From the Sector

Reset
43 results
Graphic Toray
20.12.2023

Recycled carbon fiber: When a Boeing 787 turns into a Lenovo ThinkPad

Toray Industries, Inc. announced the successful development of recycled carbon fiber (rCF) derived from the production process of the Boeing 787 components using Toray’s advanced carbon fiber, TORAYCA™. The rCF, which is based on pyrolysis recycling process, has been integrated into the Lenovo ThinkPad X1 Carbon Gen 12 as reinforcement filler for thermoplastic pellets. Toray and Lenovo will continue to collaborate to expand the usage of rCF in other Lenovo products.

Toray rCF is the outcome of Boeing and Lenovo’s shared commitment to minimize their environmental impact. Boeing’s objective is to reduce solid waste going to landfill and produce recyclable materials, while Lenovo has been exploring materials to reduce the carbon footprint of their products. Toray rCF connects these visions by repurposing Toray’s high-performance carbon fiber from the Boeing aircraft production process into Lenovo’s ultra-light laptop PC.

Toray Industries, Inc. announced the successful development of recycled carbon fiber (rCF) derived from the production process of the Boeing 787 components using Toray’s advanced carbon fiber, TORAYCA™. The rCF, which is based on pyrolysis recycling process, has been integrated into the Lenovo ThinkPad X1 Carbon Gen 12 as reinforcement filler for thermoplastic pellets. Toray and Lenovo will continue to collaborate to expand the usage of rCF in other Lenovo products.

Toray rCF is the outcome of Boeing and Lenovo’s shared commitment to minimize their environmental impact. Boeing’s objective is to reduce solid waste going to landfill and produce recyclable materials, while Lenovo has been exploring materials to reduce the carbon footprint of their products. Toray rCF connects these visions by repurposing Toray’s high-performance carbon fiber from the Boeing aircraft production process into Lenovo’s ultra-light laptop PC.

TORAYCA™ is an established aerospace material known for its high strength, stiffness, and lightweighting properties. These qualities have led to its adoption in other applications such as electrical and electronic equipment housings, sports equipment, and other industrial applications.

A key advantage of carbon fiber is the ability to retain its primary mechanical properties even after the recycling process. Toray is actively advancing recycling technologies and establishing a strategic business model for rCF. Given that the carbon footprint of rCF is lower than that of virgin carbon fiber, Toray is proactively recommending the adoption of rCF to reduce the environmental impact of customers’ products. This commitment aligns with Toray’s dedication to fostering a circular economy, thereby reducing landfill waste.

Source:

Toray Industries

(c) AVK - Industrievereinigung Verstärkte Kunststoffe e. V.
14.11.2023

Successful SMCCreate 2023 Design Conference in Prague

Successful SMCCreate 2023 Design Conference in Prague

With over 60 participants from Europe and the USA the second edition of the SMCCreate Design Conference took place from November 7th to 8th in Prague. The conference was jointly organized by the AVK – Federation of Reinforced Plastics and the European Alliance for SMC BMC, promoting the use of SMC and providing design tools to designers for applying these versatile materials.

During the SMCCreate 2023 conference topics covered the wide spectrum of the design with fiber composite/composite components in SMC and BMC technology, from conceptual design, development, and scale-up, with a special emphasis on recycling and sustainability solutions. 18 speakers from various European countries showed how they address important market trends and changing customer needs, and which solutions their companies offered in terms of materials, performance and much more.

Successful SMCCreate 2023 Design Conference in Prague

With over 60 participants from Europe and the USA the second edition of the SMCCreate Design Conference took place from November 7th to 8th in Prague. The conference was jointly organized by the AVK – Federation of Reinforced Plastics and the European Alliance for SMC BMC, promoting the use of SMC and providing design tools to designers for applying these versatile materials.

During the SMCCreate 2023 conference topics covered the wide spectrum of the design with fiber composite/composite components in SMC and BMC technology, from conceptual design, development, and scale-up, with a special emphasis on recycling and sustainability solutions. 18 speakers from various European countries showed how they address important market trends and changing customer needs, and which solutions their companies offered in terms of materials, performance and much more.

As an introduction, speakers - including CTC/Airbus and Teijin - presented different possible applications for SMC and BMC components, including aircraft interiors, bicycle boxes, and applications in e-mobility. The topic of sustainability was broadly covered, highlighting recycling solutions and experiences (Siemens, IDI, OC, AOC), the use of renewable raw materials, as well new LCA models developed by the SMC BMC Alliance (LCS),

Specifically for designers, the use of the SMC flow and curing modelling was presented (ESI, OC), SMC positioning vs. aluminium (Spartners). The second day concluded with contributions on process optimization options for component production, including speeches by Dieffenbacher, Netzsch and EBG.

Source:

AVK - Industrievereinigung Verstärkte Kunststoffe e. V.

11.10.2023

Toray expands French Carbon Fiber Production Facilities

Toray Industries, Inc. will expand the French subsidiary Toray Carbon Fibers Europe S.A.’s production facilities for regular tow medium- and high-modulus carbon fibers (up to 24,000 filaments). This move will increase annual capacity at the Abidos plant (South-West France) from 5,000 metric tons annually, to 6,000 metric tons. Production is expected to start in 2025.

Demand for medium- and high-modulus carbon fibers is rising in Europe, driven by a push to move towards a net-zero society. This growth is mainly due to higher build rates for commercial aircrafts (secondary structures and engines), as well as centrifuge for energy production, satellites, and high-end automobiles. By boosting carbon fiber production capacity in Europe, Toray is responding to its customers’ demand for medium and high-modulus carbon fibers, as befits the market leader.

Toray Industries, Inc. will expand the French subsidiary Toray Carbon Fibers Europe S.A.’s production facilities for regular tow medium- and high-modulus carbon fibers (up to 24,000 filaments). This move will increase annual capacity at the Abidos plant (South-West France) from 5,000 metric tons annually, to 6,000 metric tons. Production is expected to start in 2025.

Demand for medium- and high-modulus carbon fibers is rising in Europe, driven by a push to move towards a net-zero society. This growth is mainly due to higher build rates for commercial aircrafts (secondary structures and engines), as well as centrifuge for energy production, satellites, and high-end automobiles. By boosting carbon fiber production capacity in Europe, Toray is responding to its customers’ demand for medium and high-modulus carbon fibers, as befits the market leader.

