Textination Newsline

Reset
5 results
(c) STFI
14.12.2021

Funding Project Raw Material Classification of Recycled Fibers

For centuries, old textiles have been used to make tear fibers and processed into new textile products. This effective recycling is one of the oldest material cycles in the world. Today, it is not only clothing that is recycled, but also high-quality technical textiles. As the products of the textile industry evolve, so do the demands on textile recycling. The basis for this is a clear assessment and classification of raw materials.

For centuries, old textiles have been used to make tear fibers and processed into new textile products. This effective recycling is one of the oldest material cycles in the world. Today, it is not only clothing that is recycled, but also high-quality technical textiles. As the products of the textile industry evolve, so do the demands on textile recycling. The basis for this is a clear assessment and classification of raw materials.

In the research project of the German Institutes of Textile and Fiber Research Denkendorf (DITF) and the Sächsisches Textilforschungsinstitut e.V. (STFI - Saxony Textile Research Institute), a methodology is being developed that will make it possible to analyze the tearing as well as the subsequent processes with regard to fiber quality. The systematic analysis should make it possible to optimize the subsequent spinning processes in such a way that the recycled content of the yarn can be increased without the yarn properties differing significantly from those of a yarn consisting of 100% good fibers. These yarns can then be processed into sustainable textile products such as clothing or composite components.

The project, which is funded by the BMWi/IGF, is scheduled to run for two years and will end on December 31, 2022. The main benefits for the participating companies are to enable them to make greater use of secondary raw materials, to open up new markets through technologies or products developed in the project, to initiate synergies and long-term cooperation, and to prepare a joint market presence.    

The project includes several steps:

  • Material selection and procurement
    Cotton fibers to be processed are obtained from used textiles (T-shirts) and waste from the cotton spinning mill. Aramid fibers are processed from used protective clothing and technical textiles.
  • Optimization of the preparation / dissolution of the textiles
    To ensure that the fibers are detached from the corresponding textiles as gently as possible and with a not too high reduction, exact settings have to be found for the tearing process, which are technologically very demanding and require a lot of experience.
  • Determination of the quality criteria for the evaluation of the fiber dissolution
    In order to define the quality criteria, the fibers coming from the tearing mill are determined by means of an MDTA-4 measuring device from Textechno GmbH & Co. KG. The criteria determined are to be used to characterize the (lowest possible) fiber shortening caused by the tearing process.
  • Determination of optimized settings in the spinning process
    In order to determine the optimum settings for producing a yarn from the recycled fibers, they are spun after the rotor spinning process. By adjusting the spinning process, the aim is to produce a yarn that has good uniformity and also appropriate firmness.
  • Production and comparison of yarns from recycled raw materials
    In order that the recycled fibers - consisting of aramid and cotton - can each be used to produce an area-measured material, the material is to be processed at industrial scale. For this purpose, the fibers are processed over a complete blowroom line with following sliver production over adapted cards. After drawing and the following roving production, yarns are produced according to the rotor or ring spinning process. The finished yarns are used to produce knitted fabrics.
  • Coordination, analysis of results and preparation of reports
    The final report is prepared by the DITF and the STFI. The results will be transferred through publications, technical information to associations and trade fair presentations. Regular meetings with the participating companies are planned.

Textination spoke with Stephan Baz, Deputy Head of the Competence Center Staple Fiber, Weaving & Simulation, Head of Staple Fiber Technology and Markus Baumann, Research Associate at the Competence Center Staple Fiber, Weaving & Simulation (both DITF) as well as Bernd Gulich, Head of Department Nonwovens/Recycling and Johannes Leis, Research Associate Focus Nonwovens/Recycling (both STFI) about the current status of the funding project.

