From the Sector

Reset
16 results
Manfred Hackl, CEO der EREMA Group Copyright: Erema Group
Manfred Hackl, CEO der EREMA Group
03.08.2023

Lindner & Erema gründen gemeinsame Holding

Erema Group und die Lindner Holding gründen gemeinsam die Holding BLUEONE Solutions, um die Expertise aus beiden Unternehmen zu bündeln und durch gemeinsame Forschungsprojekte Branchenstandards im Kunststoffrecycling zu schaffen.

Vom Abfall bis hin zum recycelten Granulat durchlaufen potentielle neue Rohstoffe mehrere unterschiedliche Recyclingprozesse. Diese reichen vom Sortieren, dem Zerkleinern, Waschen und Trocknen bis hin zur Extrusion inkl. Filtrierung, Compoundierung sowie Geruchsoptimierung.

In der optimalen Feinabstimmung der einzelnen Recyclingschritte liegt die Herausforderung der Branche – insbesondere, wenn Energieeffizienz und hohe Rezyklatqualitäten erreicht werden sollen. Mit der Gründung von BLUEONE Solutions, einem Unternehmen an dem die Erema Group und die Lindner Holding jeweils 50 % halten und in die Anteile der Lindner Washtech eingebracht wurden, soll da angesetzt werden. Durch Abstimmungs- und Optimierungsprozesse sowie durch neue gemeinsame Forschungsprojekte, wird die Wertschöpfungstiefe deutlich erhöht und neue Branchenstandards gesetzt.

Erema Group und die Lindner Holding gründen gemeinsam die Holding BLUEONE Solutions, um die Expertise aus beiden Unternehmen zu bündeln und durch gemeinsame Forschungsprojekte Branchenstandards im Kunststoffrecycling zu schaffen.

Vom Abfall bis hin zum recycelten Granulat durchlaufen potentielle neue Rohstoffe mehrere unterschiedliche Recyclingprozesse. Diese reichen vom Sortieren, dem Zerkleinern, Waschen und Trocknen bis hin zur Extrusion inkl. Filtrierung, Compoundierung sowie Geruchsoptimierung.

In der optimalen Feinabstimmung der einzelnen Recyclingschritte liegt die Herausforderung der Branche – insbesondere, wenn Energieeffizienz und hohe Rezyklatqualitäten erreicht werden sollen. Mit der Gründung von BLUEONE Solutions, einem Unternehmen an dem die Erema Group und die Lindner Holding jeweils 50 % halten und in die Anteile der Lindner Washtech eingebracht wurden, soll da angesetzt werden. Durch Abstimmungs- und Optimierungsprozesse sowie durch neue gemeinsame Forschungsprojekte, wird die Wertschöpfungstiefe deutlich erhöht und neue Branchenstandards gesetzt.

Die Erema Group ist seit 40 Jahren im Kunststoffrecycling tätig und gilt als der Marktführer im Bereich der Extrusion. Lindner, seit 75 Jahren Qualitätshersteller von Schreddern und Recyclinganlagen für die Abfallwirtschaft, ist mit der Marke Lindner Washtech seit 10 Jahren als Waschanlagen-Spezialist weltweit präsent. Gemeinsame Forschungsprojekte, wie beispielsweise die Versuchsanlagen in der LIT Factory an der Johannes-Kepler-Universität (JKU) Linz, haben die Firmen bereits vor Jahren in einen intensiven fachlichen Austausch treten lassen.

Optimierung der Recyclingprozesse
Mit der Gründung von BLUEONE Solutions liegt der Fokus auf der Weiterentwicklung des Kunststoffrecyclings. Lindner bringt die Erfahrung im Aufbereiten von Abfallströmen und die Expertise im Waschen und Erema das Know-how im Bereich Extrudieren und Filtrieren mit ein. Synergien sollen genutzt und die Optimierungen des Gesamtkreislaufes ermöglicht werden.
„Essenziell für eine funktionierende Recyclingwirtschaft wird sein, dass die gesamte Prozess- bzw. Wertschöpfungskette – von der Abfallsammlung und Aufbereitung über das Recycling bis hin zum Kunststoff-Endprodukt – im Fokus der agierenden Unternehmen steht. Durch diesen Firmenzusammenschluss schaffen Erema und Lindner ein besseres Gesamtverständnis, um dadurch speziell im Polyolefinebereich die erforderliche Weiterentwicklung gemeinsam zu prägen“, erklärt Manfred Hackl, CEO der EREMA Group. „Im Detail betrachtet, können der Recyclingextruder, die vorgeschaltete Waschanlage sowie Materialhandling optimal aufeinander abgestimmt werden, so dass Qualitätsstandards bestmöglich erfüllt und Energiekosten optimiert werden können – dank prozessübergreifender Steuerung & Monitoring, gestützt durch digitale Lösungen. In Zukunft werden wir perfekt abgestimmte All-in-one-Lösungen anbieten, die es unseren Kunden ermöglichen, ein Gesamtpaket zu kaufen, das exakt auf ihre Anwendungen abgestimmt ist.“

More information:
EREMA EREMA Group Lindner Recycling
Source:

EREMA Group GmbH

(c) EREMA
Manfred Hackl, CEO EREMA Group and Markus Huber-Lindinger, Managing Director EREMA, open the EREMA Discovery Day 2023
09.06.2023

EREMA Discovery Day as meeting place for plastics and recycling industry

On June 1, EREMA hosted the EREMA Discovery Day focusing on the post consumer segment from a European perspective. Live demonstrations showcased the latest machine innovations for PET and polyolefin recycling.