Source:

Toray Industries

05.10.2023

EURATEX and CIE warn EU Presidency about de-industrialised Europe

Ahead of the extra-ordinary Council on 6 October in Granada, EURATEX President, Alberto Paccanelli, and CIE President, Jose Vte Serna, call on the EU Presidency to develop a new competitiveness strategy, which can relaunch the European industry and ensure it will remain competitive in the decades to come. This means bringing together trade, energy, state aid and sustainability policies into a single, integrated, comprehensive approach, which can support a robust and modern European manufacturing industry.  
 
To consolidate a strong industrial structure in Europe, the Union should

Ahead of the extra-ordinary Council on 6 October in Granada, EURATEX President, Alberto Paccanelli, and CIE President, Jose Vte Serna, call on the EU Presidency to develop a new competitiveness strategy, which can relaunch the European industry and ensure it will remain competitive in the decades to come. This means bringing together trade, energy, state aid and sustainability policies into a single, integrated, comprehensive approach, which can support a robust and modern European manufacturing industry.  
 
To consolidate a strong industrial structure in Europe, the Union should

  1. secure the supply of clean energy at a competitive cost;
  2. support innovation and foster the necessary talent pool and
  3. be more assertive in achieving an international level-playing field on sustainability, based on the European model.  

During the past few years the implementation of incoherent and conflicting objectives under the trade, energy, industrial and sustainability policy has been observed. As a matter of fact, while the circular economy promised to be a recipe for a competitive industry of the future, the likelihood of pushing the EU industry out of the market and driving investment elsewhere than in Europe is very high. If this approach were to continue in the next years, it will result in a de-industrialised Europe, depending on imports from abroad. Such a Europe would be more exposed to geopolitical turmoil, with no agency to deliver its vision of peace, well-being and a healthy environment to its citizens.

It is fundamental for Europe to pursue a more coherent set of policies that put the competitiveness of its domestic industry at the core. In this context, all the industrial manufacturing sectors should be in the scope, including the textile industry, given its importance in providing essential products and applications to our society. A first impactful action that can be taken in this direction, would be to expand the scope of the Net-Zero Industry Act (NZIA) to include the textiles and clothing industry.
 
The history of European industry is fully woven in the birth and expansion of the European textiles industry since the XVIII century. Still today, the European textiles and clothing industry holds a pivotal position in the market, encompassing a diverse range of sectors and applications. In terms of employment, our industry creates 1,3 million direct jobs in Europe, encompassing a wide range of roles, from design and production to distribution and retail. European textiles have a wide range of applications, the most common one is of course clothing and fashion. The industry has a long history of producing high-quality apparel, with various regions specializing in specific niches.
 
Beyond clothing, there is a wide range of industrial sectors were textiles play an essential role, including  Automotive (used for upholstery, interior components, and even lightweight composite materials), Aircraft and Shipbuilding (where textiles are employed for their lightweight and high-strength properties, to enhance fuel efficiency, reduce emissions, and improve overall performance), Building and Construction (insulation, roofing, geotextiles, and architectural textiles), or Personal Protective Equipment, for medical personnel, firefighters, police and army officers. This includes masks, gowns, uniforms, helmets, and fire-resistant clothing, ensuring safety in hazardous environments.
 
Textiles are essential components of our society and our well-being. It is key for Europe to maintain its capacity to manufacture high-quality, sustainable and high-technology textiles.  With this in mind, the competitiveness policy of the future and the related funds to support it, should include the textile ecosystem in its scope.  

 

More information:
Euratex EU council Policy Hub
Source:

Euratex

ZwissTex integrates Kornit Technology in Production Photo: Kornit / ZwissTex
06.09.2023

ZwissTex integrates Kornit Technology in Production

Germany-based ZwissTex is a leading manufacturer of textiles with over 150 years of experience, creating innovative and sustainable textile solutions for the automotive and apparel industries. The company also operates in Mexico, to specifically serve the automotive sector across North American Free Trade Agreement (NAFTA) markets. Via OEMs, ZwissTex supplies German automakers including Volkswagen Auto Group, BMW, and Mercedes, as well as American manufacturers in select cases.

Unlike other Kornit customers, ZwissTex had no previous experience printing their own materials, and saw Kornit’s sustainable, single-step, Presto MAX S production system as an effective means of increasing their product capabilities.

Germany-based ZwissTex is a leading manufacturer of textiles with over 150 years of experience, creating innovative and sustainable textile solutions for the automotive and apparel industries. The company also operates in Mexico, to specifically serve the automotive sector across North American Free Trade Agreement (NAFTA) markets. Via OEMs, ZwissTex supplies German automakers including Volkswagen Auto Group, BMW, and Mercedes, as well as American manufacturers in select cases.

Unlike other Kornit customers, ZwissTex had no previous experience printing their own materials, and saw Kornit’s sustainable, single-step, Presto MAX S production system as an effective means of increasing their product capabilities.

“Our textiles were not classically printed in the past, and we did not produce any classical textiles in fashion, which is why we didn’t have any printing experience internally,” said Ralph Moldan, Technical Specialist at ZwissTex, as the system was being installed in their facility. “The only option was to find a system that would enable us to implement the areas in which we are active on the market easily and quickly, without requiring a lot of printing experience.”

One benefit of integrating Kornit technology into the ZwissTex production ecosystem: applying ink only where it is needed and seen, rather than to the full surface of each material. This translates to both reducing the company’s carbon footprint, and minimizing materials waste for a more cost-effective operation.

Prior to making the decision to invest in Kornit, ZwissTex conducted a series of tests and consultations, evaluating possible applications for different materials and engaging with their own key clients to ensure these finished products would meet their rigorous quality and durability standards. This included presenting Kornit-decorated samples at the Techtextil 2022 exhibition in Frankfurt.

Moldan found Kornit’s production capabilities opened new doors to customization of interior areas, a market that continues to grow. He anticipates this technology will create new opportunities with customers they could not reach previously, including new opportunities in sectors such as motor homes, airlines, and aircraft outfitters.

Source:

Kornit Digital

(c) AkzoNobel
12.07.2022

AkzoNobel announces €20 million investment and creates new jobs in France

A €20 million investment has been announced by AkzoNobel to increase and improve production at two of its sites in France. Around 30 new jobs will be created.

