From the Sector

Reset
13 results
Composites production volume in Europe since 2011 (in kt) Graphik AVK – Industrievereinigung Verstärkte Kunststoffe e. V.
Composites production volume in Europe since 2011 (in kt)
06.03.2024

European composites market on the level of 2014

After a long phase of continuous growth, the composites market has seen strong fluctuations since 2018. In 2023, the overall market for composites in Europe fell by 8%.

The current mood on the markets in Germany and Europe is rather negative within the industry. The main drivers are the persistently high energy and raw material prices. Added to this are problems in logistics chains and a cautious consumer climate. A slowdown in global trade and uncertainties in the political arena are fueling the negative sentiment. Despite rising registration figures, the automotive industry, the most important application area for composites, has not yet returned to its pre-2020 volume. The construction industry, the second key application area, is currently in crisis. These factors have already caused the Eu-ropean composites production volume to fall significantly in recent years. There has now been another decline in Europe for 2023.

After a long phase of continuous growth, the composites market has seen strong fluctuations since 2018. In 2023, the overall market for composites in Europe fell by 8%.

The current mood on the markets in Germany and Europe is rather negative within the industry. The main drivers are the persistently high energy and raw material prices. Added to this are problems in logistics chains and a cautious consumer climate. A slowdown in global trade and uncertainties in the political arena are fueling the negative sentiment. Despite rising registration figures, the automotive industry, the most important application area for composites, has not yet returned to its pre-2020 volume. The construction industry, the second key application area, is currently in crisis. These factors have already caused the Eu-ropean composites production volume to fall significantly in recent years. There has now been another decline in Europe for 2023.

Overall development of the composites market
The volume of the global composites market totalled 13 million tons in 2023. Compared to 2022, with a volume of 12.3 million tons, growth was around 5%. In comparison, the European composites production volume fell by 8% in 2023. The total European composites market thus comprises a volume of 2,559 kilotons (kt) after 2,781 kt in 2022.

The market is therefore declining and falling back to the level of 2014. Overall, market momentum in Europe was lower than in the global market. Europe's share of the global market is now around 20%.

As in previous years, development within Europe is not uniform. The differences are due to very different regional core markets, the high variability of the materi-als used, a wide range of different manufacturing processes and widely differing areas of application. Accordingly, there are different regional trends, especially with regard to the individual processes, although there were declines in all re-gions and for almost all processes in 2023. At almost 50% of the market volume, the transportation sector accounts for the largest share of total composites pro-duction in terms of volume. The next two largest areas are the electri-cal/electronics sector and applications in construction and infrastructure.

The entire market report 2023 is available for download: https://www.avk-tv.de/publications.php.

05.10.2023

EURATEX and CIE warn EU Presidency about de-industrialised Europe

Ahead of the extra-ordinary Council on 6 October in Granada, EURATEX President, Alberto Paccanelli, and CIE President, Jose Vte Serna, call on the EU Presidency to develop a new competitiveness strategy, which can relaunch the European industry and ensure it will remain competitive in the decades to come. This means bringing together trade, energy, state aid and sustainability policies into a single, integrated, comprehensive approach, which can support a robust and modern European manufacturing industry.  
 
To consolidate a strong industrial structure in Europe, the Union should

Ahead of the extra-ordinary Council on 6 October in Granada, EURATEX President, Alberto Paccanelli, and CIE President, Jose Vte Serna, call on the EU Presidency to develop a new competitiveness strategy, which can relaunch the European industry and ensure it will remain competitive in the decades to come. This means bringing together trade, energy, state aid and sustainability policies into a single, integrated, comprehensive approach, which can support a robust and modern European manufacturing industry.  
 
To consolidate a strong industrial structure in Europe, the Union should

  1. secure the supply of clean energy at a competitive cost;
  2. support innovation and foster the necessary talent pool and
  3. be more assertive in achieving an international level-playing field on sustainability, based on the European model.  

During the past few years the implementation of incoherent and conflicting objectives under the trade, energy, industrial and sustainability policy has been observed. As a matter of fact, while the circular economy promised to be a recipe for a competitive industry of the future, the likelihood of pushing the EU industry out of the market and driving investment elsewhere than in Europe is very high. If this approach were to continue in the next years, it will result in a de-industrialised Europe, depending on imports from abroad. Such a Europe would be more exposed to geopolitical turmoil, with no agency to deliver its vision of peace, well-being and a healthy environment to its citizens.

It is fundamental for Europe to pursue a more coherent set of policies that put the competitiveness of its domestic industry at the core. In this context, all the industrial manufacturing sectors should be in the scope, including the textile industry, given its importance in providing essential products and applications to our society. A first impactful action that can be taken in this direction, would be to expand the scope of the Net-Zero Industry Act (NZIA) to include the textiles and clothing industry.
 
The history of European industry is fully woven in the birth and expansion of the European textiles industry since the XVIII century. Still today, the European textiles and clothing industry holds a pivotal position in the market, encompassing a diverse range of sectors and applications. In terms of employment, our industry creates 1,3 million direct jobs in Europe, encompassing a wide range of roles, from design and production to distribution and retail. European textiles have a wide range of applications, the most common one is of course clothing and fashion. The industry has a long history of producing high-quality apparel, with various regions specializing in specific niches.
 