The invitation was accepted by around 400 customers and partners, mainly from Europe, to find out about the wide range of recycling technologies for PO and PET plastic waste. The technology that was presented and explained by EREMA experts and guest speakers during lectures in the morning, could then be seen live in-action in the afternoon when the recycling machines were demonstrated in operation. A total of six innovative recycling technologies were on display: INTAREMA® TVEplus® DuaFil® Compact, INTAREMA® TVEplus® RegrindPro® + ReFresher, the COREMA® cascade extrusion system, a VACUREMA® Inline Sheet line equipped with new EcoGentle technology, the new INTAREMA® FibrePro:IV machine, and the PCU-
TwinScrew. These allowed visitors to witness their performance and the high quality of recycled pellets that they produce.

On June 1, EREMA hosted the EREMA Discovery Day focusing on the post consumer segment from a European perspective. Live demonstrations showcased the latest machine innovations for PET and polyolefin recycling.

The invitation was accepted by around 400 customers and partners, mainly from Europe, to find out about the wide range of recycling technologies for PO and PET plastic waste. The technology that was presented and explained by EREMA experts and guest speakers during lectures in the morning, could then be seen live in-action in the afternoon when the recycling machines were demonstrated in operation. A total of six innovative recycling technologies were on display: INTAREMA® TVEplus® DuaFil® Compact, INTAREMA® TVEplus® RegrindPro® + ReFresher, the COREMA® cascade extrusion system, a VACUREMA® Inline Sheet line equipped with new EcoGentle technology, the new INTAREMA® FibrePro:IV machine, and the PCU-
TwinScrew. These allowed visitors to witness their performance and the high quality of recycled pellets that they produce.

"This wide range of technologies is necessary because the recycling process each of our customers choose depends on the type of plastic, the level of contamination of the input material, and which product will be made using the recycled pellets. Following the expansion of our Ansfelden site and with the new site nearby in St. Marien, we can now demonstrate all these processes, carry out test runs with customers' material and focus on development work independently of our Customer Centre," says EREMA's Managing Director Markus Huber-Lindinger.

EREMA is driving forward research and development work in the company's new R&D Centre. Two halls with a total area of 1,550 square metres and a new office building offering space for 50 workplaces has been built. Here, the company bundles cross-departmental test machines and laboratory facilities for post consumer and inhouse recycling applications. R&D is decentralised at EREMA. Employees from different departments handle process engineering challenges, innovations in mechanical engineering and automation technology - all with the aim of meeting customer requirements and achieving the highest possible quality of recycled pellets.  

On the evening before Discovery Day, EREMA celebrated its 40th anniversary together with customers and partners. A review covered the company's history - from the first workshop in a garage in 1983, to its position today as a innovation pioneer and one of the market leaders.

More information:
EREMA plastics Recycling
Source:

EREMA Group

(c) EREMA
07.06.2023

EREMA presents a new solution for PET fibre-to-fibre recycling

Following their entry into the fibres and textiles sector, as announced at K 2022, recycling machine manufacturer EREMA launches the INTAREMA® FibrePro:IV - which has been specially developed for PET fibre-to-fibre recycling - at ITMA in Milan from June 8 to 14. Thanks to its especially gentle material preparation and efficient removal of spinning oils, the rPET produced can be reused in proportions of up to 100 percent for the production of very fine fibres.

Following their entry into the fibres and textiles sector, as announced at K 2022, recycling machine manufacturer EREMA launches the INTAREMA® FibrePro:IV - which has been specially developed for PET fibre-to-fibre recycling - at ITMA in Milan from June 8 to 14. Thanks to its especially gentle material preparation and efficient removal of spinning oils, the rPET produced can be reused in proportions of up to 100 percent for the production of very fine fibres.

PET is regarded as a key material for the production of synthetic fibres. Around two thirds of the total volume of PET goes into the production of PET fibres for the textile industry. This highlights the importance of high-quality recycling solutions for the circular economy. By combining proven INTAREMA® technology with a new IV optimiser, EREMA succeeds in processing shredded PET fibre materials heavily contaminated by spinning oils in such a way that the finest fibres can be produced again from the recycled pellets. The system, which now joins EREMA's machine portfolio as the INTAREMA® FibrePro:IV, is characterised by a longer residence time of the PET melt. This is an essential factor for achieving high quality recycled pellets, as it allows the spinning oils and other additives used to improve the handling of the fibres during manufacturing to be removed more efficiently than in conventional PET recycling processes. Following extrusion, by polycondensation the intrinsic viscosity (IV) of the PET melt is increased in the new IV optimiser and under high vacuum to the precise level that is needed for fibre production. "Including filtration the output quality that we achieve with this recycling process is so high that ultra-fine fibres of up to 2 dtex can be produced using these rPET pellets, with an rPET content of 100 percent," says Markus Huber-Lindinger, Managing Director at EREMA. Waste PET fibre from production processes can therefore be further processed into rPET filament fibre, carpet yarn and staple fibre.

While the focus of the fibre and textiles application is currently still on PET fibre recycling, EREMA is committed to driving forward the recycling of mixed fibre materials from classic textile recycling collection in a next project phase. In order to accelerate development work, the EREMA Group opened its own fibre test centre, where a cross-company team is working on recycling solutions for fibre-to-fibre applications. The centre also operates a fully equipped and variable industrial-scale recycling plant. It includes the peripheral technology required and is available to customers for trials.

More information:
EREMA ITMA Fibers Recycling
Source:

EREMA Group

(c) EREMA
Manfred Hackl, CEO EREMA Group GmbH
17.05.2023

EREMA: Manfred Hackl is Plastics Recycling Ambassador of the Year

Manfred Hackl, CEO of EREMA Group GmbH, was recently awarded the accolade Plastics Recycling Ambassador of the Year at the Plastics Recycling Show Europe. The award is given in honour of personalities who are particularly committed to plastics recycling.
 