A total of €15 million will be spent on the company’s aerospace coatings facility in Pamiers, which was taken over following the Mapaero acquisition in 2019. Production capacity is being boosted by 50%, while the funds will also be used to reduce environmental impact and improve safety processes and working conditions.

The other €5 million will be spent on improving production flexibility at the decorative paints site in Montataire, which is one of the company’s most important manufacturing locations for wall paints in Europe.

The plans for Pamiers include the construction of two extensions, one for storage and one for cleaning and waste treatment. The project will also enable the company to relocate the production of exterior polyurethane paints for aircraft widely used in Europe from its Waukegan plant in the US.

Building work is expected to start by the end of 2023, with the new installations at both locations due to be operational in early 2025.

A €20 million investment has been announced by AkzoNobel to increase and improve production at two of its sites in France. Around 30 new jobs will be created.

A total of €15 million will be spent on the company’s aerospace coatings facility in Pamiers, which was taken over following the Mapaero acquisition in 2019. Production capacity is being boosted by 50%, while the funds will also be used to reduce environmental impact and improve safety processes and working conditions.

The other €5 million will be spent on improving production flexibility at the decorative paints site in Montataire, which is one of the company’s most important manufacturing locations for wall paints in Europe.

The plans for Pamiers include the construction of two extensions, one for storage and one for cleaning and waste treatment. The project will also enable the company to relocate the production of exterior polyurethane paints for aircraft widely used in Europe from its Waukegan plant in the US.

Building work is expected to start by the end of 2023, with the new installations at both locations due to be operational in early 2025.

AkzoNobel employs nearly 1,500 people in France and operates four production facilities, in Montataire (decorative paints), Dourdan (powder coatings), Limoges (adhesive markings) and Pamiers (aerospace coatings).

More information:
AkzoNobel Coatings aerospace
Source:

AkzoNobel

Expansion begins at Hexcel Engineered Core Operations Plant in Morocco (c) Hexcel Corporation
15.03.2022

Expansion begins at Hexcel Engineered Core Operations Plant in Morocco

Hexcel Corporation hosted customers and public officials at its manufacturing site in the Midparc Free Trade Zone in Casablanca as the company broke ground on an expansion that will double the size of its existing engineered core manufacturing operation in Morocco to meet increased demand from aerospace customers for lightweight advanced composites.

The expansion, announced in September 2021, is expected to be completed in early 2023. The plant size will double to 24,000 square meters and employment is expected to increase from 120 to 400 people when the expansion is completed.

The Casablanca facility was built as part of Hexcel’s ongoing worldwide investment to create a diversified and robust global supply chain to support aerospace customers’ growing demand for engineered core. At the plant, Hexcel transforms lightweight honeycomb materials into engineered core parts to reinforce structures in the aerospace industry, particularly for aircraft, engine nacelles, and helicopter blades.

Hexcel Corporation hosted customers and public officials at its manufacturing site in the Midparc Free Trade Zone in Casablanca as the company broke ground on an expansion that will double the size of its existing engineered core manufacturing operation in Morocco to meet increased demand from aerospace customers for lightweight advanced composites.

The expansion, announced in September 2021, is expected to be completed in early 2023. The plant size will double to 24,000 square meters and employment is expected to increase from 120 to 400 people when the expansion is completed.

The Casablanca facility was built as part of Hexcel’s ongoing worldwide investment to create a diversified and robust global supply chain to support aerospace customers’ growing demand for engineered core. At the plant, Hexcel transforms lightweight honeycomb materials into engineered core parts to reinforce structures in the aerospace industry, particularly for aircraft, engine nacelles, and helicopter blades.

At the event, Thierry Merlot, Hexcel President – Aerospace for Europe, MEA/AP & Industrial, said, “We are pleased to celebrate this milestone with our customers and with the local community. The increased demand for lightweight, aerodynamic, advanced composites is growing, and our customers including Safran, Airbus, Airbus Atlantic, Boeing and Spirit AeroSystems have shown confidence in our ability to meet that demand. We appreciate the support from them as well as from the Ministry and everyone in the local community who continue providing us with the opportunity to further our investment in Morocco. The very successful establishment of Hexcel, the qualification of the workforce, the support of the state and the proximity of our customers have been real assets to launch this extension of our site in Casablanca.”

Source:

Hexcel Corporation

(c) ITA
16.12.2021

International Sustainable Aviation and Energy Society Award for Professor Thomas Gries

On 27 November 2021, the Scientific Award for International Sustainable Aviation and Energy Society (SARES Award) was awarded to Professor Dr Thomas Gries from the Institut für Textiltechnik of RWTH Aachen University. The award ceremony took place during the closing ceremony of the International Symposium on Sustainable Aviation (ISSA) in a hybrid format online and simultaneously at Kasetsart University, Bangkok, Thailand.
 
With the award, the committee recognised the ongoing contribution of Pro-fessor Gries and the Institut für Textiltechnik to the digitisation and bio-transformation of the textile sector, as well as the Institute as a place of innovation for sustainable aviation.

On 27 November 2021, the Scientific Award for International Sustainable Aviation and Energy Society (SARES Award) was awarded to Professor Dr Thomas Gries from the Institut für Textiltechnik of RWTH Aachen University. The award ceremony took place during the closing ceremony of the International Symposium on Sustainable Aviation (ISSA) in a hybrid format online and simultaneously at Kasetsart University, Bangkok, Thailand.
 
With the award, the committee recognised the ongoing contribution of Pro-fessor Gries and the Institut für Textiltechnik to the digitisation and bio-transformation of the textile sector, as well as the Institute as a place of innovation for sustainable aviation.

Examples of this include the development of 3D braided ceramic matrix composite components for aircraft engines, which were researched together with partners in a Horizon 2020 project (EU project AllOxITD). The ongoing Chrysomallos research project as another example, funded under the national aeronautics research programme in Germany, aims to develop a completely new and sustainable high-performance insulator for aircraft cabins based on aerogels. These have a significantly lower weight than the glass fibre mats used up to now, while providing the same insulation performance, and solve the problem of the previously high manufacturing costs of aerogels. The aim of the project is to develop an insulation material with reduced density (reduction of more than 20 percent). To this end, a new type of insulation material based on aerogel is to be developed. The basis is an aerogel fleece (0.06 W/mK at 28 kg/m³), which has already been developed as part of a dissertation at the Institut für Textiltechnik of RWTH Aachen University (Mroszczok, J.: 2019).