Beyond clothing, there is a wide range of industrial sectors were textiles play an essential role, including  Automotive (used for upholstery, interior components, and even lightweight composite materials), Aircraft and Shipbuilding (where textiles are employed for their lightweight and high-strength properties, to enhance fuel efficiency, reduce emissions, and improve overall performance), Building and Construction (insulation, roofing, geotextiles, and architectural textiles), or Personal Protective Equipment, for medical personnel, firefighters, police and army officers. This includes masks, gowns, uniforms, helmets, and fire-resistant clothing, ensuring safety in hazardous environments.
 
Textiles are essential components of our society and our well-being. It is key for Europe to maintain its capacity to manufacture high-quality, sustainable and high-technology textiles.  With this in mind, the competitiveness policy of the future and the related funds to support it, should include the textile ecosystem in its scope.  

 

More information:
Euratex EU council Policy Hub
Source:

Euratex

20.09.2023

TMAS Members at ITMA Asia + CITME 2023

Members of TMAS – the Swedish Textile Machinery Association – will be taking part in the forthcoming ITMA Asia + CITME exhibition, taking place from November 19-23 2023 at the National Exhibition and Convention Centre in Shanghai, China.

Weaving
In the area of weaving, 93% of the 114,000 new looms delivered in 2022 went to Asia, according to the latest figures from the International Textile Manufacturers Federation (ITMF), with China the top destination, followed by India.
As a result, TMAS members like Vandewiele Sweden AB and Eltex have a huge market to address that has been established over many decades.

Vandewiele Sweden AB benefits from all of the synergies and accumulated know-how of the market-leading Vandewiele Group, supplying weft yarn feeding and tension control units for weaving looms to the majority of weaving machine manufacturers. It also retrofits its latest technologies to working mills to enable instant benefits in terms of productivity and control.

Members of TMAS – the Swedish Textile Machinery Association – will be taking part in the forthcoming ITMA Asia + CITME exhibition, taking place from November 19-23 2023 at the National Exhibition and Convention Centre in Shanghai, China.

Weaving
In the area of weaving, 93% of the 114,000 new looms delivered in 2022 went to Asia, according to the latest figures from the International Textile Manufacturers Federation (ITMF), with China the top destination, followed by India.
As a result, TMAS members like Vandewiele Sweden AB and Eltex have a huge market to address that has been established over many decades.

Vandewiele Sweden AB benefits from all of the synergies and accumulated know-how of the market-leading Vandewiele Group, supplying weft yarn feeding and tension control units for weaving looms to the majority of weaving machine manufacturers. It also retrofits its latest technologies to working mills to enable instant benefits in terms of productivity and control.

Yarn and sewing thread monitoring
With nearly 70 years of expertise in yarn sensor technology, Eltex of Sweden AB has been at the forefront of new product development. Its EYE and EyETM systems are capable of accurately and efficiently monitoring the movement and tension of more than 1,000 yarns simultaneously. These systems are suitable for various applications and fibre types, including warping, winding, multiaxial weaving and new material applications.

Eltex sewing tension monitors, such as the ETM422, have been well-received by customers. This device can monitor the tension of sewing threads in real time, effectively improving the quality and safety of sewn products. Particularly in China's rapidly growing automotive manufacturing sector, the ETM422 has seen widespread use to meet the industry’s escalating demands for product safety and quality.

Dyeing and finishing
“Digitalisation, automation and AI have become the key enablers for sustainable gains across the entire textile industry and so much has been achieved in the past few years, especially in terms of automation,” says TMAS secretary general Therese Premler-Andersson. “One area in which TMAS members are really making a difference right now, is in replacing water and energy-intensive technologies for the dyeing and finishing processes with new digital technologies.”

The TexCoat G4 non-contact spray technology for textile finishing and remoistening, for example, will be showcased in Shanghai by Baldwin. It not only reduces water, chemicals and energy consumption, but also provides the flexibility to adapt to a customer’s requirements in terms of single and double-sided finishing applications. The TexCoat G4 can reduce water consumption by as much as 50% compared to traditional padding application processes.

Photo: AVK
26.05.2023

AVK: Successful Flame Retardancy Conference in Berlin

  • Flame Retardancy for Composites Applications in the Transport Sector

On 10-11 May 2023, the AVK - Industrievereinigung Verstärkte Kunststoffe e. V. in cooperation with the FGK - Forschungsgesellschaft Kunststoffe e.V. in Berlin organised for the first time an international, English-language conference on flame retardancy.

In 18 compact lectures, more than 20 experts informed nearly 80 participants about new developments, requirements and innovations regarding specific flame retardant properties of components made of fibre-reinforced plastics/composites for the transport sector.