What is the current status of the project?
We are currently in the phase of carrying out trials and the iterative optimization of several project components. As expected, several loops are necessary for the mechanical preparation itself and also for the adjustment of the spinning process with the different variants. Ultimately, after all, the project aims at coordinating the processes of mechanical preparation and spinning as processing in order to achieve optimum results. At the same time, determining the quality criteria of the fibers produced is not trivial. This also requires the further development of processes and test methods that can be implemented productively in industry and that allow the quality of the fibers produced to be assessed effectively and unaffected by residual yarns, for example. What is really remarkable is the interest and willingness of the industry to drive the project work forward. The considerable quantities of materials required for our trials were purchased from ReSales Textilhandel und -recycling GmbH, Altex Textil-Recycling GmbH & Co. KG and Gebrüder Otto GmbH & Co. KG. Furthermore, with Temafa Maschinenfabrik GmbH, Nomaco GmbH & Co. KG, Schill + Seilacher GmbH, Spinnerei Neuhof GmbH & Co. KG and Maschinenfabrik Rieter AG, many members of the project-supporting committee are actively involved in the project, from consulting to the providing of technologies. The company Textechno Herbert Stein GmbH & Co. KG has provided a testing device of the type MDTA4 for the duration of the project and supports our work with regard to the evaluation of the mechanically prepared fibers. We are of course particularly pleased about this, as it has allowed us to look at and analyze several technologies in both mechanical preparation, testing and spinning. We expect to be able to make more detailed statements at the beginning of the coming year.

Which approaches do you think are particularly promising?
With regard to technologies, we must refer to the evaluation and analysis of the trials, which are currently still ongoing. We will be able to go into more detail in the first quarter of next year.

Of course, things are already emerging. With meta-aramid waste, promising approaches could be found very quickly; with post-consumer cotton, this is considerably more complex. Obviously, there is a link between the quality of the raw material and the quality of the products. In some cases, we have already been able to determine very low average fiber lengths in the procured goods; to a certain extent, these are of course directly reflected in the output of our processes. From this, and this is not a new finding, a great importance of the design of the textiles is again derived.

What are the challenges?
In addition to the expected high short fiber content, the residual yarns after the tearing process are an issue of particular focus. The proportion of these residual yarns can vary between the materials and preparation technologies, but the further dissolution of the products of the tearing process is essential.

If the processes are considered further in a utilization phase, the question of design naturally also arises for the best possible use of recycled fibers. Many problems, but also the approaches to solutions for the use of comparatively short fibers, can also be expected to apply to the (multiple) use of mechanically recycled fibers.

Can we speak of upcycling in the final product?
We see yarn-to-yarn recycling neither as upcycling nor downcycling, but as closed-loop recycling. The background is that the products are to go into the same application from which they came and have to compete with primary material. This means that certain specific requirements have to be met and at the same time there is considerable price pressure. In the case of downcycling, a significant reduction in properties is accepted, while in the case of upcycling, the higher-priced application can make up for the reprocessing effort. In the attempt to produce yarn material again from yarn material, both are only permissible to a small extent. This represents the particular challenge.

What does a recyclate prepared from used textiles mean for the spinning process?
Part of this question is to be answered in the project by the detailed classification of the processed fibers and is thus the subject of the tests currently underway. It turns out that, in addition to the rather obvious points such as significantly reduced fiber length, process disturbances due to undissolved fabrics and yarn pieces, there are also less obvious aspects to be considered, such as a significantly increased outgoing quantity for processing in the spinning process. The outgoing quantity is of particular interest here, because in the end the newly produced yarn should also contain a considerable proportion of prepared fibers.

What consequences does this have for textile machinery manufacturing?
The consequences that can already be estimated at the present time are that, particularly in the processing of cotton, the machinery in the spinning preparatory mill is specialized in the processing of (new) natural fibers with a certain amount of dirt. In contrast to new fibers, processed fibers are clean fibers with a significantly higher proportion of short fibers. Elements that are good at removing dirt also reject an increased amount of short fibers, which can lead to unintentionally high waste quantities under certain circumstances. It is therefore necessary to adapt the established machine technology to the new requirement profile of the raw material "processed fibers". Analogous adaptations are probably necessary along the entire processing chain up to the yarn. In the drafting system of the spinning machine, of course, this is due more to the high short fiber ratio than to elements that have been optimized for cleaning out dirt and foreign substances.

Source:

Textination GmbH

Photo: pixabay
24.08.2021

Air, Water, Oil: What PLA bioplastic can filter well - and what not

Air filters have been discussed so often in recent days in the fight against the pandemic. With filter material made of nonwoven fabric, they block the way back into rooms for aerosols containing viruses. But how can these devices not only protect health, but also be operated with filter material that is as environmentally friendly as possible?

