who is resigning from his office effective November 30, 2020 by mutual amicable consent.

As planned, Dr. Stephan Bühler resigned from his office as member of the Board of Management effective October 15, 2020.

Quelle:

SGL Carbon SE