From the Sector

Reset
12 results
(c) EREMA
07.06.2023

EREMA presents a new solution for PET fibre-to-fibre recycling

Following their entry into the fibres and textiles sector, as announced at K 2022, recycling machine manufacturer EREMA launches the INTAREMA® FibrePro:IV - which has been specially developed for PET fibre-to-fibre recycling - at ITMA in Milan from June 8 to 14. Thanks to its especially gentle material preparation and efficient removal of spinning oils, the rPET produced can be reused in proportions of up to 100 percent for the production of very fine fibres.

Following their entry into the fibres and textiles sector, as announced at K 2022, recycling machine manufacturer EREMA launches the INTAREMA® FibrePro:IV - which has been specially developed for PET fibre-to-fibre recycling - at ITMA in Milan from June 8 to 14. Thanks to its especially gentle material preparation and efficient removal of spinning oils, the rPET produced can be reused in proportions of up to 100 percent for the production of very fine fibres.

PET is regarded as a key material for the production of synthetic fibres. Around two thirds of the total volume of PET goes into the production of PET fibres for the textile industry. This highlights the importance of high-quality recycling solutions for the circular economy. By combining proven INTAREMA® technology with a new IV optimiser, EREMA succeeds in processing shredded PET fibre materials heavily contaminated by spinning oils in such a way that the finest fibres can be produced again from the recycled pellets. The system, which now joins EREMA's machine portfolio as the INTAREMA® FibrePro:IV, is characterised by a longer residence time of the PET melt. This is an essential factor for achieving high quality recycled pellets, as it allows the spinning oils and other additives used to improve the handling of the fibres during manufacturing to be removed more efficiently than in conventional PET recycling processes. Following extrusion, by polycondensation the intrinsic viscosity (IV) of the PET melt is increased in the new IV optimiser and under high vacuum to the precise level that is needed for fibre production. "Including filtration the output quality that we achieve with this recycling process is so high that ultra-fine fibres of up to 2 dtex can be produced using these rPET pellets, with an rPET content of 100 percent," says Markus Huber-Lindinger, Managing Director at EREMA. Waste PET fibre from production processes can therefore be further processed into rPET filament fibre, carpet yarn and staple fibre.

While the focus of the fibre and textiles application is currently still on PET fibre recycling, EREMA is committed to driving forward the recycling of mixed fibre materials from classic textile recycling collection in a next project phase. In order to accelerate development work, the EREMA Group opened its own fibre test centre, where a cross-company team is working on recycling solutions for fibre-to-fibre applications. The centre also operates a fully equipped and variable industrial-scale recycling plant. It includes the peripheral technology required and is available to customers for trials.

More information:
EREMA ITMA Fibers Recycling
Source:

EREMA Group

Photo: EREMA/Wakolbinger
Manfred Hackl, CEO EREMA Group GmbH
28.04.2023

EREMA Group ends financial year 2022/23

Around EUR 355 million in overall turnover, 350 extruders delivered creating an additional recycling capacity for 1.6 million tons of recycled pellets as a result - these are the figures with which the EREMA Group was able to close the 2022/23 financial year in March.

"With demand for recycled plastics remaining high, the past financial year brought many challenges that we needed to handle," says Manfred Hackl, CEO of EREMA Group GmbH. The challenges included persistent delays in the supply chain and unexpected supplier outages. Logistics and production processes had to be adapted several times as a result. The situation has improved significantly meantime as a result of these measures and more stable supply chains.

Around EUR 355 million in overall turnover, 350 extruders delivered creating an additional recycling capacity for 1.6 million tons of recycled pellets as a result - these are the figures with which the EREMA Group was able to close the 2022/23 financial year in March.

"With demand for recycled plastics remaining high, the past financial year brought many challenges that we needed to handle," says Manfred Hackl, CEO of EREMA Group GmbH. The challenges included persistent delays in the supply chain and unexpected supplier outages. Logistics and production processes had to be adapted several times as a result. The situation has improved significantly meantime as a result of these measures and more stable supply chains.

The production locations in Austria manufactured 270 extruders and delivered them to customers around the globe. Taking the whole group into consideration, this figure rises to 350 including the extruders from PLASMAC, the Italian subsidiary. The recycled pellet production capacity of all extrusion systems delivered in financial year 2022/23 adds up to around 1.6 million tonnes per year. On top of that there are around 130 additional components and modules such as filter systems and ReFresher anti-odour units.