Manfred Hackl has been with EREMA since 1995 and, prior to joining the management team, was responsible for the product development and market launch of VACUREMA technology that closed the loop in the bottle-to-bottle segment efficiently and cost effectively. In his current role as CEO of the EREMA Group and in various roles in well-known national and international associations he promotes plastics recycling and circular economy across the industry, regionally and throughout Europe - especially at EU level - encouraging everybody in the industry to work together.

Manfred Hackl, CEO of EREMA Group GmbH, was recently awarded the accolade Plastics Recycling Ambassador of the Year at the Plastics Recycling Show Europe. The award is given in honour of personalities who are particularly committed to plastics recycling.
 
Manfred Hackl has been with EREMA since 1995 and, prior to joining the management team, was responsible for the product development and market launch of VACUREMA technology that closed the loop in the bottle-to-bottle segment efficiently and cost effectively. In his current role as CEO of the EREMA Group and in various roles in well-known national and international associations he promotes plastics recycling and circular economy across the industry, regionally and throughout Europe - especially at EU level - encouraging everybody in the industry to work together.

"I dedicate the Recycling Ambassador of the Year award to the employees at the EREMA Group. This year we are celebrating our 40th anniversary, and this award, just like the many we have received for our technologies over the years, shows that we can be very proud of what we have accomplished and achieved together during this time," says Manfred Hackl, delighted with the award. In the past business year 2022/23 alone, the extruders supplied by the companies within the EREMA Group deliver an additional 1.6 million tonnes of recycling capacity.

Source:

EREMA Group GmbH

Photo: EREMA/Wakolbinger
Manfred Hackl, CEO EREMA Group GmbH
28.04.2023

EREMA Group ends financial year 2022/23

Around EUR 355 million in overall turnover, 350 extruders delivered creating an additional recycling capacity for 1.6 million tons of recycled pellets as a result - these are the figures with which the EREMA Group was able to close the 2022/23 financial year in March.

"With demand for recycled plastics remaining high, the past financial year brought many challenges that we needed to handle," says Manfred Hackl, CEO of EREMA Group GmbH. The challenges included persistent delays in the supply chain and unexpected supplier outages. Logistics and production processes had to be adapted several times as a result. The situation has improved significantly meantime as a result of these measures and more stable supply chains.

Around EUR 355 million in overall turnover, 350 extruders delivered creating an additional recycling capacity for 1.6 million tons of recycled pellets as a result - these are the figures with which the EREMA Group was able to close the 2022/23 financial year in March.

"With demand for recycled plastics remaining high, the past financial year brought many challenges that we needed to handle," says Manfred Hackl, CEO of EREMA Group GmbH. The challenges included persistent delays in the supply chain and unexpected supplier outages. Logistics and production processes had to be adapted several times as a result. The situation has improved significantly meantime as a result of these measures and more stable supply chains.

The production locations in Austria manufactured 270 extruders and delivered them to customers around the globe. Taking the whole group into consideration, this figure rises to 350 including the extruders from PLASMAC, the Italian subsidiary. The recycled pellet production capacity of all extrusion systems delivered in financial year 2022/23 adds up to around 1.6 million tonnes per year. On top of that there are around 130 additional components and modules such as filter systems and ReFresher anti-odour units.

Recycling innovations for high-quality pellets
K 2022 - the highlight trade fair of the past financial year - saw the EREMA Group launch seven
new recycling systems and components. These included the new INTAREMA® TVEplus® DuaFil® Compact recycling system and the EcoGentle® plasticising unit, which was also newly developed. Thanks to their gentle polymer treatment and significantly lower melt temperature, both extrusion innovations deliver effective advantages in terms of the quality of the melt, recycled pellets, and final product, as well as impressive energy efficiency in post consumer and PET recycling applications. The significance of these innovations for plastics recycling is underlined by the nomination of the DuaFil® Compact technology for one of this year's Plastics Recycling Awards Europe in the category Recycling Machinery Innovation of the Year.
The same applies to the READYMAC 1109 TVE machine made to stock by EREMA Group subsidiary UMAC, as well as to the new ALPHA XS edge trim recycling machine for the inhouse recycling segment made by PLASMAC. The market launch of the deinking system presented at K 2022 by the EREMA Group company KEYCYCLE delivering a throughput of 1,200 kilograms per hour has been a success, as has the commissioning of a further unit sold to a film manufacturer.

40 years of EREMA
The beginning of the new financial year falls almost to the day on EREMA's 40th anniversary. On 14 April 1983, Helmut Bacher, Helmuth Schulz and Georg Wendelin founded EREMA Engineering Recycling Maschinen und Anlagen GesmbH, laying the foundation for the 40-year success story. In celebration, the comapny will hold the event EREMA Discovery Day at the company headquarters on the 1st of June. This event with live insights into the latest post consumer and PET recycling technologies will also see the official opening of the newly built research and development centre.

Source:

EREMA Group GmbH

Photo: EREMA
21.10.2022

EREMA: Circular economy for PET fibres

The textile industry is the third largest consumer of plastics. While growth rates in the production of fibres and textiles are high, the circular economy has hardly become established in this segment. The EREMA Group is now intensifying development of recycling solutions for this application with their new fibres and textiles business unit. Currently, the focus is on PET fibre materials from fibre production and subsequent processing steps. Technologies for recycling mixed fibre textiles from textile collection sources are to follow in a follow-up project phase.

The textile industry is the third largest consumer of plastics. While growth rates in the production of fibres and textiles are high, the circular economy has hardly become established in this segment. The EREMA Group is now intensifying development of recycling solutions for this application with their new fibres and textiles business unit. Currently, the focus is on PET fibre materials from fibre production and subsequent processing steps. Technologies for recycling mixed fibre textiles from textile collection sources are to follow in a follow-up project phase.