Among others, there were presentations by industry representatives from Saertex, BÜFA, Clariant, Diehl Aviation and Airbus, but also from institutes such as the Fraunhofer Institutes or the Federal Institute for Materials Research and Testing. Presentations on the topics of standardisation, raw materials, automotive or recycling were on the agenda, but also flame retardants for connectors and battery housings for electric vehicles or fire-retardant systems for rail vehicles or fire-retardant CFRP made from recycled CF nonwoven were presented.

  • Flame Retardancy for Composites Applications in the Transport Sector

On 10-11 May 2023, the AVK - Industrievereinigung Verstärkte Kunststoffe e. V. in cooperation with the FGK - Forschungsgesellschaft Kunststoffe e.V. in Berlin organised for the first time an international, English-language conference on flame retardancy.

In 18 compact lectures, more than 20 experts informed nearly 80 participants about new developments, requirements and innovations regarding specific flame retardant properties of components made of fibre-reinforced plastics/composites for the transport sector.

Among others, there were presentations by industry representatives from Saertex, BÜFA, Clariant, Diehl Aviation and Airbus, but also from institutes such as the Fraunhofer Institutes or the Federal Institute for Materials Research and Testing. Presentations on the topics of standardisation, raw materials, automotive or recycling were on the agenda, but also flame retardants for connectors and battery housings for electric vehicles or fire-retardant systems for rail vehicles or fire-retardant CFRP made from recycled CF nonwoven were presented.

More information:
AVK Composites flame retardant
Source:

AVK

Photo: Euratex
26.10.2022

EURATEX & ATP Convention successfully concluded in Porto

  • European textile industry needs to prepare for a paradigm shift, and become global leader in sustainable textiles

Organised by EURATEX in partnership with the Portuguese Textile Association (ATP), the Porto Convention – Sustainability meets Competitiveness: How to Square the Circle? – took place on 13-14 October in Porto, Portugal, with nearly 250 entrepreneurs attending from all over Europe. They discussed the current challenges of the European textile industry and set the grounds for a bright future, based on some strong foundations: innovation, creativity, quality and sustainability.

In his keynote speech, Mr. Pedro Siza Vieira, Former Minister for the Economy and Digital Transition of Portugal, assessed the geopolitical and macroeconomics changes, and how this will impact on the future of the textile industry: nearshoring and friend-shoring, independence from foreign gas through the use of European sustainable energy, as well as circular and automated production lines. While the current turbulence causes uncertainty, he sees a better future for our industry.

  • European textile industry needs to prepare for a paradigm shift, and become global leader in sustainable textiles

Organised by EURATEX in partnership with the Portuguese Textile Association (ATP), the Porto Convention – Sustainability meets Competitiveness: How to Square the Circle? – took place on 13-14 October in Porto, Portugal, with nearly 250 entrepreneurs attending from all over Europe. They discussed the current challenges of the European textile industry and set the grounds for a bright future, based on some strong foundations: innovation, creativity, quality and sustainability.

In his keynote speech, Mr. Pedro Siza Vieira, Former Minister for the Economy and Digital Transition of Portugal, assessed the geopolitical and macroeconomics changes, and how this will impact on the future of the textile industry: nearshoring and friend-shoring, independence from foreign gas through the use of European sustainable energy, as well as circular and automated production lines. While the current turbulence causes uncertainty, he sees a better future for our industry.

The first CEO Panel, addressing the theme of How to Measure and Communicate about Sustainability, focused on the challenges to translate “sustainability” towards the consumers. The panel addressed the issue of greenwashing and the role of brands in communicating about sustainability. It looked at how the new European Commission regulations on eco-label, digital product passport (DPP) and product environmental footprint (PEF) will create a new framework.

The second CEO Panel, discussing Financing Sustainability, looked at the cost of sustainable investments, and how this cost should be managed within the entire supply chain, including the brands and retailers.

Four workshops with industry experts followed in the afternoon, addressing the themes of Extended Producer Responsibility (EPR) in Textiles, Digital Product Passport (DPP), Recycling Textile Waste and Labelling Textiles (Product Environmental Footprint). As these initiatives will roll out in the coming years – as part of the EU Textile Strategy – participants got a better understanding of the future framework for our industry.

Dirk Vantyghem, Director General of EURATEX, commented on this: “to prepare for a brighter future requires a new regulatory framework, where quality and durability become the norm, where transparency and sustainability is rewarded, where free riders – who do not comply with rules and standards – are kept outside the market. The EU Textile Strategy aims at creating such a framework, which must be fair and balanced, and requires a close and constant dialogue between the regulator and the industry.”

During the 2nd day of the convention, participants had the opportunity to visit state of the art textile companies (Têxteis J.F. Almeida, RIOPELE, and TMG Automotive) and the Portuguese textile  research centre CITEVE. They showcased how the Portuguese textile industry is making this transition, while remaining globally competitive.

Alberto Paccanelli, President of EURATEX, concluded: “We need to attract creative people in our companies, we need to produce top class quality products, and we need to become more sustainable. That is the recipe for our success in a globalised and highly competitive industry.” Paccanelli is positive about the future: “While we face very tough times, I am optimistic about the future of our European textile industry. The rest of the world is watching us, as we move forward with our strategy. We should become their benchmark and Europe should become a global leader in sustainable textiles.”