Recycling innovations for high-quality pellets
K 2022 - the highlight trade fair of the past financial year - saw the EREMA Group launch seven
new recycling systems and components. These included the new INTAREMA® TVEplus® DuaFil® Compact recycling system and the EcoGentle® plasticising unit, which was also newly developed. Thanks to their gentle polymer treatment and significantly lower melt temperature, both extrusion innovations deliver effective advantages in terms of the quality of the melt, recycled pellets, and final product, as well as impressive energy efficiency in post consumer and PET recycling applications. The significance of these innovations for plastics recycling is underlined by the nomination of the DuaFil® Compact technology for one of this year's Plastics Recycling Awards Europe in the category Recycling Machinery Innovation of the Year.
The same applies to the READYMAC 1109 TVE machine made to stock by EREMA Group subsidiary UMAC, as well as to the new ALPHA XS edge trim recycling machine for the inhouse recycling segment made by PLASMAC. The market launch of the deinking system presented at K 2022 by the EREMA Group company KEYCYCLE delivering a throughput of 1,200 kilograms per hour has been a success, as has the commissioning of a further unit sold to a film manufacturer.

40 years of EREMA
The beginning of the new financial year falls almost to the day on EREMA's 40th anniversary. On 14 April 1983, Helmut Bacher, Helmuth Schulz and Georg Wendelin founded EREMA Engineering Recycling Maschinen und Anlagen GesmbH, laying the foundation for the 40-year success story. In celebration, the comapny will hold the event EREMA Discovery Day at the company headquarters on the 1st of June. This event with live insights into the latest post consumer and PET recycling technologies will also see the official opening of the newly built research and development centre.

Source:

EREMA Group GmbH

08.11.2022

Ascend buys majority stake in recycler Circular Polymers

Ascend Performance Materials has purchased a majority stake in California-based Circular Polymers, a recycler of post-consumer, high-performance polymers including polyamide 6 and 66, polypropylene and polyester (PET). The deal provides Ascend with a consistent supply of high-quality PCR materials for its ReDefyne™ sustainable polyamides, launched at K 2022.

Circular Polymers, which as part of the deal is renamed Circular Polymers by Ascend, reclaims and processes post-consumer carpet via a unique technology and has redirected approximately 85 million pounds of waste from landfills into new goods since 2018.

“We are focused on helping our customers reach their sustainability goals and Circular Polymers by Ascend provides materials that offer strong performance with a considerably smaller environmental footprint, compared to other technologies like pyrolysis,” said Phil McDivitt, president and CEO of Ascend. “Since we launched ReDefyne, the demand for our circular products has been significant across all segments of our business, including automotive, consumer, electronics and high-performance fibers and textiles.”

Ascend Performance Materials has purchased a majority stake in California-based Circular Polymers, a recycler of post-consumer, high-performance polymers including polyamide 6 and 66, polypropylene and polyester (PET). The deal provides Ascend with a consistent supply of high-quality PCR materials for its ReDefyne™ sustainable polyamides, launched at K 2022.

Circular Polymers, which as part of the deal is renamed Circular Polymers by Ascend, reclaims and processes post-consumer carpet via a unique technology and has redirected approximately 85 million pounds of waste from landfills into new goods since 2018.

“We are focused on helping our customers reach their sustainability goals and Circular Polymers by Ascend provides materials that offer strong performance with a considerably smaller environmental footprint, compared to other technologies like pyrolysis,” said Phil McDivitt, president and CEO of Ascend. “Since we launched ReDefyne, the demand for our circular products has been significant across all segments of our business, including automotive, consumer, electronics and high-performance fibers and textiles.”

Ascend has a sustainability strategy based on three pillars: empowering people, innovating solutions and operating without compromise. Ascend has committed to reducing its greenhouse gas emissions by 80% by 2030 and recently announced two new efforts to reduce the carbon footprint of its products.

Source:

Ascend Performance Materials / EMG

04.11.2022

Rieter publishes Investor Update 2022

  • Sales of CHF 366.8 million in the third quarter, CHF 987.4 million after nine months
  • Order intake of CHF 226.4 million in the third quarter, CHF 1 095.8 million after nine months
  • Order backlog of around CHF 2 000 million as of September 30, 2022
  • Precautionary measures taken against potential energy crisis in Europe
  • Financing of a Professorship for Artificial Intelligence
  • Rieter site sales process on schedule
  • Outlook 2022

Rieter recorded a significant increase in sales in the third quarter of 2022, reaching a level of CHF 366.8 million (2021: CHF 257.3 million). The measures introduced to increase sales and profitability in the second half of 2022 are taking effect and will continue to be implemented in a systematic manner. These include a close cooperation with key suppliers, the development of alternative solutions to eliminate material shortages, the enforcement of price increases, and the improvement of the margin quality of the order backlog.