The aviation industry is one of the fastest growing industries in the world. Due to this fact and its importance for society and the global economy, it needs to make special efforts towards sustainability. The ISSA, an international multi-disciplinary symposium, aims to address current issues in aviation such as improving aircraft fuel efficiency, promoting the use of biofuels, minimising environmental impact, mitigating greenhouse gas emissions and reducing engine and aircraft noise. ^

Through the award, SARES honours scientists and researchers whose work on sustainable aviation issues has made an important contribution at the international level. The selection is based on the scientific publications of the applicant or nominee, the h-index, i.e. the key figure for the worldwide perception of a scientist in professional circles, the project topics and the project results.

VDMA: Top young talent with cutting-edge topics  (c) VDMA
The 2021 winners (from top left to right): Dr Martin Hengstermann, Irina Kuznik, Kai-Chieh Kuo.
10.11.2021

VDMA: Top young talent with cutting-edge topics

The Chairman of the Walter Reiners-Stiftung foundation of the VDMA Textile Machinery Association, Peter D. Dornier has awarded prizes to three successful young engineers. The award-winning works provide practical solutions on the topic of circular economy. For example, the recycling of carbon fibres, which are used to produce lightweight components for the automotive industry. Or the environmentally friendly production of yarns from crab shells. Another topic was medical applications: The processing of ultra-fine yarns into stents for aortic repair. The award ceremony took place online on 9 November as part of the Aachen-Dresden-Denkendorf International Textile Conference.  

With a creativity prize, endowed with 3,000 euros, the foundation honoured the diploma thesis of Irina Kuznik, TU Dresden. She used a creative approach to realise solutions for processing chitosan into fibre yarn.

The Chairman of the Walter Reiners-Stiftung foundation of the VDMA Textile Machinery Association, Peter D. Dornier has awarded prizes to three successful young engineers. The award-winning works provide practical solutions on the topic of circular economy. For example, the recycling of carbon fibres, which are used to produce lightweight components for the automotive industry. Or the environmentally friendly production of yarns from crab shells. Another topic was medical applications: The processing of ultra-fine yarns into stents for aortic repair. The award ceremony took place online on 9 November as part of the Aachen-Dresden-Denkendorf International Textile Conference.  

With a creativity prize, endowed with 3,000 euros, the foundation honoured the diploma thesis of Irina Kuznik, TU Dresden. She used a creative approach to realise solutions for processing chitosan into fibre yarn.

Mr Kai-Chieh Kuo was awarded the diploma/master's thesis promotion prize of 3,500 euros. With his master's thesis, which was written at RWTH Aachen University, Mr Kuo contributes to the production of vital components used in medicine. The stents made of ultra-fine yarns are made possible by an innovative modification of the classic tube weaving process.

The Walter Reiners Foundation rewarded the doctoral thesis of Dr. Martin Hengstermann with the promotional prize in the dissertation category, endowed with 5,000 euros. The thesis deals with the production of recycled carbon fibres. These can be used to produce lightweight components for motor vehicle and aircraft construction or the wind energy sector.

New Prize Sustainability / Circular Economy
The environmental conditions of the textile industry and machine construction are changing. Topics such as climate protection and the circular economy are becoming central. From this perspective, the board of the Walter Reiners Foundation has decided to further develop the foundation's prize system.

In 2022, the foundation will for the first time offer a prize with a focus on design / sustainability. Peter D. Dornier, Chairman of the Foundation, explained: "Already in the design phase, one can set the parameters so that a textile product can be reintroduced after use into the economic cycle for a high-quality application. For example, through the appropriate use of materials and finishing. We are looking for solutions for resource-saving design, technology and manufacturing processes."   

19.10.2021

Teijin to boost Heat-Resistant Carbon Fiber Prepreg Production

Teijin Limited announced today that its carbon fiber subsidiary Renegade Materials Corporation, a leading U.S.-based supplier of highly heat-resistant thermoset prepregs, resins and adhesives for the aerospace industry, will expand its prepreg production by 2.5 times approximately. The increased capacity, which aligns with Renegade’s capacity expansion strategy at the Miamisburg, Ohio location, is the result of a USD 4 million investment made in December 2019 and the construction was started in March 2020. Operation of the new production lines will commence January 2022.

Renegade Materials' heat-resistant thermoset prepregs, resins and adhesives are well trusted by U.S. and European aircraft manufacturers and aircraft engine suppliers.

Renegade Materials will showcase its high heat-resistant thermoset prepreg at the Composites and Advanced Materials Expo (CAMX), one of the largest, most comprehensive composites and advanced materials event in North America, at the Dallas Convention Center in Dallas, Texas, from October 19 to 21.

Teijin Limited announced today that its carbon fiber subsidiary Renegade Materials Corporation, a leading U.S.-based supplier of highly heat-resistant thermoset prepregs, resins and adhesives for the aerospace industry, will expand its prepreg production by 2.5 times approximately. The increased capacity, which aligns with Renegade’s capacity expansion strategy at the Miamisburg, Ohio location, is the result of a USD 4 million investment made in December 2019 and the construction was started in March 2020. Operation of the new production lines will commence January 2022.

Renegade Materials' heat-resistant thermoset prepregs, resins and adhesives are well trusted by U.S. and European aircraft manufacturers and aircraft engine suppliers.

Renegade Materials will showcase its high heat-resistant thermoset prepreg at the Composites and Advanced Materials Expo (CAMX), one of the largest, most comprehensive composites and advanced materials event in North America, at the Dallas Convention Center in Dallas, Texas, from October 19 to 21.

Source:

Teijin Carbon Europe GmbH

02.06.2021

Teijin: Tenax™ Carbon Fiber Prepreg Adopted for Next-Generation Aircraft Engine Nacelle

Teijin Limited announced today that its Tenax™ carbon fiber prepreg has been adopted for a part of nacelle, or streamlined housing, for next-generation aircraft engine to be used by Airbus. A prototype of the nacelle part, which Nikkiso Co., Ltd. is developing for Airbus’s Propulsion of Tomorrow project, will be delivered to Airbus by the end of 2021.

The Tenax™ prepreg used for the nacelle part was developed especially for aircraft applications using high-performance and rapid-curing epoxy resin. Notably, the Tenax™ prepreg can be molded at a lower temperature and in a shorter time than conventional prepregs for aircraft applications. In addition to general autoclave molding, the Tenax™ prepreg also is suited to press molding for mass production, achieving excellent quality required for aircraft applications. Furthermore, it is compatible with automated fiber placement (AFP) therefore can be combined with automatic laminating technology and short-time molding to maximize production efficiency. The excellent productivity and cost efficiency of the Tenax™ prepreg were key reasons why it was adopted for Nikkiso’s nacelle.