Air filters have been discussed so often in recent days in the fight against the pandemic. With filter material made of nonwoven fabric, they block the way back into rooms for aerosols containing viruses. But how can these devices not only protect health, but also be operated with filter material that is as environmentally friendly as possible?

Under clearly defined conditions, the bioplastic polylactide (PLA), also known as polylactic acid, is suited for this purpose. This can be deduced from results obtained by researchers from the Zuse community in the recently completed "BioFilter" research project. The key question for this and other potential applications of biofilters is: How do the special properties of PLA affect the filter performance and durability? After all, PLA can have practical disadvantages compared to its fossil-based competitors. Its material tends to be brittle and it doesn't particularly like high temperatures beyond 60 degrees Celsius. As a biogenic material, polylactic acid is also potentially more susceptible to abrasion and organic degradation processes. This can play an even greater role in the use of filters, e.g. in sewage treatment facilities, than in air filters. Industrial customers, however, naturally want a durable, reliable product.

From monofilament to nonwoven
Against this background, the researchers studied the PLA properties in order to test nonwovens for biofilters on this basis. The German Textile Research Center North-West (German Textile Research Center North-West - DTNW) and the Saxon Textile Research Institute (STFI), where the nonwovens were produced, were involved. Granules from various commercially available manufacturers were used. However, the research did not start with nonwovens, in which the fibers are deposited close together in different layers, but with so-called monofilaments, i.e. fibers made of PLA that are comparable to threads. DTNW and STFI initially carried out tests on these monofilaments, e.g. in a climate chamber for aging and durability.

As can be seen in the picture, the monofilaments became brittle after only two weeks at higher temperatures from 70 degrees Celsius, as the DTNW authors recently reported in the Journal Applied Polymer Materials. Under normalized conditions, however, the monofilaments showed no measurable reduction in stability even after almost three years, and the PLA nonwovens were in no way inferior to their fossil-based counterparts in terms of filter performance. "In my opinion, the focus for the use of PLA as a filter material will be on applications where relatively low temperatures are present, with which PLA copes very well," says DTNW scientist Christina Schippers.

Besides temperature and humidity consider other factors
For the researchers, however, the project, which was funded by the German Federal Ministry for Economic Affairs and Energy, was not just about the suitability of polylactide for air filters, but also for other applications, such as filtering water. In addition, the research revealed that when evaluating filter media made from bio-based and biodegradable nonwovens, it is important to consider other influencing factors, such as mechanical loads caused by air currents, in addition to temperature and humidity. "The innovative core of the project was to evaluate the possibilities and application limits of PLA nonwovens as filter media with sufficient mechanical properties and long-term stability," says project leader Dr. Larisa Tsarkova. Like her colleagues at STFI, DTNW is involved in the Zuse Community's Bioeconomy Cluster, in which researchers from nonprofit institutes cooperate under the guiding principle of "Researching with Nature." "For us, the bioeconomy is a top cross-industry topic that connects numerous institutes of the Zuse Community and is lived through collaborations such as with the 'Bio-Filter'," explains the future STFI managing director Dr. Heike Illing-Günther.

Cooperation in the Bioeconomy Cluster
With the results obtained from the "Bio-Filter" project, DTNW and STFI now want to continue working in order to be able to make derivations for clearly described areas of application for PLA nonwoven filters in the future. These possible fields of application extend far beyond room air filters and thus beyond the pandemic. For example, the water-repellent property of PLA is potentially interesting for filters in large-scale kitchens for water-oil filtration or also in the industry for engine oils.

The research is also so important, because PLA is already quite well established in individual consumer-related segments - keyword: carrier bags. Traditionally, lactic acid was used to preserve food, for example in sauerkraut. Today, PLA is obtained via a multi-stage synthesis from sugar, which ferments to lactic acid and polymerizes this to PLA, as Kunststoffe.de explains. PLA is one of the best-known bioplastics, but has not always been readily available due to strong demand in recent years. The Netherlands-based company Total Corbion has announced plans to start up a PLA plant with an annual capacity of 100,000 tons in Grandpuits, France, by 2024. It would be the largest plant of its kind in Europe, with Asia leading the way so far.

Source:

Deutsche Industrieforschungsgemeinschaft Konrad Zuse e.V.