  • Sales of CHF 366.8 million in the third quarter, CHF 987.4 million after nine months
  • Order intake of CHF 226.4 million in the third quarter, CHF 1 095.8 million after nine months
  • Order backlog of around CHF 2 000 million as of September 30, 2022
  • Precautionary measures taken against potential energy crisis in Europe
  • Financing of a Professorship for Artificial Intelligence
  • Rieter site sales process on schedule
  • Outlook 2022

Rieter recorded a significant increase in sales in the third quarter of 2022, reaching a level of CHF 366.8 million (2021: CHF 257.3 million). The measures introduced to increase sales and profitability in the second half of 2022 are taking effect and will continue to be implemented in a systematic manner. These include a close cooperation with key suppliers, the development of alternative solutions to eliminate material shortages, the enforcement of price increases, and the improvement of the margin quality of the order backlog.

The order intake of CHF 226.4 million in the third quarter of 2022 reflects the expected normalization of demand for new equipment compared to the record year of 2021, which was characterized by catch-up effects and the regional shift in demand. In addition, the well-known uncertainties and risks and the continuing extremely long delivery times at key manufacturers had a dampening effect on demand. Due to the slowdown in capacity utilization in the spinning mills, demand for consumables, wear & tear and spare parts also declined in the third quarter of 2022. Major orders continued to be recorded from Turkey, Uzbekistan, and China.

Rieter has a high order backlog of around CHF 2 000 million as of September 30, 2022 (September 30, 2021: CHF 1 562 million), which will guarantee capacity utilization in all three business groups until well into 2023 or rather 2024. The cancellation rate in the reporting period was around 5% of the order backlog.

Outlook 2022
Rieter anticipates weakened demand for new systems in the coming months. The demand for consumables, wear & tear and spare parts will depend on the capacity utilization of spinning mills in the months ahead.

For the full year 2022, Rieter expects sales of around CHF 1 400 million. The realization of sales revenue from the order backlog continues to be associated with risks in relation to the well-known uncertainties.

Despite significantly higher sales compared to the prior-year period, Rieter expects EBIT and net result for 2022 to be below the previous year’s level. This is due to the considerable increases in the cost of materials and logistics, additional costs for compensation of material shortages as well as expenses in connection with the acquisition in the years 2021/2022.

More information:
Rieter financial year 2022
Source:

Rieter Management AG

Photo: Reifenhäuser
26.10.2022

Reifenhäuser Extrusion Systems and maku AG cooperate

  • Strategic partnership for automation system in the field of slot dies and coextrusion adapters

Reifenhäuser Extrusion Systems (RES) - the Reifenhäuser Group's business unit specializing in extrusion components - announces a strategic partnership with maku AG at K 2022, the world's largest plastics trade fair. The aim of the cooperation is the joint marketing and further development of the automation system designed by maku for coextrusion adapters and slot dies.

  • Strategic partnership for automation system in the field of slot dies and coextrusion adapters

Reifenhäuser Extrusion Systems (RES) - the Reifenhäuser Group's business unit specializing in extrusion components - announces a strategic partnership with maku AG at K 2022, the world's largest plastics trade fair. The aim of the cooperation is the joint marketing and further development of the automation system designed by maku for coextrusion adapters and slot dies.

The so-called PAM system (precise, autonomous, mechatronic) is available immediately and exclusively as an automation option for new Reifenhäuser dies and adapters, as well as for aftermarket dies across all manufacturers. PAM enables producers in the field of flat film and sheet production as well as extrusion coating to precisely control the entire hot part (coextrusion adapter and die) via the line's control panel. This is significantly faster and more accurate than conventional control by hand or expansion bolt automation. It enables faster start-up of good production, higher output with lower energy consumption, and thus significantly improved overall equipment efficiency (OEE). The decisive advantage lies in the use of motorized manual adjustment bolts that replace conventional thermal expansion bolts. Reifenhäuser presented the system for the first time at the K 2022.