"With EREMA's VACUREMA® and INTAREMA® technology and PURE LOOP's ISEC evo technology, our company group already has an extensive range of machines for fibre and PET recycling applications. For ecologically and economically sound recycling, however, new technological solutions are needed to use the recycled fibres in higher-value end applications and to achieve a functioning circular economy," explains Wolfgang Hermann, Business Development Manager Application Fibres & Textiles, EREMA Group GmbH. The initial focus will be on PET, regarded as a key material for the production of synthetic fibres. The aim is to find recycling solutions that allow PET fibre materials to be prepared for reuse in PET fibre production processes. This is a significant step for the circular economy because PET fibres in textiles account for about two-thirds of the total volume of PET.

In this development work, the EREMA Group can build on existing know-how. Proven recycling technologies have been combined with a new IV optimiser. "This extends the residence time of the PET melt, which is particularly necessary in fibre recycling to efficiently remove spinning oils. Our recycling process also increases the IV value of the PET melt after extrusion back to the specific level that is essential for production of the fibre," explains Hermann. Waste PET fibre from production processes can therefore be further processed into rPET filament fibre, carpet yarn and staple fibre.

Fibre test centre with plant to test customers' materials
In order to accelerate development work, EREMA opened its own fibre test centre a few months ago, where a cross-company team is working on recycling solutions for fibre-to-fibre applications.

Source:

EREMA Gruppe

(c) PURE LOOP
07.09.2022

PURE LOOP: High-strength synthetic nonwoven made with a recycled content of 10 percent

Geosynthetics have become an indispensable part of the construction industry. PP nonwovens, for example - mechanically bonded continuous fibres made from specially UV-stabilised polypropylenes - are often used in blanket form as barriers, screens and filters, and their strength extends the service life of construction projects. Whether for road construction, or as barrier on glaciers or against weeds - there are myriad applications.

TenCate Geosynthetics uses the PURE LOOP ISEC evo technology to recycle this type of PP nonwoven. The European company, with locations in Austria, France and the Netherlands, is specialised in the development and production of geotextiles for modern civil engineering applications. The edge trimmings and production rejects generated during manufacturing used to be recycled at the Linz site, but not fed back into the company's own production process.

Geosynthetics have become an indispensable part of the construction industry. PP nonwovens, for example - mechanically bonded continuous fibres made from specially UV-stabilised polypropylenes - are often used in blanket form as barriers, screens and filters, and their strength extends the service life of construction projects. Whether for road construction, or as barrier on glaciers or against weeds - there are myriad applications.

TenCate Geosynthetics uses the PURE LOOP ISEC evo technology to recycle this type of PP nonwoven. The European company, with locations in Austria, France and the Netherlands, is specialised in the development and production of geotextiles for modern civil engineering applications. The edge trimmings and production rejects generated during manufacturing used to be recycled at the Linz site, but not fed back into the company's own production process.

"The demands on us were high," recalls Patrick Wiesinger, project manager at PURE LOOP. "The PP nonwoven is highly tear resistant, which means its a very challenging recycling process. Our ISEC evo machine conserves the quality of the production waste really well during recycling, so we were able to achieve the specified increase in quality for the recyclates."

Another advantage of PURE LOOP technology is the wide range of shapes in which the production scrap can be delivered for processing. "Our ifeed technology with double feed ram system and singleshaft shredder offers the ideal conditions for direct processing of these large rolls - and without the need for prior preparation of the input material by employees before the material is fed into the recycling process", emphasizes Patrick Wiesinger. With the ISEC evo recycling machine TenCate can now manufacture its high-strength PP nonwoven product with a recyclate content of up to 10 percent.

Source:

PURE LOOP, EREMA Group GmbH

28.06.2022

EREMA Gruppe and Borealis: K 2022 preview

On June 13, EREMA Group and Borealis invited representatives of the international plastics and recycling trade press to Upper Austria for a sneak preview of the technological developments and lighthouse projects that the companies will present at K 2022, the plastics industry's international meeting place. The venue for the pre-K event was EREMA Group headquarters in Ansfelden.

On June 13, EREMA Group and Borealis invited representatives of the international plastics and recycling trade press to Upper Austria for a sneak preview of the technological developments and lighthouse projects that the companies will present at K 2022, the plastics industry's international meeting place. The venue for the pre-K event was EREMA Group headquarters in Ansfelden.

EREMA Group K 2022 preview
In Düsseldorf, the subsidiaries of the EREMA Group - which are EREMA, PURE LOOP, UMAC, 3S, KEYCYCLE and PLASMAC - will present their technological innovations, services and support together at a Group trade fair stand for the first time. Seven new recycling systems and components will be presented that enable large-scale plants with a production capacity of up to 6 t/h while setting a milestone in recyclate quality and process stability. This is made possible by technological innovations in the plasticizing unit that have been specially developed for high throughputs with low specific energy consumption, the new EREMA 406 laser filter with a 50 percent larger screening area, and new digital assistance systems that will be launched at K 2022 and made available on the BluPort® customer platform. These include, for example, the PredictOn app, which helps to anticipate and eliminate imminent malfunctions based on continuous measurement and evaluation of machine data.

New series of machines for new target groups
For customers looking for rapidly available recycling systems for simple applications, EREMA Group subsidiary UMAC has an innovation in store for K 2022. The company, which has so far specialised in refurbishing and trading in previously owned equipment, is expanding its business area and in Düsseldorf will launch READYMAC, a standardised, prefabricated recycling solution that can be produced from stock, based on proven EREMA TVE technology.