 

Source:

Euratex

Photo Pixabay
16.09.2022

Euratex, EuroCoton, Edana, CIRFS and ETSA join forces for the European Textile Industry

The associations published a joint European textiles industry statement on the energy package claiming incisive actions with no further delay.
Here is the statement in full:

Last month, when gas wholesale prices reached the record level of 340€/MWh – triggering also sky-high electricity prices – the European textiles industry called on the European Union to adopt a wholesale price cap for gas, the revision of the merit-order principle in the electricity market, support for SMEs and a single European strategy. On 14 September 2022, on the occasion of the State of the Union address by President Von der Leyen, the Commission announced initiatives aimed at tackling the dramatic energy crisis that the Europe is facing.

We, the European associations representing the whole textiles’ ecosystem,  welcome these proposals by the Commission to change the TTF benchmark parameters and decouple the TTF from the electricity market and the revision of the merit-order principle for the electricity market, which is no longer serving the purpose it was designed for.

The associations published a joint European textiles industry statement on the energy package claiming incisive actions with no further delay.
Here is the statement in full:

Last month, when gas wholesale prices reached the record level of 340€/MWh – triggering also sky-high electricity prices – the European textiles industry called on the European Union to adopt a wholesale price cap for gas, the revision of the merit-order principle in the electricity market, support for SMEs and a single European strategy. On 14 September 2022, on the occasion of the State of the Union address by President Von der Leyen, the Commission announced initiatives aimed at tackling the dramatic energy crisis that the Europe is facing.

We, the European associations representing the whole textiles’ ecosystem,  welcome these proposals by the Commission to change the TTF benchmark parameters and decouple the TTF from the electricity market and the revision of the merit-order principle for the electricity market, which is no longer serving the purpose it was designed for.

We also welcome the proposal to amend the state-aid framework that, in our view, should include the textiles finishing, the textiles services and the nonwoven sectors as well as a simplification of the application requirements. Furthermore, we call for a uniform implementation across the EU.

However, we acknowledge that the Commission proposal lacks in ambition and – if confirmed – it will come at the cost of losing European industrial capacity and European jobs. Ultimately, Europe will remain without its integrated textiles ecosystem, as we know it today, and no mean to translate into reality the EU textiles strategy, for more sustainable and circular textiles products.

An ambitious and meaningful European price cap on the wholesale price of natural gas is absolutely necessary. Europe is running out of time to save its own industry. It is now time to act swiftly, decisively in unity and solidarity at European level. We understand a very high price cap has been so far discussed among Ministries and that is not reassuring for companies across Europe: if any cap is, as expected, above 100/MWh, these businesses will collapse.

Already in March 2022, with EU gas wholesale prices at 200€/MWh, the business case for keeping textiles production was no longer there. To date, natural gas wholesale prices have reached the level of 340€/MWh, more than 15 times higher compared to 2021! Currently, many businesses have suspended their production processes to avoid the loss of tens of thousands of euros every day. We hope this will not become the new normal and – to reduce the likelihood of such a scenario – we call on the Commission, the EU Council and the Parliament to swiftly adopt decisive, impactful and concrete actions to tackle the energy crisis and ensure the survival of the European industry.

Given the dire international competition in which the EU textiles industry operates, it is not possible to just pass on the increased costs to consumers. Yet, with these sky-high prices, our companies cannot afford to absorb those costs. The EU textiles companies are mainly SMEs that do not have the financial structure to absorb such a shock.  In contrast with such reality in Europe, the wholesale price of gas in the US and China is 10€/MWh, whereas in Turkey the price is 25€/MWh. If the EU does not act, our international competitors will easily replace us in the market, resulting in the de-industrialisation of Europe and a worsened reliance on foreign imports of essential products.

Specific segments of the textile industry are particularly vulnerable:

  • The man-made fibres (MMF) industry for instance is an energy intensive sector and a major consumer of natural gas and electricity in the manufacturing of its fibres. Not only is it being affected by higher energy process, it is also experiencing shortages and sharply rising costs of its raw materials.
  • For the nonwovens segment, production processes – which use both fibres and filaments extruded in situ – are also highly dependent on gas and electricity. Polymers melting and extrusion, fibres carding, web-forming, web-bonding and drying are energy-intensive techniques. Nonwoven materials can be found in many applications crucial to citizens like in healthcare (face masks) or automotive (batteries).
  • It also is to be noted that for some segments the use of gas has no technological substitute: for example, the dyeing and finishing production units make very intense use of gas. These production units are mainly composed by boilers and driers, which only work on gas and there is no alternative technology.
  • The textile services sector is also struggling: with the critical nature of the service they provide, they require a considerable amount of energy to keep services, particularly hospitals and care homes stocked with lifesaving material as well as clothing and bed linens for the patients themselves. Losing these businesses would cause a lack of clothing for healthcare professionals, including protective sanitary gowns for surgeons, nurses and doctors, uniforms including other forms of personal protective equipment.
Source:

Euratex

07.07.2022

Successful SMCCreate design conference in Antwerp

With over 60 participants from Europe and Turkey, the first SMCCreate Design Conference took place in Antwerp from 28-29 June. The conference was jointly organised by AVK – Federation of Reinforced Plastics and the European Allicance for SMC BMC. The topics covered the wide spectrum of SMC and BMC manufacturing, from design to sustainability solutions. 16 speakers from different European countries showed what is important in component manufacturing and design, and which solutions the companies offer in regard to materials, performance and much more.