Source:

Reifenhäuser GmbH & Co. KG Maschinenfabrik
 

VacuFil® Foto: Oerlikon
VacuFil®
13.10.2022

Oerlikon auf der K 2022

  • Nachhaltige Lösungen für die gesamte Kette

Unter dem Motto „Feel the Flow. Keep Control.” präsentiert sich die Division Polymer Processing Solutions des Schweizer Oerlikon Konzerns auf der K 2022. Die internationale Leitmesse für die Kunststoffindustrie findet vom 19. bis 26. Oktober in Düsseldorf, Deutschland, statt. Es werden rund 200.000 Besucher erwartet. Oerlikon informiert über ein breit gefächertes Leistungsangebot im Bereich der Kunststoffherstellung und -verarbeitung. Innovative Lösungen und Technologien zu den Themen: Rohstoffaufbereitung dank moderner Polykondensations- und Extrusionsanlagen, neueste Recyclingtechnologien, effiziente Heißkanalsysteme, innovative Beschichtungslösungen, nachhaltige Herstellungsverfahren für Filtrationsanwendungen und hochqualitative Zahnradpumpen.

  • Nachhaltige Lösungen für die gesamte Kette

Unter dem Motto „Feel the Flow. Keep Control.” präsentiert sich die Division Polymer Processing Solutions des Schweizer Oerlikon Konzerns auf der K 2022. Die internationale Leitmesse für die Kunststoffindustrie findet vom 19. bis 26. Oktober in Düsseldorf, Deutschland, statt. Es werden rund 200.000 Besucher erwartet. Oerlikon informiert über ein breit gefächertes Leistungsangebot im Bereich der Kunststoffherstellung und -verarbeitung. Innovative Lösungen und Technologien zu den Themen: Rohstoffaufbereitung dank moderner Polykondensations- und Extrusionsanlagen, neueste Recyclingtechnologien, effiziente Heißkanalsysteme, innovative Beschichtungslösungen, nachhaltige Herstellungsverfahren für Filtrationsanwendungen und hochqualitative Zahnradpumpen.

Modernste Anlagen für das Recycling von Kunststoffen
Oerlikons Joint Venture Unternehmen BBEngineering beschäftigt sich seit Jahren mit dem Thema Recycling und setzt damit in diesem Jahr auf der Düsseldorfer Messe einen Schwerpunkt. Neben Extrudern, Filtern und Mischern bietet BBEngineering mit VacuFil® eine komplette Anlage für ein innovatives und einzigartiges PET LSP-Recyclingverfahren an. VacuFil® vereint schonende Großfiltration und gezielte IV-Regulierung für eine konstant hervorragende rPET-Schmelzequalität. Das modulare System kann für verschiedene Recyclinganwendungen eingesetzt werden.

Source:

Oerlikon

(c) Borealis
08.09.2022

Borealis and Trexel develop fully recyclable lightweight bottle

  • Monomaterial solution contains renewably-sourced polypropylene from the Bornewables™ portfolio of circular polyolefins
  • Trexel employs its proprietary MuCell® technology to deliver a range of lightweighting benefits
  • EverMinds™ in action: reuse and design for recycling are focus of value chain collaboration

Borealis and Trexel, an expert in foaming injection and blow moulded parts, announce that they have co-developed a new plastic bottle based on a grade from the Bornewables™ portfolio of polyolefins made using renewable feedstocks derived 100% from waste and residue streams. The lightweight bottle – which will be showcased at the Borealis stand at the K 2022 (from 19 to 26 October 2022 in Düsseldorf) – is reusable and fully recyclable. It boasts a significantly lower overall CO2 footprint because it is composed of renewably-sourced feedstock and produced in the foaming process.

  • Monomaterial solution contains renewably-sourced polypropylene from the Bornewables™ portfolio of circular polyolefins
  • Trexel employs its proprietary MuCell® technology to deliver a range of lightweighting benefits
  • EverMinds™ in action: reuse and design for recycling are focus of value chain collaboration

Borealis and Trexel, an expert in foaming injection and blow moulded parts, announce that they have co-developed a new plastic bottle based on a grade from the Bornewables™ portfolio of polyolefins made using renewable feedstocks derived 100% from waste and residue streams. The lightweight bottle – which will be showcased at the Borealis stand at the K 2022 (from 19 to 26 October 2022 in Düsseldorf) – is reusable and fully recyclable. It boasts a significantly lower overall CO2 footprint because it is composed of renewably-sourced feedstock and produced in the foaming process.