Finally, in the inhouse recycling segment, PURE LOOP and PLASMAC will round off the wide range of machines offered by the group of companies with their product portfolio.

Live recycling and lighthouse projects at the Circonomic Center
In the outdoor area of the K show, EREMA will bring plastics recycling to life with live demonstrations in conjunction with cooperation partners. Different waste streams are processed for this purpose. The wide variety of high-quality applications for recyclate will be showcased in the "products made of recyclate" exhibition, ranging from technical components to consumer goods and food packaging.

Borealis – accelerating the transition towards a more circular future
Borealis is committed to using their expertise and global reach to advance the circular economy of plastics. At the joint Pre-K 2022 kick-off on June 13, Borealis provided a preview of their integrated way of circular thinking and featured topics and activities at the K Fair 2022 in October. The preview covered new technologies and innovations including new packaging and infrastructure applications of the Bornewables™ portfolio of circular polyolefin products, manufactured with renewable feedstocks. New applications for Design for Recyclability, Re-Use, chemical recycling and advanced mechanical recycling were also on display.

Source:

EREMA Group GmbH

22.06.2022

EREMA: POWERFIL presents new laserfilter

POWERFIL, a business unit of recycling machine manufacturer EREMA GmbH, presents its 2/406 laserfilter.

"For applications with a focus on melt quality and filtration fineness, this increase in screen area ensures lower pressure and temperature at the same throughput rate, allowing even finer screens to be used for even better results in quality-intensive plastics applications," explains Robert Obermayr, Head of Business Unit POWERFIL, EREMA GmbH. If the throughput capacity of the recycling plant needs to be increased, a significantly higher rate of plastic melt can be filtered while maintaining the other parameters thanks to the larger surface area of the screen. Up to 9,000 kilogrammes of melt can be filtered per hour with the Quattro version of the new LF 406 laserfilter.

POWERFIL, a business unit of recycling machine manufacturer EREMA GmbH, presents its 2/406 laserfilter.

"For applications with a focus on melt quality and filtration fineness, this increase in screen area ensures lower pressure and temperature at the same throughput rate, allowing even finer screens to be used for even better results in quality-intensive plastics applications," explains Robert Obermayr, Head of Business Unit POWERFIL, EREMA GmbH. If the throughput capacity of the recycling plant needs to be increased, a significantly higher rate of plastic melt can be filtered while maintaining the other parameters thanks to the larger surface area of the screen. Up to 9,000 kilogrammes of melt can be filtered per hour with the Quattro version of the new LF 406 laserfilter.

"Plastic recycling has become a must-have, even for input streams with higher levels of contamination. Efficient filtration systems are therefore indispensable for achieving the specified melt quality using existing extrusion systems," says Obermayr. That is why POWERFIL also offers the proven EREMA melt filters as individual components for existing EREMA machines and third-party extrusion systems. The product range includes the SW RTF partial area backflush system and the laserfilter. The range is aimed at manufacturers as well as recyclers, because the high-performance filters can be used to process post consumer plastics as well as post industrial films with paper labels and clean PET material. Both types of filter are particularly easy to integrate into an existing recycling plant and both are available in numerous sizes and variations. Whether the customer uses the robust backflush filter or the continuous high-performance laserfilter depends on the throughput and level of contamination of the material. The Laserfilter is ideal for heavy contamination. It handles impurity levels up to 5 percent and filtration as fine as 70 μm while continuously cleaning the screen with a scraper.

POWERFIL will also present the new 2/406 laserfilter and the full range of filters at the K 2022 trade fair stand for the EREMA Group.

More information:
EREMA Recycling plastics
Source:

EREMA Group GmbH

(c) plasticpreneur
Shredder, injection moulding unit and extruder
22.06.2022

EREMA Group acquires stake in start-up company plasticpreneur®

As of 30 May 2022, EREMA Group GmbH acquired 19.8 percent of plasticpreneur® gmbh. plasticpreneur® is an Austrian start-up company founded two years ago that manufactures at its production site in Klagenfurt recycling solutions for plastic waste that are mobile and can be operated without prior knowledge. The machine portfolio covers the recycling process and the production of new end-products. Due to it´s wide range of applications, it is in demand both in the Global South and in industrialised countries.

In the two years since the company was founded, plasticpreneur® has already sold 330 machines to customers in over 70 countries on all continents. In addition, they have made over 750 application-specific moulds, many of them custom-built to comply with individual customer specifications.

As of 30 May 2022, EREMA Group GmbH acquired 19.8 percent of plasticpreneur® gmbh. plasticpreneur® is an Austrian start-up company founded two years ago that manufactures at its production site in Klagenfurt recycling solutions for plastic waste that are mobile and can be operated without prior knowledge. The machine portfolio covers the recycling process and the production of new end-products. Due to it´s wide range of applications, it is in demand both in the Global South and in industrialised countries.

In the two years since the company was founded, plasticpreneur® has already sold 330 machines to customers in over 70 countries on all continents. In addition, they have made over 750 application-specific moulds, many of them custom-built to comply with individual customer specifications.

While plastics recycling has gained enormous momentum in the industrialised countries, more remote and poorer regions of the world have hardly benefited from high-tech solutions for industrial recycling processes so far. They are held back by a lack of infrastructure and know-how. That is why waste is often incinerated or disposed of in landfills, rivers and the surrounding environment. "Our mission - Another life for plastic, because we care - is also aimed at supporting these regions with solutions for plastic recycling, and with plasticpreneur® we have found the ideal partner for this," says Manfred Hackl, CEO EREMA Group.