After an overview of the general market developments and how the economic requirements affect component manufacturing, the focus was on the possibilities to enable sustainable design with SMC/BMC. In the second conference section „part design“, the topics of design and modelling, design with structural analysis and flow simulation, standards, and best class solutions as well as surface modification were presented.

With over 60 participants from Europe and Turkey, the first SMCCreate Design Conference took place in Antwerp from 28-29 June. The conference was jointly organised by AVK – Federation of Reinforced Plastics and the European Allicance for SMC BMC. The topics covered the wide spectrum of SMC and BMC manufacturing, from design to sustainability solutions. 16 speakers from different European countries showed what is important in component manufacturing and design, and which solutions the companies offer in regard to materials, performance and much more.

After an overview of the general market developments and how the economic requirements affect component manufacturing, the focus was on the possibilities to enable sustainable design with SMC/BMC. In the second conference section „part design“, the topics of design and modelling, design with structural analysis and flow simulation, standards, and best class solutions as well as surface modification were presented.

A rather newer field was highlighted on Day 2 with Carbon SMC, discussing mobility and automotive applications. These included the integration of multiple material technologies, not forgetting the possibility of implementing green deal strategies here too. The advantages of SMC in automotive components for electrification were explained in more detail. The conference concluded with a sporty presentation on the development of a carbon SMC rear frame for a downhill mountain bike.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

25.05.2022

SMCCreate Conference: Programme completed

The SMCCreate Conference provides information on design with SMC and BMC composites and offers valuable insights into the entire product design process from the idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials. 15 lectures by international speakers from France, Germany, Italy, Spain, The Netherlands and the USA will present practical presentations about sustainability, part design, mobility and automotive applications. Equally current trends and developments in the European SMC/BMC market are on the agenda. The presentation language will be English.

The SMCCreate Conference provides information on design with SMC and BMC composites and offers valuable insights into the entire product design process from the idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials. 15 lectures by international speakers from France, Germany, Italy, Spain, The Netherlands and the USA will present practical presentations about sustainability, part design, mobility and automotive applications. Equally current trends and developments in the European SMC/BMC market are on the agenda. The presentation language will be English.

The winner of the SMC BMC Design Award 2022 , Isa Buitenhuis completes the programme of the SMCCreate Design Conference 2022 from 28-29 June in Antwerp. The TU Delft student will present her winning design LightTurn in a lecture. This shower panel makes showering a completely new experience, as the shower fitting can be extended to suit the age of the user. It combines a seat, water-saving elements and even lighting in a modern design. The award is offered by the European Alliance for SMC BMC and took place during the JEC World in Paris at the beginning of May.

The SMCCreate 2022 Conference will be organized on June 28-29, 2022 in the Hilton Hotel in Antwerp (Belgium).

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

29.03.2022

SMCCreate 2022 design conference – programme available

SMCCreate 2022, the design conference jointly organized by the AVK and the European Alliance for SMC BMC takes place from 28-29 June 2022 in Antwerp, Belgium. Registrations are now possible.

This unique conference about design in SMC and BMC composite materials will provide valuable insights in the entire product design process from idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials.

Within the time of only 1.5 day, the SMCCreate 2022 conference will cover a wide range of subjects, all relevant for designers in their selection of materials solutions that provide performance, cost efficiency, manufacturing ability and sustainability.

Program
15 lectures by international speakers from France, Germany, Italy, Spain, The Netherlands and the USA will present practical presentations about sustainability, part design, mobility and automotive applications. Equally current trends and developments in the European SMC/BMC market are on the agenda.

SMCCreate 2022, the design conference jointly organized by the AVK and the European Alliance for SMC BMC takes place from 28-29 June 2022 in Antwerp, Belgium. Registrations are now possible.

This unique conference about design in SMC and BMC composite materials will provide valuable insights in the entire product design process from idea to part manufacturing, targeted both at experienced designers and at designers that are new in applying these versatile materials.

Within the time of only 1.5 day, the SMCCreate 2022 conference will cover a wide range of subjects, all relevant for designers in their selection of materials solutions that provide performance, cost efficiency, manufacturing ability and sustainability.

Program
15 lectures by international speakers from France, Germany, Italy, Spain, The Netherlands and the USA will present practical presentations about sustainability, part design, mobility and automotive applications. Equally current trends and developments in the European SMC/BMC market are on the agenda.