Teijin Limited announced today that its Tenax™ carbon fiber prepreg has been adopted for a part of nacelle, or streamlined housing, for next-generation aircraft engine to be used by Airbus. A prototype of the nacelle part, which Nikkiso Co., Ltd. is developing for Airbus’s Propulsion of Tomorrow project, will be delivered to Airbus by the end of 2021.

The Tenax™ prepreg used for the nacelle part was developed especially for aircraft applications using high-performance and rapid-curing epoxy resin. Notably, the Tenax™ prepreg can be molded at a lower temperature and in a shorter time than conventional prepregs for aircraft applications. In addition to general autoclave molding, the Tenax™ prepreg also is suited to press molding for mass production, achieving excellent quality required for aircraft applications. Furthermore, it is compatible with automated fiber placement (AFP) therefore can be combined with automatic laminating technology and short-time molding to maximize production efficiency. The excellent productivity and cost efficiency of the Tenax™ prepreg were key reasons why it was adopted for Nikkiso’s nacelle.

Teijin is intensively accelerating its development of mid- to downstream applications for aircraft, one of the strategic focuses of its medium-term management plan for 2020-2022. Going forward, Teijin intends to further strengthen its carbon fiber and intermediate material businesses to contribute to increasing global sustainability, aiming to become a company that supports the society of the future.

Source:

Teijin

(c) Teijin Carbon Europe GmbH
19.05.2021

Teijin Carbon produces new thermoplastic PPS-Tape

Teijin Carbon Europe introduces a new thermoplastic carbon fiber tape (TPUD) based on PPS. The new Tenax™ TPUD with PPS matrix allows entry in new cost-sensitive markets while offering the typical TPUD advantages like high resistance to chemicals and solvents, low flammability, storage or shipping at room temperature and recyclability.  

Due to its flame retardant properties and low smoke emission, it can be used in interior applications of aircraft or rail vehicles, among others. The maximum continuous operating temperature is up to 220 °C. Very low water absorption, excellent creep resistance even at elevated temperatures and high dimensional stability round off the property portfolio of this new TPUD. It is therefore also suitable for demanding applications in the aerospace, oil & gas, sporting goods or industrial sectors, while remaining cost-effective. These properties make the product perfect for highly automated processing routes such as ATL or AFP in combination with overmolding for complex geometries. Production start for the Tenax™ TPUD with PPS matrix is the first quarter in 2021.

Teijin Carbon Europe introduces a new thermoplastic carbon fiber tape (TPUD) based on PPS. The new Tenax™ TPUD with PPS matrix allows entry in new cost-sensitive markets while offering the typical TPUD advantages like high resistance to chemicals and solvents, low flammability, storage or shipping at room temperature and recyclability.  

Due to its flame retardant properties and low smoke emission, it can be used in interior applications of aircraft or rail vehicles, among others. The maximum continuous operating temperature is up to 220 °C. Very low water absorption, excellent creep resistance even at elevated temperatures and high dimensional stability round off the property portfolio of this new TPUD. It is therefore also suitable for demanding applications in the aerospace, oil & gas, sporting goods or industrial sectors, while remaining cost-effective. These properties make the product perfect for highly automated processing routes such as ATL or AFP in combination with overmolding for complex geometries. Production start for the Tenax™ TPUD with PPS matrix is the first quarter in 2021.

For almost 10 years, unidirectional tapes (TPUD) have been manufactured from carbon fibers and thermoplastics in Heinsberg, Germany. The semi-finished products have so far been offered with PEEK or PAEK – and PPS is now added to the list of available matrixes. PPS allows a lower process temperature compared to PEEK or PAEK. For the industrial market in particular, increasing the production rate to make processes more cost-efficient is an opportunity.

Source:

Teijin Carbon Europe GmbH

MaruHachi/AMAC: High-temperature thermoplastic tapes and laminates (c) MaruHachi
16.02.2021

MaruHachi/AMAC: High-temperature thermoplastic tapes and laminates

With their recently installed high-temperature unidirectional tape line, Japan-based composites manufacturer MaruHachi enables new opportunities for high-end applications in demanding market segments like aerospace, automotive or others outperforming traditional materials based on PP and PA which are already widely available.

In the first phase, MaruHachi will produce up to 40 tons/year and focuses now specifically on high-temperature thermoplastic uni-directional (UD) tapes and multi-layer sheet laminates. The material is based on high-performance fibers like carbon, aramid, glass or natural fibers and the matrix can be high-performance polymers like PPS, PEEK or other higher temperature polymers, which are much tougher than epoxies and easy to recycle. With a width of 500 mm, a specific weight from 60 to 350 g/m2, depending on the chosen material, the lines can operate under temperatures up to 420 degrees Celsius. Working under these extremely high temperatures allows for better material properties of the final application, higher performance, increased resistance and integrated high-performance functionalities e.g. by overmoulding.

With their recently installed high-temperature unidirectional tape line, Japan-based composites manufacturer MaruHachi enables new opportunities for high-end applications in demanding market segments like aerospace, automotive or others outperforming traditional materials based on PP and PA which are already widely available.

In the first phase, MaruHachi will produce up to 40 tons/year and focuses now specifically on high-temperature thermoplastic uni-directional (UD) tapes and multi-layer sheet laminates. The material is based on high-performance fibers like carbon, aramid, glass or natural fibers and the matrix can be high-performance polymers like PPS, PEEK or other higher temperature polymers, which are much tougher than epoxies and easy to recycle. With a width of 500 mm, a specific weight from 60 to 350 g/m2, depending on the chosen material, the lines can operate under temperatures up to 420 degrees Celsius. Working under these extremely high temperatures allows for better material properties of the final application, higher performance, increased resistance and integrated high-performance functionalities e.g. by overmoulding.

Since 2017, MaruHachi Group is active in the European market in cooperation with Dr. Michael Effing,the CEO of AMAC GmbH, who advises and supports the company strategically. The established, family-owned MaruHachi Group has a strong history in automotive and medical textiles and has been active in the innovative composites market for more than 15 years.