Photo: Pixabay
16.02.2021

Carbon with Multiple Lives: Bringing Innovations in Carbon Fiber Recycling to Market

When it comes to the future of motorized mobility, everyone talks about the power drive: How much e-car, how much combustion engine can the environment tolerate and how much do people need? At the same time, new powertrains place ineased demands not only on the engine, but also on its housing and the car body: Carbon fibers are often used for such demanding applications. Like the powertrain of the future, the materials on the vehicle should also be environmentally friendly. That is why recycling of carbon fibers is required. Institutes of the Zuse Community have developed solutions for this.

Carbon fibers consist almost completely of pure carbon. It is extracted from the plastic polyacrylonitrile at 1,300 degrees Celsius, using a lot of energy. The advantages of carbon fibers: They have almost no dead weight, are enormously break-resistant and sturdy. These properties are needed, for example, in the battery box of electric vehicles in structural components of a car body.

When it comes to the future of motorized mobility, everyone talks about the power drive: How much e-car, how much combustion engine can the environment tolerate and how much do people need? At the same time, new powertrains place ineased demands not only on the engine, but also on its housing and the car body: Carbon fibers are often used for such demanding applications. Like the powertrain of the future, the materials on the vehicle should also be environmentally friendly. That is why recycling of carbon fibers is required. Institutes of the Zuse Community have developed solutions for this.

Carbon fibers consist almost completely of pure carbon. It is extracted from the plastic polyacrylonitrile at 1,300 degrees Celsius, using a lot of energy. The advantages of carbon fibers: They have almost no dead weight, are enormously break-resistant and sturdy. These properties are needed, for example, in the battery box of electric vehicles in structural components of a car body.

The Saxon Textile Research Institute (STFI), for instance, is currently working with industrial partners on combining the static-mechanical strengths of carbon fibers with vibration damping properties to improve the housings of electric motors in cars. The project, which is funded by the German Federal Ministry for Economic Affairs and Energy, is aimed at developing hybrid nonwovens that contain other fibers, in addition to carbon fiber, as a reinforcement. "We want to combine the advantages of different fiber materials and thereby develop a product that is optimally tailored to the requirements", explains Marcel Hofmann, head of department of Textile Lightweight Construction at STFI.

The Chemnitz researchers would therefore complement previous nonwoven solutions. They look back on 15 years of working with recycled carbon fibers. The global annual demand for the high-value fibers has almost quadrupled in the past decade, according to the AVK Industry Association to around 142,000 t most recently. "Increasing demand has brought recycling more and more into focus", says Hofmann. According to him, carbon fiber waste is available for about one-tenth to one-fifth of the price of primary fibers, but they still need to be processed. The key issue for the research success of recycled fibers is competitive applications. STFI has found these not only in cars, but also in the sports and leisure sector as well as in medical technology, for example in components for computer tomography. "While metals or glass fibers cast shadows as potential competing products, carbon does not interfere with the image display and can fully exploit its advantages", explains Hofmann.
 
Using Paper Know-How
If recycled carbon fibers can pass through the product cycle again, this significantly improves their carbon footprint. At the same time it applies: The shorter the carbon fibers, the less attractive they are for further recycling. With this in mind, the Cetex Research Institute and the Papiertechnische Stiftung (PTS), both members of the Zuse Community, developed a new process as part of a research project that gives recycled carbon fibers, which previously seemed unsuitable, a second product life. "While classic textile processes use dry processing for the already very brittle recycled carbon fibers in fiber lengths of at least 80 mm, we dealt with a process from the paper industry that processes the materials wet. At the end of the process, in very simplified terms, we obtained a laminar mat made of recycled carbon fibers and chemical fibers", says Cetex project engineer Johannes Tietze, explaining the process by which even 40 mm short carbon fibers can be recycled into appealing intermediates.

The resulting product created in a hot pressing process serves as the base material for heavy-duty structural components. In addition, the mechanical properties of the semi-finished products were improved by combining them with continuous fiber-reinforced tapes. The researchers expect the recycled product to compete with glass-fiber-reinforced plastics, for example in applications in rail and vehicle construction. The results are now being incorporated into further research and development in
the cooperation network of Ressourcetex, a funded association with 18 partners from industry and science.