Date and Location
The SMCCreate 2022 Conference will be organized on June 28-29, 2022 in the Hilton Hotel in Antwerp (Belgium). The presentation language will be English. The programme, further details and registration information is available at www.avk-tv.de.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

24.02.2022

NCTO: Deputy U.S. Trade Representative Sarah Bianchi visits Shawmut Corporation

Shawmut Corporation hosted Deputy United States Trade Representative Sarah Bianchi at the company’s headquarters and state-of-the-art manufacturing facility in West Bridgewater, Mass., as part of the ambassador’s inaugural visit to textile manufacturing facilities in the New England area.

Ambassador Bianchi’s visit comes at a pivotal time for the U.S. textile supply chain, which produced $64 billion in output in 2020 and employed nearly 530,000 workers. Shawmut Corporation is part of the broader U.S. textile industry that has been at the forefront of a domestic production chain that has collectively manufactured over one billion personal protective equipment (PPE) items during the COVID-19 pandemic.

Shawmut Corporation hosted Deputy United States Trade Representative Sarah Bianchi at the company’s headquarters and state-of-the-art manufacturing facility in West Bridgewater, Mass., as part of the ambassador’s inaugural visit to textile manufacturing facilities in the New England area.

Ambassador Bianchi’s visit comes at a pivotal time for the U.S. textile supply chain, which produced $64 billion in output in 2020 and employed nearly 530,000 workers. Shawmut Corporation is part of the broader U.S. textile industry that has been at the forefront of a domestic production chain that has collectively manufactured over one billion personal protective equipment (PPE) items during the COVID-19 pandemic.

The ambassador’s visit to Shawmut included a tour of the company’s manufacturing facility and a roundtable discussion highlighting the critical need for policies supporting a domestic supply chain and the innovative nature of the modern textile industry and its important contribution to the U.S. economy. Shawmut, a fourth-generation, family-run global advanced materials and textile manufacturer, is a global leader in automotive textile composites, innovative technical fabrics and custom laminating services, employing more than 700 employees worldwide with 10 global manufacturing plants and seven commercial offices. The company has also contributed greatly to U.S. PPE efforts, investing $20 million in a new state-of-the-art facility, which can produce up to 180 million NIOSH-approved N95 respirators and other PPE annually and created hundreds of new local jobs.

Ambassador Bianchi said, “Today’s tour of Shawmut’s manufacturing facilities and the roundtable discussion with textile industry executives was an invaluable opportunity for me to see innovative U.S. textile manufacturing first-hand, to learn more about the challenges that U.S. textile manufacturing faces, and to explore ways in which the Administration and industry can cooperate to support a worker-centric trade policy.”

During the visit, U.S. textile executives spanning the fiber, yarn, fabric, and finished product textile and apparel industries participated in a roundtable with the ambassador at which they discussed the innovative achievements and competitiveness of the domestic industry and outlined priority issues in Washington, such as the importance of Buy American and Berry Amendment government procurement policies, maintaining strong rules of origins in free trade agreements and the need to address larger systemic trade issues with China.

VDMA: Top young talent with cutting-edge topics  (c) VDMA
The 2021 winners (from top left to right): Dr Martin Hengstermann, Irina Kuznik, Kai-Chieh Kuo.
10.11.2021

VDMA: Top young talent with cutting-edge topics

The Chairman of the Walter Reiners-Stiftung foundation of the VDMA Textile Machinery Association, Peter D. Dornier has awarded prizes to three successful young engineers. The award-winning works provide practical solutions on the topic of circular economy. For example, the recycling of carbon fibres, which are used to produce lightweight components for the automotive industry. Or the environmentally friendly production of yarns from crab shells. Another topic was medical applications: The processing of ultra-fine yarns into stents for aortic repair. The award ceremony took place online on 9 November as part of the Aachen-Dresden-Denkendorf International Textile Conference.  

With a creativity prize, endowed with 3,000 euros, the foundation honoured the diploma thesis of Irina Kuznik, TU Dresden. She used a creative approach to realise solutions for processing chitosan into fibre yarn.

The Chairman of the Walter Reiners-Stiftung foundation of the VDMA Textile Machinery Association, Peter D. Dornier has awarded prizes to three successful young engineers. The award-winning works provide practical solutions on the topic of circular economy. For example, the recycling of carbon fibres, which are used to produce lightweight components for the automotive industry. Or the environmentally friendly production of yarns from crab shells. Another topic was medical applications: The processing of ultra-fine yarns into stents for aortic repair. The award ceremony took place online on 9 November as part of the Aachen-Dresden-Denkendorf International Textile Conference.  

With a creativity prize, endowed with 3,000 euros, the foundation honoured the diploma thesis of Irina Kuznik, TU Dresden. She used a creative approach to realise solutions for processing chitosan into fibre yarn.

Mr Kai-Chieh Kuo was awarded the diploma/master's thesis promotion prize of 3,500 euros. With his master's thesis, which was written at RWTH Aachen University, Mr Kuo contributes to the production of vital components used in medicine. The stents made of ultra-fine yarns are made possible by an innovative modification of the classic tube weaving process.

The Walter Reiners Foundation rewarded the doctoral thesis of Dr. Martin Hengstermann with the promotional prize in the dissertation category, endowed with 5,000 euros. The thesis deals with the production of recycled carbon fibres. These can be used to produce lightweight components for motor vehicle and aircraft construction or the wind energy sector.