The start-up company's machines can process HDPE, PP, PS, LDPE, PLA, AB and TPU separately. Their product range includes a shredder, injection moulding unit, extruder unit for the production of end products, air filters as well as custom-built moulds. "For our machines to be used in regions with little infrastructure, they must be easy to operate without prior knowledge. The fact that we also develop end-product solutions needed locally makes our range of services particularly attractive here," explains Sören Lex, CEO and co-founder of plasticpreneur®. As soon as recycling also becomes a source of income for the operators, they become entrepreneurs. That explains the name of the start-up, a word created from "plastic" and "entrepreneur". plasticpreneur® customers in these countries include e.g. social enterprises and operators of refugee camps, where everyday consumer goods - from clothes pegs and school supplies to toys and fence posts - are produced and sold using plastic waste. This means that the added value stays local.

The demand for plasticpreneur® machines is also increasing in industrialised countries. On the one hand by educational institutions and organisations that use them to raise awareness of the need for a circular economy in workshops and to give pupils as well as adults a better understanding of plastic recycling. On the other hand by customers who are developing new end-products for plastic waste together with plasticpreneur®. Because the machines are so easy to operate they enable a low-theshold use of recycled plastics in product development processes, starting from generating prototypes to launchin small series production. Small companies, product designers and developers therefore are another steadily growing customer segment.

Source:

EREMA Group GmbH

26.05.2022

EREMA Group: Growing revenues, plant sizes and production capacities

The EREMA Group, which comprises EREMA Group GmbH and its subsidiaries EREMA, PURE LOOP, UMAC, 3S, KEYCYCLE and PLASMAC, closed the 2021/22 financial year with a 17 percent increase in revenue. Consolidated Group revenue amounted to EUR 295 million, and the number of employees increased to over 840. The EREMA Group remains on course for continued growth.

A closer look at the post consumer segment clearly shows a trend towards larger plants, both for PET recycling and for processing polyolefins. For example, the first VACUREMA® Basic 2628 T machine with an annual capacity of up to 40,000 tonnes was recently commissioned at a customer's site in Brazil. This plant features a ten-meter-long special geometry screw with a diameter of 280 millimetres and a weight of 3.5 tonnes. The screw was developed and manufactured by 3S, a subsidiary of EREMA GmbH.

The EREMA Group, which comprises EREMA Group GmbH and its subsidiaries EREMA, PURE LOOP, UMAC, 3S, KEYCYCLE and PLASMAC, closed the 2021/22 financial year with a 17 percent increase in revenue. Consolidated Group revenue amounted to EUR 295 million, and the number of employees increased to over 840. The EREMA Group remains on course for continued growth.

A closer look at the post consumer segment clearly shows a trend towards larger plants, both for PET recycling and for processing polyolefins. For example, the first VACUREMA® Basic 2628 T machine with an annual capacity of up to 40,000 tonnes was recently commissioned at a customer's site in Brazil. This plant features a ten-meter-long special geometry screw with a diameter of 280 millimetres and a weight of 3.5 tonnes. The screw was developed and manufactured by 3S, a subsidiary of EREMA GmbH.

Demand for previously-owned machines at UMAC also remained high during the past financial year. In addition to the general trend towards plastics recycling, the decisive factor here is that customers are more frequently opting for previously-owned systems available at short notice due to the tense situation on the procurement markets. At the same time, businesses that have so far had little contact with recycling are also becoming increasingly interested in this topic. Their need for feasibility studies, consulting and engineering services, project management and turnkey projects are now also very successfully catered for by KEYCYCLE, an EREMA Group company. KEYCYCLE has also acquired from Cadel Deinking the patent, technology and distribution rights for an innovative ink removal technology, which is now being further developed using the know-how of the EREMA Group and shaped into a product that meets industrial standards.

The initiative launched four years ago to modernise and expand existing EREMA Group sites was continued during the past financial year with the expansion and construction of a dedicated machine demonstration centre for PLASMAC in Milan. Equipped with additional production floor space and new and enlarged customer centres, all companies within the group are now well prepared to meet rising demand, and with the new research and development centre under construction in Ansfelden, the framework for further outstanding plastics recycling milestones from EREMA is currently being optimised.

Source:

EREMA Group GmbH

Georg Wendelin Foto: privat
Georg Wendelin
05.04.2022

EREMA mourns the passing of company co-founder Georg Wendelin

The EREMA Group mourns the passing of Georg Wendelin, company co-founder, former Managing Partner and long-time Chairman of the Supervisory Board of EREMA Group GmbH, who died on the 29th of March at the age of 84.

In 1983, at a time when plastics recycling was hardly an issue, Georg Wendelin, together with Helmut Bacher and Helmuth Schulz, laid the corner stone for the group of companies that today is a world market leader by founding the company and building the first EREMA plastics recycling machine. With pioneering spirit, a business acumen and his respectful and appreciative management style, Georg Wendelin actively shaped the success of the company, attentively and proudly keeping track of how plastics recycling went from being a niche to a trend and how the EREMA Group became a driving force behind the circular economy. In 2019, he was awarded the Golden Decoration of the Republic of Austria in recognition of his work.

The EREMA Group mourns the passing of Georg Wendelin, company co-founder, former Managing Partner and long-time Chairman of the Supervisory Board of EREMA Group GmbH, who died on the 29th of March at the age of 84.

In 1983, at a time when plastics recycling was hardly an issue, Georg Wendelin, together with Helmut Bacher and Helmuth Schulz, laid the corner stone for the group of companies that today is a world market leader by founding the company and building the first EREMA plastics recycling machine. With pioneering spirit, a business acumen and his respectful and appreciative management style, Georg Wendelin actively shaped the success of the company, attentively and proudly keeping track of how plastics recycling went from being a niche to a trend and how the EREMA Group became a driving force behind the circular economy. In 2019, he was awarded the Golden Decoration of the Republic of Austria in recognition of his work.