The Bornewables™ portfolio of circular polyolefins helps reduce the carbon footprint while offering material performance equal to virgin polymers. Using Bornewables grades allows for design freedom and colour flexibility, and helps retain a premium look and feel. The grades – which are commercially available in Europe – help conserve natural resources because they are derived solely from waste and residue streams, for example from used cooking oil. Reusing waste already in circulation instead of fossil fuel-based feedstocks enhances the sustainability of applications made using the Bornewables grades.

The reusable new bottle developed by Borealis and Trexel retains its value over many life cycles thanks to the use of Trexel’s proprietary technology in tandem with Bornewables grades; as a material solution, the new bottle minimises the use of valuable raw materials. Moreover, converters consume less energy in the production process when using the MuCell® technology. The bottle thus helps close the loop on plastics circularity by way of design for recycling, the use of renewable feedstocks, and excellent material performance across multiple life cycles.

Source:

Borealis

(c) Freudenberg
25.08.2022

Freudenberg at Fachpack 2022

Freudenberg Performance Materials (Freudenberg) is presenting its sustainable Evolon® product range for reusable technical packaging for highly-sensitive parts at Fachpack 2022 in Nuremberg, Germany from September 27-29. The microfilament textiles offer improved surface protection for molded plastic parts, painted parts and so-called class A parts, thus providing customers with significant savings potential.

Evolon® RE is the most sustainable product in the portfolio. It contains the highest percentage of recycled PET and has a smaller carbon footprint. The new Ultra Force range from Evolon® offers extremely high mechanical strength and eliminates the need for PVC in the transportation and protection of large, heavy parts. Freudenberg has developed the ESD range (electro-static discharge range) for the packaging of sensitive electronic components: it offers permanent electro-static discharging and its surface resistivity can be customized.

Freudenberg Performance Materials (Freudenberg) is presenting its sustainable Evolon® product range for reusable technical packaging for highly-sensitive parts at Fachpack 2022 in Nuremberg, Germany from September 27-29. The microfilament textiles offer improved surface protection for molded plastic parts, painted parts and so-called class A parts, thus providing customers with significant savings potential.

Evolon® RE is the most sustainable product in the portfolio. It contains the highest percentage of recycled PET and has a smaller carbon footprint. The new Ultra Force range from Evolon® offers extremely high mechanical strength and eliminates the need for PVC in the transportation and protection of large, heavy parts. Freudenberg has developed the ESD range (electro-static discharge range) for the packaging of sensitive electronic components: it offers permanent electro-static discharging and its surface resistivity can be customized.

Source:

Freudenberg Performance Materials Holding SE & Co. KG

(c) Sappi Europe
25.07.2022

Sappi showcases its solutions at FACHPACK 2022

The FACHPACK in Nuremberg ranks among the most important packaging industry gatherings. From 27 to 29 September 2022, Sappi will be presenting its latest products and solutions for functional paper packaging, flexible packaging papers, label papers, containerboard and paperboard. The company is focusing its efforts on sustainable, recyclable and innovative solutions.

The FACHPACK in Nuremberg ranks among the most important packaging industry gatherings. From 27 to 29 September 2022, Sappi will be presenting its latest products and solutions for functional paper packaging, flexible packaging papers, label papers, containerboard and paperboard. The company is focusing its efforts on sustainable, recyclable and innovative solutions.

  • Wide range of barrier papers in the market for sustainable and recyclable packaging solutions
  • High-impact brand presence in corrugated board packaging thanks to Fusion Nature Plus in combination with Fusion Topliner
  • Parade Label Pro wet-glue label paper for an efficient operation and an excellent visual impression

Wide range of barrier papers
Sappi’s ultimate goal as a specialist in barrier papers is to replace non-recyclable aluminium and plastic multi-layer laminates through the introduction of truly sustainable alternatives that meet all market requirements in terms of performance and recycling. Sappi is continuously expanding its portfolio of barrier papers. At the show, Sappi will be showcasing several examples of food and non-food applications using these barrier papers.

A smooth surface and a high degree of whiteness: Parade Label Pro
Sappi will also be presenting its new, non-wet-strength wet-glue label paper Parade Label Pro – featuring samples from all over the world. This glossy, double-coated quality paper offers a smooth surface plus a high degree of whiteness. It’s suitable for numerous label and flexible packaging applications, such as labels for disposable bottles, food and non-food containers as well as wrappers for a variety of products. It can be printed in offset, flexo and gravure, and finished with hot foil and blind embossing, for example.