New Prize Sustainability / Circular Economy
The environmental conditions of the textile industry and machine construction are changing. Topics such as climate protection and the circular economy are becoming central. From this perspective, the board of the Walter Reiners Foundation has decided to further develop the foundation's prize system.

In 2022, the foundation will for the first time offer a prize with a focus on design / sustainability. Peter D. Dornier, Chairman of the Foundation, explained: "Already in the design phase, one can set the parameters so that a textile product can be reintroduced after use into the economic cycle for a high-quality application. For example, through the appropriate use of materials and finishing. We are looking for solutions for resource-saving design, technology and manufacturing processes."   

Zuse-Gemeinschaft: Biogene Schäume und Fasern für den Auto-Innenraum (c) Zuse-Gemeinschaft
08.10.2021

Zuse-Gemeinschaft: Biogene Schäume und Fasern für den Auto-Innenraum

Vom Biomasseanbau und der energetischen Nutzung über das Herstellen von Zwischenprodukten bis hin zum Verwenden biogener Ressourcen in langlebigen Verbraucherprodukten: die Bioökonomie umgibt uns schon heute tagtäglich. Doch welche Innovationen zeichnen sich ab, um die Wirkung biogener Ressourcen im Sinne des Klimaschutzes zu maximieren? Das war Thema beim Online-Werkstattgespräch Bioökonomie der Zuse-Gemeinschaft am 6. Oktober.

CO2 einsparen durch biogene Schäume und Fasern für den Auto-Innenraum
Wie textile Anwendungen aus der Bioökonomie verstärkt in einem Schlüsselbereich der Energiewende - der Mobilität - zum Zuge kommen können, berichtete Dr. Frank Meister, Abteilungsleiter Chemische Forschung beim Thüringischen Institut für Textil- und Kunststoff-Forschung (TITK) anhand des von der Europäischen Union geförderten Projekts BioMotive.

Vom Biomasseanbau und der energetischen Nutzung über das Herstellen von Zwischenprodukten bis hin zum Verwenden biogener Ressourcen in langlebigen Verbraucherprodukten: die Bioökonomie umgibt uns schon heute tagtäglich. Doch welche Innovationen zeichnen sich ab, um die Wirkung biogener Ressourcen im Sinne des Klimaschutzes zu maximieren? Das war Thema beim Online-Werkstattgespräch Bioökonomie der Zuse-Gemeinschaft am 6. Oktober.

CO2 einsparen durch biogene Schäume und Fasern für den Auto-Innenraum
Wie textile Anwendungen aus der Bioökonomie verstärkt in einem Schlüsselbereich der Energiewende - der Mobilität - zum Zuge kommen können, berichtete Dr. Frank Meister, Abteilungsleiter Chemische Forschung beim Thüringischen Institut für Textil- und Kunststoff-Forschung (TITK) anhand des von der Europäischen Union geförderten Projekts BioMotive.

Das TITK ist dort eingebunden in die Entwicklung biogener Fasern und neuer Leichtbauwerkstoffe für den Auto-Innenraum, wo sie z.B. für Sitze, Armaturenbrett oder Türinnenverkleidung gebraucht werden. Unter anderem entwickelten die Forschenden neue sogenannte Lyocellfasern aus modifizierten Papierzellstoffen. Der besondere Vorzug am TITK: An dem Thüringer Institut konnten die neu entwickelten Fasern in einer kleintechnischen Versuchsanlage im Maßstab von mehreren 100 kg hergestellt werden. Das erhöht die Vergleichbarkeit mit den Realitäten der Industrie und war Design-Basis für eine unlängst errichtete Demo-Anlage der Metsä-Tochter MI Demo im finnischen Äänekoski. „Lyocellfasern als biogener Werkstoff vermeiden Umweltbelastungen wie sie bei anderen Materialien durch die Risiken von Mikroplastik entstehen. Hinzu kommt als Klima-Plus: Durch die von uns mit entwickelten und bewerteten Fasern und Verfahrensprinzipien lässt sich der CO2-Fußabdruck bei der Produktion von Fahrzeugen spürbar verringern“, erklärt Meister.

Kombination von CO2-Elektrolyse und Biotech-Wertstoffsynthese
Dass mithilfe von Bioökonomie-Lösungen CO2 nicht nur eingespart werden kann, sondern auch negative Emissionen des Klimagases erreichbar sind, deutete Dr. Markus Stöckl vom DECHEMA-Forschungsinstitut (DFI) an. In seinem Vortrag „Mit Strom und CO2 zum Biokunststoff“ zeigte er auf, wie die Elektrolyse dazu genutzt werden kann, Erneuerbare Energien „lagerbar“ zu machen. Der Ansatz: Aus Kohlendioxyd so genanntes Formiat zu produzieren, das als Feststoff lagerbare Salz der Ameisensäure, das Mikroorganismen als Energie- und Kohlenstoffquelle dienen kann, die wiederum daraus den Biokunststoff Polyhydroxybutyrat (PHB) herstellen. Durch die elektrochemische Herstellung des Zwischenprodukts Formiat können unterschiedliche Mikroorganismen eingesetzt werden.