Successful Implementation in the Automotive Industry
Industrial solutions for the recycling of carbon fiber production waste are being developed at the Thuringian Institute of Textile and Plastics Research (TITK). Several of these developments were industrially implemented with partners at the company SGL Composites in Wackersdorf, Germany. The processing of the so-called dry waste, mainly from production, is carried out in a separate procedure. "Here, we add the opened fibers to various processes for nonwoven production", says the responsible head of the department at TITK, Dr. Renate Lützkendorf . In addition to developments for applications e.g. in the BMW i3 in the roof or rear seat shell, special nonwovens and processes for the production of Sheet Molding Compounds (SMC) were established at TITK. These are thermoset materials consisting of reaction resins and reinforcing fibers, which are used to press fiber-plastic composites. This was used, for example, in a component for the C-pillar of the BMW 7 Series. "In its projects, TITK is primarily focusing on the development of more efficient processes and combined procedures to give carbon fiber recycling materials better opportunities in lightweight construction applications, also in terms of costs", says Lützkendorf. The focus is currently on the use of CF recycled fibers in thermoplastic processes for sheet and profile extrusion. "The goal is to combine short- and continuous-fiber reinforcement in a single, high-performance process step."

1) Since February 1st, 2021, Dr.-Ing. Thomas Reussmann succeeds Dr.-Ing. Renate Lützkendorf, who retired 31 January.

Source:

Zuse Community

(c) Pixabay
15.12.2020

Protection against Corona: Materials research provides findings at institutes of the Zuse Community

As the year draws to a close, expectations are growing that protection against COVID-19 will soon be available. Until this is the case for large sections of the population, the successes achieved in research and industry to protect against the virus in 2020 offer a good starting point in the fight against corona and beyond. At institutes in the Zuse community, progress have been made not only in medical but also in materials research.

As the year draws to a close, expectations are growing that protection against COVID-19 will soon be available. Until this is the case for large sections of the population, the successes achieved in research and industry to protect against the virus in 2020 offer a good starting point in the fight against corona and beyond. At institutes in the Zuse community, progress have been made not only in medical but also in materials research.

These successes in materials research include innovations in the coating of surfaces. "In the wake of the pandemic, the demand for antiviral and antimicrobial surfaces has risen sharply, and we have successfully intensified our research in this area," explains Dr. Sebastian Spange, Head of Surface Technology at the Jena research institute INNOVENT. He expects to see an increasing number of products with antiviral surfaces in the future. "Our tests with model organisms show that an appropriate coating of surfaces works", emphasizes Spange. The spectrum of techniques used by INNOVENT includes flame treatment, plasma coating and the so-called Sol-Gel process, in which organic and inorganic substances can be combined in one layer at relatively low temperatures. According to Spange, materials for the coatings can be antibacterial metal compounds as well as natural substances with antiviral potential.

Nonwovens produced for mask manufacturers
In 2020, the textile expertise of numerous institutes in the Zuse community ensured that application-oriented research could prove its worth in the practical fight against pandemics. After the shortage of mask supplies in Germany at the beginning of the pandemic, textile research institutes reacted to the shortage by jumping into the breach. The Saxon Textile Research Institute (STFI), for example, converted its research facilities to the production of nonwovens to supply German and European manufacturers of particle filtering protective masks. "From March to November 2020, we supplied nonwovens to various manufacturers in order to provide the best possible support for mask production and thus help contain the pandemic. At a critical time for industry and the population, we were able to help relieve critical production capacity - an unaccustomed role for a research institute, but one we would assume again in similar situations," explains Andreas Berthel, Managing Commercial Director of STFI.

Development of reusable medical face masks
For the improvement of everyday as well as medical face masks the German Institutes for Textile and Fiber Research (DITF) are working on this project. In cooperation with an industrial partner, they are currently developing in Denkendorf, among other things, reusable medical face masks made of high-performance precision fabric using Jacquard weaving technology. The multiple use avoids waste and possible supply bottlenecks.