Brand presentation that appeals to the senses
“For manufacturers of branded goods, it is becoming increasingly important to convey brand values and product characteristics in a way that is emotionally appealing and that really sets the stage,” explains Luis Mata, Sales Director Packaging of Sappi Europe. At the FACHPACK, Sappi will also be presenting its containerboard products for corrugated board applications, which, with their brilliant colour reproduction, enhance on-shelf product impact and ensure real brand differentiation.

Sappi’s popular Algro Design paperboard portfolio also allows the design scope and leeway to communicate brand values in an emotionally appealing way.

Source:

Sappi Europe

28.06.2022

EREMA Gruppe and Borealis: K 2022 preview

On June 13, EREMA Group and Borealis invited representatives of the international plastics and recycling trade press to Upper Austria for a sneak preview of the technological developments and lighthouse projects that the companies will present at K 2022, the plastics industry's international meeting place. The venue for the pre-K event was EREMA Group headquarters in Ansfelden.

On June 13, EREMA Group and Borealis invited representatives of the international plastics and recycling trade press to Upper Austria for a sneak preview of the technological developments and lighthouse projects that the companies will present at K 2022, the plastics industry's international meeting place. The venue for the pre-K event was EREMA Group headquarters in Ansfelden.

EREMA Group K 2022 preview
In Düsseldorf, the subsidiaries of the EREMA Group - which are EREMA, PURE LOOP, UMAC, 3S, KEYCYCLE and PLASMAC - will present their technological innovations, services and support together at a Group trade fair stand for the first time. Seven new recycling systems and components will be presented that enable large-scale plants with a production capacity of up to 6 t/h while setting a milestone in recyclate quality and process stability. This is made possible by technological innovations in the plasticizing unit that have been specially developed for high throughputs with low specific energy consumption, the new EREMA 406 laser filter with a 50 percent larger screening area, and new digital assistance systems that will be launched at K 2022 and made available on the BluPort® customer platform. These include, for example, the PredictOn app, which helps to anticipate and eliminate imminent malfunctions based on continuous measurement and evaluation of machine data.

New series of machines for new target groups
For customers looking for rapidly available recycling systems for simple applications, EREMA Group subsidiary UMAC has an innovation in store for K 2022. The company, which has so far specialised in refurbishing and trading in previously owned equipment, is expanding its business area and in Düsseldorf will launch READYMAC, a standardised, prefabricated recycling solution that can be produced from stock, based on proven EREMA TVE technology.

Finally, in the inhouse recycling segment, PURE LOOP and PLASMAC will round off the wide range of machines offered by the group of companies with their product portfolio.

Live recycling and lighthouse projects at the Circonomic Center
In the outdoor area of the K show, EREMA will bring plastics recycling to life with live demonstrations in conjunction with cooperation partners. Different waste streams are processed for this purpose. The wide variety of high-quality applications for recyclate will be showcased in the "products made of recyclate" exhibition, ranging from technical components to consumer goods and food packaging.

Borealis – accelerating the transition towards a more circular future
Borealis is committed to using their expertise and global reach to advance the circular economy of plastics. At the joint Pre-K 2022 kick-off on June 13, Borealis provided a preview of their integrated way of circular thinking and featured topics and activities at the K Fair 2022 in October. The preview covered new technologies and innovations including new packaging and infrastructure applications of the Bornewables™ portfolio of circular polyolefin products, manufactured with renewable feedstocks. New applications for Design for Recyclability, Re-Use, chemical recycling and advanced mechanical recycling were also on display.

Source:

EREMA Group GmbH

22.06.2022

EREMA: POWERFIL presents new laserfilter

POWERFIL, a business unit of recycling machine manufacturer EREMA GmbH, presents its 2/406 laserfilter.

"For applications with a focus on melt quality and filtration fineness, this increase in screen area ensures lower pressure and temperature at the same throughput rate, allowing even finer screens to be used for even better results in quality-intensive plastics applications," explains Robert Obermayr, Head of Business Unit POWERFIL, EREMA GmbH. If the throughput capacity of the recycling plant needs to be increased, a significantly higher rate of plastic melt can be filtered while maintaining the other parameters thanks to the larger surface area of the screen. Up to 9,000 kilogrammes of melt can be filtered per hour with the Quattro version of the new LF 406 laserfilter.

POWERFIL, a business unit of recycling machine manufacturer EREMA GmbH, presents its 2/406 laserfilter.