Source:

Zuse-Gemeinschaft

(c) TMAS
26.04.2019

Innovate or die: TMAS at ITMA 2019

A focus on customer service, aligned with the drive to constantly innovate, has long ensured that the member companies of TMAS – the Swedish texile machinery manufacturers’ association – stay well ahead of the curve.

“All of the Swedish textile machinery companies are doing really well in major markets such as Europe, China, India and the USA,” says TMAS Secretary General Therese Premler-Andersson. “They are now gathering forces to prepare for the most important show – ITMA 2019 in Barcelona in June. I expect to see new players and partnerships as we enter the industry 4.0 era for real. We are ready to display an even higher degree of the real time monitoring of processes, automation, flexible customisation, and the incorporation of robots into production lines.  Our customers expect a lot of in terms of knowledge and our ability to customise and offer turnkey solutions.”

A focus on customer service, aligned with the drive to constantly innovate, has long ensured that the member companies of TMAS – the Swedish texile machinery manufacturers’ association – stay well ahead of the curve.

“All of the Swedish textile machinery companies are doing really well in major markets such as Europe, China, India and the USA,” says TMAS Secretary General Therese Premler-Andersson. “They are now gathering forces to prepare for the most important show – ITMA 2019 in Barcelona in June. I expect to see new players and partnerships as we enter the industry 4.0 era for real. We are ready to display an even higher degree of the real time monitoring of processes, automation, flexible customisation, and the incorporation of robots into production lines.  Our customers expect a lot of in terms of knowledge and our ability to customise and offer turnkey solutions.”

The forward-looking attitude of the Swedish companies is perhaps best summed up by Reimar Westerlind, the owner, since 1961, of ACG Gruppen.
At the age of 90, Reimar still travels to his office every day to oversee the operations of the diverse companies operating under the ACG umbrella.
“Everything now is about automation and digitisation,” he says. “We have to be on that track or we will be lost – innovate or die.”

Robotics
One ACG Gruppen company moving rapidly forward with new innovations in this area is ACG Kinna, which at ITMA 2019 will be providing dramatic live demonstrations of its new robotic pillow filling system.
This has the ability to fill and finish some 3,840 pillows per eight-hour shift, which is a considerable improvement on what is currently possible with existing systems, resulting in significant savings in both labour and energy for busy home textile businesses.

At ITMA 2019, Eton will be demonstrating a complete material handling solution with advanced software providing real-time information covering every aspect of the process.
“Our systems are a natural fit with the major Industry 4.0 networked manufacturing plants that are now being constructed worldwide for sectors such as the garment and home textiles manufacturing and automotive industries,” says Eton’s Sales and Commercial Director Roger Ryrlén.

Sensors
Advanced senor developments are playing a large part in moving many areas of the textile industry forward too.
Eltex of Sweden, for example, is achieving considerable success with its yarn fault detection and tension monitoring systems across a range of sectors, including the tufting of carpets, the creeling of woven materials and even the production of woven reinforcements for the composites industry.

At successive ITMA shows, IRO AB has also consistently introduced new milestones in the field of yarn feeding technology for weaving machines, and ITMA 2019 will be no exception.
“Following significant investment in our R&D capabilities, we have been making great progress in further boosting the efficiency and performance of our expanding X3 range,” says IRO AB Managing Director and Chairman of TMAS Mikael Äremann. “I can’t remember a time since the 1980s when we had so many new innovations to unveil at an ITMA, and I’m greatly looking forward to the positive response to them we are anticipating in Barcelona this June.”

Resource savings
ITMA 2019 will meanwhile see the launch of TexCoat G4 – the next generation of Baldwin Technology’s non-contact precision application system for fabric finishing. The TexCoat G4 enables a continuously high-quality and productive textile finishing process with zero chemistry waste and minimised water and energy consumption.
The non-contact spray technology brings a range of advantages including single or double-sided application,  the elimination of Foulard bath contamination, low wet pick-up levels leading to the elimination of drying steps, zero chemistry waste in changeovers of chemistry, colour or fabric, and the possibility of batch reporting, visibility of pad loading, chemical usage etc.

Other TMAS companies exhibiting in Barcelona include Texo AB, whose wide-width weaving looms make the belts for machines on which half of the world’s paper is made, ES-Automatex, which specialises in bespoke automation concepts and Svegea, a company leading the field in a number colarette machines and cutting and slitting equipment.

“At the last ITMA in 2015 in Milan, there was much talk about Industry 4.0 technologies but certainly from the perspective of TMAS, ITMA 2019 will be the place for concrete solutions as to how data and the new tools we have available can be exploited to the full,” says Therese Premler-Andersson. “There is already much more networking between the companies, with software very much the enabler and common interfaces bringing ideas closer together. We are greatly looking forward to further exchanges of ideas when meeting with customers old and new in Barcelona.”

More information:
TMAS ITMA 2019
Source:

Issued on behalf of TMAS by AWOL Media.