Toshi Sugahara, CEO of MaruHachi: “For many years, we have already been cooperating with domestic and international partners on high-demand applications and therefore, MaruHachi decided now to invest over 1 million EUR in this new line in phase 1, including a funding participation from the Japanese government NEDO. New developments in phase 2 will be be undertaken by end of 2021 on the downstream technologies like the automated preforming and consolidation. With our new products, we want to contribute to significant weight reductions of the final products, thus improve energy efficiency while offering a cost-efficient and high-quality solution.”

Dr. Effing, CEO of AMAC GmbH confirms: „The focus on the niche of high-temperature products based on PPS and PEEK allows MaruHachi on very demanding high-end applications such as structural frames on space and aircrafts, aircraft seats or engine components etc. The tapes are fully recyclable and can be processed e.g. with high-speed with laser-based tape placement machines and robots.”

Source:

AMAC GmbH

14.12.2020

Hexcel and Safran Expand Scope of Existing Contract

Hexcel and Safran Expand Scope of Existing Contract for Advanced Composite Materials on Commercial Aerospace Programs

Hexcel Corporation (NYSE: HXL) announced today that the scope of its long-term supplier contract with Safran S.A. has been expanded to include advanced composite materials for a broader range of commercial aerospace applications.

For more than three decades, Hexcel has been a trusted, leading supplier of high-performance, advanced composites such as carbon fiber, adhesives, prepregs, dry fabrics, and honeycomb core to Safran programs. Since 2013, Hexcel HexTow® IM7 carbon fiber has been supplied for the LEAP*-1A, -1B and -1C engine programs. That contract now has been amended to include HexTow IM7 for the GE9X engine that powers the Boeing 777X.The contract also includes Hexcel core, adhesives, prepregs, and fabrics for additional applications on engine nacelles and aircraft interiors.

Hexcel and Safran Expand Scope of Existing Contract for Advanced Composite Materials on Commercial Aerospace Programs

Hexcel Corporation (NYSE: HXL) announced today that the scope of its long-term supplier contract with Safran S.A. has been expanded to include advanced composite materials for a broader range of commercial aerospace applications.

For more than three decades, Hexcel has been a trusted, leading supplier of high-performance, advanced composites such as carbon fiber, adhesives, prepregs, dry fabrics, and honeycomb core to Safran programs. Since 2013, Hexcel HexTow® IM7 carbon fiber has been supplied for the LEAP*-1A, -1B and -1C engine programs. That contract now has been amended to include HexTow IM7 for the GE9X engine that powers the Boeing 777X.The contract also includes Hexcel core, adhesives, prepregs, and fabrics for additional applications on engine nacelles and aircraft interiors.

“It was time to include Safran Cabin, Safran Seats and Safran Aerosystems within our global long-term agreement,” said Thierry Viguier, Vice President, Safran Materials Purchasing. “Hexcel has shown again, during this difficult period of time, that they are a strong and reliable long-term partner.”

“This contract expansion is the result of a successful, collaborative relationship between Safran and Hexcel that started more than 35 years ago to serve the aerospace industry,” said Thierry Merlot, President Aerospace Europe, Asia Pacific, Middle East, Africa & Industrial. “This agreement will further strengthen the long-term partnership between our companies and reinforces our strategic position within Safran’s First Circle suppliers.”

Reach Group: Composites China Trade Show (c) REACH Group
10.09.2020

AMAC/Germany and REACH Group/China: first life business activity since Covid-19 at the Composites China Trade Show in Shanghai

As the first composites trade show worldwide since the Covid-19-crisis, the China Composites in Shanghai (September 2 to 4, 2020) took up its activity. The show counted about 600 exhibitors and over 20 000 visitors, mostly Chinese locals, attended the exhibition.

Chinese Reach Group under the lead of its president Daniel He represented a large portfolio of European companies and their recent developments through their cooperation with Dr. Michael Effing´s AMAC/Germany, among them Airborne (NL), Textechno (D) and Conbility (D).

As the first composites trade show worldwide since the Covid-19-crisis, the China Composites in Shanghai (September 2 to 4, 2020) took up its activity. The show counted about 600 exhibitors and over 20 000 visitors, mostly Chinese locals, attended the exhibition.

Chinese Reach Group under the lead of its president Daniel He represented a large portfolio of European companies and their recent developments through their cooperation with Dr. Michael Effing´s AMAC/Germany, among them Airborne (NL), Textechno (D) and Conbility (D).

Daniel He describes the situation: „The Chinese market is picking up again; a price increase of 7% for glass fibers was announced right before the China Composites Show, on August 25th 2020, which was even leading to a temporary material shortage. Today, the most booming industries in China are wind energy, building and infrastructure and innovation for electric cars. Unlike the rest of the world, where the aircraft industry undergoes a deep decline, in China it takes up by 50 %, which is very promising. Furthermore, we expect half a year for a full recovery of the industry, while the China growth of 2020 is still expected to be between 2 and 4 %.“

Michael Effing replied: “Enabling the composites business between China and Europe is the aim of our cooperation with Reach and with our customers, which are active in digital automatization, testing equipment or cost optimization software. We are very happy to have been present in China through our representant Reach and are looking forward to bridge and overcome the Covid-19-crisis with our upcoming event in Germany, the Composites for Europe in Stuttgart in November and hope to be back to full global business speed at the JEC in Paris in 2021.“

Source:

AMAC GmbH

Flight Design selects Hexcel’s HexPly® M79 Carbon Fiber Prepregs for Ultralight Aircraft (c) Hexcel Corporation
30.04.2020

Flight Design selects Hexcel’s HexPly® M79 Carbon Fiber Prepregs for Ultralight Aircraft

STAMFORD – German ultralight aircraft specialist Flight Design has chosen Hexcel as its key supplier adopting low-temperature curing prepreg into its aircraft production. Hexcel’s HexPly® M79 Carbon Fiber prepregs deliver a more consistent final product by ensuring constant material quality and processing parameters and produce a lighter and stronger aircraft at a more competitive overall cost.

Flight Design has always relied heavily on composites for its aircrafts’ ultralight construction and turned to long-term composite materials partner Lange + Ritter, part of Hexcel’s European distribution network, when they began searching for a prepreg material solution. Hexcel and Lange + Ritter created several new product codes specifically for Flight Design and then supplied materials for initial handling trials and prototyping. Hexcel’s HexPly M79 low temperature curing out of autoclave solution was first used in the new F2 prototype. As part of its material supply package, Lange + Ritter also sent a team for on-site training and technical support, allowing the Flight Design production team to get up to speed with prepreg as quickly as possible.