There are regulations for all types of masks, now also for everyday masks. At Hohenstein, compliance with standards for masks is checked. A new European guideline defines minimum requirements for the design, performance evaluation, labelling and packaging of everyday masks. "As a testing laboratory for medical products, we test the functionality of medical masks from microbiological-hygienic and physical aspects", explains Hohenstein's Managing Director Prof. Dr. Stefan Mecheels. In this way, Hohenstein supports manufacturers, among other things, with technical documentation to prove the effectiveness and safety. Respiratory protection masks (FFP 1, FFP 2 and FFP 3) have been tested at the Plastics Centre (SKZ) in Würzburg since the middle of this year. Among other things, inhalation and exhalation resistance and the passage of particles are tested. In addition, SKZ itself has entered into mask research. In cooperation with a medical technology specialist, SKZ is developing an innovative mask consisting of a cleanable and sterilizable mask carrier and replaceable filter elements.

ILK tests for mouth-nose protection
The fight against Corona is won by the contributions of humans: Of researchers in laboratories, of developers and manufacturers in the Industry as well as from the citizens on the street.
Against this background, the Institute for Air and Refrigeration Technology (ILK) in Dresden has carried out investigations into the permeability of the mouth and nose protection (MNS), namely on possible impairments when breathing through the mask as well as the protective function of everyday masks. Result: Although the materials used for the mouth-nose protection are able to retain about 95 percent of the exhaled droplets, "under practical aspects and consideration of leakages" it can be assumed that about 50 percent to 70 percent of the droplets enter the room, according to the ILK. If the mask is worn below the nose only, it can even be assumed that about 90 percent of the exhaled particles will enter the room due to the large proportion of nasal breathing. This illustrates the importance of tight-fitting and correctly worn mouth and nose protection. "On the other hand, from a physical point of view there are no reasons against wearing a mask", ILK managing director Prof. Dr. Uwe Franzke emphasizes. The researchers examined the CO2 content in the air we breathe as well as the higher effort required for breathing and based this on the criterion of overcoming the pressure loss. "The investigations on pressure loss showed a small, but practically irrelevant increase," explains Franzke.

The complete ILK report "Investigations on the effect of mouth and nose protection (MNS)" is available here.

Shopping malls Photo: Pixabay
24.07.2018

NEW TRENDS IN ITALIAN RETAIL OPEN UP OPPORTUNITIES

  • Franchising takes off, more and more German retail chains discover Italy

Milan (GTAI) - The Italian retail sector is modernizing and the franchise economy is growing. Italian franchise systems are gaining ground. New modern shopping centers, including the largest in Europe, create space for new shops. German retail chains are expanding in many segments, from discount food and other consumer goods to services. Northern Italy is considered a popular test site. High quality and a price advantage are the keys to success.

  • Franchising takes off, more and more German retail chains discover Italy

Milan (GTAI) - The Italian retail sector is modernizing and the franchise economy is growing. Italian franchise systems are gaining ground. New modern shopping centers, including the largest in Europe, create space for new shops. German retail chains are expanding in many segments, from discount food and other consumer goods to services. Northern Italy is considered a popular test site. High quality and a price advantage are the keys to success.

The Italian retail sector is changing. The number of classic corner shops is declining, the modern organized retail trade is growing. The franchise economy in particular is developing positively. Beyond the classical areas such as food and fashion, various Italian franchise systems are spreading more and more visibly in the big cities.
 
According to the industry association Assofranchising, the franchise industry had a turnover of approximately EUR 24.6 billion in 2017. This represents an increase of 2.6 percent compared to the previous year and an increase of 5.7 percent since 2014. With a similar number of systems (929 in Italy, 972 in Germany), the German franchise industry generated almost five times as much turnover. One reason for this is that German franchise systems have on average more than three times as many businesses per franchise.

Development of the franchise economy in Italy
  2016 2017 Change (in %)
Sales (Euro Mio.)  23,930 24,545 2.6
Franchise systems 950 929 -2.2
Businesses 50,720 51,671 1.9
Italian businesses abroad 7,871 10,079 28.1
Italian businesses abroad (min. 3 companies) 169 179 5.9
Foreign systems in Italy 61 71 16.4
Employees 195,303 199,260 2.0
Average size of systems in Italy (number of companies) 53.4 55.6 4.2
Average size of Italian systems abroad (number of companies) 46.6 56.3 20.9

   Source: Rapporto Assofranchising 2018

But the segment is catching up in Italy. Italian franchise systems are expanding, also abroad. Outside Italy, their number increased by around 6 percent in 2017, while their average size (measured by the number of businesses) increased by around 21 percent. The domestic average dimension is also growing. The country is also becoming more attractive for foreign franchisors. In 2017, the number of foreign franchise systems increased by 16 percent. The relevant trade fair is the Salone Franchising, which will take place from October 25th to 27th 2018 in Milan.   