"We will greatly miss Georg Wendelin as a personality who was closely associated with us for all these years. Because of his humanity, he was a highly respected figure of leadership on all sides," said Manfred Hackl, CEO of EREMA Group GmbH and himself a long-time companion of Wendelin's.

More information:
EREMA Georg Wendelin
Source:

EREMA Group GmbH

(c) EREMA Group GmbH
17.03.2022

EREMA: Working together with Recycling Company Anviplas

The Spanish recycling company Anviplas has been involved in plastics recycling for more than 30 years, during which time it has built up extensive know-how that now benefits customers throughout Europe, in Africa and in Asia. Their cooperation with EREMA is almost as long. Since 1991, Anviplas has relied on the technology and service provided by the Austrian recycling machine manufacturer.

The Spanish recycling company Anviplas has been involved in plastics recycling for more than 30 years, during which time it has built up extensive know-how that now benefits customers throughout Europe, in Africa and in Asia. Their cooperation with EREMA is almost as long. Since 1991, Anviplas has relied on the technology and service provided by the Austrian recycling machine manufacturer.

Employing 64 people, Anviplas recycles post-industrial and post-consumer plastic waste, especially HD and LD-PE as well as PP, to make recycled pellets in all colour variations. The production capacity is 1,800 tonnes per month. An EREMA type INTAREMA® 1716 TVEplus® recycling machine with screen changer is in operation at the site in Navarcles (Barcelona) for processing the PP material stream. This patented extruder system was developed for handling difficult-to-process materials, such as heavily printed films as well as very moist waste. This machine is characterised by its optimised 3-stage degassing system; firstly by preheating and predrying the material in the preconditioning unit, secondly because the screw design allows reverse degassing, and thirdly in the degassing zone of the extruder.

Anviplas customers manufacture a huge bandwidth of products made using their recycled pellets. They range from various film products, such as stretch, shrink, mulch and silage films, to irrigation, corrugated and high-pressure pipes, as well as containers such as tubs, bottles, barrels and crates.

In February 2022 the Repeats Group, a pan-European platform for LDPE recycling, and Anviplas announced, that Repeats has made an investment in the Spanish recycling company. For Repeats this investment in Anviplas represents an important step in building a pan-European plastics recycling platform.

More information:
EREMA Recycling plastics Anviplas
Source:

EREMA Group GmbH

(c) EREMA Group GmbH
26.01.2022

EREMA: From reserve site to production plant in just a few months

Just under a year ago, the EREMA Group started to repurpose the premises of Gruber & Kaja in St. Marien, which they took over as a reserve site in January 2021. In the meantime, a lot is going on there.

"When this site came up for sale, it only took us a few days to decide to buy the 40,000m² plot, including the workshop hall, which has an area of 15,000m²," says Manfred Hackl, CEO of EREMA Group GmbH. Around EUR 20 million was invested in the purchase, as the site offered the opportunity to increase production capacity by 60 percent in the immediate vicinity of the company headquarters in Ansfelden.

The fact that this site is now already being used so intensively was not envisaged at the time, because at the end of 2020 the company was just completing the expansion to their headquarters in Ansfelden, involving an investment of around EUR 17 million. 20 new jobs have already been created as a result, with a further 30 to follow in the next few months. By the time the new site is completed, the total number of new jobs will be up to 150.

Just under a year ago, the EREMA Group started to repurpose the premises of Gruber & Kaja in St. Marien, which they took over as a reserve site in January 2021. In the meantime, a lot is going on there.

"When this site came up for sale, it only took us a few days to decide to buy the 40,000m² plot, including the workshop hall, which has an area of 15,000m²," says Manfred Hackl, CEO of EREMA Group GmbH. Around EUR 20 million was invested in the purchase, as the site offered the opportunity to increase production capacity by 60 percent in the immediate vicinity of the company headquarters in Ansfelden.

The fact that this site is now already being used so intensively was not envisaged at the time, because at the end of 2020 the company was just completing the expansion to their headquarters in Ansfelden, involving an investment of around EUR 17 million. 20 new jobs have already been created as a result, with a further 30 to follow in the next few months. By the time the new site is completed, the total number of new jobs will be up to 150.

This development is due to the high demand for the EREMA Group's plastics recycling technologies and the trend towards ever-larger recycling plants. "Just in December, we delivered a VACUREMA® system to Brazil that will produce up to 40,000 metric tonnes of recycled PET (rPET) per year. That is equivalent to recycling around 1.1 billion 1.5-litre PET bottles. This site provides the perfect conditions for building this scale of machine," says Hackl.

Markus Achleitner, Upper Austria's Minister for the Economy, was also impressed by this development during his visit to St. Marien. "There is hardly any other region in the world that focuses as closely on materials expertise and the circular economy as in Upper Austria. We want to fully exploit this potential with our #upperVISION2030 business and research strategy. EREMA is an important driver in this industry. It makes me all the more pleased that the company owners have once again confirmed their commitment to Upper Austria as a business location, to the circular economy and to the employees by developing this site," says Achleitner. "This investment is an important positive signal for the entire region of Upper Austria location, especially in the current challenging times, and all the more so for creating 150 jobs," he emphasises.

New site milestones
Since January 2021, part of the existing office and hall space at Kunststoffstraße 1, as the site's address is now called, has been occupied by companies and departments of the EREMA Group. UMAC GmbH, a subsidiary specialising in servicing and trading previously owned recycling machines, which was severely short of space at its main location in Styria, moved its entire production and administration to St. Marien. Large areas of hall storage space were adapted for both UMAC and EREMA GmbH. The paint shop was also relocated from Ansfelden to St. Marien, and another hall was equipped for building large-scale VACUREMA® systems - these are systems used all over the world to recycle PET bottles. Production in this workshop is now being ramped up step by step.
Space that is not being used in St. Marien over the medium-term will be rented out. An industry-related firm has already moved in, and another 300 m² of office space is currently still available.