STAMFORD – German ultralight aircraft specialist Flight Design has chosen Hexcel as its key supplier adopting low-temperature curing prepreg into its aircraft production. Hexcel’s HexPly® M79 Carbon Fiber prepregs deliver a more consistent final product by ensuring constant material quality and processing parameters and produce a lighter and stronger aircraft at a more competitive overall cost.

Flight Design has always relied heavily on composites for its aircrafts’ ultralight construction and turned to long-term composite materials partner Lange + Ritter, part of Hexcel’s European distribution network, when they began searching for a prepreg material solution. Hexcel and Lange + Ritter created several new product codes specifically for Flight Design and then supplied materials for initial handling trials and prototyping. Hexcel’s HexPly M79 low temperature curing out of autoclave solution was first used in the new F2 prototype. As part of its material supply package, Lange + Ritter also sent a team for on-site training and technical support, allowing the Flight Design production team to get up to speed with prepreg as quickly as possible.

HexPly M79 prepregs can be cured at temperatures as low as 70˚C for eight hours or 80˚C for four hours, reducing tooling costs and increasing build rates. When combined with Hexcel’s innovative air venting Grid Technology, HexPly M79 UD carbon tapes can also be laminated with reduced debulking steps to produce void contents <1% irrespective of laminate thickness. With consistently low void contents and improved mechanical properties, designers and engineers are able to further optimize highly loaded composite aerostructures.

As more and more of its composite aircraft parts are transferred to prepreg technology, Flight Design is seeing the benefits of its switch to HexPly M79. Lay-up is cleaner and more precise, low temperature oven curing is quick and energy efficient, and the manufacturing process consistently outputs exceptionally high-quality laminates and components. The long-term strategy is to integrate HexPly M79 across the range, with Hexcel materials lightening the ultralight aircraft at Flight Design even further.

“The materials and technology package from Hexcel and Lange + Ritter has been a big success for us at Flight Design,” comments Daniel Gunther, Managing Director at Flight Design. “When we took the decision to switch to prepreg, we looked at many options but only Hexcel and Lange + Ritter could offer us low temperature out-of-autoclave (OOA) curing, globally respected material quality and the customer service levels we were searching for.”

Hexcel at JEC World 2020
Hexcel at JEC World 2020
25.02.2020

Hexcel at JEC World 2020

Hexcel’s Leading Position in Aerospace and Automotive Makes Hexcel a Trusted Partner for Urban Air Mobility

At this year’s JEC World in Paris on March 3-5, Hexcel will highlight the growing need for innovations in composite materials to support the emerging Urban Air Mobility (UAM) market.

Urban air mobility – urban transportation systems that move people by air or enable cargo deliveries – is the next big transportation innovation. Similar to taxis or ride sharing today, UAM will help remove congestion from our streets and provide a convenient, rapid method for travel in urban centers as well as in remote areas.

Advanced composite materials will be at the heart of UAM vehicles by providing lightweight, efficient, reliable, and cost-competitive options for manufacturing. “Materials have been a key driver of efficiency for aircraft today, and they will be even more important for the emerging UAM marketplace,” said Imad Atallah, Director of Strategic Marketing for Aerospace and Urban Air Mobility at Hexcel.

Hexcel’s Leading Position in Aerospace and Automotive Makes Hexcel a Trusted Partner for Urban Air Mobility

At this year’s JEC World in Paris on March 3-5, Hexcel will highlight the growing need for innovations in composite materials to support the emerging Urban Air Mobility (UAM) market.

Urban air mobility – urban transportation systems that move people by air or enable cargo deliveries – is the next big transportation innovation. Similar to taxis or ride sharing today, UAM will help remove congestion from our streets and provide a convenient, rapid method for travel in urban centers as well as in remote areas.

Advanced composite materials will be at the heart of UAM vehicles by providing lightweight, efficient, reliable, and cost-competitive options for manufacturing. “Materials have been a key driver of efficiency for aircraft today, and they will be even more important for the emerging UAM marketplace,” said Imad Atallah, Director of Strategic Marketing for Aerospace and Urban Air Mobility at Hexcel.

Already, Hexcel is a leader in advanced composite materials for the aerospace market and is a key supplier of composite materials to the automotive industry. So, the company is well positioned to offer solutions to meet the critical needs of high-rate and quick-part manufacturing cycles, in addition to low-cost needs for this space. Hexcel’s materials solutions approach for UAM is to make it greener and more sustainable, safer, more comfortable, and more affordable.

Hexcel’s broad range of carbon fiber and HexPly® prepreg solutions, including snap cure thermosets and thermoplastics, coupled with the most qualified positions on aerospace programs in the industry make the company a trusted partner for UAM. In addition to offering composite materials from carbon fibers, prepregs, honeycomb and reinforcements, Hexcel’s best-performing market solution in noise absorption on aircraft jet engines, Acousti-Cap®, provides a strong position of innovation to solve one of the most critical problems in the UAM space – community noise. “We are applying our technologies to the unique needs of urban air mobility vehicles,” Atallah said.

Hexcel’s ability to bring materials technology from the aerospace and automotive industries represents a unique strength in solving the critical challenges of UAM, especially around high-rate manufacturing, low-cost materials, light weighting, and noise. “Both thermoplastics and quick-cure thermoset materials are expected to have applications on UAM vehicles,” Atallah said. Furthermore, Hexcel’s broad product portfolio including unsized carbon fiber has proven to be the most compatible with thermoplastic resins from a consolidation perspective.

More information:
Hexcel JEC World
Source:

AGENCE APOCOPE

SGL Carbon und Solvay schließen Kooperation zur Entwicklung von im hohen Maße konkurrenzfähigen und fortschrittlichen Carbonfaser-Verbundwerkstoffen für Primärstrukturen in der Luftfahrt (c) SGL CARBON SE
SGL Carbon Large-Tow-IM-Carbonfaser Produktion am US-Standort Moses Lake
03.12.2019

Collaboration between SGL Carbon and Solvay

SGL Carbon and Solvay collaborate to develop highly-competitive advanced carbon fiber composites for aerospace primary structures

SGL Carbon and Solvay have entered into a joint development agreement (JDA) to bring to market the first composite materials based on large-tow intermediate modulus (IM) carbon fiber. These materials, which address the need to reduce costs and CO2 emissions, and improve the production process and fuel efficiency of next-generation commercial aircraft, will be based on SGL Carbon’s large-tow IM carbon fiber and Solvay’s primary structure resin systems.