New shopping centers are driving the developments forward
Developments in the retail sector are accompanied by new construction projects. A number of new shopping centers are currently under construction in Italy, creating space for the new generation of franchises and retail chains. The major CityLife project on the former Milan exhibition grounds is a current example. In addition to two of the three planned skyscrapers (including Allianz's new headquarter in Italy), a new shopping center was inaugurated in autumn 2017. Particularly in the catering sector new Italian chains, which are expanding nationwide, can be seen. A new gastronomy floor with restaurants and cafés in the middle price segment was recently inaugurated at the Termini railway station in Rome.

A number of modern shopping centers are still under construction, including the new Westfield Milan. Project operators describe it as the largest shopping center in Europe. With an investment EUR 1.4 billion Westfield Milan is to be inaugurated in 2020. The majority of the new construction projects are located in the larger cities in the north, but Rome and Naples will soon receive new shopping centers also.

Shopping centers under construction in Italy
Designation Investment (Mio. Euro) Area (1,000 sqm) Completion Remarks
Westfield, Milan 1,400 60 2020

http://www.westfieldcorp.com

Maximo, Rome 300 61 2019 Cushman & Wakefield
Emilia Shopping District, Parma 200 74 2019

http://www.sonaesierra.com

Maximall Pompeii, Napoli 150 200 2019

http://www.maximall.it/pompeii

Falcon Malls Cascina Merlata, Milan n.a. 65 2021 http://falconmalls.it
Falcon Malls Concordia, Milan n.a. 131 2021 http://falconmalls.it
Waltherpark Shopping - Bozen 23 k.A. 2021

https://waltherpark.com

    Source: Research of Germany Trade & Invest

Opportunities for German retail chains
Another trend in Italy is the expansion of German retail chains. One growth area is the market for discount foods. According to Nielsen, discounters had a market share of 17 percent of the sold food at the end of 2017. The market leader is Eurospin from Italy, followed by Lidl. In 2018 Aldi opened its first store in northern Italy and by the end of 2018 it is planned to open 45 stores. Lidl is defending itself against its new competitor with planned investments in Italy amounting to EUR 350 mio for a new inner-city store concept. A total of 40 new points of sale are planned, and a further 50 stores are to be modernized.

Both German supermarket chains confirm that a local strategy for Italian gourmets is indispensable. Lidl sources 80 percent of its food products from Italy, while Aldi's share is almost as high at 75 percent.

In terms of price, the recipe for success of the German retail chains is somewhat different from Germany. Although German retailers continue to score with a good price-performance ratio, the focus in Italy is on the mid-price segment.

The latest example is the drugstore chain dm. The first branch was inaugurated at the end of 2017. There are plans to open 100 stores in northern Italy by 2020. dm offers not only a price advantage over its Italian competitors, but also high-quality products. In addition, there are hardly any "one-stop shops" in Italy, which are also drugstores, but also sell beauty products, organic and natural products as well as baby products.   

The Douglas perfumery chain is expanding also in Italy. At the end of 2017, Douglas' parent company completed the acquisition of two of the leading perfumeries in Italy, Limoni and La Gardenia.    

Fielmann is another example of a German chain that has conquered the Italian market in recent years with high-quality products and a price advantage. With entry into the South Tyrol market and ongoing expansion in northern Italy, Fielmann is popular with Italian consumers despite the large competing manufacturers of glasses in Italy due to its price advantages.

Germany's successful model is not limited to food and other consumer goods. The Berlin-based company Flixbus is an example that the concept of quality and price competition can also be successfully applied to the service sector. Flixbus has been in Italy since 2015 and the number of passengers is increasing constantly. In 2017, 40 million Italians were on the road with Flixbus, twice as many as the year before. Italy is the fastest growing market among 26 countries for the company.

More information:
Italy Franchisesysteme Retail
Source:

Robert Scheid, Germany Trade & Invest www.gtai.de