More information:
EREMA plastics Recycling
Source:

EREMA Group GmbH

(c) AMUT/EREMA
02.12.2021

AMUT/EREMA: From PET bottles straight to food contact grade r-PET packaging

AMUT’s strategic partnership with EREMA contributes to accelerate the transition towards a greener world.  In summer 2021, EREMA in collaboration with AMUT  has finalized the installation and commissioning of ALTO packaging ́s first extrusion line for food grade PET sheets in New Zealand market. At the ALTO Plastic Packaging site, in Albany, the plant now processes 100 % washed post-
consumer flakes into 100 % food contact grade monolayer thermoforming sheet. In New Zealand, this milestone represents the first system to be installed for this special application.

The plastic packaging company ALTO, a division of PACT Group, invested for this new food grade PET sheet extrusion line as a part of Pact Group ́s vision to lead Circular Economy through Packaging in Australia and New Zealand.

AMUT’s strategic partnership with EREMA contributes to accelerate the transition towards a greener world.  In summer 2021, EREMA in collaboration with AMUT  has finalized the installation and commissioning of ALTO packaging ́s first extrusion line for food grade PET sheets in New Zealand market. At the ALTO Plastic Packaging site, in Albany, the plant now processes 100 % washed post-
consumer flakes into 100 % food contact grade monolayer thermoforming sheet. In New Zealand, this milestone represents the first system to be installed for this special application.

The plastic packaging company ALTO, a division of PACT Group, invested for this new food grade PET sheet extrusion line as a part of Pact Group ́s vision to lead Circular Economy through Packaging in Australia and New Zealand.

Thanks to the direct combination of VACUREMA® PET recycling technology and the AMUT Inline Sheet production technology there is no longer any extra process stage. This is, because the melt goes straight from the VACUREMA® 1716 T Basic to the AMUT plant without the detour of pelletising. The post-consumer PET material is already decontaminated and pre-dried prior to extrusion in the vacuum reactor of the VACUREMA® Basic, with a throughput of up to 1,500 kg per hour. After high capacity filtration by EREMA SW-RTF backflush filter and online IV measurement, the melt goes directly into the AMUT Inline Sheet plant where it is processed into thermoforming sheet from 0.15 mm till 1.2 mm thickness. The monolayer thermoforming sheet produced from pure rPET is not only 100 % food contact compliant, it also fulfils the FDA and further regulations. At ALTO it is further processed into trays and food containers.

AMUT played its part by providing a full range of downstream equipment ranging from the Automatic Tdie, three rolls stack calender with automatic gap control and motorized cross axing unit, lamination unit for welding and barrier films, thickness control gauge to anti-static silicon coating unit, fully automatic two shafts turret winder and in line edge trims grinding and recycling.

The special features of this extrusion line come from the complete automatic and easy management of the line. This is due to the new Amut`s software including the Easy Start and Easy Change functions that will allow the operator to start the extrusion line and change product formats in automatic mode.

EREMA and AMUT are long-term partners in the Inline Sheet sector. EREMA ́s VACUREMA® technology is currently in use in more than 100 Inline Sheet facilities around the world, also for PACT Group companies in Australia. 

More information:
AMUT EREMA PET plastics Recycling
Source:

EREMA Group GmbH

(c) EREMA Group GmbH
11.11.2021

EREMA awarded for the Recycling Machinery Innovation of the Year

EREMA is winner at this year´s Plastics Recycling Awards Europe. At the award ceremony as part of the Plastics Recycling Show Europe at 5th November in Amsterdam, EREMA was awarded for its recycling system INTAREMA® TVEplus® RegrindPro® + ReFresher in the category Recycling Machinery Innovation of the Year. Thanks to the combination of its recycling machine with the ReFresher technology that reduces odour downstream of the extrusion process, EREMA has enabled the PCR-HDPE produced with it to be used in proportions of up to 100 percent for the production of packaging for direct contact with food and beverages, as confirmed by the U.S. Food and Drug Administration (FDA).

The judges recongised this innovation as a step change in eliminating unwanted odour from waste plastics, allowing recyclate to replace virgin palstics in high end applications. This type of innovation is essential for meeting EU targets for recycled content of food contact plastics.
The market also confirms awarding this technology. By the end of 2021, EREMA customers will produce 450,000 tonnes of high-quality, odor-optimized regranulate per year, with it.

EREMA is winner at this year´s Plastics Recycling Awards Europe. At the award ceremony as part of the Plastics Recycling Show Europe at 5th November in Amsterdam, EREMA was awarded for its recycling system INTAREMA® TVEplus® RegrindPro® + ReFresher in the category Recycling Machinery Innovation of the Year. Thanks to the combination of its recycling machine with the ReFresher technology that reduces odour downstream of the extrusion process, EREMA has enabled the PCR-HDPE produced with it to be used in proportions of up to 100 percent for the production of packaging for direct contact with food and beverages, as confirmed by the U.S. Food and Drug Administration (FDA).

The judges recongised this innovation as a step change in eliminating unwanted odour from waste plastics, allowing recyclate to replace virgin palstics in high end applications. This type of innovation is essential for meeting EU targets for recycled content of food contact plastics.
The market also confirms awarding this technology. By the end of 2021, EREMA customers will produce 450,000 tonnes of high-quality, odor-optimized regranulate per year, with it.

More information:
EREMA Recycling
Source:

EREMA Group GmbH