"For applications with a focus on melt quality and filtration fineness, this increase in screen area ensures lower pressure and temperature at the same throughput rate, allowing even finer screens to be used for even better results in quality-intensive plastics applications," explains Robert Obermayr, Head of Business Unit POWERFIL, EREMA GmbH. If the throughput capacity of the recycling plant needs to be increased, a significantly higher rate of plastic melt can be filtered while maintaining the other parameters thanks to the larger surface area of the screen. Up to 9,000 kilogrammes of melt can be filtered per hour with the Quattro version of the new LF 406 laserfilter.

"Plastic recycling has become a must-have, even for input streams with higher levels of contamination. Efficient filtration systems are therefore indispensable for achieving the specified melt quality using existing extrusion systems," says Obermayr. That is why POWERFIL also offers the proven EREMA melt filters as individual components for existing EREMA machines and third-party extrusion systems. The product range includes the SW RTF partial area backflush system and the laserfilter. The range is aimed at manufacturers as well as recyclers, because the high-performance filters can be used to process post consumer plastics as well as post industrial films with paper labels and clean PET material. Both types of filter are particularly easy to integrate into an existing recycling plant and both are available in numerous sizes and variations. Whether the customer uses the robust backflush filter or the continuous high-performance laserfilter depends on the throughput and level of contamination of the material. The Laserfilter is ideal for heavy contamination. It handles impurity levels up to 5 percent and filtration as fine as 70 μm while continuously cleaning the screen with a scraper.

POWERFIL will also present the new 2/406 laserfilter and the full range of filters at the K 2022 trade fair stand for the EREMA Group.

More information:
EREMA Recycling plastics
Source:

EREMA Group GmbH

20.06.2022

Reifenhäuser with solutions for films and nonwovens at K 2022

The Reifenhäuser Group will be represented with four booths at the world's leading trade fair for plastics processing, K 2022, from October 19 to 26. Under this year's Reifenhäuser motto "The Time is Now", the extrusion specialists will show producers of films and nonwovens solutions for the three major topics of the industry: sustainability, digitalization and productivity.

The main booth showcases the Reifenhäuser Blown Film, Cast Sheet Coating and Reicofil business units. With the help of machine exhibits, visual presentations and concrete solutions for end products, visitors will learn, among other things, how they can manufacture fully recyclable products economically, process recyclates safely, increase their output and network the entire production without becoming dependent on systems, specialists or manufacturers. To ensure smooth production even after purchase, Reifenhäuser Service shows how customers can get the best out of their Reifenhäuser products and increase their productivity with rework solutions, modifications, training programs and digital services.

The Reifenhäuser Group will be represented with four booths at the world's leading trade fair for plastics processing, K 2022, from October 19 to 26. Under this year's Reifenhäuser motto "The Time is Now", the extrusion specialists will show producers of films and nonwovens solutions for the three major topics of the industry: sustainability, digitalization and productivity.

The main booth showcases the Reifenhäuser Blown Film, Cast Sheet Coating and Reicofil business units. With the help of machine exhibits, visual presentations and concrete solutions for end products, visitors will learn, among other things, how they can manufacture fully recyclable products economically, process recyclates safely, increase their output and network the entire production without becoming dependent on systems, specialists or manufacturers. To ensure smooth production even after purchase, Reifenhäuser Service shows how customers can get the best out of their Reifenhäuser products and increase their productivity with rework solutions, modifications, training programs and digital services.

The component specialists of the Reifenhäuser Extrusion Systems business unit will additionally present their portfolio at two other exhibition booths. Here, everything revolves around screws, barrels and extruders - and why, especially for processing recycled material, high-performance wear protection is essential for reliability and high economic efficiency. Reifenhäuser Extrusion Systems will also showcase its innovations for flat dies and coextrusion blocks and their coordinated interaction for maximum productivity.

In addition to its own booths, Reifenhäuser will also be present as a partner of the R-Cycle initiative as part of a joint pavilion on the open-air site in the so-called Circular Economy Forum. R-Cycle is a cooperation project of various technology companies and organizations along the entire life cycle of plastic packaging.

Aanother highlight for visitors to the Reifenhäuser trade fair booths is the opportunity to additionally participate in the in-house exhibition on October 20, 21 and 24 at the Reifenhäuser Technology Center.

Source:

Reifenhäuser GmbH & Co. KG Maschinenfabrik