The agreement encompasses both thermoset and thermoplastic composite technologies. It builds on Solvay’s leadership in supplying advanced materials to the aerospace industry and SGL Carbon’s expertise in high-volume carbon fiber manufacturing.

SGL Carbon and Solvay collaborate to develop highly-competitive advanced carbon fiber composites for aerospace primary structures

SGL Carbon and Solvay have entered into a joint development agreement (JDA) to bring to market the first composite materials based on large-tow intermediate modulus (IM) carbon fiber. These materials, which address the need to reduce costs and CO2 emissions, and improve the production process and fuel efficiency of next-generation commercial aircraft, will be based on SGL Carbon’s large-tow IM carbon fiber and Solvay’s primary structure resin systems.

The agreement encompasses both thermoset and thermoplastic composite technologies. It builds on Solvay’s leadership in supplying advanced materials to the aerospace industry and SGL Carbon’s expertise in high-volume carbon fiber manufacturing.

“For Solvay, this is an opportunity to lead the aerospace adoption of a composite material based on 50K IM carbon fiber. This is a highly competitive value proposition that brings more affordable high-performance solutions to our customers. We see this as the first step in a long-term partnership,” said Augusto Di Donfrancesco, member of Solvay’s executive committee.

“By combining SGL’s carbon fiber expertise in our newly developed, unique 50K IM fiber with Solvay’s resin formulation and aerospace market expertise, both partners are aiming to develop an advanced aerospace material system. This alliance supports our strategic direction and accelerates our growth in the attractive aerospace market,” said Dr. Michael Majerus, spokesman of the management board of SGL Carbon.

Composite materials for aerospace applications represent a multi-billion-dollar market that is expected to grow strongly in the coming decade. Solvay and SGL Carbon are uniquely positioned to develop solutions to address the needs of this market.

More information:
Solvay SGL Carbon Carbonfaser
Source:

SGL CARBON SE

(c) Eric RAZ, Airbus Helicopters
25.11.2019

SGL Carbon serially delivers composite materials for rotor blades to Airbus Helicopters

  • Glass fiber textiles for helicopter type H145
  • First ever material supply for primary structural components in the aerospace segment

Since August of this year, SGL Carbon delivers two special glass fiber textiles, so-called non-crimped fabrics, for the new version of helicopter model H145 from Airbus Helicopters. These materials are used in the new, especially efficient five-blade rotor. Developed in close collaboration with Airbus Helicopters, the material has been qualified for the application for the next years to come.  

Thanks to their unidirectional fiber orientation, the fabrics are extremely resistant, providing optimal support for the new geometry of the especially long H145 rotor blades. The fabrics are manufactured at the SGL Carbon site in Willich near Düsseldorf in a multi-stage process and delivered to Airbus Helicopters in Paris.  

  • Glass fiber textiles for helicopter type H145
  • First ever material supply for primary structural components in the aerospace segment

Since August of this year, SGL Carbon delivers two special glass fiber textiles, so-called non-crimped fabrics, for the new version of helicopter model H145 from Airbus Helicopters. These materials are used in the new, especially efficient five-blade rotor. Developed in close collaboration with Airbus Helicopters, the material has been qualified for the application for the next years to come.  

Thanks to their unidirectional fiber orientation, the fabrics are extremely resistant, providing optimal support for the new geometry of the especially long H145 rotor blades. The fabrics are manufactured at the SGL Carbon site in Willich near Düsseldorf in a multi-stage process and delivered to Airbus Helicopters in Paris.  

“The order emphasizes our growing presence in the aerospace business. With the fabrics for Airbus Helicopters, we have realized, qualified, and started serial production for a material concept for primary structural components for the first time,” underscores Dr. Andreas Erber, Head of the Aerospace segment in the business unit Composites – Fibers & Materials at SGL Carbon.

The current deliveries are part of a framework contract with Airbus Helicopters, intended to gradually intensify collaboration. Besides the current development of materials for helicopter components, Airbus Helicopters and SGL Carbon have worked together in the area of component material processing for Airbus group aircraft doors for years. In addition, Airbus and SGL Carbon are jointly involved in various associations and research projects in the area of components, such as Carbon Composites e.V.

 

More information:
SGL Carbon
Source:

SGL CARBON SE

Airborne / AMAC GmbH (c) AMAC GmbH
28.10.2019

Airborne strengthens its activities in the D-A-CH region with AMAC

As of October 1st, 2019, the Netherlands-based global market leading manufacturer of advanced automation equipment and solutions for composites, Airborne, strengthens its activities particularly in German speaking countries, the so-called D-A-CH region, comprising Germany, Austria and Switzerland with Dr. Michael Effing from AMAC. The Dutch company is looking for specialised partnerships to develop and deepen its international business opportunities in the aerospace and automotive markets.

As of October 1st, 2019, the Netherlands-based global market leading manufacturer of advanced automation equipment and solutions for composites, Airborne, strengthens its activities particularly in German speaking countries, the so-called D-A-CH region, comprising Germany, Austria and Switzerland with Dr. Michael Effing from AMAC. The Dutch company is looking for specialised partnerships to develop and deepen its international business opportunities in the aerospace and automotive markets.

Airborne’s focus is on high-end composite components, at high production rates at radically low conversion costs. Airborne is building up a suite of automated solutions for the manufacturing of composites with the aim to radically reduce costs and touch labour, minimize the footprint and use of material, and improve the time to market for their clients. The company offers i.a. solutions in automated honeycomb potting, automated kitting and automated lamination of thermosets and thermoplastics. In order to develop new business opportunities in the D-A-CH region for the end-markets aerospace and automotive, Airborne is cooperating with AMAC to accelerate the process of locating suitable partnerships.

Dr. Effing, CEO of AMAC GmbH confirms: "As a first step for the establishment of Airborne on the German market, we just signed their membership at AZL in Aachen which will help to connect with over 80 companies and latest research developments. In the framework of theirstrategy to strengthen the supply to the aircraft sector, Airborne will also exhibit at the Aircraft Interiors Expo in Hamburg from March 31st to April 2nd 2020.”